Specification sheet Deltapi N Series

Pneumatic Transmitters
Model NAE
Differential pressure transmitter
with remote diaphragm seals
GENERAL CHARACTERISTICS
The blind type differential pressure transmitter, mod. NAE, is
used to measure a differential pressure and convert it into a
proportional pneumatic signal.
The instrument works on the force-balance principle and
consists of two main units:

the measuring unit is formed by two AISI 316 forged

halfbodies, measuring capsule and two diaphragm separators
completed with capillaries.
A double diaphragm capsule is placed within two halfbodies to
releve the differential pressure transmitted by the two liquid
filled separators and capillaries.
The capsule is available in two versions: 2in or 3in diameter
diaphragms, filled with a special liquid which can withstand the
maximum rated static pressure on either side without damage.

the transmission unit converts the differential force applied to

the measuring element into a proportional output pneumatic
signal.
The output pressure, generated by a flapper nozzle relay, is fed
to a feedback bellows with a rising pressure until the bellows
force balances that of the measuring element.

Span value continuously adjustable by an internal micrometric

screw.

Zero value adjustable by an external screw.

Mounting in a vertical position on 2in diameter pipe by a

special bracket.

OPTIONAL EXTRA FEATURES

A zero elevation or suppression device allows to set as a

zero of the transmitter a measured variable value different from Air filter regulator can be directly mounted on the transmitter,
zero. with or without pressure gauge, and connected with piping and
Zero suppression value (S) added to the calibrated span must fittings either in stainless steel or copper.
never exceed the upper range limit (M) of measuring capsule: Special versions of air filter regulator and gauges, in stainless
S + span ≤ M (see table). steel, are available on request.
SPECIFICATIONS
The data were obtained from laboratory tests on standard instruments with: AISI 316L bodies; AISI 316L measuring element ; silicone
oil (DC200) filling; gasket: PTFE; calibration span: 18 kPa - 180 mbar (for 3in diaphragm), 70 kPa - 700 mbar (for 2in diaphragm)

MEASURING SPAN RANGE MAXIMUM MAXIMUM STATIC PRESSURE

CAPSULE LIMITS LIMITS ZERO ZERO LIMITS
(DIAPHRAGM DIA.) min. and max. lower and upper (M) SUPPRESSION (S) ELEVATION Full vacuum and

2 in 40 and 170 kPa -170 and +170 kPa 130 kPa 170 kPa 10 MPa
400 and 1700 mbar -1700 and +1700 mbar 1300 mbar 1700 mbar 100 bar
or flange/fitting rating
10 and 52 kPa -52 and +52 kPa 42 kPa 52 kPa of the seal whichever
3 in
100 and 520 mbar -520 and +520 mbar 420 mbar 520 mbar is less (•)

(•) Equal to Maximum Working pressure as well as overrange limit.

Air supply Seal diaphragm materials

nom. 140 kPa (1.4 bar, 20 psi); min. 125 kPa (1.25 bar, AISI 316L, Hastelloy C 276, Tantalum,
18 psi); max. 175 kPa (1.75 bar, 25 psi) AISI 316L or Hastelloy C 276 with Teflon anti-stick coating,
AISI 316L with Teflon coating anti-corrosion and anti-stick
Output signal
20 to 100 kPa/0.2 to 1 bar, 3 to 15 psi or 0.2 to 1 kg/cm2 Measuring capsule material
AISI 316L
Static air consumption
350 Nl/h Capsule filling
Silicone oil
Maximum output flow
- with rising output pressure: 30 Nl/min. Seal filling / working temperature range
- with falling output pressure: 40 Nl/min. See table "A"

Accuracy Cover material

± 0.5% F.S.D. (typical) thermoplastic resin

Differential thermal drift (for ambient temperature variation Surface protections

of 20°C between the separators) AISI 316L body and flange: none
2%/10° C
Process connections
Thermal drift (for ambient temperature variation between - wafer remote seals: 3in ASME150 to 900;
- 20° C and + 65° C) DN80 DIN ND 10 to 160
• with 2in diaphragm - flush diaphragm flanged seal: 3in ASME150 to 900;
span 40 to 80 kPa (400 to 800 mbar): 0.7%/10°C DN80 DIN ND 16 to 160
span 80 to 170 kPa (800 to 1700 mbar): 0.6%/10°C - extended diaphragm flanged seal: 3in ASME 150-300;
• with 3in diaphragm DN80 DIN ND 16-40
span 10 to 52 kPa (100 to 520 mbar): 0.6%/10°C
Pneumatic connections
- Static pressure effect : - Air supply (in figure ref. A): 1/4 in NPT-F
for variation of 3.5 MPa (35 bar): ≤ ± 0.25% - Output (in figure ref. B): 1/4 in NPT-F

- Maximum displacement Pressure gauge

- with 2in diaphragm: 1 cm3 Brass with stainless steel case (all stainless steel on request)
- with 3in diaphragm: 1.5 cm3 external diameter 51 mm; 0-200 kPa, 0-2 bar and 0-30 psi
indication on 82 mm/260° scale.
Degree of protection in accordance with IEC 529
IP55 Air filter regulator
with copper or stainless steel piping, as specified.
Ambient temperature limits Die cast aluminium alloy with light grey epoxy finish.
-40 and + 120°C
Net weight (maximum)
Process temperature limits 23 kg approx
Same as fill fluid limits. Refer to table A.
204°C (400°F) for use with Teflon anti-stick coating. Packing
expanded polythene box
Bodies material
AISI 316L
TABLE 'A' - FILL FLUIDS CHARACTERISTICS

OPERATING CONDITIONS SPECIFICATIONS @ 25°C (77°F)

FILL FLUIDS Tmax °C (°F) Pmin Tmax °C (°F) Tmin Specific Viscosity Thermal
@ P >of mbar abs @ P min °C (°F) gravity Kinematic Expansions
(APPLICATION)
(psia) (cSt) x10-3 /°C
Silicone oil DC 200 200 (390) 0.7 160 -40
0.93 10 1.08
(General purpose) @ 35 mbar abs (0.1) (320) (-40)
Silicone oil DC 702 315 (600) 0.7 200 -7
1.07 45 0.78
(High temperature) @ atmosphere (0.1) (390) (+20)
Silicone oil DC 704 340 (645) 0.7 230 20
1.07 42 0.95
(High temperature) @ atmosphere (0.1) (445) (70)
Neobee M-20 200 (390) 130 150 -18
@ atmosphere (1.9) (300) (0) 0.92 9.8 1.2
(Food-Sanitary)
Glycerin Water (70%) 93 (200) atmosphere 93 -7
(Food-Sanitary) @ atmosphere (200) (+20) 1.08 2.2 0.36
DC 97-9120 200 (390) 0.7 160 -40
PHARMA B GRADE @ 35 mbar abs (0.1) (320) (-40) 0.96 50 1.04
(Food-Sanitary)
Inert (Galden) 160 (320) 0.7 65 -18
1.8 4.5 1.1
(Oxygen Service) @ atmosphere (0.1) (150) (0)
KTFILL-1 300 (570) 0.7 160 -10
(320) (+14) 1 16 0.92
(Paints and specials) @ 400 mbar abs (0.1)

ORDERING INFORMATION
Select one character or set of characters from each category and specify complete catalog number.
In addition quote the required seal model from one of the enclosed N6 ordering information
abc de fg hi j k lm
PRODUCT CODE
BASE MODEL
VERSION
BODY
SPAN LIMITS
CONSTRUCTION
OUTPUT
EXTRAS
Code
abc BASE MODEL
Differential pressure transmitter with remote diaphragm seals NAE

de VERSION
Standard W1

fg BODY
AISI 316L 11

MEASURING ELEMENT
hi Diaphragm material Core material Filling Span limits kPa (inH2O) (Note 1)
AISI 316L AISI 316L Silicone oil 10 and 52 (40 and 208) 01
AISI 316L AISI 316L Silicone oil 40 and 170 (160 and 682) 10 02
Note 1: Multiply by 10 the value in kPa (MPa) to obtain mbar (bar)

j CONSTRUCTION
Transmitter with remote diaphragm seals (to be quoted separately as N6W, N6E or N6F) 2

k OUTPUT
3 to 15 psi 1
3 to 15 psi with zero elevation device 2
3 to 15 psi with zero suppression device 3
0.2 to 1.0 kg/cm2 According to 4
0.2 to 1.0 kg/cm2 with zero elevation device ANSI/ISA S 51.1-1979 5
0.2 to 1.0 kg/cm2 with zero suppression device standard terminology 6
20 to 100 kPa / 0.2 to 1 bar 7
20 to 100 kPa / 0.2 to 1 bar with zero elevation device 8
20 to 100 kPa / 0.2 to 1 bar with zero suppression device 9
EXTRAS
Identification Piping Air filter Pressure
lm tag material material regulator gauge
Stainless Steel -- -- -- 02
Stainless Steel Stainless Steel with -- 10
Stainless Steel Copper with -- 11
Stainless Steel Stainless Steel with with 13
Stainless Steel Copper with with 14
N6W WAFER REMOTE SEALS
Select one character or set of characters from each category and specify complete catalog number.

Code
abc BASE MODEL
Wafer remote seals N6W

d NUMBER OF REMOTE SEALS

Two remote seals 2

ef MOUNTING CONNECTION
3in ASME F3
DN80, DIN ND 10-40 D3
DN80, DIN ND 64-160 D8

g OTHER WETTED MATERIAL (Not diaphragm)

Same as diaphragm 0

h DIAPHRAGM MATERIAL
AISI 316L serrated seat finish 2
AISI 316L smooth seat finish L
Hastelloy C 276 3
Tantalum (max temperature 260°C/500°F) - (NOT VACUUM) 5
AISI 316L ss with Teflon anti-stick coating (only available with 7
Hastelloy C 276 with Teflon anti-stick coating code F3 at position "ef") 8
AISI 316L ss with Teflon coating anti-corrosion and antistick A

i EXTENSION LENGTH
None 0

j CAPILLARY - Fill fluid

Silicone oil (DC 200) A
Silicone oil (DC 702) C
Silicone oil (DC 704) D
Glycerin/Water G
Inert Fluid P
KTFILL-1 L
Neobee M-20 N
DC97 - 9120 PHARMA B-GRADE Q

kl SYSTEM LENGTH m(feet)

1 (3) 03
1.5 (5) 05
2 (7) 07
2.5 (8) 08
3 (10) 10
3.5 (12) 12
4 (13) 13
4.5 (15) 15
5 (17) 17
6 (20) 20
7.5 (25) 25
9 (30) 30
10 (35) 35

m CERTIFICATION
None 0

no OPTIONS
None 00
N6E FLANGED EXTENDED DIAPHRAGM SEALS
Select one character or set of characters from each category and specify complete catalog number.

Code
abc BASE MODEL
Flanged extended diaphragm seals N6E

d NUMBER OF REMOTE SEALS

Two remote seals 2

ef MOUNTING CONNECTION Material

3in ASME CL150 Carbon steel K3
3in ASME CL150 AISI 316 ss S3
3in ASME CL300 Carbon steel L3
3in ASME CL300 AISI 316 ss 36
DN80, DIN ND 16 Carbon steel 4C
DN80, DIN ND 16 AISI 316 ss 4M
DN80, DIN ND 40 Carbon steel 4D
DN80, DIN ND 40 AISI 316 ss 4N

g OTHER WETTED MATERIAL (Not diaphragm)

AISI 316L ss 2
Hastelloy C (only available with diaphragm material code 3, 8 and A at position "h") 3

h DIAPHRAGM MATERIAL
AISI 316L ss 2
Hastelloy C 276 3
AISI 316L ss with Teflon anti-stick coating (only available with 3in ANSI CL 150/300 7
Hastelloy C 276 with Teflon anti-stick coating connection, code K3,S3,L3,36 at position "ef") 8
AISI 316L ss with Teflon coating anti-corrosion and antistick A

i EXTENSION LENGTH
2in 2
4in 4
6in 6

j CAPILLARY - Fill fluid

Silicone oil (DC 200) A
Silicone oil (DC 702) C
Silicone oil (DC 704) D
Glycerin/Water G
Inert Fluid P
KTFILL-1 L
Neobee M-20 N

kl SYSTEM LENGTH m(feet)

1 (3) 03
1.5 (5) 05
2 (7) 07
2.5 (8) 08
3 (10) 10
3.5 (12) 12
4 (13) 13
4.5 (15) 15
5 (17) 17
6 (20) 20
7.5 (25) 25
9 (30) 30
10 (35) 35

m CERTIFICATION
None 0

no OPTIONS
None 00
N6F FLANGED FLUSH DIAPHRAGM SEALS
Select one character or set of characters from each category and specify complete catalog number.

Code
abc BASE MODEL
Flanged flush diaphragm seals N6F

d NUMBER OF REMOTE SEALS

Two remote seals 2

ef MOUNTING CONNECTION Material

3in ASME CL150 Carbon steel K3
3in ASME CL150 AISI 316 ss S3
3in ASME CL300 Carbon steel L3
3in ASME CL300 AISI 316 ss 36
3in ASME CL600 Carbon steel 37
3in ASME CL600 AISI 316 ss 38
3in ASME CL900 Carbon steel 39
3in ASME CL900 AISI 316 ss 3A
DN80, DIN ND 16 Carbon steel 4C
DN80, DIN ND 16 AISI 316 ss 4M
DN80, DIN ND 40 Carbon steel 4D
DN80, DIN ND 40 AISI 316 ss 4N
DN80, DIN ND 64 Carbon steel 4E
DN80, DIN ND 64 AISI 316 ss 4F
DN80, DIN ND 100 Carbon steel 4H
DN80, DIN ND 100 AISI 316 ss 4G
DN80, DIN ND 160 Carbon steel 4K
DN80, DIN ND 160 AISI 316 ss 4L

g OTHER WETTED MATERIAL (Not diaphragm)

Same as diaphragm 0

h DIAPHRAGM MATERIAL
AISI 316L serrated seat finish 2
AISI 316L smooth seat finish L
Hastelloy C 276 3
Tantalum (max temperature 260°C/500°F) - (NOT VACUUM) 5
AISI 316L ss with Teflon anti-stick coating (only available with 3in connection code 7
Hastelloy C 276 with Teflon anti-stick coating K3,S3,L3,36,37,38,39,3A at position "ef") 8
AISI 316L ss with Teflon coating anti-corrosion and antistick A

i EXTENSION LENGTH
None 0

j CAPILLARY - Fill fluid

Silicone oil (DC 200) A
Silicone oil (DC 702) C
Silicone oil (DC 704) D
Glycerin/Water G
Inert Fluid P
KTFILL-1 L
Neobee M-20 N
DC97 - 9120 PHARMA B-GRADE Q

kl SYSTEM LENGTH m(feet)

1 (3) 03
1.5 (5) 05
2 (7) 07
2.5 (8) 08
3 (10) 10
3.5 (12) 12
4 (13) 13
4.5 (15) 15
5 (17) 17
6 (20) 20
7.5 (25) 25
9 (30) 30
10 (35) 35

m CERTIFICATION
None 0

no OPTIONS
None 00

Compliance to NACE class II bolting, according to specification MR0175, latest revision

 MOUNTING DIMENSIONS

To remote
seals

• N6W Remote wafer seals

Raised Face
H Flange

DIMENSIONS mm (in)
SIZE
A (dia) B dia) H L

3 in 89 (3.5) 127 (5) 23 (0.9) 139.7 (5.5)

A

DN 80 89 (3.5) 138 (5.43) 23 (0.9) 139.7 (5.5)

Wafer seal maximum working pressure:

Process 16 MPa, 160 bar, 2320 psi but not greater than the
Connection backup flange rating (not supplied)
L

Capillary to
instrument
• N6F Remote flanged flush diaphragm seals • N6E Remote flanged extended diaphragm seals

F G F G

Capillary to Capillary to
Instrument Instrument

B
D
A
C

C
B
D
A

E
E

158 (6.22) 2", 4" or 6"Insertion

158 (6.22) length is available

SIZE/RATING A (dia) DIMENSIONS mm (in) N° of

flush extended B (dia) C (dia) D (dia) E (dia) F G holes
3in ASME CL 150 89 (3.5) 72 (2.83) 127 (5) 152.5 (6) 190.5 (7.5) 20 (0.79) 24 (0.94) 9.5 (0.37) 4
3in ASME CL 300 89 (3.5) 72 (2.83) 127 (5) 168.5 (6.63) 210 (8.26) 22 (0.86) 28.5 (1.12) 9.5 (0.37) 8
3in ASME CL 600 89 (3.5) 127 (5) 168.5 (6.63) 210 (8.26) 22 (0.86) 32 (1.26) 9.5 (0.37) 8
3in ASME CL 900 89 (3.5) 127 (5) 190.5 (7.5) 241 (9.48) 26 (1.02) 38.5 (1.51) 9.5 (0.37) 8
DN80 DIN ND16 89 (3.5) 72 (2.83) 138 (5.43) 160 (6.3) 200 (7.87) 18 (0.71) 20 (0.79) 9.5 (0.37) 8
DN80 DIN ND40 89 (3.5) 72 (2.83) 138 (5.43) 160 (6.3) 200 (7.87) 18 (0.71) 24 (0.94) 9.5 (0.37) 8
DN80 DIN ND64 89 (3.5) 138 (5.43) 170 (6.7) 215 (8.46) 22 (0.86) 28 (1.1) 9.5 (0.37) 8
DN80 DIN ND100 89 (3.5) 138 (5.43) 180 (7.08) 230 (9.05) 26 (1.02) 32 (1.26) 9.5 (0.37) 8
DN80 DIN ND160 89 (3.5) 138 (5.43) 180 (7.08) 230 (9.05) 26 (1.02) 36 (1.42) 9.5 (0.37) 8

Flanged seal maximum working pressure:

ASME CL 150: 2 MPa, 20 bar, 290 psi
ASME CL 300: 5 MPa, 50 bar, 725 psi
ASME CL 600: 10 MPa, 100 bar, 1450 psi
ASME CL 900: 16 MPa, 160 bar, 2320 psi
DIN ND 16: 1.6 MPa, 16 bar, 230 psi
DIN ND 40: 4 MPa, 40 bar, 580 psi
DIN ND 64: 6.4 MPa, 64 bar, 930 psi
DIN ND 100: 10 MPa, 100 bar, 1450 psi
DIN ND 160: 16 MPa, 160 bar, 2320 psi
SS/NAE Rev 8

The Company's policy is one of continuous product

improvement and the right is reserved to modify the
specifications contained herein without notice.

ABB Ltd ABB Inc. ABB SACE spa

Howard Road, St. Neots 125 E. County Line Road Business Unit Instrumentation
Cambridgeshire, PE19 8EU Warminster, PA 18974 Via Statale 113
UK USA 22016 Lenno (CO) Italy
Tel: +44(0)1480 475321 Tel: +1 215 674 6000 Tel: +39 0344 58111
Fax: +44(0)1480 217948 Fax: +1 215 674 7183 Fax: +39 0344 56278