Digital Temperature Controller Instruction Manual: 1 Product Check
Digital Temperature Controller Instruction Manual: 1 Product Check
Digital Temperature Controller Instruction Manual: 1 Product Check
YLD- INSTRUCTION MANUAL (2) Following cautions must be kept in mind while mounting:
Before using this product, please carefully read this manual for its correct use. In addition, after reading the Direct vibration or shock to the mainframe.
manual, keep it available easily anytime. Water, oil, chemicals, vapor or steam splashes.
Before cleaning the instrument, check that the power is turned off. Excessive induction noise, static electricity, magnetic fields or noise.
Please using the soft clothes or tissue paper to remove stains on the display unit. Direct airflow from an air conditioner.
Because the display unit is easily scratched, please do not scrub or touch it with a hard object. Should be used indoors where the system is not exposed to direct sunlight.
Do not operate the front key with a pointed object such as a ballpoint pen or screwdriver, as this may scratch or Shanghai Yatai Address:No.1851 North Sichuan Road, Shanghai, China
damage the key. Instrumentation Co., Ltd. Tel:021-51053127 51053128 Fax : 086-021-51053123
2. MOUNTING ⑸
(1) This instrument is intended to be used under the following environmental condition ⑺
Pt100
⑻ input low limit(Display input Lange) Automatically turn over after 4 seconds displaying
⑼
Upper row displays process value, lower Automatically return over when not press any key over 1 minute
After pulling out it the buzzer will be open current, the sound will cease. row displays set value(Standard mode)
5.1 Sequence to pick up the functions of the instrument value of St online, and the time passed can be memorized and the instrument will operate the updated timing
time. When the updated time is less than the passed accumulative
Power on time, the heating output close immediately, the buzzer sounds 4 times. The refrigeration output is working
continuously.
Upper row displays code(Sn),lower Row The method for changing control parameter:
displays type No. (Display input type) After press key over 4 seconds, find LK. Then press or key to the lower displayer display 18.Again
press the key to find the symbol character for the needed parameter. Through press the or key till the
Upper row: Input high limit, lower row high row displays display the parameter needed is reached. Some parameters may be setting at once. Press the
5.3 The function of the controller Auto-tuning on time to the on-off period in the equilibrium
After pressing /TIME key, The instrument displays the time have operated.
Ar (re-setting) 0100% 100
state. In the half proportional control, the Ar
After pressing /AT key 20 seconds the AT indicator flashes and the auto-tuning press starts; after the end of equals coefficient/P.
auto-tuning the AT indicator then be turned out. A set of PID parameters can be got automatically for overcoming For the thyristor output it is about 13 seconds.
temperature overshoot. The controller operates according to this set of PID parameters. For those equipment that the superfluous power
is working continuously. heating period 1300 seconds provided is comparatively larger, select larger T 3
In the period of auto tuning, if press /AT key beyond 20 seconds the AT indicator turn out and the auto tuning
T would decrease the stable error caused by PID
process is canceled. The instrument operated according to the original PID parameters. control.
Following table lists the function parameters When the zero error comparatively smaller and
Zero point adjust -100100 -100.0 the full point error comparatively larger, to
factory set 0
Symbol Name Setting range Description
value Pb (intersection) 100.0 update this value should be needed. Ordinary for
When temperature is beyond SP+AL, the ALM 50 When the zero error comparatively larger and
0 Full Range
Alarming setting indicator turn on. The buzzer sounds and the the full point error also comparatively larger, to
AL 0.0Full Range
heating power turn off. (50.0) Full point adjust
-10001000 update this value should be needed.
0
(intercept) seconds PK=4000×setting value –actual value /actual
When the temperature less than SP+COL, the PK
50 value. For Pt100 adjusting this value is need at
Refrigeration 0Full Range 0.0
refrigeration point is turn on to drive the
first time.
CL control setting Full Range
compressor. (50.0)
Refrigeration
When measuring value reaches its alarm value,
Proportional control action . if P is larger then 30 control Time 03600 seconds 60
1Full Range 1.0
Proportional Band the gain of system is lower. it only use on the Ct delayed
the alarm relay output will be delayed this time..
P Full Range
heating side. (30.0)
When D=0 the display resolving power is
The decimal Point
03600 0 1 1℃and when DP=1 the display resolving power 1
Integrated time constant. I larger, then the
Integral Time 240 dP setting
is 0.1℃
I seconds
integrated action is smaller.