GHR32QV

GHR32Q/V
Corp. 0001−L2
Revised 08−2004
Service Literature
GHR32Q/V SERIES UNITS
This manual contains information pertaining to

GHR32−1 through −6 model units. GHR32 series units
are high−efficiency horizontal or down flow gas furnaces
manufactured with Lennox DuralokPlust aluminized and
stainless steel clamshell-type heat exchangers. GHR32Q
units are available in heating input capacities of 50,000 to
120,000 Btuh (14.7 to 35.2 kW) and cooling applications
from 2 through 5 tons (7.0 through 17.6 kW). GHR32V units
are available in heating capacities of 75,000 and 100,000 Btuh
(22.0 and 29.3 kW) and 3 and 5 tons (10.5 and 17.5) for cool-
ing. Refer to Engineering Handbook for proper sizing.
Units are factory equipped for use with natural gas. A kit is
available for conversion to LPG operation. GHR32−1
through −4 units are equipped with the Lennox SureLight
silicon nitride ignition system. GHR32−5 units are
equipped with the two stage (V models will have the vari-
able speed control) integrated control board. Each
GHR32 unit meets the California Nitrogen Oxides (NO x )
Standards and California Seasonal Efficiency require-
ments. The gas valve is redundant to assure safety
shut−off as required by A.G.A. and C.G.A.
DOWN FLOW
The heat exchanger, burners and manifold assembly can be
POSITION
removed for inspection and service. The maintenance section
gives a detailed description on how this is done. GHR32Q MODEL SHOWN
Information contained in this manual is intended for
use by qualified service technicians only. All specifica-
tions are subject to change. Procedures outlined in this
manual are presented as a recommendation only and do
not supersede or replace local or state codes.
TABLE OF CONTENTS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 VII Wiring Diagram and Sequence of Operation . . . . 54
Specifications Q Models . . . . . . . . . . . . . . . . . . . . . . . . 2 GHR32Q−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Blower performance Q Models . . . . . . . . . . . . . . . . . . 3 GHR32Q−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Specifications V Models . . . . . . . . . . . . . . . . . . . . . . . . 4 GHR32Q−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Blower performance V Models . . . . . . . . . . . . . . . . . . . 5
GHR32V−1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Parts Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GHR32V−3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
I Unit Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
GHR32V−4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
II Placement and Installation . . . . . . . . . . . . . . . . . . . . 41
III Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 GHR32V−5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
IV Heating System Service Checks . . . . . . . . . . . . . . 47 VIII Operating Flow Charts . . . . . . . . . . . . . . . . . . . . . . 65

V Typical Operating Characteristics . . . . . . . . . . . . . . 49 IX Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
VI Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 X Blower Control Board Jumper Summary . . . . . . . . 87
Page 1 © 2000 Lennox Industries Inc.

Litho U.S.A.
SPECIFICATIONS GHR32Q MODELS
Model No. GHR32Q2/3-50 GHR32Q3-75 GHR32Q4/5-100 GHR32Q4/5-120
High Fire 50,000 (14.7) 72,000 (21.1) 100,000 (29.3) 118,000 (34.6)
Input Btuh (kW)
Low Fire 34,000 (10.0) 51,000 (14.9) 68,000 (19.9) 81,600 (23.9)
High Fire 47,000 (13.8) 67,000 (19.6) 93,000 (27.2) 111,000 (32.5)
Output Btuh (kW)
Low Fire 31,600 (9.3) 47,000 (13.8) 63,000 (18.4) 75,900 (22.2)
A.F.U.E. 90.0%
California Seasonal Efficiency 83.7% 83.9% 85.3% 84.0%
Exhaust pipe connection (PVC) diameter in. (mm) 2 (51)
Intake pipe connection (PVC) diameter in. (mm) 2 (51)
Condensate drain connection (PVC) in. (mm) 1/2 (12.7)
Temperature rise High Fire 30 − 60 (17 − 33) 40 − 70 (22 − 39) 45 − 75 (25 − 42)
range _F (_C) Low Fire 25 − 55 (14 − 31) 35 − 65 (20 − 36) 40 − 70 (22 − 39)
High static certified by (A.G.A./C.G.A.) in wg. (Pa) .50 (125)
Gas Piping Size I.P.S. in. (mm) 1/2 (12.7)
Blower wheel nominal in. 10 x 8 11-1/2 x 9
diameter x width mm 254 x 203 292 x 229
Number and size of filters − in. (mm) (1) 14 x 25 x 1 (356 x 635 x 25) (1) 20 x 25 x 1 (508 x 635 x 25)
Blower motor output hp (W) 1/3 (249) 1/2 (373) 3/4 (560)
Nominal cooling Tons 2 to 3 2 to 3.5 3.5 to 5
that can be added kW 7.0 to 10.6 7.0 to 12.3 12.3 to 17.6
Shipping weight lbs. (kg) 1 package 147 (67) 155 (70) 196 (89) 205 (93)
Electrical characteristics 120 volts 60 hertz 1 phase (less than 12 amps)
Optional Accessories (Must Be Ordered Extra)
LPG/Propane kit 59L81 (−1 and −2 models) 11M57 (−3 and later models)
Down-Flow Additive Base 32K52 32K53
Horizontal Support Frame Kit Ship. Wt. − lbs. (kg.) 56J18 18 lbs. (8 kg)
33K97 − For 2 inch 60L46 − For 3 inch
Concentric Roof/Wall Termination Kits 60G77 − For 1 1/2 inch (38 mm) venting
(51 mm) venting (76 mm) venting
Roof For 2 inch (51 mm) venting 15F75 Not Available
Vent/ Termination
Intake Kits For 3 inch (76 mm) venting Not Available 44J41
Kits 15F74 (ring kit) − 22G44 (close couple) − 30G28 (WTK Close Cou-
Wall For 2 inch (51 mm) venting ple) Not Available
Termination 30G79 (WTKX close couple with extension riser)
Kits
For 3 inch (76 mm) venting Not Available 44J40 (close couple) 81J20 (WTK close couple)
Twinning Kit 15L38 (all models)
Condensate Drain Heat Cable 26K68 6 ft. (1.8 m) 26K69 24 ft. (7.3 m) 26K70 50 ft. (15.2 m)
Heat Cable Tape 39G04 1/2 inch (13 mm) wide or 39G03 2 inch (51 mm) wide
Annual Fuel Utilization Efficiency based on U.S. DOE test procedures and FTC labeling regulations. Isolated combustion system rating for non-weatherized furnaces.
Determine from venting tables proper intake and exhaust pipe size and termination kit required.
Cleanable polyurethane frame type filter.
HIGH ALTITUDE
No gas pressure adjustment is needed when operating from 0 to 4500 ft. (0 to 1372m). See table below for correct manifold
pressure and prove switch for altitudes greater than 4500 ft. (1372m).
Manifold Pressure (outlet) in. w.g. (kPa)

Model No. Prove Switch 4501 to 5500 ft. 5501 to 6500 ft. 6501 to 7500 ft.
(1373 to 1676m) (1677 to 1981m) (1982 to 2286m)
GHR32−50 nat no change 3.5 (0.87) 3.5 (0.87) 3.5 (0.87)
GHR32−75 nat
GHR32−100 nat Kit #67K27 3.4 ((0.85)) 3.3 ((0.82)) 3.2 ((0.80))
GHR32−120 L.P.
GHR32−50 L.P.
no change 10 0 (2.49)
10.0 (2 49) 10 0 (2.49)
10.0 (2 49) 10 0 (2.49)
10.0 (2 49)
GHR32−75 L.P.
GHR32−100 L.P. 10.0 (2.49) 10.0 (2.49) 10.0 (2.49)
Kit #67K27
HGR32−120 L.P. 9.6 (2.39) 9.3 (2.31) 9.0 (2.24)
Page 2
BLOWER PERFORMANCE DATA Q MODELS
GHR32Q2/3-50 BLOWER PERFORMANCE
External Static Air Volume and Motor Watts at Specific Blower Taps
Pressure High Medium-High Medium-Low Low
in. w.g. Pa cfm L/s Watts cfm L/s Watts cfm L/s Watts cfm L/s Watts
0 0 1480 700 640 1330 630 520 1070 505 435 900 425 355
.10 25 1430 675 615 1290 610 500 1050 495 420 880 415 346
.20 50 1380 650 595 1240 585 480 1040 490 400 870 410 330
.30 75 1320 625 570 1200 565 455 1010 475 380 850 400 320
.40 100 1260 595 545 1140 540 430 980 460 370 820 385 300
.50 125 1200 565 520 1080 510 410 930 440 320 790 375 280
.60 150 1100 520 500 1000 470 385 860 405 300 740 350 265
.70 175 1000 470 470 890 420 370 750 355 290 660 310 250
.80 200 800 380 440 700 330 340 590 280 280 550 260 240
NOTE All air data is measured external to unit with air filter in place.
GHR32Q3-75 BLOWER PERFORMANCE

Pressure High Medium-High Medium-Low Low
in. w.g. Pa cfm L/s Watts cfm L/s Watts cfm L/s Watts cfm L/s Watts
0 0 1650 780 720 1540 725 585 1450 685 540 1230 580 450
.10 25 1590 750 660 1490 705 550 1400 660 505 1200 565 420
.20 50 1520 715 645 1430 675 520 1350 635 485 1170 550 405
.30 75 1440 680 630 1370 645 490 1300 615 450 1130 535 390
.40 100 1370 645 610 1300 615 470 1240 585 430 1090 515 370
.50 125 1300 615 590 1240 585 450 1170 550 410 1040 490 330
.60 150 1210 570 560 1170 550 430 1100 520 375 970 460 320
.70 175 1120 530 540 1080 510 410 1020 480 350 890 420 280
.80 200 1020 480 515 980 460 380 900 425 325 750 355 260
.90 225 880 415 500 820 385 350 750 355 300 600 285 240

Pressure High Medium-High Medium Medium-Low Low
in. w.g. Pa cfm L/s Watts cfm L/s Watts cfm L/s Watts cfm L/s Watts cfm L/s Watts
0 0 2530 1195 1360 2300 1085 1210 2030 960 1050 1780 840 885 1540 725 745
.10 25 2460 1160 1290 2250 1060 1140 2010 950 1010 1760 830 850 1530 720 730
.20 50 2380 1125 1270 2200 1040 1100 1990 940 990 1740 820 830 1520 715 720
.30 75 2310 1090 1250 2150 1015 1080 1950 920 970 1720 810 805 1510 715 710
.40 100 2250 1060 1200 2090 985 1060 1910 900 950 1690 800 790 1500 710 690
.50 125 2180 1030 1150 2020 955 1020 1870 880 910 1660 785 780 1480 700 670
.60 150 2100 990 1100 1960 925 980 1810 855 870 1620 765 760 1430 675 650
.70 175 2010 950 1070 1880 885 940 1750 825 855 1570 740 730 1380 650 630
.80 200 1910 900 1040 1800 850 920 1680 795 840 1500 710 710 1320 625 615
.90 225 1800 850 1010 1700 800 890 1580 745 800 1420 670 690 1240 585 600
1.00 250 1700 800 980 1600 755 870 1500 710 780 1320 625 670 1120 530 590

Pressure High Medium-High Medium Medium-Low Low
in. w.g. Pa cfm L/s Watts cfm L/s Watts cfm L/s Watts cfm L/s Watts cfm L/s Watts
0 0 2400 1135 1250 2270 1070 1140 2060 970 1010 1800 850 860 1560 735 720
.10 25 2350 1110 1220 2220 1050 1100 2040 965 980 1780 840 830 1550 730 705
.20 50 2290 1080 1200 2170 1025 1080 2000 945 960 1750 825 815 1540 725 685
.30 75 2220 1050 1180 2120 1000 1060 1960 925 940 1720 810 800 1520 715 675
.40 100 2150 1015 1130 2050 965 1020 1900 895 920 1680 795 770 1500 710 660
.50 125 2080 980 1100 1980 935 980 1850 875 880 1640 775 750 1460 690 650
.60 150 2000 945 1050 1910 900 940 1780 840 840 1590 750 720 1420 670 630
.70 175 1900 895 1010 1830 865 920 1710 805 810 1530 720 690 1380 650 610
.80 200 1800 850 980 1740 820 900 1630 770 790 1460 690 675 1320 625 595
.90 225 1700 800 960 1630 770 860 1540 725 770 1380 650 660 1250 590 580
1.00 250 1600 755 940 1530 720 840 1430 675 750 1300 615 640 1150 545 560
Page 3
SPECIFICATIONS GHR32V MODELS
Model No. GHR32V3-75 GHR32V5-100
High Fire 72,000 (21.1) 100,000 (29.3)

Inp t Bt
Input Btuh
h (kW)
Low Fire 51,000 (14.9) 68,000 (19.9)
High Fire 67,000 (19.6) 93,000 (27.2)

O tp t Btuh
Output Bt h (kW)
Low Fire 47,000 (13.8) 63,000 (18.4)
A.F.U.E. 90.0% 90.0%
California Seasonal Efficiency 83.9 85.3
Exhaust pipe connection (PVC) diameter in. (mm) 2 (51)
Intake pipe connection (PVC) diameter in. (mm) 2 (51)
Condensate drain connection (PVC) in. (mm) 1/2 (12.7)
High Fire 40 − 70 (22 − 39)

Temperature rise
range _F (_C)
Low Fire 35 − 65 (19 − 36)
High static certified by (A.G.A./C.G.A.) in wg. (Pa) .80 (200)
Gas Piping Size I.P.S. in. (mm) 1/2 (12.7)
in. 10 x 8 11-1/2 x 9
Blower wheel nominal
diameter x width
mm 254 x 203 292 x 229
Blower motor output hp (W) 1/2 (373) 1 (746)
Number and size of filters − in. (mm) (1) 14 x 25 x 1 (356 x 635 x 25) (1) 20 x 25 x 1 ( 508 x 635 x 25)
Tons 2 to 3.5 3.5 to 5

Nominal cooling
that can be added
kW 7.0 to 12.3 12.3 to 17.6
Shipping weight lbs. (kg) 1 package 160 (73) 201 (91)
Electrical characteristics 120 volts 60 hertz 1 phase (less than 12 amps)
Optional Accessories (Must Be Ordered Extra)

LPG/Propane kit 59L81
Down-Flow Additive Base 32K52 32K53
Horizontal Support Frame Kit Ship. Wt. − lbs. (kg.) 56J18 18 lbs. (8 kg)
Concentric Roof/Wall Termination Kits 60G77 − For 1 1/2 inch (38 mm) venting 33K97 − For 2 inch (51 mm) venting
Roof For 2 inch (51 mm) venting 15F75

Termination
Kits For 3 inch (76 mm) venting 44J41
Vent/
Intake
Kits 15F74 (ring kit)
22G44 (close couple) 15F74 (ring kit)
Wall For 2 inch (51 mm) venting
30G28 (WTK Close Couple) 22G44 (close couple)
Termination 30G79 (WTKX close couple w/ extension riser)
Kits
For 3 inch (76 mm) venting 44J40 (close couple) 81J20 (WTK close couple)
Condensate Drain Heat Cable 26K68 6 ft. (1.8 m) 26K69 24 ft. (7.3 m) 26K70 50 ft. (15.2 m)
Heat Cable Tape 39G04 1/2 inch (13 mm) wide or 39G03 2 inch (51 mm) wide
Annual Fuel Utilization Efficiency based on U.S. DOE test procedures and FTC labeling regulations. Isolated combustion system rating for non-weatherized furnaces.
Determine from venting tables proper intake and exhaust pipe size and termination kit required.
Cleanable polyurethane frame type filter.
Page 4
BLOWER PERFORMANCE DATA −1 through −3 V MODELS
GHR32V3-75 BLOWER PERFORMANCE
0 through 0.80 in. w.g. (0 Through 200 Pa) External Static Pressure Range
VSP2−1 Blower Control Low Speed 3
Factory Settings High Speed 4
Heat Speed 3
VSP Jumper Speed Positions
ADJUST" LOW" Speed
(Cool, Low Heat Or Continuous Fan) HIGH" Speed (Cool) HEAT" Speed
Jumper
Setting
g 1 2 3 4 1 2 3 4 1 2 3 4
cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s
106 107 127 129 109 128 133
NORM 875 415 940 445 985 465 0 500 0 505 1130 535 0 600 0 610 0 515 1175 555 5 605 0 630
minus 15% 105 109
less motor 750 355 795 375 850 400 915 430 900 425 940 445 5 500 1120 530 940 445 995 470 5 515 1180 555
speed
NOTE The effect of static pressure and filter resistance is included in the air volumes listed.
VSP2−1 Blower Control Low Speed 2
Factory Settings High Speed 4
Heat Speed 1
ADJUST" LOW" Speed (Cool Or Continuous Fan) HIGH" Speed (Cool) HEAT" Speed
Jumper
Setting 1 2 3 4 1 2 3 4 1 2 3 4
cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s
NORM 1100 520 1260 595 1445 680 1635 770 1670 790 1960 925 2165 1020 2285 1075 1640 775 1825 860 2150 1015 2315 1090
minus 15%
less motor 935 440 1015 480 1195 565 1355 640 1335 630 1495 705 1690 800 1800 850 1360 640 1465 690 1770 835 1905 900
speed
NOTE The effect of static pressure and filter resistance is included in the air volumes listed.
BLOWER PERFORMANCE DATA −4 V MODELS
VSP3−1 Blower Control Factory Settings ADJUST − NORM
Heat Speed − 3
Cool Speed − 4
ADJUST"
ADJUST HEAT"
Jumper Low Speed High Speed
P iti
Positions 1 2 3 4 1 2 3 4
cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s cfm L/s
NORM (Normal) 875 415 940 445 985 465 1060 500 1090 515 1175 555 1285 605 1330 630
" (Minus) 15% 750 355 795 375 850 400 915 430 940 445 995 470 1095 515 1180 555
COOL"
ADJUST" Low Speed High Speed
Jumper
Positions 1 2 3 4 1 2 3 4
NORM (Normal) 875 415 940 445 985 465 1060 500 1070 505 1130 535 1270 600 1290 610
" (Minus) 15% 750 355 795 375 850 400 915 430 900 425 940 445 1055 500 1120 530
15% lower motor speed than NORM jumper setting.
NOTE − The effect of static pressure and filter resistance is included in air volumes shown.
NOTE − Continuous Fan only speed is approximately 825 cfm (390 L/s) − non adjustable.
NOTE − Lennox Harmony IIt zone control applications − MAX CFM is determined by COOL jumper placement with a minimum of approximately 875 cfm (415 L/s) for all positions.
GHR32V5−100 BLOWER PERFORMANCE
VSP3−1 Blower Control Factory Settings ADJUST − NORM
Heat Speed − 2
Cool Speed − 4
ADJUST"
ADJUST HEAT"
Jumper Low Speed High Speed
P iti
Positions 1 2 3 4 1 2 3 4
NORM (Normal) 1100 520 1260 595 1445 680 1635 770 1640 775 1825 860 2150 1015 2315 1090
" (Minus) 15% 935 440 1015 480 1195 565 1355 640 1360 640 1465 690 1770 835 1905 900
COOL"
ADJUST" Low Speed High Speed
Jumper
Positions 1 2 3 4 1 2 3 4
NORM (Normal) 1100 520 1260 595 1445 680 1635 770 1670 790 1960 925 2165 1020 2285 1075
" (Minus) 15% 935 440 1015 480 1195 565 1355 640 1335 630 1495 705 1690 800 1800 850
15% lower motor speed than NORM jumper setting.
NOTE − Lennox Harmony IIt zone control applications − MAX CFM is determined by COOL jumper placement with a minimum of approximately 1100 cfm (520 L/s) for all positions.
Page 5
GHR32V3−75−5 Blower Motor Performance
(For Static Pressure 0.0" to 0.8" w.g.)
Blower Speed Adjustment Settings (Switches 5 and 6)
Adjust"
Adjust Cooling
Jumper Low High
Setting
g 1 2 3 4 1 2 3 4
Norm 875 415 940 445 985 465 1060 500 1070 505 1130 535 1270 600 1290 610
– 750 355 795 375 850 400 915 430 900 425 940 445 1055 500 1120 530

Adjust" Heating
Jumper Low High
Setting
g 1 2 3 4 1 2 3 4
Norm 945 446 1025 484 1125 531 1270 599 1080 510 1172 533 1286 607 1452 685
– 803 379 871 411 956 451 1080 510 918 433 996 470 1093 516 1234 582
15% lower motor speed than NORM switch setting.
NOTE − Lennox Harmony IIt zone control applications − MAX CFM is determined by COOL switch setting with a minimum of approximately 875
cfm (415 L/s) for all positions.
GHR32V5−100/125−5 Blower Motor Performance

(For Static Pressure 0.0" to 0.8" w.g.)
Adjust" Cooling
Jumper Low High
Setting 1 2 3 4 1 2 3 4
Norm 1100 520 1260 595 1445 680 1635 770 1670 790 1960 925 2165 1020 2285 1075
– 935 440 1015 480 1195 565 1355 640 1335 630 1495 705 1690 800 1800 850

Adjust"
Heating
Jumper Low High
Setting
g 1* 2 3 4 1* 2 3 4
Norm 1100 520 1260 595 1445 680 1635 770 1640 775 1825 860 2150 1015 2315 1090
– 935 440 1015 480 1195 565 1355 640 1360 640 1465 690 1770 835 1905 900
15% lower motor speed than NORM switch setting.
NOTE − Lennox Harmony IIt zone control applications − MAX CFM is determined by COOL switch setting with a minimum of approximately 1100
cfm (520 L/s) for all positions.
Page 6
SECONDARY LIMIT
GHR32Q−5 PARTS IDENTIFICATION AUTO−RESET
(Downflow Application Shown) (Located on Backside
BACK FILTER
of Blower Wrapper)
CLIP
SURELIGHT TWO−STAGE SUPPLY AIR
INTEGRATED CONTROL BLOWER
TOP CAP
CONTROL VOLTAGE
CIRCUIT BREAKER
CONTROL
BOX
CONTROL TRANSFORMER CABINET
CONTROL BOX COVER

DOOR INTERLOCK SWITCH
COMBUSTION AIR
PROVING (PRES-
COLD END HEADER SURE) SWITCH
(COLLECTOR) BOX
COMBUSTION AIR
BLOWER MOUNTING FLUE
BRACKET COLLAR
COMBUSTION
AIR INDUCER
FRESH AIR
INTAKE FITTING
GASKET
CONDENSATE
CORBELS COLLAR
HOT END HEADER
(COLLECTOR) BOX
EXHAUST TEE
INTAKE AIR
GASKET
PATCH PLATE CONDENSER
WITH BARBED COIL
FITTING PRIMARY LIMIT
AUTO−RESET DuralokPlusTM
(ALTERNATE STYLES) HEAT EXCHANGER
BURNER BOX
ASSEMBLY
TOP
BURNER BOX
BURNER BOX
COVER
GASKET
BURNER BOX
ASSEMBLY
FLAME ROLL−OUT SWITCH
ORIFICE (MANUAL RESET)
FLAME SIGHT
GLASS
CONDENSATE
FLAME SENSOR GAS VALVE
TRAP
IGNITOR AND MANIFOLD
FIGURE 1
Page 7
I−UNIT COMPONENTS INTERIOR MAKE−UP BOX INSTALLATION
GHR32 unit components are shown in figure 1. The com- MAKE−UP
bustion air blower, gas valve and burners can be accessed BOX
by removing the burner access panel. The blower and con-
trol box can be accessed by removing the blower access
door.
J96
WARNING
Before attempting to perform any service or mainte- P96
BUSHING
nance, turn the electrical power to unit OFF at dis-
connect switch
A−Make-Up Box (Figure 2) FIGURE 3

EXTERIOR MAKE−UP BOX INSTALLATION
WARNING
MAKE−UP
Unit must be grounded in accordance with national BOX
and local codes. Electric Shock Hazaed. BUSHING
Can cause injury or death.
A field make−up box (see figure 2) is provided for line voltage

wiring. Line voltage wiring to unit is done through the J96 jack
from the field make−up box to plug P96 from the control box.
J96
The box may be installed inside or outside the unit (see figures (Shown with
3 and 4) and may be installed on the unit left or right side. accessory
wire connected)
P96
MAKE-UP BOX
POWER ENTRY KNOCKOUT
BOX 120V LINE VOLTAGE FIGURE 4
PIGTAIL CONNECTIONS
An accessory (brown) output wire is provided with the make-
up box. The wire provides a 120V connection for optional ac-
COVER
cessories such as electronic air cleaner or humidifier. If
used, the wire is field installed in J96 jack plug by inserting the
pin of the brown wire into the open socket of the jack. See fig-
ure 5. 120V accessories rated up to 4 amps total may be con-
nected to this wire. The neutral INSTALLING BROWN
UNIT leg of the accessory is con- ACCESSORY WIRE TO J96
GROUND WHITE BROWN
nected to the neutral white wire
JACK J96 NEUTRAL
in the make-up box. The acces-
sory terminal is energized
Box may be installed inside or outside unit.
whenever the indoor blower is
FIGURE 2 BLACK
in operation.
J96
FIGURE 5
Page 8
B−Control Box (Figure 6)
ELECTROSTATIC DISCHARGE (ESD) CIRCUIT BREAKER CB8
Precautions and Procedures
CAUTION
PRESS TO RESET
Electrostatic discharge can affect electronic
components. Take precautions during furnace
installation and service to protect the furnace’s FIGURE 7
electronic controls. Precautions will help to avoid
control exposure to electrostatic discharge by
3.Door Interlock Switch (S51)
putting the furnace, the control and the techni- A door interlock switch rated 14 amps at 125VAC is located
cian at the same electrostatic potential. Neutral- on the control box. The switch is wired in series with line
ize electrostatic charge by touching hand and all voltage. When the blower door is removed the unit will shut
tools on an unpainted unit surface, such as the down.
gas valve or blower deck, before performing any
service procedure. DANGER
GHR32−1 through −4 CONTROL BOX Shock hazard.
Disconnect power before servicing. Control is not
TWO−STAGE VSP−2 field repairable. If control is inoperable, simply
CONTROL CONTROL replace entire control.
(v models only) Can cause injury or death. Unsafe operation will
CIRCUIT
BREAKER
result if repair is attempted.
SURELIGHT
4. SureLight Ignition System A92
CONTROL All GHR32−1 through −4 units are equipped with the Len-
nox SureLight ignition system. The system consists of ig-
nitor (figure 8) and ignition control board (figure 9 and
table 3 ). The board and ignitor work in combination to en-
DOOR INTERLOCK sure furnace ignition and ignitor durability. The SureLight
SWITCH
integrated board controls all major furnace operations.
TRANSFORMER
Table 1 and 2 show jack plug terminal designations. shows
FIGURE 6 control board terminations. The board also features two
Unit transformer (T1), circuit breaker (CB8), SureLight LED lights for troubleshooting and two accessory termi-
control (A92), VSP−2 control (A24) and Two−stage control nals rated at (1) one amp. See table 4 for troubleshooting
(A86) are located in the control box. In addition, a door in- diagnostic codes. Units equipped with the SureLight
terlock switch (S51) is located in the control box. Jackplugs board can be used with either electronic or electro−me-
and a snap-off" terminal strip allow the control box to be chanical thermostats without modification. The SureLight
easily removed for blower service. ignitor is made of durable silicon nitride. Ignitor longevity
is also enhanced by voltage ramping by the control board.
1. Control Transformer (T1)
The board finds the lowest ignitor temperature which will
A transformer located in the control box provides power to
successfully light the burner, thus increasing the life of the
the low voltage 24 volt section of the unit. Transformers on
ignitor.
all models are rated 40VA with a 120V primary and a 24V
secondary. NOTE − Do not remove blower access panel to read
Surelight LED lights. A sight glass is provided on the
2. Circuit Breaker (CB8) access panel for viewing.
A 24V circuit breaker is also located in the control box. The
switch provides overcurrent protection to the transformer
(T1). The breaker is rated 3 amps at 32V. If the current ex-
ceeds this limit the breaker will trip and all unit operation will
shut down. The breaker can be manually reset by pressing the
button on the face (figure 7).
Page 9
TABLE 1
SURELIGHT IGNITOR
SureLight BOARD J156 (J2) TERMINAL
5/8" MEASUREMENT IS TO I.D. DESIGNATIONS
OF RETENTION RING
PIN # FUNCTION
1 Ignitor
13/32’
2 Not Used
3 Ignitor Neutral
4 Combustion Air Blower Line Voltage
5 Not Used
FRONT VIEW 6 Combustion Air Blower Neutral
TABLE 2
SureLight BOARD J58 (J1) TERMINAL
DESIGNATIONS
5/16" PIN # FUNCTION

1 Primary Limit In
2 Gas Valve Common
TOP VIEW 3 Roll Out Switch Out
FIGURE 8 4 Gas Valve 24V

5 Pressure Switch In
SURELIGHT INTEGRATED CONTROL BOARD 6 Pressure Switch and Primary Limit Out
GHR32−1 through −4 units
7 Not Used
8 Roll Out Switch In
9 Ground
TABLE 3
TERMINAL DESIGNATIONS
ACB COOL Blower − Cooling Speed (Line Volt)
ACB HEAT Blower − Heating Speed (Line Volt)
PARK Alternate Blower Speeds (Dead)
ACB LOW Continuous Low Speed Blower
ACC Accessory Terminal (Line Volt)
TX 120VAC Hot to Transformer
HOT 120VAC Hot Input
HTG ACC Heat Only Accessory (Line Volt)
NEUTRALS 120VAC Neutrals
24VAC HOT 24VAC Hot from Transformer
24VAC RTN 24VAC Return from Transformer
FLAME SENSE Flame Sense Terminal
FIGURE 9
Page 10
TABLE 4
DIAGNOSTIC CODES
MAKE SURE TO ID LED’S CORRECTLY: REFER TO INSTALLATION INSTRUCTIONS FOR CONTROL BOARD LAYOUT.
LED #1 LED #2 DESCRIPTION

SIMULTANEOUS SIMULTANEOUS Power − Normal operation
SLOW FLASH SLOW FLASH Also signaled during cooling and continuous fan.
SIMULTANEOUS FAST SIMULTANEOUS FAST
FLASH FLASH Normal operation − signaled when heating demand initiated at thermostat.
Primary or Secondary limit open. Limit must close within 3 minutes or board goes
SLOW FLASH ON
into one hour limit Watchguard.
Watchguard pressure switch − 5 minutes. Pressure switch open or has opened 5
times during a single call for heat; OR: Blocked inlet/exhaust vent; OR: Conden-
OFF SLOW FLASH
sate line blocked; OR: Pressure switch closed prior to activation of combustion
air blower.
ALTERNATING SLOW ALTERNATING SLOW
FLASH FLASH Watchguard 60 minute delay − burners fail to ignite.
SLOW FLASH OFF Flame sensed without gas valve energized.

ON SLOW FLASH Rollout switch open. OR: 9 pin connector improperly attached.
ON ON
ON OFF Circuit board failure or control wired incorrectly.
OFF ON
FAST FLASH SLOW FLASH Main power polarity reversed. Switch line and neutral.
SLOW FLASH FAST FLASH Low flame signal. Measures below .61 microAmps. Replace flame sense rod.
ALTERNATING FAST ALTERNATING FAST Improper main ground or line voltage below 75 volts; OR: Broken ignitor; OR:
FLASH FLASH Open ignitor circuit.
NOTE − Slow flash equals 1 Hz (one flash per second). Fast flash equals 3 Hz (three flashes per second). Drop out flame sense current < 0.21 microAmps
a−Electronic Ignition Figures 12 and 13 The SureLight control board has an added feature that pro-
On a call for heat the SureLight control monitors the com- longs the life of the ignitor. After a successful ignition, the
bustion air blower pressure switch. The control will not be- SureLight control utilizes less power to energize the ignitor
gin the heating cycle if the pressure switch is closed (by− on successive calls for heat. The control continues to ramp
passed). Once the pressure switch is determined to be down the voltage to the ignitor until it finds the lowest
open, the combustion air blower is energized. When the amount of power that will provide a successful ignition. This
differential in the pressure switch is great enough, the pres- amount of power is used for 255 cycles. On the 256th call
sure switch closes and a 15−second pre−purge begins. If for heat, the control will again ramp down until the lowest
the pressure switch is not proven within 2−1/2 minutes, the power is determined and the cycle begins again.
control goes into Watchguard−Pressure Switch mode for a b−Fan Time Control Q Models Only
5−minute re−set period. The fan on time of 45 seconds is not adjustable. Fan off
After the 15−second pre−purge period, the SureLight ignitor time (time that the blower operates after the heat demand
warms up for 20 seconds after which the gas valve opens has been satisfied) can be adjusted by flipping the dip
for a 4−second trial for ignition. Units with control 97L48: ig- switches located on the SureLight integrated control. The
nitor stays energized during the trial or until flame is unit is shipped with a factory fan off setting of 90 seconds.
sensed. Units with control 56L83: ignitor stays energized Fan off time will affect comfort and is adjustable to satisfy
for the first second of the 4−second trial. If ignition is not individual applications. See figure 10.
proved during the 4−second period, the control (97L48 or
56L83) will try four more times with an inter purge and
FAN-OFF TIME ADJUSTMENT
warm−up time between trials of 35 seconds. After a total of
five trials for ignition (including the initial trial), the control 60sec. 90sec. 120sec. 180sec.
goes into Watchguard−Flame Failure mode. After a 60−min-
ute reset period, the control will begin the ignition sequence
again.
To adjust fan−off timing, flip dip switch to desired setting.
FIGURE 10
Page 11
c−Flame Sensor 5. Two−Stage Control (A86)
A flame sensor is located on the left side of the burner sup- All GHR32−1 through −4 units are equipped with a two−
port. See figure 11. The sensor is mounted on a bracket in stage control board. Two different boards have been used.
the burner support and the tip protrudes into the flame en- Boards 43K9001 and 29M9201 (figure 14) are identical,
velope of the left−most burner. The sensor is fastened to except the 9 pin connector on 43K9001 is replaced by two
burner supports and can be removed for service without re- relays with quick connect terminals on board 29M9201.
moving any part of the burners. During operation, flame is The two−stage board acts as a go between from the indoor
sensed by current passed through the flame and sensing thermostat to the SureLight ignition board. The board can
be utilized in three modes: with a SINGLE−STAGE thermo-
electrode. The SureLight control allows the gas valve to re-
stat, a TWO−STAGE thermostat or with a second−stage
main open as long as flame signal is sensed.
(high fire) delay called W2 TIMED. The two−stage board is
equipped with a jumper (see figure 14) which changes op-
erating modes and a jumper which adjusts second−stage
SENSOR IGNITOR
heat delay during W2 TIMED mode.
NOTE−The mode of operation jumper on the two−stage

3/8" control board is factory set in the TWO−STAGE" position.
While in the single−stage thermostat mode (one−stage

jumper setting), the unit will always operate on second−
stage heat. The combustion air blower (B6) will operate on
high speed and indoor blower (B3) will operate on heating
speed. While in the two−stage thermostat mode the unit will
operate on first−stage heat (low fire). The combustion air
blower (B6) and indoor blower will operate on low speed.
The unit will switch to second−stage heat (high fire) on call
from the indoor thermostat W2. While in the W2 TIMED
FIGURE 11 mode (factory setting 8 minutes) the unit will fire on first−
stage heat (low fire) with the combustion air blower (B6)
and indoor blower (B3) operating on low speed. After a set
NOTE − The GHR32 furnace contains electronic com- time delay the unit switches to second−stage heat (high
ponents that are polarity sensitive. Make sure that the fire). The combustion air blower and indoor blower also
furnace is wired correctly and is properly grounded. switch to second−stage heat mode.
SureLight Control Ignition Sequence Board 56L8301
ÉÉ 1 15 34 35 38 80 5 SEC
ÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ON Pre −Purge Ignitor Warmup Trial for Blower On" Post
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
OFF Ignition Delay Purge
ÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
DEMAND
CAB
ÉÉÉÉÉÉÉÉÉÉ
IGNITOR
GAS VALVE
INDOOR BLOWER
*Blower on time will be 45 seconds after gas valve is energized. Blower off time will depend on OFF TIME" Setting.
FIGURE 12
ÉÉ
SureLight Control Ignition Sequence Board 97L4801
1 15 34 38 80 5 SEC
ÉÉ ON Trial for Blower On"
ÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
Pre −Purge Ignitor Warmup Ignition Post
Delay Purge
OFF
DEMAND
ÉÉÉÉÉÉÉÉÉ
CAB
IGNITOR
ÉÉÉÉÉÉÉÉÉ
GAS VALVE
INDOOR BLOWER
*Blower on time will be 45 seconds after gas valve is energized. Blower off time will depend on OFF TIME" Setting.
FIGURE 13
Page 12
TWO−STAGE CONTROL BOARD
6.VSP2−1 Blower Control Board (A24)
G32(V) −1 through −4 units −1 through −3 V Models only
GHR32V−1 through −3 units are equipped with a variable
speed motor that is capable of maintaining a specified CFM
throughout the external static range. The unit uses the
VSP2−1 variable speed control board, located in the blow-
W2 TIMED
DELAY JUMPER er compartment, which controls the blower speed and
provides diagnostic LEDs. The control has a non−adjust-
MODE OF able, factory preset ON" fan timing delay and an adjustable
OPERATION
JUMPER OFF" fan timing delay (see figure 17).
The VSP2−1 also senses limit trip condition and turns on the
blower. The GHR32 primary limit switch is located in the
middle of the vestibule wall and the secondary limit switch is
located int ehblower compartment. When excess heat is
sensed in the heat exchanger, or blower compartment,
the respective switch will open and interrupt the current to
the gas valve, while at the same time the VSP2−1 energizes
the blower on heating speed. The limit automatically resets
when the unit temperature returns to normal and the blower is
de−energized.
FIGURE 14 Diagnostic LEDs located on the VSP2−1 control board are pro-
vided to aid in identifying the unit’s mode of operation. Certain
scenarios will arise depending on the jumper positions. Refer
to figure 15 for identification.
VSP2−1 VARIABLE SPEED CONTROL BOARD SELECTIONS
JP
JP46
2 13 PIN PLUG
HIGH SPEED HIGH LOW ADJUST HEAT
(BOARD TO MOTOR)
SELECTOR PINS
(COOLING ONLY) 1 1 TEST 1 HEATING SPEED
2 2 − 2 SELECTOR PINS
3 3 + 3 See table 5 for VSP2
4 4 NORM 4 factory settings
LOW SPEED
SELECTOR PINS HTG.
HEAT DS3 HI/LOW DS4
(COOLING, HEATING and BLOWER OPERATIONAL
CONTINUOUS FAN) SELECTOR PINS
(Affects both heating and
1 2 DS2 ON/OFF DS1 CFM
cooling modes)
HEATING STAGE
JUMPER SELECTOR PINS DIAGNOSTIC
DS LEDS
210
270
90
JP73
15 PIN PLUG
(BOARD TO VARIOUS 150
POINTS IN FURNACE) JP
1 FAN OFF"
1 TIMING PINS
FIGURE 15
Page 13
VSP2−1 BLOWER CONTROL BOARD (A24)
IMPORTANT
1
24 VAC half wave rectified (DC pulse), when mea- J46
sured with a meter, may appear as a lower or higher
voltage depending on the make of the meter. Rather HIGH LOW ADJUST HEAT
than attempting to measure the output voltage of the 1 1 TEST 1

VSP2 board, see GHR32 BLOWER & VSP2 BLOWER 2 2 − 2
3 3 + 3
CONTROL BOARD TROUBLESHOOTING FLOW
4 4 NORM 4
CHART in the TROUBLESHOOTING section of this
manual. HTG.
BLOWER HEAT DS3 HI/LOW DS4
Diagnostic LED Lights

210
a − DS3 ON/OFF"
270
90
150
ON/OFF−DS3 indicates there is a demand for the blower mo-
J73
tor to run. When the ON/OFF LED−DS3 is lit, a demand is be-
1
ing sent to the motor. In heating mode only, there is a 45 sec- J73
ond fan ON" delay in energizing ON/OFF LED−DS3. PIN 1 - C - 24 VAC common.
PIN 2 - G - Input signal from thermostat’s fan signal.
The light will not go off until adjustable fan OFF" delay PIN 3 - W2 - Input signal for second stage heat from the thermostat.
PIN 4 - DS - Input signal for the blower speed regulation.
has expired. PIN 5 - Limit - Input signal from the external limit.
PIN 6 - R - 24 VAC power to the thermostat.
PIN 7 - C - 24 VAC common.
If ON/OFF LED−DS3 is on and both HIGH/LOW LED−DS1 & Pin 8 - C - 24 VAC common.
PIN 9 - CI - Input signal from the fan limit control.
HEAT LED−DS2 are off, the motor will operate in low PIN 10 - CO - Output signal to the burner control.
PIN 11 - HT - Input signal from the fan limit control.
speed. PIN 12 - ACC - 24 VAC accessory output.
PIN 13 - 24V - Input 24 VAC power for the VSP2-1.
b − DS2 HEAT" PIN 14 - 24V - Input 24 VAC power for the VSP2-1.
PIN 15 - V - Input signal from the gas line.
If HEAT LED−DS2 is on, the blower is running in the heat J46

PIN 1 - Heat - Heat speed input signal to the ICM2 motor.
speed according to the HEAT" jumper setting. The HEAT PIN 2 - C - 24 VAC common.
LED−DS2 comes on instantaneous and switches off when PIN 4 - High Tap - High Speed programming input.
PIN 5 - Low Tap - Low speed programming input.
the call for heat is satisfied. PIN 6 - On / Off - On / off output signal to the ICM2 motor.
PIN 7 - Adjust Tap - ICM2 mode selection.
NOTE−When the blower is in OFF" delay mode, the mo- PIN 8 - Hi / Low - Speed regulate input signal to the ICM2 motor.
PIN 9 - Hi / Low - Speed regulate input signal to the ICM2 motor.
tor runs at low speed, therefore the HEAT LED−DS2 is off. It PIN 10 - Ref. V - ICM2 reference voltage.
PIN 11 - Heat Tap - Heating blower speed programming.
switches off when the call for heat is satisfied. PIN 12 - C - 24 VAC common.
PIN 13 - cfm - Motor speed diagnostic signal.
c − DS1 HI/LOW"
HIGH/LOW LED−DS1 indicates whether the blower is op-
VOLTAGES INTO VSP2−1
erating in high or low speed. When the light is off, the blow-
Voltage across J73 pins 13 to 1 and 6 to 1 is 24VAC as shown here.
er is running in low speed according to the LOW" jumper Refer to unit wiring diagram.
24VAC @ 60Hz.
setting. When HIGH/LOW LED−DS1 is on, the blower is op-
34 volts
erating in high speed according to the HIGH" jumper set-
0 volts
ting.
−34 volts
d − DS4 CFM" Voltage across J73 pins 4 to 1 is approximately 15-20VDC (straight voltage) if CCB
is used. If Harmony is used a voltage of 0−25VDC should be present.
CFM LED−DS4 indicates the CFM the unit is operating, If CCB or Harmony is not used, pin 4 to 1 voltage is 21VAC.
according to the jumper settings. The light flashes once

for approximately every 100 CFM. For example, if the unit VOLTAGES FROM VSP2−1 TO ELECTRONICALLY
CONTROLLED BLOWER MOTOR
is operating at 1000 CFM, CFM LED−DS4 will flash 10 Voltage across J46 pins 6 to 3 and 1 to 3 is half-rectified AC as shown here.
times. If the CFM is 2050, CFM LED−DS4 will flash 20 full Refer to unit wiring diagram.
24VAC Half-Rectified (DC Pulse)
times plus one fast or half flash. @ 60Hz.
Approx.
At times the light may appear to flicker or glow. This takes 34 volts
place when the control is communicating with the motor be- 0 volts
tween cycles. This is normal operation. Voltage across J46 pins 8 and 9 to 3, is approximately 15-20VDC if CCB is used. If CCB or
Harmony is not used, pins 8 and 9 to 3 voltage is approximately 21VAC. If Harmony is used
The appropriate speed according to application and CFM a voltage of 0−25VDC should be present.
need is selected by moving jumper pins. FIGURE 16
Page 14
NOTE−On Harmony II zoning applications in the heating not operable. Notice in the GHR32V5−100 table, that the
mode, the highest speed obtainable is the same as the highest normal adjustment setting for heat speed position #3 is
cooling speed selection. Also, the heating speed (heat jumper 2150 CFM (1015L/s). After the adjustment setting has been
position) is only used when the primary limit has been tripped. determined, chose the remaining speed jumper settings
In non−zoning applications, refer to the section on the VSP2−1 from those offered in the table.
control. The TEST pin is available to bypass the VSP2−1 control and
run the motor at approximately 70% to test that the motor is
Jumper Settings operational. This is beneficial primarily in troubleshoot-
SEE BLOWER PERFORMANCE TABLES AT FRONT ing. G must be energized for motor to run.
OF MANUAL FOR ANY REFERENCE TO CFM. b−HEATING BLOWER"
For GHRV32 units, place the HEATING BLOWER jumper
IMPORTANT across the second and third pins (position #2).
Before changing jumper setting, make sure the
motor has completely stopped. Any jumper set- When W1 is energized, the LOW jumper selections are ac-
ting change will not take place while the motor tivated. The HEAT jumper selections are activated when
is running. W2 is energized.
NOTE−In Harmony II zoning applications, HEATING
To change jumper positions, gently pull the jumper off the pins BLOWER jumper must be in position #2.
and place it on the desired set of pins. The following section
c−HEAT"
outlines the different jumper selections available and condi-
tions associated with each one. Refer to figure 15 for identifica- The HEAT jumper is used to set the blower speed to ob-
tion. tain the required CFM as outlined in HEAT SPEED in the
blower performance tables.
After the CFM for each application has been determined, the
jumper settings must be adjusted to reflect those given in The HEAT jumper selections are activated with a call for
the tables in the blower performance section. Using the tables, second-stage heating (W2).
determine which row of CFM volumes most closely d−HIGH"
matches the desired CFM. Once a specific row has been
The HIGH jumper is used to determine the CFM during
chosen (NORMAL or −), CFM volumes from other rows
cooling speed. These jumper selections are activated
cannot be used. Below are the descriptions of each of the
when G and DS terminals are energized.
jumper selections.
e−LOW"
Refer to table 5 for factory settings. Refer to the blower perfor-
The LOW jumper is used to determine CFM during low
mance tables for the approximate air volume for each setting.
speed cooling. These jumper selections are activated
TABLE 5 when G is energized. The LOW jumper may also be used for
VSP2−1 FACTORY SETTINGS
low speed heating. See the HEAT" section for details.
MODEL HIGH LOW ADJUST HEAT
f−FAN OFF"
GHR32V−75−
4 3 NORM 2
1, −2, −3 units Fan OFF" timings (time that the blower operates after the
GHR32V−100 heat demand has been satisfied) are determined by the ar-
−1, −2, −3 4 2 NORM 1 rangement of a jumper on the VSP2−1 board. See figure
units 17. To adjust fan OFF" timings, gently disconnect the
jumper and reposition it across pins corresponding with the
a−ADJUST" new timing. Fan OFF" time is adjustable from 90 to 330
The ADJUST pins allow the motor to run at normal speed or seconds. The control has a non−adjustable, factory preset
approximately 15% lower than normal speed. The blower on" fan timing (45 seconds).
performance tables give two rows (NORMAL and −) with WARNING − MAKE SURE TO DISCONNECT POWER
their respective CFM volumes. The + adjustment setting is BEFORE CHANGING FAN OFF" TIMINGS.
Page 15
NOTEIf fan OFF" time is too low, residual heat in heat
FAN-OFF TIME ADJUSTMENT
exchanger may cause primary limit S10 to trip resulting
TIMING in frequent cycling of blower. If this occurs, adjust blow-
To adjust fan−off timings:
JUMPER
Remove jumper from VSP2−1 and select er to longer time setting.
one of the other pin combinations to
achieve the desired time. Table 6 outlines the operation of the variable speed motor
in relation to specific modes of operation. Some informa-
270 210 Leave jumper off to achieve tion has been repeated from the previous section to provide
330 second fan−off timing.
an example. Refer to each diagnostic LED or jumper settings
TIMING PINS (seconds)
section for more information.
Fan-off timing is factory
set at 90 seconds
150 90
FIGURE 17
TABLE 6
VSP2−1 GHR32−1 through −3 units OPERATION
HEATING MODE COOLING MODE
UNITS WITH UNITS WITH UNITS WITH SINGLE− UNITS WITH TWO−SPEED
SINGLE−STAGE HEATING TWO−STAGE HEATING SPEED COMPRESSOR COMPRESSOR
NON−ZONED NON−ZONED NON−ZONED NON−ZONED
APPLICATIONS APPLICATIONS APPLICATIONS APPLICATIONS
Using a single−stage thermostat with Using a two−stage thermostat with The terminals DS and Y must be The ON/OFF LED−DS3 is lit to indicate
one−stage" heating, the HEAT LED− first−stage (W1) calling, the ON/OFF jumpered together. With a call for the blower is operating in first stage
DS2 is lit when the thermostat calls for LED−DS3 is lit to indicate the blower is cooling, terminals G, Y and DS on the cooling. This LED is energized on
heat. The ON/OFF LED−DS3 is lit after operating in low speed. unit control board are energized from when a 24VAC thermostat demand is
110 seconds (65 seconds pre−purge the thermostat. HI/LOW LED−DS1 supplied to the control (terminal G" on
When the ON/OFF LED−DS3 and
and 45 seconds fan ON" time) from and ON/OFF LED−DS3 are lit to indi- the control board terminal strip).
HEAT LED−DS2 are lit, the blower is
the time a call for heat is made. This in- cate the blower is operating on high
operating in heating speed and sec- In second stage, the ON/OFF LED−
dicates the blower is operating in heat- speed.
ond−stage (W2) heating is calling. DS3 and HI/LOW LED−DS1 are lit to
ing speed.
HEAT LED−DS2 is lit with a call for heat NOTEY and DS are factory jump- indicate the blower is operating on
Using a single−stage thermostat with ered for single−stage cooling, non− high speed (24VAC is supplied to the
from the thermostat. ON/OFF LED−
W2 TIMED," and W1 calling, the ON/ zoned applications. unit terminal strip Y2 from Y2 on the
DS3 is lit after 110 seconds from the
OFF LED−DS3 is lit to indicate the thermostat).
time a call for heat is made. NOTEFor low speed during single−
blower is operating on low speed. NOTE Jumper must be moved from
stage cooling remove jumper from Y
When the HEAT LED−DS2 is lit, the Y1 to Y2 In two−speed, non−zoned ap-
blower is operating in heating speed, to DS.
plications.
and second−stage (W2) heating is call-
ing.
HARMONY ZONED HARMONY ZONED HARMONY ZONED HARMONY ZONED
APPLICATIONS APPLICATIONS APPLICATIONS APPLICATIONS
The blower speed is controlled by the The blower speed is controlled by the The blower speed is controlled by the The blower speed is controlled by the
PWM (pulse width modulation) signal PWM (pulse width modulation) signal PWM (pulse width modulation) signal PWM (pulse width modulation) signal
sent from the control center of the zon- sent from the control center of the zon- sent from the control center of the sent from the control center of the zon-
ing system to the terminal strip’s DS ing system to the terminal strip’s DS zoning system to the terminal strip’s ing system to the terminal strip’s DS
terminal. HI/LOW LED−DS1 and ON/ terminal. HI/LOW LED−DS1 and ON/ DS terminal. HI/LOW LED−DS1 and terminal. HI/LOW LED−DS1 and ON/
OFF LED−DS3 are lit to indicate the OFF LED−DS3 are lit to indicate the ON/OFF LED−DS3 are lit to indicate OFF LED−DS3 are lit to indicate the
blower is operating. blower is operating.
the blower is operating. blower is operating.
NOTE−In Harmony II zoning applica- NOTE−In Harmony II zoning applica-
tions, HTG. BLOWER jumper must be tions, HTG. BLOWER jumper must be
in position #2. in position #2.
NOTE: For zone applications with Harmony, remove the wire from the pin #3 of the J73 terminal on the VSP control board, insulate the
end, and secure it to prevent from shorting.
Page 16
7.VSP3−1 Blower Control Board (A24) The VSP3−1 also senses limit trip condition and turns on the
GHR32V−4 Units blower. The GHR32V limit switch is located in the middle of the
GHR32V−4 units are equipped with a variable speed motor vestibule wall. When excess heat is sensed in the heat ex-
that is capable of maintaining a specified CFM throughout changer, the limit switch will open and interrupt the current
the external static range. The unit uses the VSP3−1 vari- to the gas valve, while at the same time the VSP3−1 energizes
able speed control board, located in the blower compart- the blower on heating speed. The limit automatically resets
ment, which controls the blower speed and provides when the unit temperature returns to normal and the blower is
diagnostic LEDs. The control has both a non−adjustable, de−energized.
factory preset ON" fan timing delay and an adjustable OFF" Diagnostic LEDs located on the VSP3−1 control board are pro-
fan timing delay (see figure 17). vided to aid in identifying the unit’s mode of operation. Certain
scenarios will arise depending on the jumper positions. Refer
to figure 18 for identification.
VSP3−1 VARIABLE SPEED CONTROL BOARD SELECTIONS
JP2
JP46
13 PIN PLUG
DELAY PROFILE DELAY COOL ADJUST HEAT
(BOARD TO MOTOR)
SELECTOR PINS
(COOLING ONLY) 1 1 TEST 1 HEATING SPEED
2 2 − 2 SELECTOR PINS
3 3 + 3 See table 7 for VSP3−1
4 4 NORM 4 factory settings
COOL SPEED
SELECTOR PINS HTG.
HEAT DS3 HI/LOW DS4
(COOLING, HEATING and BLOWER OPERATIONAL
CONTINUOUS FAN) SELECTOR PINS
(Affects both heating
and cooling modes)
HEATING STAGE
JUMPER SELECTOR PINS DIAGNOSTIC
DS LEDS
210
270
90
JP73
15 PIN PLUG
(BOARD TO VARIOUS 150
POINTS IN FURNACE) JP1
FAN OFF"
1 TIMING PINS
FIGURE 18
Page 17
VSP3−1 BLOWER CONTROL BOARD (A24) IMPORTANT
1
J46 24 VAC half wave rectified (DC pulse), when

measured with a meter, may appear as a lower
DELAY COOL ADJUST HEAT
or higher voltage depending on the make of the
1 1 TEST 1
2 2 − 2
meter. Rather than attempting to measure the
3 3 + 3 output voltage of A24, see GHR32V BLOWER &
4 4 NORM 4 VSP3 BLOWER CONTROL BOARD TROUBLE-
SHOOTING FLOW CHART in the TROUBLE-
HTG.
BLOWER HEAT DS3 HI/LOW DS4 SHOOTING section of this manual.
1 2 DS2 ON/OFF DS1 CFM Diagnostic LED Lights

DS3 ON/OFF
210 ON/OFF−DS3 indicates there is a demand for the blower
270
motor to run. When the ON/OFF LED−DS3 is lit, a demand
90
150 is being sent to the motor. In heating mode only, there is a
J73 45−second fan ON" delay in energizing ON/OFF LED−
1 DS3. Light will not go off until adjustable fan OFF" delay
J73 has expired.
PIN 2 - G - Input signal from thermostat’s fan signal. If ON/OFF LED−DS3 is on and both HIGH/LOW LED−DS1
PIN 3 - W2 - Input signal for second stage heat from the thermostat.
PIN 4 - DS - Input signal for the blower speed regulation. & HEAT LED−DS2 are off, the motor will operate in low
PIN 5 - Limit - Input signal from the external limit.
PIN 6 - R - 24 VAC power to the thermostat. speed (heating).
Pin 8 - C - 24 VAC common. DS2 HEAT
PIN 9 - CI - Input signal from the fan limit control.
PIN 10 - CO - Output signal to the burner control. If HEAT LED−DS2 is on, the blower is running in second−
PIN 11 - HT - Input signal from the fan limit control. stage heat speed according to the HEAT" jumper setting.
PIN 12 - ACC - 24 VAC accessory output.
PIN 13 - 24V - Input 24 VAC power for the VSP2-1. In heating mode only, there is a 45 second delay in energiz-
PIN 14 - 24V - Input 24 VAC power for the VSP2-1.
PIN 15 - V - Input signal from the gas line. ing HEAT LED−DS2. Light will not go off until adjustable fan
J46 OFF" delay has expired.
PIN 1 - Not Used.
PIN 2 - C - 24 VAC common. DS1 HI/LOW
PIN 3 - C - 24 VAC common. HIGH/LOW LED−DS1 indicates the blower is operating in
PIN 4 - Delay Tap - Delay profile programming input.
PIN 5 - Cooling blower speed programming input. the cooling mode.
PIN 6 - On / Off - On / off output signal to the ICM2 motor.
PIN 7 - Adjust Tap - ICM2 mode selection. DS4 CFM
PIN 8 - NOT USED
PIN 9 - Hi / Low - Speed regulate input signal to the ICM2 motor with CCB1 and
CFM LED−DS4 indicates the CFM the blower is providing,
HARMONY only
PIN 10 - Ref. V - ICM2 reference voltage.
according to the jumper settings.
PIN 11 - Heat Tap - Heating blower speed programming.
PIN 13 - cfm - Motor speed diagnostic signal.
VOLTAGES INTO VSP3−1

Voltage across J73 pins 13 to 1 and 6 to 1 is 24VAC as shown here.
Refer to unit wiring diagram.
24VAC @ 60Hz.
34 volts
0
volts
−34 volts
Voltage across J73 pins 4 to 1 is approximately 15-20VDC (straight voltage)

if CCB is used. If Harmony is used a voltage of 0−25VDC should be present.
If CCB or Harmony is not used, pin 4 to 1 voltage is 21VAC.
VOLTAGES FROM VSP3−1 TO ELECTRONICALLY

CONTROLLED BLOWER MOTOR
Voltage across J46 pins 6 to 3 and 1 to 3 is half-rectified AC as shown here.
Refer to unit wiring diagram.
24VAC Half-Rectified (DC
Pulse)
Approx. @ 60Hz.
34 volts
0
volts
Voltage across J46 pin 9 to 3 is approximately 15-20VDC if CCB is used. If CCB or
Harmony is not used, pin 9 to 3 voltage is approximately 21VAC. If Harmony is used
a voltage of 0−25VDC should be present.
FIGURE 19
Page 18
Jumper Settings HTG. BLOWER
For GHR32V−4 units only, place the HTG. BLOWER jump-
SEE BLOWER PERFORMANCE TABLES AT FRONT
er across the second and third pins (position #2).
OF MANUAL FOR ANY REFERENCE TO CFM.
NOTE − In Harmony II zoning applications, HTG. BLOWER
jumper must be in position #2.
IMPORTANT HEAT
Before changing jumper setting, make sure the
motor has completely stopped. Any jumper set- The HEAT jumper is used to set the blower speed to obtain
ting change will not take place while the motor the required CFM as outlined in HEAT SPEED section of
is running. the blower performance tables. The HEAT jumper selec-
tions are activated with a call for first−stage heating (W1)
To change jumper positions, gently pull the jumper off the pins and second−stage heating (W2).
and place it on the desired set of pins. The following section
DELAY
outlines the different jumper selections available and condi-
tions associated with each one. Refer to figure 18 for identifica- The DELAY jumper is used to set the specific motor fan
tion. mode of operation during cooling. Depending on the ap-
plication, one of four fan options may be chosen by moving
After the CFM for each application has been determined, the
the jumper to the appropriate set of pins.
jumper settings must be adjusted to reflect those given in
the blower performance tables. Using the tables, determine Options 1, 2, 3, or 4 will have an increased dehumidification
which row of CFM volumes most closely matches the effect on the system. Option 1 will have the least effect and
desired CFM. Once a specific row has been chosen option 4 will have the greatest effect.
(NORMAL or −), CFM volumes from other rows cannot be
used. Below are the descriptions of each of the jumper #1 PIN JUMPERED
selections. A − Motor runs at 100% until demand is satisfied.
B − Once demand is met, motor ramps down to off.
Refer to table 7 for factory settings. A B
TABLE 7
100% CFM
VSP FACTORY SETTINGS FOR GHR32V−4 UNITS OFF OFF
COOLING
MODEL DELAY COOL ADJUST HEAT DEMAND
GHR32V3−75 4 4 NORM 3 #2 PIN JUMPERED

A − Motor runs at 82% for approximately 7−1/2 minutes.
GHR32V5−100 4 4 NORM 2
B − If demand has not been satisfied after 7−1/2 minutes,
NOTE − In Harmony II zoning applications in the heating mode, the motor runs at 100% until demand is satisfied.
the highest cooling speed selected is the highest blower speed C − Once demand is met, motor ramps down to off.
obtainable. Also, the fan−only speed is used when the primary lim- B C
A
it has been tripped. In non−zoning applications, refer to the section 7 1/2 MIN
on the VSP3−1 control. 100% CFM
OFF 82%CFM OFF
ADJUST COOLING DEMAND
The ADJUST pins allow the motor to run at normal speed

or approximately 15% lower than normal speed. The blow- #3 PIN JUMPERED
er performance tables two rows (NORMAL and −) with their A − Motor runs at 50% for 1/2 minute.
respective CFM volumes. The + adjustment setting is not B − Motor then runs at 82% for approximately 7−1/2 min-
operable. Notice that the normal adjustment setting for utes.
C − If demand has not been satisfied after 7−1/2 minutes,
heat speed position #3 is 2150 CFM (1015 L/s) . After the
motor runs at 100% until demand is satisfied.
adjustment setting has been determined, choose the re-
D − Once demand is met, motor ramps down to off.
mainder speed jumper settings from those in the table.
B C D
The TEST pin is available to bypass the VSP3−1 control and A 7 1/2 MIN
run the motor at approximately 70% to test that the motor is OFF 82% CFM
100% CFM OFF
1/2 MIN
operational. This is beneficial primarily in troubleshooting. G 50% CFM
COOLING DEMAND
must be energized for motor to run.
Page 19
#4 PIN JUMPERED COOL
A − Motor runs at 50% for 1/2 minute. The cool jumper is used to set the blower speed to obtain
B − Motor then runs at 82% for approximately 7−1/2 min- the required CFM as outlined in the blower performance
utes. tables.
C − If demand has not been satisfied after 7−1/2 minutes, VSP Operation
motor runs at 100% until demand is satisfied. Table 8 outlines the operation of the variable speed motor
D − Once demand is met, motor runs at 50% for 1/2 min- in relation to specific modes of operation. See table 9 for
ute. GHR32V with CCB1 and a two speed outdoor unit. Some
E − Motor ramps down to off.
C D information has been repeated from the previous section to
B
A E provide an example. Refer to each diagnostic LED or jump-
7 1/2 MIN 100%
OFF 82% CFM CFM OFF er settings section for more information.
1/2 MIN 1/2 MIN
50% CFM 50% CFM
COOLING DEMAND
TABLE 8
GHR32V−4 Units with VSP3−1
Heating Mode Cooling Mode
Units With Units With Units With Units With
Single−Stage Heating Two−Stage Heating Single−speed Compressor Two−speed Compressor
Non−Zoned Applications Non−Zoned Applications Non−Zoned Applications Non−Zoned Applications
Using a single−stage thermostat Using a two−stage thermostat with Y1−DS and Y1−Y2 must be jump- Y1−DS must be jumpered together.
with "one−stage" heating, the HEAT first−stage (W1) calling, the ON/ ered together. With a call for cool- With a call for single−stage cooling,
LED−DS2 is lit when the thermostat OFF LED−DS3 is lit to indicate the ing, G, Y1, Y2 and DS on the unit G, Y1, and DS on the unit control
calls for heat. The ON/OFF LED− blower is operating in low speed control board are energized from board are energized from the Ther-
DS3 is lit after 110 seconds (65 sec- heat. the thermostat. HI/LOW LED−DS1 mostat. With a call for second−stage
onds prepurge and 45 seconds fan and ON/OFF LED−DS3 are lit to in- cooling, G, Y1, Y2, and DS on the
"ON" time) from the time a call for When the ON/OFF LED−DS3 and dicate a call for cooling. unit control board are energized
heat is made. This indicates the HEAT LED−DS2 are lit, the blower from the thermostat. In both cases,
blower is operating in high speed is operating in high speed heat and Note − Y1 to DS and Y1 to Y2 are HI/LOW LED−DS1 and ON/OFF
heat. second−stage (W2) is calling. factory jumpered for single−stage LED−DS3 are lit to indicate a call for
Using a single−stage thermostat cooling, non−zoned applications. cooling.
with "W2 TIMED" and W1 calling, HEAT LED−DS2 is lit with a call for
the ON/OFF LED−DS3 is lit to indi- heat from the thermostat. ON/OFF
LED−DS3 is after 110 seconds from Note − Jumper Y1−Y2 must be re-
cate the blower is operating on low moved for units with two−speed
speed heat. the time a call for heat is made.
compressor.
When HEAT LED−DS2 is lit, the
blower is operating in high speed
heat and second−stage (W2) is call-
ing.
Harmony Zoned Applications Harmony Zoned Application Harmony Zoned Application Harmony Zoned Application
The blower speed is controlled by The blower speed is controlled by The blower speed is controlled by The blower speed is controlled by
the PWM (pulse width modulation) the PWM (pulse width modulation) the PWM (pulse width modulation) the PWM (pulse width modulation)
signal sent from the control center signal sent from the control center signal sent from the control center signal sent from the control center
of the zoning system to the terminal of the zoning system to the terminal of the zoning system to the termi- of the zoning system to the terminal
strip’s DS terminal. HI/LOW LED− strip’s DS terminal. HI/LOW LED− nal strip’s DS terminal. HI/LOW strip’s DS terminal. HI/LOW LED−
DS1 and ON/OFF LED−DS3 are lit DS1 and ON/OFF LED−DS3 are lit LED−DS1 and ON/OFF LED−DS3 DS1 and ON/OFF LED−DS3 are lit
to indicate the blower is operating. to indicate the blower is operating.
are lit to indicate the blower is oper- to indicate the blower is operating.
Note − In Harmony II zoning ap- Note − In Harmony II zoning applica- ating.
plications, HTG BLOWER jumper tions, HTG BLOWER jumper must
must be in position #2. be in position #2.
NOTE − For zone applications with Harmony, remove the wire from pin #2 and pin #13 of the J49 terminal at the motor and the wire
from pin #3 of the J73 terminal on the VSP control board, insulate the ends and secure to prevent shorting.
Page 20
TABLE 9
GHR32V−4 UNITS WITH CCB1 & TWO−SPEED OUTDOOR UNIT OPERATING SEQUENCE
Operating Sequence System Demand System Response

System Thermostat *Relative Humidity ***Compressor Blower CFM
Step Comments
Condition Demand (EfficiencyPlus Lights) Speed (COOL)
55% of
1 Y1 Acceptable (None) Low Compressor demand and indoor
HIGH COOL
Normal operation blower speed follow thermostat
2 Y2 Acceptable (None) High HIGH COOL demand
55% of
1 Y1 Acceptable (None) Low
HIGH COOL
Call for humidity Change to slightly 55% of

2 Y1 Low Dehumidification mode begins with
removal during 1st over setpoint (1) HIGH COOL
next thermostat demand,
demand after initial
stage thermostat Demand
3 Slightly over setpoint (1) Off Off thermostat demand is satisfied.
demand satisfied
**77%/74% of
4 Y1 Slightly over setpoint (1) High
HIGH COOL
55% of If humidity increases significantly
1 Y1 Acceptable (None) Low over setpoint, or if slide switch is
Significant increase HIGH COOL
in humidity during moved significantly,
significantly unit will immedi-
thermostat demand. Change to significantly **77%/74% of ately go into dehumidification mode
2 Y1 High
over setpoint (2 or more) HIGH COOL (in presence of thermostat demand).
**77%/74% of
1 Y1 Over Setpoint High
HIGH COOL
When humidity demand is satisfied,
Change to Acceptable blower immediately shifts to the
Humidity demand 2 Y1 High HIGH COOL
(None) HIGH COOL CFM in order to hasten
satisfied during
the end of the cycle.
cycle Unit can only
thermostat demand. 3 None Acceptable (None) Off Off shift out of high
g speed
p compressor
p
55% of operation
ti att bbeginning
i i off nextt cycle.
l
4 Y1 Acceptable (None) Low
HIGH COOL
1 Y2 Acceptable (None) High HIGH COOL
Call for humidity
removal during 2nd Change to slightly **77%/74% of Blower immediately changes speed
2 Y2 High
stage
g thermostat over setpoint (1) HIGH COOL in response to thermostat demand.
demand
3 Y2 Acceptable (None) High HIGH COOL
1 None Slightly over setpoint (1) Off Off Dehumidification mode (high speed
*Call
Call for 1st stage
compressor) begins with next ther-
ther
cooling after call for 55% of
2 Y1 Slightly over setpoint (1) Low mostat demand after initial demand is
humidity removal. HIGH COOL satisfied.
Call for 2nd stage 1 None Slightly over setpoint (1) Off Off Reduced blower speed (dehumidifi-
cooling after call for **77%/74% of cation speed) begins immediately
humidity removal 2 Y2 Slightly over setpoint (1) High with thermostat demand
HIGH COOL
Significantly over setpoint If humidity increases significantly
1 None Off Off
Call for cooling after (2 or more) over setpoint, or if slide switch is
significant increase moved unit immediately goes into
moved,
in humidity Significantly over **77%/74% of dehumidification mode (in presence
2 Y1 or Y2 High
setpoint (2 or more HIGH COOL of thermostat demand).
Humidity demand 1 None Over setpoint (1 or more) Off Off While unit is not operating (no ther-
satisfied between mostat demand), slide switch is
thermostat demands moved down and back up. Blower
Change to
(unit off cycle). 2 Y1 or Y2 High HIGH COOL and compressor operate at high
acceptable (None)
speed until next thermostat demand.
Note − When changing unit mode of operation from cooling to heating, indicating lights that are on will stay on until the first ther-
mostat heating demand.
*IMPORTANT - If power to unit is turned on with CCB1 calling for humidity removal, outdoor unit may be locked into high speed
indefinitely. To reset, move humidity slide switch all the way down then back up to desired setpoint (with unit running)
** Reduced blower speed is 77% of COOL for the V3 units; 74% of COOL for V5.
***If the two−speed control on a two−speed outdoor unit is set for LATCH 2 (15 minutes) or LATCH 3 (30 minutes), the compres-
sor will latch into high speed after a Y1 demand has occurred for that period of time.
Page 21
8.Two Stage Integrated Control (A92) Two Stage Operation / Thermostat Selection Jumper
GHR32Q−5 Units The control can be utilized in two modes: SINGLE−STAGE
thermostat or TWO−STAGE thermostat. The thermostat
DANGER selection jumper E20, located just below dip switches 1
through 4 (figure 20), must be positioned for the particular
Shock hazard. application. The jumper is factory set on TWO" for use
Disconnect power before servicing. Control is not with a two−stage thermostat with two stage heat. Re−posi-
field repairable. If control is inoperable, simply tion jumper to SINGLE" for use with a single stage thermo-
replace entire control. stat with two stage heat.
Can cause injury or death. Unsafe operation will While in the single−stage thermostat mode (single jumper
result if repair is attempted.
setting), the burners will always fire on first−stage heat. The
All GHR32Q units are equipped with the Lennox two− combustion air inducer will operate on low speed and in-
stage integrated SureLight control board. The system door blower will operate on low heat speed. After a field se-
consists of a ignition control board (figure 20 with control lectable 10 or 15 minute delay (dip switch 3), the unit will
terminal designations in tables 12, 13 and 14) and ignitor switch to second stage heat. While in the two−stage ther-
(figure 8). The board and ignitor work in combination to en- mostat mode (two jumper setting) the burners will fire on
sure furnace ignition and ignitor durability. The board con- first−stage heat. The combustion air inducer will operate on
trols all major furnace operations. The board features two low speed and indoor blower will operate on low heat
LED lights, DS1 and DS2 for troubleshooting. The board speed. The unit will switch to second−stage heat on call
also has two accessory terminals rated at (1) one amp from the indoor thermostat. If there is a simultaneous call
each. See table 15 for troubleshooting diagnostic codes. for W1 and W2 (first and second stage heat) the unit will fire
on first stage heat and will switch to second stage heat after
30 seconds of operation. See Sequence of Operation flow
Electronic Ignition charts in the back of this manual for more detail.
At the beginning of each heat cycle, SureLight control mon-
itors the first stage and second stage combustion air induc- Dip Switch Settings
er prove switch. The control will not begin the heating cycle
if the first stage prove switch is closed (by−passed). Like- Dip Switches 1 and 2 − Heating Fan off Delay − The fan on
wise the control will not begin the second stage heating time of 45 seconds is not adjustable. Fan off time (time that
cycle if the second stage prove switch is closed and will al- the blower operates after the heat demand has been satis-
low first stage heat only. However if the second stage prove fied) can be adjusted by flipping the dip switches 1 and 2
switch closes during the first stage pre−purge, the control located on the SureLight integrated control. The unit is
will still respond to second stage heat. Once the first stage shipped with a factory fan off setting of 90 seconds. Fan off
prove switch is determined to be open, the combustion air time will affect comfort and is adjustable to satisfy individual
inducer is energized on low (first stage) heat speed. When applications. For customized comfort, monitor the supply
the differential in the prove switch is great enough, the air temperature once the heat demand is satisfied. Note the
prove switch closes and a 15−second pre−purge begins. If supply air temperature at the instant the blower is de−ener-
the switch is not proven within 2−1/2 minutes, the control
gized. Adjust the fan−off delay to achieve a supply air tem-
goes into Watchguard−Pressure Switch mode for a 5−min-
perature between 90° − 110° at the instant the blower is de−
ute re−set period.
energized. (Longer delay times allow for lower air
After the 15−second pre−purge period, the SureLight ignitor
temperature, shorter delay times allow for higher air tem-
warms up for 20 seconds after which the gas valve opens
for a 4−second trial for ignition. The ignitor energizes during perature). See table 10 for dip switch settings.
the trial until flame is sensed. If ignition is not proved during TABLE 10
the 4−second period, the control will try four more times with Heating Fan Off Delay
an inter purge and warm−up time between trials of 35 sec- Delay (Seconds)
onds. After a total of five trials for ignition (including the ini- Switch 1 Switch 2
tial trial), the control goes into Watchguard−Flame Failure 60 Off Off
mode. After a 60−minute reset period, the control will begin 90 Off On
the ignition sequence again. 120 On Off
The SureLight control board has an added feature that pro-
180 On On
longs the life of the ignitor. After a successful ignition, the
SureLight control utilizes less power to energize the ignitor
Switch 3 − Second Stage Delay (Used with Single−Stage
on successive calls for heat. The control continues to ramp
down the voltage to the ignitor until it finds the lowest Thermostat Only) −− This switch is used to determine the
amount of power that will provide a successful ignition. This second stage on delay when a single−stage thermostat is
amount of power is used for 255 cycles. On the 256th call being used. The switch is factory−set in the ON position,
for heat, the control will again ramp down until the lowest which provides a 10−minute delay before second−stage
power is determined and the cycle begins again. heat is initiated. If the switch is toggled to the OFF position,
Page 22
it will provide a 15−minute delay before second−stage heat
is initiated. This switch is only activated when the thermo- TWO−STAGE INTEGRATED CONTROL BOARD
stat selector jumper is positioned for SINGLE−stage ther-
mostat use.
Switch 4 − Cooling Fan off Delay − The fan on delay time
LEDs
of 2 seconds is not adjustable. Fan off time (time that the
blower operates after the cool demand has been satisfied)
DIP
can be adjusted by flipping dip switch 4. The unit is shipped SWITCHES
1−4
with a factory fan off setting of 45 seconds. Fan off time will
affect comfort and is adjustable to satisfy individual ap-
plications. See table 11 for cool fan off time settings.
TABLE 11
Cooling Fan Off Delay
SENSOR
Delay (Seconds) Switch 4
2 Off
45 On
FACTORY−
Diagnostic LED’s (DS1 and DS2) INSTALLED
JUMPER
Two diagnostic LED’S are located on the two−stage inte-
grated control board. See figure 20. These light flashes
correspond with the codes detailed in table 15.
Factory Installed Jumper Y1 to Y2
A factory−installed jumper from Y1 to Y2 terminals on the
integrated control board terminal strip must be removed for THERMOSTAT CONNECTIONS (TB1)
two−stage cooling.
TABLE 12
Integrated Control Board Terminals
120VAC Neutral
LINE Line
XFMR Transformer
EAC Electronic Air Cleaner
CIRC Indoor Blower
HUM Humidifier
120VAC Line
HUM Humidifier
XMFR Transformer
DIP SWITCH(ES) FUNCTION
LINE Line 1 and 2 Blower Off Delay (Heating Mode)
3 Second Stage ON Delay (Single−stage t’stat)
PARK For Unused Leads
4 Blower Off Delay (Cooling Mode)
COOL Cooling Speed
EAC Electronic Air Cleaner
HI HEAT High Heat Speed
LO HEAT Low Heat, Low Cool and Continuous Fan
Speed FIGURE 20
Page 23
TABLE 13 TABLE 14
Integrated Control Board 5 Pin Terminal Integrated Control Board 12Pin Terminal
PIN # Function PIN # Function
1 Ignitor 1 Gas Valve 2nd Stage (High Fire)
2 Combustion Air Inducer High Speed
2 Second Stage Prove Switch
3 Combustion Air Inducer Low Speed
3 Not Used
4 Combustion Air Inducer Neutral
4 Ground
5 Ignitor Neutral
5 24V Hot
6 Primary Limit In
7 Gas Valve 1st stage (Low Fire)
8 Gas Valve Common
9 24V Neutral
10 Ground
11 Primary Limit Out
12 1st Stage Prove Switch
TABLE 15
DIAGNOSTIC CODES
Diagnostic LEDs are labeled DS1 and DS2. See figure 20 for location of diagnostic LEDs.
DS1 DS2 DESCRIPTION
SIMULTANEOUS SIMULTANEOUS Power on − Normal operation.
SIMULTANEOUS SIMULTANEOUS Normal operation − signaled when heating demand initiated at thermostat.
FAST FLASH FAST FLASH
SLOW FLASH ON Primary, secondary or rollout limit switch open. Limits must close within 3 minutes
or unit goes into 1 hour Watchguard.
Pressure switch open;
OFF SLOW FLASH OR: Blocked inlet/exhaust vent;
OR: Pressure switch closed prior to activation of combustion air inducer.
OFF FAST FLASH OR: Blocked inlet/exhaust vent;
Watchguard −− burners failed to ignite; OR limit open more than 3 minutes;
ALTERNATING ALTERNATING
OR lost flame sense 5 times in one heating cycle;
SLOW FLASH SLOW FLASH
OR pressure switch opened 5 times in one heating cycle.
ON ON
ON OFF Circuit board failure or control wired incorrectly. Check 24 and 115 volts to board.
OFF ON
SLOW FLASH FAST FLASH Low flame signal. Measures below 0.23 microAmps. Replace flame sense rod.
The following conditions are sensed during the ignitor warm−up period only:
1) Improper main ground;
ALTERNATING ALTERNATING 2) Broken ignitor; OR: Open ignitor circuit;
FAST FLASH FAST FLASH 3) Line voltage below 75 volts.
(If voltage lower than 75 volts prior to ignitor warm-up, control will signal waiting on
call from thermostat, and will not respond.
NOTE − Slow flash rate equals 1 Hz (one flash per second). Fast flash rate equals 3 Hz (three flashes per second).
Minimum flame sense current = 0.17−0.22 microAmps.
Page 24
9.Two Stage Variable Speed Integrated Two Stage Operation / Thermostat Selection Jumper
Control (A92) GHR32V−5 Units The control can be utilized in two modes: SINGLE−STAGE
All GHR32V−5 units are equipped with the Lennox two− thermostat or TWO−STAGE thermostat. The thermostat
stage, variable speed integrated SureLight control board. selection jumper E20, located just below dip switches 1
The system consists of a ignition / blower control board through 3 (figure 21), must be positioned for the particular
(figure 21 with control terminal designations in tables 16 application. The jumper is factory set on TWO" for use
with a two−stage thermostat with two stage heat. Re−posi-
through 19) and ignitor (figure 8). The board and ignitor
tion jumper to SINGLE" for use with a single stage thermo-
work in combination to ensure furnace ignition and ignitor
stat with two stage heat.
durability. The SureLight integrated board controls all ma- While in the single−stage thermostat mode (single jumper
jor furnace operations. The board features two LED lights, setting), the burners will always fire on first−stage heat. The
DS1 and DS2 for troubleshooting and four LED lights combustion air inducer will operate on low speed and in-
(DS3, DS6, DS7 and DS8) to show furnace status. The door blower will operate on low heat speed. After a field se-
board also has two accessory terminals rated at (1) one lectable 10 or 15 minute delay (dip switch 3), the unit will
amp each. See table 20 for status code and table 21 for switch to second stage heat. While in the two−stage ther-
mostat mode (two jumper setting) the burners will fire on
troubleshooting diagnostic codes.
first−stage heat. The combustion air inducer will operate on
Electronic Ignition low speed and indoor blower will operate on low heat
At the beginning of each heating cycle, the SureLight con- speed. The unit will switch to second−stage heat on call
trol monitors the first stage and second stage combustion from the indoor thermostat. If there is a simultaneous call
air inducer prove switch. The control will not begin the heat- for W1 and W2 (first and second stage heat) the unit will fire
ing cycle if the first stage prove switch is closed (by− on first stage heat and switch to second stage heat after 30
passed). Likewise the control will not begin the second seconds of operation. See Sequence of Operation flow
stage heating cycle if the second stage prove switch is charts in the back of this manual for more detail.
closed, and will allow first stage heat only. However if the TABLE 16
second stage prove switch closes during the first stage pre−
Two Stage Ignition / Blower Control Terminals
purge, the control WILL respond to second stage heat call.
Once the first stage prove switch is determined to be open, 120VAC Neutral
the combustion air inducer is energized on low (first stage) LINE Line 120VAC Neutral
heat speed. When the differential in the prove switch is XFMR Transformer 120VAC Neutral
great enough, the prove switch closes and a 15−second
EAC Electronic Air Cleaner 120VAC Neutral
pre−purge begins. If the switch is not proven within 2−1/2
CIRC Indoor Blower 120VAC Neutral
minutes, the control goes into Watchguard−Pressure
Switch mode for a 5−minute re−set period. HUM Humidifier 120VAC Neutral
After the 15−second pre−purge period, the SureLight ignitor 120VAC Line
warms up for 20 seconds after which the gas valve opens
HUM Humidifier 120VAC Hot
for a 4−second trial for ignition. The ignitor energizes during
XMFR Transformer 120VAC Hot
the trial until flame is sensed. If ignition is not proved during
the 4−second period, the control will try four more times with LINE Line 120VAC Hot
an inter purge and warm−up time between trials of 35 sec- CIRC Indoor Blower 120VAC Hot
onds. After a total of five trials for ignition (including the ini- EAC Electronic Air Cleaner 120VAC Hot
tial trial), the control goes into Watchguard−Flame Failure
mode. After a 60−minute reset period, the control will begin TABLE 17
the ignition sequence again. SureLight Board 5 Pin Terminal Designation
The SureLight control board has an added feature that pro- PIN # Function
longs the life of the ignitor. After a successful ignition, the 1 Ignitor
SureLight control utilizes less power to energize the ignitor 2 Combustion Air Inducer High Speed
on successive calls for heat. The control continues to ramp
3 Combustion Air Inducer Low Speed
down the voltage to the ignitor until it finds the lowest
4 Combustion Air Inducer Neutral
amount of power that will provide a successful ignition. This
5 Ignitor Neutral
amount of power is used for 255 cycles. On the 256th call
for heat, the control will again ramp down until the lowest
power is determined and the cycle begins again.
Page 25
TABLE 18
TW0−STAGE, VARIABLE SPEED INTEGRATED
SureLight Board 12Pin Terminal Designation
CONTROL BOARD
PIN # Function
1 Gas Valve 2nd. Stage (High Fire)
DIP
DIAGNOSTIC SWITCHES 2 Second Stage Pressure Switch
LEDs 1−3 3 Not Used
4 Ground
E20
JUMPER 5 24V Hot
6 Primary Limit In
7 Gas Valve 1st. Stage (Low Fire)
8 Gas Valve Common
9 24V Neutral
10 Ground
DIP
LEDs 11 Primary Limit Out
SWITCHES
5 − 12 12 1st Stage Pressure Switch
DS8
FACTORY−
INSTALLED TABLE 19
DS3 JUMPER
DS7 LED
DS6 SureLight Board 16 Pin Blower Control Terminals
PIN # Function
1 Ground
2 Low Heat Speed
ON−BOARD ON−BOARD 3 Ground
JUMPER W914 16 PIN BLOWER JUMPER W951
(cut when CCB1 or CONTROL TERMINALS (cut when heat pump 4 DELAY" Dip Switch Selection
Harmony II are used) is used with FM21)
5 COOL" Dip Switch Selection
THERMOSTAT CONNECTIONS (TB1)
6 Y1" Signal
7 ADJUST" Dip Switch Selection
8 Ground
9 O" From Thermostat
10 DS" Output Signal
11 HEAT" Dip Switch Selection
12 24 VAC
DIP SWITCH FUNCTIONS 13 HIGH HEAT Speed
DIP SWITCH(ES) FUNCTION 14 Y2" Signal
1 and 2 Blower Off Delay
15 G"
3 Second Stage ON Delay (Single−stage t’stat)
4 Not used 16 CFM LED
5 and 6 Cooling Mode Blower Speed
7 and 8 Blower Speed Adjustment
9 and 10 Cooling Mode Blower Ramping Profile
11 and 12 Heating Mode Blower Speed
FIGURE 21
Page 26
TABLE 20
STATUS CODES
STATUS LED COLOR FUNCTION
DS3 DS3−ON indicates that the motor has a demand to operate. (This LED must be on in all
GREEN
ON / OFF ’ modes).
DS6 DS6−blinking indicates the airflow (CFM) demand in the motor. The air flow is determined by
GREEN
CFM" counting blinks between two (2) second pauses. One blink equals roughly 100 CFM.
DS7−ON indicaties the DS to R" jumper has not been cut. When the jumper is cut the system
will be operating with LENNOX HARMONY IIt (See Harmony Installation Instructions) or
DS7
YELLOW with the CCB1 Efficiency Plus control.
HI / LO"
CCB1: When ON, a 24 VAC is being applied and when OFF, it has been removed. This on/off
operation varies the indoor blower’s performance so dehumidification can be enhanced.
DS8
YELLOW DS8−ON indicates the sytem is in HEAT mode.
HEAT"
TABLE 21
DIAGNOSTIC CODES
Diagnostic LEDs are labeled DS1 and DS2. See figure 21 for location of diagnostic LEDs.
DS1 DS2 DESCRIPTION

SIMULTANEOUS SIMULTANEOUS Power on − Normal operation.
SIMULTANEOUS SIMULTANEOUS Normal operation − signaled when heating demand initiated at thermostat.
FAST FLASH FAST FLASH
SLOW FLASH ON Primary, secondary or rollout limit switch open. Limits must close within 3 minutes
or unit goes into 1 hour Watchguard.
OFF SLOW FLASH OR: Blocked inlet/exhaust vent;
OFF FAST FLASH OR: Blocked inlet/exhaust vent;
Watchguard −− burners failed to ignite; OR limit open more than 3 minutes;
ALTERNATING ALTERNATING
OR lost flame sense 5 times in one heating cycle;
SLOW FLASH SLOW FLASH
OR pressure switch opened 5 times in one heating cycle.
ON ON
ON OFF Circuit board failure or control wired incorrectly. Check 24 and 115 volts to board.
OFF ON
SLOW FLASH FAST FLASH Low flame signal. Measures below 0.23 microAmps. Replace flame sense rod.
The following conditions are sensed during the ignitor warm−up period only:
1) Improper main ground;
ALTERNATING ALTERNATING 2) Broken ignitor; OR: Open ignitor circuit;
FAST FLASH FAST FLASH 3) Line voltage below 75 volts.
(If voltage lower than 75 volts prior to ignitor warm-up, control will signal waiting on
call from thermostat, and will not respond.
NOTE − Slow flash rate equals 1 Hz (one flash per second). Fast flash rate equals 3 Hz (three flashes per second).
Minimum flame sense current = 0.17−0.22 microAmps.
Page 27
Dip Switch Settings TABLE 23
Switches 1 and 2 − Blower Off Delay The blower−on delay Cooling Mode Blower Speeds
of 45 seconds is not adjustable. The blower−off delay (time Speed Switch 5 Switch 6
that the blower operates after the heating demand has 1 − Low On On
been satisfied) can be adjusted by moving switches 1 and 2 2 − Medium Low Off On
on the integrated control board. The unit is shipped from 3 − Medium High On Off
the factory with a blower−off delay of 90 seconds. The 4 − High (Factory) Off Off
blower off delay affects comfort and is adjustable to satisfy
individual applications. Adjust the blower off delay to Switches 7 and 8 − Blower Speed Adjustment Switches
achieve a supply air temperature between 90° and 110°F at 7 and 8 are used to select blower speed adjustment set-
the exact moment that the blower is de−energized. Longer tings. The unit is shipped from the factory with the dip
off delay settings provide lower supply air temperatures; switches positioned for NORMAL (no) adjustment. The dip
shorter settings provide higher supply air temperatu- switches may be positioned to adjust the blower speed by
res.The table below provides the blower off timings that will +10% or −10% to better suit the application. The table be-
result from different switch settings. low provides blower speed adjustments that will result from
TABLE 22 different switch settings. Refer to blower data tables at the
Blower Off Delay Switch Settings front of this manual for corresponding cfm values.
Blower Off Delay TABLE 24
Switch 1 Switch 2 Blower Speed Adjustment
(Seconds)
60 Off Off Adjustment Switch 7 Switch 8
90 Off On +10% (approx.) On Off
120 On Off NORMAL (Factory) Off Off
180 On On −10% (approx.) Off On
Switch 3 − Second Stage Delay (Used with Single−Stage
Switches 9 and 10 − Cooling Mode Blower Speed
Thermostat Only) This switch is used to determine the
Ramping −− Switches 9 and 10 are used to select cooling
second stage on delay when a single−stage thermostat is
mode blower speed ramping options. Blower speed ramp-
being used. The switch is factory−set in the ON position,
ing may be used to enhance dehumidification perfor-
which provides a 10−minute delay before second−stage
mance. The switches are factory set at option A which has
heat is initiated. If the switch is toggled to the OFF position,
the greatest effect on blower motor performance. The table
it will provide a 15−minute delay before second−stage heat
below provides the cooling mode blower speed ramping
is initiated. This switch is only activated when the thermo-
options that will result from different switch settings. The
stat selector jumper is positioned for SINGLE−stage ther-
cooling mode blower speed ramping options are detailed
mostat use.
on the next page. See unit nameplate for manufacturing
Switch 4 − Not used date.
Switches 5 and 6 − Cooling Mode Blower Speed TABLE 25
Switches 5 and 6 are used to select cooling blower motor Cooling Mode Blower Speed Ramping
speed. The unit is shipped from the factory with the dip Ramping Option Switch 9 Switch 10
switches positioned for high speed (4) indoor blower motor A (Factory) Off Off
operation during the cooling mode. The table below pro- B On Off
vides the cooling mode blower speeds that will result from C Off On
different switch settings. Refer to blower data tables at the D* On On
front of this manual for corresponding cfm values. *Only option for CCB1
Page 28
GHR32V units manufactured before April 2003 GHR32V units manufactured April 2003 and later
Ramping Option A (Factory Selection) Ramping Option A (Factory Selection)
D Motor runs at 50% for 1/2 minute. S Motor runs at 50% for 30 seconds.
D Motor then runs at 82% for approximately 7−1/2 min- S Motor then runs at 82% for approximately 7−1/2 min-
utes. utes. If demand has not been satisfied after 7−1/2 min-
D If demand has not been satisfied after 7−1/2 minutes,
utes.
S Motor runs at 100% until demand is satisfied.
D Once demand is met, motor runs at 50% for 1/2 min-
ute. S Once demand is met, motor runs at 50% for 30 sec-
D Motor ramps down to off. onds then −
S ramps down to stop.
7−1/2 MIN 100% 7 1/2 MIN 100%

OFF 82% CFM CFM OFF OFF 82% CFM CFM OFF
1/2 MIN 1/2 MIN 1/2 MIN 1/2 MIN
50% CFM 50% CFM 50% CFM 50% CFM
COOLING DEMAND COOLING DEMAND
Ramping Option B Ramping Option B

D Motor runs at 50% for 1/2 minute. S Motor runs at 82% for approximately 7−1/2 minutes. If
D Motor then runs at 82% for approximately 7−1/2 min- demand has not been satisfied after 7−1/2 minutes −
utes. S motor runs at 100% until demand is satisfied.
D If demand has not been satisfied after 7−1/2 minutes, S Once demand is met, motor ramps down to stop.
D Once demand is met, motor ramps down to off.
7 1/2 MIN 100% CFM
OFF 82%CFM OFF
7−1/2 MIN COOLING DEMAND
OFF 82% CFM
100% CFM OFF
1/2 MIN
50% CFM
COOLING DEMAND
Ramping Option C
Ramping Option C S Motor runs at 100% until demand is satisfied.
D Motor runs at 82% for approximately 7−1/2 minutes. S Once demand is met, motor runs at 100% for 60 sec-
D If demand has not been satisfied after 7−1/2 minutes, onds. Then,
the motor runs at 100% until demand is satisfied. S ramps down to stop.
100% CFM 100% CFM
OFF OFF
7−1/2 MIN COOLING DEMAND
82%CFM 100% CFM OFF
OFF
COOLING DEMAND
Ramping Option D
Ramping Option D S− Motor runs at 100% until demand is satisfied.
D Motor runs at 100% until demand is satisfied. S− Once demand is met, motor ramps down to stop.
100% CFM 100% CFM

OFF OFF OFF OFF
COOLING COOLING
DEMAND DEMAND
Page 29
Switches 11 and 12 − Heating Mode Blower Speed On−Board Jumper W951
Switches 11 and 12 are used to select heating mode blower On−board jumper W951, which connects terminals R and O
motor speed. The unit is shipped from the factory with the on the integrated control board, must be cut when the fur-
dip switches positioned for medium low (2) speed indoor nace is installed in applications which include a heat pump
blower motor operation during the heating mode. The table unit and the FM21 FuelMaster control board.
below provides the heating mode blower speeds that will Factory−Installed Jumper Y1 to Y2
result from different switch settings. Refer to blower data
A factory−installed jumper from Y1 to Y2 terminals on the
tables at the front of this manual for corresponding cfm val- integrated control board terminal strip must be removed if
ues. two−stage cooling will be used.
TABLE 26
Heating Mode Blower Speeds Diagnostic LEDs (DS1 and DS2)
Speed Switch 11 Switch 12 Two diagnostic LEDs are located on the two−stage, vari-
1 − Low On On able speed integrated control just to the left of the first bank
2 − Medium Low of dip switches. These lights’ flashes correspond with diag-
Off On nostic codes detailed on in table 15.
(Factory)
3 − Medium High On Off Status LEDs (HEAT, HI/LO, ON/OFF and CFM)
4 − High Off Off The integrated control includes four LEDs which indicate
On−Board Jumper W914 operating status. The green ON/OFF LED is lit any time the
On−board jumper W914, which connects terminals DS and blower is operating. The green CFM LED indicates the
R on the integrated control board, must be cut when the fur- blower motor speed. Count the number of blinks between
nace is installed with either the Harmony II zone control the two−second pauses to determine the CFM. Each blink
board or the CCB1 EfficiencyPlus humidity control. Refer to represents approximately 100 CFM. The yellow HI/LO LED
table 27 for operation sequence in applications including a is lit when the W914 (DS to R) jumper has not been clipped
GHR32V, CCB1 and single−speed outdoor unit. Table 28 for CCB1 or Harmony operation. The yellow HEAT LED is
gives the operation sequence in applications with a two− lit when the indoor blower is operating at the HEATING
speed outdoor unit. speed.
Table 27
Operating Sequence
GHR32V−5, CCB1 and Single−Speed Outdoor Unit
OPERATING MODE SYSTEM DEMAND SYSTEM RESPONSE
Thermostat *Relative Humidity Blower
System Condition CFM Comments
Demand (EfficiencyPlus Lights)
(COOL)
Normal operation Y1 No demand. Humidity COOL Compressor demand and indoor blower
level is acceptable speed controlled by thermostat demand.
*Call for humidity Humidity level rises 77%/74% Call for dehumidification initiated by CCB1
removal during Y1 above setpoint. Demand control. Indoor blower speed reduced by
of COOL
cooling demand initiated. CCB1 control.
Dehumidification Humidity level falls below When humidity demand is satisfied, blow-
demand satisfied Y1 COOL er speed immediately increases to the
setpoint. No demand
during cooling demand. COOL CFM to hasten the end of the cycle.
Humidity level above set-
Call for cooling after None Off
point. Demand initiated. Dehumidification mode begins when rela-rela
call for humidity
Humidity level above set- 77%/74% tive humidity is greater than setpoint.
removal. Y1
point. Demand initiated. of COOL
Humidity demand None Over setpoint (1 or more) Off While unit is not operating (no thermostat
satisfied between
demand) slide switch is moved down and
demand),
thermostat demands Y1 Change to acceptable COOL back up. Blower operates at COOL CFM.
(unit off cycle).
NOTE − When changing unit mode of operation from cooling to heating, indicating lights that are on will stay on until the first ther-
mostat heating demand.
* Reduced blower speed is 77% of COOL for V3 units and 74% of COOL for the V5 units.
Page 30
Table 28
Operating Sequence
GHR32V−5, CCB1 and Two−Speed Outdoor Unit
OPERATING MODE SYSTEM DEMAND SYSTEM RESPONSE
System Thermostat *Relative Humidity ****Compressor Blower CFM
Comments
Condition Demand (EfficiencyPlus Lights) Speed (COOL)
55% of
Y1 No demand. Acceptable Low HIGH COOL Compressor demand and indoor
Normal operation blower speed controlled by
Y2 No demand. Acceptable High HIGH COOL thermostat demand
55% of
Y1 No demand. Acceptable Low HIGH COOL
Humidity level rises slightly 55% of
Call for humidity Y1 (1) above setpoint. Demand Low HIGH COOL Dehumidification mode does not begin
removal during initiated. until after initial thermostat demand is
1st−stage cooling Demand Humidity level remains satisfied and new cooling demand is
demand slightly (1) above setpoint. Off Off initiated.
satisfied
Demand continues.
Humidity level remains **77%/74% of
Y1 slightly (1) above setpoint. High
HIGH COOL
Demand continues.
No demand. Acceptable 55% of If humidity rises significantly above set-
Significant increase in Y1 Low
HIGH COOL signifi
point, or if slide switch is moved signifi-
humidity during
Humidity level rises significantly,
l unit i will
ill iimmediately
di l go iinto d
de-
thermostat cooling **77%/74% of
Y1 cantly (2 or more) above High humidification mode (in presence of
demand. HIGH COOL
setpoint. Demand initiated. thermostat demand).
Humidity level **77%/74% of
Y1 High
above setpoint. HIGH COOL When humidity demand is satisfied,
Humidity level falls below blower immediately shifts to the COOL
Humidity demand Y1 High HIGH COOL
setpoint. No demand. CFM in order to hasten the end of the
satisfied during
cycle Unit can only shift out of high
cycle.
thermostat demand. None No demand. Acceptable Off Off speed compressor operation at begin
begin-
55% of ning of next cycle.
Y1 No demand. Acceptable Low
HIGH COOL
Y2 No demand. Acceptable High HIGH COOL
Call for humidity
removal during 2nd Humidity level rises slightly **77%/74% of Blower immediately changes speed in
stage thermostat Y2 (1) above setpoint. Demand High response to thermostat demand.
HIGH COOL
demand initiated.
Y2 No demand. Acceptable High HIGH COOL
Humidity level is slightly (1) Off Dehumidification mode (high speed
*Call for 1st stage None Off
above setpoint. compressor) begins with next thermo
thermo-
cooling after call for
Humidity level is slightly (1) 55% of stat demand after initial demand is sat-
humidity removal. Y1 Low
above setpoint. HIGH COOL isfied.
Humidity level is slightly (1) Off
Call for 2nd stage None Off Reduced blower speed (dehumidifica-
above setpoint.
cooling after call for tion speed) begins immediately with
humidity removal Humidity level is slightly (1) **77%/74% of thermostat demand
Y2 High
above setpoint. HIGH COOL
Humidity level is significantly If humidity increases significantly over
None Off Off
Call for cooling after above setpoint (2 or more). setpoint, or if slide switch is moved,
significant increase in unit immediately goes into dehumidifi-
dehumidifi
humidity Humidity level is significantly **77%/74% of cation mode (in presence of thermostat
Y1 or Y2 High
above setpoint (2 or more). HIGH COOL demand).
Humidity demand Humidity level is slightly (1) While unit is not operating (no thermo-
None Off Off
satisfied between above setpoint. stat demand), slide switch is moved
thermostat demands down and back up. up Blower and com
com-
Humidity level falls below HIGH COOL pressor operate at high speed until
(unit off cycle). Y1 or Y2 High
setpoint. No demand. next thermostat demand.
Note − During mode of operation change from cooling to heating, indicating lights will not change until the first thermostat heating
demand.
*IMPORTANT - If power to unit is turned on with CCB1 calling for humidity removal, outdoor unit may be locked into high speed
indefinitely. To reset, move the humidity slide switch all the way down then back up to desired setpoint while the unit is running.
** Reduced blower speed is 77% of COOL for the V3 units; 74% of COOL for V5.
***If the two−speed control on a two−speed outdoor unit is set for LATCH 2 (15 minutes) or LATCH 3 (30 minutes), the compres-
sor will latch into high speed after a Y1 demand has occurred for that period of time.
Page 31
GHR32 HEAT EXCHANGER
HEAT EXCHANGER
SUPPORT
CONDENSER COIL
COMBUSTION
AIR BLOWER
COMBUSTION AIR
BLOWER MOTOR
COLD HEADER
(COLLECTOR)
BOX
HOT END HEADER

(COLLECTOR) BOX
PRIMARY LIMIT
CONTROL (S10) GAS VALVE
MANIFOLD
LENNOX DURALOKPlust
HEAT EXCHANGER
(Assembly)
CLAMSHELL
(Each Segment)
CORBEL
ORIFICE
CUPS
BURNER
BOX
FLAME SENSOR
ASSEMBLY
BURNERS FLAME SIGHT

(VIEWING) GLASS
SURELIGHT
BURNER
IGNITOR
ORIFICE
FIGURE 22
Page 32
C−Heating Components (Figure 22)
DETAIL VIEW OF BURNER CLUSTER MOUNTING
Combustion air blower (B6), primary limit control (S10), Sur-
eLight ignitor, flame sensor, burners, flame rollout switch
Burner Box
(S47), gas valve (GV1), combustion air blower switch (S18),
and clamshell heat exchangers are located in the heating
compartment. The heating compartment can be accessed
by removing the burner access panel. Raised
Toggle Locks
1.Combustion Air Inducer Blower (B6)
All GHR32 units use a two−stage combustion air inducer blow-
er to move air through the burners and heat exchanger during
heating operation. The blower uses a 120VAC motor. The mo-
tor operates during all heating operation and is controlled by
the SureLight integrated board (A92) and two−stage control Burner Cluster
board (A86). The combustion air inducer blower operates on
Screw
low speed during first stage heat (low fire), then switches to Flange
high speed for second stage heat (high fie). FIGURE 24
2.Combustion Air Blower Capacitor (C3)
PSC Motors only 4.Burners
GHR32 units with a PSC combustion air blower motor, Figure 22 shows the arrangement of the burner box. Table 30
shows how many burners are used per unit. See figure 24 for
will have a thermally protected 3 MFD 300VAC capacitor.
a more detailed view. Notice the position of the raised toggle
The capacitor is mounted on the combustion air blower
lockets.
housing.
TABLE 30
3.Primary Limit Control (S10) NUMBER OF HEAT
Figure 23 shows the primary limit (S10) used on GHR32 units. GHR32 UNIT SIZE EXCHANGER CLAMSHELLS /
S10 is located in the middle of the heating vestibule panel. BURNERS
When excess heat is sensed in the heat exchanger, the limit GHR32-50 2
will open. If the limit is tripped, the furnace control ener- GHR32-75 3
GHR32Q3/4-100 4
gizes the supply air blower and closes the gas valve. The
GHR32-120 5
limit automatically resets when unit temperature returns to
normal. The switch is factory set and cannot be adjusted. All units use inshot burners Burners are factory set and do not
See table 29 for limit set points. require adjustment. A sight glass is furnished in the burner
box assembly for flame viewing. Always operate the unit
LIMIT CONTROL (S10) with the burner box cover in place. Burners can be removed
SPADE CONNECTORS
as an assembly for service. Burner maintenance and service

is detailed in the SERVICE CHECKS sections of this manu-
LIMIT
al. Each burner uses an orifice which is precisely matched to

the burner input. The orifice is threaded into the burner man-
ifold. The burner is supported by the orifice and will easily
INSULATING COVER (s)
slide off for service. Each orifice and burner are sized specif-
ically to the unit. Refer to Lennox Repair Parts Listing for cor-
FIGURE 23
rect sizing information. A flame retention ring in the end of
each burner maintains correct flame length and shape and
TABLE 29 keeps the flame from lifting off the burner head. In addition, the
GHR32 UNIT SIZE LIMiT SET POINT burner entrance to each clamshell (Figure 22) is fitted with a
GHR32-50 300° corbel cup (orifice) used to direct the flow of combustion prod-
GHR32-75 300° ucts.
GHR32Q3/4-100 220° NOTE−Do not use thread-sealing compound on the ori-
GHR32-120 175° fices. Thread-sealing compound may plug the orifices.
Page 33
5.Clamshell Heat Exchanger 7.Gas Valve
GHR32 units use an aluminized steel primary and stain- The GHR32 uses a gas valve manufactured by White
less steel secondary heat exchanger assembly. Table 30 Rodgers or Honeywell. The valve is two-stage internally
shows how many heat exchanger clamshells are used redundant to assure safety shut−off. If the gas valve must
per unit. Heat is transferred to the air stream from all sur- be replaced, the same type valve must be used. The
faces of the heat exchanger. The shape of the heat ex- Honeywell valve can be field converted to LP and is adjust-
changer ensures maximum efficiency. able on both low and high fire. WhiteRodgers supplies two
seperate valves for natural and LP and is adjustable for
The combustion air blower pulls fresh air through the air in- high fire ONLY.
take box. This air is mixed with gas in the burner venturi 24VAC terminals and gas control knob are located on top of
and at the corbel orifices. The gas / air mixture is then the valve. Terminals on the gas valve are connected to wires
burned at the entrance of each clamshell. Combustion from the SureLight integrated control and the two−stage con-
gases are then pulled through the primary and secondary heat trol. 24V applied to the terminals energizes the valve.
exchangers and exhausted out the exhaust vent pipe.
Inlet and outlet pressure taps are located on the valve. A regu-
lator adjustment screw is located on the side of the valve. Re-
6.Flame Rollout Switch (S47) fer to figures 26, 27 , and 28 for location of valve features.
Flame rollout switch S47 is a SPST N.C. high temperature limit NOTE−WhiteRodgers valve is not adjustable on low fire.
located behind the burner air intake fitting on the burner box Do not attempt to regulate low fire manifold pressure.
assembly (see figure 25). S47 is wired to the burner ignition
control A3. When S47 senses flame rollout (indicating a WHITE RODGERS 36E SERIES GAS VALVE
blockage in the combustion air passages), the flame rol- NATURAL GAS
lout switch trips, and the ignition control immediately (LOW HEAT MANIFOLD PRESSURE FACTORY SET.
DO NOT ADJUST.)
closes the gas valve. HIGH HEAT
MANIFOLD
Switch S47 in all GHR32 units is factory preset to open at PRESSURE
320_F + 12_F (160_C + 6.7_C) on a temperature rise. All ADJUSTMENT
ON SIDE
flame rollout switches are manually reset. (under cap)
FLAME ROLLOUT SWITCH (S47)

MANIFOLD
PRESSURE
FLAME ROLLOUT
OUTLET ON
SWITCH (S47) SIDE
FIGURE 27
WHITE RODGERS 36E SERIES GAS VALVE
PROPANE GAS
(LOW HEAT MANIFOLD PRESSURE FACTORY SET.
DO NOT ADJUST.)
HIGH HEAT
MANIFOLD
PRESSURE
FIGURE 25 HI
P M ADJUSTMENT
ON SIDE
C (under cap)
HONEYWELL VR8205 Series Gas Valve

HIGH FIRE ADJUSTMENT MANIFOLD
SCREW (UNDER CAP) MANIFOLD PRESSURE
PRESSURE OUTLET ON
TAP SIDE
FIGURE 28
100% Sealed Combustion
The burner box is completely sealed and operates under
a negative pressure. A pressure hose is connected from the
LOW FIRE burner box to the gas valve regulator. The gas valve senses
ADJUSTMENT the pressure in the burner box and changes gas valve outlet
SCREW (manifold) pressure based on changes in burner box pres-
(UNDER CAP)
INLET PRESSURE TAP VALVE SHOWN IN OFF POSITION sure. The intent is to compensate for different vent con-
figurations which can greatly affect the firing rate of the
FIGURE 26
unit.
Page 34
NORMAL OPERATION (Natural Gas Units) Figures 29 and 30 show how gas valve manifold pressure
3.5 changes as burner box pressure changes. The GHR32 is a
3.4 self adjusting unit to maintain a constant output.
MANIFOLD PRESSURE (positive inches water gauge) 8.Combustion Air Prove Switch
3.3
(S18) GHR32−1/−4 Units &
3.2 (S102) GHR32−5 Units
GHR32 series units are equipped with a differential
GAS VALVE OUTPUT
3.1 pressure switch S18 or S102 located on either side of

3.0 the heating compartment cabinet (factory installed on
left side).The switch monitors the differential pressure be-
2.9 tween the downstream and upstream flue gas pressures.
When the unit is installed for horizontal right-hand dis-
2.8
charge, the air proving pressure switch must be moved to
2.7 the opposite side of the unit. Any one of four different switches
may be on the unit. One is manufactured by MPL. The other
OPERATION AT THIS EXTREME
2.6 MAY INDICATE A BLOCKED three switches are manufactured by TRIDELTA / HONEY-
INLET OR OTHER PROBLEM" WELL. Each switch operates the same and can be replaced
2.5
0 −0.2 −0.4 −0.6 −0.8 −1.0 with one another. See figure 31 for combustion air prove
BURNER BOX PRESSURE switch replacment. Hoses must be connected to correct
(Negative inches water gauge
measured on left side of burner box) taps for switch to operate safely and properly. GHR32
Gray area indicates normal operating range + 10% of manifold pressure
The purpose of this chart is to explain unit operation . Each unit may vary depending
model units have color coded tubing to designate positive and
on installation, altitude, intake/exhaust configuration and other factors. negative sides of the pressure switch. Red/Square tubing
FIGURE 29 should always be connected to the positive side of the pres-
sure switch. Gray or Black /Round tubing should always be
NORMAL OPERATION (L.P. Gas Units)
connected to the negative side of the pressure switch. See fig-
10.0
ure 31.
9.9 The switch is a SPST N.O. pressure switch electrically con-
MANIFOLD PRESSURE (positive inches water gauge)
9.8 nected to the integrated control. The purpose of the switch is

to prevent burner operation if the combustion air blower is not
9.7 moving enough air for proper combustion.
On start-up, the switch senses that the combustion air blower
GAS VALVE OUTPUT
9.6 is operating. It closes a circuit to the ignition control when

9.5 the difference in pressure across the pressure switch ex-
ceeds 0.90" W.C. (223.78Pa). If the switch does not suc-
9.4 cessfully sense the required differential, the switch can-
not close and the furnace cannot operate. The switch is
9.3
factory set and is not adjustable. If the flue or air inlet be-
9.2 come obstructed during operation, the switch senses a
OPERATION AT THIS EXTREME
loss of pressure differential and opens the circuit to the igni-
9.1 MAY INDICATE A BLOCKED tion control. If the condensate line is blocked, water will back
INLET OR OTHER PROBLEM"
up into the header box and reduce the pressure differential
9.0
0 −0.2 −0.4 −0.6 −0.8 −1.0 across the switch. The pressure switch will open if the differ-
BURNER BOX PRESSURE ential drops below 0.75" W.C. + 05" W.C. (186.48 Pa +
(Negative inches water gauge
measured on left side of burner box) 12.4 Pa).
Gray area indicates normal operating range + 10% of manifold pressure
The purpose of this chart is to explain unit operation . Each unit may vary depending
on installation, altitude, intake/exhaust configuration and other factors.
FIGURE 30
Page 35
MPL
TRIDELTA / HONEYWELL
NEGATIVE (Metal/Plastic Construction)
PRESSURE
(Marked With "V") POSITIVE
PRESSURE
(Marked With "P") NEGATIVE PRESSURE
(Marked With "−")
POSITIVE
PRESSURE
(Marked With "+")
TRIDELTA / HONEYWELL
(All Metal Construction)
TRIDELTA / HONEYWELL IS2
NEGATIVE POSITIVE PRESSURE (NO
Markings Electrical Terminal NEGATIVE PRESSURE
PRESSURE (gray side marked −")
(NO Markings) and Hose Connection Side)
Hose Connec-
tion Side Only)
POSITIVE PRESSURE
1.000
SCALE
(black side marked +")
HORIZONTAL LEFT HAND AIR DISCHARGE DOWN FLOW AIR DISCHARGE

Connect hose (red square) to POSITIVE side on pres- Connect hose (gray or black round) To NEGATIVE side
sure switch and open tap on FRONT of collector box. on pressure switch and open tap on FRONT of collector
box.
Pressure AIR FLOW
Switch
Collector Box
Pressure
Switch
AIR FLOW Connect hose

(red square) to
POSITIVE side
on pressure
switch and open
tap on FRONT
of collector box.
Connect hose (gray or black

round) To "NEGATIVE"side on
pressure switch and open tap on
SIDE of collector box.
HORIZONTAL RIGHT HAND DISCHARGE
Connect the red square hose to the POSITIVE side on pressure
switch and the open tap on the FRONT of the collector box.
Pressure Collector Box

Switch
NEGATIVE PRESSURE CONNECTIONS
must be
(Gray or Black round tubing beginning with −3 models) on top side
of unit.
BLANK STEMS EARLY MODEL

UNITS ONLY
AIR FLOW
POSITIVE PRESSURE CONNECTIONS Connect the gray or black round hose to the NEGATIVE
(Red tubing) side on the pressure switch and SIDE of the collector box.
FIGURE 31
Page 36
To troubleshoot the pressure switch, temporarily jumper the D−Blower Compartment (Figures 33 and 34)
switch. The unit will not fire with pressure switch jumpered.
Therefore, the pressure switch must be bypassed after the Blower motor (B3), capacitor (C4), and secondary limit con-
combustion air blower is activated. This will determine if the trol (S21) are located in the blower compartment shown in
pressure switch and furnace are operating properly. However, figure 33. Blower motor (B3), Coil choke (L13) and secon-
this may not indicate if the sealed combustion system is oper- dary limit (S21) are shown in figure 34. The blower compart-
ment can be accessed by removing the blower access pan-
ating properly. If the unit cannot attain 0.75" W.C. (186.48 Pa )
el.
differential, the unit will not operate.
IMPORTANT BLOWER COMPARTMENT

Unit will not operate with pressure switch bypassed Q MODELS
SECONDARY LIMIT
upon start-up. To troubleshoot pressure switch, CONTROL (S21)
jumper pressure switch following activation of com-
bustion air blower!!
Checks of pressure differential can aid in troubleshooting.

When measuring the pressure differential, readings should be
taken at the pressure switch. Lack of differential usually indi-
cates problems in the intake or exhaust piping, but may indi-
cate problems in the heat exchanger, condensing coil,
header boxes, combustion blower or other compo-
nents.
Measuring pressure differential
The differential pressure is the difference in pressure mea-
sured on either side of the pressure switch:
1 − Remove thermostat demand and allow unit to cycle
BLOWER MOTOR
off. BLOWER MOTOR CAPACITOR (C4)
(B3)
2 − Disconnect hose from front of pressure switch and
install tee as shown in figure 32. Repeat sequence for FIGURE 33
hose connected to back of switch.
TEE AND 1/4"i.d. RUBBER HOSE FIELD PROVIDED
TO PRESSURE
SENSING HOSE BLOWER COMPARTMENT
TO PRESSURE V MODELS
SWITCH
SECONDARY
LIMITS (S21)
TO DRAFT GAUGE
FIGURE 32
3 − Install manometer (draft gauge) to open ends of tee’s.

The hose from the back side of the switch goes to the
zero side of the gauge.
4 − Operate unit and observe draft gauge reading. Read-
ings will change as heat exchanger warms.
a. Take one reading immediately after startup.
b. Take a second reading after unit has reached steady
state (approximately 5 minutes). BLOWER
COIL WHEEL BLOWER
Pressure differential should be greater than .75" CHOKE MOTOR (B3)
W.C. (186.48 Pa). (L13)
To Remove Blower From Unit: Remove Bolts and
5 − Remove thermostat demand and allow to cycle off. Wiring Jackplugs. Then Slide Out Front of Unit.
6 − Remove draft gauge and Tee’s. Reinstall combustion air FIGURE 34

sensing hoses to the pressure switch.
Page 37
1.Blower Motor (B3) and Capacitor (C4) GHR32V BLOWER MOTOR B3
GHR32Q Models J48
SHAFT
All GHR32Q model units use single phase direct drive blow-
er motors. All motors are 120V permanent split capacitor
motors to ensure maximum efficiency. See motor name-
plate or SPECIFICATIONS section for motor ratings. Rat- MOTOR
J49
ings for capacitor will be on side. CONTROLLER
2.Secondary Limit Control (S21) FIGURE 36

GHR32V BLOWER MOTOR COMPONENTS
The secondary limit (S21) on GHR32 units is mounted on STATOR
the back side of the blower housing. When excess heat is (WINDINGS)
sensed in the blower compartment, the limit will open. If the BEARING
limit is tripped, the furnace control energizes the supply air OUTPUT
blower and closes the gas valve. The limit automatically resets SHAFT
when unit temperature returns to normal. The switch opens at
160_F + 5_F (71.1_C + 2.8_C) on a temperature rise and re- ROTOR
sets at 130_F + 8_F (54.4_C + 4.4_C) on a temperature fall. FIGURE 37

The switch is factory set and cannot be adjusted. The setpoint A solid-state controller is attached to the motor. The
is printed on the face plate of the limit. controller is primarily an A.C. to D.C. converter. Con-
verted D.C. power is used to drive the motor. The con-
SECONDARY LIMIT CONTROL (S21) troller contains a microprocessor which monitors vary-
ing conditions inside the motor (such as motor
SPADE CONNECTORS
workload).
The controller uses sensing devices to sense what position
LIMIT
the rotor is in at any given time. By sensing the position of the

rotor and then switching the motor windings on and off in se-
INSULATING COVER (s) quence, the rotor shaft turns the blower.
FIGURE 35 GHR32V series blower motor ratings are listed in the

SPECIFICATIONS section. All GHR32V blower motors
3. Blower Motor (B3) GHR32V MODELS use single phase power. An external run capacitor is not
used. The motor uses permanently lubricated ball-type
GHR32V model units use a single−phase, electronically con- bearings. The VSM is a two part component; the motor
trolled D.C. brushless motor (controller converts single phase and the control module. If motor fails, it is quite possible
A.C. to three phase D.C.), with a permanent-magnet-type ro- the control module only, will need to be replaced. Len-
tor (figure 36). Because this motor has a permanent magnet nox provides a replacement kit for the control module.
rotor it does not need brushes like conventional D.C. motors. Internal Operation
Internal components are shown in figure 37. The stator wind- Each time the controller switches a stator winding (figure 37)
ings are split into three poles which are electrically connected on and off, it is called a pulse." The length of time each pulse
to the controller. This arrangement allows motor windings to stays on is called the pulse width." By varying the pulse width
turn on and off in sequence by the controller. (figure 38), the controller varies motor speed (called pulse-
width modulation"). This allows for precise control of motor
DANGER speed and allows the motor to compensate for varying load
conditions as sensed by the controller. In this case, the control-
Disconnect power from unit and
wait at least five minutes to allow ler monitors the static workload on the motor and varies motor
capacitors to discharge before at- rpm in order to maintain constant airflow (cfm).
tempting to adjust motor speed tap
settings. Failure to wait may cause The motor is equipped with 11 incremental taps which are driv-
personal injury or death. en by the integral controller. The controller is capable of con-
trolling three of the 11 taps.
Page 38
The motor controller is driven by the VSP2−1, VSP3−1 or Motor Start-Up
two stage integrated SureLight control The VSP re- When B3 begins start-up, the motor gently vibrates back and
ceives its demand (PWM signal or fixed 24 VAC or VDC forth for a moment. This is normal. During this time the elec-
signal) from optional controls such as the Harmony zone con- tronic controller is determining the exact position of the rotor.
trol system, Efficiency Plus Humidity Control (CCB1) or a con- Once the motor begins turning, the controller slowly eases
ventional thermostat. the motor up to speed (this is called soft-start"). The motor
Motor rpm is continually adjusted internally to maintain may take as long as 10-15 seconds to reach full speed. If the
constant static pressure against the blower wheel. The control- motor does not reach 200rpm within 13 seconds, the motor
ler monitors the static work load on the motor and motor amp- shuts down. Then the motor will immediately attempt a re-
draw to determine the amount of rpm adjustment. Blower rpm start. The shutdown feature provides protection in case of a
may be adjusted any amount in order to maintain a constant frozen bearing or blocked blower wheel. The motor may at-
cfm as shown in Blower Ratings Tables. The amount of adjust- tempt to start eight times. If the motor does not start after the
ment is determined by the incremental taps which are used eighth try, the controller locks out. Reset controller by momen-
and the amount of motor loading sensed internally. The cfm tarily turning off power to unit.
remains relatively stable over a broad range of static pressure. The DC filter capacitors inside the controller are connected
Since the blower constantly adjusts rpm to maintain a specified electrically to the speed tap wires. The capacitors take
cfm, motor rpm is not rated. Hence, the terms blower speed" approximately 5 minutes to discharge when the dis-
and speed tap" in this manual, on the unit wiring diagram and connect is opened. For this reason it is necessary to
on blower B3 refer to blower cfm regardless of motor rpm. wait at least 5 minutes after turning off power to the
When Harmony is used, speed taps are overridden and a unit before attempting to change speed taps.
PWM signal generated by the Harmony controller continuous-
ly varies motor speed based upon zone demands.
Initial Power Up
When line voltage is applied to B3, there will be a large inrush
of power lasting less than 1/4 second. This in rush charges a
bank of DC filter capacitors inside the controller. If the discon-
nect switch is bounced (rapid turning on and off) when the dis-
connect is closed, the disconnect contacts may become
welded. Try not to bounce the disconnect switch when apply-
ing power to the unit.
Page 39
MOTOR SPEED CONTROL WITH D.C. PULSE-WIDTH MODULATION
Motor speed is determined by the size of the electrical pulse sent to the
motor windings. The longer the pulse, the faster the motor.
OUTPUT FROM CONTROLLER TO MOTOR WINDINGS
ÇÇ ÇÇ
WINDINGS TURNED OFF WINDINGS TURNED ON
ÇÇ ÇÇ
ON PULSE OFF PULSE
The frequency of the pulses to the windings is 20KHz.

DO NOT ATTEMPT TO MEASURE THESE VOLTAGES.
LOW SPEED HEAT/COOL (output from controller to motor windings)
One
Pulse
325VDC ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
One revolution
ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
O volts
WINDING #1
325VDC
O volts ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
WINDING #2
325VDC
O volts
WINDING #3
HIGH SPEED HEAT (output from controller to motor windings)
One revolution
325VDC
O volts
WINDING #1
325VDC
O volts
WINDING #2
325VDC
O volts
WINDING #3
HIGH SPEED COOL (output from controller to motor windings)
325VDC ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
One revolution
ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
O volts
WINDING #1
325VDC
O volts ÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇÇ
WINDING #2
325VDC
O volts
WINDING #3
FIGURE 38
Page 40
External Operation (Speed Tap Priority) 4.Choke Coil (L13)
Figure 39 shows the two quick-connect jacks (J48 and J49) A choke coil is used on all GHR32V units. The choke is
which connect the motor to the GHR32V. Jack J48 is the located on the blower housing and is used to block radio fre-
power plug and jack J49 connects the unit controls to the quency interference.
motor.
Precautions
Line voltage must be applied to J48 pin 5 in order for the
motor to operate. When using 120VAC pins 1 and 2 must If the GHR32 V or its electronically controlled blower motor is
be jumpered. When control voltage is applied to J49 pin 3 improperly or inadequately grounded, it may cause television
and 15 (single stage heating and cooling), the motor is en- interference (commonly known as RFI or radio frequency in-
ergized on the low speed heat/cool tap. terference).
When voltage is applied to J49 pin 2 in addition to pin 3 and This interference is caused by internal switching fre-
15 (second stage heating), the blower is energized on the quencies of the motor controller (see figure 40). TV in-
high speed heating tap. When voltage is applied to J49 pin terference may show up as small specks or lines which
10 in addition to pin 3 and 15 (second stage cooling), the randomly appear on the TV screen accompanied by pops or
blower is energized on the high speed cooling tap. The mo- clicks in the sound. Before attempting any service, make sure
tor assigns priority to J49 pin 2 so that if a call for cooling and a the indoor unit is causing the interference. To check, discon-
call for heating are concurrent, heating call overrides and the nect power to indoor unit then check TV for continued signs of
blower operates on high speed heating tap. interference.
ICM2 with VSP3 or Two stage Variable Speed Control TV interference may be stopped by making sure the mo-
The ICM2 operates slightly different than stated above tor is solidly grounded to the cabinet (metal to metal) and
when matched with the VSP3 or Two stage variable speed by making sure the cabinet is solidly grounded. If TV in-
control. When control voltage is applied to J49 pin 3 and 15, terference persists, make sure the television (and all af-
the motor is energized on continuous fan. When voltage is fected RF appliances) are moved away from the GHR32V.
applied to J49 pin 2 in addition to pin 3 and 15 (first stage Also make sure affected appliances are connected to a sepa-
heating), the blower is energized on the low speed heating rate electrical circuit.
tap. When voltage is applied to J49 pin 13 in addition to pin
3 and 15 (second stage heating), the blower is energized
on the high speed heating tap. The motor assigns priority to ECM SWITCHING FREQUENCY
J49 pin 2 so that if a call for cooling and a call for heating are The electrical pulses to the windings cycle on and off at a rate of
20,000 cycles per second (20Khz, this is called the switching
concurrent, heating call overrides and the blower operates frequency). The effective D.C. voltage can be varied by chang-
on high speed heating tap. ing the pulse width. The switching frequency is necessary in
order to vary the speed of the motor. If the motor is not securely
grounded to the cabinet and if the cabinet is not securely
grounded, the switching frequency may cause television inter-
BLOWER B3 HARNESS CONNECTORS ference.
POWER CONTROL OUTPUT FROM CONTROLLER TO MOTOR WINDINGS
J49
CONNECTOR J48 CONNECTOR J49 PIN 1 - C1
ÇÇÇÇÇÇÇÇÇÇÇÇÇ
One Pulse One cycle
PIN 2 - W / W1 325VDC
PIN 3 - C2
1 1 4 − Delay
PIN O volts
PIN 5 - Cool WINDING #1
325VDC
PIN 6 - Y1
PIN 7 - Adjust O volts
PIN 8 - 0ut WINDING #2
325VDC
PIN 9 - 0
PIN 10 - BK / PWM O volts
PIN 11 - Heat WINDING #3
ÇÇ
PIN 12 - R PULSE ON ONE
PIN 13 - EM / W2
ÇÇ
ELECTRICAL
PIN 14 - Y / Y2 PULSE OFF PULSE
ÇÇ
PIN 15 - G 325VDC
PIN 16 - Out + WINDING OFF
J48
PIN 1 - Jumper PIN 1 to PIN2 for 120VAC line input only. O volts
PIN 2 - Jumper PIN 1 to PIN2 for 120VAC line input only.
PIN 3 - Ground Switching Frequency
20Khz
PIN 4 - AC Line
PIN 5 - AC Line
FIGURE 40
FIGURE 39
Page 41
II−PLACEMENT AND INSTALLATION B−Venting Considerations
Make sure unit is installed in accordance with installation in- All GHR32 furnaces must be vented independently as
structions and applicable codes. shown in figure 42 and must not be connected to a com-
mon venting system. If a GHR32 furnace replaces a less
efficient furnace which was vented with other gas ap-
A−PVC Joint Cementing Procedure
pliances into a common vent, the size of the common vent
pipe must be appropriate for gas appliances which remain
WARNING connected. Without the heat of the original furnace flue prod-
DANGER OF EXPLOSION! Fumes from PVC glue ucts, the vent pipe is probably oversized for the single water
may ignite during system check. Remove spark heater or other appliance(s). The common vent should be
plug wire from ignition control before 120V power checked for proper draw for all appliance(s) which remain
is applied. Reconnect wire after two minutes.
connected.
1 − Measure and cut vent pipe to desired length.

Checks of Common Venting System
2 − Debur and chamfer end of pipe, removing any for Other Gas Appliances (Water Heater, etc...)
ridges or rough edges. If end is not chamfered, edge
1 − Unused openings in the common venting system must be
of pipe may remove cement from fitting socket and
sealed.
result in a leaking joint.
2 − The venting system should be visually checked for proper
3 − Clean and dry surfaces to be joined. size and horizontal pitch. You should also check and de-
4 − Test fit joint and mark depth of fitting on outside of termine that there is no blockage or restriction, leakage,
pipe. corrosion and other deficiencies which could cause an un-
safe condition.
5 − Uniformly apply liberal coat of PVC primer for PVC or
ABS cleaner for ABS to inside socket surface of fitting 3 − Close all building doors and windows and all doors
and male end of pipe to depth of fitting socket. between the space in which the appliances remaining
connected to the common venting system are located
6 − Promptly apply solvent cement to end of pipe and in-
and other spaces of the building. Turn on clothes dryers
side socket surface of fitting. Cement should be ap-
and any appliances not connected to the common vent-
plied lightly but uniformly to inside of socket. Take care
ing system. Turn on any exhaust fans, such as range
to keep excess cement out of socket. Apply second
hoods and bathroom exhausts, so they will operate at
coat to end of pipe.
maximum speed. Do not operate a summer exhaust fan.
NOTE−Time is critical at this stage. Do not allow primer Close fireplace dampers.
to dry before applying cement.
4 − Follow the lighting instructions. Place the appliance being
7 − Immediately after applying last coat of cement to pipe, inspected in operation. Adjust thermostat so appliance will
and while both inside socket surface and end of pipe operate continuously.
are wet with cement, forcefully insert end of pipe into 5 − Test for spillage at the draft hood relief opening after 5
socket until it bottoms out. Turn pipe 1/4 turn during minutes of main burner operation. Use match or candle
assembly (but not after pipe is fully inserted) to dis- flame, or smoke from a cigarette or cigar.
tribute cement evenly. Once joint is made, PVC may
6 − After it has been determined that each appliance re-
swell. Hold joint together until bonded (approxi-
maining connected to the common venting system
mately 20 seconds).
properly vents when tested as outlined above, return
NOTE−Assembly should be completed within 20 sec- doors, windows, exhaust fans, fireplace dampers and any
onds after last application of cement. Hammer blows other gas-burning appliance to their previous condition of
should not be used when inserting pipe. use.
7 − If improper venting is observed during any of the tests, the
8 − After assembly, wipe excess cement from pipe at
common venting system must be corrected. The com-
end of fitting socket. A properly made joint will show
mon venting system should be resized to approach the
a bead around its entire perimeter. Any gaps may in-
minimum size as determined by using the appropriate
dicate a defective assembly due to insufficient sol-
tables in appendix G in the current standards of the Na-
vent.
tional Fuel Gas Code in the U.S.A. or category 1 in the
9 − Handle joints carefully until completely set. Natural Gas and Propane Installation Code in Canada.
Page 42
GHR32 Intake and Exhaust Piping Considerations 5 − Exhaust piping must terminate straight out or up as
shown. On roof terminations, the intake piping
should terminate straight down using two 90_ elbows
If the GHR32 venting system must be altered or repaired, use
(See figure 42). In rooftop applications, a 2" X 1−1/2"
the following as a guide. Intake and exhaust pipes may be
(51mm X 38mm) reducer for 2" (51mm) venting, 3" x 2"
routed either horizontally through an outside wall or verti-
(76mm X 51mm) reducer for 3" (76mm) venting must be
cally through the roof. In attic or closet installations, vertical
used on exhaust piping at the point where it exits the
termination through the roof is preferred. Figures 42 through
structure to improve the velocity of exhaust and force flue
45 show typical terminations.
products away from intake piping.
1 − Use only recommended piping materials for both in-
take and exhaust piping. NOTE-Care must be taken to avoid recirculation of ex-
haust back into intake pipe.
2 − Secure permanent joints gas tight using approved ce-
ment.
6 − On side wall exits, exhaust piping should extend a
3 − Piping diameters should be determined according to maximum of 12" (395mm) beyond the outside wall.
length of pipe run. See table 31. Locate intake piping Intake piping should be as short as possible. See
upwind (prevailing wind) from exhaust piping. To avoid figure 44.
recirculation of exhaust gas on roof terminations, end of 7 − Minimum separation distance between the end of
exhaust pipe must be higher than intake pipe. the exhaust pipe and the end of the intake pipe is 8"
Exhaust and intake exits must be in same pressure (203mm).
zone. Do not exit one through the roof and one 8 − If intake and exhaust piping must be run up a side wall
through the side. Also, do not exit the intake on one to position above snow accumulation or other ob-
side and the exhaust on another side of the house or structions, refer to figure 45 for proper piping method.
structure. Piping must be supported every 3 ft. (.91m) as shown in
figure 41 and must be insulated. When exhaust and intake
4 − Intake and exhaust pipes should be placed as close
piping must run up an outside wall, the exhaust piping is
together as possible at termination end (refer to il-
reduced accordingly after the final elbow.
lustrations). Maximum separation is 3" (76mm) on roof
terminations and 6" (152mm) on side wall termina- 9 − Position termination ends so they are free from any ob-
tions. structions and above snow accumulation level (where ap-
plicable). Termination ends must be a minimum of 12"
NOTE−If winter design temperature is below 32_ F (0_C), (305mm) above grade level. Do not point into window
exhaust piping must be insulated with 1/2" (13mm) Ar- wells, stairwells, alcoves, courtyard areas or other re-
maflex or equivalent when run through unheated cessed areas. Do not position termination ends directly
space. Do not leave any surface area of exhaust pipe below roof eaves.
open to outside air; exterior exhaust pipe must be insu- 10− Suspend piping using hangers at a minimum of every
lated with 1/2" (13mm) Armaflex or equivalent. In ex- 5 feet (1.52m) for schedule 40 PVC and every 3 feet
treme cold climate areas, 3/4" (19mm) Armaflex or (.91m) for ABS−DWV, PVC−DWV, SDR−21 PVC, and
equivalent is recommended. Insulation on outside SDR−26 PVC piping. A suitable hanger can be fabri-
runs of exhaust pipe must be painted or wrapped to cated by using metal or plastic strapping or a large wire tie.
protect insulation from deterioration. See figure 41.
Page 43
METAL OR PLASTIC 60G77 For 2 inch (51 mm) Venting
STRAPPING 33K97 For 3 inch (76 mm) Venting
2 x 1-1/2 in. (51 x 38 mm) 60G77
3 x 2 in. (76 x 51 mm) 33K97
REDUCER BUSHING (Furnished)
37
(940)
FIGURE 41 INTAKE AIR
3 (76)
11− In areas where piping penetrates joists or interior walls,
hole must be large enough to allow clearance on all INTAKE AIR EXHAUST
sides of pipe through center of hole using support CLAMP AIR
straps. ELBOW (Furnished) TERMINATION ASSEMBLY
(Furnished) (Furnished)
12− Isolate piping at the point where it exits the outside wall
60L46 For 3 inch (76 mm) Venting
or roof.
46−3/4
13− Unit should not be installed in areas normally sub- (1187)
6−1/2
ject to freezing temperatures. (165)
14− When furnace is installed in a residence where unit is
4−1/2 (114)
shut down for an extended period of time, such as a
vacation home, make provisions for draining exhaust
INTAKE AIR
tee, cold end header collector box, condensate collection
trap and lines. ELBOW TERMINATION ASSEMBLY EXHAUST
(Field Supplied) (Furnished) AIR
Intake Piping Requirements
Piping must be routed to outside of structure.
CONCENTRIC WALL TERMINATION APPLICATIONS
Cat. No. A
IMPORTANT 60G77 10-1/2 (267) max. A
33K97 10-1/2 (267) max.
Combustion air intake inlet and exhaust outlet 60L46 7−1/2 (191) max.
INTAKE
should not be located within 6 ft. (1.8m) of dryer AIR
EXHAUST EXHAUST
vent or combustion air inlet or outlet of another ap- AIR AIR
pliance. Piping should not exit less than 3 ft. (.91m)
from opening into another building.
INTAKE INTAKE 12 (305)

OUTSIDE Minimum
AIR WALL AIR
Above
ÉÉÉÉÉÉÉÉ
ROOF TERMINATION KITS Grade
15F75 For 2 inch (51 mm) Venting GRADE
44J41 For 3 inch (76 mm) Venting
3 in. MAX. CONCENTRIC ROOF TERMINATION APPLICATIONS
(76 mm)
FLASHING
INTAKE PIPE 8 (203) 12 (305)
Not Furnished) Minimum Minimum
Above Average
Snow
FLASHING Accumulation
(2)
12 (305) (Furnished)
Minimum
Above SHEET METAL STRAP
Average 2 x 1-1/2 in.
Snow (Clamp and sheet metal strap
(51 x 38 mm) 15J75
Accumulation must be field installed to support
or 3 x 2 in.
(76 x 51 mm) 44J41 the weight of the termination kit.)
REDUCER BUSHING CLAMP
(Not Furnished)
EXHAUST PIPE
(Not Furnished)
INSULATION ARMAFLEX
SLEEVES (2) INSULATION FIGURE 43
(Furnished) (Not Furnished)
FIGURE 42
Page 44
NOTE 12 in. (305 mm) minimum height above WALL TERMINATION KIT (RING KIT)
average snow accumulation. 15F74 For 2 inch (51 mm) Venting
NOTE Not for use with 3 inch (76 mm) Venting
12 in. (305 mm) maximum
NOTE EXHAUST PIPE SHOWN

6 in. (152 mm)
8 in. (203 mm) maximum
minimum INSULATION SLEEVE
(2 Furnished 1 for intake and 1 for exhaust)
Typical Application STAINLESS STEEL OUTSIDE SEAL CAP
(2 Furnished 1 for intake and 1 for exhaust)
GALVANIZED STEEL INSIDE SEAL CAP
(2 Furnished 1 for intake and 1 for exhaust) 2 in. (51 mm) PVC
(Not Furnished)
PVC COUPLING
(Not Furnished)
SEAL RINGS (4 Furnished 2 x 1-1/2 in. (51 x 38 mm)

ARMAFLEX INSULATION
2 for intake and 2 for exhaust) REDUCER BUSHING
(Not Furnished)
(Not Furnished)
FIGURE 44
INDOOR 2 x 1-1/2 in. (51 x 38 mm) 22G44

EXHAUST ASSEMBLY 3 x 2 in. (76 x 51 mm) 44J40
(Furnished) *REDUCER BUSHING
(Furnished) WALL TERMINATION KITS (CLOSE-COUPLE)
GASKET
(Furnished) 22G44 For 2 inch (51 mm) Venting
44J40 For 3 inch (76 mm) Venting
OUTDOOR
EXHAUST ASSEMBLY
(Furnished)
INDOOR If Intake and Exhaust Pipe is less than
INTAKE ASSEMBLY
(Furnished) 12 in. (305 mm) above snow accumula-
tion or other obstructions, field fabri-
2 in. (51 mm) COUPLING
(Furnished)
INTAKE cated piping must be installed.
AIR
*Bushing outside on plate FACE PLATE EXHAUST EXHAUST

for 44J40 kit. (Furnished) AIR AIR
12
(305)
INSULATION
(Not Furnished) INTAKE
INTAKE AIR
AIR
EXHAUST
AIR
5 (127)
2 12 (305
(51) Minimu
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
12 12 ABOVE GR
(305) (305)
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
5-1/2 GRADE
(140)
FIGURE 45
Page 45
TABLE 31
VENTING REQUIREMENTS
Model No. GHR32−50 GHR32−75 GHR32−100 GHR32−120
Vent Pipe Minimum Equivalent Length with Accelerator − Exhaust pipe should
20 ft. (6.1 m) 20 ft. (6.1 m) 15 ft. (4.6 m) 15 ft. (4.6 m)
terminate with an accelerator. See Termination Kits, below.
feet (m) Minimum Vent Pipe Diameter Required
15 (4.6) Not Recommended 2 in. (51 mm)
20 (6.1)
25 (7.6) 3 in. (76 mm)
30 (9.1) 2 in. (51 mm)
35 (10.7)
M i
Maximum E
Equivalent
i l tV Ventt L
Length
th 2 in.
in (51 mm)
40 (12.2) 3 in. (76 mm)
45 (13.7)
Maximum length is for one individual
run, either intake or exhaust. 50 (15.2)
55 (16.8)
60 (18.3) Not Available
3 in.
in (76 mm)
70 (21.3)
80 (24.4) 3 in. (76 mm)
Not Available
90 (27.4)
100 (30.5)
VENT/INTAKE AIR TERMINATION KIT USAGE
Cat. No.
Roof Kit (15F75) Acceptable
Kits for 2 in. (51
( mm)) Wall Ring Kit (15F74)
Venting Acceptable Acceptable Not Available
Closed Couple Wall Kit
Acceptable
NOTE − Exhaust pipe (22G44)
must bbe terminated
i d with
ih Concentric Roof/Wall Kit (60G77) Not Available
Termination Kits an accelerator; 1−1/2
1 1/2 in.
in
(38.1 mm) diameter pipe, Closed Couple Wall Kit
NOTE − Intake 12 in. (305 mm) in length. (30G28)
Acceptable Acceptable Not Available Not Available
and Exhaust
Closed Couple Wall Kit with
p p must be the
pipes extension riser (30G79)
same Cat. No.
diameter
diameter. Kits for 3 in
in. (76 mm)
Venting Concentric Roof/Wall Kit (60L46) Not Available Acceptable
Vent/Intake Air Roof Kit
NOTE − Exhaust pipe (44J41)
must be terminated with Acceptable
an accelerator; 2 in. (51 Closed Couple Wall Kit Acceptable Acceptable Acceptable
mm)) diameter p p , 12 in. (44J40)
pipe,
(305 mm) in length.
length Concentric Roof/Wall Kit (33K97) Acceptable
2 in. (51 mm) pipe may be used to adapt terminations and intake/exhaust furnace connections. The TOTAL of 2 in. (51 mm) pipe that can be used
CANNOT exceed 3 feet (1 m).
Equivalent Vent Lengths:
10 ft. (3 m) and two 90° elbows of 2 in. (51 mm) pipe equals 20 ft. (6.1 m).
5 ft. (1.5 m) and two 90° elbows of 2 in. (51 mm) pipe equals 15 ft. (4.6 m).
5 ft. (1.5 m) and two 90° elbows of 3 in. (76 mm) pipe equals 15 ft. (4.6 m).One 90_elbow equals 5 feet (1.5 m) of straight vent pipe.
One 45_ elbow equals 2.5 feet (.75 m) of straight vent pipe.
When additional/field supplied venting is used to clear average snow accumulation, the additional length of pipe and elbows must be figured into
the Maximum Equivalent Vent Length/Minimum Vent Pipe Diameter Requirements.
90° intake elbow CANNOT be used in this application.
12 feet (3.6 m) of additional vent must be figured into the Maximum Equivalent Vent Length/Minimum Vent Pipe Diameter Requirements if this kit is
used.
Only used with minimum vent length.
Exhaust Piping Requirements

This unit is designed for left or right air exhaust piping for the CAUTION
down-flow configuration. In horizontal applications, flue piping Do not discharge exhaust into an existing stack or
must exit the top side of the unit. stack that also serves another gas appliance. If
vertical discharge through an existing unused
All horizontal runs of exhaust pipe must slope toward unit. stack is required, insert PVC pipe inside the stack
A minimum of 1/4" (6mm) drop for every 12" (305mm) of until the end is above the top or outlet end of the
horizontal run is mandatory for drainage. Horizontal runs of metal stack.
exhaust piping must be supported every 5 ft. (1.5m) [3 ft.
(0.9m) for ABS and SDR] using hangers. CAUTION
NOTE−Exhaust piping must be installed on the same The exhaust vent pipe operates under positive
side as the condensate trap. pressure and must be completely sealed to pre-
vent leakage of combustion products into the
NOTE−Exhaust piping should be checked carefully to living space.
make sure there are no sags or low spots.
Page 46
Condensate Piping Requirements 5 − Install a tee and vent pipe in the drain line near the trap.
The GHR32 unit is designed for either left or right con- Top of vent pipe should be 7" (178mm) above drain
densate plumbing in the down-flow configuration. In the level on trap.
horizontal position, trap should extend below unit; pro- 6 − Condensate line must be sloped downward away from
vide for a 3-3/4" (92mm) service clearance. Condensate trap (a minimum of 1/4" [6mm] drop for each 12"
drain line should be routed only within the conditioned [305mm] of horizontal line) to drain. If drain level is
space to avoid freezing of condensate and blockage of above condensate trap, condensate pump must be
drain line. An electric heat cable should be used where used in condensate line.
condensate piping is exposed to unconditioned areas. If
condensate piping needs to be relocated to another position
or removed for service, use the following procedure to reinstall. III−START-UP
A−Preliminary and Seasonal Checks
CAUTION 1 − Inspect electrical wiring, both field and factory installed
Do not use copper tubing or existing copper for loose connections. Tighten as required.
condensate lines for drain line. 2 − Check voltage at disconnect switch. Voltage must be with-
in range listed on the nameplate. If not, consult the power
1 − Determine the side the condensate trap is to be installed. company and have voltage condition corrected be-
Remove temporary plugs from condensate collar on fore starting unit.
which the condensate trap is to be installed.
3 − Inspect condition of condensate traps and drain as-
CONDENSATE ASSEMBLY
sembly. Disassemble and clean seasonally.
(Right Side Installation Shown)
B−Heating Start-Up
CONDENSATE
COLLAR FOR YOUR SAFETY READ BEFORE LIGHTING
CONDENSATE
DRAIN LINE
CONNECTION WARNING
(route line to one side
glue cap to unused side) Do not use this furnace if any part has been under-
water. Inspect the furnace and replace any part of
the control system and any gas control which has
been under water.
STEMS
CONDENSATE
TRAP
DRAIN DRAIN PLUG
PLUG CAP WARNING
FIGURE 46
If overheating occurs or if gas supply fails to shut
off, shut off the manual gas valve to the appliance
CAUTION before shutting off electrical supply.
Condensate trap must be installed on the same
side as exhaust piping in downflow applica-
tions and on bottom of unit in horizontal ap-
plications. CAUTION
Before attempting to perform any service or
2 − Apply glue to condensate trap stems and insert trap maintenance, turn the electrical power to unit
into holes provided in condensate collar. Make sure OFF at disconnect switch.
condensate trap is completely sealed to avoid any
leaks. Use the provided 1/2" screw to secure the top
BEFORE LIGHTING smell all around the appliance area
of the condensate trap to the side of the unit. See
for gas. Be sure to smell next to the floor because some gas
figure 46. is heavier than air and will settle on the floor.
3 − For downflow applications only, remove plugs from the Use only your hand to push in or turn the gas control knob.
unused condensate collar on the opposite side of the Never use tools. If the knob will not push in or turn by hand,
unit. Apply glue to the plugs and place them back into do not force. Force or attempted repair may result in a fire
the condensate collar. or explosion.
4 − Glue the drain line (field provided) to the trap. Route GHR32 units are equipped with a hot surface ignition
drain line to an open drain. Glue 1" (25mm) cap (pro- system. Do not attempt to manually light burners on
vided on trap) on unused condensate drain line con- these furnaces. Each time thermostat calls for heat, the
nection. burners will be automatically lit.
Page 47
How To Operate Gas Valve Refer to Maintenance" section of this manual for instruc-
tions on how to prepare condensate assembly for ex-
WARNING tended period shutdown.
IV−HEATING SYSTEM SERVICE CHECKS
If you do not follow these instructions exactly, a
fire or explosion may result causing property A−A.G.A./C.G.A. Certification
damage, personal injury or loss of life.
All units are A.G.A. and C.G.A. design certified without
modifications. Refer to the GHR32 Operation and Installa-
1 − STOP! Read the safety information at the beginning of tion Instruction Manual Information.
this section.
B−Gas Piping
2 − Set thermostat to lowest setting.
Gas supply piping should not allow more than 0.5"W.C. drop
3 − Turn off all electrical power to furnace.
in pressure between gas meter and unit. Supply gas pipe
4 − This appliance is equipped with an ignition device must not be smaller than unit gas connection.
which automatically lights the burner. Do not try to
Compounds used on gas piping threaded joints should be
light the burner by hand.
resistant to action of liquefied petroleum gases.
5 − Remove unit access panel.
C−Testing Gas Piping
6 − Natural valve, move lever to OFF. Propane valve,
turn knob to OFF. Do not force. When pressure testing gas lines, the gas valve must be dis-
7 − Wait five (5) minutes to clear out any gas. If you then connected and isolated. Gas valves can be damaged if
smell gas, STOP! Immediately call your gas supplier from subjected to more than 0.5psig (14" W.C.). See figure 47. If
a neighbor’s phone. Follow the gas supplier’s instruc- the pressure is equal to or less than 0.5psig (14"W.C.), use
tions. If you do not smell gas go to next step. the manual shut−off valve before pressure testing to isolate
8 − Natural valve, move lever to ON. Propane valve, turn furnace from gas supply.
knob to ON. Do not force.
9 − Replace access panel. GAS PIPING TEST PROCEDURE (Typical)
10− Turn on all electrical power to unit.
11− Set thermostat to desired setting. MANUAL MAIN SHUT−OFF
VALVE WILL NOT HOLD FURNACE
12− If the appliance will not operate, follow the instructions NORMAL TEST PRESSURE
To Turn Off Gas To Unit" and call your service techni-
1/8" N.P.T. ISOLATE
cian or gas supplier. GAS VALVE
PLUGGED TAP
Turning Off Gas To Unit
CAP
1 − Set thermostat to lowest setting.
2 − Turn off all electrical power to unit if service is to be per-
formed.
3 − Remove access panel.
4 − Natural valve, move lever to OFF. Propane valve, turn FIGURE 47
knob to OFF. Do not force.
5 − Replace access panel. IMPORTANT
NOTE−On initial start−ups and when condensate trap is In case emergency shutdown is required, turn off
dry, unit may turn itself off and on to allow condensate the main shut-off valve and disconnect the main
trap to fill. This is normal operation. power to unit. These controls should be properly
labeled by the installer.
C−Safety or Emergency Shutdown
Turn off unit power. Close manual and main gas valves. When checking piping connections for gas leaks, use
D−Extended Period Shutdown preferred means. Kitchen detergents can cause harmful
Turn off thermostat or set to UNOCCUPIED" mode. Close corrosion on various metals used in gas piping. Use of a spe-
all gas valves (both internal and external to unit) to guaran- cialty Gas Leak Detector is strongly recommended. It is
tee no gas leak into combustion chamber. Turn off power to available through Lennox under part number 31B2001.
unit. All access panels, covers and vent caps must be in Do not use matches, candles, flame or any other source of
place and secured. ignition to check for gas leaks.
Page 48
gas to the unit. Normal manifold operating pressure for
TOP natural gas units is 2.5 to 3.5" W.C. (621 to 870 Pa). See
MANUAL MAIN
SIDE SHUT−OFF
figure 29. For LP/propane gas the correct manifold operat-
PIPING VALVE ing pressure is 9.0 to 10.0" W.C. (2.24 to 2.49 Pa). See fig-
ure 30.
1/8" NPT
PLUGGED
TAP
GAS VALVE
IMPORTANT
MANUAL MAIN For safety, connect a shut-off valve between the
SHUT−OFF manometer and the gas tap to permit shut off of
VALVE gas pressure to the manometer.
1/8" NPT
PLUGGED TABLE 32
BOTTOM TAP
SIDE GAS VALVE REGULATION*
Unit (Fuel) Absolute Pressure (outlet) in. W.C.
PIPING
Natural 3.5
LEFT SIDE RIGHT L.P. 10.0
MANUAL SIDE
MAIN PIPING MANUAL
SHUT−OFF
PIPING MAIN The gas valve is factory set and should not require adjustment.
VALVE SHUT−OFF See table 32. Also, gas valve regulation varies with burner box
GAS VALVE VALVE
pressure (figures 29 and 30).
*Manifold Absolute Pressure Measurement and Adjust-
ment
1 − Connect test gauge to outlet tap on gas valve.
1/8" NPT 1/8" NPT 2 − Disconnect pressure sensing hose from gas valve
PLUGGE PLUGGE
D D and plug hose by covering opening with tape or
TAP TAP equivalent. Leave hose barb on valve open to atmo-
FIGURE 48 sphere.
3 − Start unit and allow 5 minutes for unit to reach steady
D−Testing Gas Supply Pressure state.
When testing supply gas pressure, connect test gauge to 4 − While waiting for the unit to stabilize, notice the flame.
inlet pressure tap (field provided). See figure 48. Check gas Flame should be stable and should not lift from burner.
line pressure with unit firing at maximum rate. Low pres- Natural gas should burn blue. L.P. gas should burn
sure may result in erratic operation or underfire. High mostly blue with some orange streaks.
pressure can result in permanent damage to gas valve 5 − After allowing unit to stabilize for 5 minutes, record
or overfire. For natural gas units, operating pressure at manifold pressure and compare to values given in
unit gas connection must be a minimum of 4.5" W.C. table 32. If values are different, adjust to table 32.
(1.12kPa). For L.P. gas units, operating pressure at unit
gas connection must be a minimum of 11.0" W.C.
IMPORTANT
(2.74kPa). For both natural and L.P. gas units, operating For safety, shut unit off and remove manometer as
soon as an accurate reading has been obtained. Take
pressure must not exceed 13" W.C. (3.23 kPa). care to replace pressure tap plug.
On multiple unit installations, each unit should be checked
separately, with and without the other units operating. Sup- NOTE−During this test procedure, the unit will be overfir-
ply pressure minimum and maximum must be the same as ing:
listed in previous paragraph. D Operate unit only long enough to obtain accurate read-
ing to prevent overheating heat exchanger.
E−Check Manifold Pressure D Attempts to clock gas valve during this procedure will
Manifold Operating Pressure is the manifold pressure mea- be inaccurate. Measure gas flow rate only during nor-
sured during normal operation (sensing burner box pressure). mal unit operation.
Manifold Absolute Pressure is manifold pressure measured 6 − When test is complete remove obstruction from hose
when the gas valve regulator is operating at factory preset lev- and return hose to gas valve barb.
el (sensing atmospheric pressure). F− Proper Gas Flow
After line pressure has been checked and adjusted, check Furnace should operate at least 5 minutes before check-
ing gas flow. Determine time in seconds for two revolu-
manifold absolute pressure. Move pressure gauge to outlet
tions of gas through the meter. (Two revolutions assures a
pressure tap located on unit gas valve (GV1). Checks of
more accurate time.) Divide by two and compare to time
manifold absolute pressure are made as verification of proper in table 33 below. Adjust manifold on gas valve to match
regulator adjustment. time needed.
Manifold operating pressure for the GHR32 can be mea- NOTE−To obtain accurate reading, shutoff all other gas
sured at any time the gas valve is open and is supplying appliances connected to meter.
Page 49
TABLE 33 V−TYPICAL OPERATING CHARACTERISTICS
GAS METER CLOCKING CHART
A−Blower Operation and Adjustment
Seconds for One Revolution
NOTE− The following is a generalized procedure and
GHR32 Natural LP does not apply to all thermostat controls.
Unit 1 cu ft 2 cu ft 1 cu ft 2 cu ft
1 − Blower operation is dependent on thermostat con-
Dial Dial Dial DIAL
trol system.
−50 72 144 180 360
2 − Generally, blower operation is set at thermostat sub-
−75 48 96 120 240
base fan switch. With fan switch in ON position, blower
−100 36 72 90 180 operates continuously. With fan switch in AUTO position,
−120 30 60 75 150 blower cycles with demand.
Natural−1000 btu/cu ft LP−2500 btu/cu ft 3 − In all cases, blower and entire unit will be off when the
G−Flame Signal system switch is in OFF position.
A microamp DC meter is needed to check the flame signal on B−Temperature Rise
the SureLight control. Use a flame signal transducer (part Temperature rise for GHR32 units depends on unit input, blow-
number 78H5401) available from Lennox to measure the er speed, blower horsepower and static pressure as marked
flame signal, if meter used will not read microamp signal. on the unit rating plate. The blower speed must be set for unit
Flame (microamp) signal is an electrical current which operation within the range of AIR TEMP. RISE °F" listed on
passes from the ignition control through the sensor elec- the unit rating plate.
trode during unit operation. Current passes from the sen- To Measure Temperature Rise:
sor through the flame to ground to complete a safety circuit. 1 − Place plenum thermometers in the supply and return air
To Measure Flame Signal: plenums. Locate supply air thermometer in the first hori-
1 − Set the volt meter to the DC voltage scale. Insert trans- zontal run of the plenum where it will not pick up radiant
ducer into the VDC and common inputs. Observe cor- heat from the heat exchanger.
rect polarities. Failure to do so results in negative (−) 2 − Set thermostat to highest setting.
values. 3 − After plenum thermometers have reached their high-
2 − Turn off supply voltage to control. est and steadiest readings, subtract the two readings.
3 − Disconnect flame sensor lead from terminal of ignition The difference should be in the range listed on the unit
control. rating plate. If the temperature is too low, decrease
4 − Connect (+) lead of transducer to ignition control sen- blower speed. If temperature is too high, first check the
sor connection. firing rate. Provided the firing rate is acceptable, increase
5 − Connect (−) lead of the transducer to sensor wire. blower speed to reduce temperature. To change blower
6 − Turn supply voltage on and close thermostat contacts speed taps see the Blower Speed Taps section in this
to cycle system. manual.
7 − When unit lights, read voltage on meter display. Re-
member 1 DC volt = 1 DC microamp.
TABLE 34
FLAME SIGNAL MICROAMPS
Boards Normal u0.23
18M34
46M99 Low 0.17 to 0.22
18M99
49M59 Drop Out 0.16
Boards Normal u0.61
63K89
24L85 Low 0.21 to 0.60
56L83
97L48 Drop Out 0.20
H− Variable Speed Motor

To check out the VSM blower and blower control board, begin
with the ICM2 motor and follow the procedures outlined in
section IX−TROUBLESHOOTING. The ICM2 consists of a
control module and motor. The control module can be re-
placed separately form the the motor if necessary. However,
if the motor fails the motor/control module assembly will have
to be replaced.
Page 50
C−External Static Pressure D−Blower Speed Taps GHR32Q Motors
1 − Measure tap locations as shown in figure 49. Blower speed tap changes are made on the SureLight con-
2 − Punch a 1/4" diameter hole in STATIC PRESSURE trol board. See figure 9. Unused taps must be secured on
supply and return air ple- TEST dummy terminals "PARK M1" and or "PARK M2" on the
MANOMETER SureLight board. The heating tap is connected to the "ACB
nums. Insert manometer
hose flush with inside edge of HEAT " terminal and the cooling tap is connected to the
hole or insulation. Seal "ACB COOL" terminal. The continuous blower tap is con-
around the hose with perma- nected to the "ACB LOW" terminal.
gum. Connect the zero end of To change existing heat tap, turn off power then switch out
the manometer to the dis- FIGURE 49 speed tap on "ACB HEAT" with tap connected to "PARK
charge (supply) side of the system. On ducted systems,
M1" or "PARK M2". See wiring diasgrams for blower motor
connect the other end of manometer to the return duct
tap colors for each speed.
as above. For systems with non−ducted returns, leave
the other end of the manometer open to the atmo-
sphere.
3 − With only the blower motor running and the evapo-
rator coil dry, observe the manometer reading. Ad-
just blower motor speed to deliver the air desired ac-
cording to the job requirements.
4 − Pressure drop must not exceed 0.5" W.C.
5 − Seal around the hole when the check is complete.
GHR32 BLOWER REMOVAL
To Remove Blower: J96/P96

J69/P69
1. Turn off line voltage power. Unplug the following
jack/plugs: J96/P96 power interface, J135/P135
secondary limit, J58/P58 control, J98/P98 CAB. J98/P98 J135/P135
2. Remove screws (2) and remove control box cover.
Disconnect thermostat wiring connections by re-
moving low voltage terminal strip. Disconnect spark 4 2
wire and grommet. 3
3. Loosen screws (2) and remove control box from unit.
Holes are slotted so screws do not need to be re-
moved.
4. Remove bolts (2) and remove blower from unit.
FIGURE 50
Page 51
VI−MAINTENANCE Heat Exchanger
1 − Turn off electrical and gas power supplies to furnace.
Retainers for factory supplied return air filter are shown in
figure 51. 2 − Remove upper and lower furnace access panels.
3 − Remove 3/8" rubber cap from condensate drain plug
BACK FILTER CLIP
and drain. Replace cap after draining.
CABINET
WRAPPER 4 − Disconnect and remove intake pipe from air intake fit-
ting.
5 − Mark all gas valve wires and disconnect them from
valve.
6 − Remove gas supply line connected to gas valve.
Disconnect gas valve sensing hose from side of
burner box. Remove burner box cover by removing six
FILTER (four on some units) securing screws. Remove gas valve/
manifold assembly.
FILTER CLIP
7 − Detach burner box from vestibule panel by removing four
Press up on side filter clip to release filter securing screws. Take care to avoid damaging the glass
(One on each side of cabinet)
fiber gasket.
8 − Mark and disconnect spark and sensor electric wires
CABINET from the ignitor and flame sensor.
SIDE FILTER WRAPPER
CLIP DETAIL 9 − Disconnect wires from flame roll−out switch. Remove
wires from patch plates. Remove side plates on burner
box holding sensor and spark electrode. Set burner burn-
FILTER
er box assembly aside.
NOTE− If burner cleaning is needed, do so at this time.
Refer to burner cleaning procedure.
FILTER
CLIP 10− Remove flexible exhaust tee by loosening three
clamps.
Press up on side filter clip to release filter
(One on each side of cabinet) 11− Disconnect drain line attached to condensate trap. Re-
FIGURE 51 move screws that secure both condensate collars to ei-
ther side of the unit and remove collars. It may be neces-
A−Filters sary to cut the pipe to allow for removal of the condensate
At the beginning of each heating season, the system trap. Remove drain tubes from cold end header collector
should be checked as follows: box.
12− Disconnect condensate drain tubing from exhaust
1 − Filters should be inspected monthly and must be
pipe. Remove screws that secure both flue collars
cleaned or replaced when dirty to ensure proper fur- into place. Remove flue collars. It may be neces-
nace operation. sary to cut the exiting exhaust pipe to allow for re-
2 − Reusable foam filters used with the GHR32 can be moval of the fittings.
washed with water and mild detergent. When dry, they 13− Disconnect 2−pin plug from combustion air blower.
should be sprayed with filter handicoater prior to rein- Remove combustion air blower from bracket by re-
moving four securing screws. Remove ground wire from
stallation. Filter handicoater is RP Products coating
bundle.
no. 418 and is available as Lennox part no. P-8-5069.
14− Remove combustion air blower bracket by removing two
3 − If replacement is necessary, order Lennox part no. 31J81 screws from collector box and two screws from ves-
for 14 X 25 inch (356 X 635mm) filter for GHR32-50 and tibule panel.
-75 units and P-8-7831 for 20 X 25 inch (508 X 635mm) 15− Disconnect combustion air pressure and condensate
filter for GHR32-100 and -120 units. sensing hoses from cold end header collector box. Re-
move pressure hose from two blank stems on cold end
B−Cleaning Heat Exchanger and Burners header collector box.
NOTE−Use papers or protective covering in front of fur- 16− Mark and remove wires from pressure switch. Re-
nace while cleaning furnace. move pressure switch/bracket assembly. Keep
Cleaning the heat exchanger is not recommended; but, if it be- hoses attached to pressure switch. Remove pres-
comes necessary, follow the procedures outlined below and sure switch installation screws from both sides of
refer to figure 1 for parts arrangement. Pay close attention to the unit.
wire routing and plumbing connections.
If at all possible, the unit should be removed and placed 17− Disconnect 9−pin and 3− pin plugs at blower deck. Re-
on its back. Tools needed are: slotted screwdriver, extra move both plugs from the heat exchanger side of the
long 1/4" nut driver, extra long 5/16" nut driver, and duck- blower deck.
bill pliers. 18− Remove the primary limit from vestibule panel.
Page 52
19− Remove two (2) screws from the front cabinet flange at 30− Connect combustion air pressure and condensate
the blower deck. Remove front screws from cabinet at sensing hoses from pressure switch to cold end
blower deck on left and right sides. Cabinet sides must header collector box. See figure 31to confirm hose
be slightly spread apart to clear heat exchanger pas- location.
sage. 31− Re−install the combustion air bracket.
NOTE−To protect insulation in horizontal applications,
32− Re−install the combustion air blower to bracket. Re-
slide a piece of sheet metal between the coil section of connect the 2−pin plug to the wire harness.
the heat exchanger and the cabinet when removing
and replacing heat exchanger. Remove indoor 33− Replace flue collars with securing screws to either side of
the unit. Reconnect exhaust piping and exhaust
blower for horizontal installations. Remove sheet
drain tubing.
metal when complete.
34− Replace condensate collars with securing screws to
20− Remove screws along vestibule sides and bottom either side of the unit. Reconnect drain line to conden-
which secure vestibule panel and heat exchanger as- sate trap. Reconnect drain tubing from cold end head-
sembly to cabinet. er collector box. Reconnect condensate drain tubing
from exhaust pipe.
21− With a pair of duck bills, carefully bend bottom flange
35− Replace flexible exhaust tee to combustion air
straight. Use caution not to damage the cabinet. Re-
blower and exhaust pipes and secure with three
move heat exchanger.
clamps.
22− Back wash heat exchanger with soapy water solu- 36− Align burner box gasket to securing holes closest to
tion or steam. If steam is used it must be below the end of the unit. Use a small piece of tape to secure
275_F (135_C). gasket to vest panel. Make sure glass fiber gasket has
23− Thoroughly rinse and drain the heat exchanger. Soap not been damaged so it will provide a continuous seal
solution can be corrosive so take care that entire as- between the burner box and the vestibule panel.
sembly is completely rinsed. 37− Move burner box assembly to vestibule area.
24− Re−install heat exchanger into cabinet (blower deck end 38− Reconnect flame roll−out switch wires. Re−install
first) making sure that the clamshells of the heat ex- patch plates to side of burner box. Connect wires to
changer assembly are resting on the supports at patch plates.
the rear of the cabinet. This can be viewed by re- 39− Reconnect sensor and spark electrode or SureLight
moving the indoor blower and examining through ignitor wires through provided openings in the burner
the blower opening. plate.
25− Re−secure the supporting screws along the vestibule 40− Replace four screws to secure reassembled burner
sides and bottom to the cabinet. Carefully bend bot- box assembly to vestibule panel. Make sure burn-
tom flange back to a 90 degree angle with a pair of ers line up in center of burner ports.
duck bills. Once again, use caution not to damage the
41− Re−install gas valve manifold assembly. Replace
cabinet.
burner box cover. Re−install gas supply line to gas
26− Re−install cabinet screws on sides and front flange at valve. Attach gas valve pressure sensing hose to
blower deck. burner box.
27− Re−install primary limit to vestibule panel. 42− Reconnect gas valve wires to gas valve.
43− Re−install intake vent pipe to rubber connector on in-
28− Re−install 9−pin plug to blower deck and connect it to the
take fitting with hose clamp.
9−pin plug from below the blower deck. Re−install 3−pin
plug to blower deck and connect it to the 3−pin plug from 44− Replace both upper and lower access panels.
below the blower deck. 45− Refer to instruction on verifying gas and electrical con-
29− Re−install pressure switch/bracket assembly and re- nections when re−establishing supply.
place pressure switch screws on both sides of unit 46− Following lighting instructions, light and run unit for 5
from installed pressure switch. Reconnect wires to minutes to ensure heat exchanger is clean, dry and
pressure switch. operating safely.
Page 53
Cleaning the Burner Assembly 18− Re−install gas valve/manifold assembly. Re−install
1 − Turn off electrical and gas power supplies to furnace. burner box cover. Reconnect gas valve sensing hose
to side of burner box. Re−install gas supply line to gas
2 − Remove upper and lower furnace access panels. valve.
3 − Disconnect and remove intake pipe from air intake fit- 19− Reconnect gas valve wires to gas valve.
ting.
20− Replace both upper and lower access panels.
4 − Mark all gas valve wires and disconnect them from
valve. 21− Refer to instruction on verifying gas and electrical con-
nections when re−establishing supply.
5 − Remove gas supply line connected to gas valve.
22− Following lighting instructions, light and run unit for 5
Disconnect gas valve sensing hose from valve. Re-
minutes to ensure heat exchanger is clean, dry and
move burner box cover (4 to 6 screws). Remove gas
operating safely.
valve/manifold assembly.
6 − Loosen hose clamp holding the air intake pipe to the C−Supply Air Blower
no−hub connector on the top of the burner box. Re-
move pipe from no−hub connector and set aside. 1 − Check and clean blower wheel.
7 − Mark and disconnect spark or SureLight ignitor and 2 − Motors are prelubricated for extended life; no further lu-
sensor electrical wires from the ignitor and flame sen- brication is required.
sor.
8 − Detach burner box from vestibule panel by remov- D−Electrical
ing four securing screws. Take care to avoid dam- 1 − Check all wiring for loose connections.
aging the glass fiber gasket.
2 − Check circuit breaker located in unit control box.
9 − On GHR32−50 and −75 units, remove air intake fitting from
3 − Check for correct voltage at unit (unit operating).
burner box top.
4 − Check amp-draw on blower motor.
10 − Remove burner box top from burner box assembly.
Motor Nameplate_________Actual_________
11− Using 1/4" nut driver, remove two screws holding
5 − Check to see that heat (if applicable) is operating.
burners in place. Slide burner assembly out of burn-
er box.
E−Intake and Exhaust Lines
12− Clean burner by running a vacuum with a soft brush at-
tachment over face of burners. Visually inspect inside Check intake and exhaust lines and all connections for
of burners and crossovers for any blockage caused by tightness and make sure there is no blockage. Also check
foreign matter. Remove any blockage. condensate line for free flow during operation.
13− Re−install burner assembly so that protruding side (not
cavity side) of metal buttons are toward the burner box F−Insulation
top (intake side). Outdoor piping insulation should be inspected yearly for deteri-
14− Replace top and air intake piece to burner box. oration. If necessary, replace with same materials.
15− Reconnect sensor and spark electrode or SureLight

G−Winterizing and Condensate Trap Care
ignitor wires.
If the unit is to be shut down for an extended period of time
16− Align burner box gasket to securing holes closest to
and will be exposed to sub-freezing temperatures, the unit
the end of the unit. Use a small piece of tape to secure
gasket to vest panel. Make sure glass fiber gasket has should be winterized by draining water from the conden-
not been damaged so it will provide a continuous seal sate trap.
between the burner box and the vestibule panel. To drain condensate trap remove the 3/8" cap located on
17− Replace four screws to secure reassembled burner the bottom corner of the condensate trap (see figure 46).
box assembly to vestibule panel. Make sure burn- Periodically drain condensate trap to insure proper drain-
ers line up in center of burner ports. age and check for blockage.
Page 54
VII−WIRING DIAGRAM AND SEQUENCE OF OPERATION
GHR32Q −1 UNIT DIAGRAM
Page 55
GHR32Q −3 UNIT DIAGRAM
Page 56
Sequence of Operation GHR32Q −1, −3 Units Two−stage Mode, Single−stage Thermostat
1 − SureLight control energizes combustion air inducer
Ignitor operation will vary between SureLight boards. B6 on low speed. Combustion air inducer runs until
Board 56L83 will energize ignitor for the first second of the combustion air proving switch S18 closes (switch will
4 second ignition trial. Board 97L48 will energize ignitor
close within 2−1/2 minutes or control goes into Watch-
during the entire ignition trial until flame is sensed.
guard−Prove Switch mode). A 15−second pre−purge
1 − When there is a call for heat, W1 of the thermostat en- follows once S18 closes.
ergizes W of the furnace control with 24VAC. 2 − SureLight control energizes ignitor. A 20−second
2 − SureLight control runs self−check for S10 primary limit warm−up period begins.
switch normally closed contacts and S18 combustion 3 − Gas valve is energized on first stage. Gas valve opens
air prove switch normally open contacts. Follow steps for a 4−second trial for ignition. Signal is sent from con-
4 through 8 per respective thermostat. trol module to two−stage control board to begin W2
(second−stage) ON delay.
Single−stage Mode, Single−stage Thermostat 4 − Flame is sensed, gas valve remains open for the heat
3− SureLight control energizes combustion air inducer call.
B6 on high speed. Combustion air inducer runs until 5 − After 45−second delay, indoor blower B3 is energized
S18 prove switch closes (switch will close within 2−1/2 on low speed.
minutes or control goes into Watchguard−Prove 6 − Second stage time on delay complete (8, 12, or 15
Switch mode). A 15−second pre−purge follows after minutes). Combustion air inducer B6 switches to high
S18 closes. speed, indoor blower B3 switches to heating speed
4− SureLight control energizes ignitor. A 20−second and gas valve opens on high heat (second stage.)
warm−up period begins.
Two−stage Mode, Two−stage Thermostat
5− Gas valve is energized on first stage heat (low). Gas 1 − SureLight control energizes combustion air inducer
valve opens for a 4−second trial for ignition. B6 on low speed. Combustion air inducer runs until
6− Flame is sensed, After 8 seconds from when gas valve combustion air inducer switch S18 closes. Switch will
opens, valve energizes on second stage (high heat). close within 2−1/2 minutes or control goes into Watch-
7− After 45−second delay, indoor blower B3 is energized guard−Proving Switch mode). A 15−second pre−purge
on heating speed. follows once S18 closes.
2 − SureLight control energizes ignitor. A 20−second
3 − Gas valve is energized on first stage only. Gas valve
opens for a 4−second trial for ignition.
4 − Flame is sensed, gas valve remains open for the heat
call.
5 − After 45−second delay, indoor blower B3 is energized
on low speed.
6 − Call for second stage heat comes from indoor thermo-
stat (W2).
Page 57
GHR32Q −5 & −6 UNIT DIAGRAM
Page 58
Sequence of Operation. GHR32Q with Single−Stage Thermostat, Two Stage Heat. Jumper
E20 set at SINGLE"
SureLight Two Stage Control
1− SureLight control energizes combustion air inducer B6
Sequence depends on type thermostat used. Units are on low heat speed. Combustion air inducer runs until
applicable for single stage or two stage thermostats. S102 prove switch contacts close (switch must close
Both type thermostats are described below. Thermo- within 2 1/2 minutes or control goes into Watchguard
stat jumper E20 dictates which mode unit will operate Pressure Switch mode. A 15 second pre−purge follows
in. See flow chart for more sequence detail. once S102 closes.
SureLight Control Self Check 2− SureLight control begins 20 second ignitor warm up
When there is a call for heat, the SureLight integrated con- period.
trol runs a self check. The control checks for S10 primary 3− Gas valve opens on first stage for a 4 second trial for
limit, S21 secondary limit (s) and S47 rollout switch nor- ignition. Ignitor stays energized during the trial or until
mally closed contacts. The control also checks for S102 flame sensed.
prove switch normally open contacts. Once self check is 4− Flame is sensed, gas valve remains on first stage heat,
complete and all safety switches are operational, heat call ignitor de−energizes.
can continue. 5− After 45 second delay, indoor blower B3 is energized
Two−Stage Thermostat, Two Stage Heat. Jumper E20 on low heat speed.
set at TWO". 6− A 10 minute (factory set) or 15 minute (field set) second
1− SureLight control energizes combustion air inducer B6 stage heat delay period begins.
on low heat speed. Combustion air inducer runs until 7− The combustion air inducer ramps up to high heat
S102 closes (switch must close within 2 1/2 minutes or speed.
control goes into Watchguard Pressure Switch mode. 8− B3 indoor blower ramps up to high heat speed.
A 15 second pre−purge follows once S102 closes.
2− SureLight control begins 20 second ignitor warm up
period.
3− Gas valve opens on first stage for a 4 second trial for
ignition. Ignitor stays energized during the trial or until
flame sensed.
4− Flame is sensed, gas valve remains on first stage heat,
ignitor de−energizes.
5− After 45 second delay, indoor blower B3 is energized
on low heat speed.
The furnace will stay in this mode until first stage de-
mand is satisfied OR a second stage heat demand is
initiated.
6− Second stage heat demand initiated. A 30 second sec-
ond stage recognition period begins.
7− The combustion air inducer ramps up to high heat
speed.
8− B3 indoor blower ramps up to high heat speed.
Page 59
GHR32V −1 UNIT DIAGRAM
Page 60
Page 61
Page 62
Sequence of Operation GHR32V −1 / −4 Units Two−stage Mode, Single−stage Thermostat
1 − SureLight control energizes combustion air inducer
Ignitor operation will vary between SureLight boards. B6 on low speed. Combustion air inducer runs until
Board 56L83 will energize ignitor for the first second of the combustion air proving switch S18 closes (switch will
4 second ignition trial. Board 97L48 will energize ignitor
close within 2−1/2 minutes or control goes into Watch-
during the entire ignition trial until flame is sensed.
guard−Prove Switch mode). A 15−second pre−purge
1 − When there is a call for heat, W1 of the thermostat en- follows once S18 closes.
ergizes W of the furnace control with 24VAC. 2 − SureLight control energizes ignitor. A 20−second
2 − SureLight control runs self−check for S10 primary limit warm−up period begins.
switch normally closed contacts and S18 combustion 3 − Gas valve is energized on first stage. Gas valve opens
air prove switch normally open contacts. Follow steps for a 4−second trial for ignition. Signal is sent from con-
4 through 8 per respective thermostat. trol module to two−stage control board to begin W2
(second−stage) ON delay.
Single−stage Mode, Single−stage Thermostat 4 − Flame is sensed, gas valve remains open for the heat
3− SureLight control energizes combustion air inducer call.
B6 on high speed. Combustion air inducer runs until 5 − After 45−second delay, indoor blower B3 is energized
S18 prove switch closes (switch will close within 2−1/2 on low speed.
minutes or control goes into Watchguard−Prove 6 − Second stage time on delay complete (8, 12, or 15
Switch mode). A 15−second pre−purge follows after minutes). Combustion air inducer B6 switches to high
S18 closes. speed, indoor blower B3 switches to heating speed
4− SureLight control energizes ignitor. A 20−second and gas valve opens on high heat (second stage.)
Two−stage Mode, Two−stage Thermostat
5− Gas valve is energized on first stage heat (low). Gas 1 − SureLight control energizes combustion air inducer
valve opens for a 4−second trial for ignition. B6 on low speed. Combustion air inducer runs until
6− Flame is sensed, After 8 seconds from when gas valve combustion air inducer switch S18 closes. Switch will
opens, valve energizes on second stage (high heat). close within 2−1/2 minutes or control goes into Watch-
7− After 45−second delay, indoor blower B3 is energized guard−Proving Switch mode). A 15−second pre−purge
on heating speed. follows once S18 closes.
2 − SureLight control energizes ignitor. A 20−second
3 − Gas valve is energized on first stage only. Gas valve
opens for a 4−second trial for ignition.
4 − Flame is sensed, gas valve remains open for the heat
call.
5 − After 45−second delay, indoor blower B3 is energized
on low speed.
6 − Call for second stage heat comes from indoor thermo-
stat (W2).
Page 63
GHR32V −5 & −6 UNIT DIAGRAM
Page 64
Sequence of Operation GHR32V with Single−Stage Thermostat, Two Stage Heat. Jumper
E20 set at SINGLE"
SureLight Two Stage Variable Speed Control
1− SureLight control energizes combustion air inducer B6
Sequence depends on type thermostat used. Units are on low heat speed. Combustion air inducer runs until
applicable for single stage or two stage thermostats. S102 prove switch contacts close (switch must close
Both type thermostats are described below. Thermo- within 2 1/2 minutes or control goes into Watchguard
stat jumper E20 dictates which mode unit will operate Pressure Switch mode. A 15 second pre−purge follows
in. See flow chart for more sequence detail. once S102 closes.
SureLight Control Self Check 2− SureLight control begins 20 second ignitor warm up
When there is a call for heat, the SureLight integrated con- period.
trol runs a self check. The control checks for S10 primary 3− Gas valve opens on first stage for a 4 second trial for
limit, S21 secondary limit (s) and S47 rollout switch nor- ignition. Ignitor stays energized during the trial or until
mally closed contacts. The control also checks for S102 flame sensed.
prove switch normally open contacts. Once self check is 4− Flame is sensed, gas valve remains on first stage heat,
complete and all safety switches are operational, heat call ignitor de−energizes.
can continue. 5− After 45 second delay, indoor blower B3 is energized
Two−Stage Thermostat, Two Stage Heat. Jumper E20 on low heat speed.
set at TWO". 6− A 10 minute (factory set) or 15 minute (field set) second
1− SureLight control energizes combustion air inducer B6 stage heat delay period begins.
on low heat speed. Combustion air inducer runs until 7− The combustion air inducer ramps up to high heat
S102 prove switch contacts close (switch must close speed.
within 2 1/2 minutes or control goes into Watchguard 8− B3 indoor blower ramps up to high heat speed.
Pressure Switch mode. A 15 second pre−purge follows
once S102 closes.
2− SureLight control begins 20 second ignitor warm up
period.
3− Gas valve opens on first stage for a 4 second trial for
ignition. Ignitor stays energized during the trial or until
flame sensed.
4− Flame is sensed, gas valve remains on first stage heat,
ignitor de−energizes.
5− After 45 second delay, indoor blower B3 is energized
on low heat speed.
The furnace will stay in this mode until first stage de-
mand is satified OR a second stage heat demand is
initiated.
6− Second stage heat demand initiated. A 30 second sec-
ond stage recognition period begins.
7− The combustion air inducer ramps up to high heat
speed.
8− B3 indoor blower ramps up to high heat speed.
Page 65
VIII−Sequence of Operation Flow Charts
GHR32Q −1 & −3 GHR32V−1 / −4
HEATING SEQUENCE OF OPERATION

NOTE: LED REFERS TO SURELIGHT CONTROL . LED−DS REFERS TO VSP CONTROL.
NORMAL HEATING MODE ABNORMAL HEATING MODE
GAS VALVE OFF. COMBUSTION AIR INDUCER ON.
POWER ON INDOOR BLOWER ON. LED #1 AND #2
ALTERNATING FAST FLASH. CHECK FOR
BROKEN IGNITOR OR OPEN IGNITOR CIRCUIT.
CONTROL SELF−CHECK OKAY? NO
GAS VALVE OFF. COMBUSTION AIR INDUCER OFF.
INDOOR BLOWER DELAY OFF.
LED #1 ON
LED #2 ON
(RESET CONTROL BY TURNING MAIN POWER OFF.)
COMBUSTION AIR BLOWER ON FOR 1 SECOND.
POLARITY REVERSED.
NO LED #1 −− FAST FLASH
POLARITY OKAY? LED #2 −− SLOW FLASH
YES
LED#1 AND #2
NO IS THERE A YES IS VOLTAGE NO LED #1 AND #2 ALTERNATING FAST FLASH.
ALTERNATING FAST SIGNAL HOLDS UNTIL VOLTAGE RISES
FLASH. SIGNAL PROPER GROUND? ABOVE 75 VOLTS?
ABOVE 75 VOLTS.
HOLDS UNTIL UNIT IS
PROPERLY GROUND. YES
ROLLOUT SWITCH CLOSED? GAS VALVE OFF. COMBUSTION AIR INDUCER OFF.
YES NO INDOOR BLOWER OFF DELAY.
LED #1 −− ON
BURNER OFF? LED #2 −− SLOW FLASH
(CONTINUOUS FLAME CHECK)
YES
NORMAL OPERATION: NO INDOOR BLOWER ON.
LED #1 −− SIMULTANEOUS SLOW FLASH LED #1 −− SLOW FLASH
LED #2 −− SIMULTANEOUS SLOW FLASH LED #2 −− OFF
THERMOSTAT CALLS FOR HEAT:

LED #1 −− FAST FLASH
LED #2 −− FAST FLASH
YES COMBUSTION AIR INDUCER OFF.
NO INDOOR BLOWER ON.
PRIMARY LIMIT SWITCH CLOSED?
LED #1 −− SLOW FLASH
YES LED #2 −− ON
PRESSURE SWITCH CONTACTS OPEN?
(HIGH AND LOW HEAT) GAS VALVE OFF.
YES NO COMBUSTION AIR INDUCER OFF.
INDOOR BLOWER OFF DELAY.
ENERGIZE COMBUSTION AIR BLOWER.
LED #1 OFF
ENERGIZE HTG ACC. TERM.
LED #2 SLOW FLASH
YES (Sequence holds until pressure switch
IS UNIT PROPERLY GROUNDED? closes or thermostat resets control.)
YES NO
IS LINE VOLTAGE ABOVE 75 VOLTS? COMBUSTION AIR INDUCER OFF.
INDOOR BLOWER OFF.
LED #1 −− ALTERNATING FAST FLASHES
TWO−STAGE MODE W2 TIMED MODE SINGLE−STAGE MODE LED #2 −− ALTERNATING FAST FLASHES
CALL FOR 1ST STAGE HEAT SINGLE STAGE T’STAT HIGH HEAT ONLY
COMBUSTION AIR BLOWER COMBUSTION AIR BLOWER

ON LOW SPEED (t 2.5 MINUTES) ON HIGH SPEED (t 2.5 MINUTES)
PRESSURE SWITCH WATCHGUARD
(5 MINUTES)
LOW−HEAT PRESSURE NO HIGH−HEAT PRESSURE NO COMBUSTION AIR INDUCER OFF.
SWITCH CLOSED? SWITCH CLOSED? INDOOR BLOWER OFF.
YES YES LED #1 OFF
LED #2 SLOW FLASH
PREPURGE
15 SECONDS WATCHGUARD 60-MINUTE DELAY
(SIGNAL LIMIT OR IGNITION FAILURE)
GAS VALVE OFF. COMBUSTION AIR
AND INDOOR BLOWER OFF.
CONTINUED ON NEXT PAGE LED #1 AND LED #2
ALTERNATING SLOW FLASHES
Page 66
HEATING SEQUENCE CONTINUED
PREPURGE
15 SECONDS
WATCHGUARD 60-MINUTE DELAY
(SIGNAL LIMIT OR IGNITION FAILURE)
AND INDOOR BLOWER OFF.
LED #1 AND LED #2
IGNITION SEQUENCE BEGINS ALTERNATING SLOW FLASHES
(Ignition trial counter initiated.)
WATCHGUARD −− FLAME FAILURE.
GAS VALVE OFF.
IGNITOR WARM−UP COMBUSTION AIR INDUCER OFF.
(20 SECONDS) INDOOR BLOWER OFF.
LED #1 & LED #2 ALTERNATE FLASH.
TWO−STAGE MODE W2 TIMED MODE SINGLE−STAGE MODE

CALL FOR 1st STAGE HEAT SINGLE STAGE T’STAT HIGH HEAT ONLY YES
NO
MAIN GAS VALVE OPEN CONTROL CHECKS RETRY

MAIN GAS VALVE OPEN
LOW HEAT ONLY LOW HEAT ONLY GAS VALVE OPEN ON LOW HEAT. FOR IGNITION COUNT.
SECOND STAGE WITHIN 8 SEC. VALVE OPENS HIGH HEAT. HAVE FOUR RE-TRIES
TIME ON BEGINS BEEN COMPLETED?
4 SECONDS 8 SECONDS
FLAME RECTIFICATION CURRENT CHECK

(u0.20 microamps)
FLAME PRESENT? NO GAS VALVE

(Response time −− 2 seconds maximum.) DE−ENERGIZED
45 SECOND INDOOR BLOWER DELAY BEGINS. AFTER DELAY ACC. TERMINAL IS

ENERGIZE. Q" MODELS: ACB HEAT SPEEDIS ENERGIZED. V" MODELS: HEAT"
LED−DS2 LIT. BLOWER ON HEAT SPEED.

CALL FOR 1st STAGE HEAT SINGLE STAGE T’STAT HIGH HEAT ONLY YES
LIMIT SWITCH WATCHGUARD MODE.

Q" MODELS: INDOOR BLOWER ON LOW Q" MODELS: INDOOR BLOWER ON GAS VALVE OFF. COMB. AIR
SPEED. V" MODELS: CFM" LED−DS4 HIGH HEATING SPEED. V" INDUCER OFF. INDOOR BLOWER
BLINKS ONCE FOR EVERY 100CFM. MODELS: CFM" LED−DS4 BLINKS OFF AFTER DELAY. LED#1−SLOW
ONCE FOR EVERY 100CFM. FLASH LED#2−ON. IS 60 MINUTE
NO RESET PERIOD COMPLETE?
FLAME PRESENT?
(Continuous flame check)
LOW FLAME SIGNAL
NO LED #1 −− SLOW FLASH
FLAME SIGNAL LED #2 −− FAST FLASH
(u0.61 microamps)
GAS VALVE DE−ENERGIZED.
NO COMBUSTION AIR INDUCER DE−ENERGIZED.
PRIMARY LIMIT SWITCH CLOSED? INDOOR BLOWER ON.
LED #1 − SLOW FLASH; LED #2 − ON.
NO NO
ROLLOUT SWITCH CLOSED? HAS PRIMARY/SECODARY LIMIT YES
CLOSED (RESET) WITHIN 3 MINUTES?
PRESSURE SWITCH CLOSED?

(CONTINUED ON NEXT PAGE)
GAS VALVE DE−ENERGIZED.
COMBUSTION AIR INDUCER DE−ENERGIZED.
CONTINUED ON NEXT PAGE INDOOR BLOWER OFF DELAY (Selected time)
LED #1 −− ON
LED #2 −− SLOW FLASH
Page 67
HEATING SEQUENCE CONTINUED
PREPURGE
NO (See top of previous page.)
PRESSURE SWITCH CLOSED?
YES YES GAS VALVE DE−ENERGIZED.

TWO−STAGE MODE W2 TIMED MODE INDOOR BLOWER DE−ENERGIZED.
CALL FOR 1st STAGE HEAT SINGLE STAGE T’STAT COMBUSTION AIR INDUCER ON FOR 2.5 MINUTES.
CALL FOR 2nd STAGE 2nd STAGE ON DELAY PRESSURE SWITCH

HEAT (HIGH HEAT) ON CONTROL BOARD CLOSED?
FROM THERMOSTAT COMPLETE (8, 12 OR 15 MIN.)
PRESSURE SWITCH WATCHGUARD

Q" MODELS: INDOOR BLOWER SWITCHES TO HEATING
COMBUSTION AIR INDUCER
SPEED. V" MODELS: CFM" LED−DS4 BLINKS ONCE FOR
DE−ENERGIZED.
EVERY 100 CFM.
¦ 2.5
MINUTES 5−MINUTE DELAY
COMBUSTION AIR INDUCER SWITCHES TO
HIGH SPEED?
COMBUSTION AIR
HIGH HEAT PRESSURE SWITCH CLOSED? BLOWER ON.
YES
HIGH HEAT GAS VALVE OPEN? (8 SEC. DELAY) NO
YES

CALL FOR 1st STAGE HEAT SINGLE STAGE T’STAT HIGH HEAT ONLY
CONTROL CHECKS: FLAME PRESENCE, CLOSED PRIMARY

LIMIT, CLOSED PRESSURE SWITCHES, CONTINUOUSLY DIAGNOSTIC CODES
CLOSED ROLLOUT SWITCH (during heating cycle). LED #1 LED #2 DESCRIPTION
SEE PREVIOUS SEQUENCES FOR FAILURE MODES.
SLOW FLASH ON Primary or secondary limit open
ON SLOW FLASH Rollout switch open

SLOW FLASH OFF Flame sensed without gas valve energized
DEMAND FOR HEAT SATISFIED.
OFF SLOW FLASH Pressure switch open
THERMOSTAT OPENS.
SLOW FLASH SLOW FLASH Power on
FAST FLASH FAST FLASH Heating demand

GAS VALVE DE−ENERGIZED. FAST FLASH SLOW FLASH Polarity reversed
SLOW FLASH FAST FLASH Low flame signal
ON ON Circuit board failure

COMBUSTION AIR INDUCER POST−PURGE 5
ALTERNATING SLOW FLASH Watchguard −− burners failed to ignite
SECONDS. HTG ACC. TERM. DE−ENERGIZED
Watchguard −− low voltage, below 75V or
ALTERNATING FAST FLASH improper main ground.
INDOOR BLOWER AND ACC TERMINAL OFF AFTER SELECTED

TIME OFF DELAY.
Page 68
COOLING SEQUENCE OF OPERATION
NORMAL COOLING MODE ABNORMAL COOLING MODE
POWER ON
IGNITION CONTROL MAIN POWER ON.

CONTROL SELF DIAGNOSTIC CHECK. NO INDOOR BLOWER OFF WITH NORMAL DELAY.
IS CONTROL OPERATING NORMALLY? SIGNAL CIRCUIT BOARD FAILURE AT LED.
INTERRUPT MAIN POWER TO RESET CONTROL.
YES
TURN INDUCER ON FOR 1 SECOND.
YES
IS POLARITY REVERSED? SIGNAL POLARITY REVERSED AT LED.
NO
SIGNAL IMPROPER
GROUND AT LED. NO NO
SIGNAL HOLDS IS THERE YES IS VOLTAGE LOW VOLTAGE SIGNAL AT LED HOLDS
UNTIL UNIT IS PROPER GROUND? ABOVE 75 VOLTS? UNTIL VOLTAGE RISES ABOVE 75 VOLTS.
PROPERLY
GROUNDED.
NO GAS VALVE OFF. COMBUSTION AIR INDUCER OFF.

ROLLOUT SWITCH MONITORED CONTINUOUSLY. INDOOR BLOWER OFF WITH NORMAL DELAY.
IS ROLLOUT SWITCH CLOSED? SIGNAL CIRCUIT BOARD FAILURE AT LED.
SEQUENCE HOLDS UNTIL ROLLOUT SWITCH CLOSES.
YES
CHECK FOR MAIN BURNER FLAME SENSE. INDOOR BLOWER OFF WITH NORMAL DELAY.
IS MAIN BURNER FLAME OFF? SIGNAL CIRCUIT BOARD FAILURE AT LED.
SEQUENCE HOLDS UNTIL FLAME IS NOT SENSED.
LED: SLOW FLASH RATE REMAINS UNCHANGED

THROUGHOUT COOLING CYCLE.
THERMOSTAT CALLS FOR COOLING.
COMPRESSOR CONTACTOR AND INDOOR

BLOWER ENERGIZED WITH 0-SECOND DELAY
Q" MODELS: ACB COOL AND ACC TERMINAL
ENERGIZED. V" MODELS: HI/LO" LED−DS1 IS
LIT. CFM" LED−DS4 BLINKS ONCE FOR EVERY
100CFM.
THERMOSTAT OPENS.
COMPRESSOR OFF.
INDOOR BLOWER AND ACC TERMINAL OFF

WITH 0−SECOND DELAY.
Page 69
CONTINUOUS LOW SPEED FAN SEQUENCE OF OPERATION
LED: SLOW FLASH RATE REMAINS

UNCHANGED THROUGHOUT SEQUENCE.
MANUAL FAN SELECTION MADE AT THERMOSTAT. CONTROL

(G)ENERGIZING ACC TERMINAL. Q" MODELS: ACB LOW
SPEED ENERGIZED. V" MODELS: ON/OFF" LED−DS3 LIT.
INDOOR BLOWER ENERGIZED ON LOW SPEED.
HTG ACC TERMINAL ENERGIZES

THERMOSTAT CALLS FOR HEAT (W). WITH COMB. AIR INDUCER.
NO YES
45 SECOND INDOOR BLOWER DELAY BEGINS. AFTER DELAY − Q"

MODELS: ACB HEAT SPEED ENERGIZED. V" MODELS: HEAT"
THERMOSTAT CALLS FOR COOLING.
LED−DS2 LIT. BLOWER ON HEAT SPEED.
YES
Q" MODELS: INDOOR BLOWER SWITCHED TO ACB

COOL SPEED. V" MODELS: HI/LO LED−DS1 LIT.
THERMOSTAT OPENS.
THERMOSTAT OPENS. INDOOR BLOWER TIME OFF DELAY BEGINS. HTG ACC TERMINAL
DE−ENERGIZED WITH COMBUSTION AIR INDUCER. ACC TERMINAL
REMAINS ENERGIZED. AFTER DELAY − "Q" MODELS: ACB HEAT
SPEED DE−ENERGIZED. V" MODELS: INDOOR BLOWER HEAT
SPEED DE−ENERGIZED.
(blower remains energized during continuous fan mode)
Q" MODELS − INDOOR BLOWER SWITCHES TO ACB

LOW SPEED. V" MODELS − ON/OFF" LED−DS3 LIT.
INDOOR BLOWER ON LOW SPEED.
Page 70
GHR32Q with Two Stage Control and GHR32V with Two Stage Variable Speed Control

NORMAL AND ABNORMAL HEATING MODE
GAS VALVE OFF. COMBUSTION AIR INDUCER
POWER ON OFF. INDOOR BLOWER OFF. CHECK FOR
BROKEN IGNITOR OR OPEN IGNITER CIRCUIT.
DS 1 AND DS 2 ALTERNATING FAST FLASH.
CONTROL SELF−CHECK OKAY? NO
INDOOR BLOWER OFF. (RESET CONTROL BY
TURNING MAIN POWER OFF.) DS1 ON, DS2 ON
NO POLARITY REVERSED.
POLARITY OKAY? DS 1 −− FAST FLASH
YES DS 2 −− SLOW FLASH
IS THERE A NO SIGNAL HOLDS UNTIL UNIT IS PROPERLY GROUNDED.

PROPER GROUND? DS1 AND DS2 ALTERNATING FAST FLASH.
YES
IS VOLTAGE NO SIGNAL HOLDS UNTIL VOLTAGE RISES ABOVE 75 VOLTS.
ABOVE 75 VOLTS? DS1 AND DS2 ALTERNATING FAST FLASH.
YES
BURNER OFF? NO INDOOR BLOWER ON HEATING SPEED.
(CONTINUOUS FLAME CHECK) DS1 SLOW FLASH, DS2 OFF,
YES ON/OFF LED OFF
A
NORMAL OPERATION:
DS 1 −− SIMULTANEOUS SLOW FLASH COMBUSTION AIR INDUCER OFF.
DS 2 −− SIMULTANEOUS SLOW FLASH INDOOR BLOWER ON. HAS PRIMARY LIMIT
RESET WITHIN 3 MINUTES?
DS1 SLOW FLASH, DS2 ON, YES
B ON/OFF LED ON, HEAT LED ON.
NO THERMOSTAT CALLS FOR HEAT: NO
DS 1 −− SIMULTANEOUS FAST FLASH
DS 2 −− SIMULTANEOUS FAST FLASH NO 60−MINUTE LIMIT WATCHGUARD MODE.
GAS VALVE OFF, COMBUSTION AIR INDUCER
YES OFF, INDOOR BLOWER OFF WITH DELAY.
PRIMARY LIMIT DS1 AND DS2 ALTERNATING SLOW FLASH,
SWITCH CLOSED? ON/OFF LED OFF, HEAT LED ON.
YES
ROLLOUT SWITCH CLOSED? HAS MANUAL ROLLOUT SWITCH(ES) BEEN NO
RESET (CLOSED) WITHIN 3 MINUTES?
YES DS1 SLOW FLASH, DS2 ON, YES
ON/OFF LED ON, HEAT LED ON.
PRESSURE SWITCH CONTACTS OPEN? NO
YES GAS VALVE OFF. COMBUSTION AIR INDUCER OFF.

INDOOR BLOWER OFF. CONTROL REMAINS UNTIL
TWO−STAGE OR SINGLE−STAGE THERMOSTAT
PRESSURE SWITCH IS DETECTED OPEN.
CALL FOR HEAT
DS1 OFF, DS2 SLOW FLASH,
ON/OFF LED OFF, HEAT LED OFF.
COMBUSTION AIR INDUCER ON LOW SPEED.

DS1 AND DS2 SIMULTANEOUS FAST FLASH
CONTINUED ON NEXT PAGE
Page 71
CONTINUED THERMOSTAT CALLS FOR HEAT
(Refer to box A on previous page)
PRESSURE SWITCH CLOSED WITHIN NO GAS VALVE OFF. COMBUSTION AIR INDUCER
2.5 MINUTES? OFF. INDOOR BLOWER OFF. UNIT WILL RETRY
AFTER 5−MINUTE WAIT PERIOD.
YES DS1 OFF, DS2 SLOW FLASH,
15−SECOND COMBUSTION AIR INDUCER
PRE−PURGE INITIATED BY CLOSED PRESSURE
SWITCH (or 15 SECOND INTER−PURGE PERIOD.)
DS1 AND DS2 SIMULTANEOUS FAST FLASH.
IGNITOR WARM−UP (20 SECONDS)

NO COMBUSTION AIR INDUCER OFF, IGNITER OFF.

IS VOLTAGE ABOVE 75 VOLTS? SIGNAL HOLDS UNTIL VOLTAGE RISES ABOVE 75 VOLTS.
DS1 AND DS2 ALTERNATING FAST FLASH.
YES
NO COMBUSTION AIR INDUCER OFF, IGNITER OFF.

IS THERE A PROPER GROUND? SIGNAL HOLDS UNTIL UNIT IS PROPERLY GROUNDED.
DS1 AND DS2 ALTERNATING FAST FLASH.
NO COMBUSTION AIR INDUCER OFF, IGNITOR OFF.

IS IGNITOR INTACT AND CONNECTED? SIGNAL HOLDS UNTIL IGNITOR IS REPLACED
OR RECONNECTED.
YES DS1 AND DS2 ALTERNATING FAST FLASH.
AT END OF IGNITOR 20 SECOND WARM UP

PERIOD, 4−SECOND TRIAL FOR IGNITION.
GAS VALVE OPENS, IGNITOR ENERGIZED DURING
4−SECOND TRIAL UNTIL FLAME SENSED.
YES
4−SECOND FLAME STABILIZATION PERIOD.

INDUCER ON. INDOOR BLOWER OFF.
FLAME RECTIFICATION CURRENT CHECK DS1 SLOW FLASH, DS2 FAST FLASH,
CAN FLAME BE PROVEN WITHIN 4 NO ON/OFF LED OFF, HEAT LED 0N.
SECONDS AFTER GAS VALVE OPENS? HAS CONTROL FAILED TO SENSE NO
(u0.16 microamps) FLAME FOR FIVE CONSECUTIVE TRIES
DURING A SINGLE HEAT DEMAND?
YES
WATCHGUARD MODE. GAS VALVE OFF,

COMBUSTION AIR INDUCER OFF.
INDOOR BLOWER OFF. YES
DS1 AND DS2 ALTERNATING SLOW FLASH.
ON/OFF LED 0FF, HEAT LED OFF.
IS 60−MINUTE RESET PERIOD COMPLETE?
YES
FLAME PRESENT? NO
HAS CONTROL RESET IGNITION SEQUENCE
FOUR (4) TIMES? NO
YES
DS1 SLOW FLASH, DS2 FAST FLASH,
CONTINUED ON NEXT PAGE ON/OFF LED OFF, HEAT LED ON .
Page 72
CONTINUED THERMOSTAT CALLS FOR HEAT.
SEE BOX A.
FLAME SIGNAL ABOVE NO
(u0.23 microamps) LOW FLAME SIGNAL
(Does not affect control operation)
YES DS1 SLOW FLASH, DS2 FAST FLASH.
YES
SINGLE−STAGE THERMOSTAT MODE TWO STAGE THERMOSTAT MODE

(E20 SET AT SINGLE") (E20 SET AT TWO")
YES YES
START SECOND−STAGE RECOGNITION 45−SECOND INDOOR BLOWER ON DELAY BEGINS.

ON DELAY (10 OR 15 MINUTES). DS1 AND DS2 SIMULTANEOUS FAST FLASH.
YES
PRESSURE SWITCH CLOSED? YES PRIMARY LIMIT AND
ROLLOUT SWITCH CLOSED?
YES NO NO
NO C GAS VALVE OFF, COMBUSTION AIR INDUCER OFF,

FIRST−STAGE HEAT DEMAND SATISFIED? INDOOR BLOWER ON. DS1 SLOW FLASH, DS2 ON,
DS1 AND DS2 SIMULTANEOUS SLOW FLASH. ON/OFF LED ON, HEAT LED ON.
YES
GAS VALVE OFF, COMBUSTION AIR INDUCER HAS PRIMARY LIMIT OR ROLLOUT
OFF FOLLOWING POST PURGE. SWITCH CLOSED WITHIN 3 MINUTES? YES
INDOOR BLOWER OFF WITH DELAY (Indoor blower on low speed during 3−minute period)
DS1 AND DS2 SIMULTANEOUS SLOW FLASH
NO
SECOND−STAGE HEAT DEMAND. LIMIT SWITCH WATCHGUARD MODE.
SECOND−STAGE HEAT DEMAND REQUIRED? GAS VALVE OFF, COMBUSTION AIR INDUCER OFF,
DS1 AND DS2 SIMUTANEOUS SLOW FLASH. INDOOR BLOWER OFF WITH DELAY. YES
DS1 AND DS2 ALTERNATING SLOW FLASH,
YES ON/OFF LED OFF, HEAT LED OFF.
IS 60−MINUTE RESET PERIOD COMPLETE?
SECOND−STAGE 30−SECOND DELAY ON BEGINS.
YES INDOOR BLOWER OFF AFTER DELAY.
DS1 OFF, DS 2 SLOW FLASH,
SECOND−STAGE COMBUSTION AIR INDUCER ON/OFF LED OFF, HEAT LED ON.
ON. SECOND−STAGE GAS VALVE ON. HIGH
HEAT INDOOR BLOWER SPEED ON.
ON/OFF LED ON.
YES
PRESSURE SWITCH CLOSED GAS VALVE OFF. COMBUSTION AIR INDUCER ON.
IN LESS THAN TEN (10) SECONDS? NO INDOOR BLOWER OFF AFTER DELAY.
DS1 AND DS2 SIMULTANEOUS FAST FLASH. DS1 OFF, DS 2 SLOW FLASH,
ON/OFF LED OFF, HEAT LED ON.
YES
CONTINUED ON NEXT PAGE
Page 73
CONTINUED
SEE BOX A
NORMAL OPERATION
DS1 AND DS2 SIMULTANEOUS SLOW FLASH.
SEE BOX B
THERMOSTAT CALLS FOR HEAT
DS 1 AND DS 2 SIMULTANEOUS FAST
FLASH.
INDOOR BLOWER ON. YES
ARE PRIMARY LIMIT AND ROLLOUT NO DS1 SLOW FLASH, DS2 ON,
SWITCH CLOSED? ON/OFF LED ON, HEAT LED 0N.
HAS PRIMARY LIMIT OR ROLLOUT SWITCH
YES
CLOSED WITHIN 3 MINUTES?
NO
LIMIT SWITCH WATCHGUARD MODE. GAS VALVE
OFF. COMBUSTION AIR INDUCER OFF. INDOOR
YES
BLOWER OFF WITH DELAY. IS 60−MINUTE RESET
PERIOD COMPLETE? DS SLOW FLASH, DS2 ON,
GAS VALVE OFF, COMBUSTION AIR INDUCER

OFF AFTER 15 SECOND POST PURGE, INDOOR
PRESSURE SWITCH CLOSED? NO BLOWER OFF AFTER DELAY. YES
DS1 OFF, DS2 FAST FLASH,
ON/OFF LED ON, HEAT LED ON.
YES RETURN TO HEAT DEMAND?
HEAT DEMAND SATISFIED?

YES YES
SINGLE−STAGE THERMOSTAT MODE TWO STAGE THERMOSTAT MODE?

(E20 SET AT SINGLE") (E20 SET AT TWO")
YES YES
SECOND STAGE HEAT
HEAT DEMAND SATISFIED? FIRST AND SECOND STAGE HEAT DEMAND SASTISFIED?
NO
DS1 AND DS2 DEMAND SATISFIED SIMULTANEOUSLY. DS1 AND DS2
SIMULTANEOUS FAST FLASH. DS1 & DS2 SIMULTANEOUS FAST FLASH. SIMULTANEOUS FAST FLASH.
YES YES YES

GAS VALVE OFF, COMBUSTION AIR GAS VALVE, COMBUSTION AIR INDUCER
INDUCER OFF AFTER 5−SECOND AND INDOOR BLOWER RETURN TO FIRST−
LOW SPEED POST PURGE PERIOD, STAGE OPERATION.
INDOOR BLOWER OFF DELAY DS1 AND DS2 SIMULTANEOUS FAST FLASH.
INITIATED ON LOW HEAT SPEED.
DS1 AND DS2
SIMULTANEOUS FAST FLASH FIRST STAGE HEAT DEMAND SATISFIED?
YES
DEMAND FOR HEAT SATISFIED. GAS VALVE OFF. COMBUSTION AIR INDUCER
POWER ON STAND BY. OFF AFTER 5−SECOND LOW SPEED POST−
DS1 AND DS2 PURGE PERIOD. INDOOR BLOWER OFF.
SIMULTANEOUS SLOW FLASH DELAY INITIATED ON LOW HEAT SPEED.
DS1 & DS2 SIMULTANEOUS FAST FLASH.
Page 74
COOLING SEQUENCE OF OPERATION
POWER ON
YES
IS POLARITY REVERSED? SIGNAL POLARITY REVERSED.
DS1 FAST FLASH, DS2 SLOW FLASH.
SIGNAL IMPROPER NO
GROUND AT DS. NO NO
SIGNAL HOLDS IS THERE YES IS VOLTAGE LOW VOLTAGE SIGNAL AT DS HOLDS
UNTIL UNIT IS PROPER GROUND? ABOVE 75 VOLTS? UNTIL VOLTAGE RISES ABOVE 75 VOLTS.
PROPERLY YES
GROUNDED.
(V MODELS ONLY)
THERMOSTAT CALLS FOR FIRST−STAGE COOL.
COMPRESSOR AND CONDENSER FAN

ENERGIZED.
INDOOR BLOWER ENERGIZED ON FIRST STAGE

COOL SPEED AFTER 2 SECOND DELAY.
YES COMPRESSOR AND CONDENSER FAN DE−ENERGIZED.

FIRST−STAGE DEMAND FOR COOL SATISFIED?
INDOOR BLOWER DE−ENEGIZED.
NO
THERMOSTAT CALLS FOR SECOND−STAGE COOL.
INDOOR BLOWER RAMPS UP TO SECOND−STAGE COOL SPEED.
SECOND−STAGE DEMAND FOR COOL SATISFIED?
YES
UNIT RETURNS TO FIRST STAGE COOL
Page 75
CONTINUOUS LOW SPEED FAN SEQUENCE OF OPERATION
GHR32V−5 UNITS
MANUAL FAN SELECTION MADE AT THERMOSTAT.
AFTER 2 SECOND DELAY, INDOOR BLOWER IS
ENERGIZED ON CONTINUOUS FAN SPEED.
YES YES
THERMOSTAT CALLS FOR FIRST STAGE COOL. THERMOSTAT CALLS FOR FIRST−STAGE HEAT.
YES YES
INDOOR BLOWER RAMPS TO FIRST STAGE AFTER 45−SECOND DELAY, INDOOR BLOWER
COOLING SPEED AFTER A 2−SECOND DELAY. SWITCHES TO LOW HEAT SPEED.
YES
FIRST−STAGE COOL DEMAND SATISFIED? FIRST−STAGE HEAT DEMAND SATISFIED.
YES
NO NO
SECOND STAGE COOL DEMAND THERMOSTAT CALLS FOR SECOND−STAGE HEAT.
YES
INDOOR BLOWER RAMPS TO SECOND INDOOR BLOWER SWITCHES TO HIGH HEAT SPEED
STAGE COOL SPEED AFTER 30−SECOND RECOGNITION PERIOD.
YES
SECOND STAGE COOL DEMAND SATISFIED? SECOND−STAGE HEAT DEMAND SATISFIED.
YES YES
INDOOR BLOWER RAMPS DOWN TO FIRST STAGE INDOOR BLOWER RAMPS DOWN TO LOW
COOL SPEED. HEAT SPEED.
GHR32Q−5 UNITS
NOTE − Continuous low speed fan and cooling low speed are equal to the low heat fan speed.
MANUAL FAN SELECTION MADE AT THERMOSTAT.

AFTER 2 SECOND DELAY, INDOOR BLOWER IS
ENERGIZED ON CONTINUOUS FAN SPEED
(LOW HEAT / LOW COOL).
YES YES
THERMOSTAT CALLS FOR FIRST−STAGE COOL. THERMOSTAT CALLS FOR FIRST−STAGE HEAT.
YES YES
COMPRESSOR IS ENERGIZED AND INDOOR BURNERS IGNITE AND INDOOR BLOWER
BLOWER CONTINUES TO OPERATE IN LOW CONTINUES TO OPERATE IN CONTINUOUS
COOL SPEED. LOW (LOW HEAT / LOW COOL) MODE.
FIRST−STAGE COOL DEMAND SATISFIED? FIRST−STAGE HEAT DEMAND SATISFIED.

YES YES
NO NO
SECOND−STAGE COOL DEMAND THERMOSTAT CALLS FOR SECOND−STAGE HEAT.
YES
INDOOR BLOWER SWITCHES TO INDOOR BLOWER SWITCHES TO HIGH HEAT SPEED
SECOND−STAGE COOL SPEED AFTER 30−SECOND RECOGNITION PERIOD.
YES
SECOND−STAGE COOL DEMAND SATISFIED? SECOND−STAGE HEAT DEMAND SATISFIED.
YES YES
INDOOR BLOWER SWITCHES TO FIRST−STAGE INDOOR BLOWER SWITCHES TO LOW HEAT
COOL SPEED. SPEED.
Page 76
IX− Troubleshooting
SureLight Control
UPON INITIAL POWER UP, REMOVE ALL THERMOSTAT DEMANDS TO THE UNIT
Unless otherwise noted, condition applies to all GHR32Q/V units.
PROBLEM: 1 UNIT FAILS TO OPERATE IN THE COOLING, HEATING, OR CONTINUOUS FAN MODE
Condition Possible Cause Corrective Action / Comments
1.1 1.1.1
ACTION 1 − Check 120V main voltage.
− Both diagnostic lights fail to light up. Main voltage 120V not supplied to unit. Determine cause of main power failure.
1.1.2 ACTION 1 − Check for correct wiring of 120V to

LED#1−Off power make up box and transformer.
LED#2−Off Miswiring of furnace or improper con-
ACTION 2 − Check 24V wiring to control board.
nections.
1.1.3 ACTION 1 − Replace circuit breaker if it is reset
but does not have continuity.
Circuit breaker tripped or fails to ACTION 2 − If circuit breaker still trips, check for
close. short.
ACTION 1 − Check that door switch is activated
when door is closed.
1.1.4 ACTION 2 − Check wire connections to switch, re-
place loose connectors.
Door interlock switch failure. ACTION 3 − Check continuity of switch in closed
position. Replace if malfunctioning
1.1.5 ACTION 1 − Check that transformer output is
24V. Replace if malfunctioning
Transformer Failure.
1.1.6 ACTION 1 − If all the above items have been
checked, replace board.
Failed control board.
1.2 ACTION 1 − Manually reset the roll−out switch
1.2.1 by pushing the top button.
GHR32Q/V−1 through −4 Units Only
Roll−out switch open. ACTION 2 − Determine the cause of the roll−out
− Diagnostic lights flash the roll−out
roll out switch activation before leaving furnace.
code. 1.2.2 ACTION 1 − Check continuity across roll−out
switch. Replace roll−out switch if switch is reset
Roll−out switch failure. but does not have continuity.
1.2.3
LED#1−On,
LED#1−On Miswiring
Mis iring or improper connections at ACTION 1 − Check wiring connections to switch.
switch
LED#2−Slow Flash roll−out switch.
ACTION 1 − Check 9−pin connector for proper
1.2.4 connection to control board.
Nine pin connector failure ACTION 2 − Check continuity of the multi plug
pin.
1.3
− On initial power−up the comb. air
blower does not energize.
ACTION 1 − Check the 120V has line and neutral
− Diagnostic lights flash the reverse 1.3.1 correctly input into control.
polarity code. ACTION 2 − Reverse the line and neutral at the
120V main power polarity reversed.
120V field connection.
LED#1−Fast Flash,
LED#2−Slow Flash.
1.4
GHR32Q/V−1 through −4 Units Only 1.4.1 ACTION 1 − Check for 120V to combustion air
− On initial power up the combustion Open combustion air blower motor cir- blower. If no power, check wire and connec-
air blower does not energize. tions.
cuit.
− Diagnostic lights flash normal power
on operation
operation.
1.4.2 ACTION 1 − If power is present at blower, replace
blower.
LED#1−Slow Flash Failed combustion air blower motor.
LED#2−Slow Flash
Page 77
PROBLEM 1: UNIT FAILS TO OPERATE IN THE COOLING, HEATING, OR CONTINUOUS FAN MODE
1.5 1.5.1
ACTION 1 − Check that the unit is properly
grounded.
− On initial power−up the combustion Improper ground to the unit. ACTION 2 − Install a proper main ground to the
air blower remains energized.
g unit
− Diagnostic lights flash the improper 1.5.2 ACTION 1 − Check 6−pin connector for proper
main ground. installation. Correctly insert connector into con-
6−Pin connector is improperly at-
trol.
tached to the circuit board.
LED#1−Alternating Fast Flash 1.5.3 ACTION 1 − Check that the line voltage is above
LED#2−Alternating Fast Flash 75V. Determine cause of voltage drop and supply
Line voltage is below 75V. correct voltage to the control.
PROBLEM 2: UNIT FAILS TO OPERATE IN THE COOLING OR HEATING MODE, BUT COMBUSTION
AIR BLOWER OPERATES CONTINUOUS. GHR32Q/V−1 through −4 UNITS WITH CONTROL BOARDS
DATE CODED AFTER NOV.1 1997, WILL OPERATE IN COOLING WITH COMBUSTION AIR BLOWER
CYCLING 5 SECONDS ON 55 SECONDS OFF, BUT NOT IN THE HEATING MODE.
2.1
− On initial power−up the combustion
2.1.1 ACTION 1 − Check for correct wiring and loose
air blower remains energized. connections in the ignitor circuit. Check multi −
− Diagnostic lights flash the improper Open ignitor circuit. plug connections for correct installation.
main ground.
− G32V−1 to −4 Units with control
boards date coded after Nov.1
Nov 1 1997;
combustion air blower will cycle 5
seconds on 55 seconds off. ACTION 1 − Unplug ignitor and read resistance
2.1.2
across ignitor. If resistance does not read be-
Broken or failed ignitor. tween 10.9 and 19.7 ohms, replace the ignitor.
LED#1−Alternating Fast Flash
LED#2−Alternating Fast Flash
PROBLEM 3: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER DOES NOT
ENERGIZE
3.1 ACTION 1 − Check continuity across switch(es).
− Unit operates with a cooling or contin- Switches reset automatically upon cool down.
3.1.1 Rollout switch must be reset manually.
uous fan demand. ACTION 2 − Check for restrictions on blower inlet
− Combustion air blower will not start Primary or secondary (if equipped) or
air (including filter) and outlet air. Determine
with a Heating demand. rollout limit switch open. cause for limit activation before placing unit back
− Diagnostic lights flash the limit failure in operation.
mode
mode.
Miswiring of furnace or improper con- connections. Correct wiring and/or replace any
LED#1−Slow Flash, loose connections.
LED#2−On nections at limit switch(es).
3.2
− Unit operates with a cooling and con- 3.2.1 ACTION 1 − Check for correct wiring and loose
tinuous fan demand. Miswiring of furnace or improper con- connections. Correct wiring and/or replace any
− Combustion air blower will not start loose connections.
nections to combustion air blower.
with a Heating demand.
− Diagnostic lights flash the pressure
switch failure code.
3.2.2 ACTION 1 − Check that the pressure switch is
open without the combustion air blower operat-
LED#1−Off, Pressure switch stuck closed. ing. Replace if malfunctioning
LED#2−Slow Flash
Page 78
PROBLEM 3: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER DOES NOT
ENERGIZE (CONT.).
Condition Possible Cause Corrective Action/Comments
3.3
− Unit operates with a cooling and con- 3.3.1 ACTION 1 − Check for correct wiring and loose
tinuous fan demand. connections. Correct wiring and/or replace any
Miswiring of furnace or improper con-
− Combustion air blower will not start loose connections.
nections to combustion air blower.
with a Heating demand.
− Diagnostic lights flash the pressure
switch failure code 2.5
2 5 minutes after
heating demand.
3.3.2 ACTION 1 − If there is 120V to combustion air
blower and it does not operate, replace combus-
Combustion air blower failure. tion air blower.
LED#1−Off,
LED#2−Slow Flash
PROBLEM 4: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER
ENERGIZES, IGNITOR IS NOT ENERGIZED.
4.1 4.1.1
ACTION 1 − Check that the pressure switch tub-
− Unit operates with a cooling and Pressure switch does not close due ing is correctly routed. Correctly route pressure
continuous fan demand. to incorrect routing of the pressure switch tubing.
− Combustion air blower energizes switch tubing.
with a heating demand.
demand
4.1.2
− Diagnostic lights flash the pressure ACTION 1 − Remove any obstructions from the
switch failure code 2.5 minutes after Pressure switch does not close due pressure tubing and/or taps.
heatingg demand. to obstructions in the pressure tubing.
4.1.3 ACTION 1 − Check pressure switch tubing for
leaks. Replace any broken tubing.
LED#1 Off
LED#1−Off Pressure switch tubing damaged
LED#2−Slow Flash 4.1.4 ACTION 1 − Check pressure switch tubing for
condensate. Remove condensate from tubing.
Condensate in pressure switch tub- Check that the condensate tubing is located cor-
ing. rectly.
ACTION 1 − Check the differential pressure

across the pressure switch. This pressure
4.1.5 should exceed the set point listed on the
Pressure switch does not close due switch.
to a low differential pressure across ACTION 2 − Check for restricted inlet and ex-
the pressure switch. haust vent. Remove all blockage.
ACTION 3 − Check for proper vent sizing and
run length. See installation instructions.
4.1.6
ACTION 1 − Check that the proper pressure
Wrong pressure switch installed in the switch is installed in the unit. Replace pressure
unit, or pressure switch is out of cal- switch if necessary.
ibration.
Miswiring of furnace or improper con- connections. Correct wiring and/or replace any
loose connections.
nections at pressure switch.
ACTION 1 − If all the above modes of failure have
4.1.8 been checked, the pressure switch may have
Pressure switch failure. failed. Replace pressure switch and determine if
unit will operate.
Page 79
PROBLEM 5: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER
ENERGIZES, IGNITOR IS ENERGIZED. (CONT.)
5.1 ACTION 1 − Check line pressure at the gas valve.
5.1.1 Pressure should not exceed 13" WC for both nat-
− Unit operates with a cooling and Check that gas is being supplied to ural and propane. Line pressure should read a
minimum 4.5" WC for natural and 8.0"WC for pro-
continuous fan demand. the unit. pane.
− Combustion air blower energizes
5.1.2
with Heating demand. ACTION 1 − Check for correct wiring and loose
− Ignitor is energized but unit fails to Miswiring of gas valve or loose con- connections. Correct wiring and/or replace any
nections at multi−pin control amp loose connections.
light. plugs or valve.
ACTION 1 − Check that 24V is supplied to the gas
valve approximately 35 seconds after heat de-
5.1.3 mand is initiated.
LED#1−Alternating Slow Flash ACTION 2 − Replace the valve if 24V is supplied
LED#2−Alternating Slow Flash Malfunctioning gas valve or ignition but valve does not open (check for excessive gas
control. line pressure before replacing gas valve).
ACTION 3 − Replace the control board if 24V is
not supplied to valve.
PROBLEM 6: BURNERS LIGHT WITH A HEATING DEMAND BUT UNIT SHUTS DOWN
PREMATURELY
6.1.1 ACTION 1 − Check vent termination kit installed.
6.1 1−1/2" dia. concentric vent (kit60G77) for 50 and
Wrong concentric vent kit used for 75 inputs and 2" dia. concentric vent (kit 33K97)
− Burners fire with a heating demand. terminating the unit. for 100 &125 inputs.
− Burners light but unit shuts off prior
ACTION 1 − Check condensate line for proper
to satisfying T−stat demand. 6.1.2 vent slope, and any blockage. Condensate
− Diagnostic lights flash the pressure should flow freely during operation of furnace.
Condensate drain line is not draining
switch code. Repair or replace any improperly installed con-
properly. densate lines.
6.1.3 ACTION 1 − Check for restricted vent inlet or ex-
LED#1−Off haust. Remove all blockage.
LED#2−Slow Flash Low pressure differential at the pres- ACTION 2: Check for proper vent sizing. See
sure switch. installation instructions.
6.2 6.2.1 ACTION 1 − Check that sensor is properly lo-

cated (page 10) and that the sense wire is
− Combustion air blower energizes with Sensor or sense wire is improperly properly attached to both the sensor and the
a heating demand. installed. control.
− Burners
B light
li ht but
b t fail
f il to
t stay
t lit
lit. ACTION 1 − Check for a broken sensor.
− After 5 tries the control diagnostics 6.2.2 ACTION 2 − Test continuity across the sense
flash the watchguard burners failed to Sensor or sense wire is broken. wire. If wire or sensor are damaged replace the
ignite code. component.
ACTION 1 − Check for resistance between the
6.2.3 sensor rod and the unit ground.
Sensor or sensor wire is grounded to ACTION 2 − Check for resistance between the
LED#1−Alternating Slow Flash sensor wire and the unit ground.
LED#2−Alternating Slow Flash the unit. ACTION 3 − Correct any shorts found in circuit.
ACTION 1 − Check the microamp signal from
the burner flame. If the microamp signal is be-
low normal, check the sense rod for proper
location or contamination.
6.2.4 ACTION 2 − Replace, clean, or relocate flame
sense rod. If rod is to be cleaned, use steel
Control does not sense flame. wool or replace sensor. DO NOT CLEAN ROD
WITH SAND PAPER. SAND PAPER WILL
CONTRIBUTE TO THE CONTAMINATION
PROBLEM. NOTE: Do not attempt to bend
sense rod.
Page 80
PROBLEM 6: BURNERS LIGHT WITH HEATING DEMAND BUT UNIT SHUTS DOWN
PREMATURELY (CONT.)
6.3 ACTION 1 − Check that the manifold pressure
matches value listed on nameplate. See installa-
− Combustion air blower energizes tion instructions for proper procedure.
with a heating demand. 6.3.1 ACTION 2 − Verify that the installed orifice size
− Burners light. match the size listed on the nameplate or installa-
Unit is firing above 100% of the tion instructions.
− Roll−out switch trips during the nameplate input. ACTION 3 − Check gas valve sensing hose to in-
heating demand. sure no leaks are present.
− Diagnostic lights flash roll−out fail- ACTION 4 − Check the input rate to verify rate
ure. matches value listed on nameplate.
ACTION 1 − Tighten orifice until leak is sealed.
6.3.2 NOTE: Be careful not to strip orifice threads.
GHR32Q/V−1 through −4 Units Only Gas orifices leak at the manifold con- ACTION 2 − Check for gas leakage at the
threaded orifice connection. Use approved meth-
LED#1−On nection. od for leak detection (see unit instructions).
LED#2−Slow Flash
6.3.3 ACTION 1 − Check for air leakage at all joints in
the heat exchanger assembly. Condition may
Air leakage at the connections because high CO2 with high CO.
GHR32Q/V−5 Units tween the primary heat exchanger, ACTION 2 − Seal leakage if possible (high tem-
LED#1−Slow Flash perature silicon is recommended), replace heat
secondary heat exchanger, and com- exchanger if necessary, tag and return heat ex-
LED#2−On bustion air blower. changer to proper Lennox personnel.
ACTION 1 − Check for sooting deposits or other
restrictions in the heat exchanger assembly.
6.3.4 Clean assembly as outlined in instruction manu-
al.
Insufficient flow through the heat ex- ACTION 2 − For GHR32 gas furnaces, check for
changer caused by a sooted or re- proper combustion and flow. CO2 should mea-
stricted heat exchanger. sure between 6.0% and 8.0% for NAT and 7.0%
and 9.0% for LP. CO should measure below .04%
(400PPM) in an air−free sample of flue gases.
6.3.5 ACTION 1 − Check that the burners are firing into
Burners are not properly located in the center of the heat exchanger openings. Cor-
rect the location of the burners if necessary.
the burner box.
6.4
6.4.1 ACTION 1 − Check for proper flow of exhaust
− Combustion air blower energizes gases away from intake vent. Remove any ob-
with a heating demand. Recirculation of flue gases. This con- stacles in front of the intake and exhaust vent
− Burners light roughly and the unit dition causes rough ignitions and op- which would cause recirculation.
fails to stay lit. eration. Problem is characterized by ACTION 2 − Check for correct intake and exhaust
nuisance flame failures. vent installation.
− Diagnostic lights flash watchguard
flame failure.
ACTION 1 − Remove burner and inspect the

6.4.2 cross−overs for burrs, or any restriction or if
LED#1−Alternating Slow Flash
Improper burner cross−overs crossover is warped. Remove restriction or re-
LED#2−Alternating Slow Flash place burners.
Page 81
PROBLEM 6: BURNERS LIGHT WITH HEATING DEMAND BUT UNIT SHUTS DOWN
PREMATURELY (CONT.)
6.5
− Combustion air blower energizes
with a heating demand.
− Burners light.
− Diagnostic lights flash watch guard ACTION 1 − Check that the sensor is properly lo-
flame failure. 6.5.1 cated.
− NOTE" Unit might go into 60 minute Loose sensor wire connection causes ACTION 2 − Check that the sense wire is properly
attached to both the sensor and the control. Pay
Watchguard mode depending on in- intermittent loss of flame signal. extra attention to the pin connectors.
termittent nature of sensor signal.

PROBLEM 7: CONTROL SIGNALS LOW FLAME SENSE DURING HEATING MODE
7.0 7.1.1 ACTION 1 − Check the sense rod for proper loca-
− Unit operates correctly but the diag- Sense rod is improperly located on tion on the burner. Properly locate the sense rod
nostic lights flash low flame sense or replace if rod cannot be located correctly.
the burner.
code
code.
ACTION 1 − Check sense rod for contamination
or coated surface. Clean the sense rod with steel
7.1.2 wool or replace sensor. DO NOT USE SAND PA-
LED#1−Slow Flash PER TO CLEAN ROD. SAND PAPER WILL
Sense rod is contaminated.
LED#2−Fast Flash CONTRIBUTE TO THE CONTAMINATION
PROBLEM.
PROBLEM 8: RF STATIC DURING TIME FOR IGNITION

8.0 8.1.1
ACTION 1− Call Technical Support, Dallas
− AM radio interference Ignitor operation
Page 82
VSP2−1 Blower Control Board GHR32V−1 / −3 Units
DOES UNIT OPERATE?
YES NO CHECK:
NO 1−UNIT POWER
IS 24VAC ACROSS 2−INTERLOCK SWITCH
R AND C? 3−TRANSFORMER
COOLING MODE YES 4−LIMIT SWITCH
PLACE JUMPER ACROSS R AND G.
IS BLOWER ON LOW SPEED AND IS

ON/OFF" LED−DS3 LIT? CFM" LED−DS4 NO CHECK UNIT WIRING
LIGHT SHOULD BLINK ONCE FOR EV- AND IF CORRECT,
ERY 100 CFM SELECTED IN THE REPLACE VSP2−1.
TABLES ON PAGE 2.
YES
IS 24 VOLTS PRESENT AT J73 NO
PIN 12 ON VSP2 BOARD? REPLACE VSP2−1.
YES
IN ADDITION TO R AND G,
JUMPER R AND DS.
YES NO
IS BLOWER ON HIGH SPEED AND ARE DS1 AND CHECK UNIT WIRING
END OF COOLING TEST
DS3 LIT? DOES THE CFM" LED−DS4 LIGHT BLINK AND IF CORRECT
ONCE FOR EVERY 100 CFM SELECTED IN THE REPLACE THE
TABLES ON PAGE 2? VSP2−1.
DOES UNIT OPERATE?
YES CHECK:
NO 1−UNIT POWER
IS 24VAC ACROSS
R AND C? 2−INTERLOCK SWITCH
3−TRANSFORMER
YES 4−LIMIT SWITCH
HEATING MODE
PLACE HTG. BLOWER" JUMPER IN POSITION #2.
PLACE JUMPER ACROSS R AND W1. WAIT 75
SECOND FOR PREPURGE AND FANON" DELAY.
1−CHECK UNIT WIRING AND IF
CORRECT, REPLACE
IS BLOWER ON LOW SPEED AND IS ON/OFF" LED− NO 2−BREAK AND REMAKE JUMPER
VSP2−1.
DS3 LIT? CFM" LED−DS4 LIGHT SHOULD BLINK (R TO W1).
ONCE FOR EVERY 100 CFM SELECTED IN THE 3−AFTER 30−35 SECOND
TABLES ON PAGE 2. PURGE, IS 24VAC PRESENT
AT GAS VALVE?
YES
YES
PLACE HTG. BLOWER"
JUMPER IN POSITION #1.
R AND W1 REMAIN JUMPERED.
DOES BLOWER SHIFT TO HEAT SPEED

AND IS HEAT" LED−DS2 ON? DOES THE NO CHECK UNIT WIRING
CFM" LED−DS4 LIGHT BLINK ONCE AND IF CORRECT,
FOR EVERY 100 CFM SELECTED IN REPLACE VSP2−1.
THE TABLES ON PAGE 2?
YES
REMOVE JUMPERS
YES AFTER THE SELECTED NO

END OF TEST TIME, DOES BLOWER REPLACE THE VSP2−1.
TURN OFF?
Page 83
VSP3−1 Blower Control Board GHR32V−4 Units
DOES UNIT OPERATE?
YES NO CHECK:
NO 1−UNIT POWER
IS 24VAC ACROSS 2−INTERLOCK SWITCH
R AND C? 3−TRANSFORMER
COOLING MODE YES 4−LIMIT SWITCH
PLACE JUMPER ACROSS R, G, AND Y1.
IS BLOWER ON LOW SPEED AND IS ON/

OFF LED−DS3 AND HI/LOW LED−DS1 LIT? NO CHECK UNIT WIRING AND IF
CFM LED−DS4 LIGHT SHOULD BLINK ONCE CORRECT, REPLACE VSP3−1.
FOR EVERY 100 CFM SELECTED IN THE
TABLES ON PAGE 2.
YES

YES
IN ADDITION TO R G, AND Y1
JUMPER R AND Y2.
YES NO
END OF COOLING TEST IS BLOWER ON HIGH SPEED AND ARE DS1 AND CHECK UNIT WIRING
DS3 LIT? DOES THE CFM LED−DS4 LIGHT BLINK AND IF CORRECT
ONCE FOR EVERY 100 CFM SELECTED IN THE REPLACE THE
TABLES ON PAGE 2? VSP3−1.
DOES UNIT OPERATE?
YES CHECK:
NO 1−UNIT POWER
IS 24VAC ACROSS
R AND C? 2−INTERLOCK SWITCH
3−TRANSFORMER
YES 4−LIMIT SWITCH
HEATING MODE
PLACE HTG. BLOWER JUMPER IN POSITION #2.
PLACE JUMPER ACROSS R AND W1. WAIT 75 SEC-
OND FOR PREPURGE AND FAN ON DELAY.
1−CHECK UNIT WIRING AND IF
IS BLOWER ON LOW SPEED AND IS ON/OFF" NO CORRECT, REPLACE VSP3−1.
2−BREAK AND REMAKE JUMPER
LED−DS3 LIT? CFM" LED−DS4 LIGHT SHOULD
(R TO W1).
BLINK ONCE FOR EVERY 100 CFM SELECTED IN 3−AFTER 30−35 SECOND PURGE,
THE TABLES ON PAGE 2. IS 24VAC PRESENT AT GAS
VALVE?
YES
YES
PLACE HTG. BLOWER
JUMPER IN POSITION #1.
R AND W1 REMAIN JUMPERED.
DOES BLOWER SHIFT TO HIGH SPEED

AND IS HEAT" LED−DS2 ON? DOES THE NO CHECK UNIT WIRING
CFM" LED−DS4 LIGHT BLINK ONCE FOR AND IF CORRECT,
EVERY 100 CFM SELECTED IN THE REPLACE VSP3−1.
TABLES ON PAGE 2?
YES
REMOVE JUMPERS
YES AFTER THE SELECTED NO

END OF TEST REPLACE THE VSP3−1.
TIME, DOES BLOWER
TURN OFF?
Page 84
ICM−2 WITH VSP2
120V to the motor must not be interupted. All connections for check out
will be from the voltage source below (battery or 24V) to plug J46, after
disconnectiong from blower control board VSP2.
J46
1
13 1 13
CHECK−OUT PROCEDURE USING BATTERY CHECK−OUT PROCEDURE USING 24V SOURCE

An ordinary 9 volt battery with maximum DC Unit transformer T1 with a maximum AC 30 volts
20volts is recommended. A 9 volt battery will may be used in lieu of a battery. If transformer T1
last for about one day of normal operation. is used, double check all wiring connections be-
fore placing unit back in operation.
LOW SPEED CHECK−OUT LOW SPEED CHECK−OUT

1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13
J46 J46
C
1− Disconnect power to unit. R
1− Disconnect power to unit.
2− Disconnect plug J46 from P46 located on the 2− Disconnect plug J46 from P46 located on the
blower control board. blower control board.
3− Connect voltage source as shown above. 3− Disconnect C and R from control board.
4− Turn on power to unit. Blower should operate 4− Connect voltage source as shown above.
at low speed.
5− Turn on power to unit. Blower should operate
at low speed.
HIGH SPEED CHECK−OUT HIGH SPEED CHECK−OUT

1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13
J46 J46
C
6− Connect voltage source as shown above. 6− Disconnect power to unit.
7− Turn on power to unit. Blower should operate 7− Connect voltage source as shown above.
at high speed. 8− Turn on power to unit. Blower should operate
at high speed.
HEATING SPEED CHECK−OUT HEATING SPEED CHECK−OUT

1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13
J46 J46
C
10−Turn on power to unit. Blower should operate 10− Connect voltage source as shown above.
at heating speed. 11− Turn on power to unit. Blower should operate
at heating speed.
A kit is available from the Lennox parts center to use in testing the variable speed motor. The kit 70J11 includes a test plug
harness to facilitate ICM−2 check−out. Follow testing procedures outlined in the instructions provided with the kit.
The testing procedures are different than those listed above.
Page 85
ICM−2 WITH VSP3
120V to the motor must not be interupted. All connections for check out
will be from the voltage source below (battery or 24V) to plug J46, after
disconnectiong from blower control board.
CHECK−OUT PROCEDURE USING BATTERY CHECK−OUT PROCEDURE USING 24V SOURCE
An ordinary 9 volt battery with maximum DC Unit transformer T1 with a maximum AC 30 volts
20volts is recommended. A 9 volt battery will may be used in lieu of a battery. If transformer T1
last for about one day of normal operation. is used, double check all wiring connections be-
fore placing unit back in operation.
LOW COOL SPEED LOW COOL SPEED
1 2 3 4 5 6 7 8 9 10 11 12 13
1 2 3 4 5 6 7 8 9 10 11 12 13
J46 J46
To Y" on ignition control. !
C
1− Disconnect power to unit. R 1− Disconnect power to unit.
2− Disconnect plug J46 from P46 located on the 2− Disconnect plug J46 from P46 located on the
blower control board. blower control board.
3− Connect voltage source as shown above. 3− Disconnect C and R from ignition control
board.
4− Turn on power to unit. Blower should operate
at low cool speed. 4− Disconnect Y" from ignition control and con-
nect a seperate wire between R" on the
transfomer and Y" on the ignition control.
5− Connect voltage source as shown above.
To Y2" on TB1.! 6− Turn on power to unit. Blower should operate
HIGH COOL SPEED at low cool speed.
To Y" on ignition control. !
1 2 3 4 5 6 7 8 9 10 11 12 13 HIGH COOL SPEED
1 2 3 4 5 6 7 8 9 10 11 12 13
J46
6− Connect voltage source as shown above. To Y2" on TB1.!
7− Disconnect Y" on ignition control AND re- C
R
move connection from Y2" on TB1 in control 7− Disconnect power to unit.
box. Connect a seperate wire between the − 8− Connect voltage source as shown above.
side of the battery and BOTH Y" on the igni- 9− Disconnect Y2" on TB1 in control box and
tion control and Y2" on TB1. connect a seperate wire between R" on
transformer and Y2" on TB1.
8− Turn on power to unit. Blower should operate 10− Turn on power to unit. Blower should oper-
at high cool speed. ate at high cool speed.
LOW HEAT SPEED LOW HEAT SPEED

1 2 3 4 5 6 7 8 9 10 11 12 13
1 2 3 4 5 6 7 8 9 10 11 12 13
J46 J46
To W" on ignition control board. ! To W" on on ignition control. !

C
R
9− Disconnect power to unit. 11− Disconnect power to unit.
10− Connect voltage source as shown above. 11− Connect voltage source as shown above.
11− Disconnect W" terminal on ignition control 12− Disconnect W" from ignition control and
board and connect a seperate wire between connect a seperate wire between R" on
W" and + side of battery. transformer and W" on the ignition control.
12− Turn on power to unit. Blower should oper- 13− Turn on power to unit. Blower should operate
ate at low heat speed. at low heat speed.
HIGH HEAT SPEED HIGH HEAT SPEED

1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13
J46 J46
To W2" on TB1 ! To W2" on TB1 !
C
13− Disconnect power to unit. R 14− Disconnect power to unit.
15−Disconnect W2" on TB1 in control box and
16− Disconnect W2" from TB1and connect a
connect a seperate wire between W2" and + seperate wire between R" on transformer
side of battery. and W2" on TB1.
16−Turn on power to unit. Blower should operate 17− Turn on power to unit. Blower should operate
at low heat speed.
at high heat speed.
Page 86
ICM−2 WITH TWO STAGE VARIABLE SPEED CONTROL BOARD
120V to the motor must not be interrupted. All connections for check out will be from the volt-
age source below (battery or 24V) to plug J46, after disconnecting from blower control board.
REMOVE PLUG FROM BOARD
1 16
CHECK−OUT PROCEDURE USING 24V SOURCE

CHECK−OUT PROCEDURE USING BATTERY
Unit transformer T1 with a maximum AC 30 volts
An ordinary 9 volt battery with maximum DC may be used in lieu of a battery. If transformer T1
20volts is recommended. A 9 volt battery will is used, double check all wiring connections be-
last for about one day of normal operation. fore placing unit back in operation.
LOW C
COOL J46
LOW R
SPEED COOL J46

SPEED

2− Disconnect plug J46 from P46 located on the blower control board. 1− Disconnect power to unit.
3− Connect voltage source as shown above. 2− Disconnect plug J46 from P46 located on the blower control board.
4− Turn on power to unit. Blower should operate at low cool speed. 3− Connect voltage source as shown above.
4− Turn on power to unit. Blower should operate at low cool speed.
HIGH C
HIGH R
COOL COOL
J46 SPEED J46
SPEED

7− Turn on power to unit. Blower should operate at high cool speed. 6− Connect voltage source as shown above.
7− Turn on power to unit. Blower should operate at high cool speed.
C
R
LOW LOW
HEAT J46 HEAT J46
SPEED SPEED

10− Turn on power to unit. Blower should operate at low heat speed. 10− Turn on power to unit. Blower should operate at low heat speed.
C
HIGH HIGH R
HEAT HEAT
J46 J46
SPEED SPEED

13− Turn on power to unit. Blower should operate at high heat speed. 13− Turn on power to unit. Blower should operate at high heat speed.
Page 87
TABLE 35
GHR32V−1 / −3 UNITS OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP2−1 (HEATING)
MATCH UP T−Strip Mode of COMMENTS OR SEQUENCE
Jumper Operation
Jumper
FOR COOLING JUMPERS

SEE COOLING SECTION
BELOW
Single-Stage Heating No One−Stage Blower operates on the high

with Single−Stage Jumpers speed heat tap during the
Thermostat heating mode.
Two-Stage Heating No W2 Timed Blower operates on the low

With Single−Stage Jumpers speed heat/cool tap during the
Thermostat first stage of heating. Blower
Page 88
operates on the high speed

heat tap during second stage
heating.
Remove pin #3 of the J73

plug on the VSP control.
See fig. 16. Insulate end to
prevent it from shorting.
Harmony Heating No Two−Stage Blower operates on PWM

Jumpers signal generated by Har-
mony. Harmony overrides
blower speed taps. Blower
speed varies according to
zone demand.
Low and high fire controlled by
temperature modulating switch.
(continued on following page)

(continued from previous page)
GHR32V−1 / −3 UNITS OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP2−1 (HEATING CONTINUED)
MATCH UP T−Strip Mode of COMMENTS OR SEQUENCE
Jumper Operation
Jumper
Two−Stage Heating No Two−Stage Blower operates on the low

With Two−Stage Jumpers speed heat/cool tap during first
Thermostat stage heating. Blower operates
on high speed heat tap during
second stage heating.
GHR32V−1 / −3 UNITS OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP2−1 (COOLING)
MATCH UP T−STRIP JUMPER COMMENTS OR SEQUENCE
FOR HEATING JUMPERS

Page 89
SEE HEATING SECTION

ABOVE
DS to Y1" Blower operates on high speed
Single-Speed Com- (factory wired) cool tap during cooling.
pressor, no CCB1,
no Harmony
Remove Jumper Blower operates on low speed

DS to Y1" heat/cool during cooling
Y1
Two-Speed Compressor, DS" to Y2" Blower operates on low
no CCB1, no Harmony speed heat/cool tap when
Move factory compressor is in first
wired jumper from stage cooling. Blower op-
Y1 to Y2". erates on high speed cool
tap when compressor is in
second stage cooling. Y2

GHR32V−1 / −3UNITS OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP2−1 (COOLING CONTINUED)
FOR HEATING JUMPERS
SEE HEATING SECTION
ABOVE
Blower speed is controlled by

the DC signal from CCB1.
CCB1 with Single-Speed No Jumpers Blower operates on low speed
Compressor, no Harmony (Remove jumper heat/cool tap during dehumidifi-
from Y1 to DS") cation. Otherwise, blower oper-
ates on high speed cool tap
during cooling cycle.
Blower speed is controlled by

the DC signal from CCB1.
CCB1 with Two-Speed No Jumpers Blower operates on low speed
Page 90
Compressor, no Harmony (Remove jumper heat/cool tap during dehumidi-

from Y1 to DS") fication. Otherwise, blower op- Y1
erates on high speed cool tap
during high speed compressor
operation and low speed heat/
cool tap during low speed Y2
compressor operation.

GHR32V−1 / −3 UNITS OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP2−1 (COOLING CONTINUED)
MATCH UP T−STRIP JUMPER COMMENTS OR SEQUENCE WIRING CONNECTIONS
FOR HEATING JUMPERS
SEE SEE HEATING SECTION
ABOVE
terminal on the VSP con-
No Jumpers trol. Insulate end to pre-
Harmony and Single- (Remove vent shorting. Blower oper-
Speed Compressor jumper from ates on PWM signal gener-
Y1 to DS"). ated by Harmony. Harmony
overrides blower speed
taps. Blower speed varies
according to zone demand.

No Jumpers terminal on the VSP con-
Page 91
Harmony and Two- (Remove trol. Insulate end to pre-

Speed Compressor jumper from vent shorting. Blower oper-
Y1 to DS"). ates on PWM signal gener-
ated by Harmony. Harmony
overrides blower speed
taps. Blower speed varies
according to zone demand.
TABLE 36
GHR32V−4 OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP3−1 (HEATING)
MATCH UP T−Strip Mode of COMMENTS OR SEQUENCE WIRING CONNECTIONS
Jumper Operation
Jumper
FOR COOLING JUMPERS

SEE COOLING SECTION
BELOW No One−Stage Blower operates on
Jumpers high speed during the
Single-Stage Heating heating mode.
with Single−Stage
Thermostat
Two-Stage Heating No W2 Timed Blower operates on low

With Single−Stage Jumpers speed during the first stage
Page 92
Thermostat of heating. Blower operates

on high speed during
second−stage heating.
Remove pin #3 of the J73 plug on

the VSP control, and pins #2
and 13 of the J49 plug at the
motor. See fig 19 and 39. Insulate
ends to prevent them from shorting.
Harmony Heating No Two−Stage
Blower operates on PWM signal
Jumpers
generated by Harmony. Harmo-
ny overrides blower speed taps.
Blower speed varies according
to zone demand.
Low and high fire controlled by TEMPERATURE
temperature modulating switch. MODULATING
SWITCH

GHR32V−4 OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP3−1 (HEATING CONTINUED)
MATCH UP T−Strip Mode of COMMENTS OR SEQUENCE WIRING CONNECTIONS
Jumper Operation
Jumper
Two−Stage Heating No Two−Stage Blower operates on low

With Two−Stage Jumpers speed during first stage
Thermostat heating. Blower operates on
high speed during second
stage heating.
GHR32V−4 OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP3−1 (COOLING)

WIRING CONNECTIONS
Page 93
DS to Y1 Blower operates on high speed

FOR HEATING JUMPERS and Y1 to Y2
SEE HEATING SECTION during cooling.
and O to R
ABOVE
(factory wired)
Single-Speed Com-
pressor, no CCB1,
no Harmony Remove jumper Blower operates on low speed
DS to Y1 during cooling.
Two-Speed Compressor, DS to Y1 Blower operates on low speed Y1

no CCB1, no Harmony and cool when compressor is in
O to R first stage cooling.
Remove factory−wired Blower operates on high
jumper Y1 to Y2. speed cool when compressor
is in second stage cooling.
Y2

GHR32V−4 OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP3−1 (COOLING CONTINUED)
WIRING CONNECTIONS
FOR HEATING JUMPERS Y1 to Y2 Blower speed is controlled

SEE HEATING SECTION and by the DC signal from
ABOVE O to R CCB1. Blower operates on
Remove the low speed during
CCB1 with Single-Speed factory−wired dehumidification.
Compressor, no Harmony jumper Otherwise, blower operates
Y1 to DS. on high speed during
cooling cycle.
CCB1 with Two-Speed O to R

Page 94
Compressor, no Harmony Remove jumper Y

See table 9. 1
from Y1 to DS
and
Y1 to Y2.
Y
2

GHR32V−4 OPERATION SEQUENCE AND JUMPERS SUMMARY WITH VSP3−1 (COOLING CONTINUED)
MATCH UP T−STRIP JUMPER COMMENTS OR SEQUENCE WIRING
CONNECTIONS
Remove the wire from Pin #2 and
Pin #13 of the J49 harness connec-
FOR HEATING JUMPERS Y1 to Y2 tor at the motor and the wire from
SEE SEE HEATING SECTION and Pin #3 of the J73 harness connec-
ABOVE O to R tor on the VSP control board.
(Remove Insulate the wire ends and secure
Harmony and jumper from them to prevent shorting. Blower
Single-Speed operates on PWM signal generated
Compressor Y1 to DS.) by the Harmony control board con-
trol board. The Harmony control
board overrides blower speed taps.
Blower speed varies according to
the zone’s demand.
Remove the wire from Pin #2 and Pin

#13 of the J49 harness connector at
the motor and the wire from Pin #3 of
Page 95
the J73 harness connector on the

O to R
VSP control board.
Harmony and (Remove jumper
Insulate the wire ends and secure
Two-Speed Compressor from Y1 to DS
them to prevent shorting. Blower op-
and Y1 to Y2.)
erates on PWM signal generated by
the Harmony control board.
The Harmony control board overrides
blower speed taps. Blower speed
varies according to zone’s demand.
Table 37
GHR32V−5 Units Field Wiring Applications
Jumper Settings (See figure 21)
Thermostat Term. Strip Wiring Connections
E20 W914 W951
Y1 to Y2
1 Heat / 1 Cool SINGLE Yes Intact Intact S1 CONTROL OUTDOOR
T’STAT TERM. STRIP UNIT
NOTE − Use dip
switch 3 to set
second−stage
heat ON delay.
ON−10 minutes.
OFF−15 min-
utes.
1 Heat / 1 Cool SINGLE Yes Cut Intact S1 CCB1 CONTROL OUTDOOR

with CCB1 T’STAT TERM. STRIP UNIT
NOTE − Use dip

switch 3 to set
second−stage
heat ON delay.
ON−10 minutes.
OFF−15 min-
utes.
Page 96
Table 37
GHR32V−5 Units Field Wiring Applications (Continued)
E20 W914 W951
Y1 to Y2
1 Heat / 2 Cool SINGLE No Intact Intact S1 CONTROL OUTDOOR
NOTE − Use dip
switch 3 to set
second−stage
heat ON delay.
ON−10 minutes.
OFF−15 min-
utes.
1 Heat / 2 Cool SINGLE No Cut Intact S1 CCB1 CONTROL OUTDOOR

NOTE − Use dip

switch 3 to set
second−stage
heat ON delay.
ON−10 minutes.
OFF−15 min-
utes.
2 Heat / 2 Cool TWO No Intact Intact S1 CONTROL OUTDOOR

2 Heat / 2 Cool TWO No Cut Intact S1 CCB1 CONTROL OUTDOOR

Page 97
Table 37
GHR32V−5 Units Field Wiring Applications (Continued)

E20 W914 W951
Y1 to Y2
2 Heat / 1 Cool TWO Yes Intact Intact S1 CONTROL OUTDOOR
FM21 Heat SINGLE Yes Intact Cut CONTROL FM21

Pump / 1 Cool TERM. STRIP
*Disconnect existing
furnace transformer
and replace with 75VA,
24V transformer if de-
frost option to be used.
75VA, 24V
TRANSFORMER*
NOTE − Wiring connec- NOTE −
tions to outdoor unit and Remove
thermostat made at Y1/Y2 jumper
FM21 control board per for two−stage
FM21 instructions. cooling.
Harmony TWO Yes Cut Intact TEMP. HARMONY CONTROL OUT-

MOD. TERM. DOOR
Application* SWITCH STRIP UNIT
2 Heat / 1 Cool
FAN LO
FAN LINE
Harmony TWO No Cut Intact TEMP. HARMONY CONTROL OUT-

MOD. TERM. DOOR
Application* SWITCH STRIP UNIT
2 Heat / 2 Cool
FAN LO
FAN LINE
*Cut wires at pin positions 2 and 13 of J/P46. Insulate ends to prevent a short. Blower operates on PWM signal generated by Harmony. Harmony
overrides blower speed taps. Blower speed varies according to zone demand. Low and high−fire controlled by temperature modulating switch.
Page 98
SERVICE NOTES
Page 99

GHR32QV

Uploaded by

Copyright:

Available Formats

GHR32QV

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GHR32QV

Uploaded by

Copyright:

Available Formats

GHR32Q/V

This manual contains information pertaining to

IV Heating System Service Checks . . . . . . . . . . . . . . 47 VIII Operating Flow Charts . . . . . . . . . . . . . . . . . . . . . . 65

Page 1 © 2000 Lennox Industries Inc.

Manifold Pressure (outlet) in. w.g. (kPa)

GHR32Q3-75 BLOWER PERFORMANCE

GHR32Q4/5-100 BLOWER PERFORMANCE

GHR32Q4/5-120 BLOWER PERFORMANCE

High Fire 72,000 (21.1) 100,000 (29.3)

High Fire 67,000 (19.6) 93,000 (27.2)

A.F.U.E. 90.0% 90.0%

California Seasonal Efficiency 83.9 85.3

Exhaust pipe connection (PVC) diameter in. (mm) 2 (51)

Intake pipe connection (PVC) diameter in. (mm) 2 (51)

Condensate drain connection (PVC) in. (mm) 1/2 (12.7)

High Fire 40 − 70 (22 − 39)

High static certified by (A.G.A./C.G.A.) in wg. (Pa) .80 (200)

Gas Piping Size I.P.S. in. (mm) 1/2 (12.7)

Blower motor output hp (W) 1/2 (373) 1 (746)

Tons 2 to 3.5 3.5 to 5

Shipping weight lbs. (kg) 1 package 160 (73) 201 (91)

Electrical characteristics 120 volts 60 hertz 1 phase (less than 12 amps)

Optional Accessories (Must Be Ordered Extra)

Down-Flow Additive Base 32K52 32K53

Roof For 2 inch (51 mm) venting 15F75

Blower Speed Adjustment Settings (Switches 7 and 8)

GHR32V5−100/125−5 Blower Motor Performance

Blower Speed Adjustment Settings (Switches 7 and 8)

CONTROL TRANSFORMER CABINET

CONTROL BOX COVER

A−Make-Up Box (Figure 2) FIGURE 3

A field make−up box (see figure 2) is provided for line voltage

5/16" PIN # FUNCTION

TOP VIEW 3 Roll Out Switch Out

FIGURE 8 4 Gas Valve 24V

LED #1 LED #2 DESCRIPTION

SLOW FLASH OFF Flame sensed without gas valve energized.

NOTE−The mode of operation jumper on the two−stage

While in the single−stage thermostat mode (one−stage

SureLight Control Ignition Sequence Board 56L8301

ÉÉ ON Trial for Blower On"

VSP2−1 VARIABLE SPEED CONTROL BOARD SELECTIONS

than attempting to measure the output voltage of the 1 1 TEST 1

1 2 DS2 ON/OFF DS1 CFM

Diagnostic LED Lights

If HEAT LED−DS2 is on, the blower is running in the heat J46

according to the jumper settings. The light flashes once

need is selected by moving jumper pins. FIGURE 16

VSP3−1 VARIABLE SPEED CONTROL BOARD SELECTIONS

J46 24 VAC half wave rectified (DC pulse), when

1 2 DS2 ON/OFF DS1 CFM Diagnostic LED Lights

VOLTAGES INTO VSP3−1

Voltage across J73 pins 4 to 1 is approximately 15-20VDC (straight voltage)

VOLTAGES FROM VSP3−1 TO ELECTRONICALLY

GHR32V3−75 4 4 NORM 3 #2 PIN JUMPERED

The ADJUST pins allow the motor to run at normal speed

Operating Sequence System Demand System Response

Call for humidity Change to slightly 55% of

DS1 DS2 DESCRIPTION

7−1/2 MIN 100% 7 1/2 MIN 100%

Exhaust pipe connection (PVC) diameter in. (mm) 2 (51)

Intake pipe connection (PVC) diameter in. (mm) 2 (51)