Concure Ab

Concure AB constructive solutions
Acrylic based curing compound
Uses
As a spray applied membrane for interior application on If spray equipment is not available, Concure AB can be
renders or concrete surfaces. Particularly suitable for applied with a soft brush, broom or wide roller. Application
situations where after trades, such as paints or renders, are in this manner should only be made once the concrete has
to be applied. hardened sufficiently to not be damaged during application.
Advantages Application to hardened concrete
Concure AB may also be applied to the surface of newly

■ Improved curing of concrete, enhances cement hydration hardened concrete immediately after de-moulding.
and provides a more durable concrete. Surfaces should be free of stains, oils or form coating which
may otherwise prevent adhesion of Concure AB to the
■ Control of moisture loss improves surface quality, concrete.
reducing permeability, producing a hard wearing, dust
free surface and minimising potential for surface
Coverage rate
cracking and shrinkage.
■ Compatible wit many after trade applications. The recommended coverage rate for Concure AB is
2 2
between 4.0 and 6.0 m /litre (0.25 to 1.6 litres/m ).
■ Easy application reduces labour costs. Coverage rates outside this recommended range may be
used if necessary and suitable to meet specific
Description requirements. Contact the Fosroc Technical Service
Department for advice in such cases.
Concure AB is an acrylic resin based curing compound.
When first applied to a fresh cementitious surface the product Equipment
forms a continuous non-penetrating coating. This coating
dries to form a continuous film which provides a barrier to Spray equipment producing a fine mist may be used for
moisture loss ensuring more efficient cement hydration, Concure AB, such as knapsack or motorised sprayers. The
improved durability and reduced shrinkage. suitability of equipment should be ensured by an application
trial.
Technical support Equipment cleaning
Fosroc provides a technical advisory service for on-site Spray equipment should be cleaned immediately after use
assistance and advice on admixture selection, evaluation by flushing through with white spirit.
trials and dispensing equipment. Technical data and
guidance can be provided for admixtures and other products Over-coating and after-trades
for use with fresh and hardened concrete.
Concure AB is compatible with many after-trades. Contact
Instructions for use the Fosroc Technical Service Department for advice in
specific cases. In all cases it is recommended that small
Application to fresh concrete trial areas are used to ensure that the desired properties are
obtained. Before over-coating, ensure that the Concure AB
Concure AB should be spray applied to the surface of fresh surface is completely free of stains, oils and other materials
concrete. Application should be made approximately 30 that may interfere with the adhesion of the after-trade.
minutes after evaporation has left the concrete free from
surface water. The spray nozzle should be held Limitations
approximately 450 mm from the concrete surface and passed
back and forth to ensure complete coverage. Pump pressure Specifications for high efficiency curing membranes can be
should be maintained to give an even, fine spray. met using Concure A, Concure 90 and Concure WB.
After application, no further application of water or other

Estimating
material is necessary to ensure continued curing. The
concrete surface should not be disturbed until it has sufficient
strength to bear surface loads. The applied film should not Recommended coverage rate is between 4.0 and 6.0
2
be waked on before it is fully dry and care should be taken to m /litre.
ensure that the film is not broken.
Page 1
Concure AB
Packaging Fire
Concure AB is available in drum supply. Details of specific Concure AB is flammable. Do not expose to naked flames
packaging volumes are available on request. or other sources of ignition.
o
Flash point: 38 C
Storage
o
Store Concure AB at temperatures between 4 C and 35 C in
o Cleaning and disposal
unopened original containers. Freezing or prolonged
exposure to direct hear or direct sunlight must also be Spillages of Concure AB should be absorbed onto sand,
avoided. Storage outside these guidelines may impair shelf earth or vermiculate and transferred to suitable containers.
life. Do not use if evaporated, thickened or discoloured. The disposal of excess of waste material should be carried
out in accordance with local legislation under the guidance
Shelf life of the local waste regulatory authority.
12 months when stored in original unopened containers Additional information

under normal warehouse condition.
A range of resin-based high efficiency Concure grades are
Precautions available to meet specific curing requirements. There is
also a range of permanent curing compounds which will
Health and safety accept direct application of paints and other surface finishes
- these include Concure A, Concure 90, Concure WB,
Concure AB should not be swallowed or allowed to come into Concure CR and Concure P.
contact with skin and eyes. Avoid inhalation of vapours and
ensure adequate ventilation. Suitable protective gloves and
goggles should be worn. Some people are sensitive to resins
and solvents. Barrier creams such as Kerodex Anti-solvent
or Rozalex Anti-paint provide additional skin protection.
Should accidental skin contact occur remove immediately
with a resin removing cream such as Kerocleanse Standard
Grade Skin Cleanser or Rozaclens Industrial Skin Cleanser,
followed by washing with soap and water. Do not use
solvent. If Concure AB comes into contact with eyes rinse
immediately with plenty of clean water and seek medical
advice. If swallowed seek medical attention immediately - Do
not induce vomiting.
For further information consult the Material Safety Data sheet

available for this product.
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous
control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products,
whether or not in accordance with any advice, specification, recommendation of information given by it.
Fosam Company Limited

Head Office Telephone: +966 2 637 5345 Fax: +966 2 637 5891 email: fosam@fosroc.com
Post Box 11081 Regional Offices
Jeddah – 21453 Jeddah Sales Office Tel: (02) 608 0999 Fax: (02) 638 0693 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Saudi Arabia Jeddah Showroom Tel: (02) 665 0187 Fax: (02) 667 4844 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Riyadh Tel: (01) 482 9303 Fax: (01) 482 7562 Medinah Tel: (04) 855 0091 Fax: (04) 855 0047
Dammam Tel: (03) 814 1282 Fax: (03) 814 1581 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875
www.fosroc.com Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2 FO SA/CONCURE AB/01/05

Concure Ab

Uploaded by

Copyright:

Available Formats

Concure Ab

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Concure Ab

Uploaded by

Copyright:

Available Formats

Concure AB constructive solutions

Acrylic based curing compound

Advantages Application to hardened concrete

Concure AB may also be applied to the surface of newly

After application, no further application of water or other

12 months when stored in original unopened containers Additional information

For further information consult the Material Safety Data sheet

Fosam Company Limited

You might also like