Inverter and Its Topologies

1.
2 INVERTER AND IT’S TOPOLOGIES
Various topologies and modulation strategies of multilevel inverters

have been proposed.
1.2.1 INVERTER
A dc-to-ac converter whose output is of desired output voltage and

frequency is called an inverter.
Based on their operation the inverters can be broadly classified into
 Voltage Source Inverters(VSI)
 Current Source Inverters(CSI)
A voltage source inverter is one where the independently controlled ac

output is a voltage waveform.
A current source inverter is one where the independently controlled ac
output is a current waveform.
On the basis of connections of semiconductor devices, inverters are
classified as
 Bridge inverters
 Series inverters
 Parallel inverters
Some industrial applications of inverters are for adjustable- speed ac

drives, induction heating, stand by air-craft power supplies,
UPS(uninterruptible power supplies) for computers, hvdc transmission
lines etc.
The inverters which produce which produce an output voltage or a
current with levels either 0 or +-V are known as two level inverters. In
high-power and high-voltage applications these two-level inverters
however have some limitations in operating at high frequency mainly due
to switching losses and constraints of device rating. This is where

multilevel inverters are advantageous.
Increasing the number of voltage levels in the inverter without requiring
higher rating on individual devices can increase power rating. The unique
structure of multilevel voltage source inverters’ allows them to reach
high voltages with low harmonics without the use of transformers or
series-connected synchronized-switching devices.
FIG1.1 Ideal five level inverter output voltage(V inv )
The harmonic content of the output voltage waveform decreases

significantly. Ac loads require constant or adjustable voltages at their
input terminals. When such loads are fed by inverters, it’s essential that
output voltage of the inverters is so controlled as to fulfill the
requirements of AC loads. This involves coping with the variation of DC
input voltage, for voltage regulation of inverters and for the constant
volts/frequency control requirement. There are various techniques to vary
the inverter gain. The most efficient method of controlling the gain (and
output voltage) is to incorporate pulse-width modulation (PWM) control
within the inverters.
The carrier based PWM schemes used for multilevel inverters is one of
the most straight forward methods of describing voltage source
modulation realized by the intersection of a modulating signal (Duty
Cycle) with triangular carrier wavefroms.
Cascaded H-bridge Multilevel Inverter has been receiving wide attention
due to its numerous advantages as a dc/ac interface. The advantages are
 Requires the least number of components compare to other
multilevel inverters.
 Each inverter is in modular layout. Therefore able to add-on or
replaced when necessary.
 Can generate almost sinusoidal waveform voltage while only
switching one time per fundamental cycle.
 Able to make direct parallel or series connection to medium and
high voltage power system without any transformer.
 High efficiency due to minimum switching frequency.
 Eliminate the use of transformer.
FIG.1.2 Cascaded H-bridge Multilevel Inverter
1.2.2 Investigation on Inverter Topologies
Multilevel voltage source converters are emerging as a new breed of

power converter options for high-power applications. The multilevel
voltage source converters typically synthesize the staircase voltage wave
from several levels of dc voltages. There are some multilevel voltage
source converters which are
1) diode-clamp,
2) flying capacitors, and
3) cascaded-inverters with separate dc sources.
In this section, Conventional Inverter and different multilevel converters

topologies shall be discuss.
Conventional Inverter
1) Half-Bridge Inverter
As shown in Fig 1.3, half-bridge inverter consists of 2 switches, 2 diodes

and 2 dc sources. This inverter works where SW1 is ‘ON’, SW2 is ‘OFF’
and vice-versa. +V dc /2 is generated at the output when SW1 is ‘ON’, SW2
is ‘OFF’ and –V dc /2 is generated when SW1 is ‘OFF’, SW2 is ‘ON’.
FIG.1.3 Half- bridge Inverter
2) Full-Bridge Inverter
As shown in Fig 1.4, full-bridge inverter consists of 4 switches, 4 diodes

and 2 dc sources. It operates in two modes.
FIG.1.4. Full-bridge inverter
First mode of operation, +Vdc is generated when SW1 & SW4 are ‘ON’
and –Vdc is generated when SW2 & SW3 are ‘OFF’.
Second mode of operation, 0V is generated when SW1 & SW2 or SW3 &
SW4 are ‘ON’. This mode of operation is the fundamental building block
for Cascaded H-bridge multilevel inverter. Fig 1.5 & Fig 1.6 shows the
output voltage for the first and second mode of operation.
FIG.1.5 First mode FIG.1.6 second mode

MULTILEVEL INVERTER TOPOLOGIES :
1) Diode-Clamp Multilevel Converters

Basic Principle:
An m-level diode-clamp converter typically consists of m – 1
capacitors on the dc bus and produces m levels of the phase voltage.
Fig.1.7 shows a single-phase full bridge five-level diode-clamp
converter in which the dc bus consists of four capacitors, C 1 , C 2 , C 3
and C 4 . For a dc bus voltage V dc , the voltage across each capacitor is
V dc /4 and each device voltage stress will be limited to one capacitor
voltage level, V dc /4, through clamping diodes.
FIG.1.7
Table 1.1 lists the voltage levels and their corresponding switch states.
State 1= ‘ON’ and State 0=’OFF’.
Table 1.1
Fig. 1.8 shows phase and line voltage waveforms of the 5-level converter.
The resulting line voltage is a 9-level staircase wave. This implies that an
m-level converter has an m-level output phase voltage and a (2m-1)-level
output line voltage.
Fig. 1.8 Phase and line voltage waveform of a 5-level diode-clamp
voltage source converter
Fig.1.8 Phase and line voltage waveform of a 5-level diode-clamp voltage

source converter
The clamping diodes need to have different voltage ratings for reverse
voltage blocking. Assuming that each blocking diode voltage rating is the
same as the active device voltage rating, the numbers of diodes required
for each phase will be (m-1) X (m-2). This equation shows a quadratic
increase in m. If m is high, the number of diodes required will be
impractical to implement.
Advantages of a diode-clamp multilevel voltage source converter
 When the number of levels is high enough, harmonic content will
be low enough to avoid the need for filters.
 Efficiency is high because all devices are switched at the
fundamental frequency.
 Reactive power flow can be controlled.
 The control method is simple for a back-to-back intertie system.
 Disadvantages of a diode-clamp multilevel voltage source converter
 Excessive clamping diodes are required when the number of levels
is high.
2) Flying-Capacitors Multilevel Converters
The voltage level defined in the flying-capacitor converter is similar to

that of the diode-clamp type converter. The phase voltage of an m-level
converter has m levels including the reference level, and the line voltage
has (2m-1) levels.
The working principle is based on charging each capacitor to a different
voltage level. The different in the magnitude of the voltage level between
two capacitors will regulate the size of the output voltage at the terminal.
Fig.1.9 shows the single-phase full-bridge flying-capacitor based 5-level
converter.
FIG.1.9 A flying-capacitor based 5-level converter circuit diagram
Table1.2 lists the voltage levels and their corresponding switch states.
Table1.2
Large number of storage capacitors is required. An m-level converter

require a total of (m-1) x (m-2)/2 auxiliary capacitors per phase leg in
addition to (m-1) main dc bus capacitors.
Advantages of a flying-capacitor multilevel voltage source converter:
1
 Large amount of storage capacitors provides extra ride through
capabilities during power outage.
 Provides switch combination redundancy for balancing different
voltage levels.
 When the number of levels is high enough, harmonic content will
be low enough to avoid the need for filters.
 Both real and reactive power flow can be controlled.
 Disadvantages of a flying-capacitor multilevel voltage source
converter
 An excessive number of storage capacitors are required when the
number of converter levels is high.
Disadvantages:
The inverter control will be very complicated, and the switching
frequency and switching losses will be high for real power transmission.
3) Cascaded H-bridges Multilevel Converters
A cascaded multilevel inverter consists of a series of H-bridge (single-

phase full-bridge) inverter units. The general function of this multilevel
inverter is to synthesize a desired voltage from several separate dc
sources, which may obtain from batteries, fuel cells, or solar cells.
Fig. 1.10 shows a single-phase structure of a cascade inverter with
separate dc sources. Each separate dc source is connected to a single-
phase full-bridge inverter. Each inverter level can generate three different
voltage outputs, +Vdc, 0, and –Vdc.
FIG.1.10 a multilevel cascaded H-bridges inverter
The ac outputs of the inverters are connected in series such that the
synthesized voltage waveform is the sum of the inverters outputs. The
output phase voltage levels is defined by m = 2s+1, s = no. of dc sources.
Cascaded H-bridge Multilevel Inverter has been receiving wide attention

due to its numerous advantages as a dc/ac interface. The advantages are :
 Requires the least number of components compare to other
multilevel inverters.
 Each inverter is in modular layout. Therefore able to add-on or
replaced when necessary.
 Can generate almost sinusoidal waveform voltage while only
switching one time per fundamental cycle.
 Able to make direct parallel or series connection to medium and
high voltage power system without any transformer.
 High efficiency due to minimum switching frequency.
Comparison of the Topologies
Diode-Clamp Multilevel Inverters, Flying-Capacitors Multilevel Inverters

and Cascaded H-bridges Multilevel Inverters are all suitable to be used as
an interface in Photovoltaic application, due to the modular structure of
PV arrays, to generate different DC voltage levels. Two main concerns in
selecting a suitable inverter for the project are the components count
used and the switching algorithm on the inverter topologies.
For Diode-clamped multilevel Inverter and Flying-Capacitors Multilevel
Inverter, the number of semiconductor devices used for the circuit is very
high. Both inverters devices count is greater than Cascaded H-bridges
Multilevel Inverter. Therefore, the Cascaded H-bridges Multilevel
Inverter is the most cost-effective.
Diode-clamped multilevel Inverter, the charging time for each capacitor
is different, such a capacitor charging profile repeats every half cycle,
this result in un-balanced capacitor voltage between different levels.
Though it can be solved by complicated control algorithm, this will result
in system complexity and cost penalties. For Flying-Capacitors
Multilevel Inverter, when it involves real power conversions, the
selection of a switch combination becomes very complicated in order to
balance the capacitor charge and discharge. Each capacitor must be
charged with different voltages as the voltage level increase.
Cascaded H-bridges Multilevel Inverter is the focus of this project due to
its components required is the least to achieve the same number of
voltage levels. The circuit layout is in modular structure, which means a
faulty module can be replaced with another module without affecting the
rest of the circuit. Whenever there’s a need to increase the output
voltage, additional modules can be added. This means lower maintenance
cost too

Inverter and Its Topologies

Uploaded by

Copyright:

Available Formats

Inverter and Its Topologies

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Inverter and Its Topologies

Uploaded by

Copyright:

Available Formats

1.

2 INVERTER AND IT’S TOPOLOGIES

Various topologies and modulation strategies of multilevel inverters

A dc-to-ac converter whose output is of desired output voltage and

 Current Source Inverters(CSI)

A voltage source inverter is one where the independently controlled ac

Some industrial applications of inverters are for adjustable- speed ac

to switching losses and constraints of device rating. This is where

FIG1.1 Ideal five level inverter output voltage(V inv )

The harmonic content of the output voltage waveform decreases

1.2.2 Investigation on Inverter Topologies

Multilevel voltage source converters are emerging as a new breed of

In this section, Conventional Inverter and different multilevel converters

As shown in Fig 1.3, half-bridge inverter consists of 2 switches, 2 diodes

FIG.1.3 Half- bridge Inverter

As shown in Fig 1.4, full-bridge inverter consists of 4 switches, 4 diodes

FIG.1.5 First mode FIG.1.6 second mode

1) Diode-Clamp Multilevel Converters

Fig.1.8 Phase and line voltage waveform of a 5-level diode-clamp voltage

The voltage level defined in the flying-capacitor converter is similar to

Large number of storage capacitors is required. An m-level converter

3) Cascaded H-bridges Multilevel Converters

A cascaded multilevel inverter consists of a series of H-bridge (single-

Cascaded H-bridge Multilevel Inverter has been receiving wide attention

Comparison of the Topologies

Diode-Clamp Multilevel Inverters, Flying-Capacitors Multilevel Inverters

You might also like