AircraftDesign 8 HighLift
AircraftDesign 8 HighLift
AircraftDesign 8 HighLift
Subsection 8.2 deals with the approximate calculation of the maximum lift coefficients from
the geometrical parameters, which are assumed to be known, of the high lift systems.
Subsection 8.3 shows how this analytical method of calculation can be inverted for the design
of the high lift system. It is demonstrated how the characteristic geometrical parameters for
describing the high lift system can be calculated from the lift coefficients for take-off and
landing selected in Section 5.
In the history of aircraft development every conceivable alternative has been put to the test to
increase lift. Fig. 5.4, Fig. 8.1 and Fig. 8.3 only describe the versions that have established
themselves in practice.
8-2
Fig. 8.1 Different trailing edge high lift systems (airfoils from DATCOM 1978)
Split flaps are no longer used because they produce more drag than a plain flap with the same
increase in lift.
The slotted flap gets its name from the slot between the wing and the flap. Air can flow from
the bottom to the top of the airfoil through the specially shaped slot. This high-energy flow
produces a new boundary layer on the top surface of the flap, which allows flap angles of up
to 40° without separating the flow. Consequently maximum lift is increased and drag is
reduced by the slot.
Fowler flaps have a slot between the wing and flap like slotted flaps.
• Fowler flaps are first extended to the rear, thus increasing the wing area. With increasing
wing area the lift becomes greater. If the reference area S ref is now kept constant in the lift
equation L = 1 / 2 ρ v 2 ⋅ C L ⋅ S ref , the lift coefficient increases (by definition). By moving
8-3
the Fowler flap downwards, the lift is increased without a disproportionate increase in drag.
The corresponding flap position is therefore especially suited to take-off.
• If the Fowler flap is further extended, the flap body is also turned downwards, which now
increases the airfoil camber. The lift continues to increase, but now with a greater increase
in drag. The corresponding flap position is therefore suitable for landing.
In the case of all high lift mechanisms it must be borne in mind that the flap mountings have
to be housed in fairings. The fairings represent an additional drag throughout the entire flight,
which can compromise the advantages of the high lift system.
To further improve the flow over the flap, double slotted flaps or even triple slotted flaps
can be used.
A leading edge flap increases the curvature of the top of the airfoil. This considerably
increases the lift coefficient.
8-4
A movable slat (slotted leading edge flap) increases the lift through a combination of
increased wing area and increased camber and through the influence of the flow with the aid
of the slat.
A Kruger flap forces the flow to run more over the top of the airfoil. Kruger flaps can be
built more easily and made more lightweight than slats, but the disadvantage is their high level
of drag at small angles of attack. In the case of large passenger aircraft Kruger flaps are often
used on the inner wing together with slats on the outer wing.
Fig. 8.3 Different leading edge high lift systems (airfoils from DATCOM 1978)
To sum up, it can be stated that effective high lift systems have a more complicated design
than simple and less effective systems, and this leads to higher acquisition and maintenance
costs. On the other hand, the more effective system saves fuel through the possibility of
building a lighter wing with better lift-to-drag ratio than would be possible in the case of an
overall design with a simple high lift system. An optimum compromise can – as is so often the
case – only be found through detailed studies. In the early stages of design it is therefore
advisable to follow the designs of successful aircraft models.
Fig. 8.4 shows a typical lift curve cL = f ( α ) . α is the angle of attack, which is defined as the
angle between the free – i.e. undisturbed – flow direction and the chord line of the airfoil
without a flap deflection. With an angle of attack of 0° the uncambered airfoil does not show
any lift. The cambered airfoil, on the other hand, already has a certain lift coefficient with an
angle of attack of α = 0 , and also achieves a higher maximum lift coefficient. The zero-lift
angle of attack α 0 is negative in the case of an airfoil with a positive camber. The lift curve
slope cLα is constant apart from a small section just before the stall angle α cL , max .
If, exceptionally, no wind tunnel data or airfoil catalogs are available, it is possible to estimate
the maximum lift coefficient according to DATCOM 1978 (4.1.1.4):
∆ 1c L,max Correction term for taking into account the airfoil camber and the position of
maximum camber. Position of maximum thickness: 30%.
∆ 2 c L ,max Correction term for taking into account a position of maximum thickness ≠ 30%
∆ 3c L ,max Correction term for taking into account the influence of Reynolds'
number ≠ 9 . 106.
Additional corrections would be necessary to take into account the roughness of the airfoil
surface and the Mach number. However, these corrections cannot be stated with universal
validity.
The maximum lift coefficient of a wing depends on the leading-edge sharpness parameter
∆y , which is defined in Fig. 8.5:
• in the case of a sharp airfoil leading edge (i.e. small ∆y ) the flow starts to separate at the
airfoil leading edge.
• in the case of a more rounded airfoil leading edge (i.e. large ∆y ) the flow starts to separate
at the airfoil trailing edge.
8-7
In the case of known NACA airfoils, ∆y can be directly determined from the maximum
relative thickness with the aid of Table 8.1.
Table 8.1: ∆y -parameter for known NACA airfoils determined from DATCOM 1978 (2.2.1-8)
Airfoil type ∆y
NACA 4 digit 26.0 ⋅ ( t / c)
NACA 5 digit 26.0 ⋅ ( t / c)
NACA 63 series 22.0 ⋅ ( t / c)
NACA 64 series 21.3 ⋅ ( t / c)
NACA 65 series 19.3 ⋅ ( t / c)
NACA 66 series 18.3 ⋅ ( t / c)
Fig. 8.6 Maximum lift coefficient of a symmetrical airfoil at a Reynolds' number of 9 ⋅ 106 as a
function of ∆y and the position of maximum thickness
8-8
Fig. 8.7 Correction term ∆ 1c L,max to calculate the maximum lift coefficient of an airfoil accord-
ing to DATCOM 1978. Considered are airfoil camber and position of maximum cam-
ber.
8-9
Fig. 8.8 Correction terms to calculate the maximum lift coefficient of an airfoil according to
DATCOM 1978.
Above: Figure 8.7 continued
Middle: ∆ 2 c L ,ma x : Correction term for the position of maximum thickness
Below: ∆ 3 c L,ma x : Correction term for the influence of Reynolds' number
8 - 10
On the other hand, many of the airfoils used in commercial aircraft have a more rounded
airfoil leading edge (i.e. a large ∆y ). This is the case, for example, on supercritical airfoils
(compare Section 7) or on airfoils with a larger relative thickness. In such cases flow
separation occurs, starting at the airfoil trailing edge, and the maximum lift coefficient of the
swept wing decreases compared to an unswept wing. This effect has already been expressed
approximately in Section 7 by
The maximum lift coefficient with retracted flaps is estimated here according to
DATCOM 1978 (4.1.3.4 Method 2). This is an empirical method that may be applied in the
subsonic range to untwisted tapered wings with a constant airfoil section over the span. The
following must apply for the aspect ratio:
8
A> . (8.2)
3 ⋅ cos ϕ 25
According to DATCOM 1978 it is:
C L ,max
C L,max,clean = ⋅ c L ,max ,clean + ∆ C L,max . (8.3)
c
L,max
This includes
CL ,max
stated in Fig. 8.9.
c L,max
c L,max the maximum lift coefficient of the airfoil. c L,max is taken from measurements or
airfoil catalogs. If, exceptionally, no measurements or airfoil catalog are available,
equation (8.1) can be referred to.
∆ CL,max Mach number correction term from Fig. 8.10. For Mach numbers smaller than 0.2
∆y leading-edge sharpness parameter as described above.
8 - 11
Fig. 8.9 Maximum lift of tapered wings with a high aspect ratio in subsonic speeds.
Λ LE stands for sweep angle of the leading edge ϕ LE (DATCOM 1978)
8 - 12
Fig. 8.10 Correction term ∆ CL,max to calculate the maximum lift of tapered wings with a high
aspect ratio in subsonic speeds. Λ LE stands for sweep angle of the leading edge ϕ LE
(DATCOM 1978). For Mach numbers smaller than 0.2 ∆ CL ,max = 0.
8 - 13
( ∆c L ,max ) base is the maximum increase in the lift coefficient for a flap with a 25% flap
chord according to Fig. 8.11 at a reference flap angle (according to Fig.
8.13).
k1 is a factor according to Fig. 8.12, which takes into account a relative flap
chord that has a value other than 25%.
k2 is a factor according to Fig. 8.13, which takes into account a flap deflection
that differs from the reference value according to Fig. 8.13.
k3 is a factor according to Fig. 8.14, which takes into account the flap
kinematics (Fig. 8.2).
The increase in the lift coefficient of the airfoil through slats or flaps on the airfoil leading
edge can also be determined. The method cannot be applied to Kruger flaps; leading edge
flaps can be calculated up to a deflection of 30° and slats up to a deflection of 20°. Above 20°
an excessively high increase in the lift coefficient is calculated. It is
c'
∆c L,max ,s = cl ,δ ,max η max ηδ δ f . (8.5)
c
Fig. 8.11 Maximum increase in lift coefficient for 25%-chord flaps at a reference flap angle (ac-
cording to Figure 8.13) (DATCOM 1978)
Fig. 8.12 Factor that takes the relative flap-chord into account, which has
a different value then 25% (DATCOM 1978)
8 - 15
Fig. 8.13 Factor that takes the flap angle into account,
which differ from the reference value
(marked by • in the figure) (DATCOM 1978)
Fig. 8.14 Factor that takes the flap kinematics (see Fig. 8.2)
into account (DATCOM 1978)
8 - 16
Fig. 8.17 Empirical factor that takes the real deflection angle in contrast to the optimum deflec-
tion angle (reference angle) into account (DATCOM 1978)
Fig. 8.18 Geometrical definitions of an airfoil with slat (adapted from DATCOM 1978). The airfoil
chord line is defined with retracted slat. The slat is extended and rotated downwards.
The slat deflection angle may be determined from the deflected airfoil chord line which
is defined by the leading edge and the c'/2-point on the airfoil chord line.
8 - 18
Increase in the maximum lift coefficient of a wing through high lift devices
For flaps the calculation is carried out according to DATCOM 1978 (6.1.4.3)
SW , f
∆C L,max,f = ∆c L ,max,f ⋅ ⋅ KΛ . (8.6)
SW
∆c L ,max,f Increase in the maximum lift coefficient of the airfoil produced by flaps.
KΛ an empirical correction factor according to Fig. 8.19 for taking into account the
wing sweep ϕ 25 .
SW , f
Area ratio for the flaps according to Fig. 8.20.
SW
For slats an estimate according to Raymer 1992 is selected because DATCOM 1978 does not
contain a generally applicable method.
SW ,s
∆C L,max,s = ∆c L,max,s ⋅ ⋅ cos ϕ H . L. . (8.7)
SW
∆c L ,max,s Increase in the maximum lift coefficient of the airfoil produced by slats.
SW ,s
Area ratio for the slats. Calculation according to Fig. 8.20, only that in this case
SW
the hatching indicates the area that lies behind the slats.
ϕ H .L. Sweep angle of the hinge line of the slats.
Fig. 8.19 Correction factor that takes the sweep into account Λ c/4 = ϕ 25 (DATCOM 1978)
A simple conservative assumption can be adopted as maximum lift coefficient for the design
of the wing, including the high lift systems:
CL ,max, INITIAL SIZING is the maximum lift coefficients assumed in Section 5 for preliminary sizing
for take-off CL ,max,TO and landing CL,max, L
Factor 1.1 ensures that the aircraft can still stay in the air if the empennage creates
negative lift to trim the aircraft.
The maximum lift coefficient for the wing CL ,max,clean has already been established through the
wing design in Section 7 – by means of the parameters found there – and can be calculated
using the method from Subsection 8.2. On the basis of equation (8.8) the following is
produced
Factor 0.95 takes into account the following interrelationship: the use of landing flaps
creates a moment around the pitch axis. This moment must be compensated
for by using trim. The negative lift created by the trim has to be balanced out
by an additional lift of the wing.
As a result of factors 1.1 and 0.95 according to Roskam II in equation (8.9) and equation
(8.10), the maximum wing lift is greater than CL ,max, INITIAL SIZING . This is necessary for a
balanced sum of forces across the whole aircraft.
The aim of the design is now to determine the parameters of the high lift system in such a way
that in equation (8.10) the left side is somewhat larger than (or at least the same as) the right
side. To do this, the achievable lift must be distributed over the slats and flaps. The spanwise
reach of slats and flaps has to be established, as must the flap type and the angle of deflection
of slats and flaps. As already mentioned in Section 2, it will not generally be possible to set
the parameters without an iterative approach.
8 - 21
The calculation methods used here largely stem from DATCOM 1978. DATCOM (data
compendium) contains so-called handbook methods that produce a result relatively quickly.
DATCOM 1978 is a professional tool and has been repeatedly quoted by a large number of
authors in the field of aircraft design for decades and is used for initial design steps. However,
nowadays the detailed design of an aircraft requires considerably more precise information.
This information can only be obtained by using detailed numerical methods and powerful
computers.