Standart Iso 13314

Abstract of :
ISO 13314 :2011 Mechanical testing of metals — Ductility testing — Compression

test for porous and cellular metals
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13314 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals,
Subcommittee SC 2, Ductility testing.
Introduction
Porous and cellular metals have attractive properties due to their unique cell morphology. When they are
used as a crush energy absorbing component of automotive machines, compressive properties are
necessary for industrial design. However, the deformation behaviour of porous metals and metallic foams
is quite different from conventional dense metals. Test methods for conventional metallic materials are not
suitable for porous metals and metallic foams. Standardization of a test method for porous metals and
metallic foams is required.
1 Scope
This International Standard specifies a test method for compressive properties of porous and cellular
metals with a porosity of 50 % or more. Compressive tests can be carried out at ambient temperature
under quasistatic strain rate conditions.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
 ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1:
Tension/compression testing machines — Verification and calibration of the force-measuring
system
 ISO 9513, Metallic materials — Calibration of extensometers used in uniaxial testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
compressive stress
σ
compressive force divided by the initial cross-sectional area perpendicular to the loading direction
Note 1 to entry: Compressive stress is expressed in newtons per square millimetre.
3.2
compressive strain
e
overall compressive displacement divided by the initial height (gauge length) of the test specimen
Note 1 to entry: Compressive strain is expressed as a percentage.
3.3
first maximum compressive strength
compressive stress corresponding to the first local maximum in the stress-strain curve
SEE: Figure 1
Note 1 to entry: It cannot be determined if no local maximum occurs.
3.4
plateau stress
σpl
arithmetical mean of the stresses at 0,1 % or smaller strain intervals between 20 % and 30 % or 20 % and
40 % compressive strain
SEE: Figure 1
Note 1 to entry: The strain range/interval, 20 % and 30 % or 20 % and 40 %, for arithmetical mean varies
depending on the plateau end strain.
3.5
plateau end
point in the stress-strain curve at which the stress is 1,3 times the plateau stress
SEE: Figure 1
Note 1 to entry: If this point does not adequately represent the end of the plateau range, another stress
can be selected which corresponds to the curve trace (see 7.4).
3.6
energy absorption
W
area under the stress-strain curve up to 50 % strain or up to the plateau end strain, eple
Note 1 to entry: The energy absorption up to other strain values can also be determined (see 7.7).
3.7
energy absorption efficiency
We
energy absorption divided by the product of the maximum compressive stress within the strain range and
the magnitude of the strain range
3.8
quasi-elastic gradient
gradient of the straight line determined within the linear deformation region at the beginning of the
compressive stress-strain curve
Note 1 to entry: This gradient is not a modulus for the material (see Figure 1). The quasi-elastic gradient is
optionally measured and it is used to determine the zero point for the compressive strain [see Figure 2 a)].
3.9
compressive offset stress
compressive stress at the plastic compressive strain of 0,2 %, unless otherwise specified or recorded
Note 1 to entry: The plastic strain is determined using of the quasi-elastic gradient [see Figure 2 a)]. The
compressive 0,2 % offset stress is optionally measured and it can be used as an alternative to the
compressive yield strength.
3.10
elastic gradient
gradient of the elastic straight lines determined by elastic loading and unloading between stresses of σ70
and σ20
Note 1 to entry: σ70 and σ20 correspond to 70 % and 20 %, respectively, of the plateau stress, σpl.
Note 2 to entry: The elastic straight line is the secant line obtained from the hysteresis loop which occurs
during unloading and subsequent loading (see Figure 1). The elastic gradient represents a porosity-
dependent rigidity, not a modulus of the material, and generally changes during the course of
compression. The elastic gradient is optionally measured and it is used to determine the zero point for the
compressive strain [see Figure 2 b)].
3.11
compressive proof strength
compressive stress at a plastic compressive strain of 1,0 %, unless otherwise specified or recorded
Note 1 to entry: The plastic strain is determined using of the elastic gradient [see Figure 2 b)]. The
compressive proof strength is optionally measured and it can be used as an alternative to the compressive
yield strength.
Figure 1 — Stress-strain curve to determine the characteristic values from compression testing of
porous and cellular metals
Key
1 quasi-elastic gradient
2 elastic gradient
3 first maximum compressive strength

Standart Iso 13314

Uploaded by

Copyright:

Available Formats

Standart Iso 13314

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Standart Iso 13314

Uploaded by

Copyright:

Available Formats

Abstract of :

ISO 13314 :2011 Mechanical testing of metals — Ductility testing — Compression

3 Terms and definitions

You might also like