R 1631014112018
R 1631014112018
R 1631014112018
4 The flange of a T beam flange of the beam is 90 cm х 12cm and web below is 30cm х [14M]
40cm. It is reinforced with 4-25 mm plus 4-12mm Fe 415 steel bars in tension at an
effective cover of 50mm. Determine the shear reinforcement needed for a shear force
of 250kN (i) If the mix is M20 and (ii) if the mix is M25. Take load factor = 1.5.
5 Design a square spread footing to carry a column of 1800kN from a 60 cm square tied [14M]
column containing 25mm bars as the longitudinal reinforcement. The bearing capacity
of soil is 180 kN/m2. Consider base of footing as 1m below the ground level. The unit
weight of earth is 20 kN/m3. Use σy = 415 N/mm2 and σck = 20 N/mm2.
1 of 2
|''|'''||''||'''|||| www.manaresults.co.in
Code No: R1631014 R16 SET - 1
6 a) What is the minimum percentage of steel allowed in a RC column. Explain why it is [14M]
necessary to specify the minimum percentage.
b) A column 230 mm х 350 mm is reinforced with 4 bars 20mm one at each corner
effective cover of 50mm. It is loaded with characteristic load = 340 kN. Factored
Moment in the direction of larger dimension Mux = 30 kNm. Factored Moment in the
direction of shorter dimension Muy = 18 kNm. About Y axis bisecting the width.
Assume concrete grade M 20 and steel grade Fe 415 steel. Check the safety of the
column.
*****
2 of 2
|''|'''||''||'''|||| www.manaresults.co.in
Code No: R1631014 R16 SET - 2
4 a) What are the assumptions for the design of a reinforced concrete section for limit [7M]
state of collapse in bending?
b) Show that the limiting depth of neutral axis for a rectangular cross section reinforced [7M]
with FE415 grade steel in 0.48d.
5 An RC beam has an effective depth of 450mm and breadth of 250mm. It contains 4-25mm [14M]
bars mild steel out of which two bars are bent up at 30 degrees near the support in tension.
Calculate the shear resistance of the bent up bars. What additional stirrups are needed if it
has to resist a design shear force of 150 kN. Use M20 mix.
6 Design an isolated square column 400mm х 400mm reinforced with 6 - 20mm [14M]
diameter bars carrying a service load of 1400 kN The bearing capacity of soil is 200
kN/m2 at a depth of 1.5m below ground. The footing is restricted to 2.0m in one
direction Assume M20 grade concrete and Fe 415 grade steel for the footing and
M25 concrete and Fe 415 steel for the column.
1 of 2
|''|'''||''||'''|||| www.manaresults.co.in
Code No: R1631014 R16 SET - 2
7 The section of a cantilever beam designed for a span of 4.0m is having dimensions [14M]
300 х 600mm with 3 numbers 20mm diameter bars in compression and 3 numbers
16mm diameter bars in tension. The beam has been designed for a bending moment
of 170kNm (at support) under service loads, of which 65 percent is due to
permanent (dead) loads. The loading is uniformly distributed on the span. Assume
M20 concrete and Fe 415 steel.
i) Calculate the maximum short-term deflection
ii) The short-term deflection due to live loads alone.
*****
2 of 2
|''|'''||''||'''|||| www.manaresults.co.in
Code No: R1631014 R16 SET - 3
4 An L beam has flange of the beam is 90 cm х 12cm and web below is 23cm х 50cm. Determine [14M]
the area of compression and tension steels needed for the cross section if it is to carry a factored
bending moment of 400 kNm. Assume M20 concrete and TMT 500 grade steel.
5 Design a short circular column 6m long to carry an axial load of 250kN if both ends of the [14M]
column are fully restrained using i) Lateral ties and ii) helical steel
6 An RC beam has an effective depth of 300mm and breadth of 150mm. It contains 4- [14M]
20mm bars. Determine the shear resistance of the concrete beam if σsv = 415 N/mm2 for
i) σck = 20 N/mm2 and ii) σck = 30 N/mm2
7 The section of a cantilever beam designed for a span of 5.0m is having dimensions 300 х [14M]
600mm with 3 numbers 28mm diameter bars in compression and 3 numbers 20mm
diameter bars in tension. The beam has been designed for a bending moment of 200kNm
(at support) under service loads, of which 70 percent is due to permanent (dead) loads.
The loading is uniformly distributed on the span. Assume M20 concrete and Fe 415 steel.
Calculate the maximum short-term deflection.
*****
|''|'''||''||'''|||| www.manaresults.co.in
www.manaresults.co.in
Code No: R1631014 R16 SET - 4
4 An RC beam has an effective depth of 450mm and breadth of 300mm. It contains 5- [14M]
20mm bars mild steel out of which two bars curtailed at a section where shear force
at service load is 100kN. Design the shear reinforcement if the concrete is M20.
5 Design a section of a ring beam 50cm wide and 65cm deep subjected to a bending [14M]
moment of 120kNm, twisting moment of 7.5-kNm and shear force of 150 kN at
ultimate. Use M20 mix and Fe 415 grade steel.
6 Draw axial force moment interaction curve for a rectangular column with 2% steel [14M]
distributed equally on two faces. Assume a minimum of 12 bars placed at an effective cover
of 0.15D.
7 Explain short-term deflection. Explain the difficulty in estimating short term deflection as [14M]
per IS code procedure when applied moment at service loads is marginally less than the
cracking moment Are the nominal detailing requirements of the code adequate for ensuring
crack width control? Comment.
*****
|''|'''||''||'''|||| www.manaresults.co.in
www.manaresults.co.in