Renewable Energy Applications For Existing Buildings: Preprint
Renewable Energy Applications For Existing Buildings: Preprint
Renewable Energy Applications For Existing Buildings: Preprint
Conference Paper
NREL/CP-7A40-52172
August 2011
The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC
(Alliance), a contractor of the US Government under Contract No. DE-AC36-08GO28308. Accordingly, the US
Government and Alliance retain a nonexclusive royalty-free license to publish or reproduce the published form of
this contribution, or allow others to do so, for US Government purposes.
This report was prepared as an account of work sponsored by an agency of the United States government.
Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty,
express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of
any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately
owned rights. Reference herein to any specific commercial product, process, or service by trade name,
trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation,
or favoring by the United States government or any agency thereof. The views and opinions of authors
expressed herein do not necessarily state or reflect those of the United States government or any agency thereof.
P.O. Box 62
Oak Ridge, TN 37831-0062
phone: 865.576.8401
fax: 865.576.5728
email: mailto:reports@adonis.osti.gov
Cover Photos: (left to right) PIX 16416, PIX 17423, PIX 16560, PIX 17613, PIX 17436, PIX 17721
Printed on paper containing at least 50% wastepaper, including 10% post consumer waste.
Renewable Energy Applications for Existing
Buildings
Applicazioni dell’energia rinnovabile su edifici esistenti
SHEILA J. HAYTER, PE, FASHRAE – ALICEN KANDT
U.S. Department of Energy’s National Renewable Energy Laboratory – Integrated Applications Center
SUMMARY
This paper introduces technical opportunities, means, and methods for incorporating renewable
energy technologies into building designs and operations. This paper provides an overview of renewable
energy resources and available technologies used successfully to offset building electrical and thermal
energy loads. Methods for applying these technologies in buildings and the role of building energy
efficiency in successful renewable energy projects are addressed. Tips on implementing effective
renewable energy projects are also provided.
RIASSUNTO
Questa memoria considera le opportunità tecniche, i mezzi e i metodi per incorporare le tecnologie
ad energia rinnovabile (RE) nei progetti e nel uso degli edifici. La memoria fornisce una panoramica delle
risorse RE e delle tecnologie disponibile utilizzate con successo per ridurre i carichi elettrici e termici degli
edifici. Vengono considerati anche metodi per applicare queste tecnologie negli edifici ed il ruolo
dell’efficienza energetica nell’edificio per progetti RE riusciti. La memoria offre anche suggerimenti per
implementare progetti RE ben riusciti.
1. INTRODUCTION
Buildings account for approximately 40% of the worldwide annual energy consumption (WBCSD
2009). Total global energy consumption in 2007 was 495 quadrillion British thermal units (Btu), meaning
the buildings sector consumed about 198 quadrillion Btu. According to the Energy Information Agency,
worldwide energy consumption is expected to increase 1.4% per year through 2035, implying that
buildings will consume 296 quadrillion Btu by the year 2035 (EIA 2010).
Fossil fuels meet a majority of world energy needs and because buildings are a large energy
consumer, they are also a major contributor to global carbon emissions and greenhouse gas (GHG)
production. It is now largely recognized that addressing energy use in buildings can reduce total fossil fuel
consumption and associated GHG emissions. Benefits such as decreased building operational energy costs
have prompted growing interest among policy makers, the technical community, and the general public in
addressing building energy issues and investigating solutions for decreasing building energy consumption.
While energy efficiency is being incorporated into new construction, existing buildings account
for a majority of the building stock that will be in place in the foreseeable future. In his 2009 presidential
address, American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE)
presidential member Gordon Holness stated that 75% to 80% of the buildings that will exist in 2030 already
exist today (ASHRAE 2010). This statistic suggests that there is an opportunity for reducing the building
sector’s contribution toward global energy consumption through reduction of energy use in existing
buildings.
Reducing existing building energy consumption consists of two synergistic approaches: (1) to
reduce the need for energy through implementation of energy efficiency measures and (2) to offset the
remaining building energy needs through use of renewable energy systems (Figure 1). It is important to
note that building energy efficiency measures should be considered first, as the cost to invest in efficiency
measures is approximately half the cost of installing renewable energy generating capacity equal to what
1
the efficiency measures offset (IEA 2006). It is advised that all energy efficiency opportunities are explored
and as many are implemented as is feasible before or in conjunction with renewable energy projects for
existing buildings. It should be noted that this paper focuses only on the opportunities and issues
surrounding implementing renewable energy projects for existing buildings.
National and local policy is being implemented in both developed and developing countries that
require greater amounts of energy to come from renewable energy resources. For example, the 2009/28/EC
Renewable Energy Sources (RES) Directive requires that 20% of energy produced within the European
Union is from renewable energy systems by 2020 compared to 2010 (European Union 2009). Also, the
2002/91/ED Energy Conservation in Buildings Directive requires building energy labeling and sets
standards for energy performance, including application of renewable energy resources (European Union
2002). As policies such as these are enacted, incentives for installing renewable energy systems are also
being developed and regulatory barriers are being removed. The use of renewable energy systems for
meeting building energy needs is also becoming a means for demonstrating leadership in environmental
sustainability and resource conservation, increasing the reliability of on-site electrical and thermal energy
supplies, addressing energy security issues, and other benefits. These actions are encouraging those who are
making decisions regarding existing building retrofit projects to seek out ways to use renewable energy
systems to meet sustainable building goals. In addition, these actions encourage those who are paying for
the energy use associated with these buildings to explore using renewable energy systems as a means to
reduce utility costs, and in many cases, the building’s carbon footprint.
2
European renewable energy resource data are available through organizations such as the Global
Energy Network Institute (GENI 2007). Renewable energy resource maps are a starting point to determine
if a building site is located in an area with acceptable amounts of renewable energy resource. However,
other factors such as the cost of alternative energy sources and available local incentives for renewable
energy installations often make installing renewable energy systems cost effective even if the resource is
not ideal. For example, Germany leads Europe in solar electric system installations with 5,351,000
megawatts peak (MWp) of cumulated installed capacity in 2008, yet, most of the country has a modest
average annual solar resource of less than 1,000 kilowatt hours per square meter (kWh/m2). Italy, on the
other hand, has a solar resource ranging from modest to very good (between 900 and 1,800 kWh/m2) and
has 317,500 MWp installed solar electric capacity as of 2008 (EurOberv’ER 2009). See Figure 2 for a
comparison between solar resources in Germany and Italy. This example illustrates how factors other than
renewable energy resource influence decisions to install solar electric systems.
Examples of renewable energy technologies that can be incorporated with building energy systems
include:
• Solar electric, or photovoltaic (PV), systems
• Solar thermal, including solar hot water (domestic water heating and space heating), and solar
ventilation air preheating
• Geothermal heat pump
• Wind turbines
• Biomass systems.
3
Figure 3. The Williams Building in downtown Boston, Massachusetts.
372 modules were installed for a total system capacity of 31 kW.
Source: Photo from SunPower, NREL/PIX 08466
Traditional single crystal solar cells are made from silicon, are usually flat-plate, and are generally
the most efficient (the solar cell efficiency is an indicator of how well it converts sunlight to direct current
electricity). Multi-crystal solar cells are a similar technology but slightly less efficient. Thin-film solar cells
are made from amorphous silicon or non-silicon materials such as cadmium telluride. Thin-film solar cells
use layers of semiconductor materials only a few micrometers thick. See Table 1 for an overview of
module efficiencies for each type of solar cell.
4
Most PV systems installed today are in flat-plate configurations, which are typically made from
solar cells combined into modules that hold about 40 cells. A typical American home will use about 10 to
20 solar panels to power the home. Many solar panels combined together to create one system is called a
solar array. For large electric utility or industrial applications, hundreds of solar arrays are interconnected to
form a large utility-scale PV system (NREL 2009). These systems are generally fixed in a single position
but can be mounted on structures that tilt toward the sun on a seasonal basis or on structures that roll East to
West over the course of a day (NREL 2011) Figure 5 shows the components of a typical PV system.
There are typically three scales of solar installations: utility-scale, commercial, and residential.
• Utility-scale installations are very large arrays located on open lands, and provide power for
hundreds or even thousands of homes and businesses.
• Commercial systems are smaller and may provide power for multiple or single commercial or
municipal buildings on campuses, in complexes, neighborhoods, or other special districts.
Commercial-scale systems offer potential advantages for locating solar PV. Rather than attempting
to find appropriate locations for solar panels on individual structures, a commercial-scale system
might be located in a less visible or impactful location, such as above a parking structure or on an
open lot. Power can be lost in transmission from these arrays to the end-use location, however, so
distances need to be minimized.
• Residential-scale PV systems produce power for use on a single property.
The major challenge with siting solar PV technologies is ensuring appropriate siting for maximum
electricity production. An ideal solar installation would be situated in an unshaded, south-facing location
with an optimum tilt angle, and would supply electricity to a site where there is a demand for the electricity
being produced. Not all sites are suitable for solar technologies, however. The following guidelines may be
helpful in determining when solar technologies are appropriate for a site:
• Identify an unshaded area for solar PV installation, particularly between peak sun hours occurring
during the middle part of the day, for example between 9:00 and 15:00. Shade will reduce the
output of a solar panel and is commonly caused by trees, nearby buildings, and roof equipment or
features (such as chimneys).
• Orient fixed-mount panels due South in the northern hemisphere and due North in the southern
hemisphere. Siting panels so that they face East or West of due South/North will decrease
efficiency. However, that effect varies by location, and could be minimal.
• Maximize the annual energy production from a fixed-mount PV system by tilting the array to
approximately match the lattitude of where the system is located. For example, a system located
at 40° north latitude shoud be tilted at approximately 40° for maximum annual efficiency.
• Install fixed-mount solar panels on roofs (flush- or tilt-mounted), or on the ground, (pole-
mounted), or integrate into building materials, such as roofs, windows, and awnings. However, a
desired tilt angle is not always feasible because of factors such as roof pitch, wind, or snow
5
loading considerations. It is possible to install panels at a different angle. The impact of a non-
ideal tilt angle varies by location, and could be minimal.
• Obtain a thorough understanding of the size and nature of an electric load to properly select and
size a PV system. PV systems can be designed to provide power simultaneously with the utility
(grid-connected); independent of the utility (stand-alone, with batteries); or to do either (dual
mode). The systems can be designed to power any percent of an electric load, from a very small
percentage to over 100% of the load, depending on available area for the panels, sun availability,
and allowances provided by utility policy to sell the energy back to the utility. When considering a
system that will be tied to the utility grid, or grid-connected, it is essential to understand the
applicable standards and rules for the serving electric utility company.
• Keep in mind the difference in efficiency of various PV modules. Efficiency is more important to
consider than the available or required area of the PV system. Fewer modules made of a higher
efficiency cell (such as single crystalline) would be needed for approximately the same power
output as more modules made of a lower efficiency cell (such as thin film). Therefore, if a project
location has limited space, then a higher efficiency, and potentially higher cost, module may make
the most sense. However, if a project has an abundance of space, then a lower efficiency, less
costly module may be more practical.
Figure 6. From left to right, examples of unglazed, glazed, and evacuated tube solar hot water systems
Sources: Photos by (from left) Albert Nunez,, NREL/PIX 10651; Todd Spink, NREL/PIX 10050; Alan Ford, NREL/PIX 09501
In general, solar water systems are reliable and low maintenance because they have few moving
parts. The primary components of a solar water heating system are the collectors and heat transfer systems,
which include a heat exchanger, pumps, hot water storage, and controls.
The guidelines previously provided for siting solar electric systems are also applicable to siting
solar thermal systems. Carefully considering siting issues will help increase the efficiency and cost
effectiveness of solar thermal system installations.
Solar Ventilation Preheating Systems. Solar ventilation preheating systems heat ventilation air
for applications needing high volumes of ventilation air. In principle, the sun warms the collector surface,
where heat is then conducted from the surface to a thermal boundary layer of air. Fans then draw the
boundary layer though holes in the collector before the heat can escape by convection (Figure 7).
6
Figure 7. Solar ventilation preheating collector operation.
Source: National Renewable Energy Laboratory
Solar ventilation preheating collectors can be added to an existing building in a retrofit project.
Factors to consider when determining whether solar ventilation preheating is a good option for a facility
include: relatively high utility rates for heating, a relatively long heating season, and the building’s south-
facing wall has enough surface area to mount the collector (Figure 8). Methods for liking the solar
ventilation preheating system to the buildings heating, ventilating, and air-conditioning system should also
be considered. These systems are low cost, reliable (no moving parts other than the fan), low maintenance,
high efficiency (up to 80% efficient), and have no storage requirements.
Figure 8. Solar ventilation preheating system installed on the U.S. Department of Energy’s
National Renewable Energy Laboratory Research Support Facility.
Source: Photo by Patrick Corkery, NREL/PIX 17412
2.3. Geothermal
Geothermal technologies use the heat from the center of the earth. Geothermal resources include
the heat retained in shallow ground, hot water and rock found a few miles beneath the earth's surface, and
extremely high-temperature molten rock called magma located deep in the earth. Almost everywhere,
shallow ground, or the upper 3 meters of the earth's surface, maintains a nearly constant temperature of
10°–16°C. Using geothermal heat pumps, this heat can be tapped to provide heating and cooling for homes
and buildings. Deeper and warmer geothermal reservoirs can be tapped directly for heat or through
advanced technologies for heat and electricity generation (DOE 2011a). Building applications for
geothermal technologies include geothermal heat pumps and direct use of the geothermal resource.
However, because geothermal heat pumps are the most common geothermal energy technology used in
buildings, this is the only geothermal technology discussed further in this paper.
7
Geothermal heat pumps use the constant temperature of the earth as an exchange medium for heat.
Although many parts of the world experience seasonal temperature extremes—from scorching heat in the
summer to sub-zero cold in the winter—the ground a meter or so below the surface remains at a relatively
constant temperature.
Geothermal heat pumps are able to heat, cool, and, if so equipped, supply homes and buildings
with hot water. A geothermal heat pump system consists of a heat pump, an air delivery system
(ductwork), and a heat exchanger—a system of pipes buried in shallow ground. In the winter, the heat
pump removes heat from the heat exchanger and pumps it into the indoor air delivery system. In the
summer, the process is reversed, and the heat pump moves heat from the indoor air into the heat
exchanger. The heat removed from the indoor air during the summer can also be used to provide a free
source of hot water.
There are four types of geothermal heat pump systems. Three of these—horizontal, vertical, and
pond/lake—are closed-loop systems. The fourth type of system is open-loop. Which system is best for a
particular site depends on the climate, soil conditions, available land, and local installation costs. All of
these approaches can be used for residential and commercial building applications (DOE 2011b).
Installing geothermal heat pumps in building retrofit projects impose an added level of complexity
of locating the loops on site and tying the geothermal heat pump system to the existing building heating,
ventilating, and air-conditioning system. These and other design factors should be carefully considered
early in the process when geothermal heat pump systems are being considered to determine if installing
such a system can be done cost effectively.
2.4. Wind
Wind energy is created by uneven solar heating of the Earth’s surface. This wind flow, or motion
energy, can be harnessed by modern wind turbines to generate electricity. Wind turbines use rotating
propeller-like blades to harness the energy in the wind and drive a turbine that generates electricity.
Before installing a wind turbine, it must be established that the wind resource in a specific location
is adequate. Wind resource is classified according to its potential to produce electricity over an annual basis
(Table 2). Wind resource maps can determine if an area of interest should be further explored, but wind
resource at a micro level can vary significantly. Therefore, it is important to evaluate the specific area of
interest before deciding to invest in wind systems.
If the site has a class 3 wind resource, consider small wind turbine (100 kW or less) or large, low-
wind speed turbine opportunities. If the site has a class 4 or greater wind resource, wind may be a good
option and even larger, utility-scale turbines may provide economic options.
Lower wind resources are less likely to be economically feasible, but should be reviewed if the
site is in a class 2 area and there are nearby pockets of class 3 resources (DOE 2011c).
Most wind turbines are designed for an operating life of up to 20 years and require little
maintenance during this period. Wind turbines require land area, so on-site wind power generation usually
occurs for projects having space for installing the turbines (Figure 9). Roof-mounted wind systems are
beginning to be used in some building projects. However, building designers should carefully consider
issues such as maintaining the building’s structural integrity, noise, and the added cost before determining
if building-mounted systems are appropriate for a specific project.
8
Figure 9. The City of Medford, Massachusetts, USA owns a
Northern Power Systems Northwind 100 wind turbine sited
at McGlynn Elementary and Middle School.
Source: Photo from Northern Power Systems, NREL/PIX 16729
2.5. Bioenergy
There are many types of biomass—organic matter such as plants, residue from agriculture and
forestry, and the organic component of municipal and industrial wastes—that can be used to produce fuels,
chemicals, and power. Wood has been used to provide heat for thousands of years. This flexibility in
materials has resulted in increased use of biomass technologies (DOE 2011d).
Biomass technologies break down organic matter to release stored energy from the sun. The
process used depends on the type of biomass and its intended end use. For example, biofuels and biopower
can be used to provide heat or electricity for buildings.
Biofuels are liquid or gaseous fuels produced from biomass. Most biofuels are used for
transportation, but some are used as fuels to produce electricity (DOE 2011e). Biofuels include ethanol and
biodiesel.
Biopower is the production of electricity or heat from biomass resources. Biopower technologies
include direct combustion, co-firing, and anaerobic digestion (DOE 2011f).
9
the wholesale rate, while others reimburse at the retail value. Some policies specify a limit on the capacity
of renewable energy systems that can participate in the net metering program.
Interconnection standards specify the technical and procedural process by which a customer
connects a renewable energy system to the grid. Such standards include the technical and contractual
arrangements by which system owners and utilities must abide.
Utilities can be reluctant to allow interconnection of DG systems. The reasons for this are often
associated with concerns over ensuring high-quality, reliable power to all customers, load management
when considering the intermittency of renewable energy power generation, safety of those maintaining the
utility distribution systems, and other similar issues. Even with the increased number of DG systems being
added to grid systems, many utilities still have limited experience with these systems. As a result, these
utilities address the interconnection questions on a case-by-case basis, which can result in a significant
amount of time needed to develop interconnection agreements.
For those pursuing grid-connected renewable energy systems for buildings projects, consider the
following steps to ensure effective relations and solutions with the utility:
• Meet up-front and often with utility representatives and develop a strategy for potential rate
structure changes as well as taking advantage of incentives the utility may be offering for
renewable energy system installations
• Work with a reputable installer/contractor with proven interconnection experience
• Size the DG system to be less than the minimum electrical load so there is no back feeding onto
the grid
• Ensure anti-islanding capabilities, which means the renewable energy system stops providing
power to the electrical grid when power from the electrical utility is no longer present (depending
on application)
• Undertake engineering studies and negotiate who pays for utility line upgrades
• Submit the interconnection proposal early.
10
Figure 10. Building-integrated solar water heating array incorporated into the historically correct,
teme-coated copper, standing-seam roof of the U.S. White House in Washington, DC.
Source: Photo from Solar Design Associates, Inc., NREL/PIX 15663
4. IMPLEMENTATION PROCESS
The process for implementing renewable energy projects for existing buildings is described in the
following steps (Figure 11).
• Engage stakeholders
• Implement projects
Figure 11. Process for implementing energy efficiency and renewable energy projects.
Source: (NREL 2011)
11
government organizations that may have funding and renewable energy targets that need to be met, as well
as financiers with knowledge of rebates, grants, third-party financing, and tax credits.
The project goals, type, and financing mechanism dictate the type of people who should be
involved as stakeholders. Although not an exhaustive list, stakeholders may include the following:
• Adjacent property owners
• Technical assistance providers such as equipment vendors
• Public recipients of grants or funding
• Planners
• Contractors
• Engineers
• Property owners
• Federal agencies
• Non-profit preservation and environmental groups
• Local government.
Entities in the construction process, such as manufacturers, contractors, and others with a vested
interest in the promotion, sale, or installation of energy efficient or renewable energy products may be
consulted for technical information relevant to the discussion, but not labeled as stakeholders.
Identifying Projects. The identification of potential projects ideally begins with an initial goal-
setting exercise. Determining, with appropriate stakeholders, what the motivations for and goals of the
project are will help define and drive the project development throughout the entire implementation
process. Goals could be related to municipality energy reduction or renewable energy use goals, building or
neighborhood environmental requirements, and building owner or tenant motivations, for example. Project
identification may include an analysis of building stock to determine which buildings have the most
feasible renewable energy installation potential, an assessment of the potential impact to the building’s
character-defining features, consideration of electricity costs or incentives available for energy projects,
and understanding energy efficiency measure that have been implemented as part of previous building
retrofit projects.
High costs of energy combined with the incentives and rebates for renewable energy installations,
along with legislation and the need for energy security, are all drivers for considering installing renewable
energy projects on existing properties. Alternate solutions for siting the renewable energy system should be
considered such as installing solar on a carport over a parking area or a ground-mounted array elsewhere on
the property instead of limiting solutions to just available roof area. There will be times when it is not
possible to roof-mount a solar system without negatively impacting a building’s character-defining
features, so one of these out-lying locations may be a viable alternative or another renewable energy
technology should be considered.
Siting renewable energy systems may not be limited to locating the systems on a single site or
structure. There is potential for “district renewable energy” and/or more distant locations than the site
allows. These types of systems could make sense in some district situations, such as grouping solar
installations on a large institutional rooftop, open field, or over a parking lot, where locating the system in a
hidden area could be a better solution than placing all the systems on visible rooftops. It should be noted
that there are technical issues related to distance, as well as legal and regulatory issues when more than one
property is involved.
12
4.3. Step 3: Follow Appropriate Review Requirements
The review process for renewable energy installations will vary according to the type of project and
the property. Properties that have been designated as historic may be protected through local historic
preservation or landmark preservation ordinances. As a result, review processes can differ greatly
depending on local and national policies for historic buildings and/or districts. To acquire more information
regarding the review process for a specific project, contact local historic building authorities for guidance.
Locally applicable environmental protection processes should also be examined. For example,
some properties are protected by preservation or conservation easements. The easement holding entity
should be involved in the renewable energy installation from the earliest phase.
CONCLUSION
European studies suggest that buildings are responsible for around 45% of global carbon dioxide
emissions over the entire life cycle (UNEP 2007). Given this large contribution to global emissions,
buildings are ripe for retrofits that result in reduced energy consumption and associated emissions. There
are many synergies between existing buildings and energy-efficient and renewable energy technologies.
Conserving and rehabilitating existing buildings to operate more efficiently and cleanly can reduce energy
use, energy cost, and GHG emissions. Retrofitting an existing building rather than building a new building
also optimizes the energy previously expended that is associated with the embodied energy in the
building’s materials and past construction. Many existing buildings are prime candidates for energy
efficiency and renewable energy technologies. In fact, older, historic buildings often have energy-efficient
features, such as natural daylighting, ventilation, and thermal storage, included in the building design.
ACKNOWLEDGEMENT
This work was supported by the U.S. Department of Energy under Contract No. DE-AC36-08-
GO28308 with the National Renewable Energy Laboratory.
REFERENCES
ASHRAE 2010. “Sustaining Our Future by Rebuilding Our Past” – President’s Address. American Society
of Heating, Refrigerating, and Air-Conditioning
Engineers. http://www.slideshare.net/ashrae6/presidents-address.
13
DOE 2011a. “Geothermal Technologies.” U.S. Department of Energy Office of Energy Efficiency and
Renewable Energy
(EERE). http://www.eere.energy.gov/basics/renewable_energy/geothermal.html. Accessed 17 July
2011.
EIA 2010. International Energy Outlook 2010, World Energy Demand and Economic Outlook. Energy
Information Agency. Report #DOE/EIA-0484(2010). Release Date: July 27,
2010. http://www.eia.gov/oiaf/ieo/world.html.
European Union 2009. Directive 2009/28/EC of the European Parliament and of the Council of 23 April
2009 on the promotion of the use of energy from renewable sources and amending and
subsequently repealing Directives 2001/77/EC and 2003/30/EC. The Official Journal of the
European Union. May 2009. http://www.energy.eu/directives/pro-re.pdf.
European Union 2009. Directive 2002/91/EC of the European Parliament and of the Council of 16
December 2002 on the energy performance of buildings. The Official Journal of the European
Union. April 2003. http://ec.europa.eu/energy/efficiency/buildings/buildings_en.htm. Accessed
25 July 2011.
IEA 2006. The World Energy Outlook 2006 Maps Out a Cleaner, Cleverer and More Competitive Energy
Future. Press Release. International Energy Agency. November 7, 2006,
London. http://www.iea.org/press/pressdetail.asp?press_rel_id=187.
NREL 2009. Learning About Renewable Energy, Solar Photovoltaic Technology. National Renewable
Energy Laboratory. http://www.nrel.gov/learning/re_photovoltaics.html. Accessed 17 July 2011.
NREL 2011. Kandt, Walker, Hotchkiss. Implementing Solar PV Projects on Historic Buildings and in
Historic Districts. NREL. Draft Technical Report. NREL/TP-7A40-51297. May 2011.
UNEP 2007. Buildings and Climate Change. Status, Challenges and Opportunities. United Nations
Environment Programme. ISBN: 978-92-807-2795-
1. http://www.unep.fr/shared/publications/pdf/DTIx0916xPA-BuildingsClimate.pdf.
14
WBCSD 2009. Energy Efficiency in Buildings. World Business Council for Sustainable
Development. http://www.wbcsd.org/DocRoot/Ge2Laeua8uu2rkodeu7q/91719_EEBReport_WEB
.pdf. Accessed 17 July 2011.
____________________
NOTE: The Alliance for Sustainable Energy, LLC (Alliance) is the manager and operator of the National Renewable Energy
Laboratory (NREL). Employees of the Alliance, under Contract No. DE-AC36-08GO28308 with the U.S. Dept. of Energy, have
authored this work. The United States Government retains and the publisher, by accepting the article for publication, acknowledges
that the United States Government retains a non-exclusive, paid-up, irrevocable, worldwide license to publish or reproduce the
published form of this work, or allow others to do so, for United States Government purposes.
15