Osciloscopio 1006

Model 1006
Automotive
Scope / GMM / OBD II Code Reader
User’s Manual
a world leader in test & measurement
FINE INSTRUMENTS CORPORATION
341-5, SONGNAE-DONG, SOSA-GU, BUCHON-SHI, KYUNGGI-DO KOREA

-TEL: (82-32) 668-6042 -FAX: (82-32) 656-5844
-E-mail: fine@finest.co.kr
© Copyright 2004 Fine Instruments Corp. All right reserved.

Specifications subject to change without notice.
Litho in Korea. FINE INSTRUMENTS CORPORATION
Menu Overview
COMPONENT TESTS MENU SENSOR TESTS MENU

SENSORS ABS Sensor (Mag)
ACTUATORS O 2S Sensor (Zirc)
ELECTRICAL Dual O2 Sensor
MAIN MENU
IGNITION ECT Sensor
COMPONENT TESTS
(or DIESEL) Fuel Temp Sensor
DANGER SCOPE
IAT Sensor
GRAPHING MULTIMETER
OBD II CODE READER Knock Sensor
VEHICLE DATA TPS Sensor
When handling any signals higher than INSTRUMENT SETUP
CKP Magnetic
CKP Hall
150 V peak, don t electrically activate CKP Optical
GRAPHING MULTIMETER MENU VEHICLE DATA MENU CMP Magnetic
B OTH CH A and/or CH B terminal(s) VOLT DC, AC CYLINDERS : 4 CMP Hall
OHM/DIODE/CONTINUITY CYCLES :4
AN D USB and/or OB D II te rminal(s) RPM BATTERY : 12 V
CMP Optical
VSS Magnetic
t o g eth er at a tim e . I f th ey a re FREQUENCY IGNITION : CONV VSS Optical
DUTY CYCLE MAP Analog
electrically activated simultaneously, a PULSE WIDTH MAP Digital
DWELL
de ath or a s er ious per son al in jury IGNITION PEAK VOLTS
MAF Analog
MAF Digi Slow
could be resulted in. IGNITION BURN VOLTS MAF Digi Fast
IGNITION BURN TIME MAF Karman-Vrtx
INJECTOR PEAK VOLTS IGNITION MENU EGR (DPFE)
INJECTOR ON TIME CONV (default)
AMP DC, AC DIS
TEMPERATURE C F DIESEL ACTUATOR TESTS MENU
LIVE Injector PFI/MFI
Injector TBI
CAUTION Injector PNP
Injector Bosch
When handing any extremely high Mixture Cntl Sol
EGR Cntl Sol
voltage signals, e.g. the signals INSTRUMENT SETUP MENU IAC Motor
DISPLAY OPTIONS DISPLAY OPTIONS MENU
generated from the spark plugs, FILTER MENU
FILTER USER LAST SETUP : OFF
IAC Solenoid
Trans Shift Sol
INPUT A : OFF
CONTRAST : 4
NEVER PUT ANY TEST LEADS (Either INPUT B : OFF AUTO POWER OFF
GRATICULE : ON
Turbo Boost Sol
LANGUAGE Diesel Glow Plug
the Red or Yellow test leads Or the VERSION INFORMATION HORIZ TRIG POS : 10 %
SCOPE CALIBRATION ACQUIRE MODE : PEAK DETECT
Secondary ignition probe lead Or ELECTRICAL TESTS MENU
Power Cable from Cigarette Lighter) Power Circuit
V Ref Circuit
CONNECTED TO THE SCOPE IN THE Ground Circuit
Alternator Output
AREAS NEAR THOSE STRONG LANGUAGE MENU AUTO POWER OFF MENU Alternator Field VR
SIGNALS. If so, the scope can be LANGUAGE : ENGLISH AUTO POWER OFF : ON
AUTO POWER OFF TIME : 30 min
Alternator Diode
Audio System
damaged or worked improperly. DC Switch Circuits
IGNITION TESTS MENU

PIP/ SPOUT
DI Primary
DIESEL MENU DI Secondary
DIESEL INJECTOR DIS Primary
ADVANCE DIS Secondary
Contents
1. INTRODUCTION
Menu Overview
1. Introduction Vehicle manufacturers have helped you locate a driveability problem by designing Electronic Control Units with
1.1 Comparing Scan Tools, DSOs and DMMs 1- 1 trouble-code generating capabilities. But, the ECUs aren’t perfect because they don’t cover everything (most glitches
1.2 Vehicle Service Manuals 1- 2 and intermittents). On-board diagnostic systems are engineered with fairly wide set limits for sensors, actuators,
2. Safety Information connectors and terminals. When a component exceeds its limit consistently, a trouble code is generated. But to keep
warranty costs in line, tolerances aren’t set to catch all transients, even though they can cause some of your worst
3. Automotive Electronic Signals driveability problems.
3.1 Primary Signal Types Found in Modern Vehicles 3- 1
3.2 Critical Characteristics of Automotive Electronic Signals 3- 2 Therefore, repair technicians are finding more and more uses for a Digital Storage Oscilloscope (DSO) and a Digital
Multimeter (DMM) thesedays. A DSO can capture a live “signature” of a circuit and store it for later analysis or
3.3 The Golden Rule of Electronic System Diagnosis 3- 2
comparison against Known-good waveforms - an invaluable resource for detecting marginal components. A GMM
3.4 Signal Probing with an Oscilloscope 3- 2
(Graphing Multimeter) gives you advanced multimeter capabilities coupled with the visual power of trend graphing
4. Getting Started and waveform display.
4.1 Product Description 4- 1
This Meter – a combination DSO, GMM, and OBD II Code Reader – represents the most powerful and versatile tool
4.2 Quick Tour 4- 2
available for troubleshooting automotive electronics since we can track down elusive no-code driveability problems
4.3 Front Panel Controls 4- 6 as well as diagnose OBD II sensors and components.
4.4 Measurement Connections 4- 7
4.5 Grounding Guidelines 4- 8
4.6 Display 4- 9 1.1 COMPARING SCAN TOOLS, DSOs AND DMMs
4.7 SCOPE Mode 4-15
4.8 GMM (GRAPHING MULTIMETER) Mode 4-16 All of these tools have unique capabilities, and today’s vehicles demand that automotive technicians are able to use
4.9 OBD II Code Reader Mode 4-17 all three tools to correctly diagnose various driveability problems. DSOs alone cannot replace DMMs or scan tools.
5. Instrument Operation By the same token, DMMs or scan tools cannot replace DSOs.
5.1 Instrument Test Modes 5- 1 For example, when anti-lock brakes on your car are sometimes erratic, you might firstly try a road test to notice that
5.2 SCOPE Displays 5- 1 the ABS light does not come on. When you get back to the shop, you plug in your scan tool and find no trouble
5.3 GMM Displays 5- 7 codes.
5.4 Dual Input Scope Operation 5-13 Because you still have your DMM, you follow the manufacturer’s instructions and you look at the output voltage from
5.5 Changing the Vehicle Data and Instrument Setup 5-13 each of the wheel speed sensors. They all appear to be in tolerance, and the manufacturer’s fault tree recommends
5.6 Freezing, Saving, and Recalling Screens 5-17 you to replace the ABS computer. Unfortunately, the ABS computer on this vehicle is embedded in the master
5.7 Glitch Snare Operation 5-18 cylinder, so you must replace everything. The worst thing is the problem still exists even after you complete all of the
5.8 Tips for Noise Management 5-19 work.
5.9 OBD II Code Reader Mode 5-20
Appendix: About OBD II System 5-24
6. Automotive Diagnostics & Applications
6.1 Component Tests 6- 1
6.2 Sensor Tests 6- 1 Normal ABS Signal
6.3 Actuator Tests 6-32
Most of the signal shown above is visible to scan tools, DSOs and DMMs.
6.4 Electrical Tests 6-48
6.5 Ignition Tests 6-57
6.6 Diesel Tests 6-68
7. Maintenance
8. Specifications Faulty ABS Signal
Glossary
However, the faults shown above are not visible to scan tools and DMMs. They are only visible to DSOs.
1-1
Menu Overview
If you had a DSO, you could look at the output signal from each of the wheel speed sensors. From this you would 2. SAFETY INFORMATION
have discovered that the left rear wheel speed sensor had some very fast aberrations that caused the ABS computer
to act strange. You replace the left rear wheel speed sensor to cure the problem. The scan tools missed this problem
because no trouble codes were set and the computer communication bus was too slow to pick up the spikes. The
DMMs missed this problem because it averaged the sensor signals and could not see the fast abberations. WARNING
Scan tools and DMMs sample very slow when compared to DSOs. DSOs are typically more than a few hundred
READ “SAFETY INFORMATION” BEFORE USING THIS MANUAL.
thousand times faster than scan tools and more than 1,000 times faster than DMMs.
There are many examples of vehicle signals that DMMs and scan tools are unable to see. There are many vehicle
problems that can occur that really require a DSO or combination DSO, DMM, and OBD II Code Reader to diagnose This instrument is designed to be used only qualified personnel who are (properly trained) skilled professional
accurately. automotive technicians.
It is assumed that the user has a thorough understanding of vehicle systems before using this instrument.
1.2 VEHICLE SERVICE MANUALS To use this instrument safely, it is essential that operating and servicing personnel follow both generally accepted
safety procedures and the safety precautions specified in this manual.
This instrument tells how to hook up it to the selected vehicle components to be tested. However, it is strongly
recommended that you consult the manufacturer’s service manual for your vehicle before any test or repair A DANGER identifies an imminently hazardous situation which, if not avoided, will result in death or serious injury to
procedures are performed in order to get the color of the wire or the PCM’s pin number from a wiring diagram. the user or the bystanders.
For availability of these service manuals, contact your local car dealership, auto parts store, or bookstore, The A WARNING identifies conditions and actions that pose hazard(s) to the user or the bystanders.
following companies publish valuable repair manuals: A CAUTION identifies conditions and actions that may damage the instrument or the vehicle.
• Mitchell International The term “Isolated (or Electrically floating)” is used in this manual to indicate a measurement in which the COM
14145 Danielson Street terminal of this instrument is connected to a voltage different from earth ground. The term “Grounded” is used when
Poway, CA 92064 the COM terminal is connected to an earth ground potential. The COM terminal of this instrument is rated up to 300
Tel : 888-724-6742 V rms above earth ground for the safety of isolated measurements.
• Haynes Publications Using Your Instrument Safely

861 Lawrence Drive Follow safe servicing practices as described in your vehicle service manual. To use this instrument safely, follow the
Newbury Park, CA 91320 safety guidelines below :
Tel : 1-800-442-9637
DANGER
• Motor Publications
5600 Crooks Road, Suite 200 • Use the instrument in service area WELL VENTILATED providing at least four change of air per hour. Engines
Troy, MI 48098 produce carbon monoxide, an odorless, colorless, and poisonous gas that causes slower action time and can
Tel : 1-800-426-6867 result in death or serious injury. Route exhaust outside while testing with engine running.
• Set the parking brake and block the wheels, especially the wheels on front-wheel drive vehicles, before testing or
• Helm Inc. repairing the vehicle because the parking brake does not hold the drive wheels.
14310 Hamilton Avenue
Highland Park, MI 48203 • Be sure there is adequate clearance between any moving components when testing. Moving components and
Tel : 1-800-782-4356 belts can CATCH loose clothing, parts of your body or the instrument and cause serious damage or personal
injury.
• Always wear approved safety eye protection when testing or repairing vehicles. Objects can be propelled by
whirling engine components can cause serious injury.
• When handling any signals higher than 150 V peak, don t electrically activate BOTH CH A and/or CH B
terminal(s) AND USB and/or OBD II terminal(s) together at a time. If they are electrically activated simultaneously,
a death or a serious personal injury could be resulted in.
1-2 2-1
Avoid Fires: • Disconnect the live test lead before disconnecting the common test lead.
• Do not position head directly over carburetor or throttle body. Do not pour gasoline down carburetor or throttle • Do not perform internal service or adjustment of this instrument unless you are qualified to do so.
body when cranking or running engine. Engine backfire can occur when air cleaner is out of normal position.
Avoid Burns:
• Do not use fuel injector cleaning solvents or carburetor sprays when performing diagnostic testing.
• Do not touch hot exhaust systems, manifolds, engines, radiators, sample probe, etc.
• The instrument has internal arcing or sparking parts. Do not expose the instrument to flammable vapors.
• Do not remove radiator cap unless engine is cold. Pressurized engine coolant may be hot.
• Do not smoke, strike a match, place metal tools on battery, or cause a spark in the vicinity of the battery. Battery
gases can ignite. • Wear gloves when handling hot engine components.
• Keep a fire extinguisher rated for gasoline, chemical, and electrical fires in work area. Fires can lead to serious • Use a suitable battery carrier when transporting batteries.
injury or death.
CAUTION
WARNING
• Disconnect circuit power and discharge all high voltage capacitors before connecting the instrument to make
Avoid Electrical Shock: resistance, continuity, or diodes measurements.
• Make sure that the vehicle to be tested is at a safe potential before making any measurement connections. • Do not rely on questionable, erratic, or obviously erroneous test informations or results. Make sure that all
connections and data entry information are correct and that the test procedure was taken correctly. Do not use
• Connect the COM input of the instrument to vehicle ground before clamping the standard SECONDARY PICKUP
suspicious test information or results for diagnostics.
(supplied) on the ignition wires. This ground connection is required IN ADDITION TO the normal measurement
ground connections.
• Do not touch ignition coils, coil terminals, and spark plugs while operating. They emit high voltages.
• Do not puncture an ignition wire to connect the instrument, unless specifically instructed by vehicle manufacturer.
• Be sure the ignition is in the OFF position, headlights and other accessories are off, and doors are closed before
disconnecting the battery cables. This also prevents damage to on-board computer systems.
IF the ground of the instrument is connected to a voltage higher than 42 V peak (30 V rms);
• Use only the standard test leads set supplied with the instrument.
• Do not use conventional exposed metal BNC or BANANA PLUG connectors.
• Use only one ground connection to the instrument (GROUND LEAD of the CH A’s shielded test lead).
• Remove all probes and test leads that are not in use.
• Connect the power adapter to the AC outlet before connecting it to the instrument.
Follow the general safety guidelines below;

• Avoid working alone.
• Inspect the test leads for damaged insulation or exposed metal. Check test lead continuity. Replace damaged
leads before use.
• Do not use the instrument if it looks damaged.
• Select the proper function and range for your measurement.
• When using the probes, keep your fingers away from probe contacts.
Keep your fingers behind the finger guards on the probes.
2-2 2-3
3. AUTOMOTIVE ELECTRONIC SIGNALS
3.1 PRIMARY SIGNAL TYPES FOUND IN MODERN VEHICLES

DECLARATION OF CONFORMITY
Once you become familiar with basic vehicle waveforms it will not matter how new or old the vehicle is, or even who
for manufactured the vehicle. You will be able to recognize signals that do not look right.
FINEST 1006 Automotive Scope / GMM / OBD II Code Reader
Direct Current (DC) Signals
Manufacturer The types of sensors or devices in a vehicle that produce DC signals are:
• Power Supplies - Battery voltage or sensor reference voltages created by the PCM.
Fine Instruments Corporation • Analog sensor signals - engine coolant temperature, fuel temperature, intake air temperature, throttle position,
341-5, Songnae-Dong, Sosa-Gu EGR pressure and valve position, oxygen, vane and hot wire mass airflow sensors, vacuum and throttle switches
Bucheon, Kyunggi-Do and GM, Chrysler and Asian manifold absolute pressure (MAP) sensors.
Republic of Korea
Alternating Current (AC) Signals
The types of sensors or devices in a vehicle that produce AC signals are:
Statement of Conformity
• Vehicle speed sensors (VSS)
• Antilock brake system wheel speed sensors (ABS wheel speed sensors)
Based on test results using appropriate standards, the product is in conformity
• Magnetic camshaft (CMP) and crankshaft (CKP) position sensors
with
• Engine vacuum balance viewed from an analog MAP sensor signal
Electromagnetic Compatibility Directive 89/336/EEC
• Knock sensors (KS)
Low Voltage Directive 73/23/EEC
Frequency Modulated Signals
Sample tests The types of sensors or devices in a vehicle that produce Frequency Modulated signals are:
• Digital mass airflow (MAF) sensors
Standards used: • Ford’s digital MAP sensors
• Optical vehicle speed sensors (VSS)
EN 61010-1/A2 (1995) & EN 61010-2-031 (1994) • Hall Effect vehicle speed sensors (VSS)
Safety Requirements for Electrical Equipment • Optical camshaft (CMP) and crankshaft (CKP) position sensors
for Measurement, Control, and Laboratory Use • Hall Effect camshaft (CMP) and crankshaft (CKP) position sensors
Pulse Width Modulated Signals

EN 61326 : 1997+A 1+A2 (1998)
The types of circuits of devices in a vehicle that produce Pulse Width Modulated signals are:
Electromagnetic Compatibility Generic Emission & Immunity Standard
• Ignition coil primary
• Electronic spark timing circuits
The tests have been performed by TÜV PRODUCT SERVICE GMBH. • EGR, purge, turbo boost, and other control solenoids
• Fuel injectors
• Idle air control motors and solenoids
This Conformity is indicated by the symbol CE, i.e.
“Conformité Européenne” Serial Data (Multiplexed) Signals
The types of circuits or devices in a vehicle that produce Serial Data signals are:
• Powertrain control modules (PCM)
• Body control modules (BCM)
• ABS control modules
2-4 • Other control modules with self diagnostics or other serial data / communications capability 3-1
To minimize this possible interference with the oscilloscope, keep these tips and suggestions in mind:
3.2 CRITICAL CHARACTERISTICS OF AUTOMOTIVE ELECTRONIC SIGNALS
°· Most interference will be picked up by the oscilloscope test leads.
Only 5 critical characteristics (or information types) given from the Automotive electronic signals are important
• Route the test leads away from all ignition wires and components whenever possible.
because the vehicle’s PCM considers them important.
• Use the shortest test leads possible, since other test leads may act as an antenna and increase the potential for
• Amplitude - The voltage of the electronic signal at a certain point in time. interference, especially at higher frequency levels that are found when probing near the vehicle°Ø s on-board
• Frequency - The time between events, or cycles, of the electronic signal, usually given in cycles per second computer.
(Hertz). • With the potential for RF interference in the engine compartment, if possible, use the vehicle chassis as ground
• Shape - The signature of the electronic signal, with its unique curves, contours, and corners. when connecting the oscilloscope test leads. In some cases the engine block can actually act as an antenna for
• Duty Cycle - The on-time, or relative pulse width of the electronic signal. the RF signals.
• Pattern - The repeated patterns within the signal that make up specific messages, like synchronous pulses that • The test leads are a very important part of any oscilloscope. Substituting other leads in both length and
tell the PCM that cylinder #1 is at TDC (Top Dead Center), or a repeated pattern in the serial data capability may alter the signals on your display.
stream that tells the scan tool the coolant temperature is 212 °F (or 100 °C), etc.
°· The oscilloscope can also pick up interference like the test leads.
• Because the oscilloscope circuits are so sensitive, and therefore powerful, do not place the oscilloscope directly
3.3 THE GOLDEN RULE OF ELECTRONIC SYSTEM DIAGNOSIS on ignition wires or near high energy ignition components, like coil packs.
• If you are using the AC or DC charger/adaptor to power the oscilloscope, keep the external power leads far
For the vehic le’s computer sy stem to function properly, it mus t send and receiv e s ignals wi th the critical away from the engine and ignition if possible.
characteristics it was designed to communicate with.
Each of the primary types of electronic signals use the critical characteristics to establish electronic communication.
They each use different combinations of the critical characteristics to communicate. Here’s a list of which critical
characteristics each of the primary signal types uses to communicate:
• Direct Current signals use Amplitude only.
• Alternating Current signals use Amplitude, Frequency, and Shape.
• Frequency Modulated signals use Amplitude, Frequency, and Shape.
• Pulse Width Modulated signals use Amplitude, Frequency, Shape, and Duty Cycle.
• Serial Data signals use Amplitude, Frequency, Shape, Duty Cycle, and Pattern.
The list will help to give you a better understanding of which signal types use which critical characteristics to do their
electronic communication. The above rules work very well and hold up in most cases, but there are exceptions to its
rules. Not many, but a few.
It may come no surprise to some that serial data signals are the most complex signals in the vehicle. They use all 5
critical characteristics to communicate with. Thus, they take a special analyzer to decode them - one very familiar to
most technicians - the scan tool.
3.4 SIGNAL PROBING WITH AN OSCILLOSCOPE
The engine compartment of a running vehicle is a very unfriendly environment for automotive signals to live.
Temperature extremes, dirt and corrosion, and electrical leaks, or noises from the high voltage pulses generated
from a typical ignition system can produce interference that can contribute significantly to the cause of many
driveability problems.
When you are probing components, sensors and circuits, be aware that the electrical noises from today’s high output
ignition systems can produce an RF energy that is similar to a radio station. Since oscilloscopes are so sensitive,
this interference can actually override the signals you are trying to capture and give you a false reading on the
display.
3-2 3-3
4. GETTING STARTED
4.1 PRODUCT DESCRIPTION
This instrument is a battery-operated 2-channel lab scope, advanced true rms graphing multimeter (GMM), and OBD
II Code Reader designed expressly for use in the automotive service market. The main purpose of this instrument is
to provide advanced troubleshooting capabilities for automotive service technicians in an easy-to-operate format.
This instrument offers the following features:
• A 25 Mega-sample/Second (one channel minimum) sample rate for rapid data updates.
• Lab scope signal patterns.
• True RMS Graphing Multimeter (GMM) measurements and graphs.
• OBD II Code Reader function.
• A unique “Glitch Snare” mode which captures, displays and optionally saves abnormal signal patterns in the
Scope mode of the COMPONENT TESTS only when they occur.
• Preset tests that enable the user to check the majority of automotive sensors, actuators and systems easily and
quickly.
• Powerful built-in reference information for each preset test which includes a test procedure showing how to
connect to the circuit, a normal reference signal pattern, theory of operation and troubleshooting tips.
• Menu-driven interface has automatic configurations for most of non-preset tes ts, s o you will find that the
instrument is easy-to-use.
• The Secondary Ignition Single function displays the waveform along with the spark voltage, RPM, burn time and
burn voltage.
• The Diesel function allows you to set injection pump timing and RPM using the optional Diesel accessories.
• USB interface supports updates for code and data.
Even though this instrument is designed to configure itself to almost any test, it is very important that you continue
through this manual and carefully read and understand the capabilities of this instrument before attempting actual
measurements.
4-1
• COMPONENT TESTS
4.2 QUICK TOUR
• SCOPE
• GRAPHING MULTIMETER
Powering the Instrument
• OBD II CODE READER
Press the POWER key to turn the instrument on. The instrument beeps once and turns on. • VEHICLE DATA
At power on, the instrument displays the VEHICLE DATA menu as shown in Figure 1. • INSTRUMENT SETUP
The fastest way to set up the instrument to test most automotive devices(sensors, actuators...) and circuits is
VEHICLE DATA MENU to choose from one of the built in COMPONENT TESTS. Each test places the instrument in a configuration best
suited to display signals for the chosen device or circuit.
CYLINDERS : 4
Default settings:
CYCLES :4 You can change the Press a Four Way arrow key to position the HIGHLIGHT BAR over the COMPO NENT TESTS menu choice and
BATTERY : 12 V settings to match with press to select.
the vehicle under test.
IGNITION : CONV
MAIN MENU
COMPONENT TESTS
Press the F1 key to Press the F5 key to
SCOPE
accept the displayed OK SELECT change the highlighted
settings. selection. GRAPHING MULTIMETER
OBD II CODE READER
Figure 1. Vehicle Data Menu at Power-On
VEHICLE DATA
INSTRUMENT SETUP
Changing the Power-On Display
BACK SELECT
Use “Instrument Setup” menu option to change the Power-On display from VEHICLE DATA MENU(default) to the
user’s last display.
Figure 2. Main Menu
Adjusting the Display Contrast
Press and Keep it depressed until you can clearly read the display.
From the resulting COMPONENT TESTS menu, select IGNITION from the test group. Then, press to select.
Resetting the Instrument
If you want to restore the instrument settings as delivered from the factory, do the following: COMPONENT TESTS MENU
1. Turn the instrument off by pressing the POWER key. SENSORS
2. Keep depressed while you turn the instrument on by pressing the POWER key. Release . You will
hear a double beep to indicate that the Master Reset has been executed. ACTUATORS
ELECTRICAL
NOTE
The Master Reset clears all memory data. IGNITION
Performing a Navigation Exercise

BACK SELECT
To display the MAIN MENU while a measurement display is active, press the MENU key to display the MAIN MENU
as shown in Figure 2. This menu lists all of the tests, displays and setups available:
Figure 2. Selecting IGNITION Menu
4-2 4-3
Next, press the Four Way arrow keys to highlight PIP/SPOUT. Press to select. Now, the instrument is ready • Press the SAVE key to save the present screen in the next memory location.
to test the input signal(s).
• Press the RECALL key to recall the screen last saved in memory.
• Press the CLEAR key to clear all the memory locations.
• Press the BACK key to resume measuring or to return to the previous display.
Power Sources and Charging the Battery

The instrument can be powered from any of the following sources:
• Internal Battery Pack
This is a rechargeable Ni-MH Battery Pack already installed.
• Power Adapter
The Power Adapter / Battery Charger powers the instrument from a standard AC outlet and charges the installed
Ni-MH Battery Pack.
The instrument can be used during battery charging. Verify that your local line voltage is appropriate before using
Figure 3. Example of Result Display
the Power Adapter to power the instrument.
• Charging Adapter (Optional)
Press to remove the Reference Waveform(s). This adapter charges the instrument’s Ni-MH Battery Pack from a standard 12 V DC cigarette lighter outlet
Press to enter the scope into the test mode and continue to display the Reference Waveform(s) for
comparison to a live waveform(s). WARNING
For this demonstration, view the following reference information specific to the test selected. Reference information TO AVOID ELECTRICAL SHOCK, USE A BATTERY CHARGER THAT IS
is available at any time by pressing the HELP key. Press when finished viewing each area under the HELP AUTHORIZED FOR USE WITH THE AUTOMOTIVE SCOPE.
menu.
USE the following procedure to charge the battery pack and to power the instrument:
Test Procedure - Tells how to hook up the scope, and what accessories to use. Describes how to stimulate the
sensor or operate the circuit to obtain a diagnostic waveform. 1. Connect the Power Adapter / Battery Charger to line voltage.
Reference Waveform (REF WFM) - Shows a typical good or normal signal pattern. Describes significant waveform 2. Insert the Power Adapter’s low voltage plug into the Power Adapter connector of the instrument. You can now use
features or variations. the instrument while the Ni-MH batteries are being charged slowly. If the instrument is turned off, the batteries are
charged more quickly.
Theory of Operation - Explains what the sensor or circuit does and the important signals involved.
During operation, when the batteries are low, a battery symbol appears on the top right of the display. When
Troubleshooting Tips - Tells the symptoms caused by the defective component and how to fix up the problems. this occurs, replace or recharge the internal battery pack immediately.
Function Information - Explains about the particular function keys that can be used for the selected test for certain 3. The Power Adapter uses a trickle charging method for the batteries, so no damage can occur even if you leave it
COMPONENTS. charging for long periods.
Typically a 8 hour recharge during instrument working and a 4 hour recharge during instrument off provides the
Pressing moves back through the previous displays to return to active tests or to test selected menus. instrument with the maximum use of 4 hours.
After you choose a preset test, you may change most instrument settings to get a better look at the signal. You can Auto-Power-Off
even change to different display modes, moving between Scope mode and GMM mode as needed, by pressing the
GMM MODE function key in the Scope display or the SCOPE MODE function key in the GMM display. When operated on batteries (no adapter connec ted), the instrument c onserves power by turning itself off
automatically, if you have not pressed a key for 30 minutes or if the battery level is too low. The instrument turns back
You can hold the information in memory at any time by pressing the HOLD key to freeze the display. Notice that on if the POWER key is pressed.
SAVE, RECALL, and CLEAR function key label is displayed above the Function key on the bottom display after
is pressed. The Auto-Power-Off will be disabled automatically when enters the GMM mode.
You can adjust the Auto-Power-Off time between 5 minutes and 120 minutes to use “Instrument Setup” menu option.
4-4 4-5
4.3 FRONT PANEL CONTROLS ITEM KEYS DESCRIPTION
Sets automatic ranging on and off (toggle).
Key Control Overview When on, t he top right display shows A UTO. When t his f unction is set on, it
searches for the best range and time base settings and once f ound it t racks the
Display area for the
signal. When this function is off, you should manually control ranging.
Function Key Labels
Turns the LCD Backlight on and off.
Turns the power on and off (toggle). When you turn the power on, previous settings
are activated.
Allows you to use cursors for measurements on waveforms. A cursor is a vertical
line or a horizontal line that you can move over the waveform like a ruler to measure
values at specific points.
Freezes the display (HOLD is displayed at the top right). Also displays a menu to
save or recall screens or to clear the memory.
Takes you back to the main navigation menu.
Figure 4. Key Control Overview 4.4 MEASUREMENT CONNECTIONS
Key Descriptions
ITEM KEYS DESCRIPTION

to These are the Function keys.
The function assigned to each key is indicated by the Function Key Label displayed
above the key on the bottom display.
Displays information about the highlighted menu choice during menu selection.
Displays information about the function keys when a selected test is running.
Figure 5. Measurement Connections
Performs one of the following actions:
• Moves up and down through menu choices.
• Moves a waveform up and down. INPUT A (Red)
• Moves a voltage cursor up and down. INPUT A is used for all single channel measurements, sometimes combined with use of the other inputs, Various
• Adjusts the trigger level when you are in the SCOPE mode. test leads and adapters are required depending on the type of measurement selected.
Performs one of the following actions:
• Moves a waveform right and left. INPUT B (Yellow)
• Moves a time cursor left and right.
INPUT B is used in conjunction with INPUT A.
Ranges amplitude up and down for both channels (CH A & CH B). • In COMPONENT TEST mode,
for DUAL O2 SENSOR measurements.
for PIP/SPOUT measurements.
Ranges Time Bass up and down for both channels (CH A & CH B). for ADVANCE measurements.
• In SCOPE mode you can use the instrument as a dual trace oscilloscope with INPUT A and INPUT B connected.
4-6 4-7
COM, TRIGGER 3. Measurement faults or short circuit with the DUAL INPUT SCOPE mode. This occurs when you perform floating
measurements with grounding at different points.
Used as external trigger for probes with dual banana plugs, such as the RPM Inductive Pickup.
INPUT A INPUT A
TRIGGER (as single input)
Used in SCOPE mode to trigger (or start) acquisitions from an external source.
INPUT B
INPUT B
COM (as single input)

Used for safety grounding when the Capacitive Secondary Pickup is connected to the ignition system.
(Incorrect Grounding) (Correct Grounding)
WARNING
S hort Circuit by Grounding on Dif ferent Grounding at One Point
T O AVO ID ELECTRICAL SHO CK, CO NNECT THE COM INPUT OF THE Potentials
INSTRUMENT TO VEHICLE GROUND BEFORE CLAMPING THE CAPACITIVE
SECONDARY PICKUP(SUPPLIED) ON THE IGNITION WIRES. Instrument Grounding for Measurements on the Ignition System
THIS GROUND CONNECTION IS REQUIRED IN ADDITION TO THE NORMAL For the instrument safety, connect the COM input to engine ground before you perform measurements on the
MEASUREMENT GROUND CONNECTIONS. ignition system with the Capacitive Secondary Pickup.
For other tests, the COM input should not be connected to engine ground when the probes have their own ground To prevent ground loops, connect all ground leads to the SAME engine ground.
connection at the probe end. See the GROUNDING GUIDELINES.
4.6 DISPLAY
4.5 GROUNDING GUIDELINES
The instrument presents “live” measurement data in the form of Scope and GMM displays. Temporary displays are
Incorrect grounding can cause various problems: used to display frozen and saved measurement data.
Menus are provided as a means of choosing instrument’s measurement configuration. To display the MAIN MENU
1. A ground loop can be created when you use two ground leads connected to different ground potentials. This can
while a measurement display is active, press the MENU key at any time.
cause excessive current through the grounding leads.
INPUT A INPUT A Menu Display
When you press MENU key, the instrument displays the MAIN MENU. To select a menu option, use the Four Way
COM
arrow keys to move the highlight bar to the desired item. Then press . To exit the MAIN MENU and return to
the previous setup, press . During menu selection, the bottom part of the screen is used to display the function
key menu.
(Incorrect Grounding) (Correct Grounding)
Ground Loop by Double Grounding on Shield of Test Lead Connected to Ground MAIN MENU
Different Grounds COMPONENT TESTS
SCOPE
2. Excessive noise shown on the measured signal. GRAPHING MULTIMETER
INPUT A OBD II CODE READER
COM VEHICLE DATA
INSTRUMENT SETUP
BACK SELECT
(Incorrect Grounding)
Noise Pickup on Unshielded Ground Lead
4-8 4-9
COMPONENT TESTS
COMPONENT TESTS MENU SENSOR TESTS MENU
Leads to a series of predefined setups to test most common sensors and circuits.
ACTUATORS O 2S Sensor (Zirc)
SCOPE MAIN MENU
IGNITION ECT Sensor
COMPONENT TESTS
Use Single Input Scope mode if you want to measure a single signal, INPUT B is turned off. Use Dual Input Scope SCOPE
mode if you want to simultaneously measure two waveforms - one on INPUT A and the other on INPUT B. GRAPHING MULTIMETER IAT Sensor
GRAPHING MULTIMETER CKP Magnetic
INSTRUMENT SETUP
CKP Hall
INPUT A is used for all GMM(Graphing Multimeter) tests. The probes and test leads to be used depend upon the CKP Optical
type of test performed. GRAPHING MULTIMETER MENU VEHICLE DATA MENU CMP Magnetic
VOLT DC, AC CYLINDERS : 4 CMP Hall
OHM/DIODE/CONTINUITY CYCLES :4 CMP Optical
OBD II CODE READER RPM BATTERY : 12 V VSS Magnetic
FREQUENCY IGNITION : CONV VSS Optical
OBD II input terminal in flank is used for the OBD II Code Reader mode. Connect the standard OBD II cable DUTY CYCLE MAP Analog
supplied to the vehicle’s sixteen-pin DLC (Data Link Connector). PULSE WIDTH MAP Digital
DWELL MAF Analog
IGNITION PEAK VOLTS MAF Digi Slow
VEHICLE DATA IGNITION BURN VOLTS MAF Digi Fast
IGNITION BURN TIME
Set the vehicle data to match the vehicle under test. If they do not match, you could get incorrect test results and MAF Karman-Vrtx
may not be able to select all available tests for this vehicle. This menu appears at power-on as the start-up display INJECTOR ON TIME CONV (default)
due to its importance. AMP DC, AC DIS
INSTRUMENT SETUP Injector TBI
Injector PNP
Use this menu option to set the following: Injector Bosch
• Optimal settings for display. Mixture Cntl Sol
EGR Cntl Sol
• Filter function enabled and disabled. INSTRUMENT SETUP MENU IAC Motor
• Auto-Power-Off enabled and disabled and adjusting the Auto-Power-Off time. FILTER MENU DISPLAY OPTIONS DISPLAY OPTIONS MENU IAC Solenoid
• Language for menus and HELP text. FILTER USER LAST SETUP : OFF Trans Shift Sol
INPUT A : OFF
AUTO POWER OFF CONTRAST : 4 Turbo Boost Sol
• Version Information of current software. INPUT B : OFF
GRATICULE : ON
LANGUAGE Diesel Glow Plug
• Scope Calibration when using the scope in abnormal operating environments. VERSION INFORMATION HORIZ TRIG POS : 10 %
ELECTRICAL TESTS MENU
Menu Overview Power Circuit
V Ref Circuit
Figure 6. shows an overview of available test functions, displays and setups from the MENU key. The MAIN MENU Ground Circuit
choices represent categories of applications that are listed in sub-menus as shown in the following figure. Alternator Output
LANGUAGE MENU AUTO POWER OFF MENU Alternator Field VR
LANGUAGE : ENGLISH AUTO POWER OFF : ON Alternator Diode
AUTO POWER OFF TIME : 30 min Audio System
DC Switch Circuits
IGNITION TESTS MENU

PIP/ SPOUT
DI Primary
Figure 6. Automotive Test Functions & Setups Overview
4-10 4-11
Getting Reference Information for the Selected Test Screen Displays
Reference information is available at any time by pressing the HELP key.
Press when finished viewing each area under the HELP menu.
HELP MENU
TEST PROCEDURE
REFERENCE WAVEFORM
THEORY OF OPERATION
TROUBLESHOOTING TIPS
Figure 8. Single and Dual Input scope in COMPONENT TESTS
FUNCTION INFORMATION
Use Dual Input Scope mode if you want to simultaneously measure two waveforms - one on INPUT A and the other
on INPUT B.
BACK SELECT
Use SINGLE INPUT SCOPE mode if you want to measure a single signal, INPUT B is turned off.
Use DUAL INPUT SCOPE mode if you want to simultaneously measure two signals.
Getting Information About the Function Keys During a Running Test Using the Function keys
For each test, one or more Function Key Labels are displayed, depending on the sub-selections possible. The
When you press this key during a running test, you get information about the function keys that can be used
Labels indicate what the keys do when you press them. (See the following example.)
for the test.
For example, IGNITION DI SECONDARY

VEHICLE WFM CYLINDER
Function Key Labels
BACK RUN
DATA ERASE PARADE
DI Primary DI Primary Function keys

Page 1 of 2 Page 2 of 2
Function Info Function Info
Figure 8. Function Key Labels for SECONDARY IGNITION
VEHICLE CYLINDER FAST KEYS VEHICLE CYLINDER FAST KEYS
DATA SINGLE UPDATE TRIG LVL DATA SINGLE UPDATE TRIG LVL
Pressing a function key that has no label has no effect.
VEHICLE Giv es a list of options to define FAST Turns all readings off to make the
UPDATE measur em ent faster and m ore
The same Function Key Label can appear in several tests and it performs a similar function.
DATA the type of vehicle under test.
reliable.
CYLINDER S IN GLE -displays the ignition
SINGLE pattern of one single cylinder. KEYS You can adjust trigger level for a Examples of Function Key Labels
TRIG LVL stable display by using the four
PARADE P AR AD E-displays the ignition way arrow keys.
CYLINDER Two separate functions can be allowed to the same function key.
pattern of all cylinders in firing PARADE You can use the function key to toggle between the functions.
order. SINGLE When you press , you can select between PARADE and SINGLE cylinder test.
PAGE PAGE
BACK BACK
DOWN UP
When you press , OHM becomes the active function. When
Figure 7. Information About the Function keys CONTINUTY you press , Diode ( ) becomes the active function. When
OHM
OPEN CLOSE
you pres s , OPEN CO NTINUITY becomes the active
function. Pressing , CLOSE CONTINUITY becomes the
active function.
4-12 4-13
KEYS The KEYS icon indicates that you can use the Four Way arrow keys to change Volt & Time
RANGE A 4.7 SCOPE MODE
ranges, to move the waveform position, and to adjust the trigger level for either INPUT A or INPUT B.
MOVE A And also you can use the Four Way arrow keys to adjust the sensitivity level in the COMPONENT
TRIG LVL
TEST (IGNITION mode).
SENS LVL SCOPE mode provides a display of signal patterns from
Press to toggle among RANGE A , MOVE A , TRIG LVL , and SENS LVL for INPUT A,
either CH A or CH B over times ranging from 1 µs to 50
or among RANGE B , MOVE B , and TRIG LVL for INPUT B.
seconds per division, and for voltage ranges from 50 mV
to 300 V full scale.
KEYS The icon indicates that you can use the Four Way arrow keys to move CURSOR 1 (if CURSOR 1
CURSOR 1 is highlighted) or move CURSOR 2 (if CURSOR 2 is highlighted). Press the function key to toggle
CURSOR 2 The display may be triggered at all time settings, and
between CURSOR 1 and CURSOR 2.
trigger slope and level may be adjusted as needed. The
scope display is defaulted in Glitch Detect mode to display
REPEAT This Label is displayed for SINGLE DISPLAY tests, for example the knock sensor test. To repeat the
even the narrowest glitches.
TEST test, press the function key, then perform the required action. The knock sensor test is a single shot
measurement, which means that the signal from the knock sensor is displayed only once. To get a new
The SINGLE INPUT SCOPE mode (Component Tests
test result, you have to press the key and then tap the engine block or the sensor again. You
onl y) provi des for the di splay of up to four meter
may have to readjust the vertical RANGE to get an optimal waveform.
measurements above the waveform viewing area.
INVERT To change to the opposite polarity. Puts the waveform display upside down.
OFF
Figure 9. Scope Mode Indicators
ON
GMM This Label is displayed in the Scope test mode of the COMPONENT TESTS only.
MODE To change from Scope test mode to GMM test mode, press the function key. Indicate meter measurement function.
Indicate HOLD function enabled.
SCOPE This Label is displayed in the GMM test mode of the COMPONENT TESTS only.
Backlit indicator.
MODE To change from GMM test mode to Scope test mode, press the function key.
Low battery indicator.
GLITCH This Label is displayed in the Scope test of the COMPONENT TESTS only. Indicate SCOPE mode.
SNARE To capture, display, and optionally save abnormal signal patterns when they occur, press the function Indicate AUTORANGING mode.
key. Indicate FILTER function enabled.
Indicate time base per division.
Indicate trigger level voltage.
Blank if DC, ~ if AC.
Indicate trigger slope (rising or falling).
Indicate AUTO triggered.
Indicate voltage per division and coupling.
Blank if DC, ~ if AC, if GND.
Indicate signal source channel.
Indicate INPUT A zero level.
Indicate trigger location.
4-14 4-15
4.8 GMM (GRAPHING MULTIMETER) MODE 4.9 OBD II CODE READER MODE
GMM mode plots the results of signal measurements such OBD II Code Reader mode is designed to retrieve the
as frequency as the values change with time. The time Diagnostic Troubl e Codes ( DTCs) from the v ehi cle
range in GMM mode may be set manually from 5 seconds Powertrain Control Module (PCM) and to provide an
to 24 hours per display. indication of I/M Readiness Monitor status.
Ranges for the vertical scale may also be set manually, This mode is very suitable to identify a particular problem
and the available range depends upon the measurement area and ensure the correctness of the scope or G MM
being displayed. testing results having obtained from the same problem
area tests.
Where possible, measurements plotted in GMM mode are
performed on a cycle-by-cycle basis, resulting in extremely
fast response.
This mode is very suitable to find faults in slowly changing

processes.
Figure 10. GMM Mode Indicators Figure 11. OBD II Code Reader Mode Indicators
Indicate meter measurement functions. Vehicle icon - Indicates whether or not the instrument ( in the Code Reader mode) is being properly powered
NOW: Most recent meter reading. through the vehicle’s Data Link Connector (DLC). A visible icon indicates that the instrument is being powered
MAX: Maximum value since last reset. through the vehicle’s DLC connector.
MIN: Minimum value since last reset.
Link icon - Indicates whether or not the instrument (in the Code Reader mode) is communicating (linked) with the
Indicate HOLD function enabled. vehicle’s on-board computer. When visible, the instrument is communicating (linked) with the PCM. If the Link
Low battery indicator. icon is not visible, the instrument is not linked to the PCM.
Indicate GMM mode. Battery icon - Low battery indicator of the instrument.
Indicate AUTORANGING mode. Pressing sets automatic ranging on. Using the Four Way arrow keys for Monitor icons - Indicates which Monitors are supported by the vehicle under test, and whether or not the
ranging turns automatic ranging off and extinguishes AUTO. associated Monitor has run its diagnostic testing. When a Monitor icon is Solid, it indicates that the associated
Indicate voltage per division. Monitor has completed it’s diagnostic testing. When a Monitor icon is Flashing, it indicates that the vehicle
supports the associated Monitor, but the Monitor has not yet run its diagnostic testing. On OBD II systems, a
Indicate time per display.
maximum of eleven Monitors are utilized. Not all Monitors are supported by all vehicles.
Indicate signal source channel. When the instrument is linked to a vehicle, only the icons for Monitors that are supported by the vehicle under
test are visible on the display.
Following is a list of Monitor icons and their associated Monitors:
CC - Comprehensive Component Monitor
MIS - Misfire Monitor
FUEL - Fuel System Monitor
O2 - Oxygen Sensor Monitor
HO2 - Oxygen Sensor Heater Monitor
C - Catalyst Monitor
HC - Heated Catalyst Monitor
EGR - Exhaust Gas Recirculation (EGR) Monitor
EVAP - Evaporative System Monitor
2A - Secondary Air System Monitor
AC - Air Conditioning System Refrigerant (R-12) Monitor
4-16 4-17
MIL - Indicates the status of the Malfunction Indicator Lamp (MIL). 5. INSTRUMENT OPERATION
This icon is visible only when a DTC has commanded the MIL to illuminate on the vehicle’s dash.
Code Number Sequence - The instrument assigns a sequence number to each DTC that is present in the PCM’s
memory, in ascending order, starting with “01”. This helps keep track of the number of DTCs present in the 5.1 INSTRUMENT TEST MODES
PCM’s memory. Code number “01” will always be the highest priority code, and the code for which “Freeze
Frame” data has been stored. From the MAIN MENU, you can choose 4 independent instrument test modes:
Pending icon - Indicates if the currently displayed DTC is a Pending Code.
• COMPONENT TESTS
Vehicle Manufacturer Display Area - Displays the name of the vehicle manufacturer, whose Manufacturer • SCOPE
Specific DTC Definition or Generic DTC Definition will be displayed along with the associated DTC, if a fault will • GRAPHING MULTIMETER
be detected. “Generic” or a manufacturer among GM, Ford, Chrysler, Toyota, and Honda can be selected by the • OBD II CODE READER
key.
DTC Definition Display Area - Displays the DTC Definition per the currently displayed DTC. The fastest way to set up the instrument to test most devices and circuits is to choose from one of the built in
DTC Display Area - Displays the Diagnostic Trouble Code (DTC) number. CO MPO NENT TESTS. These tests preset the instrument to either Single or Dual Input Scope mode. Most
Each particular fault is assigned a Code Number that is specific to that fault. instrument settings may be adjusted manually once you have chosen a Component Test, enabling you to fine tune
settings to get a better look at the signal. Changes you make to settings specific to a Component Test are
RUN - Indicates the Monitor RUN status of all the Monitors that apply to the vehicle under test.
temporary, and are restored to their preset values each time another test is chosen. When configured for a specific
DONE - When visible, indicates that all the Monitors that apply to the vehicle under test have run and completed Component Test, the instrument displays the reference waveform and data as well as the name of the test on the
their Diagnostic Testing, DONE is visible only when all supported Monitors have completed their testing. bottom display along with the Function Key Labels specific to the test chosen.
MONITOR - Identifies the Monitor icon area.
If you prefer total control over your instrument configuration, choose SCOPE test mode from the MAIN MENU.
NOTE: Items 11 through 13 are associated with I/M Readiness Monitor Status. Some states of U.S.A. require Settings for SCOPE are separately preserved and restored each time you choose SCOPE from the MAIN MENU.
that all vehicle Monitors has run and completed their Diagnostic Testing before a vehicle’s Emissions Test (or Thes e settings are not affected when you choose a Component Test. This is also true for the G RAPHING
Smog check). MULTIMETER test mode, so in effect they are “custom” setups.
5.2 SCOPE DISPLAYS
Using Single and Dual Input Scope Mode

The instrument can be configured to show scope displays for either CH A or CH B signals: In DUAL INPUT SCOPE
mode, both CH A and CH B may be displayed at the same time.
Use SINGLE INPUT SCOPE mode if you want to measure a single signal, INPUT B is turned off.
Use DUAL INPUT SCOPE mode if you want to simultaneously measure two signals.
SCOPE
4-18 5-1
Function keys and Result Screen SCOPE displays are defaulted in “Glitch Detection” mode. This means that all signals are sampled at the full sample
rate of the instrument and the minimum and maximum excursions are always shown on the display, even if the
horizontal time setting is too slow to show each individual sample interval. In this mode, every noise spike of 40 ns
and wider will be displayed.
INPUT A Control Functions

When you are in SCOPE, you can control the INPUT A functions as follows:
SCOPE
INPUT INPUT SINGLE KEYS
TRIGGER
A B SHOT MOVE A
SCOPE INPUT A
COUPLING INVERT KEYS
BACK DC OFF MOVE A
Automatic ranging and signal tracking is on. Press t o return to the Press to invert the INPUT A
previous menu. signal waveform.
Pressing sets automatic ranging and signal tracking on and off.
If on, AUTO is displayed, if off, AUTO is disappeared. Press to select DC, AC or GROUND coupling.
Trigger level voltage of INPUT A.
DC Coupling allows you to measure and display both the DC and AC components of a signal. AC Coupling blocks
Time base range.
the DC component and passes the AC component only. GND grounds the input of the instrument internally.
Trigger icon. Indicates trigger slope ( indicated negative slope).
Auto triggered. INPUT B Control Functions
INPUT A range setting.
INPUT B range setting. When you are in SCOPE, you can control the INPUT B functions as follows:
Indicates signal source channel A. SCOPE
INPUT A zero level. INPUT INPUT SINGLE KEYS
TRIGGER
Indicates trigger location. A B SHOT MOVE A
Indicates signal source channel B.

INPUT B zero level.
Making an Easy Setup SCOPE INPUT B

DISPLAY COUPLING INVERT KEYS
BACK
When you enter the scope mode, the instrument automatically optimizes vertical range, time base, and trigger OFF DC OFF MOVE B
settings to create a stable display. (Autoranging is default)

Press to invert the INPUT B
• When you press one of the Voltage and Time control keys, the instrument switches to manual control of range signal waveform.
Press to turn INPUT B on or off.
and trigger settings.
Press to select DC, AC, or GROUND coupling.
• Press to toggle between automatic and manual control of range and trigger settings. Use this key if you
cannot get a stable display using manual control. When you entered SINGLE DISPLAY, INPUT B is turned off by default, but you can turn it on by pressing F2.
5-2 5-3
Single-Shot Function AUTO versus NORMAL acquisitions
Normally the scope mode automatically repeats the measurements to acquire waveforms by the recurrent If you select AUTO, the instrument always performs acquisitions, i.e., it always displays the signals on the input. If
acquisition mode. NORMAL is selected, a trigger is always needed to start an acquisition.
SINGLE-SHOT allows you to perform single acquisition to snap events that occur only once. REPEAT TEST ( )
is used to start a next single acquisition. TRIGGER SLOPE
SCOPE If you select , trigger occurs at a rising(positive) edge of the signal.

INPUT INPUT SINGLE KEYS If you select , trigger occurs at a falling(negative) edge of the signal.
TRIGGER
A B SHOT MOVE A
TRIGGER SOURCE
If you select TRIGGER SOURCE A (default), acquisitions start when the signal on INPUT A fulfills the selected
trigger conditions.
SCOPE SINGLE SHOT If you select TRIGGER SOURCE TRIG, the previous rule is valid for the signal on the TRIGGER input.
SINGLE REPEAT KEYS
BACK OFF TEST MOVE A TRIGGER LEVEL
This function allows you to set the level that the signal must cross to trigger acquisitions.
Normally, after you enter SINGLE or DUAL INPUT SCOPE mode, the AUTO RANGE function automatically sets
Press to repeat a single-shot acquisition. and maintains an optimal trigger level as the signal changes.
Move the trigger level icon (or icon) to the desired level by using and keys.
Trigger Control Functions
HORIZONTAL TRIGGER POSITION (HORIZ TRIG POS)
TRIGGER is a set of conditions that determine whether and when acquisitions start. The following will determine the
trigger conditions: You can use the INSTRUMENT SETUP menu to set the Horizontal Trigger Position (Horiz Trig Pos) to three
different horizontal locations on the display, depending on whether you want to see conditions that led up to the
• Select INPUT A or TRIGGER as the TRIGGER SOURCE input. trigger event, or those following it.
• Use AUTO or NORMAL acquisitions.
• Select trigger to occur on a positive or negative SLOPE of the signal. • 10 % Trigger located close to left edge of display.
• SET the trigger LEVEL. • 50 % Trigger located at center display.
• 90 % Trigger located close to right edge of display.
If you change the trigger level, the AUTO RANGE function is turned off.
Use 10 % Trigger to show events which happen after the trigger.
When you are in SCOPE, you can control the trigger functions as follows: Use 90 % Trigger to show events leading up to the trigger.
SCOPE Noise Filter Function

INPUT INPUT SINGLE KEYS
A B SHOT TRIGGER TRIG LVL There are cases where you may want to filter out noises in order to see a better signal. This can be especially true
Press to select the trigger level adjustment. when ignition noise is present. The instrument provides a noise filter for each input channel which reduces the
bandwidth from its normal 5 MHz to 2 KHz. You can enable or disable CH A Filter or CH B Filter using the
INSTRUMENT SETUP menu. When enabled, the FILTER indicator appears on the screen.
SCOPE TRIGGER
MODE SLOPE SOURCE COUPLING
BACK AUTO A DC
Press to select DC or AC.
Press to select AUTO or Press to select the trigger source.

NORMAL acquisitions.
Press to select the trigger slope.
5-4 5-5
Cursor Key Function For VOLTS CURSORS,
A cursor is a vertical line or a horizontal line placed over the displayed waveform to measure values at certain points. Volts dif feren ce b etw een C URSO R 1 a nd Samp le va lue at
CURSOR 2 positions on the INPUT A waveform.
The instrument can measure signal details by using Cursors. This function is not possible for all tests. CURSOR 2 position
on th e I NPUT A
Press to display the Function key Menu for cursor operation. Samp le va lue at waveform.
CURSOR 1 position
If cursor operation is not possible for the actual measurement, the instrument beeps to alert you. on th e I NPUT A VOLTS 1 DELTA VOLTS 2
VOLTS 1 DELTA VOLTS 2
Two cursors (vertical lines) appear on the display. waveform.
2.4 V 7.2 V 9.8 V A: 130 mV 520 mV 650 mV
The left cursor is named CURSOR 1, the right CURSOR 2. B: 24.0 mV 74 mV 98.0 mV
Sa mple valu e at Sample value a t Sa mple value at Samp le va lue at
VOLTS CURSOR 1 VO LTS CURSO R CURSOR 1 position CURSOR 2 position
p osition on t he 2 posit io n o n t he o n t he I NPUT B on th e I NPUT B
CURSORS waveform. waveform. waveform. waveform.
CURSOR KEYS Volts difference between CURSOR 1
BACK Volts difference between CURSOR 1
TIME CURSOR 1
and CURSOR 2 positions.
an d CUR SOR 2 posit ion on t he
INPUT B waveform.
• Press to set TIME cursor or VOLTS cursor or cursor OFF. Reading Test Results on the SCOPE (Component Tests only) Display
• Press to select the cursor you want to move (1 or 2).
Measurement results can be displayed as numeric values (referred to as readings) and waveform. The types of
• Use the Four Way arrow keys to move the cursors. readings depend on the test taking place.
The top display shows readings related to values at the cursor positions. For example, during a O2S SENSOR (Zirc) test, MAXIMUM and MINIMUM values are displayed as readings and
during a DUAL O2 SENSOR test MAXIMUM and MINIMUM values of the signals from the oxygen sensor before and
For TIME cursors, after the catalytic converter are displayed as readings. During a DI SECONDARY test, SPARK VOLTAGE, RPM,
BURN TIME, and BURN VOLTAGE are displayed as readings.
TIME 1 DELTA TIME 2 The values you see on the display most often depend on the vehicle under test. Refer to the Service Manual of the
20.4 ms 48.1 ms 68.5 ms vehicle manufacturer.
Sample value at TIME CURSOR In Chapter 6 “Automotive Diagnostics & Applications” you can find typical results of certain applications.
Sample value at TIME CURSOR 2
1 position on the waveform(s). position on the waveform(s).
Time difference between TIME CURSOR 1 5.3 GMM DISPLAYS

and TIME CURSOR 2 positions.
The instrument performs cycle by cycle measurements of a variety of signal characteristics in Real Time and plots
them as they change with time as a graph. The instrument also performs certain other measurements on a
continuous basis, delivering the results for graphing 20 times per second. You can also plot the input signal directly
(as in SCOPE mode) by choosing LIVE.
The GMM display includes a meter reading showing the current value of the graphed parameter. This reading is an
average over many result values. In some cases, measurements are the maximum or minimum of a series of signal
values over the most recent 1 second interval.
The following table shows measurements which can be plotted in GMM displays and the type of graphing and
readout.
5-6 5-7
Code Measurement Graphing Type Using Graphing Multimeter (GMM)
DC VOLT DC Average Continuous MAIN MENU GRAPHING MULTIMETER MENU

AC VOLT AC Average Continuous COMPONENT TESTS VOLT DC, AC
SCOPE OHM / DIODE / CONTINUITY
AC+DC VOLT AC+DC Average Continuous
GRAPHING MULTIMETER RPM
OHM Ohms Continuous FREQUENCY
OBD II CODE READER
DIODE Diode drop Continuous DUTY CYCLE
VEHICLE DATA PULSE WIDTH
CONTINUITY Continuity Continuous
INSTRUMENT SETUP DWELL
RPM RPM Cycle by Cycle
IGNITION PEAK VOLTS
FREQUENCY Frequency Cycle by Cycle IGNITION BURN VOLTS
DUTY CYCLE Duty Cycle Cycle by Cycle IGNITION BURN TIME
PULSE WIDTH Pulse Width Cycle by Cycle INJECTOR PEAK VOLTS
DWELL Dwell Cycle by Cycle INJECTOR ON TIME
AMP DC, AC
IGNITION PEAK VOLTS Ignition Peak Volts Cycle by Cycle TEMPERATURE °C, °F
IGNITION BURN VOLTS Ignition Burn Volts Cycle by Cycle LIVE
IGNITION BURN TIME Ignition Burn Time Cycle by Cycle
INJECTOR PEAK VOLTS Injector Peak Volts Cycle by Cycle
INJECTOR ON TIME Injector On Time Cycle by Cycle Making Connections
TEMPERATURE Temperature °C, °F Continuous
INPUT A is used for all GMM tests just except the RPM measurement. The probes and test leads to be used depend
LIVE Live Direct input samples
on the type of test performed. When you select certain GMM tests, a connection help screen will guide you by
pressing . This tells you which probe or test lead to use and where to connect it.
Vertical and Horizontal Scaling Function Key Labels for Each Test
Testing Volt DC, AC
GMM VOLT
MAX/MIN REPEAT
Press to start plotting a new
DC AC AC+DC
Press to measure DC RESET TEST graph as new samples are
voltage. acquired.
Press to measure AC Press to reset maximum

true rms voltage. and minimum.
Press to measure AC+DC true rms voltage.
Figure 13. Changing Vertical and Horizontal Ranges
The vertical and horizontal ranges in GMM displays are manually adjustable by using the Four Way arrow keys. You can stop graphing by pressing HOLD key on the instrument.
The vertical ranges available in GMM displays vary with the measurement being graphed, and generally cover the
possible output range of the measurement.
The time ranges available for GMM displays range from 5 sec. to 24 hrs. per display.
Auto-Power-Off will not occur during the GMM mode, but to graph for periods of 5 min and longer, operate the
instrument from external power because operating endurance on internal power is limited to about 4 hours with fresh
batteries.
5-8 5-9
Testing Resistance, Diode, and Continuity Testing Frequency, Duty Cycle, or Pulse Width
Use this menu option to test resistance, diode forward voltage, and the continuity of wiring and connections. Connect
the test lead tip and test lead ground across the object to be tested.
GRAPHING MULTIMETER
GMM OHM FREQUENCY
CONTINUTY
OHM
Press to measure OPEN CLOSE DUTY CYCLE
resistance.
PULSE WIDTH
Press to test diodes. Press to test continuity of wiring and
connections.
If you select OPEN, the instrument beeps GMM FREQUENCY GMM DUTY CYCLE GMM PULSE WIDTH
when the tested connection is open. % ms % ms % ms
Hz Hz Hz
If you select CLOSE, it beeps when the
tested connection is closed.
OFL is displayed when the resistance is outside the instrument’s maximum range. This occurs when the resistance Press to test the signal P ress t o test the dut y cycle of the Press to test the pulse width of the
of the sensor is too high or the connection to the sensor is interrupted or open. frequency in Hz. signal. signal.
If you select , the duty cycle of the If you select , the width of the
To test a diode, the instrument sends a small current through the diode to test the voltage across it. Depending on negative-going pulse is displayed. negative-going pulse is displayed.
the type of diode, this voltage should be in the range from 300 to 600 mV. A diode that has an internal short will If you select , the duty cycle of the If you select , the width of the
display about 0 V. OFL is displayed when the diode is defective or when it is connected in reverse. If you are not positive-going pulse is displayed. positive-going pulse is displayed.
certain about the polarity of the diode, try the reverse connection. If this also displays OFL, the diode is defective. A
good diode must display OFL when connected in reverse.
Measuring RPM Testing Secondary Ignition Peak Volts, Burn Volts, and Burn Time
The instrument automatically scales and displays the waveform on the screen. Connect the Inductive Pickup to the
COM/TRIGGER input terminals and clamp the pickup probe on the spark plug wire close to the spark plug.
GRAPHING MULTIMETER
GMM RPM IGNITION PEAK VOLTS
Press to adjust the built-in RPM TRIG n DEFAULT REPEAT
1 720
4 step trigger levels. 2 SETUP TEST Press to start plotting a new graph IGNITION BURN VOLTS
Default is Level 2. as new samples are acquired.
IGNITION BURN TIME
Press to restore the default value
settings stored in VEHICLE DATA.
Press to decrease. Press to increase. GMM IGNITION PEAK VOLTS GMM IGNITION BURN VOLTS GMM IGNITION BURN TIME
INVERT REPEAT MAX/MIN INVERT REPEAT MAX/MIN INVERT REPEAT MAX/MIN
OFF TEST RESET OFF TEST RESET OFF TEST RESET
and keys are used to set the number of Spark Signal Pulses to the instrument per 720 (two crank shaft
revolutions). n = 1, 2, 3, 4, 5, 6, 8, 10, or 12
Press to invert the displayed ignition

waveform.
5-10 5-11
SINGLE cylinder waveform Testing Current
Use this menu option to test current with a current probe. (optional accessory)
SPARK VOLTAGE
GMM AMPERES
RANGE REPEAT
DC AC AC+DC 10 mV/A TEST
Press to measure DC current.
P ress to measure Press to select between
BURN VOLTAGE AC true rms current. 10 mV/A, and 100 mV/A.
BURN TIME
Press to measure AC+DC
true rms current.
Testing Injector Peak Volts and On Time Don’t forget to set the Current Probe to zero before using it for measurements.
Testing Temperature
Use this menu option to test temperature with a temperature probe. (optional accessory)
GRAPHING MULTIMETER
INJECTOR PEAK VOLTS GMM TEMPERATURE
P ress to selec t bet ween
REPEAT
INJECTOR ON TIME measuring degrees Celsius C F TEST
and degrees Fahrenheit.
GMM INJECTOR PEAK VOLTS GMM INJECTOR ON TIME
REPEAT MAX/MIN REPEAT MAX/MIN
TEST RESET TEST RESET
5.4 DUAL INPUT SCOPE OPERATION
Dual Input Scope

PEAK VOLTS Use the scope function if you want to simultaneously measure two waveforms - one on INPUT A and the other on
INPUT B.
Using Single and Dual Input Scope
Use SINGLE INPUT SCOPE if you want to use a single signal, INPUT B is turned off.
INJECTION PULSE WIDTH (ON TIME) Use DUAL INPUT SCOPE if you want to simultaneously measure two signals.
Testing Dwell
5.5 CHANGING THE VEHICLE DATA & INSTRUMENT SETUP
The test is done with the shielded test lead on INPUT A connected to the primary side of the ignition coil.
There are two groups of setups in the Main Menu.
GMM DWELL
VEHICLE DATA : Use this menu option to enter the correct vehicle data, such as the number of cylinders or cycles
VEHICLE DWELL MAX/MIN
DATA % RESET on the vehicle under test.
Press to select between readings in %,

degrees ( ) crankshaft rotation, or in ms.
5-12 5-13
INSTRUMENT SETUP : Use this menu option to set the following: DISPLAY OPTIONS MENU
• Optimal settings for display.
• Optimal settings for noise filter to each INPUT. USER LAST SETUP: You can change the Power-On display from VEHICLE DATA MENU (default) to the last
• Auto-Power-Off ON and OFF and adjusting Auto-Power-Off Time. display having been displayed just before the instrument was turned off.
• Language for menus and help text. CONTRAST: This setting, expressed as a percentage, determines the contrast ratio between display text or
• Scope Calibration graphics and the LCD background.
0 % is all white. 100 % is all black.
Changing Vehicle Data In practice, the percentage will be somewhere between 30 % and 80 %, to have a good
readable display.
If the vehicle data do not match with the vehicle under test, you could get incorrect test results and may not be able
You can also change contrast by pressing the LIGHT key and keeping it pressed until you
to select all available tests for this vehicle.
Because this menu is very important for the proper use of the instrument, it also appears at power-on as the start-up reach the desired contrast level.
display. GRATICULE: Can be set On or Off (default is On).
A dot type graticule assists in making visual voltage and timing measurements. The distance
between adjacent dots is one division. The graticule also allows you to easily compare wave
VEHICLE DATA VEHICLE DATA MENU forms between CH A and CH B and stored waveforms for timing and voltage differences.
CYLINDERS : 4 HORIZ TRIG POS: Horizontal Trigger Position can be set to three different horizontal locations (10 %, 50 %, or
CYCLES :4 90 %) on the display, depending on whether you want to see conditions that led up to the
BATTERY : 12 V trigger event, or those following it.
IGNITION : CONV
ACQUIRE MODE: Can be set to Peak Detect mode (default) or Normal mode.
• Peak Detect - This is the default mode to detect glitches and reduces the possibility of
CYLINDERS: 1, 2, 3, 4(default), 5, 6, 8, 10, or 12. Specifies the number of cylinders on the vehicle under test.
aliasing.
CYCLES: 2 or 4(default). Specifies a two-or four-stroke engine. • Normal - Use to acquire 480 points and display them at the SEC/DIV setting.
BATTERY: 12 V (default) or 24 V. Specifies battery voltage. < Key Points >
IGNITION: CONV (default), DIS, or DIESEL. If you probe a noisy square wave signal that contains intermittent and narrow glitches, the
waveform displayed will vary depending on the acquisition mode you choose.
Specifies the type of ignition system.
CONV (conventional) indicates systems using a distributor.
DIS (or EI) indicates Distributorless Ignition Systems.
DIESEL indicates ignition systems of Diesel engine.
Changing Instrument Setup
Normal Peak Detect

The next two topics describe each of the types of acquisition modes and their differences.
INSTRUMENT SETUP INSTRUMENT SETUP MENU
DISPLAY OPTIONS Peak Detect. Use Peak Detect acquisition mode to detect glitches as narrow as 1 µs and to
limit the possibility of aliasing. This mode is effective when at 10 µs/div or slower.
FILTER
AUTO POWER OFF
LANGUAGE
VERSION INFORMATION
SCOPE CALIBRATION
• Sample points displayed

Peak Detect mode displays highest and lowest acquired voltage in each interval.
5-14 5-15
Normal. Use Normal acquisition mode to acquire 480 points and display them at the SEC/DIV 5.6 FREEZING, SAVING, AND RECALLING SCREENS
setting.
Hold Mode
The HOLD key enables you to freeze the current display. This makes it possible to examine occasional waveform
anomalies and to stop the GMM mode at the end of a manual sweep test.
The instrument provides eight memory locations to which you can save the current screen along with its setup.
Press to freeze the current display and show the Function key Menu to save, recall, or to clear the memory.
HOLD indicator appears in the top right of the display when the HOLD key is pressed.
SAVE RECALL
RECALL
BACK SAVE CLEAR
MEMORY GLIT SN
• Sample points
Normal mode acquires a single sample point in each interval.
The maximum sample rate is 25 MS/s. At 10 µs and faster settings, this sample rate does not Press to resume measuring or to return to the previous display.
acquire 480 points. In this case, a Digital Signal Processor interpolates points between the
sampled points to make a full 480 point waveform record. Press to save the present screen in the next free memory location.
FILTER MENU: Can be set On or Off (default is Off) for each INPUT. • A message is displayed to tell you in which memory location the screen is saved.
• Off - Passes all signal components up to 5 MHz. The screen has been saved in screen memory 4.
• On - Passes signal components up to 2 KHz.
Turn on this option to reduce noises in scope displays and measurements. OK
AUTO POWER OFF MENU

AUTO POWER OFF: You can adjust the Auto-Power-Off time between 5 minutes and 120 minutes. • When all memory locations are filled from previous save actions, a message is displayed asking to overwrite a
memory location (press ) or to cancel saving (press ).
LANGUAGE MENU To save this screen, Overwrite memory 1?
LANGUAGE: This setting is used to select the local language or English for the information text display.
YES NO
This option is not available if only one language is implemented.
VERSION INFORMATION MENU

Press , if necessary, to clear all the memory locations.
VERSION INFORMATION: You can see the version number of current software.
Are you sure?
SCOPE CALIBRATION MENU
YES NO
SCOPE CALIBRATION: This setting is used to minutely calibrate the sc ope under the following operati ng
environments.
• When measuring in extremely hot or cold places.
• When the inner temperature of the scope was increased very greatly due to its long Press to recall the screen last saved in memory or press to recall the screen last saved in the Glitch
operation. Snare mode.
Press when SCOPE CALIBRATION is highlighted to activate this setting.
5-16 5-17
What’s more, by enabling the Auto Save option, each new event to be detected is automatically saved to Memory 1
The screen from memory 4 is displayed.
to Memory 4. By setting the Auto Save option, you can automatically fill up all four memories with the four most
OK recent unusual events.
Best of all, Glitch Snare operation is completely automatic. Trigger thresholds are calculated automatically based on
recent signal history. The measurement used as a basis for Glitch Snare operation is Period by default. Certain
COMPONENT TESTS use other measurements, and some tests disable Glitch Snare when it is inappropriate.
• Press to remove the message and the following Function Key Labels will be displayed on the screen. Glitch Snare is most useful with continuous AC or digital signals where the information is embedded in the signalís
MEMORY RECALL frequency, pulse width or duty factor.
SEARCH WFM
BACK 4 ERASE RUN To enable Glitch Snare operation, press the Glitch Snare function key in the Scope mode of the COMPO NENT
TESTS. If Glitch Snare is available for the current test, the instrument will display the Glitch Snare display in a line
along with a conventional scope display in a solid line for comparison. Vertical and horizontal settings for both
displays are matched.
• Use and to display the previous or the next screens in memory. These keys are effective only if
more than one screen has been saved in memory. The number indicates the recalled memory location. For example,
Press to select the displayed screen. The instrument activates the settings that are valid for the recalled
screen to test the input signal. COMPONENT TESTS
ACTUATORS
INJECTOR PFI/MFI
5.7 GLITCH SNARE OPERATION
Glitch Snare is a powerful combination of capabilities which enables you to reliable capture and display Actual Signal ACTUATOR INJECTOR PFI/MFI
Waveforms associated with elusive and unusual signals. REF WFM GLITCH KEYS
BACK OFF SNARE MOVE A
Glitch Snare combines real-time measurements with s pecially designed scope trigger facilities, monitoring
measurement results on an event by event basis and triggering on any result which deviates above or below the
norm by more than a present limit. The input signal is captured at the moment when a trigger event occurs.
Imagine the frequency graph from an ABS sensor with an occasional dropout due to an intermittent short in the
cable. As the wheel spins, the frequency output is stable until it briefly drops out due to the short. A graph of the ACTUATOR INJECTOR PFI/MFI
frequency shows a stable value until the short occurs. At that instant the graph show a sharp spike downward AUTO SAVE KEYS
BACK
OFF MOVE A
indicating that the frequency went to zero. Now imagine being able to set “trigger thresholds” above and below the
stable frequency value shown on the graph so that when the downward spike on the graph occurs, a trigger event is
generated. This is the essence of Glitch Snare operation.
When ordinary scopes try to detect dropouts and other sudden changes in continuous AC signals, the majority of the
signal is ignored because these instruments only display new waveforms at the rate of a few per second. Therefore, 5.8 TIPS FOR NOISE MANAGEMENT
it is not easy for them to capture and display the occasional glitch or dropout. And if an interesting event does
happen to be captured, it is soon overwritten with the next normal event, making detailed examination impossible. The instrument is very sensitive to spikes and other noise pulses which may be present on automotive signals. While
this capability can be valuable when tracking down glitch related problems, it can also obscure the signal you really
The Glitch Snare operation triggers only on abnormal signal conditions, which virtually guarantees you’ll catch the want to see in DC circuits such as power distribution.
first event to come along. The captured signal waveform remains displayed in the Glitch Snare display for you to
examine until it is overwritten by the next unusual event. If noise is obscuring the signals you want to see, try the following tips:
Using the Internal Battery Power

In general, noise pickup is minimized when you use this instrument on its internal battery power. Using the standard
Shielded Test Leads supplied will help in noise rejection
5-18 5-19
Noise Filter Function Key Labels
Turn on the Filter (INSTRUMENT SETUP menu) for the input channel you are using. This blocks frequencies above Manufacturer : Ford
2 kHz and should reduce ignition impulse noises and other noises of the short spike variety. OBD II CODE READER
BACK ERASE SCROLL MANUFAC LINK
Ground Connections Press to link the instrument with
Many sensors output signals are “single ended” meaning that a single output pin delivers the signal with being the vehicle’s PCM to retrieve any
referred to a ground pin also on the sensor. In order for the signal to be accurately delivered to the PCM, however, DTCs that are present in the PCM’s
Press to erase Diagnostic
both the signal and ground parts of the circuit should be sound. If a sensor output signal at the PCM appears to be Trouble Codes (DTCs) memory.
erratic or its level appears incorrect, check the signal at the output pins of the sensor (both signal and ground Press to select “Generic”(Generic is default) or a
connections). If the signal is correct, suspect the wire harness of either the signal or the ground side. Check for Press to scroll the LCD Display to
view the Diagnostic Trouble Codes vehicle manufacturer among GM, Ford, Chrysler,
voltage drops in both the signal and the ground paths between the sensor and the PCM. Toyota, and Honda to view the manufacturer’s
(when more than one DTC is present.)
Never trust that a chassis ground connection is the same as the PCM or the sensor ground. The ground continuity Manufacturer Specific DTC Definitions along with
can be disrupted by a missing strap or loose fastener easily. the Generic DTC Definitions.
Vehicles Covered
5.9 OBD II CODE READER MODE
• The OBDII Code Reader mode is designed to work on all OBD II compliant vehicles. All 1996 and newer vehicles
If you are having problems with your vehicle and only want to know if any Diagnostic Trouble Codes are present in (cars and light trucks) sold in the States are OBDII compliant by Federal Law; this includes all Domestic, Asian,
the vehicle’s computer system, use this instrument as an OBDII Code Reader in order to retrieve the codes. The and European vehicles.
codes retrieved, and their definitions, will give you valuable information and a starting point from which to proceed to • Some 1994 and 1995 vehicles are OBD II compliant. You can check this through the Vehicle Emissions Control
the next step. Once the codes have been retrieved, you can diagnosis the particular problem area in depth using Information (VECI) label located under the hood or by the radiator of most vehicles. If the vehicle is OBD II
SCOPE or GMM mode of this instrument or vice versa. compliant, the label will state “OBD II Certified”. You can also check this to see that the vehicle has a “common”
This instrument works as a simple OBD II Code Reader when entering into the Code Reader mode by using the sixteen-pin Data Link Connector (DLC) because the U.S. Government Regulations require that all OBD II
MAIN MENU. compliant vehicles must have a DLC.
Using OBD II Code Reader Mode Diagnostic Trouble Codes (DTCs)

Diagnostic Trouble Codes are codes that identify a particular problem area and are intended as a guide to the proper
service procedure described in the vehicle’s service manual.
OBD II CODE READER
NOTE
Do not replace parts or components based only on DTCs without first consulting
Making Connections the vehicle’s s ervice manual for proper testing procedures for that particular
s ystem, circuit, or c omponent. Utilizing DTCs is only one part of all overall
Connect the instrument to the vehicle’s sixteen-pin DLC (Data Link Connector) using the standard OBDII cable diagnostic strategies.
supplied. The DLC usually located under the dash (instrument panel), within 12 inches (300 mm) of center of the
panel, on the driver side of most vehicles. It is easily accessible and visible from a kneeling position outside the Each DTC has a set of testing procedures, instructions, and flow charts that must
vehicle with the door open. be followed to confirm the exact location of the problem. This type of information is
found in the vehicle’s service manual.
NOTE
If the DLC cannot be located, consult the vehicle’s service manual for the location.
5-20 5-21
• OBD II DTC Example 6. To view additional DTCs (if more than one code is present), press the SCROLL key, as necessary, until all the
(P0231 - Fuel Pump Secondary Circuit Low) codes have been displayed.
¡á Whenever the SCROLL function is used, the communication link with the vehicle’s computer disconnects. To
Identifies the “main P 0 2 3 1 Identifies what section reestablish communication, press the LINK key again.
system” where the
fault originated: of the system is
B - Body malfunctioning NOTE
C - Chassis If the instrument is relinked to a vehicle to retrieve codes, any prior codes in it’s
P - Powertrain Identifies the system where the problem is located: memory are automatically cleared.
U - Network 1 - Fuel and Air Metering
2 - Fuel and Air Metering (injector circuit malfunction only) • Erasing DTCs
Identifies the “type” 3 - Ignition System or Misfire
NOTE
of code: 4 - Auxiliary Emission Control System When the ERASE function is used to erase the DTCs from the vehicle’s computer,
0 - Generic 5 - Vehicle Speed Control and Idle Control System “Freeze Frame” data and manufacturer specific enhanced data are also erased.
1 - Manufacturer 6 - Computer Output Circuits If you plan to bring the vehicle to a repair shop, do not erase the codes.
Specific 7 - Transmission
8 - Transmission 1. Press the ERASE key. The LCD display will indicate “SURE” for your confirmation.
2. If you do not wish to continue erasing the codes, press the LINK key to return to the code retrieval function.
• DTC Retrieval Procedure
3. If you wish to continue erasing codes from the vehicle’s computer, press the ERASE key.
When “DONE” appears, all retrieval information, including DTCs, has been cleared from the vehicle’s computer
NOTE
memory.
Fix any k nown mechanical problems before performing any test. Loose or
damaged hoses, wiring or electrical connectors may, in some instances, cause a
DTC Definitions
“false” fault code.
The instrument will show both Generic Diagnostic Trouble Code Definitions and Manufacturer Specific Diagnostic
1. Turn the ignition off.
Trouble Code Definitions for the following vehicles along with the Codes.
2. Connect the standard OBD II cable connector to the vehicle’s DLC.
• OBD II Powertrain “GENERIC (P0XXX)” Diagnostic Trouble Codes:
The cable connector is keyed and will only fit one way.
OBDII Generic DTCs and their definitions apply to all makes and models of import and domestic vehicles that are
3. Turn the instrument on and select the OBD II Code Reader mode. OBD II COMPLIANT.
The Vehicle icon should display at this time to acknowledge a good power connection. If the icon is not
• OBD II Powertrain “MANUFACTURER SPECIFIC (P1XXX)” Diagnostic Trouble Codes: OBD II Manufacturer
displayed, recheck the cable connection.
Specific DTCs and their definitions apply only to vehicles produced by the specific manufacturers (GM, Ford,
4. Turn the ignition on. Do not start the engine. Chrysler, Toyota, and Honda).
5. Press the LINK function key. The LCD will display “READ”. NOTE
After 4–5 seconds, the instrument will display any DTCs that are in the vehicle’s computer memory and their OBD II is an evolving system so new codes and their definitions will be added as
Definitions. the sy stem matures. Always consult the vehic le’s serv ice manual for code
¡á If no codes are present in the vehicle’s computer memory, a “0” will be displayed. The instrument is capable definitions not provided by this instrument.
of retrieving and holding in memory up to 32 codes, for immediate or later viewing. For Manufacturer Specific Code Definitions not provided by this instrument and/or
¡á The instrument will automatically relink to the vehicle’s computer every 15 seconds to refresh the data being Body, Chassis, and Network DTC definitions, consult the vehicle service manual.
retrieved. When data is being refreshed, a single beep will sound, and “READ” will be shown on the LCD
display for approximately 5–6 seconds. The instrument will keep repeating as long as the instrument is in
communication with the vehicle’s computer.
¡á If the code retrieved is a pending code, the PENDING icon will show on the LCD display, but its Definition will
not show on the LCD display.
5-22 5-23
Appendix: About OBD II System • Enabling Criteria
Each Monitor is specifically designed to monitor the operation as well as to run diagnostic tests on a specific part
of the vehicle’s emissions system (such as EGR system, oxygen sensor, catalytic converter, etc.). “Enabling
OBD II System Objectives Criteria (a set of conditions or driving prodedures)” are required before the vehicle’s computer (PCM) can
command a Monitor to run the diagnostic tests on a particular part of the emissions system. The Enabling Criteria
The Main Objectives of the OBD II System are: vary for each Monitor.
For example, some Monitors only require the ignition key to be turned “on”, but others might require a set of
• To detect the degradation and/or failure of an emissions-related component or system that could cause emissions complex procedures, such as starting the vehicle when cold, bringing it to operating temperature, then driving the
to exceed by 1.5 times the Federal Test Procedure (FTP) standard. vehicle under specific conditions (accelerating, cruising, decelerating, etc.) before the Monitor can run and
complete its diagnostic testing on its associated part of the emissions system.
• To expand monitoring of the emissions-related system. This includes a set of computer run diagnostics called
Monitors.
• Trip or Trip Drive Cycle
Monitors perform diagnostics and testing to verify that all emissions-related components and/or systems are
operating correctly within the manufacturer’s specifications. A “Trip” for a particular Monitor is a drive cycle where the vehicle is driven in such a way that all the Enabling
Criteria for that Monitor are met. The “Trip” or “ Trip Drive Cycle”” for a particular Monitor begins when the ignition
• To equip a Diagnostic Link Connector (DLC) that is common (the same shape and size) for all vehicles. key is turned “on” and it is considered to have successfully completed when all the Enabling Criteria for that
particular Monitor were met by the time when the ignition key is turned “off”. The “Trip Drive Cycle” for each
• To have all vehicle manufacturers utilize a common code number, code definition, and language to describe a
individual Monitor will vary since each Monitor is designed for a different part of the engine or emissions system.
particular fault. Before OBD II, each vehicle manufacturer used their own code number, code definition, and
language to describe the same fault.
• OBD II Drive Cycle
• To expand the operation of the Malfunction Indicator Lamp (MIL). An OBD II Drive Cycle is an extended set of driving procedures considering the various types of driving conditions
encountered in real life such as starting the vehicle when it is cold, cruising, accelerating, decelerating, etc.. An
NOTE: In the past, the MIL has been referred to as a “check Engine” or “Service Engine Soon” light.
OBD II Drive Cycle begins when the vehicle is first turned on (when cold) and ends when the vehicle has been
• To have standardization of communication procedures and protocols between the diagnostic equipment (Scan driven in such a way as to have all the Enabling Criteria met for all it’s applicable Monitors.
Tools, Code Readers, etc.) and the vehicle’s on-board computer. Not all driving trips qualify as an OBD II Drive Cycle. Only those trips, that provide the Enabling Criteria for all
Monitors applicable to the vehicle, qualify as an OBD II Drive Cycle.
OBD II Drive Cycle requirements and procedures for all Monitors vary from one model of vehicle to another.
OBD II Terminology Vehicle manufacturers set these procedures.
• PCM(Powertrain Control Module) • Warm-up Cycle

The PCM is the OBD II accepted term for the vehicle’s “on-board computer”. The PCM controls the engine A Warm-up Cycle is defined as vehicle operation (after an engine off period) where the engine temperature rises
management and emissions systems as well as plays an active role in controlling the powertrain(transmission) from 40 F (22 C) to 160 F (70 C) after the vehicle was first started.
operation. Most PCMs have the ability to communicate with other vehicle computers. The PCM uses warm-up cycles as a counter to automatically erase a specific code and pertinent data from its
memory when no faults (specific to the original problem) are detected within a specified number of warm-up
• Monitor cycles.
Monitors are a set of “diagnostic strategies(instructions)” programmed into the PCM. The PCM executes these
special programs to run diagnostic tests and to monitor the operation of the vehicle’s emissions -related
components or systems in order to ens ure they are operating correctly within the vehicle’s manufacturer DTCs and MIL Status
specifications. Currently, there are eleven OBD II Monitors defined and required by the Environmental Protection
Agency (EPA), but Not all Monitors are supported by all vehicles. When the PCM detects a failure on an emissions-related component or system, OBD II regulations require that the
PCM’s diagnostic program assign a DTC that identifies the system or the part of the system where the fault was
• Monitor Has/Has Not Run detected. The diagnostic program is also required to store the code in the computer’s memory, to record a “Freeze
The terms “Monitor has run” or “Monitor has not run” are used in this manual. “Monitor has run” means the PCM Frame” of conditions present when the fault was detected, and to command the MIL “on” (some faults require
has executed a particular Monitor to perform the required diagnostic testing on a system to ensure the system is detection for two consecutive “trips” before the MIL is turned on).
operating correctly within factory specifications. “Monitor has not run” means the PCM has not yet executed that There are two categories of DTCs utilized for emissions-related faults: Type A and Type B. Type A codes are One
particular Monitor to perform diagnostic testing on its associated part of the emissions system. Trip DTCs; Type B codes are usually Two Trip DTCs.
5-24 5-25
When a Type A DTC is detected on the First trip, the following events take place: OBD II Monitors
• The computer activates or commands the MIL “on” immediately when the failure is first detected.
To verify the correct operation of the various emissions-related components and systems, a diagnostic program
• If the detected failure causes a severe misfire that may cause damage to the catalytic converter, the MIL will (containing several procedures and diagnostic strategies) was designed and installed in the on-board computer.
“flash” once per second and will continue flashing as long as the severe misfire exists. If the condition that could Each program is developed to monitor the operation of, and run Diagnostic Tests on, a specific emissions-related
cause the damage is no longer present, the MIL will revert to a “steady on” condition. component or system to ensure the system is operating correctly within the manufacturer’s specifications. On OBD II
systems, these procedures and diagnostic strategies are called “Monitors”.
• A DTC is saved in the computer’s memory for later retrieval.
Currently, there are eleven OBD II Monitors defined and required by the U.S. Environmental Protection Agency
• A “Freeze Frame (Snap Shot)” of the conditions present in the engine or emissions system at the instant the MIL (EPA), but not all monitors are supported by all vehicles. Monitor operation is either “continuous” or “non-
was commanded “on” is recorded and saved in the computer’s memory for later retrieval. This information shows continuous” depending upon the specific monitor.
fuel system status (closed loop or open loop), engine load, coolant temperature, fuel trim value, MAP vacuum,
engine RPM, and DTC Priority. Continuous Monitors
When a Type B DTC is detected on the First Trip, the following events take place: Three Monitors are designed to continuously monitor their associated components and/or systems for proper
operation. Continuous Monitors run continuously when the engine is in operation.
• The computer sets a “Pending” DTC, but the MIL is not commanded “on” at this time, and no “Freeze Frame” data
is recorded. The Pending DTC is stored in the computer’s memory for later retrieval. The continuous Monitors are:
• Comprehensive Component Monitor (CCM)
• If the failure is detected on the second consecutive trip, the MIL is commanded “on” and “Freeze Frame” data is
recorded and stored in the computer’s memory. • Misfire Monitor
• Fuel System Monitor
• If the failure is no longer detected on the second consecutive Trip, the Pending DTC is erased from the
computer’s memory. Non-Continuous Monitors
The MIL will stay lighted on Type A and Type B codes until one of the following conditions occurs: The other eight Monitors are Non-Continuous Monitors. They perform and complete their Diagnostic Testing once
per trip.
• If the conditions that caused the MIL to illuminate are no longer present for the next three consecutive trips, the
PCM will automatically command to turn the MIL “off” (if no other emissions-related faults are present). However, The Non-Continuous Monitors are:
the DTCs will stay in the computer’s memory for 40 warm-up cycles (80 warm-up cycles for fuel and misfire faults)
• Oxygen Sensor Monitor
and will automatically erase if the associated specific fault is not detected again during that period of time.
• Oxygen Sensor Heater Monitor
• Misfire and fuel system faults require three “similar conditions” Trips before the MIL is turned “off”. “Similar • Catalyst Monitor
Conditions” Trips are trips where the engine load, RPM, and temperature are similar to the conditions present
when the fault was first detected. • Heated Catalyst Monitor
• EGR System Monitor
NOTE: Freeze Frame data and manufacturer specific enhanced data (besides the DTCs) also stay in the computer’s • EVAP System Monitor
memory after the MIL has been turned “off”. These data can only be retrieved by more sophisticated testing • Secondary Air System Monitor
equipment such as an OBD II Scan Tool.
• Air Conditioning (A/C) Monitor
• Erasing the DTCs from the computer’s memory can also turn the MIL off. If a Code Reader or a Scan Tool is used
to erase the DTCs, Freeze Frame data as well as other manufacturer specific enhanced data will also be erased.
5-26 5-27
OBD II Monitors Table Enhanced I/M
On OBD II systems, the I/M program is enhanced by requiring vehicles to meet stricter test standards. One of the
The current OBD II Monitors are listed in the table below.
tests instituted by the Federal Government is called I/M 240. On I/M 240, the vehicle under test is driven under
MONITOR A B C D E F different speeds and load conditions on a dynamometer for 240 seconds, while the v ehicle’s emissions are
measured.
Comprehensive 3 similar
continuous 1 2 1 40
Component Monitor conditions NOTE: Emissions tests vary depending upon the geographic or regional area in which the vehicle is registered. if the
Misfire Monitor 3 similar vehicle is registered in a highly urbanized area, the I/M 240 is probably the type of test required. If the vehicle is
continuous 1 2 1 80 registered in a rural area, then a basic no-load test will probably be required.
(Type 1 & 3) conditions
Misfire Monitor 3 similar
continuous 1 80 I/M Readiness Monitors
(Type 2) conditions
Fuel System 3 similar I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly
continuous 1 1 or 2 1 80 and are ready for Inspection and Maintenance testing.
Monitor conditions
Catalytic Converter State and Federal G overnments enacted Regulations, Procedures, and Emission Standards to ensure that all
once per trip 1 2 1 3 trips 40
Monitor emissions-related components and systems are constantly or periodically monitored, tested, and diagnosed
Oxygen Sensor whenever the vehicle is in operation. They also requires vehicle manufacturers to automatically detect and report
once per trip 1 2 1 3 trips 40 any problems or faults that may increase the vehicle’s emissions to an unacceptable level.
Monitor
Oxygen Sensor To comply with State and Federal Government regulations, vehicle manufacturers designed a series of special
once per trip 1 2 1 3 trips 40
Heater Monitor computer programs called “Monitors” which are programmed in the vehicle’s computer. Each of these Monitors is
specifically designed to constantly or periodically run tests and diagnostics on a specific emissions-related
Exhaust Gas
component or system to ensure their proper operation.
Recirculation once per trip 1 2 1 3 trips 40
Monitor
Each Monitor has a specific function to test and diagnose only its designated emissions-related component or
Evaporative system. The names of the Monitors describe which component or system each Monitor is designated to test and
Emissions Controls once per trip 1 2 1 3 trips 40 diagnose.
Monitor
Secondary Retrieving I/M Readiness Monitor Status Information
Air System once per trip 1 2 1 3 trips 40 The I/M Readiness Monitor Status indicates which of the vehicle’s Monitors have run and completed their diagnosis
Monitor and testing and which ones have not yet run and completed testing and diagnosis of their designated sections of the
vehicle’s emissions system.
Remarks:
A - Monitor Type (how often does the Monitor run; Continuous or Once per trip) • It is very important to know the Monitor status. For example, the Oxygen Sensor Monitor must perform its
diagnosis and testing before the working status of the oxygen sensor is known. The Oxygen Sensor Monitor
B - Number of trips needed, with a fault present, to set a Pending DTC
activates the oxygen sensor to monitor its function. If the function is within specifications, no further action is
C - Number of consecutive trips needed, with a fault present, to command the MIL “on” and store a DTC taken. If a fault is detected, the Monitor reports it by generating DTC(s) and illuminating the MIL on the dashboard.
D - Number of trips needed, with no fault present, to erase a Pending DTC
• When a vehicle first comes from the factory, all the Monitors will indicate a DONE status, which means that all
E - Number and type of trips or drive cycles needed, with no fault present, to turn the MIL off.
Monitors have run and completed their diagnostic testing. The DONE status will remain in the computer’s memory
F - Number of warm-up periods needed to erase the DTC from the computers memory after the MIL is turned off indefinitely unless the DTCs are erased or the vehicle’s computer memory is cleared.
Inspection and Maintenance (I/M) Using the I/M Readiness Monitor Status to Confirm a Repair
• I/M is an Inspection and Maintenance program legislated by the Government to meet federal clean-air standards.
The Monitor Status function can be used (after a fault has been repaired) to confirm that the repair has been done
• The program requires that a vehicle to be taken periodically to an Emissions Station for an “Emissions Test” or correctly and/or to check for the Monitor RUN status.
“Smog Check”, where the emissions-related components and systems are inspected and tested for proper
1. Using retrieved DTC(s) and code definitions, repair the fault or faults following manufacturer’s repair procedures.
operation.
5-28 5-29
2. After the fault or faults have been repaired, connect the Instrument (in Code Reader mode) to the vehicle’s DLC to 6. AUTOMOTIVE DIAGNOSTICS & APPLICATIONS
erase the code or codes from the vehicle’s computer memory. (Write the codes down on a piece of paper for
reference before erasing them.)
6.1 COMPONENT TESTS
3. After erasing the codes, most of the Monitor icons on the Instrument’s LCD will be flashing. Leave the Instrument
connected to the vehicle and perform a Trip Drive Cycle for each “flashing” Monitor.
Preset Operation
NOTE: Continuous Monitors (Misfire, Fuel, and Comprehensive Component Monitors) run continuously and their
icons will always be on solid, even after the erase function is performed. The instrument provides predefined setups for a variety of vehicle sensors and circuits. To choose a preset test,
select COMPONENT TESTS from the MAIN MENU. From the resulting menu, select a test group:
¡á Each DTC is associated with a specific Monitor. (Consult the vehicle¡¯s service manual to identify the Monitor (or • SENSORS
Monitors) associated with the faults that were repaired. Follow the manufacturer¡¯s procedures to perform a Trip • ACTUATORS
Drive Cycle for the appropriate Monitors. • ELECTRICAL
¡á Perform a Trip Drive Cycle for the appropriate Monitor or Monitors, while observing the Monitor icons on the • IGNITION
Instrument’s LCD.
Then select a specific test from those listed. Each test places the instrument in a configuration best suited to display
WARNING : When performing a Trip Drive Cycle, ALWAYS have a second person help you. Trying to drive signals for the chosen device or circuit. Once a test has been selected, you can obtain some useful reference
and observe the Instrument’s LCD at the same time is dangerous and could cause a serious traffic accident. informations specific to that test at any time by pressing the HELP key as previously described.
In some cases there are more than one test for a particular device. If you are not sure which test to use, the
4. When a Monitor’s Trip Drive Cycle is performed properly, the Monitor icon will change from a “flashing” to a “solid”
condition, indicating that the Monitor has run and completed it’s diagnostic testing. descriptions to the tests in the following sections would help you decide.
After the Monitor has run, When you want to test a device for which no test is provided, choose a test for a similar device. For example, to test
¡á If the MIL on the vehicle’s dash is not illuminated and no codes associated with that particular Monitor are a temperature sensor not listed, try the Fuel Temp Sensor test. Or choose SCOPE from the MAIN MENU and
present in the vehicle’s computer, the repair was successful. configure the instrument manually as needed.
¡á If the MIL on the dash illuminates and/or a DTC associated with that Monitor is present in the computer, the After you chose a preset test, you may change most instrument settings as needed to get a better look at the signal.
repair was unsuccessful. Consult the vehicle’s service manual and recheck the repair procedures. You can even change the display type between SCOPE mode and GMM mode.
Retrieving I/M Readiness Monitor Status

If the Instrument is being used to retrieve I/M Readiness Monitor Status, follow the DTC retrieval procedures. 6.2 SENSOR TESTS
• If a Monitor icon on the Instrument’s LCD is on Solid, it indicates the associated Monitor has run and completed
SENSOR TESTS MENU SENSOR TESTS MENU
its diagnostic testing.
ABS Sensor (Mag) CMP Hall
• If a Monitor icon is Flashing, it indicates the associated Monitor has not yet run and completed its diagnostic COMPONENT TESTS O2S Sensor (Zirc) CMP Optical
testing. Dual O 2 Sensor VSS Magnetic
SENSORS ECT Sensor VSS Optical
• If all the Monitor icons are Solid and DONE is also displayed on the LCD, it indicates that all the Monitors that are Fuel Temp Sensor MAP Analog
applic able to the vehicle under test have run and completed their diagnostic testing and the I/M Monitor IAT Sensor MAP Digital
Readiness is completed. Knock Sensor MAF Analog
TPS Sensor MAF Digi Slow
NOTE: When DTCs are erased from the vehicle’s computer memory, the I/M Readiness Monitor Status program CKP Magnetic MAF Digi Fast
resets status of all the Monitors to a not run (“flashing”) condition. To set all of the Monitors to a DONE status, an CKP Hall MAF Karman-Vrtx
OBD II Drive Cycle must be performed. Consult your vehicle’s service manual for information on how to perform an CKP Optical EGR (DPFE)
OBD II Drive Cycle for the vehicle under test. CMP Magnetic
5-30 6-1
ABS Sensor-Magnetic • Troubleshooting Tips
If the amplitude is low, look for an excessive air gap between the trigger wheel and the pickup.
• Theory of Operation
If the amplitude wavers, look for a bent axle.
ABS (Anti-lock Brake System) wheel speed sensors generate AC signals with frequency proportional to wheel
speed. The amplitude (peak to peak voltage) increases as the wheel speed increases and is greatly affected by air If one of the oscillations looks distorted, look for a bent or damaged tooth on the trigger wheel.
gap between the magnetic tip and the reluctor wheel. The ABS computer compares the frequencies and uses this
information to maintain wheel speeds while braking.
O2S Normal - Zirconia
This test shows the sensor’s raw output signal or the frequency proportional to wheel speed. The sensor’s output
signal should be continuous as long as the wheel rotates. Spikes or distortion of individual output pulses may
indicate occasional contact between the sensor and the reluctor wheel. • Theory of Operation
An O2 sensor provides an output voltage that represents the amount of oxygen in the exhaust stream. The output
• Symptoms voltage is used by the PCM to adjust the air/fuel ratio of the fuel mixture between a slightly Rich condition and a
ABS light on, no ABS signal generation slightly Lean condition.
A zirconia-type O2 sensor provides high output voltage (a Rich condition) and low output voltage (a Lean condition).
• Test Procedure
A titania-type O2 sensor changes resistance as the oxygen content of the fuel mixture changes. This results in a low
1. Connect the shielded test lead to the CH A input and connect the ground lead of the test lead to the sensor output voltage (from a Rich condition) and a high output voltage (from a Lean condition). Most Titania O2 sensors
output LO or GND and the test lead probe to the sensor output or HI. (Use a wiring diagram for the vehicle being are found on MFI (Multiport Fuel Injection) systems.
serviced to get the ABS control unit pin number, or color of the wire for this circuit.)
A voltage swing between 100 mV and 900 mV indicates that the O2 sensor is properly signalling PCM to control the
2. Drive vehicle or spin the wheel by hand to generate signal. fuel mixture.
When driving vehicle, back probe the connector leading to the sensor. Place the transmission in drive, and slowly
accelerate the drive wheels. • Symptoms [OBD II DTC’s : P0130 ~ P0147, P0150 ~ P0167]
If the sensor to be tested is on a drive wheel, raise the wheels off the ground to simulate driving conditions. Key
OFF, Engine OFF (KOEO). Feedback Fuel Control System’s (FFCS’s) no entering Closed Loop operation, high emissions, poor fuel economy.
3. Use the Glitch Snare mode to detect spikes and dropouts. • Test Procedure
4. Compare ABS sensors on all wheels for similarities. 1. Connect the shielded test lead to the CH A input and connect the ground lead of the test lead to the sensor
output LO or GND and the test lead probe to the sensor output or HI. (Get the color of the O2 signal wire or PCM
• Reference Waveform pin number from a wiring diagram.)
VEHICLE INFORMATION 2. Warm the engine and O2 sensor for 2-3 minutes at 2500 RPM, and let the engine idle for 20 seconds.
FREQ = 416 Hz YEAR : 1989
P-P = 3.00 V 3. Rev the engine rapidly five or six times in 2 second intervals from idle to Wide Open Throttle (WOT). Be careful
ABS wheel speed sensor MAKE : Acura
logged while driving 20 MPH not to overrev the engine. Engine RPM over about 4000 is not necessary. Just get good snap throttle accels and
MODEL : Legend
full decels.
ENGINE : 2.7 L
FUELSYS : Multiport Fuel Injection 4. Use the HOLD key to freeze the waveform on the display to check the maximum O2 voltage, minimum O2 voltage
PCM_PIN : Pos Grn Blu pin 13 and response time from Rich to Lean.
Neg Brn pin 18
STATUS : KOBD (Key On Driven)
RPM : 1200
ENG_TMP : Operating Temperature
VACUUM : 18 In. Hg
MILEAGE : 69050
Amplitude and Frequency increase with wheel speed. Output signal should be stable
and repeatable without distorted pulses.
6-2 6-3
• Reference Waveform • Symptoms [OBD II DTC’s : P0420 ~ P0424, P0430 ~ P0434]
VEHICLE INFORMATION Emissions test failure, poor fuel economy.

Example of good O2 waveform from property YEAR : 1995
operating TBI system at idle. Hash is normal. MAKE : Plymouth • Test Procedure
Avg. O 2 voltage = 526 mV
MODEL : Acclaim 1. Connect one shielded test lead to the CH A and the other test lead to the CH B. Connect the ground leads of
ENGINE : 2.5 L both test leads to the engine GND’s and one lead probe to the sensor 1 (upstream sensor) output or HI and the
FUELSYS : Throttle Body Fuel Injection other lead probe to the sensor 2 (downstream sensor) output or HI.
PCM_PIN : 41 BkGrn Wire
STATUS : KOER (Key On Running) 2. Run the engine until the O2 sensors are warmed to at least 600 ˚F (315 ˚C) in closed loop operation.
RPM : Idle 3. Run the engine at idle while increasing engine speed.
“Moderate Hash” ENG_TMP : Operating Temperature
This is normal VACUUM : 20 In. Hg 4. Use this test to check the efficiency of the catalytic converter.
MILEAGE : 4350
• Reference Waveform
The maximum voltage when forced Rich should be greater than 800 mV. The minimum
voltage when forced Lean should be less than 200 mV. The maximum allowable VEHICLE INFORMATION
response time from Rich to Lean should be less than 100 ms. Waveform logged about Downstream O 2 sensor voltage YEAR : 1990
40 seconds after startup. rises as converter heats up and MAKE : Lexus
begins to use excess oxygen to
burn HC and CO.
MODEL : LS400
NOTE ENGINE : 4.0 L
For a Titania-type O2 sensor, change the vertical range to 1 V/div. FUELSYS : Multiport Fuel Injection
PCM_PIN : 6 OXL1 BIK wire OXL2 24 Grn wire
STATUS : KOER (Key On Running)
• Troubleshooting Tips RPM : 2500
ENG_TMP : Warming UP
The response time increases by aging and poisoning of the O2 sensor.
VACUUM : 21 In. Hg
Peak to peak voltages should be at least 600 mV or greater with an average of 450 mV. MILEAGE : 79369
If the waveform is severely hashy, look for a misfire caused by Rich mixture, Lean mixture, ignition problem, vacuum
G ood O2 sensor’s output swing between 100 mV and 900 mV indicates that the O
leak to an individual cylinder, injector imbalance, or carboned intake valves.
sensor is properly signalling PCM to control the fuel mixture.
IMPORTANT: Don’t use a scan tool at the same time you are analyzing the O2 waveform on the instrument. The The fluctuations in the downstream sensor’s signal are much smaller than that of the
PCM may go into a different operating strategy when diagnostics are activated by the scan tool. the upstream sensor. As the catalytic converter “lights off” (or reaches operating
temperature) the signal goes higher due to less and less oxygen being present in the
exhaust stream as the catalyst begins to store and use oxygen for catalytic conversion.
Dual O2 Sensor
Many vehicles utilize dual O2 sensors within the Feedback Fuel Control System. Both O 2 sensors provide an output
voltage that present the amount of oxygen in the exhaust stream respectively before and after the catalytic
converter. The leading sensor signal is used as feedback for controlling the fuel mixture. The trailing sensor signal is
used by PCM to test efficiency of the catalytic converter. The signal amplitude from the trailing sensor will increase
when the efficiency of the catalytic converter declines over years. A good O2 sensor located downstream from the
catalyst should see much less fluctuations than its upstream counterpart during steady state operation. This is due to
the properly operating catalyst’s ability to consume oxygen when it is converting HC and CO, thus dampening the
fluctuations in the downstream sensor’s signal. That is, the difference in voltage amplitude from the sensors is a
measure for the ability of the catalyst to store oxygen for the conversion of harmful exhaust constituents.
6-4 6-5
• Troubleshooting Tips 4. Press the HOLD key to freeze the waveform on the display for closer inspection.
When a catalytic converter is totally deteriorated, the catalytic conversion efficiency as well as the oxygen storage 5. To measure resistance, disconnect the sensor before changing to the GMM mode and then connect the Ground
capability of the catalytic converter are essentially lost. Therefore, the upstream and downstream O2 sensor signals and CH A leads to the terminals on the sensor.
closely resemble one another on an inactive converter.
V V
B VEHICLE INFORMATION
B MAX = 3.26 V ECT Test from stone
MIN = 1.86 V YEAR : 1986
cold to operating temp.
MAKE : Oldsmobile
Stone
cold Thermostat opens MODEL : Toronado
A here here
A
ENGINE : 3.8 L
63.5 Dg.F
FUELSYS : Multiport Fuel Injection
PCM_PIN : C10 Yel wire
t t
Engine at
upstream sensor downstream sensor
PCM resistor operating RPM : 1500
A B A B switched in temp. here
↓ ↓ ↓ ↓ here
ENG_TMP : Warming Up
VACUUM : 18 In. Hg
MILEAGE : 123686
Catalytic Converter OK Catalytic Converter Efficiency
poor
• Troubleshooting Tips
Check the manufacturer’s specifications for exact voltage range specifications, but generally the sensor’s voltage
should range from 3 V to just under 5 V when stone cold, dropping to around 1 V at operating temperature. The
ECT (Engine Coolant Temperature) Sensor good sensor must generate a signal with a certain amplitude at any given temperature.
• Theory of Operation Opens in the ECT sensor circuit will appear as upward spikes to V Ref.
Most ECT sensors are Negative Temperature Coefficient (NTC) type thermistors. This means they are primarily two Shorts to ground in the ECT sensor circuit will appear as downward spikes to ground level.
wire analog sensors whose resistance decreases when their temperature increases. They are supplied with a 5 V V
Ref power signal and return a voltage signal proportional to the engine coolant temperature to the PCM. When this
instrument is connected to the signal from an ECT sensor, what is being read is the voltage drop across the sensor’s Fuel Temp Sensor
NTC resistor.
Typically, ETC sensor’s resistance ranges from about 100,000 ohms at -40 ˚F (-40 ˚C) to about 50 ohms at +266 ˚F
(+130 ˚C). Most Fuel Temperature (FT) sensors are Negative Temperature Coefficient (NTC) type thermistors. They are
primarily two wire analog sensors whose resistance decreases when their temperature increases. Some sensors
The ETC sensor signal is used by the PCM to control closed-loop operation, shift points, torque converter clutch
operation, and cooling fan operation. use their own case as a ground, so they have only one wire, the signal wire. They are supplied with a 5 V V Ref
power signal and return a voltage signal proportional to the temperature to the PCM. FT sensors usually sense the
• Symptoms [OBD II DTC’s: P0115 ~ P0116, P0117 ~ P0119] engine’s fuel temperature in the fuel rail. When this instrument is connected to the signal from a FT sensor, what is
being read is the voltage drop across the sensor’s NTC resistor.
No or hard start, high fuel consumption, emissions failure, driveability problems.
Typically, FT sensor’s resistance ranges from about 100,000 ohms at -40 ˚F (-40 ˚C) to about 50 ohms at +266 ˚F
• Test Procedure (+130 ˚C).
1. Backprobe the terminals on the ECT sensor with the CH A lead and its ground lead. • Symptoms [OBD II DTC’s: P0180 ~ P0184, P0185 ~ P0189]
2. Run the engine at idle and monitor the sensor voltage decrease as the engine warms. (Start the engine and hold Hard start, poor fuel economy, driveability problems
the throttle at 2500 RPM until the trace goes across the screen.)
3. Set the time base to 50 sec/div to see the sensor’s entire operating range, from stone cold to operating
temperature.
6-6 6-7
• Test Procedure • Symptoms [OBD II DTC’s: P0110 ~ P0114]
1. Backprobe the terminals on the FT sensor with the CH A lead and its ground lead. Poor fuel economy, hard start, high emissions, tip-in hesitation
2. Start the engine and hold the throttle at 2500 RPM until the trace goes across the screen.
• Test Procedure
3. Set the time base to 50 sec/div to see the sensor’s entire operating range, from stone cold to operating 1. Backprobe the terminals on the IAT sensor with the CH A lead and its ground lead.
temperature.
2. When the IAT sensors are at engine operating temperature, spray the sensors with a cooling spray, a water
4. Press the HOLD key to freeze the waveform on the display for closer inspection. spray, or evaporative solvent spray and monitor the sensor voltage. Perform this test with the Key ON, Engine
5. To measure resistance, disconnect the sensor before changing to the GMM mode and then connect the Ground Off. The waveform should increase in amplitude as the sensor tip cools.
and CH A leads to the terminals on the sensor. 3. Press the HOLD key to freeze the waveform on the display for closer inspection.
• Reference Waveform 4. To measure resistance, disconnect the sensor before changing to the GMM mode and then connect the Ground
and CH A leads to the terminals on the sensor.
VEHICLE INFORMATION
MAX = 3.13 V
MIN = 2.66 V Engine warmed
YEAR : 1988 • Reference Waveform
up for 8 minutes MAKE : Nissan/Datsun
here VEHICLE INFORMATION
MODEL : 300 ZX non-turbo MAX = 3.26
ENGINE : 3.0 L MIN = 1.86
Key On Engine Off YEAR : 1986
“Spray” test Intake
FUELSYS : Multiport Fuel Injection Air Temp. Sensor MAKE : Oldsmobile
Engine stone
cold here PCM_PIN : 15 Yel wire MODEL : Toronado
STATUS : KOER (Key On Running) ENGINE : 3.8 L
RPM : 2000 Intake Air Temp sensor sprayed
ENG_TMP : Warming Up PCM_PIN : C11 Tan wire
Key On with brake cleaner here. As
VACUUM : 21 In. Hg Engine Off sensor tip cools, voltage STATUS : KOEO (Key On Engine Off)
here increases. RPM :0
MILEAGE : 57782
ENG_TMP : Ambient Temp.
VACUUM : 0 In. Hg
MILEAGE : 123686
should range from 3 V to just under 5 V when stone cold, dropping to around 1 to 2 V at operating temperature. The • Troubleshooting Tips
good sensor must generate a signal with a certain amplitude at any given temperature.
Opens in the FT sensor circuit will appear as upward spikes to V Ref. should range from 3 V to just under 5 V when stone cold, dropping to around 1 to 2 V at operating temperature. The
good sensor must generate a signal with a certain amplitude at any given temperature.
Shorts to ground in the FT sensor circuit will appear as downward spikes to ground level.
Opens in the IAT sensor circuit will appear as upward spikes to V Ref.
Shorts in the IAT sensor circuit will appear as downward spikes to ground level.
INTAKE AIR TEMP (IAT) Sensor
Knock Sensor
Most Intake Air Temperature (IAT) sensors are Negative Temperature Coefficient (NTC) type thermistors. They are
primarily two wire analog sensors whose resistance decreases when their temperature increases. They are supplied • Theory of Operation
with a 5 V V Ref power signal and return a voltage signal proportional to the intake air temperature to the PCM.
Some sensors use their own case as a ground, so they have only one wire, the signal wire. When this instrument is AC signal generating Knock Sensors are piezoelectric devices that sense vibration or mechanical stress (knock)
connected to the signal from an IAT sensor, what is being read is the voltage drop across the sensor’s NTC resistor. from engine detonation. They are quite different from most other AC signal generating automotive sensors that
sense the speed or position of a rotating shaft.
Typically, IAT sensor’s resistance ranges from about 100,000 ohms at -40 ˚F (-40 ˚C) to about 50 ohms at +266 ˚F
(+130 ˚C). Engine detonation resulting from overadvanced ignition timing can cause severe engine damage. Knock sensors
supply the PCM (sometimes via a spark control module) with Knock detection so the PCM can retard ignition timing
6-8 to prevent further Knocking. 6-9
Throttle Position Sensor (TPS)
Knock sensors generate a small AC voltage spike when vibration or a knock from detonation occurs. The bigger the
Knock or vibration, the bigger the spike. Knock sensors are usually designed to be very sensitive to the Knocking • Theory of Operation
frequencies (in 5 to 15 kHz range) of the engine block.
A TPS is a variable resistor that tells the PCM the position of the throttle, that is, how far the throttle is open, whether
• Symptoms [OBD II DTC’s: P0324 ~ P0334] it is opening or closing and how fast. Most throttle position sensors consist of a contact connected to the throttle
shaft which slides over a section of resistance material around the pivot axis for the movable contact.
No AC signal generation at all from Knock Sensors.
The TPS is a three wire sensor. One of the wires is connected to an end of the sensor’s resistance material and
• Test Procedure provides 5 V via the PCM’s V Ref circuit, another wire is connected to the other end of the resistance material and
provides the sensor ground (GND). The third wire is connected to the movable contact and provides the signal
1. Connect the CH A lead to the sensor output or HI and its ground lead to the engine block or the sensor wire output to the PCM. The voltage at any point in the resistance material is proportional to the throttle angle as sensed
labeled LO (if internally grounded). through the movable contact.
2. Test 1: With the Key On, Engine Running, put a load on the engine and watch the Scope display. The peak The voltage signal returning to the PCM is used to calculate engine load, ignition timing, EGR control, idle control
voltage and frequency of the waveform will increase with engine load and RPM increment. If the engine is and other PCM controlled parameters such as transmission shift points. A bad TPS can cause hesitation, idle
detonating or pinging from too much advanced ignition timing, the amplitude and frequency will also increase. problems, high emissions, and Inspection/ Maintenance (I/M) test failures.
Test 2: With the Key On, Engine Off, tap the engine block lightly near the sensor with a small hammer or a Generally, throttle position sensors produce just under 1 V with the throttle closed and produce just under 5 V with
ratchet extension. Oscillations will be displayed immediately following a tap on the engine block. The harder the the throttle wide open (WOT). The PCM determines the sensor’s performance by comparing the sensor output to a
tap, the larger the amplitude of the oscillations. calculated value based on MAP and RPM signals.
• Reference Waveform • Symptoms [OBD II DTC’s: P0120 ~ P0124, P0220 ~ P0229]
VEHICLE INFORMATION Hesitation, stall at stops, high emissions, I/M test failures, transmission shifting problems.
Typical Knock Sensor test. YEAR : 1993
Note signal goes above and below zero volts(AC). MAKE : Ford • Test Procedure
Logged during slight acceleration.
MODEL : F150 4WD Pickup
1. Connect the CH A lead to the output or signal circuit of TPS and its ground lead to the TPS’s GND.
ENGINE : 5.0 L
FUELSYS : Multiport Fuel Injection 2. With KOEO, slowly sweep the throttle from closed to the wide open position (WOT) and then the closed position
PCM_PIN : Neg-GND again. Repeat this process several times.
Pos-Pin23 Yel Red wire
STATUS : KOER (Key On Running) • Reference Waveform
RPM : Slightly Accelerate
ENG_TMP : Operating Temperature VEHICLE INFORMATION
VACUUM : 19 In. Hg MAX = 4.36 V YEAR : 1989
MIN = 880 mV
MILEAGE : 66748 Wide Open Throttle MAKE : Chevrolet
MODEL : 1500 Series Truck
• Troubleshooting Tips ENGINE : 5.0 L
FUELSYS : Throttle Body Fuel Injection
Knock sensors are extremely durable and usually fail from physical damage to the sensor itself. The most common
PCM_PIN : C13 DkBlu wire
type of Knock Sensor failure is not to generate a signal at all due to its physical damage, when the waveform stays Closed Throttle Closed Throttle
STATUS : KOEO (Key On Engine Off)
flat even if you rev the engine or tap on the sensor. In this case, check the sensor and the instrument connections;
RPM : 0
make sure the circuit is not grounded, then condemn the sensor.
VACUUM : 0 In. Hg
MILEAGE : 108706
6-10 6-11
• Troubleshooting Tips • Reference Waveform
Check the manufacturer’s specifications for exact voltage range. Generally, the sensor output should range from just VEHICLE INFORMATION
under 1 V at idle to just under 5 V at wide open throttle (WOT). There should be no breaks, spikes to ground or P - P = 13.7 V
YEAR : 1987
FREQ = 89.2 Hz
dropouts in the waveform. MAKE : Chrysler
MODEL : Fifth Avenue
Peak voltage indicates
WOT ENGINE : 5.2 L
Voltage decrease
FUELSYS : Feedback Carburetor
Dropouts on the slopes of the waveform indicate a PCM_PIN : 5 #1 Org wire + 9 #1 Blk wire
identifies enleanment
Voltage increase (throttle plate closing) short to ground or an intermittent open in the sensor’s STATUS : KOER (Key On Running)
identifies carbon track (resistance materials). RPM : 1400
enrichment.
The firs t 1/8 to 1/3 of the sensor’s carbon trac k ENG_TMP : Operating Temperature
usually wears out most because this portion is most VACUUM : 19 In. Hg
used while driving. Thus, pay particular attention to MILEAGE : 140241
DC offset indicates voltage the waveform as it begins to rise.
Minimum voltage indicates The amplitude and frequency increase with engine speed (RPM).
at key on, throttle closed.
closed throttle plate.
The amplitude, frequency and shape should be all consistent for the conditions (RPM,
(Defective TPS Pattern) etc.), repeatable (except for “sync” pulses), and predictable.
Generally, the oscillations may not be perfect mirror images of each other above and
below the zero level mark, but they should be relatively close on most sensors.
Magnetic Crankshaft Position (CKP) Sensor
• Theory of Operation • Troubleshooting Tips
The magnetic CKP sensors are AC signal generating analog sensors. They generally consist of a wire wrapped, soft Make sure the frequency of the waveform is keeping pace with engine RPM, and that the time between pulses only
bar magnet with two connections. These two winding, or coil, connections are the sensor’s output terminals. When a changes when a “sync” pulse is displayed. This time changes only when a missing or extra tooth on the reluctor
ring gear (a reluctor wheel) rotates past this sensor, it induces a voltage in the winding. A uniform tooth pattern on wheel passes the sensor. That is, any other changes in time between the pulses can mean trouble.
the reluctor wheel produces a sinusoidal series of pulses having a consistent shape. The amplitude is proportional to Look for abnormalities observed in the waveform to coincide with an engine sputter or driveability problem.
the rotating speed of the reluctor wheel (that is, the crankshaft or camshaft). The frequency is based on the
rotational speed of the reluctor. The air gap between the sensor’s magnetic tip and the reluctor wheel greatly affects Before assuring the sensor’s failure, when waveform abnormalities are observed, make sure that a chafed wire or
the sensor’s signal amplitude. bad wiring harness connector is not the cause, the circuit isn’t grounded, and the proper parts are spinning.
They are used to determine where TDC (Top Dead Center) position is located by creating a “synchronous” pulse
which is generated by either omitting teeth on the reluctor wheel or moving them closer together. Hall Effect CranKshaft Position (CKP) Sensor
The PCM uses the CKP sensors to detect misfire. When a misfire occurs, the amount of time it takes for a waveform
to complete its cycle increases. If the PCM detects an excessive number of misfires within 200 to 1000 crankshaft • Theory of Operation
revolutions, a misfire code (OBD II DTC) is set. These CKP sensors are classified as “CKP Sensors-Low Resolution” in industry.
The Hall CKP sensors are low resolution digital sensors which generate the CKP signal, that is a low frequency
• Symptoms [OBD II DTC’s: P0340 ~ P0349, P0365 ~ P0369, P0390 ~ P0394] (hundreds of Hz) square wave switching between zero and V Ref, from a Hall sensor.
No or hard start, intermittent misfire, driveability problems The Hall CKP sensor, or switch, consists of an almost completely closed magnetic circuit containing a permanent
magnet and pole pieces. A soft magnetic vane rotor travels through the remaining air gap between the magnet and
• Test Procedure the pole piece. The opening and closing of the vane rotor’s windows interrupt the magnetic field, causing the Hall
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. sensor to turn on and off like a switch - so some vehicle manufacturers call this sensor a Hall switch.
2. With KO ER (Key On, Engine Running), let the engine idle, or use the throttle to accelerate or decelerate the These sensors operate at different voltage levels depending on the vehicle manufacturers and deliver a series of
engine or drive the vehicle as needed to make the driveability, or emissions, problem occur. pulses as the shaft rotates.
They are used to switch the ignition and/or fuel injection triggering circuits on and off.
3. Use the Glitch Snare mode to catch dropouts or stabilize waveforms when a “sync” pulse is created. The PCM uses the Hall CKP sensors to detect misfire.
6-12 6-13
• Symptoms [OBD II DTC’s: P0340 ~ P0349, P0365 ~ P0369, P0390 ~ P0394] Optical CranKshaft Position (CKP) Sensor
Long cranking, poor fuel economy, emissions problem
• Test Procedure These CKP sensors are classified as “CKP Sensors - High Resolution” in industry.
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. The optical CKP sensors can sense position of a rotating component even without the engine running and their
pulse amplitude remains constant with variations in speed. They are not affected by electromagnetic interference
2. With KOEC (Key On, Engine Cranking), or with KOER, use the throttle to accelerate or decelerate the engine or
(EMI). They are used to switch the ignition and/or fuel injection triggering circuits on and off.
drive the vehicle as needed to make the driveability, or emissions, problem occur.
The optical sensor consists of a rotating disk with slots in it, two fiber optic light pipes, an LED, and a phototransistor
3. Use the Glitch Snare mode to catch dropouts or stabilize waveforms when a “sync” pulse is created.
as the light sensor. An amplifier is coupled to the phototransistor to create a strong enough signal for use by other
electronic devices, such as PCM or ignition module.
The phototransistor and amplifier create a digital output signal (on/off pulse).
VEHICLE INFORMATION
FREQ = 11.3 Hz YEAR : 1985
MAX = 8.33 V • Symptoms [OBD II DTC’s: P0340 ~ P0349, P0365 ~ P0369, P0390 ~ P0394]
MIN = 0.00 V MAKE : Volkswagen
MODEL : Jetta No or hard starts, stall at stops, misfires, poor fuel economy, emissions failure
Cranking test of Hall type (in dist.)
crankshaft position (CKP) sensor ENGINE : 1.8 L
FUELSYS : CIS Fuel Injection • Test Procedure
PCM_PIN : 9 GryWht wire 1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND.
STATUS : KOEC (Key On Cranking)
RPM : Cranking 2. With KOER (Key On, Engine Running), let the engine idle, or use the throttle to accelerate or decelerate the
ENG_TMP : Operating Temperature engine or drive the vehicle as needed to make the driveability, or emissions, problem occur.
VACUUM : 5 In. Hg
3. Use the Glitch Snare mode to catch dropouts or stabilize waveforms when a “sync” pulse is created.
MILEAGE : 105522
The amplitude, frequency, and shape should be all consistent in the waveform from • Reference Waveform
pulse to pulse. The amplitude should be sufficient (usually equal to sensor supply
voltage), the time between pulses repeatable (except for “sync” pulses), and the VEHICLE INFORMATION
FREQ = 2.27 kHz YEAR : 1989
shapes repeatable and predictable. Consistency is the key. MAX = 5.06 V Frequency Modulated signal.
MIN = -133 mV Frequency increases with MAKE : Mitsubishi
increasing engine RPM. Duty
cycle stays constant. MODEL : Montero
ENGINE : 3.0 L
The duty cycle of the waveform changes only when a “sync” pulse is displayed. Any other changes in duty cycle can PCM_PIN : 22 Blk wire at PCM
mean troubles. STATUS : KOER (Key On Running)
RPM : Idle
The top and bottom corners of the waveform should be sharp and voltage transitions of the edge should be straight ENG_TMP : Operating Temperature
and vertical. VACUUM : 20 In. Hg
Make sure the waveform isn’t riding too high off the ground level. This could indicate a high resistance or bad ground MILEAGE : 184066
supply to the sensor.
The amplitude, frequency, and shape should be all consistent in the waveform from
Although the Hall CKP sensors are generally designed to operate in temperatures up to 318 °F (150 °C), they can pulse to pulse. The amplitude should be sufficient, the time between pulses repeatable
fail at certain temperatures (cold or hot). (except for “sync” pulses), and the shapes repeatable and predictable. Consistency is
the key.
6-14 6-15
The duty cycle of the waveform changes only when a “sync” pulse is displayed. Any other changes in duty cycle can VEHICLE INFORMATION
mean troubles. PK - PK = 9.93 V
YEAR : 1989
FREQ = 33.1 Hz
The top and bottom corners of the waveform should be sharp. However, the left upper corner may appear rounded MAKE : Acura
on some of the higher frequency (high data rate) optical distributors. This is normal. MODEL : Legend
ENGINE : 2.7 L
Optical CKP sensors are very susceptible to malfunction from dirt or oil interfering with the light transmission through FUELSYS : Multiport Fuel Injection
the rotating disk. When dirt or oil enters into the sensitive areas of the sensors, no starts, stalls, or misfires can PCM_PIN : C3 OrgBlu
occur. STATUS : KOER (Key On Running)
RPM : Idle
Magnetic Camshaft Position (CMP) Sensor VACUUM : 20 In. Hg
MILEAGE : 69050
The amplitude and frequency increase with engine speed (RPM).
The magnetic CMP sensors are AC signal generating analog sensors. The generally consist of a wire wrapped, soft The amplitude, frequency and shape should be all consistent for the conditions (RPM,
bar magnet with two connections. These two winding, or coil, connections are the sensor’s output terminals. When a etc.), the time between pulses repeatable (except for “sync” pulses), and the shapes
ring gear (a reluctor wheel) rotates past this sensor, it induces a voltage in the winding. A uniform tooth pattern on repeatable and predictable.
the reluctor wheel produces a sinusoidal series of pulses having a consistent shape. The amplitude is proportional to
the rotating speed of the reluctor wheel (that is, the crankshaft or camshaft). The frequency is based on the
rotational speed of the reluctor. The air gap between the sensor’s magnetic tip and the reluctor wheel greatly affects
the sensor’s signal amplitude.
Make sure the frequency of the waveform is keeping pace with engine RPM, and that the time between pulses only
They are used to determine where TDC (Top Dead Center) position is located by creating a “synchronous” pulse
changes when a “sync” pulse is displayed. This time changes only when a missing or extra tooth on the reluctor
which is generated by either omitting teeth on the reluctor wheel or moving them closer together.
wheel passes the sensor. That is, any other changes in time between the pulses can mean trouble.
The PCM or ignition module uses the CMP sensors to trigger ignition or fuel injector events. The magnetic CMP and
Look for abnormalities observed in the waveform to coincide with an engine sputter or driveability problem.
CKP sensors are susceptible to Electromagnetic Interference (EMI or RF) from high voltage spark plug wires, car
phones or other electronic devices on the vehicle. This can cause a driveability problem or set a Diagnostic Trouble
Code (DTC).
Hall Effect Camshaft Position (CMP) Sensor
• Symptoms [OBD II DTC’s: P0340 ~ P0349, P0365 ~ P0369, P0390 ~ P0394]
Long cranking time, poor fuel economy, emissions failure
These CMP sensors are classified as “CMP Sensors - Low Resolution” in industry.
• Test Procedure The Hall CMP sensors are low resolution (accuracy) digital sensors which generate the CMP signal, that is a low
frequency (tens of Hz) square wave switching between zero and V Ref, from a Hall sensor.
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND.
2. With KOER (Key On, Engine Running), let the engine idle, or use the throttle to accelerate or decelerate the The Hall CMP sensor, or switch, consists of an almost completely closed magnetic circuit containing a permanent
engine or drive the vehicle as needed to make the driveability, or emissions, problem occur. magnet and pole pieces. A soft magnetic vane rotor travels through the remaining air gap between the magnet and
the pole piece. The opening and closing of the vane rotor’s window interrupts the magnetic field, causing the Hall
3. Use the Glitch Snare mode to catch dropouts or stabilize waveforms when a “sync” pulse is created. sensor to turn on the off like a switch - so some vehicle manufacturers call this sensor a Hall switch.
These sensors operate at different voltage levels depending on the vehicle manufacturers and deliver a series of
pulses as the shaft rotates.
They are used to switch the ignition and/or fuel injection triggering circuits on and off.
The PCM uses the Hall CMP sensors to detect misfire.
6-16 6-17
• Symptoms [OBD II DTC’s: P0340 ~ P0349, P0365 ~ P0369, P0390 ~ P0394] • Theory of Operation
Long cranking time, poor fuel economy, emissions failure These CMP sensors are classified as “CMP Sensors - High Resolution” in industry.
The optical CMP sensors are high resolution (accuracy) digital sensors which generate the CMP signal, that is a
• Test Procedure high frequency (hundreds of Hz to several kHz) square wave switching between zero and V Ref.
The optical CMP sensors can sense position of a rotating component even without the engine running and their
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. pulse amplitude remains constant with variations in speed. They are not affected by electromagnetic interference
2. With KOER (Key On, Engine Running), let the engine idle, or use the throttle to accelerate or decelerate the (EMI). They are used to switch the ignition and/or fuel injection triggering circuits on and off.
engine or drive the vehicle as needed to make the driveability, or emissions, problem occur. The optical sensor consis ts of a rotating disk with s lots in it, two fiber optic light pipes, and LED, and a
3. Use the Glitch Snare mode to catch dropouts or stabilize waveforms when a “sync” pulse is created. phototransistor as the light sensor. An amplifier is coupled to the phototransistor to create a strong enough signal for
use by other electronic devices, such as PCM or ignition module.
• Reference Waveform The phototransistor and amplifier create a digital output signal (on/off pulse)
VEHICLE INFORMATION • Symptoms [OBD II DTC’s: P0340 ~ P0349, P0365 ~ P0369, P0390 ~ P0394]
FREQ = 22.3 Hz
MAX = 7.33 V YEAR : 1986
Fixed Pulse Width signal. No or hard starts, stall at stops, misfires, poor fuel economy, emissions failure
MIN = -333 mV Frequency increases with MAKE : Oldsmobile
increasing engine RPM.
Camshaft makes one MODEL : Toronado • Test Procedure
rotation in between pulses. ENGINE : 3.8 L
FUELSYS : Multiport Fuel Injection 1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND.
PCM_PIN : K BrnWht wire at ignition module
STATUS : KOER (Key On Running) 2. With KOER (Key On, Engine Running), let the engine idle, or use the throttle to accelerate or decelerate the
RPM : 2500 engine or drive the vehicle as needed to make the driveability, or emissions, problem occur.
ENG_TMP : Operating Temperature 3. Use the Glitch Snare mode to catch dropouts or stabilize waveforms when a “sync” pulse is created.
VACUUM : 20 In. Hg
MILEAGE : 123686 • Reference Waveform
The amplitude, frequency, and shape should be all consistent in the waveform from VEHICLE INFORMATION
pulse to pulse. The amplitude should be sufficient (usually equal to sensor supply FREQ = 35.7 Hz YEAR : 1989
voltage), the time between pulses repeatable (except for “sync” pulses), and the shape MAX = 4.93 V Fixed Pulse Width signal.
MIN = 133 mV Frequency increases with
MAKE : Mitsubishi
repeatable and predictable. Consistency is the key. increasing engine RPM. MODEL : Montero
ENGINE : 3.0 L
PCM_PIN : 23 Red wire at PCM
• Troubleshooting Tips STATUS : KOER (Key On Running)
The duty cycle of the waveform changes only when a “sync” pulse is displayed. Any other changes in duty cycle can RPM : Idle
mean troubles. ENG_TMP : Operating Temperature
VACUUM : 20 In. Hg
The top and bottom corners of the waveform should be sharp and voltage transitions of the edge should be straight MILEAGE : 184066
and vertical.
The amplitude, frequency, and shape should be all consistent in the waveform from
Make sure the waveform isn’t riding too high off the ground level. This could indicate a high resistance or bad ground
pulse to pulse. The amplitude should be sufficient, the time between pulses repeatable
supply to the sensor.
(except for “sync” pulses), and the shapes repeatable and predictable. Consistency is
Although the Hall CMP sensors are generally designed to operate in temperatures up to 318 °F (150 °C), they can the key.
fail at certain temperatures (cold or hot).
Optical Camshaft Position (CMP) Sensor
6-18 6-19
The duty cycle of the waveform changes only when a “sync” pulse is displayed. Any other changes in duty cycle can VEHICLE INFORMATION
mean troubles. P - P = 6.93 V
YEAR : 1988
FREQ = 131 Hz
The top and bottom corners of the waveform should be sharp. However, the left upper corner may appear rounded MAKE : Nissan/Datsun
on some of the higher frequency (high data rate) optical distributors. This is normal. MODEL : 300 zx non-turbo
ENGINE : 3.0 L
Optical CMP sensors are very susceptible to malfunction from dirt or oil interfering with the light transmission through FUELSYS : Multiport Fuel Injection
the rotating disk. PCM_PIN : 12 Wht wire at the instrument cluster
When dirt or oil enters into the sensitive areas of the sensors, no starts, stalls, or misfires can occur. STATUS : KOBD (Key On Being Driven)
AC signal - Amplitude & Frequency
RPM : 1500
increase with vehicle speed. ENG_TMP : Operating Temperature
Magnetic Vehicle Speed Sensor (VSS) VACUUM : 20 In. Hg
MILEAGE : 57782
The amplitude and frequency increase with vehicle speed. Vehicle Speed Sensors
The vehicle speed sensors provides vehicle speed information to the PCM, the cruise control, and the speedometer. make waveforms whose shapes all look and behave v ery similar. Generally , the
The PCM uses the data to decide when to engage the transmission torque converter clutch lockup and to control oscillations (the ups and downs in the waveform) are very symmetrical at constant
electronic transmission shift levels, cruise control, idle air bypass, engine cooling fan, and other functions. speed.
The magnetic vehicle speed sensors are usually mounted directly on the transmissions or transaxles. They are two
wire sensors and AC signal generating analog sensors. They are very susceptible to Electromagnetic Interference
(EMI or RF) from other electronic devices on the vehicle. • Troubleshooting Tips
They generally consist of a wire wrapped, soft bar magnet with two connections. These two winding, or coil, If the amplitude is low, look for an excessive air gap between the trigger wheel and the pickup.
connections are the sensor’s output terminals. When a ring gear (a reluctor wheel) rotates past this sensor, it
If the amplitude wavers, look for a bent trigger wheel or shaft.
induces a voltage in the winding.
If one of the oscillations look distorted, look for a bent or damaged tooth on the trigger wheel.
A uniform tooth pattern on the reluctor wheel produces a sinusoidal series of pulses having a consistent shape. The
amplitude is proportional to the rotating speed of the reluctor wheel. The signal frequency is based on the rotational IMPORTANT: When troubleshooting a missing VSS signal, check the fuse first. If there is no power to the buffer,
speed of the reluctor. The air gap between the sensor’s magnetic tip and the reluctor wheel greatly affects the there will be no square wave output. If the fuse is good, check the sensor first than a buffer mounted
sensor’s signal amplitude. under the dash. If you have a sine wave coming from the sensor, but no square wave from the buffer,
don’t assume the problem is in the buffer; it may not be there because of a loose connector between
• Symptoms [OBD II DTC’s: P0500 ~ P0503] the sensor and the buffer.
Inaccurate speedometer, improper transmission shifting, problems affecting ABS and cruise control
• Test Procedure
Optical Vehicle Speed Sensor (VSS)
1. Raise the drive wheels off the ground and place the transmission in drive. • Theory of Operation
2. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. The optical vehicle speed sensors are usually driven by a conventional cable and are found under the dash. They
are digital sensors and are not affected by electromagnetic interference (EMI).
3. With KOBD (Key On, Being Driven), monitor the VSS output signal at low speed while gradually increasing the
speed of the drive wheels. They generally consist of a rotating disk with slots in it, two fiber optic light pipes, a light emitting diode, and a
phototransistor as the light sensor. An amplifier is coupled to the phototransistor to create a strong enough signal for
4. Use the Glitch Snare mode to detect spikes and dropouts. use by other electronic devices, such as the PCM or ignition module. The phototransistor and amplifier create a
digital output signal (on/off pulse).
Optical sensors are very susceptible to malfunction from dirt or oil interfering with the light transmission through the
rotating disk. When dirt or oil enters into the sensitive areas of the sensors, driveability problems can occur and
DTC’s can be set.
6-20 6-21
• Symptoms [OBD II DTC’s: P0500 ~ P0503] Analog Manifold Absolute Pressure (MAP) Sensor
Improper transmission shifting, inaccurate speedometer, problems affecting ABS and cruise control
• Test Procedure Almost all domestic and import MAP sensors are analog types in design except Ford’s MAP sensor. Analog MAP
sensors generate a variable voltage output signal that is directly proportional to the intake manifold vacuum, which is
1. Raise the drive wheels off the ground and place the transmission in drive.
used by the PCM to determine the engine load. They are primarily three wire sensors and are supplied with 5V V
2. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. Ref power, a ground circuit, and the signal output to the PCM.
3. With KOBD (Key On, Being Driven), monitor the VSS output signal at low speed (about 30 MPH) while gradually High pressure occurs when the engine is under a heavy load, and low pressure (high intake vacuum) occurs when
increasing the speed of the drive wheels. there is very little load. A bad MAP sensor can affect the air-fuel ratio when the engine accelerates and decelerates.
It may also have some effect on ignition timing and other PCM outputs. A bad MAP sensor or its hose can trigger
4. Use the Glitch Snare mode the detect spikes and dropouts. DTC’s for MAF, TP, or EGR sensors.
• Reference Waveform • Symptoms [OBD II DTC’s: P0105 ~ P0109]
VEHICLE INFORMATIONS Low power, stall, hesitation, excessive fuel consumption, emissions failure
FREQ = 19.2 Hz
MAX = 12.0 V Frequency Modulated Signal.
YEAR : 1984
MIN = 0.00 V Frequency increases with MAKE : Oldsmobile • Test Procedure
vehicle speed. MODEL : Toronado
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND.
ENGINE : 5.0 L
FUELSYS : Feedback Carburetor 2. Shut off all accessories, start the engine and let it idle in park or neutral. After the idle has stabilized, check the
PCM_PIN : 16 Brn wire idle voltage.
STATUS : KOBD (Key On Being Driven)
RPM : 1350 3. Rev the engine from idle to Wide Open Throttle (WOT) with a moderate input speed (this should only take about
ENG_TMP : Operating Temperature 2 seconds - don’t overrev the engine.)
VACUUM : 15 In. Hg 4. Let engine speed drop back down to idle for about two seconds.
MILEAGE : 52624
5. Rev the engine again to WOT (very quickly) and let it drop back to idle again.
The signal frequency should increase with increasing vehicle speed, but the duty cycle
should stay consistent at any speed. The amplitude, frequency, and shape should be 6. Press the HOLD key to freeze the waveform on the display for closer inspection.
all consistent in the waveform from pulse to pulse. The amplitude should be sufficient
(usually equal to sensor supply voltage), the time between pulses repeatable and the NOTE
shapes repeatable and predictable. It may be advantageous to put the sensor through its paces by using a handheld
vacuum pump to see that it generates the correct voltage at a specific vacuum.
The top and bottom corners of the waveform should be sharp and voltage transitions of the edge should be straight VEHICLE INFORMATIONS
MAX = 4.86 V slow Snap
and vertical. MIN = -133 mV accel. accel. YEAR : 1993
MAKE : Chevrolet
All of the waveforms should be equal in height due to the constant supply voltage to the sensor. MODEL : Suburban 1500
Make sure the waveform isn’t riding too high off the ground level. This could indicate a high resistance or bad ground ENGINE : 5.7 L
supply to the sensor. (Voltage drop to ground should not exceed 400 mV.)
Idle FUELSYS : Throttle Body Fuel Injection
PCM_PIN : B13 LtGrn wire at MAP sensor
Look for abnormalities observed in the waveform to coincide with a driveability problem or a DTC. STATUS : KOER (Key On Running)
RPM : Acceleration & Deceleration
Full
decel. ENG_TMP : Operating Temperature
0VACUUM : 3-24 In. Hg
MILEAGE : 55011
6-22 6-23
3. Make sure that the amplitude, frequency and shape are all present, repeatable, and consistent. Amplitude should
Check the manufacturer’s specifications for exact voltage range versus vacuum levels,
be close to 5 V.
and compare them to the readings on the display. Generally the sensor voltage should
Frequency should vary with vacuum. Shape should stay constant (square wave).
range about 1.25 V at idle to just under 5 V at WOT and close to 0 V on full
deceleration. High vacuum (around 24 In. Hg on full decel) produces low voltage 4. Make sure the sensor produces the correc t frequency for a given amount of vacuum, according to the
(close to 0 V), and low vacuum (around 3 In. Hg at full load) produces high voltage specification chart for the vehicle you are working on.
(close to 5 V).
5. Use the Glitch Snare mode to detect dropouts or unstable output frequency.
IMPORTANT: There are a few MAP sensors designed to do the opposite (high vacuum = high voltage). • Reference Waveform
Some Chrysler MAP sensors just stay at a fixed voltage when they fail, regardless of changes in
vacuum level. Generally 4 cylinder engines make nosier waveforms because their vacuum fluctuates VEHICLE INFORMATIONS
more between intake strokes. FREQ = 159 Hz YEAR : 1993
MAX = 5.06 V
MIN = -133 mV Ford digital MAP sensor
MAKE : Ford
Key On Engine Off (KOEO) MODEL : F150 4WD Pickup
• Troubleshooting Tips ENGINE : 5.0 L
A high voltage level indicates
high intake manifold pressure
PCM_PIN : 45 LtGrn Blk wire
HIGH ENGINE LOAD STATUS : KOEO (Key On Engine Off)
(low vacuum).
RPM : 0
LOW ENGINE LOAD ENG_TMP : Operating Temperature
As the throttle plate opens, VACUUM : 0 In. Hg
manifold pressure rises MILEAGE : 66748
(manifold vacuum lowers).
A low voltage level indicates Frequency decreases as vacuum increases. Look for pulses that are a full 5 V in
low intake manifold pressure amplitude. Voltage transitions should be straight and vertical. Voltage drop to ground
(high vacuum). should not exceed 400 mV. If the voltage drop is greater than 400 mV, look for a bad
ground at the sensor or the PCM.
Digital Manifold Absolute Pressure (MAP) Sensor • Troubleshooting Tips
• Theory of Operation A bad digital MAP sensor can produce incorrect frequencies, runted (shortened) pulses, unwanted spikes and
rounded off corners that could all have the effect of garbling “electronic communication”, thus causing a driveability
Ford’s digital MAP sensor is found on many Ford and Lincoln Mercury vehicles from the early 1980’s to well into the or emissions problem.
1990’s. This sensor produces a frequency modulated square wave whose frequency varies with the amount of
intake vacuum sensed. It generates about 160 Hz with no vacuum applied, and it generates about 105 Hz when it is
sensing around 19 In.Hg at idle. Check the manufacturer’s specs for the year, make and model for exact vacuum Analog Mass Air Flow (MAF) Sensor
versus frequency reference numbers. This is a three wire sensor, supplied with 5 V V Ref power, a ground circuit,
and the digital signal output pulses based on the amount of vacuum it senses. • Theory of Operation
• Symptoms [OBD II DTC’s: P0105 ~ P0109] There are two main varieties of analog MAF sensors; Hot Wire type and Vane type. Hot wire type MAF sensors use
heated-metal-foil sensing element to measure air flow entering the intake manifold. The sensing element is heated to
Low power, stall, hesitation, excessive fuel consumption, emissions failure about 170 ˚F (77 ˚C), above the temperature of incoming air. As air flows over the sensing element, it cools the
element, causing resistance to drop. This causes a corresponding increase in current flow, which causes supply
• Test Procedure voltage to decrease. This signal is seen by the PCM as a change in voltage drop (high air flow = high voltage) and is
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. used as an indication of air flow. The PCM uses this signal to calculate engine load, to determine the right amount of
fuel to be mixed with the air, and ignition timing, EGR control, idle control, transmission shift points, etc.
2. With the Key On, Engine Off (KOEO), apply different amounts of vacuum to the sensor using a handheld vacuum
pump.
6-24 6-25
Vane type MAF sensors, mainly, consist of a variable resistor (potentiometer) that tells the PCM the position of the • Troubleshooting Tips
vane air flow door. As the engine is accelerated and more air passes through the vane air flow sensor, the vane air
door is pushed open by the incoming air. The angle of the vane air flow door is proportional to the volume of air If overall voltage is low, be sure to check for cracked, broken, loose, or otherwise leaking intake air ducts.
passing by it. A vane type MAF sensor consists of a contact connected to the vane door which slides over a section
of resistance material that is places around the pivot axis for the movable contact. The voltage at any point in the IMPORTANT: 0.25 V can make the difference between a good sensor and a bad one, or an engine that is blowing
resistance material, as sensed through the movable contact, is proportional to the angle of the vane air door. black smoke and one that is in perfect control of fuel mixture.
However, because the sensor output voltages will vary substantially depending on vehicle engine
Overswing of the door caused by snap accelerations provides information to the PCM for acceleration enrichment.
[Many Toyotas are equipped with vane type MAF sensors operating opposite the above – their voltage is high when families, in some cases, this sensor can be difficult to diagnose definitively.
airflow is low.]
• Symptoms [OBD II DTC’s: P0100 ~ P0104] Digital Slow MAF (Mass Air Flow) Sensor
Hesitation, stall, low power, idle problems, excessive fuel consumption, emissions failure • Theory of Operation
• Test Procedure There are three main varieties of digital MAF sensors; Digital Slow type (output signals in the 30 to 500 Hz range),
Digital Fast type (output signals in the kHz range), and Karman Vortex type (which changes pulse width as well as
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. frequency). A digital MAF sensor receives a 5 V reference signal from the PCM and sends back a variable frequency
signal that is proportional to the mass of air entering the engine. The output signal is a square wave, in most cases,
2. Shut off all accessories, start the engine and let it idle in park or neutral. After the idle has stabilized, check the
with a full 5 V in amplitude. As the airflow increases, the frequency of the signal generated increases. The PCM uses
idle voltage.
these signals to calculate fuel injector ON time and ignition timing and also determines MAF sensor deterioration by
3. Rev the engine from idle to Wide Open Throttle (WOT) with a moderate input speed (this should only take about comparing the MAF signal to a calculated value based on MAP, TP, IAT, and RPM signals.
2 seconds – don’t overrev the engine).
Digital Slow MAF sensors can be found on early to mid 1980’s G M vehicles, and many other engine systems.
4. Let engine speed drop back down to idle for about two seconds. Generally, the older the MAF sensor, the slower the frequency it produces.
5. Rev the engine again to WOT (very quickly) and let it drop back to idle again. • Symptoms [OBD II DTC’s: P0100 ~ P0104]
6. Press the HOLD key to freeze the waveform on the display for closer inspection. Hesitation, stall, low power, idle problems, excessive fuel consumption, emissions failure
• Reference Waveform • Test Procedure
VEHICLE INFORMATIONS 1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND.
MAX = 4.12 V YEAR : 1993
MIN = 680 mV Snap 2. With the Key On, Engine Running (KOER), use the throttle to accelerate and decelerate the engine. Try different
slow accel. MAKE : Ford
RPM ranges while spending more time in the RPM ranges that correspond to the driveability problem.
accel. MODEL : Explorer
ENGINE : 4.0 L 3. Make sure that the amplitude, frequency and shape are all correct, consistent, and repeatable.
Idle PCM_PIN : 14 LtBlu Red wire 4. Make sure that the sensor generates the correct frequency for a given RPM or airflow rate.
STATUS : KOER (Key On Running) 5. Use the Glitch Snare mode to detect dropouts or unstable output frequency.
Full RPM : Acceleration and Deceleration
decel. ENG_TMP : Operating Temperature
VACUUM : 2-24 In. Hg
MILEAGE : 54567
Hot wire type MAF sensor voltage should range from just over 2 V at idle to just over 4
V at WOT, and should dip slightly lower than idle voltage on full deceleration.
Vane type MAF sensor voltage should range from about 1 V at idle to just over 4 V at
WOT and not quite back to idle voltage on full deceleration.
Generally, on non-Toyota varieties, high airflow makes high voltage and low airflow
makes low voltage. When the sensor voltage output doesn’t follow airflow closely, the
waveform will show it and the engine operation will be noticeably affected.
6-26 6-27
• Reference Waveform 4. Make sure that the sensor generates the correct frequency for a given RPM or airflow rate.
VEHICLE INFORMATIONS 5. Use the Glitch Snare mode to detect dropouts or unstable output frequency.
FREQ = 64.1 Hz YEAR : 1986
MAX = 4.93 V • Reference Waveform
MIN = 0.00 V MAKE : Oldsmobile
Frequency increases due to air
flow increase from snap accel. MODEL : Toronado
VEHICLE INFORMATIONS
ENGINE : 3.8 L FREQ = 6.57 kHz
FUELSYS : Multiport Fuel Injection MAX = 5.06 V YEAR : 1990
PCM_PIN : B6 Yel wire MIN = 0.00 V MAKE : Buick
STATUS : KOER (Key On Running) MODEL : Le Sabre
RPM : Snap Acceleration ENGINE : 3.8 L
Idle air flow here ENG_TMP : Operating Temperature
before snap accel. VACUUM : 0-24 In. Hg PCM_PIN : Yel wire
MILEAGE : 123686 STATUS : KOER (Key On Running)
RPM : 2500
Frequency stays constant when airflow is constant. Frequency increases as airflow ENG_TMP : Operating Temperature
increases from snap acceleration. VACUUM : 20 In. Hg
Look for pulses that are a full 5 V in amplitude. Voltage transitions should be straight MILEAGE : 103128
and vertical. Voltage drop to ground should not exceed 400 mV. If greater than 400
mV, look for a bad ground at the sensor or the PCM. Frequency stays constant when airflow is constant. Frequency increases as airflow
increases from snap acceleration. Look for pulses that are a full 5 V in amplitude.
Voltage transitions should be straight and vertical. Voltage drop to ground should not
• Troubleshooting Tips exceed 400 mV. If greater than 400 mV, look for a bad ground at the sensor or the
PCM.
Possible defects to watch for are runted (shortened) pulses, unwanted spikes, and rounded off corners that could all
have the effect of garbling an electronic communication, causing a driveability or emissions problem. The sensor
should be replaced if it has intermittent faults. NOTE
On some Digital Fast MAF sensors, such as the GM Hitachi sensor found on 3800
Buick V-6s, the upper left corner of the pulse is rounded off slightly. This is normal
Digital Fast MAF (Mass Air Flow) Sensor and doesn’t indicate a bad sensor.
Digital Fast type MAF sensors can be found on GM’s 3800 V-6 engine with the Hitachi sensor, Lexus models, and
many others. The Hitachi sensor has a square wave output in the 10 kHz range. Possible defects to watch for are runted (shortened) pulses, unwanted spikes, and rounded off corners that could all
Voltage level of square waves should be consistent and frequency should change smoothly with engine load and have the effect of garbling an electronic communication, causing a driveability or emissions problem. The sensor
speed. should be replaced if it has intermittent faults.
• Symptoms [OBD II DTC’s: P0100 ~ P0104]

Digital Karman-Vortex MAF (Mass Air Flow) Sensor
Hesitation, stall, low power, idle problems, excessive fuel consumption, emissions failure
• Test Procedure
Karman-Vortex type MAF sensors are usually manufactured as part of the air cleaner assembly. They are commonly
1. Connect the CH A lead to the sensor output or HI and its ground lead to the sensor output LO or GND. found on Mitsubishi engine systems. While most digital MAF sensors vary only their frequency with changes in
2. With the Key On, Engine Running (KOER), use the throttle to accelerate and decelerate the engine. Try different airflow rate, the Karman-Vortex type’s signal varies Pulse Width as well as Frequency with changes in airflow rate.
RPM ranges while spending more time in the RPM ranges that correspond to the driveability problem. As the airflow increases, the frequency of the signal generated increases.
3. Make sure that the amplitude, frequency and shape are all consistent, repeatable, and accurate. Karman-Vortex sensors differ from other digital MAF sensors during acceleration modes. During acceleration, not
only does the sensor’s frequency output increases, but also its pulse width changes.
6-28 6-29
• Symptoms [OBD II DTC’s: P0100 ~ P0104] Differential Pressure Feedback EGR (DPFE) Sensor
Hesitation, stall, low power, idle problems, excessive fuel consumption, emissions failure
• Test Procedure An EGR (Exhaust Gas Recirculation) pressure sensor is a pressure transducer that tells the PCM the relative
pressures in the exhaust stream passages and, sometimes, intake manifold. It is found on some Ford EEC IV and
1. Connect the CH A lead to the sensor output HI and its ground lead to the sensor output LO or GND.
EEC V engine systems.
2. With the Key On, Engine Running (KOER), use the throttle to accelerate and decelerate the engine. Try different
Ford calls it a PFE (Pressure Feedback EGR) sensor when the sensor outputs a signal that is proportional to the
RPM ranges while spending more time in the RPM ranges that correspond to the driveability problem.
exhaust backpressure.
3. Make sure that the amplitude, frequency, shape, and pulse width are all consistent, repeatable and accurate for
Ford calls it a DPFE (Differential Pressure Feedback EGR) sensor when the sensor outputs the relative difference in
any given operating mode.
pressure between intake vacuum and exhaust.
4. Make sure that the sensor generates the correct and steady frequency for a given RPM or airflow rate.
These are important sensors because their signal input to the PCM is used to calculate EGR flow. A bad EGR
5. Use the Glitch Snare mode to detect dropouts or unstable output frequency. pressure sensor can cause hesitation, engine pinging, and idle problems, among other driveability problems, and I/M
emission test failures.
The EGR pressure sensor is usually a three wire sensor. One wire supplies the sensor with 5 V via the PCM’s V Ref
circuit, another wire provides the sensor ground, and the third wire is the sensor’s signal output to the PCM.
FREQ = 69.4 Hz avg.
MAX = 5.06 V
YEAR : 1992 Generally, Ford’s DPFE sensors are found on late model 4.0 L Explorers and other vehicles and produce just under
MIN = 933 mV MAKE : Mitsubishi 1 V with no exhaust gas pressure and close to 5 V with maximum exhaust gas pressure.
Karman Vortex MAF sensor MODEL : Eclipse
during snap acceleration. ENGINE : 1.8 L NOTE
FUELSYS : Multiport Fuel Injection Ford’s PFE sensors produce 3.25 V with no exhaust back pressure increasing to
PCM_PIN : 10 GrnBlu wire about 4.75 V with 1.8 PSI of exhaust back pressure. O n properly operating
STATUS : KOER (Key On Running) vehicles the voltage won’t ever get to 5 V. PFE sensors can be found on many
RPM : Snap Acceleration Taurus and Sable models.
VACUUM : 3-24 In. Hg
MILEAGE : 49604 • Symptoms [OBD II DTC’s: P0400 ~ P0408]
Frequency increases as airflow rate increases. Pulse width (duty cycle) is modulated in Hesitation, engine pinging, idle problems, I/M emission test failure
acceleration modes.
Look for pulses that are a full 5 V in amplitude. Look for the proper shape of the • Test Procedure
waveform in terms of consistent, square corners, and consistent vertical legs. 1. Connect the CH A lead to the sensor output HI and its ground lead to the sensor output LO or GND.
2. Start the engine and hold throttle at 2500 RPM for 2–3 minutes until the engine is fully warmed up and the
• Troubleshooting Tips Feedback Fuel System is able to enter closed loop. (Verify this by viewing the O2 sensor signal, if necessary.)
Possible defects to watch for are runted (shortened) pulses, unwanted spikes, and rounded off corners that could all 3. Shut off A/C and all other accessories. Drive the vehicle under normal driving modes; start from dead stop, light
have the effect of garbling an electronic communication, causing a driveability or emissions problem. The sensor acceleration, heavy acceleration, cruise, and deceleration.
should be replaced if it has intermittent faults.
4. Make sure that the amplitude is correct, repeatable, and present during EGR conditions. The sensor signal
should be proportional to exhaust gas versus manifold vacuum pressures.
5. Make sure that all the hoses and lines to and from the intake manifold, EGR valve, and vacuum solenoid valve
are intact, and routed properly, with no leaks. Make sure the EGR valve diaphragm can hold the proper amount
of vacuum (check manufacturer’s specs.). Make sure that the EGR passageways in and around the engine are
clear and unrestricted from internal carbon buildup.
6. Press the HOLD key to freeze the waveform on the display for closer inspection.
6-30 6-31
• Reference Waveform Saturated Switch Type (MFI/PFI/SFI) Injector
VEHICLE INFORMATIONS • Theory of Operation

MAX = 1.86 V YEAR : 1994
MIN = 400 mV
MAKE : Ford The fuel injector itself determines the height of the release spike. The injector driver (switching transistor) determines
Ford EGR Differential Pressure most of the waveform features. Generally an injector driver is located in the PCM that turns the injector on and off.
Sensor logged during snap MODEL : Explorer
acceleration ENGINE : 4.0 L Different Kinds (Saturated Switch type, Peak-and-Hold type, Bosch type Peak-and-Hold, and PNP type) of injector
FUELSYS : Multiport Fuel Injection drivers create different waveforms. Knowing how to interpret injector waveforms (determining on-time, referencing
PCM_PIN : 27 BrnLtGrn wire peak height, recognizing bad drivers, etc.) can be a very valuable diagnostic talent for driveability and emission
STATUS : KOER (Key On Running) repair.
RPM : Snap Acceleration Saturated switch injector drivers are used primarily on multiport fuel injection (MFI, PFI, SFI) systems where the
Engine accelerated ENG_TMP : Operating Temperature
here injectors are fired in groups or sequentially. Determining the injector on-time is fairly easy. The injector on-time
VACUUM : 3-24 In. Hg begins where the PCM grounds the circuit to turn it on and ends where the PCM opens the control circuit. Since the
MILEAGE : 40045 injector is a coil, when its electric field collapses from the PCM turning it off, it creates a spike. Saturated Switch type
injectors have a single rising edge. The injector on-time can be used to see if the Feedback Fuel Control System is
As soon as the engine reaches the predetermined EGR requirement conditions, the
doing its job.
PCM will begin opening the EGR valve. The waveform should rise when the engine is
accelerated. The waveform should fall when the EGR valve closes and the engine
• Symptoms
decelerates. EGR demands are especially high during accelerations. During idle and
deceleration, the valve is closed. Hesitation, rough idle, intermittent stall at idle, poor fuel mileage, emissions test failure, low power on acceleration
• Test Procedure
1. Connect the CH A lead to the injector control signal from the PCM and its ground lead to the injector GND.
There should be no breaks, spikes to ground, or dropouts in the waveform.
2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the
Feedback Fuel System enters closed loop. (Verify this by viewing the O2 sensor signal, if necessary.)
6.3 ACTUATOR TESTS 3. Shut off A/C and all other accessories. Put vehicle in park or neutral. Rev the engine slightly and watch for the
corresponding injector on-time increase on acceleration.
1) Induce propane into the intake and drive the mixture rich. If the system is working properly, the injector on-
ACTUATOR TESTS MENU time will decrease.
Injector PFI/MFI 2) Create a vacuum leak and drive the mixture lean. The injector on-time will increase.
Injector TBI 3) Raise the engine to 2500 RPM and hold it steady. The injector on-time will modulate from slightly larger to
COMPONENT TESTS
slightly smaller as the system controls the mixture. Generally, the injector on-time only has to change from
Injector PNP
ACTUATORS 0.25 ms to 0.5 ms to drive the system through its normal full rich to full lean range.
Injector Bosch
IMPORTANT: If the injector on-time is not changing, either the system may be operating in an “open loop” idle
Mixture Cntl Sol mode or the O2 sensor may be bad.
EGR Cntl Sol
IAC Motor 4. Use the Glitch Snare mode to check for sudden changes in the injector on-time.
IAC Solenoid
Trans Shift Sol
Turbo Boost Sol
Diesel Glow Plug
6-32 6-33
• Reference Waveform • Test Procedure
VEHICLE INFORMATIONS 1. Connect the CH A lead to the injector control signal from the PCM and its ground lead to the injector GND.
MAX = 35.3 V
MIN = -2.00 V YEAR : 1993 2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the
DUR = 3.92 ms MAKE : Ford Feedback Fuel System enters closed loop. (Verify this by viewing the O2 sensor signal, if necessary.)
MODEL : F150 4WD Pickup
PCM turns 3. Shut off A/C and all other accessories. Put vehicle in park or neutral. Rev the engine slightly and watch for the
circuit on here ENGINE : 5.0 L
FUELSYS : Multiport Fuel Injection corresponding injector on-time increase on acceleration.
PCM_PIN : 58 Tan wire 1) Induce propane into the intake and drive the mixture rich. If the system is working properly, the injector on-
STATUS : KOER (Key On Running) time will decrease.
RPM : Idle 2) Create a vacuum leak and drive the mixture lean. The injector on-time will increase.
PCM turns ENG_TMP : Operating Temperature 3) Raise the engine to 2500 RPM and hold it steady. The injector on-time will modulate from slightly larger to
circuit off here VACUUM : 19 In. Hg slightly smaller as the system controls the mixture. Generally, the injector on-time only has to change from
MILEAGE : 66748 0.25 ms to 0.5 ms to drive the system through its normal full rich to full lean range.
4. Use the Glitch Snare mode to check for sudden changes in the injector on-time.
When the Feedback Fuel Control System controls fuel mixture properly, the injector
on-time will modulate from about 1-6 ms at idle to about 6-35 ms under cold cranking • Reference Waveform
or Wide Open Throttle (WOT) operation.
The injector coil release spike(s) ranges are from 30 V to 100 V normally. VEHICLE INFORMATIONS
MAX = 83.5 V
MIN = 0.00 V YEAR : 1993
DUR = 5.51 ms MAKE : Chevrolet
• Troubleshooting Tips MODEL : Suburban 1500
Spikes during on-time or unusual high turn off spikes indicate the injector driver’s malfunction. ENGINE : 5.7 L
Peak and Hold Type (TBI) Injector PCM_PIN : A16 DkBlu
Straight line here (just below
battery voltage) indicates STATUS : KOER (Key On Running)
• Theory of Operation good injector driver. RPM : Snap Acceleration
Peak and Hold fuel injector drivers are used almost exclusively on Throttle Body Injection (TBI) systems. These VACUUM : 3-24 In. Hg
drivers are only used on a few selected MFI systems like GM’s 2.3 L Quad-4 engine family, Saturn 1.9 L, and Isuzu MILEAGE : 55011
1.6 L. The driver is designed to allow approximately 4 A to flow through the injector coil and then reduce the current
flow to a maximum of about 1 A. Generally, far more current is required to open the pintle valve than to hold it open. When the Feedback Fuel Control System controls fuel mixture properly, the injector
on-time will modulate from about 1-6 ms at idle to about 6-35 ms under cold cranking
The PCM continues to ground the circuit (hold it at 0 V) until it detects about 4 A flowing through the injector coil.
When the 4 A “Peak” is reached. the PCM cuts back the current to a maximum of 1 A, by switching in a current
The injector coil release spike(s) ranges are from 30 V to 100 V normally. The turn off
limiting resistor. This reduction in current causes the magnetic field to collapse partially, creating a voltage spike
spikes less than 30 V may indicate shorted injector coil.
similar to an ignition coil spike, The PCM continues the “Hold” operation for the desired injector on-time, then it shuts
Initial drive voltage should go close to 0 V. If not, injector driver may be weak.
the driver off by opening the ground circuit completely. This creates the second spike. Under acceleration the
second spike move to the right, while the first remains stationary. If the engine is running extremely rich, both spikes
are nearly on top of one another because the PCM is attempting to lean out the mixture by shortening injector on-
time as much as possible.
Spikes during on-time or unusual high turn off spikes indicate the injector driver’s malfunction. On GM and some
• Symptoms ISUZU dual TBI systems lots of extra oscillations or “hash” in between the peaks indicates a faulty injector driver in
the PCM.
Hesitation on throttle tip in, rough idle, intermittent stall at idle, poor fuel mileage, emissions test failure, low power on
acceleration.
6-34 6-35
PNP Type Injector • Reference Waveform
• Theory of Operation VEHICLE INFORMATIONS

MAX = 15.9 V PCM turns
MIN = 27.9 V injector off YEAR : 1990
A PNP type injector driver within the PCM has two positive legs and one negative leg. PNP drivers pulse power to an DUR = 6.07 ms MAKE : Jeep
already grounded injector to turn it on. Almost all other injector drivers (NPN type) are opposite. They pulse ground MODEL : Cherokee
to an injector that already has voltage applied. This is why the release spike is upside-down. Current flow is in the ENGINE : 4.0 L
opposite direction. PNP type drivers can be found on several MFI systems; Jeep 4.0 L engine families, some pre- FUELSYS : Multiport Fuel Injection
1988 Chrysler engine families, a few Asian vehicles, and some Bosch vehicles in the early 1970s like the Volvo 264 PCM turns PCM_PIN : 4 Yel wire at #4 injector
and Mercedes V-8s. injector on
by switching STATUS : KOER (Key On Running)
power on RPM : Idle
The injector on-time begins where the PCM switches power to the circuit to turn it on. The injector on-time ends
where the PCM opens the control circuit completely. ENG_TMP : Operating Temperature
VACUUM : 16.5 In. Hg
• Symptoms MILEAGE : 85716
Hesitation on throttle tip in, rough idle, intermittent stall at idle, poor fuel mileage, emissions test failure, low power on When the Feedback Fuel Control System controls fuel mixture properly, the injector
acceleration on-time will modulate from about 1-6 ms at idle to about 6-35 ms under cold cranking
• Test Procedure The injector coil release spike(s) ranges are from -30 V to -100 V normally.
2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the NOTE
Feedback Fuel System enters closed loop. (Verify this by reviewing the O2 sensor signal, if necessary.) Some injector spike heights are “chopped” to between -30 V to -60 V by clamping
diodes. There are usually identified by the flat top on their spike(s) instead of a
3. Shut off A/C and all other accessories. Put vehicle in park or neutral. Rev the engine slightly and watch for the sharper point. In those cases, a shorted injector may not reduce the spike height
corresponding injector on-time increase on acceleration. unless it is severely shorted.
1) Induce propane into the intake and drive the mixture rich. If the system is working properly, the injector on-
time will decrease.
2) Create a Vacuum leak and drive the mixture lean. The injector on-time will increase. • Troubleshooting Tips
3) Raise the engine to 2500 RPM and hold it steady. The injector on-time will modulate from slightly larger to
slightly smaller as the system control the mixture. Generally, the injector on-time only has to change from 0.25 Spikes during on-time or unusual large turn off spikes indicate the injector driver’s malfunction.
ms to 0.5 ms to drive the system through its normal full rich to full lean range.
mode or the O2 sensor may be bad.
4. Use the Glitch Snare mode to check for sudden changes in the injector on-time.
6-36 6-37
Bosch-Type Peak and Hold Injector • Reference Waveform

MAX = 50.6 V
MIN = -3.33 V YEAR : 1986
Bosch type Peak and Hold injector drivers (within the PCM) are designed to allow about 4 A to flow through the DUR = 2.23 ms MAKE : Nissan/Datsun
injector coil, then reduce the flow to a maximum of 1 A by pulsing the circuit on and off at a high frequency. The MODEL : Stanza Wagon
other type injector drivers reduce the current by using a “switch-in” resistor, but this type drivers reduce the current PCM turns ENGINE : 2.0 L
by pulsing the circuit on and off. circuit on
Current flow
PCM_PIN : B WhtBlk wire
pulsed on and Peak voltage caused STATUS : KOER (Key On Running)
off enough to by the collapse of the RPM : Idle
keep hold in injector coil. when Bos ch ty pe Peak and Hold i njector PCM turns ENG_TMP : Operating Temperature
winding activated current is reduced. drivers are found on a few European circuit off
VACUUM : 21 In. Hg
Battery voltage models with MFI s ystems and s ome MILEAGE : 183513
(or source voltage)
early to mid-1980s Asian vehicles with
supplied to the
injector MFI systems. When the Feedback Fuel Control System controls fuel mixture properly, the injector
Driver transistor
turns on, pulling
Return to battery on-time will modulate from about 1-6 ms at idle to about 6-35 ms under cold cranking
(or source) voltage or Wide Open Throttle (WOT) operation.
the injector pintle
away from its The injector coil release spike(s) ranges are from 30 V to 100 V normally.
seat, starting fuel
flow
IMPORTANT :On some European vehicles like Jaguar, there may be only one release spike because the first
release spike does not appear due to a spike suppression diode.
Injector On-Time • Troubleshooting Tips

Spikes during on-time or unusual high turn off spikes indicate the injector driver’s malfunction.
• Symptoms
Mixture Control Solenoid
Hesitation on throttle tip in, rough idle, intermittent stall at idle, poor fuel mileage, emissions test failure, low power on
acceleration
• Test Procedure The mixture control signal is the most important output signal in a carbureted Feedback Fuel Control system. On a
GM vehicle, this circuit pulses about 10 times per second, with each individual pulse (pulse width or on-time) varing,
depending upon the fuel mixture needed at that moment.
2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the In a GM vehicle, this circuit controls how long (per pulse) the main jet metering rods in the carburetor stay down
Feedback Fuel System enters closed loop. (Verify this by reviewing the O2 sensor signal, if necessary.)
(lean position). Most feedback carburetor systems operate in the same way – more mixture control on-time means
3. Shut off A/C and all other accessories. Put vehicle in park or neutral. Rev the engine slightly and watch for the lean mixture command. Generally, mixture control commands (from the PCM) that oscillate around duty cycles
corresponding injector on-time increase on acceleration. greater than 50 % mean the system is commanding a lean mixture in an effort to compensate for a long term rich
1) Induce propane into the intake and drive the mixture rich. If the system is working properly, the injector on- condition.
time will decrease.
2) Create a vacuum leak and drive the mixture lean. The injector on-time will increase. • Symptoms
3) Raise the engine to 2500 RPM and hold it steady. The injector on-time will modulate from slightly larger to Hesitation on throttle tip in, poor fuel economy, erratic idle, rich or lean emissions
slightly smaller as the system control the mixture. Generally, the injector on-time only has to change from 0.25
ms to 0.5 ms to drive the system through its normal full rich to full lean range.
• Test Procedure
mode or the O2 sensor may be bad. IMPORTANT :Before performing the test procedure, the O2 sensor must be tested and confirmed good.
4. Use the Glitch Snare mode to check for sudden changes in the injector on-time. 1. Connect the CH A lead to the mixture solenoid control signal from the PCM and its ground lead to GND.
6-38 6-39
2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the How much and when EGR flow occurs is very important to emissions and driveability. To precise control EGR flow,
Feedback Fuel System enters closed loop. (Verify this by viewing the O2 sensor signal.) the PCM sends Pulse Width Modulated signals to a vacuum solenoid valve to control vacuum flow to the EGR valve.
When applying vacuum, the EGR valve opens, allowing EGR flow. When blocking vacuum, EGR flow stops.
3. Shut off A/C and all other accessories. Put vehicle in park or neutral. Adjust lean stop, air bleed, and idle mixture
as per recommended service procedures for the carburetor being serviced. Most engine control systems do not enable EGR operation during cranking, engine warm up, deceleration, and
idling. EGR is precisely controlled during acceleration modes to optimize engine torque.
4. Use the Glitch Snare mode the check for signal dropouts.
• Symptoms
Hesitation, loose power, stall, emissions with excessive NOx, engine detonation (pinging)
FREQ = 10.0 Hz
DUTY = 48.8 % NOTE: O 2 sensor YEAR : 1984 • Test Procedure
must be good to
MAX = 31.6 V
test this circuit MAKE : Oldsmobile
1. Connect the CH A lead to the EGR control signal from the PCM and its ground lead to GND.
MODEL : Delta 88
PCM turns ENGINE : 5.0 L 2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the
circuit on FUELSYS : Feedback Carburetor Feedback Fuel System enters closed loop. (Verify this this by viewing the O2 sensor signal.)
PCM_PIN : 18 Blu wire (at test connector)
STATUS : KOER (Key On Running) 3. Shut off A/C and all other accessories. Drive the vehicle under normal driving modes; start from dead stop, light
RPM : Idle acceleration, heavy acceleration, cruise, and deceleration.
PCM turns
circuit off 4. Make sure that the amplitude, frequency, shape, and pulse width are all correct, repeatable, and present during
VACUUM : 19.5 In. Hg
EGR flow conditions.
MILEAGE : 104402
5. Make sure that all the hoses and lines to and from the intake manifold, EGR valve, and vacuum solenoid valve
When the main venturi metering circuits are adjusted properly (lean stop, air bleed, are all intact, and routed properly, with no leaks. Make sure the EGR valve diaphragm can hold the proper
etc.), the mixture control signal should oscillate around 50 % duty cycle normally. amount of vacuum. Make sure that the EGR passageways in and around the engine are clear and unrestricted
When the main metering and idle mixture adjustments are set correctly, the tall spike from internal carbon buildup.
will oscillate slightly from right to left and back again, but remain very close to the
middle of the two vertical drops in the waveform. The PCM is oscillating the signal right 6. Use the Glitch Snare mode to check for signal dropouts.
to left, based on input from the O2 sensor.
• Troubleshooting Tips VEHICLE INFORMATIONS

MAX = 29.0 V
MIN = -1.33 V YEAR : 1990
If the duty cycle does not remain around 50 %, check for vacuum leaks or a poor mixture adjustment. MAKE : Chevrolet
MODEL : Suburban
If the waveform oscillates around 50 % duty cycle during one operating mode (for instance, idle) but not another, ENGINE : 5.7 L
then check for vacuum leaks, misadjusted idle mixture, main metering mixture, or other non-feedback system
problems that affect mixture at different engine speeds.
PCM_PIN : A4 Gry wire
RPM : Light Acceleration
EGR (Exhaust Gas Recirculation) Control Solenoid PCM turns PCM pulses PCM turns ENG_TMP : Operating Temperature
circuit on circuit here circuit off VACUUM : 12-23 In. Hg
• Theory of Operation MILEAGE : 59726
EGR systems are designed to dilute the air-fuel mixture and limit NOx formation when combustion temperatures
As soon as the engine reaches the predetermined EGR requirement conditions, the
generally exceed 2500 °F (1371 °C) and air-fuel ratios are lean. The effect of mixing exhaust gas (a relatively inert
PCM should begin pulsing the EGR solenoid with a pulse width modulated signal to
gas) with the incoming air-fuel mixture is a sort of chemical buffering or cooling of the air and fuel molecules in the
open the EGR solenoid valve. EGR demands are especially high during accelerations.
combustion chamber. This prevents excessively rapid burning of the air-fuel charge, or even detonation, both of
which can raise combustion temperatures above 2500 °F. The initial formation of NOx is limited by EGR flow and
then the catalytic converter acts to chemically reduce the amounts of produced NOx entering the atmosphere.
6-40 6-41
The idle control output command from the PCM should change when accessories are
If the waveform has runted (shortened) spike heights, it indicates a shorted EGR vacuum solenoid. switched on and off or the transmission is switched in and out of gear.
The pulse width modulated signals from the PCM should control the speed of the
If the waveform has a flat line (no signal at all), it indicates a PCM failure, PCM’s EGR conditions not met, or wiring
motor, and in turn the amount of air bypassing the throttle plate.
or connector problem.
The turn off spikes may not be present in all IAC drive circuits.
Too much EGR flow can make the vehicle hesitate, loose power, or even stall. Not enough EGR flow can result in
emissions with excessive NOx and engine detonation (pinging).
IMPORTANT :Before diagnosing IAC motor, several things must be checked and verified; the throttle plate should
be free of carbon buildup and should open and close freely, the minimum air rate (minimum throttle
IAC (Idle Air Control) Motor opening) should be set according to manufacturer’s specifications, and check for vacuum leaks or
false air leaks.
Idle air control valves keep the engine idling as low as possible, without stalling, and as smoothly as possible when
accessories such as air conditioning compressors, alternators, and power steering load the engine. If the engine idle speed doesn’t change corresponding with the change of the PCM’s command signal, suspect a
bad IAC motor or clogged bypass passage.
Some IAC valves are solenoids (most Fords), some are rotating motors (European Bosch), and some are gear
reduction DC stepper motors (most GM, Chrysler). In all cases, however, the PCM varies the amplitude or pulse
width of the signal to control its operation and ultimately, idle speed.
IAC (Idle Air Control) Solenoid
Rotating IAC motors receive a continuous pulse train. The duty cycle of the signal controls the speed of the motor, • Theory of Operation
and in turn the amount of air bypassing the throttle plate.
Idle air control solenoids keep the engine idling as low as possible, without stalling, and as smoothly as possible
• Symptoms when accessories such as air conditioning compressors, alternators, and power steering load the engine.
Erratic high or low idle, stalling, high activity but no change in idle Ford’s IAC solenoids are driven by a DC signal with some AC superimposed on top. The solenoid opens the throttle
plate in proportion to the DC drive it receives from the PCM. The DC drive is applied by holding one end of the
• Test Procedure solenoid coil at battery positive while pulling the other end toward GND. The DC voltage at the driven pin decreases
as the solenoid drive current is increased.
1. Connect the CH A lead to the IAC control signal from the PCM and its ground lead to GND.
2. Run the engine at idle while turning accessories (A/C, blowers, wipers, etc.) on and off. If the vehicle has an • Symptoms
automatic transmission, put it in and out of drive and park. This will change the load on the engine and cause the Erratic high or low idle, stalling, high activity but no change in idle
PCM to change the output command signal to the IAC motor.
3. Make sure that idle speed responds to the changes in duty cycle. • Test Procedure
4. Use the Glitch Snare mode to check for signal dropouts. 1. Connect the CH A lead to the IAC control signal from the PCM and its ground lead to the chassis GND.
2. Run the engine at idle while turning accessories (A/C, blowers, wipers, etc.) on and off. If the vehicle has an
automatic transmission, put it in and out of drive and park. This will change the load on the engine and cause the
VEHICLE INFORMATIONS PCM to change the output command signal to the IAC solenoid.
DUTY = 52.5 % 3. Make sure that the amplitude, frequency, and shape are all correct, repeatable, and consistent for the various idle
MAKE : BMW
compensation modes.
MODEL : 525 I
ENGINE : 2.5 L 4. Make sure that idle speed responds to the changes in the IAC drive.
PCM_PIN : 22 WhtGrn wire
RPM : Idle
PCM turns PCM turns ENG_TMP : Operating Temperature
circuit on circuit off
VACUUM : 15 In. Hg
MILEAGE : 72822
6-42 6-43
• Reference Waveform • Symptoms
VEHICLE INFORMATIONS Slow and improper shifting, engine stops running when vehicle comes to a stop
MAX = 12.2 V • Test Procedure
MIN = 6.40 V MAKE : Ford
MODEL : Explorer 1. Connect the CH A lead to the transmission shift solenoid control signal from the PCM and its ground lead to the
ENGINE : 4.0 L chassis GND.
PCM_PIN : 21 Wht-LtBlu wire 2. Drive the vehicle as needed to make the driveability problem occur or to exercise the suspected shift solenoid circuit.
STATUS : KOER (Key On Running) 3. Make sure that the amplitude is correct for the suspected transmission operation.
RPM : Idle
ENG_TMP : Operating Temperature 4. Use the proper transmission fluid pressure gauges to make sure the transmission fluid pressure and flow being
VACUUM : 19 In. Hg controlled by the solenoid is being effected properly by solenoid operation. This will help discriminate between an
MILEAGE : 54567 electronic problem and a mechanical problem (such as a sticking solenoid valve, clogged fluid passages, or
leaking internal seals, etc.) in the transmission.
The idle control output command from the PCM should change when accessories are
switched on and off or the transmission is switched in and out of gear. • Reference Waveform
DC level should decrease as the IAC solenoid drive current is increased.
IMPORTANT :Before diagnosing IAC solenoid, several things must be checked and verified; the throttle plate Vehicle speed reached YEAR : 1993
should be free of carbon buildup and should open and close freely, the minimum air rate (minimum 35 MPH here and PCM MAKE : Ford
turned shift solenoid on
throttle opening) should be set according to manufacturer’s specifications, and check for vacuum MODEL : Explorer
leaks or false air leaks. ENGINE : 4.0 L
• Troubleshooting Tips PCM_PIN : 52 Org Yel wire
STATUS : KOBD (Key On Driven)
If the engine idle speed doesn’t change corresponding with the change of the PCM’s command signal, suspect a
RPM : 1500
bad IAC solenoid or clogged bypass passage.
VACUUM : 19 In. Hg
MILEAGE : 54567
Transmission Shift Solenoid
The drive signal should be consistent and repeatable.
The PCM controls an automatic transmission’s electronic shift solenoid or torque converter clutch (TCC) lockup
solenoid. • Troubleshooting Tips
The PCM opens and closes the solenoid valves using a DC switched signal. These solenoid valves, in effect, control If the waveform appears as a flat line (no signal at all), it can indicate a PCM failure, PCM conditions not met (shift
transmission fluid flow to clutch park, servos, torque converter lockup clutches, and other functional components of points, TCC lockup, etc.), or wiring or connector problems.
the transmission under the PCM’s control.
Some electronic shift solenoid systems use ground feed controlled solenoids that are always powered up and some
systems use power feed controlled solenoids that are always grounded. A ground feed controlled solenoid on a DC Turbo Boost Control Solenoid
switched circuit appears as a straight line at the system voltage, and drops to ground when the PCM activates the
solenoid. A power feed controlled solenoid on a DC switched circuit appears as a straight line at 0 V until the PCM • Theory of Operation
activates the solenoid.
Turbochargers increase horsepower considerably without increasing engine piston displacement. Turbochargers
Many vehicle PCM’s are programmed not to enable TCC operation until the engine reaches a certain temperature as
also improve torques over the useful RPM range and fuel economy, and reduces exhaust gas emissions.
well as a certain speed.
Turbocharger’s boost pressure must be regulated to obtain optimum acceleration, throttle response, and engine
durability. Regulating the boost pressure is accomplished by varying the amount of exhaust gas that bypasses the
exhaust side turbine. As more exhaust gas is routed around the turbine, the less boost pressure is increased.
6-44 6-45
A door (called the wastegate) is opened and closed to regulate the amount of bypass. The wastegate is controlled Diesel Glow Plug
by a vacuum servo motor, which can be controlled by a vacuum solenoid valve that receives a control signal from
the PCM. When the PCM receives a signal from the MAP sensor indicating that certain boost pressure is reached, • Theory of Operation
the PCM commands the vacuum solenoid valve to open in order to decrease boost pressure. The PCM opens the
solenoid valve via a pulse width modulated signal. Starting cold diesel engines are not easy because Blowby past the piston rings and thermal losses reduce the
amount of c ompression possible. Cold starting can be improved by a sheathed element glow plug in the
• Symptoms precombustion chamber (in case of Direct-injection (DI) engines, in the main combustian chamber).
Poor driveability, engine damage (blown head gasket), hard stall under acceleration When current flows through the heating coil of the glow plug, a portion of the fuel around the glow plug’s hot tip is
vaporized to assist in igniting the air-fuel mixture. Newer glow plug systems, which continue to operate after engine
• Test Procedure startup for up to 3 minutes, improve initial engine performance, reduce smokes, emissions, and combustian noises.
1. Connect the CH A lead to the solenoid control signal from the PCM and its ground lead to the chassis GND. Usually, a glow plug control unit supplies power to the glow plug during appropriate conditions. Some newer glow
plugs are designed with a heater element that changes resistance with temperature. The glow plug’s resistance
2. Start the engine and hold throttle at 2500 RPM for 2-3 minutes until the engine is fully warmed up and the increases as the heating element gets hotter by the combustian temperature’s increment after startup.
Feedback Fuel system enters closed loop. (Verify this by viewing the O2 sensor signal, if necessary.)
Usually, glow plug systems are power feed controlled so the waveform of the current going through its heating
3. Drive the vehicle as needed to make the suspected problem occur. element appears as a straight line at 0 V until the ignition key is switched on.
4. Make sure that the drive signal comes on as the boost pressure is regulated and the wastegate actually responds
• Symptoms
to the solenoid control signal.
No or hard start, emissions with excessive smokes, excessive combustian noises (knocks)
• Test Procedure
FREQ = 19.5 Hz YEAR : 1988 1. Set the instrument up with the current probe. (Connect the probe to the CH A.)
DUTY = 39.2 %
MAX = 28.0 V MAKE : Chrysler 2. Adjust the probe to read DC Zero.
PCM turns MODEL : LeBaron Convertible
circuit off ENGINE : 2.2 L Turbo 3. Clamp the current probe around the glow plug feed wire.
4. With the diesel engine stone cold, turn on the ignition key and watch for the readings.
PCM_PIN : 39 LtGrn Blk wire
STATUS : KOBD (Key On Driven) 5. Make sure that the amplitude of the current is correct and consistent for the glow plug systems under test.
RPM : Moderate Acceleration (35 MPH)
PCM turns ENG_TMP : Operating Temperature • Reference Waveform
circuit on
VACUUM : 5 In. Hg
MILEAGE : 77008 VEHICLE INFORMATIONS
MAX = 56 A YEAR : 1977
MIN = 1 A
As soon as the turbo engine reaches a predetermined boost pressure under MAKE : Mercedes-Benz
Ignition key
acceleration, the PCM should begin pulsing the turbo boost solenoid with a varying on MODEL : 240 D
pulse width modulated signal to open the wastegate. On deceleration, the signal is ENGINE : 2.4 L
stopped and the valve is closed. FUELSYS : Multiport Fuel Injection
Ignition key PCM_PIN : Power supply to glow plugs
off Ignition key
switched on. STATUS : KOEO (Key On Engine Off)
• Troubleshooting Tips Current begins RPM : 0
to flow through
glow plugs. ENG_TMP : Ambient Temperature
If the turn off spikes are not present, the solenoid coil may be shorted.
VACUUM : 0 In. Hg
If the drive signal never appears under the high boost conditions, the driver within the PCM may have failed. MILEAGE : 151417
If the turn off spikes are runted (shortened), the vacuum solenoid valve may be shorted.
6-46 6-47
3. Exercise the sensor, device, or circuit while watching for the amplitude of the signal. The amplitude should stay in
Look for the current going through the glow plug to be at its maximum when the
a predetermined voltage range for a given condition.
ignition key is switched on. Maximum current and operating current specifications may
be available from the manufacturer’s service manual. 4. In most cases, the amplitude of the waveform should stay at the battery voltage when the circuit is on, and go to
All glow plugs should draw about the same current under cold or hot conditions. 0 V when the circuit is off.
MAX = 20.3 V
If the waveform stays flat (at 0 V), suspect a faulty glow plug. If the waveform has drop outs, suspect an open circuit MIN = 8.00 V YEAR : 1986
in the glow plug’s heating element. An open circuit may be caused by overheat from a faulty controller, vibration, or transient spikes are normal MAKE : Oldsmobile
fatigue related malfunctions. with engine running MODEL : Toronado
ENGINE : 3.8 L
6.4 ELECTRICAL TESTS scope connected to
PCM_PIN : C16 Org and D1 BlkWht wires
PCM power and ground STATUS : KOER (Key On Running)
wiggle or shake wiring harness or RPM : Idle
ELECTRICAL TESTS MENU wires to suspect component while ENG_TMP : Operating Temperature
Power Circuit looking for drop outs in the waveform
VACUUM : 20 In. Hg
COMPONENT TESTS V Ref Circuit MILEAGE : 123686
Ground Circuit
ELECTRICAL The voltage should stay in a predetermined voltage range for a given condition (during
Alternator Output
normal operation). Transient spikes above average voltage level are normal with
Alternator Field VR
engine running.
Alternator Diode
Audio System
DC Switch Circuits • Troubleshooting Tips
If the amplitude is changing when it is not supposed to (for example, when the switch in the circuit is not being
Power Supply Circuit operated), there may be a failure in the circuit.
If the waveform has some spikes to ground, there may be an open circuit in the power side or there may be a
voltage short to ground.
This test procedure tests the integrity of the battery power supply to vehicle as well as to subsystems or switches If the waveform has some upward spikes, there may be an open circuit in the ground side.
that rely on battery power to operate. This test procedure can be used to assure components and devices are
getting the quality and quantity of power supply necessary for proper operation. This procedure can be applied to a
lot of different automotive circuits that use battery voltage as their power source, such as power supply circuits (to
Voltage Reference (V Ref) Circuit
PCM and other control modules), temperature switches, throttle switches, vacuum switches, light switches, brake
switches, cruise control switches, etc.
• Symptoms The PCM provides a stable regulated voltage, normally 5 V DC (8 V or 9 V DC on some older vehicles), to sensors
and components controlled by it for operation. The V Ref circuit should stay at their specified voltage during normal
No start, loss of power
operation. (The voltage level should not vary more than 200 mV under normal operation.)
• Test Procedure
• Symptoms
1. Connect the CH A lead to the power supply circuit of the device to be tested and its ground lead to the device’s
Low power, sensor output values out of range
GND.
2. Make sure power is switched on in the circuit so that the sensor, device or circuit is operational and current is • Test Procedure
flowing through the circuit.
1. Connect the CH A lead to the V Ref signal from the PCM and its ground lead to the sensor or chassis GND.
6-48 6-49
2. Make sure power is switched on to the PCM and monitor the voltage level of the V Ref signal from the PCM. • Test Procedure
Compare it with the manufacturer’s recommended limits.
1. Connect the CH A lead to the GND pin of the grounded device or the one side of the suspect junction and its
3. If the voltage level is unstable or the waveform shows spikes to ground, check the wiring harness for shorts or ground lead to the chassis GND or the other side of the suspect junction.
intermittent connections.
2. Make sure power is switched on in the circuit so that the sensor, device, or circuit is operational and current is
• Reference Waveform flowing through the circuit.
3. The average voltage drop across the junction should be less than 100 mV to 300 mV.
MAX = 5.33 V Sensor Reference Voltage -
MIN = 4.66 V sent out by PCM. Supplies YEAR : 1986 • Reference Waveform
voltage to various sensors. MAKE : Oldsmobile
Waveform’s amplitude should MODEL : Toronado VEHICLE INFORMATIONS
not vary more than 200 mV ENGINE : 3.8 L MAX = 40 mV
under normal operating modes MIN = -40 mV
YEAR : 1986
FUELSYS : Multiport Fuel Injection MAKE : Oldsmobile
Tests voltage drop across ground circuit
PCM_PIN : C14 Gry wire at TPS MODEL : Toronado
STATUS : KOER (Key On Running) CH A probe connected to engine block ENGINE : 3.8 L
wiggle the sensor harness/wiring COM probe connected to battery negative.
while watching the waveform’s RPM : Idle FUELSYS : Multiport Fuel Injection
Test conducted w/engine running.
amplitude to check for bad ENG_TMP : Operating Temperature
connections or chafed wires
PCM_PIN : CH A on Engine Block
VACUUM : 18 In. Hg COM on Battery Negative
MILEAGE : 123686 STATUS : KOER (Key On Running)
RPM : Idle
The voltage should stay in a predetermined voltage range for a given condition.
Normal V Ref voltage ranges are from 4.50 V to 5.50 V.
VACUUM : 18 In. Hg
MILEAGE : 123686
• Troubleshooting Tips Average voltage drop should not exceed 100 - 300 mV. If there is too much resistance
in the ground circuit, the waveform’s amplitude will be too high.
If the voltage level is unstable or the waveform shows spikes to ground, check the wiring harness for shorts or bad
connections.
Waveform’s amplitude should not vary more than 200 mV under normal operation.
If average voltage drop is excessive, clean or replace the connections and cables.
Ground Circuit
Alternator Output
A ground circuit controls the feedback on any controlled circuit by grounding that circuit to a common conductor
(ground). Alternators replaced generators due to their higher output at low engine speed, and their more compact and
lightweight design. An alternator is an AC generator with diode rectification, which converts the AC signal to a
This test procedure tests the integrity of ground circuits by performing a voltage drop test across the suspected pulsating DC signal. The DC signal charges the vehicle’s battery and supplies power to run the vehicle’s electrical
resistance in a ground circuit or the suspect junction. and electronic systems. Field current is supplied to the rotor in the alternator to vary its output. Alternator output
voltage increases as engine RPM increases.
This test procedure can be used assure components and devices are getting the quality of ground supply necessary
for proper operation. This procedure can be applied to a lot of different automotive circuits that are grounded to the The alternator’s output voltage is controlled by a solid state regulator within the PCM, in some cases. The regulator
vehicle’s electrical systems either through the engine block, chassis, or through a wire connected to the negative limits the charging voltage to a preset upper limit and varies the amount of the excitation current supplied to the field
side of the battery. winding. The field winding excitation is varied according to the battery’s need for charge and ambient temperature.
Check the manufacturer’s specs regarding the upper and lower limits of charging voltage permitted for the vehicle
• Symptoms
being checked.
Poor performance, inaccurate sensor outputs
The alternator’s output voltage should be roughly 0.8 V to 2.0 V above the static battery voltage with the KOEO (Key
6-50 6-51
Off Engine Off). Alternator Field/ VR (Voltage Reference)
• Symptoms • Theory of Operation
No start, low battery, slow cranking A voltage regulator (in the PCM) controls alternator output by adjusting the amount of current flowing through the
rotor field windings. To increase alternator output, the voltage regulator allows more current to flow through the rotor
• Test Procedure field windings. The field control current is varied according to the battery’s need for charge and ambient temperature.
Before performing the alternator output voltage test, the battery’s state of charge should be checked and a battery If the battery is discharged, the regulator may cycle the field current on 90 % of the time to increase the alternator
load test should be performed. output. If the electrical load is low, the regulator may cycle the field current off 90 % of the time to decrease the
alternator output. That is the signal is usually pulse width modulated.
1. Connect the CH A lead to the battery positive post and its ground lead to the battery negative post.
If the field control circuit is malfunctioning, the charging system can overcharge or undercharge, either creating
2. Turn off all electrical loads and start the engine.
problems.
3. Hold the engine at 2500 RPM for about 3 minutes and check the alternator’s output voltage.
• Symptoms
Undercharging, overcharging, or no charging output
AVG = 13.2 V • Test Procedure
YEAR : 1986
Test conducted with engine MAKE : Oldsmobile
running and A/C off. 1. Connect the CH A lead to the field control circuit the and its ground lead to the chassis GND.
MODEL : Toronado
ENGINE : 3.8 L 2. Start the engine and run at 2500 RPM. Operate the heater fan on high with the headlight on high beam, or use
FUELSYS : Multiport Fuel Injection battery load tester to vary the amount of load on the vehicle’s electrical system.
PCM_PIN : CH A to Positive side of Battery 3. Make sure that the voltage regulator is properly controlling the duty cycle of the alternator field drive signal as the
Normal voltage ranges
are from 0.8 volts to 2.0 COM to GND load changes.
volts above engine off STATUS : KOER (Key On Running)
(static) battery voltage.
RPM : 2500 • Reference Waveform
VACUUM : 20 In. Hg VEHICLE INFORMATIONS
MILEAGE : 123686 FREQ = 390 Hz YEAR : 1986
DUTY = 21.8 %
MAKE : Oldsmobile
Normal voltage ranges are about 0.8 V to 2.0 V above the static battery voltage with
MODEL : Toronado
the Key Off Engine Off. Over 2.0 V may indicate an overcharge condition and less than
ENGINE : 3.8 L
0.8 V may indicate an undercharge solution. Different vehicles have different charging
system specifications. Consult the manufacturer’s specs.
PCM_PIN : 3D11 at BCM Grey wire at alternator pin F
General rules of thumb; GN 14.5 to 15.4 V, Ford 14.4 to 14.8 V, and Chrysler 13.3 to
RPM : 2500
13.9 V
NOTE: A/C on high blow and headlights on VACUUM : 18 In. Hg
IMPORTANT :The test results can be different in a big way according to the ambient temperature, what electrical highbeam.
MILEAGE : 123686
loads are on the battery during testing, the age of battery, the battery’s charging state, the level and
quality of the battery’s electrolyte, or the battery design.
The charging system’s voltage regulator should vary the on-time of the alternator’s
• Troubleshooting Tips field control driv e signal depending on the electrical system requirements. The
If the output voltage is excessively high, or the battery is leaking, wet, smells like acid, or is boiling, the alternator regulator should pulse the field drive signal with the overall duty cycle average meeting
may be defective. Check the regulator for its proper operation. Also perform a voltage drop test on both sides of the the electrical system demands. When electrical load is put on the battery, the field
alternator housing and at the battery. If the voltage is different, the alternator may be grounded improperly. control circuit should go high to compensate for it. Frequency may increase during
conditions of increased charging demand.
6-52 6-53
If the voltage is high, there is no command to turn the alternator on or the regulator does not have the ability to VEHICLE INFORMATIONS
decrease the voltage. P-P = 373 mV
YEAR : 1986
If the voltage is low, the alternator will be on all the time and cause an overcharging state. MAKE : Oldsmobile
MODEL : Toronado
If the voltage can not be pulled to ground sufficiently, there may be bad regulator within the PCM. ENGINE : 3.8 L
PCM_PIN : B+ post at alternator
Alternator Diode STATUS : KOER (Key On Running)
Tested at idle with high beam and wipers
on, and A/C blower on high speed. RPM : Idle
• Theory of Operation ENG_TMP : Operating Temperature
VACUUM : 18 In. Hg
An alternator generates current and voltage by the principles of electromagnetic induction. Accessories connected to
MILEAGE : 123686
the vehicle’s charging system require a steady supply of direct current (DC) at a relatively steady voltage level. A set
of diodes, part of the alternator’s rectifier bridge, modifies the AC voltage (produced in the alternator) to the DC A bad alternator diode produces Peak to Peak voltages exceeding 2 V usually and its
voltage. When analyzing a vehicle’s charging system, both AC and DC level should be analyzed because the AC waveform will have “humps” that drop out and go much lower than the normal ones
level (called “ripple voltage”) is a clear indication of diode condition. Too high a level of AC voltage can indicate a shown above.
defective diode and discharge the battery. A shorted diode splits the pulses into pairs.
Usually, a bad alternator diode produces Peak to Peak voltages of more than 2 V.
• Symptoms
If the waveform has very noticeable dropouts with two or three times the peak to peak amplitude of a normal ripple,
Overnight battery draining, excessive AC current from alternator output, flickering lights, poor driveability the diodes are defective. Dropouts from bad diodes usually have a peak to peak voltages of around 1.5 V to 2.0 V.
If the humps in the waveform are grouped into pairs, the alternator has one or more bad diodes.
• Test Procedure
NOTE
This test is made at the rear case half of the alternator and not battery.
Audio System Speaker
The battery can act as a capacitor and absorb the AC voltage.
1. Connect the CH A lead to the B+ output terminal on the back of the alternator and its ground lead to the Automotive speakers are electromechanical devices that convert electrical signal from a vehicle’s radio (or
alternator case. monitoring system) into mechanical vibrations. The mechanical vibrations produced by automotive speakers are in
the audible frequency range from 16 to 20,000 Hz.
2. With the Key On, Engine Off, turn on the high beam headlights, put the A/C or heater blower motor on high
speed, turn on the windshield wipers, and rear defrost (if equipped) for 3 minutes. Audio signals to the speaker usually range between 0.5 and 10 V Peak to Peak. DC resistance of the speaker voice
coils is normally less then 10 ohms.
3. Start the engine and let it idle.
4. Make sure that pulses in ripple waveform are all about the same size and that pulses are not grouped into pairs. • Symptoms
A blown speaker with an open circuit
• Test Procedure
1. Connect the CH A lead to the positive speaker circuit and its ground lead to the negative speaker circuit.
2. Turn on the radio at normal listening level and make sure that the speaker drive signal is present.
3. To measure the resistance of the speaker voice coils, set the instrument to the GMM mode. Measure the
resistance with the drive signal disconnected.
6-54 6-55
• Reference Waveform 3. Exercise the switch while paying attention to the amplitude of the signal. It should stay in a predetermined voltage
range for a given condition. In most cases, the amplitude of the waveform should stay at B+ or battery voltage
VEHICLE INFORMATIONS when the circuit is on, and go to 0 V when the switch is activated.
MAX = +473 mV
MIN = -509 mV YEAR : 1989
MAKE : Buick • Reference Waveform
MODEL : Le Sabre
ENGINE : 3.8 L VEHICLE INFORMATIONS
MAX = 13.8 V
FUELSYS : Multiport Fuel Injection MIN = -1.0 V Brake pedal YEAR : 1993
PCM_PIN : CH A to speaker (+) released MAKE : Ford
here
COM to speaker (–) MODEL : Explorer
music starts new
note here STATUS : KOEO (Key On Engine Off) ENGINE : 4.0 L
RPM : 0 FUELSYS : Multiport Fuel Injection
ENG_TMP : Ambient Temperature PCM_PIN : 2 Lt Grn wire
VACUUM : 0 In. Hg STATUS : KOER (Key On Running)
MILEAGE : 93640 RPM : Idle
Brake pedal ENG_TMP : Operating Temperature
A few notes from Willie Nelson’s depressed here
VACUUM : 19 In. Hg
“On The Road Again”
MILEAGE : 54567
Automotive speaker drive signals normally range between 0.5 V and 10 V Peak to If there is a failure in the circuit, the waveform’s amplitude will change when it is not
Peak. supposed to.
Resistance of the speaker voice coils is normally less than 10 ohms.
• Troubleshooting Tips If the waveform has spikes to ground, there may be an open circuit in the power side or a voltage short to ground.
If the speaker is blown, suspect an open circuit. If the waveform has upward spikes, there may be an open in the ground side.
DC Switch Circuits 6.5 IGNITION TESTS
This test procedure can be applied to a lot of different automotive circuits that use B+ as their power source, such as
power supply circuits (to the PCM and other control modules), temperature switches, throttle switches, vacuum COMPONENT TEST
switches, light switches, brake switches, cruise control switches, etc. IGNITION TESTS MENU
IGNITION PIP/SPOUT
This test can be used to test the integrity of the battery power supply to the switches that rely on the battery power to
DI Primary
operate.
DI Secondary
• Symptoms DIS (EI) Primary
DIS (EI) Secondary
No start, lose of power, no working of switches
• Test Procedure
1. Connect the CH A lead to the power supply circuit of the switch to be tested and its ground lead to the switch
GND circuit.
2. Make sure power is switched on in the circuit so that the switch is operational.
6-56 6-57
PIP (Profile Ignition Pickup)/SPOUT (Spark Output) Reference Waveform

Ford EEC-IV PIP and SPOUT YEAR : 1993
The most common electronic ignition system found on Ford vehicles (primarily on Ford/Lincoln/Mercury) has been signals logged at 3000 RPM MAKE : Ford
dubbed TFI for Thick Film Ignition. This system uses a Hall Switch in the TFI module, mounted on the distributor, to MODEL : F150 4WD Pickup
produce a basic spark timing signal, PIP (Profile Ignition Pickup). This signal is sent to the PCM and the PCM uses ENGINE : 5.0 L
this signal to monitor results and accurately time the fuel injector and electronic spark timing output (SPO UT) FUELSYS : Multiport Fuel Injection
signals. The PCM sends the SPOUT back to the TFI module, which then fires the ignition coil primary circuit. The PCM_PIN : CH A 56 GryOrg wire
PIP signal is primarily a frequency modulated signal that increases and decreases its frequency with engine RPM, CH B 36 Pnk wire
but it has also a pulse width modulated component bec ause it is acted upon by the TFI module, based on STATUS : KOER (Key On Running)
information previously received via the SPOUT signal. “sync” “sync” RPM : 3000
pulse pulse
The SPOUT signal is a pulse width modulated signal because the PCM continually alters the SPOUT signal’s pulse ENG_TMP : Operating Temperature
width, which has the primary ignition dwell and ignition timing advance information encoded in it. The frequency of VACUUM : 21 In. Hg
the SPOUT signal also increases and decreases with engine RPM because it simply mimics the frequency of the MILEAGE : 66748
PIP signal. The edges must be sharp. Anything that affects ignition timing should change the
Many GM/European/Asian vehicles use a similar overall ignition circuit design. position of SPOUT (upper trace) with respect to PIP (lower trace). The notches out of the
top and bottom corner of PIP go away when the SPOUT connector is removed because
The rising and falling edges of the SPOUT move in relation to PIP. The rising edge controls spark timing and the this cuts off the TFI’s ability to encode the PIP signal with the SPOUT information.
falling edge controls coil saturation (dwell).
Watching both simultaneously using this instrument will tell you whether the PCM can compute timing based on Troubleshooting Tips
sensor inputs. For example, if the MAP sensor fails, the rising edge of SPOUT will not move relative to the rising
If changing manifold vacuum has no effect on the rising edges of SPOUT, check for a faulty BP/MAP sensor.
edges of PIP when Manifold Absolute Pressure changes.
If PIP is absent, the engine will not start; check for a bad TFI module or other distributor problem.
• Symptoms
If SPOUT is absent, the system may be in LOS (Limited Operation Strategy) or limp-home mode. Check for
Engine stall out, misfire, slow advance timing, hesitations, no start, poor fuel economy, low power, high emissions problems in the PCM or bad wiring harness connectors.
If the rising edges of PIP or SPOUT are rounded, timing will be inaccurate, although the system may not set an error
• Test Procedure
code. Check for problems in the module producing each signal.
1. Connect the ground leads of both channel test leads to the chassis GND’s. Connect the CH A to the PIP signal
and the CH B to the SPOUT signal. Use a wiring diagram for the vehicle being serviced to get the PCM pin
number, or color of the wire for each circuit. DI (Distributor Ignition) Primary
2. Crank or start the engine. Theory of Operation
3. With the Key On, Engine Running (KOER), let the engine idle, or use the throttle to accelerate and decelerate the The ignition coil primary signal is one of the top three most important diagnostic signals in powertrain management
engine, or drive the vehicle as needed to make the driveability problem occur. systems. This signal can be used for diagnosing the driveability problems such as no starts, stalls at idle or while
4. Look closely to see that the frequency of both signals is keeping pace with engine RPM and that the pulse width driving, misfires, hesitation, cuts out while driving, etc.
on the pulse width modulated notches of the signal changes when timing changes are required. The waveform displayed from the ignition primary circuit is very useful because occurrencies in the ignition
5. Look for abnormalities observed in the waveforms to coincide with an engine sputter or driveability problem. secondary burn are induced back into the primary through mutual induction of the primary and secondary windings.
This test can provide valuable information about the quality of combustion in each individual cylinder. The waveform
is primarily used to :
1. analyze individual cylinder’s dwell (coil charging time),
2. analyze the relationship between ignition coil and secondary circuit performance (from the firing line or ignition
voltage line),
3. locate incorrect air-fuel ratio in individual cylinder (from the burn line), and
6-58 6-59
4. locate fouled or damaged spark plugs that cause a cylinder misfire (from the burn line). Look for the burn line to be fairly clean without a lot of hash (“noise”). A lot of hash can indicate an ignition misfire in
the cylinder due to over-advanced ignition timing, bad injector, fouled spark plug, or other causes. Longer burn lines
It’s sometimes advantageous to test the ignition primary when the ignition secondary is not easily accessible.
(over 2 ms) can indicate an abnormally rich mix ture and shorter burn line (under 0.75 ms) can indicate an
abnormally lean mixture.
Symptoms
Look for at least 2, preferably more than 3 oscillations after the burn line.
No or hard starts, stalls, misfires, hesitation, poor fuel economy This indicates a good ignition coil (and a good condenser on point-type ignitions).
Test Procedure
1. Connect the CH A lead to the ignition coil primary signal (driven side) and its ground lead to the chassis GND. DI (Distributor Ignition) Secondary (Conventional Single and Parade)
2. With the Key On, Engine Running (KOER), use the throttle to accelerate and decelerate the engine or drive the Secondary ignition patterns are very useful when diagnosing ignition related malfunctions. The secondary scope
vehicle as needed to make the driveability problem or misfire occur. pattern is divided into three sections:
Firing Line (spark initiated)
3. For cranking test, set the Trigger mode to Normal.
4. Make sure that the amplitude, frequency, shape and pulse width are all consistent from cylinder to cylinder. Look Points close or
for abnormalities in the section of the waveform that corresponds to specific components. transistor turns ON
Spark Line (or Burn Line)
Points open or
Spark is extinguished
Reference Waveform transistor turns OFF
Coil oscillations
MAX = 170 V arc-over or
DUR = 2.07 ms ignition YEAR : 1987
DWELL = 12.4 ° voltage MAKE : Chrysler
OF CYL 1
MODEL : Fifth Avenue
burn ENGINE : 5.2 L
line
spark or burn FUELSYS : Feedback Carburetor Dwell Section Firing Intermediate Section
voltage PCM_PIN : CH A to Negative side of ignition coil Section
coil oscillations SECONDARY FIRING SECTION
Ignition coil begins RPM : Idle
charging here The firing section consists of a firing line and a spark (or burn) line. The firing line is a vertical line that represents the
VACUUM : 20 In. Hg voltage required to overcome the gap of the spark plug. The spark line is a semi-horizontal line that represents the
MILEAGE : 140241 voltage required to maintain current flow across the spark gap.
The Ignition Peak voltage and Burn voltage measurements are available in this test, SECONDARY INTERMEDIATE SECTION
but they should be corrected to account for the turns ratio of the coil windings. The intermediate section displays the remaining coil energy as it dissipates itself by oscillating between the primary
Look closely to see that the pulse width (dwell) changes when engine load and RPM and secondary side of the coil (with the points open or transistor off).
changes.
SECONDARY DWELL SECTION
Troubleshooting Tips The dwell section represents coil saturation, which is the period of time the points are closed or the transistor is on.
The ignition (or distributor) dwell angle is the number of degrees of distributor rotation during which the points or
Look for the drop in the waveform where the ignition coil begins charging to stay relatively consistent, which transistor are closed (or magnetic saturation time in degrees).
indicates consistent dwell and timing accuracy of individual cylinder. Normally, it takes about 10 to 15 ms for an ignition coil to develop complete magnetic saturation from primary current.
Look for a relatively consistent height on the “arc-over” voltage or firing line. A line that is too high indicates high The secondary ignition test has been an effective driveability check for over three decades along with the primary
resistance in the ignition secondary due to an open or bad spark plug wire or a large spark gap. A line that is too ignition test. The ignition secondary waveform can be useful in detection of problems in mechanical components of
short indicates lower (than normal) resistance in the ignition secondary due to fouled, cracked, or arcing spark plug engine and fuel system, as well as the ignition system components.
wire, etc.
When the PARADE mode is selected, this instrument will present a parade of all the cylinders, starting at the left with
Look for the spark or burn voltage to remain fairly consistent. This can be an indicator of air-fuel ratio in the cylinder. the spark line of the number 1 cylinder. The instrument will display the pattern for each cylinder’s ignition cycle in the
If the mixture is too lean, the burn voltage may be higher, and if too rich, the voltage may be lower than normal. engine’s firing order. For example, if the firing order for a given engine is 1,4,3,2, the instrument will display the
6-60 ignition cycles for each cylinder as shown starting with cylinder number 1, then 4, then 3, and then 2. 6-61
Firing lines should be equal. A short line 1. Connect the capacitive type ignition secondary probe to the CH A input terminal and its ground lead to chassis
indicates low resistance in the wire. A high Firing lines clearly displayed GND.
line indicates high resistance in the wire for easy comparison
2. Connect the Inductive Pickup to the COM/TRIGGER input terminals.
Available voltage
NOTE
should be about 10 kV The Inductive Pickup must be used to synchronize triggering between the spark
on a conventional ignition plug wire signal and the coil secondary signal clamped by the capacitive secondary
system and even greater probe.
with an electronic system
3. Clip the secondary probe to the coil secondary lead wire and clamp the pickup probe on the spark plug wire close
to the spark plug.
IMPORTANT :Signals from individual spark plug wires are useful only for triggering. Ignition Peak Voltage, Burn
Spark lines can be viewed side-by-side
for ease of comparison Voltage, and Burn Time measurements may not be accurate, if the signal is taken on the spark
Cylinders are displayed in firing order
plug side of the distributor, due to the rotor spark gap. For accurate measurements, use the coil
secondary signal before the distributor.
Symptoms NOTE
If you want to test SECONDARY IGNITION SINGLE, press to highlight
No or hard starts, stalls, misfires, hesitation, poor fuel economy SINGLE and SECO NDARY IGNITION PARADE, press to highlight
PARADE.
Test Procedure
4. With the Key On, Engine Running (KOER), use the throttle to accelerate and decelerate the engine or drive the
NOTE vehicle as needed to make the driveability problem or misfire occur.
A Capacitive type ignition secondary probe must be used to test the ignition
secondary circuit. 5. Make sure that the amplitude, frequency, shape and pulse width are all consistent from cylinder to cylinder. Look
Connecting the CH A or CH B leads directly to an ignition secondary circuit can for abnormalities in the section of the waveform that corresponds to specific components.
cause severe damage to the instrument or even personal injury.
Reference Waveform
Connect the test leads as displayed by the test tool’s HELP (Test Procedure) and shown in Figure below.
FIRE = 9.20 kV arc-over or
BURN = 7.42 V ignition voltage YEAR : 1984
DUR =2.39 ms MAKE : Mercedes-Benz
OF CYL 1
MODEL : 380 SE
ENGINE : 3.8 L
FUELSYS : CIS Fuel Injection
spark or burn PCM_PIN : CH A to the Coil wire
voltage
RPM : Idle
Burn line
ign. coil begins ENG_TMP : Operating Temperature
charging here VACUUM : 19.5 In. Hg
MILEAGE : 18575
Look closely to see that the pulse width (dwell) changes when engine load and RPM
changes.
6-62 6-63
Look for the drop in the waveform where the ignition coil begins charging to stay relatively consistent, which
indicates consistent dwell and timing accuracy of individual cylinder. MAX = 170 V
DUR = 1.59 ms
YEAR : 1994
Look for a relatively consistent height on the “arc-over” voltage or firing line. A line that is too high indicates high DWELL = 6.00 % arc-over or MAKE : Ford
resistance in the ignition secondary due to an open or bad spark plug wire or a large spark gap. A line that is too ignition MODEL : Explorer
voltage burn
short indicates lower (than normal) resistance in the ignition secondary due to fouled, cracked, or arcing spark plug line ENGINE : 4.0 L
spark or burn FUELSYS : Multiport Fuel Injection
wire, etc. voltage
PCM_PIN : 10 Coil A YelBlk at ignition
Look for the spark or burn voltage to remain fairly consistent. This can be an indicator of air-fuel ratio in the cylinder.
If the mixture is too lean, the burn voltage may be higher, and if too rich, the voltage may be lower than normal. ignition coil begins coil coil
charging here fires oscillations
RPM : Idle
Look for the burn line to be fairly clean without a lot of hash. A lot of hash can indicate an ignition misfire in the ENG_TMP : Operating Temperature
cylinder due to over-advanced ignition timing, bad injector, fouled spark plug or other causes. Longer burn lines VACUUM : 19.5 In. Hg
(over 2 ms) can indicate an abnormally rich mixture and shorter burn lines (under 0.75 ms) can indicate an MILEAGE : 40045
abnormally lean mixture.
The Ignition Peak voltage and Burn voltage measurements are available in this test,
Look for at least 2, preferably more than 3 oscillations after the burn line. This indicate a good ignition coil (a good but they should be corrected to account for the turns ratio of the coil windings.
condenser on point-type ignitions).
DIS (Distributorless Ignition System) Primary
• Theory of Operation indicates consistent dwell and timing accuracy of individual cylinder.
The DIS (or EI) primary ignition test is an effective test for locating ignition problems that relate to EI ignition coils. Look for a relatively consistent height on the “arc-over” voltage or firing line. A line that is too high indicates high
The waveform is very useful because occurrences in the ignition secondary burn are induced back into the primary resistance in the ignition secondary due to an open or bad spark plug wire or a large spark gap. A line that is too
through mutual induction of the primary and secondary windings. The waveform is primarily used to : short indicates lower (than normal) resistance in the ignition secondary due to fouled, cracked, or arcing spark plug
wire, etc.
1. analyze individual cylinder dwell (coil charging time),
2. analyze ignition coil and secondary circuit performance (from the firing line), Look for the spark or burn voltage to remain fairly consistent. This can be an indicator of air-fuel ratio in the cylinder.
If the mixture is too lean, the burn voltage may be higher, and if too rich, the voltage may be lower than normal.
3. locate incorrect air-fuel ratio in individual cylinders (from the burn line), and
Look for the burn line to be fairly clean without a lot of hash, which can indicate an ignition misfire in the cylinder due
4. locate fouled or damaged spark plugs that cause a cylinder misfire (from the burn line). to over-advanced ignition timing, bad injector, fouled spark plug or other causes. Longer burn lines (over 2 ms) can
This test can be useful in detection of problems in mechanical engine and fuel system components, as well as indicate an abnormally rich mixture and shorter burn lines (under 0.75 ms) can indicate an abnormally lean mixture.
ignition system components. Look for at least 2, preferably more than 3 oscillations after the burn line. This indicate a good ignition coil (a good
• Symptoms
No or hard starts, stalls, misfires, hesitation, poor fuel economy
DIS (Distributorless Ignition System) Secondary
• Test Procedure
1. Connect the CH A lead to the ignition coil primary signal (driven side) and its ground lead to the chassis GND.
Most Distributorless Ignition systems use a waste spark method of spark distribution. Each cylinder is paired with the
2. With the key on, engine running, let the engine idle, or use the throttle to accelerate and decelerate the engine or
cylinder opposite to it (1-4, or 3-6, or 2-5). The spark occurs simultaneously in the cylinder coming up on the
drive the vehicle as needed to make the driveability problem or misfire occur.
compression stroke and in the cylinder coming up on the exhaust stroke. The cylinder on the exhaust stroke requires
3. Make sure that the amplitude, frequency, shape and pulse width are all consistent from cylinder to cylinder. Look very little of the available energy to fire the spark plug.
for the abnormalities in the section of the waveform that corresponds to specific components.
The remaining energy is used as required by the cylinder on the compression stroke. The same process is repeated
4. If necessary, adjust the trigger level for a stable display. when the cylinders reverse roles.
6-64 6-65
The secondary POWER/WASTE spark display waveform can be used to test several aspects of EI (or DIS) system 1. Connect the capacitive type ignition secondary probe to the CH A input terminal and its ground lead to chassis
operation. This test can be used to : GND.
1. analyze individual cylinder dwell (coil charging time), 2. Clip the secondary probe to the coil secondary lead wire before the distributor.
2. analyze ignition coil and secondary circuit performance (from the firing line), 3. With the Key On, Engine Running (KOER), use the throttle to accelerate and decelerate the engine or drive the
vehicle as needed to make the driveability problem or misfire occur.
3. locate incorrect air-fuel ratio in individual cylinders (from the burn line), and
4. If the firing line is negative, press to invert the pattern.
4. locate fouled or damaged spark plugs that cause a cylinder misfire (from the burn line).
5. Make sure that the amplitude, frequency, shape and pulse width are all consistent from cylinder to cylinder. Look
Generally on modern high energy ignition (HEI) systems, firing voltages should be around 15 kV to beyond 30 kV. for abnormalities in the section of the waveform that corresponds to specific components.
Firing voltages vary based on spark plug gap, engine compression ratio, and air-fuel mixture. On dual spark EI
systems, the WASTE spark is usually much lower in peak voltage than the POWER spark. Close to 5 kV can be • Reference Waveform
normal.
• Symptoms FIRE = 8.53 kV YEAR : 1994
BURN = 1.30 kV
No or hard starts, stalls, misfires, hesitation, poor fuel economy DUR = 1.36 ms arc-over MAKE : Ford
RPM = 780 or ignition MODEL : Explorer
voltage
• Test Procedure ENGINE : 4.0 L
spark or burn FUELSYS : Multiport Fuel Injection
voltage PCM_PIN : Cyl #1 Spark Plug wire
NOTE
A Capacitive type ignition secondary probe must be used to test the ignition Ignition coil begins STATUS : KOER (Key On Running)
secondary circuit. Connecting the CH A or CH B leads directly to an ignition charging here RPM : Idle
Burn
secondary circuit can cause severe damage to the instrument or even personal line ENG_TMP : Operating Temperature
injury. VACUUM : 19.5 In. Hg
MILEAGE : 40045
Connect the test leads as displayed by the test tool’s HELP (Test Procedure) and shown in Figure below.
Look closely to see that the pulse width (dwell) changes when engine load and RPM
changes.
indicates consistent dwell and timing accuracy of individual cylinder.
Look for a relatively consistent height on the “arc-over” voltage or firing line. A line that is too high indicates high
resistance in the ignition secondary due to an open or bad spark plug wire or a large spark gap. A line that is too
short indicates lower (than normal) resistance in the ignition secondary due to fouled, cracked, or arcing spark plug
wire, etc.
Look for the spark or burn voltage to remain fairly consistent. This can be an indicator of air-fuel ratio in the cylinder.
If the mixture is too lean, the burn voltage may be higher, and if too rich, the voltage may be lower than normal.
Look for the burn line to be fairly clean without a lot of hash, which can indicate an ignition misfire in the cylinder due
to over-advanced ignition timing, bad injector, fouled spark plug or other causes. Longer burn lines (over 2 ms) can
indicate an abnormally rich mixture and shorter burn lines (under 0.75 ms) can indicate an abnormally lear mixture.
Look for at least 2, preferably more than 3 oscillations after the burn line. This indicate a good ignition coil (a good
6-66 6-67
6.6 DIESEL TESTS Some tips to keep in mind :
• Always position the piezo pickup on the fuel line at about the same distance from the injector.
• Place the pickup on a straight part of the fuel line. Don’t place it on a bent part of the line.
• Always compare results with a reference waveform from a good diesel engine to get acquainted with the signal
VEHICLE DATA shape.
• Always compare signals at the same engine speed (RPM).
IGNITION • Pump timing is critical and should occur within 1 degree of crankshaft rotation.
DIESEL
The diesel test functions are selected if “IGNITION: DIESEL” has been set in the VEHICLE DATA menu. To choose Diesel Injector
a preset DIESEL test menu, select COMPONENT TESTS from the MAIN MENU. From the resulting menu, select (Diesel RPM Measurement and Diesel Injection Pattern Display)
DIESEL TESTS menu.
Use the optional Diesel Probe Set consisting of a Piezo Pickup, which is clamped on the diesel fuel pipe, and a
Diesel Adaptor to be connected to the CH A input of the instrument.
COMPONENT TESTS
DIESEL TEST MENU RPM = 903 DUR = Duration of the injection pulse
DIESEL
DIESEL INJECTOR DUR = 0.6 ms
ADVANCE
Introduction
During the compression stroke of a diesel engine, the intake air is compressed to about 735 psi (50 Bar). The
temperature hereby increases up to 1,292 ° to 1,652 °F (700 ° to 900 °C). This temperature is sufficient to cause
automatic ignition of the Diesel fuel which is injected into the cylinder, shortly before the end of the compression
stroke and very near to the TDC (Top Dead Center).
Diesel fuel is delivered to the individual cylinders at a pressure of between 5145 psi and 17,640 psi (350 Bar and
1200 Bar). The start of the injection cycle should be timed within 1 ° Crankshaft to achieve the optimum trade-off
between engine fuel consumption and combustion noise (knock). A timing device controls the start of the injection
• Analysis of Injection Pattern at Idle Speed
and will also compensate for the propagation times in the fuel delivery lines.
Diesel RPM measurements are necessary for adjusting idle speed, checking maximum RPM, and performing smoke
The delivery valve opens When the injector opening
tests at fixed RPM values. and a pressure wave pressure is reached to more than
proceeds toward the 1,470 psi (100 Bar), the needle
Measurement Conditions injector. valve overcomes its needle spring
force and lifts.
Cleaning : The fuel lines (to be measured on) should be cleaned in order to assure a good contact of the fuel line
itself to the Piezo Pickup and ground clip. Use sandpaper (preferably a de-greaser) to clean the lines. The injection process ends, the
delivery valve closes and the
Positioning and Pr obe Connection : The Piezo Adapter should be placed as close as possible to the Diesel pressure in the fuel line drops.
injector on a straight part of the fuel line. Clamp the ground clip close to the Piezo Pickup. Make sure that the ground The injection pumps plunger
This quick drop causes the
clip does not make contact to the piezo itself or to adjacent fuel lines. Connect the adapter to the instrument. Notice nozzle to close instantly,
moves in the supply direction
preventing the nozzle from
that the ground wire is shorter than the signal wire in order to have the weight of probe and cable loaded on the and thus generating a high
opening again, and preventing
ground wire, not on the signal wire. The piezo element may not bounce or rattle on the fuel line, or make contact to pressure in the pressure
backflow of combustion gases.
gallery.
other fuel lines or any other material close by.
6-68 6-69
Diesel Advance 7. Maintenance
Diesel pump testers are used to calibrate pumps exactly to the engine’s requirements. The testers monitor the
signals from the reference on the engine’s flywheel. The start of the delivery is monitored and timing adjustments WARNING
can be made at different speeds.
Avoid Electrical Shock or Fire:
We can reveal problems in the timing of the start of fuel delivery compared to the TDC signal of the flywheel sensor
through this advance measurement, which cannot be an absolute and accurate diesel pump adjustment test. • Use only insulated probes, test lead, and connectors specified in this manual when making measurements > 42 V
Peak (30 Vrms) above earth ground or on circuits > 4800 VA.
• Test Procedure • Use probes and test leads within ratings and inspect them before use. Remove probes and test leads before
1. Clamp the piezo pickup and its ground clip on the fuel line of the first cylinder close to the injector and connect opening case or battery cover.
the adapter to the CH A. • The instrument must be disconnected from all voltage sources before it is opened for any adjus tment,
replacement, maintenance, or repair.
2. Connect the CH B to the TDC sensor signal output or HI. Don’t use the ground lead of the CH B test lead, since
the instrument is already grounded through the pickup adapter to the fuel line (double grounding). • Capacitors inside may still be charged even if the instrument has been disconnected from all voltage sources.
Discharge all high voltage capacitors before making resistance, continuity, or diodes measurements.
3. Use the cursors to read the advance in degrees of the flywheel rotation.
Cleaning
Clean the instrument with a damp cloth and a mild detergent.
Do not use abrasives, solvents, or alcohol.
RPM = 898 RPM = 1689 Do not use any type of paper to clean the display screen. This will cause scratches and diminish the transparency of
ADV = 15 ° ADV = 12.9 °
the screen. Use only a soft cloth with a mild detergent.
Keeping Batteries in Optimal Condition

Always operate the instrument on batteries until a battery symbol appears in the top right of the display. This
indicates that the battery level is too low and the batteries need to be recharged.
CAUTION
Frequent charging of the batteries when they are not completely empty can cause a “memory effect”. This means
that the capacity of the Ni-MH batteries decreases, which can reduce the operating time of the instrument.
(Advance at idle) (Advance at 1689 RPM) Replacing and Disposing of Batteries
WARNING
To avoid electrical shock, remove the test leads, probes, and battery charger before replacing the batteries.
1. Disconnect the test leads, probes, and battery charger from both the source and the instrument.
2. Remove the battery cover by using a screwdriver.
3. Replace the Ni-MH battery pack with a new Ni-MH battery pack ONLY specified in this manual.
4. Reinstall the battery cover by using a screwdriver.
NOTE
Do not dispose of the replaced battery with other solid waste. Used batteries
should be disposed of by a qualified recycler or hazardous materials handler.
Fuses Not Required

Since the instrument uses electronically protected inputs, no fuses are required.
6-70 7-1
8. Specifications
General Specifications
Operation temperature : 32 °F to 104 °F (0 °C to 40 °C)

Storage temperature : -4 °F to 140 °F (-20 °C to 60 °C)
Relative Humidity : 0 % to 80 % at 32 °F to 95 °F (0 °C to 35 °C),

0 % to 70 % at 32 °F to 131 °F (0 °C to 55 °C)
Temperature Coefficient : Nominal 0.1 x (Specified Accuracy) / °C (< 18 °C or > 28 °C ; < 64 °F or > 82 °F)
Max Voltage between
any input and Ground : 300 V
Max Input Voltage : 300 V
GMM Basic DC Accuracy : 0.3 %

Bandwidth : DC to 5 MHz (-3dB)
Max Sample rate : 25 Mega sample/second
Graphing Multimeter
Display Counter : 5,000 count
Display : 280 x 240 pixels (active area) with backlit (EL)

Reference Waveform : 51 Waveform
PC interface : USB version 1.1
Power requirements : Rechargeable Battery

(External AC to DC Power Adaptor)
Battery Life : 4 Hours with backlit off

Size (H x W x D) : 9.06 x 4.72 x 1.97” (230 x 120 x 50 mm)
Safety & design : CAT II 300 V per IEC 1010-1, UL 3111-1 and C22.2 No. 1010-1
Accessory
User Manual : 1 ea
AC to DC Power Adaptor
/Battery Charger : 1 ea
Shielded Test Leads : 2 ea (red and yellow)
Ground Leads
for Shielded Test Leads : 2 ea (black)
Alligator Clips : 3 ea (red, yellow and black)
8-1
Back Probe Pins : 3 ea (red, yellow and black) Trigger
2 mm Adaptor : 3 ea (red, yellow and black) Trigger Source : CH A, CH B, TRIGGER (External trigger)
Secondary Pick-up : 1 ea Sensitivity (CH A) : < 1.0 div to 5 MHz
Ground Lead Sensitivity (Trigger) : 0.2 V p-p
for Capacitive Secondary Probe : 1 ea (black)
Modes : Single shot, Normal, Auto
Inductive Pick-up : 1 ea
Coupling : AC, DC
OBD II Code Reader Cable : 1 ea
Slope : Rising and falling edge
Soft Carrying Case : 1 ea
USB Interface Others
Cable and Software (Optional) : 1 ea
Glitch Snare : SCOPE Mode (Component test only)
Current Probe - CA113 OS/AT (Optional) : 1 ea
Acquire Mode : SCOPE Mode
Diesel Probe Set (Optional) : 1 ea
Setup memory : 8 Waveform & Setup
Temperature Probe (Optional) : 1 ea
Reference waveform : 51 Waveform and Setup
Isolated 12V Charging Adaptor (Optional) : 1 ea
Cursor : Time and Volt
Isolated 24V Charging Adaptor (Optional) : 1 ea
Instrument Setup : Language, Contrast, Graticule
Scope Specifications
Graphing Multimeter (GMM) Specifications
Horizontal
Sample rate : 25 Mega sample/second DC Voltage Measurement
Record length : 1000 Points Range Resolution Accuracy

500 mV 0.1 mV
Update rate : Real time, Roll
5V 0.001 V
Accuracy : ± (0.1 % + 1 pixel)
50 V 0.01 V ± (0.3 % + 5 d)
Sweep rate : 1 µs to 50 sec in a 1, 2, 5 sequence (Scope mode) 600 V 0.1 V
5 s to 24 Hours in a 1, 2, 5 sequence (GMM mode)
> Input Impedance : 10 M
Vertical
AC Voltage Measurement
Band width : DC to 5 MHz ; -3 dB
Accuracy
Resolution : 8 bit Range Resolution
40 Hz ~ 400 Hz 400 Hz ~ 10 kHz
Channel : 2 Channel
500 mV 0.1 mV
Coupling : AC, DC, GND 5V 0.001 V
Input Impedance : 1 Mohm / 70 pF 50 V 0.01 V ± (0.5 % + 5 d) ± (2.5 % + 5 d)
Maximum Input Voltage : 300 V 600 V 0.1 V
Volt/Division : 50 mV to 100 V in a 1, 2, 5 sequence > Input Impedance : 10 M
Accuracy : ±3%
8-2 8-3
(AC+DC) Voltage Measurement Continuity Test
Accuracy Test Voltage Threshold Response time
Range Resolution
40 Hz ~ 400 Hz 400 Hz ~ 10 kHz 1.2 V Approx. 70 W 1 ms
DC 500 mV 0.1 mV
DC 5 V 0.001 V Diode Test
± (0.8 % + 5 d) ± (3.0 % + 5 d)
DC 50 V 0.01 V Range Open Circuit Voltage Accuracy
DC 600 V 0.1 V 2.0 V 3.0 V ± (2.0 %5 d)
Temperature Measurement
RPM Measurement
Range Resolution Accuracy
Mode Range Accuracy -50 °C to 1300 °C 0.1 °C ± 3 °C
4 cylinder 120 - 20000 RPM -58 °F to 2372 °F 0.1 °F ± 5.4 °F
2 RPM
2 cylinder 60 - 10000 RPM
DC Ampere Measurement (Current Probe Output)

Frequency Measurement
Function Range Resolution Accuracy 30 mA ~ 20 A 1 mV/10 mA ± (1.5 % + 20 mA)
Frequency 10 Hz 0.001 Hz 100 mA ~ 40 A 1 mV/100 mA ± (2.0 % + 20 mA)
100 Hz 0.01 Hz 40 A ~ 60 A 1 mV/100 mA ± (4.0 % + 0.3 A)
1 kHz 0.1 Hz
10 kHz 1 Hz ± (0.1 % + 3 d) AC Ampere Measurement (Current Probe Output)
100 kHz 10 Hz
Accuracy
1 MHz 100 Hz Range Resolution
40 Hz ~ 1 kHz 1 kHz ~ 5 kHz
5 MHz 1 kHz
30 mA ~ 10 A 1 mV/10 mA ± (2.0 % + 20 mA) ± (4.0 % + 30 mA)
% Duty 2.0 % ~ 98 % 0.1 % Pulse Width > 2 µs
100 mA ~ 40 A 1 mV/100 mA ± (2.0 % + 20 mA) ± (6.0 % + 30 mA)
Dwell 3.6 ° ~ 356.4 ° 0.1 ° 1.2 °/krpm + 2 d
40 A ~ 60 A 1 mV/100 mA ± (8.0 % + 0.3 A)
Pulse Width 2 µs ~ 450 ms (Pulse Width > 2 µs)
Ohm Measurement
500 0.1
5k 0.001 k ± (0.5 % + 5 d)
50 k 0.01 k
500 k 0.1 k
5M 0.001 M ± (0.75 % + 5 d)
30 M 0.01 M ± (0.75 % + 10 d)
8-4 8-5
GLOSSARY
Terminology Description
ABS Antilock Brake System

AC Alternating Current
AC Coupling A mode of signal transmission that passes the dynamic (AC) signal component to the
input (INPUT A or INPUT B), but blocks the DC component. Useful to observe an AC
signal that is normally riding on a DC signal, e.g. charging ripple.
Acquisition The process of gathering measurement data into the instrument’s memory.
Acquisition Rate The number of acquisitions performed per second
Actuator A mechanism for moving or controlling something indirectly instead of by hand.
Alternating Current An electrical signal in which current and voltage vary in a repeating pattern over time.
Alternator An AC generator with diode rectification.
Amplitude The difference between the highest and the lowest level of a waveform.
Attenuation The decrease in amplitude of a signal
Auto Range Activates an automatic adaptation of the instrument to the input signal in amplitude,
timebase, and triggering.
Bandwidth A frequency range.
Baud Rate Communication parameter that indicates the data transfer rate in bits per second.
Blower A device designed to supply a current of air at a moderate pressure. The blower case is
usually designed as part of a ventilation system.
BNC Coaxial type input connector used for INPUT A and INPUT B.
Bottom Display The lower part of the display, where the function key menu is listed.
Bypass Providing a secondary path to relieve pressure in the primary passage.
Carburetor A mechanism which automatically mixes fuel with air in the proper proportions to
provide a desired power output from a spark ignition internal combustion engine.
Catalytic Converter An in-line exhaust system device used to reduce the level of engine exhaust emissions.
Closed Loop (Engine) An operating condition or mode which enables modification of programmed instructions
based on a feedback system.
Continuity Instrument setup to check wiring, circuits, connectors, or switches for breaks (open
circuit) or closed circuits.
Contrast This setting (expressed in a percentage) determines the contrast ratio between display
text or graphics and the LCD background. (0 % is all white. 100 % is all black.)
Conventional Ignition system that uses a distributor.
Ignition System
G-1
Terminology Description Terminology Description
Cursor A vertical or horizontal line (kind of ruler) that you can place on the screen and move Function Key Labels Labels shown on the bottom display that indicate the function of the function keys
horizontally or vertically to measure values at certain points of the waveform. to .
DC Direct Current Function Key Menu The function key labels listed on the bottom display.
DC Coupling A mode of signal transmission that passes both AC and DC signal components to the Glitch A momentary spike in a waveform. This can be caused by a momentary disruption in
input (INPUT A or INPUT B) of the instrument. the circuit under test.
Default Setup The setup that exists as long as there are no changes made to the settings. Glow plug A combustion chamber heat generating device to aid starting diesel engines.
Diesel Probe A test probe that has a pickup element to measure the pressure pulse in the diesel fuel Governor A device designed to automatically limit engine speed.
pipe. It converts fuel pipe expansion into voltage.
Ground An electrical conductor used as a common return for an electric circuit(s) and with a
Differential Measurement of the difference between the waveform sample values at the positions of relative zero potential.
Measurement(Delta) the two cursors.
Ground Controlled A circuit that is energized by applying ground; voltage has been already supplied.
Diode An electrical device that allows current to flow in one direction only. Circuit
Direct Current A signal with constant voltage and current Hall-Effect Sensor A semiconductor moving relative to a magnetic field, generating a variable voltage
(or Hall Sensor) output. Used to determine position in the automotive industry.
DIS Distributorless Ignition System
Idle Rotational speed of an engine with vehicle at rest and accelerator pedal not depressed.
Division A specific segment of a waveform, as defined by the grid on the display.
Drive A device which provides a fixed increase or decrease ratio of relative rotation between Ignition System used to provide high voltage spark for internal combustion engines.
its input and output shafts. Inductance The signal caused by a sudden change of a magnetic field.
Driver A switched electronic device that controls output state. For example, when you turn off the current through a solenoid, a voltage spike is
generated across the solenoid.
Duty Cycle On-time or off-time to period time ratio expressed in a percentage.
Intake Air Air drawn through a cleaner and distributed to each cylinder for use in combustion.
Earth Ground A conductor that will dissipate large electrical currents into the Earth.
Intermittent Irregular, a condition that happens with no apparant or predictable pattern.
ECM Electronic Control Module on a vehicle.
Invert To change to the opposite polarity. Puts the waveform display upside down.
ECU Electronic Control Unit on a vehicle.
Knock (Engine) The sharp, metallic sound produced when two pressure fronts collide in the combustion
EIA-232-D/RS-232C International standard for serial data communication to which the optical interface of the chamber of an engine.
instrument conforms.
Lamda Sensor Oxygen (or O2) sensor.
Electromagnetic Mutual disturbance of signals, mostly caused by signals from adjacent wiring.
LCD Liquid Crystal Display
Interference
EMI Electromagnetic Interference Link General term used to indicate the existence of communication facilities between two points.
(Electrical/Electronic)
Feed Controlled Circuit A circuit that is energized by applying voltage; it has already been grounded.
Manifold A device designed to collect or distribute fluid, air or the like.
Filter Electrical circuits or device that only passes or blocks certain signal frequencies. An
Master Reset Resets the instrument to the factory “Default Setup”.
application can be to remove noises from a signal.
You can do this by turning power on while pressing the F5 function key ( ).
Freeze Frame A block of memory containing the vehicle operating conditions for a specific time.
Menu A list of choices for selecting a test, a function, or a setting.
Frequency The number of times a waveform repeats per second, measure in Hz. 1 Hz equals one
cycle per second. Malfunction Indicator A required on-board indicator to alert the driver of an emission related malfunction.
Lamp (MIL)
Fuel Trim A set of positive and negative values that represent adding or subtracting fuel from
engine. A fuel correction term. Noise Extraneous electrical signal that can interfere with other electrical signals. The noise can
disturb the function of the signal when it exceeds a certain electrical level.
G-2 G-3
Terminology Description Terminology Description
NTC A resistor that has a Negative Temperature Coeffic ient; resistance decreases as Scan Tool A device that interfaces with and communicates information on a data link.
temperature increases.
Sample A reading taken from an electrical signal. A waveform is created from a successive
O2 Sensor Oxygen sensor number of samples.
Off-time The part of an electrical signal during which an electrical device is de-energized. Sampling Rate The number of readings taken from an electrical signal every second.
On-time The part of an electrical signal during which an electrical device is energized. Saturated Driver Fuel injection circuit that maintains the same voltage level throughout its on-time.
OBD II On-Board Diagnostics Second Generation (or Generation Two) Secondary Pickup An accessory that can be clamped on the high voltage coil wire used to measure
secondary ignition patterns.
OBD II Systems Provide comprehensive diagnostics and monitoring of emission controlling systems.
Shielded Test Lead A test lead that is surrounded by a conductive screen to protect the measurement signal
Open Loop An operating condition or mode based on programmed instructions and not modified by
against environmental influences, such as electrical noise or radiation.
a feedback system.
Shift Solenoid A device that controls shifting in an automatic transmission.
Peak Value The highest or lowest value of a waveform.
Single Shot A signal measured by an oscilloscope that only occurs once (also called a transient
Peak-and-Hold A method for regulating the current flow through electronic fuel injectors. Supplies
event).
higher current necessary to energize the injector, then drops to a lower level just
enough to keep the injector energized. Spark Advance The relationship between the ignition timing and top dead center (DTC).
Pixel The smallest graphic detail possible for the liquid crystal display (LCD) Spike A (high) voltage pulse during a short period of time (sharp pulse).
Powertrain The elements of a vehicle by which motive power is generated and transmitted to the Throttle A valve for regulating the supply of a fluid, usually air or a fuel/air mixture, to an engine.
driven axles.
Time Base The time defined per horizontal division on the display.
Pressure (Absolute) The Pressure referenced to a perfect vacuum.
Trace The displayed waveform that shows the variations of the input signal as a function of
Pressure (Differential) The pressure difference between two regions, such as between the intake manifold and time.
the atmospheric pressures.
Trigger Determines the beginning point of a waveform.
PTC A res istor that has a Positive Temperature Coefficient; resistance increas es as
Trigger Level The voltage level that a waveform must reach to start display.
temperature increases.
Trigger Slope The voltage direction that a waveform must have to start display. A positive Slope
Pulse A voltage signal that increases or decreases from a constant value, then returns to the
requires the voltage to be increasing as it crosses the Trigger Level, a negative Slope
original value.
requires the voltage to be decreasing.
Pulse Modulated A circuit that maintains average voltage levels by pulsing the voltage on and off.
Trigger Source The instrument input that supplies the signal to provide the trigger.
Rail A manifold for fuel injection fuel.
Transducer A device that receives energy from one system and retransmits (transfers) it, often in a
Range Specified limits in which measurements are done. different form, to another system.
For example, the cruise control transducer converts a vehicle speed s ignal to a
Reference Voltage An unaltered voltage applied to a circuit. Battery plus (B+) and ground (GND) are
modulated vacuum output to control a servo.
examples of reference voltages.
Turbocharger A centrifugal device driven by exhaust gases that pressurize the intake air, thereby
Regulator (Voltage) A device that automatically controls the functional output of another device by adjusting
increasing the density of charge air and the consequent power output from a given
the voltage to meet a specified value.
engine displacement.
Relay A generally electromechanical device in which connections in one circuit are opened or
USB Universal Serial Bus (visit www.usb.org for details.)
closed by changes in another circuit.
User’s Last Display The last display having been displayed just before the instrument was turned off.
Root Mean Square Conversion of AC voltages to the effective DC value.
(RMS) Vertical Scale The scale used for vertical display (vertical sensitivity) expressed in certain units per
division.
RPM Engine speed expressed in Rotations Per Minute of the crankshaft.
G-4 G-5
Terminology Description Menu Overview
Voltage Drop Voltage lose across a wire, connector, or any other conductor.
Voltage drop equals resistance in ohms times current in amperes (ohm’s Law). COMPONENT TESTS MENU SENSOR TESTS MENU
Wastegate A valve used to limit charge air pressure by allowing exhaust gases to bypass the ACTUATORS O 2S Sensor (Zirc)
turbocharger. MAIN MENU
IGNITION ECT Sensor
Waveform The pattern defined by an electrical signal. COMPONENT TESTS
SCOPE
IAT Sensor
WOT Wide Open Throttle. GRAPHING MULTIMETER
CKP Magnetic
INSTRUMENT SETUP
CKP Hall
CKP Optical
GRAPHING MULTIMETER MENU VEHICLE DATA MENU CMP Magnetic
VOLT DC, AC CYLINDERS : 4 CMP Hall
OHM/DIODE/CONTINUITY CYCLES :4 CMP Optical
RPM BATTERY : 12 V VSS Magnetic
FREQUENCY IGNITION : CONV VSS Optical
DUTY CYCLE MAP Analog
PULSE WIDTH MAP Digital
DWELL MAF Analog
IGNITION PEAK VOLTS MAF Digi Slow
IGNITION BURN VOLTS MAF Digi Fast
IGNITION BURN TIME MAF Karman-Vrtx
INJECTOR ON TIME CONV (default)
AMP DC, AC DIS
Injector TBI
Injector PNP
Injector Bosch
Mixture Cntl Sol
EGR Cntl Sol
INSTRUMENT SETUP MENU IAC Motor
DISPLAY OPTIONS DISPLAY OPTIONS MENU IAC Solenoid
FILTER MENU
FILTER USER LAST SETUP : OFF Trans Shift Sol
INPUT A : OFF
AUTO POWER OFF CONTRAST : 4
INPUT B : OFF Turbo Boost Sol
LANGUAGE GRATICULE : ON Diesel Glow Plug
VERSION INFORMATION HORIZ TRIG POS : 10 %
ELECTRICAL TESTS MENU
Power Circuit
V Ref Circuit
Ground Circuit
Alternator Output
LANGUAGE MENU AUTO POWER OFF MENU Alternator Field VR
LANGUAGE : ENGLISH AUTO POWER OFF : ON Alternator Diode
AUTO POWER OFF TIME : 30 min Audio System
DC Switch Circuits
IGNITION TESTS MENU

PIP/ SPOUT
DI Primary
G-6

Osciloscopio 1006

Uploaded by

Copyright:

Available Formats

Osciloscopio 1006

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Osciloscopio 1006

Uploaded by

Copyright:

Available Formats

Model 1006

a world leader in test & measurement

FINE INSTRUMENTS CORPORATION

341-5, SONGNAE-DONG, SOSA-GU, BUCHON-SHI, KYUNGGI-DO KOREA

© Copyright 2004 Fine Instruments Corp. All right reserved.

COMPONENT TESTS MENU SENSOR TESTS MENU

IGNITION TESTS MENU

• Haynes Publications Using Your Instrument Safely

Follow the general safety guidelines below;

3.1 PRIMARY SIGNAL TYPES FOUND IN MODERN VEHICLES

Pulse Width Modulated Signals

3.4 SIGNAL PROBING WITH AN OSCILLOSCOPE

4.1 PRODUCT DESCRIPTION

This instrument offers the following features:

Performing a Navigation Exercise

Figure 2. Selecting IGNITION Menu

Power Sources and Charging the Battery

Figure 4. Key Control Overview 4.4 MEASUREMENT CONNECTIONS

ITEM KEYS DESCRIPTION

COM (as single input)

IGNITION TESTS MENU

Figure 6. Automotive Test Functions & Setups Overview

For example, IGNITION DI SECONDARY

DI Primary DI Primary Function keys

This mode is very suitable to find faults in slowly changing

5.2 SCOPE DISPLAYS

Using Single and Dual Input Scope Mode

INPUT A Control Functions

Indicates signal source channel B.

Making an Easy Setup SCOPE INPUT B

settings to create a stable display. (Autoranging is default)

SCOPE If you select , trigger occurs at a rising(positive) edge of the signal.

SCOPE Noise Filter Function

Press to select AUTO or Press to select the trigger source.

Time difference between TIME CURSOR 1 5.3 GMM DISPLAYS

DC VOLT DC Average Continuous MAIN MENU GRAPHING MULTIMETER MENU

Press to measure AC Press to reset maximum

Press to invert the displayed ignition

5.4 DUAL INPUT SCOPE OPERATION

Dual Input Scope

Using Single and Dual Input Scope

Press to select between readings in %,

Changing Instrument Setup

Normal Peak Detect

• Sample points displayed

AUTO POWER OFF MENU

VERSION INFORMATION MENU

Using the Internal Battery Power

Using OBD II Code Reader Mode Diagnostic Trouble Codes (DTCs)

• PCM(Powertrain Control Module) • Warm-up Cycle

Retrieving I/M Readiness Monitor Status

VEHICLE INFORMATION Emissions test failure, poor fuel economy.

• Reference Waveform • Symptoms [OBD II DTC’s: P0120 ~ P0124, P0220 ~ P0229]

• Theory of Operation • Troubleshooting Tips

Optical Camshaft Position (CMP) Sensor

• Reference Waveform • Symptoms [OBD II DTC’s: P0105 ~ P0109]

Digital Manifold Absolute Pressure (MAP) Sensor • Troubleshooting Tips

• Reference Waveform • Test Procedure

• Symptoms [OBD II DTC’s: P0100 ~ P0104]

VEHICLE INFORMATIONS • Theory of Operation