AT600 Manual

Flow
AquaTrans™ AT600
User’s Manual
bhge.com 910-312 Rev. D

September 2017
AquaTrans™ AT600
Panametrics Ultrasonic Flow Meter for Liquids
User’s Manual
910-312 Rev. D
September 2017
bhge.com
© 2017 Baker Hughes, a GE company – All rights reserved.
Baker Hughes reserves the right to make changes in specifications and features shown herein, or discontinue the product
described at any time without notice or obligation. Contact your BHGE representative for the most current information. The
Baker Hughes logo is a trade mark of Baker Hughes, a GE company. The GE Monogram is a trademark of the General Electric
Company.
[no content intended for this page]
Contents
Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Terms and Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Safety Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Auxiliary Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Chapter 1. General Installation Instructions
1.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Unpacking the AT600 system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Installing the Electronics Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6 Calculating the Transducer Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.7 Choosing a Clamp-On Fixture/Transducer Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.8 Mounting the Clamp-on Fixture and Transducer System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 2. Clamp-On Fixture and Transducer Installation
2.1 Installing an AT600 Clamp-On Fixture and Transducer System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.1 Transducer Spacing = 32 to 250 mm or 50 to 320 mm, Traverses = 2, Fixtures = 1 . . . . . . . . . . . . . . . . . 11
2.1.2 Transducer Spacing = 320 to 940 mm, Traverses = 2, Fixtures = 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.1.3 Transducer Spacing = 0 to 250 mm or 0 to 320 mm, Traverses = 1, Fixtures = 2 . . . . . . . . . . . . . . . . . . . . 17
2.1.4 Transducer Spacing >320 mm, Traverses = 1, Fixtures = 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.2 Installing a CF-ES Clamp-On Fixture and Transducer System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3 Installing a General Clamping Fixture and Transducer System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.1 Installing C-RS or C-PT Transducers with an RG316 Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.2 Installing C-RS or C-PT Transducers with an RG62 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 3. Wiring the AT600 Electronics
3.1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2 Wiring the Line Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.3 Wiring the Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4 Wiring the System Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.5 Wiring the Analog Output for HART Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.6 Wiring the Modbus Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.7 Wiring the Frequency/Totalizer/Alarm Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.8 Wiring the Gate Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chapter 4. Initial Setup and Programming
4.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.2 AT600 Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.3 Display Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AquaTrans™ AT600 User’s Manual iii

Contents
4.3.1 Changing the Display for One- or Two-Variable Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4.3.2 Changing the Measurement Type for One- or Two-Variable Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.3.3 Changing the Measurement Type or Units for the Totalizer Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.3.4 Starting or Stopping the Totalizer Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.3.5 Resetting the Totalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.4 Entering the Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.4.1 Display Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.4.2 Keypad Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.4.3 Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.4.4 Program and Program Review Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.5 User Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.5.1 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.5.2 Units Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.5.3 Density. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.5.4 Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.5.5 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.6 Inputs/Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.6.1 Programming the Analog Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.6.2 Programming the Digital Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.6.3 Programming the Modbus/Service Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.6.4 Programming Digital Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.7 Sensor Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4.7.1 Meter Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4.7.2 Mounting Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.7.3 Programming the Pipe Menu when Wetted selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.7.4 Programming the Pipe Menu when Clamp-on selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.7.5 Programming the Transducer when Clamp-on selected. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.7.6 Programming the Transducer when Wetted selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
4.7.7 Programming the Number of Traverses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
4.7.8 Programming the Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
4.7.9 Programming the Fluid Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
4.7.10 Calculating the Path when Clamp-on selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
4.7.11 Enter the Path when Wetted selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Chapter 5. Error Codes and Troubleshooting
5.1 Error Display in the User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.1.1 Error Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.1.2 Flow Error String. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.2 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.2.2 Flowcell Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
iv AquaTrans™ AT600 User’s Manual

Contents
Chapter 6. Communication
6.1 MODBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
6.1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
6.1.2 MODBUS Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
6.2 HART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
6.2.1 Device Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
6.2.2 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
6.3 Additional Device Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
6.4 Device Variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
6.5 HART Engineering Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168
Appendix A. Specifications
A.1 Overall Operation and Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
A.2 Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174
A.3 Clamp-On Ultrasonic Flow Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
A.4 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
A.4.1 Wiring Cable Specifications and Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
A.4.2 Cable Fixing Requirement and Gland Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
A.4.3 Display Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
A.4.4 Product Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
Appendix B. Data Records
B.1 Service Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
B.2 Data Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
B.3 Initial Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
B.4 Diagnostic Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
Appendix C. Updating the Firmware in the Field
C.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
C.1.1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
C.1.2 Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
C.2 Performing the Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
C.2.1 Check the Current Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
C.2.2 Update Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
C.3 Clearing an S2 Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186
C.4 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186
Appendix D. Menu Maps
D.1 The Display Measurement Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
D.2 The Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
D.3 The Main Menu > User Preferences Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189
D.4 The Main Menu > Inputs/Outputs Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
D.5 The Main Menu > Sensor Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191
AquaTrans™ AT600 User’s Manual v

Contents
D.6 The Main Menu > Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192

D.7 The Main Menu > Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193
D.8 The Main Menu > Factory Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
vi AquaTrans™ AT600 User’s Manual

Preface
Product Registration
Thank you for purchasing your AquaTrans™ AT600 from Baker Hughes, a GE Company. Please register your
product at www.gemeasurement.com/productregistration for product support such as the latest
software/firmware upgrades, product information and special promotions.
Services
BHGE provides customers with an experienced staff of customer support personnel ready to respond to
technical inquiries, as well as other remote and on-site support needs. To complement our broad portfolio of
industry-leading solutions, we offer several types of flexible and scalable support services including:
Training, Product Repairs, Extended Warranties, Service Agreements and more. Please visit
www.gemeasurement.com/services for more details.
Terms and Conditions

Sales Terms and Conditions for your recent purchase of a BHGE product, including the applicable product
Warranty, can be found on our website at the following link:
www.gemeasurement.com/sales-terms-and-conditions
Typographical Conventions
Note: These paragraphs provide information that provides a deeper understanding of the situation, but is not
essential to the proper completion of the instructions.
IMPORTANT: These paragraphs provide information that emphasizes instructions that are essential to proper
setup of the equipment. Failure to follow these instructions carefully may cause unreliable
performance.
CAUTION! This symbol indicates a risk of potential minor personal injury and/or severe damage to
the equipment, unless these instructions are followed carefully.
WARNING! This symbol indicates a risk of potential serious personal injury, unless these
instructions are followed carefully.
Safety Issues
WARNING! It is the responsibility of the user to make sure all local, county, state and national
codes, regulations, rules and laws related to safety and safe operating conditions are met for each
installation.
Attention European Customers! To meet CE Marking requirements for all units intended for use in
the EU, all electrical cables must be installed as described in this manual.
AquaTrans™ AT600 User’s Manual vii

Preface
Auxiliary Equipment
Local Safety Standards
The user must make sure that he operates all auxiliary equipment in accordance with local codes, standards,
regulations, or laws applicable to safety.
Working Area
WARNING! Auxiliary equipment may have both manual and automatic modes of operation. As
equipment can move suddenly and without warning, do not enter the work cell of this equipment
during automatic operation, and do not enter the work envelope of this equipment during manual
operation. If you do, serious injury can result.
WARNING! Make sure that power to the auxiliary equipment is turned OFF and locked out before
you perform maintenance procedures on this equipment.
Qualification of Personnel
Make sure that all personnel have manufacturer-approved training applicable to the auxiliary equipment.
Personal Safety Equipment

Make sure that operators and maintenance personnel have all safety equipment applicable to the auxiliary
equipment. Examples include safety glasses, protective headgear, safety shoes, etc.
Unauthorized Operation
Make sure that unauthorized personnel cannot gain access to the operation of the equipment.
viii AquaTrans™ AT600 User’s Manual

Preface
Environmental Compliance
RoHS
The AquaTrans™ AT600 fully complies with RoHS regulations (Directive 2011/65/EU).
Waste Electrical and Electronic Equipment (WEEE) Directive

BHGE is an active participant in Europe’s Waste Electrical and Electronic Equipment (WEEE) take-back
initiative (Directive 2012/19/EU).
The equipment that you bought has required the extraction and use of natural resources for its production. It
may contain hazardous substances that could impact health and the environment.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on
the natural resources, we encourage you to use the appropriate take-back systems. Those systems will reuse
or recycle most of the materials of your end life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems, please contact your local or
regional waste administration.
Please visit http://www.gemeasurement.com/environmental-health-safety-ehs for take-back instructions and

more information about this initiative.
AquaTrans™ AT600 User’s Manual ix

Preface
x AquaTrans™ AT600 User’s Manual


1.1 Introduction
Thank you for purchasing the AT600 ultrasonic flow meter. The AT600 is a clamp-on ultrasonic flow meter
for the measurement of liquid products. It is designed for the industrial applications, including water,
wastewater, steel, campus energy, and others. The AT600 utilizes a new electronics platform and industrial
design to make it extremely simple to install and use in the field.
• So easy to use, it practically installs itself
The AT600 consists of the new AT600 electronics, a metal enclosure, the field proven AT transducer system,
and a clamp-on transducer fixture (see Figure 1 below).
U-Bolt
Electronics
Power Cable
Transducer Cable
Fixture
Strap With Transducer Installed
Figure 1: Typical AT600 System Mounted on a Pipe
AquaTrans™ AT600 User’s Manual 1

1.2 Theory of Operation

The AT600 flow meter uses a procedure called Transit-Time Flow Measurement. In this method, two
transducers, which are in acoustic communication with each other, serve as both ultrasonic signal
generators and receivers. That is, the second transducer can receive ultrasonic signals transmitted by the
first transducer and vice versa.
In operation, each transducer functions as a transmitter, generating a certain number of acoustic pulses, and
then as a receiver for an identical number of pulses (see Figure 2 and Figure 3 below). The time interval
between transmission and reception of the ultrasonic signals is measured in both directions. When the
liquid in the pipe is not flowing, the transit-time downstream equals the transit-time upstream. However,
when the liquid is flowing, the transit-time downstream is less than the transit-time upstream. The
difference between the downstream and upstream transit times is proportional to the velocity of the flowing
liquid and its sign indicates the direction of flow.
Figure 2: Flow and Transducer Paths (Two Traverses)
Figure 3: Flow and Transducer Paths (One Traverse)
2 AquaTrans™ AT600 User’s Manual

1.3 Safety Guidelines

To ensure safe and reliable operation of the AT600, the system must be installed in accordance with the
guidelines discussed in this manual. This chapter includes the following topics:
• “Unpacking the AT600 system” on page 4
• “Installing the Electronics Enclosure” on page 5
• “Choosing a Clamp-On Fixture/Transducer Location” on page 7
• “Mounting the Clamp-on Fixture and Transducer System” on page 8
WARNING! The AT 600 flow transmitter can measure the flow rate of many fluids, some of which
are potentially hazardous. The importance of proper safety practices cannot be overemphasized.
WARNING! Be sure to follow all applicable local safety codes and regulations for installing electrical
equipment and working with hazardous fluids or flow conditions. Consult company safety personnel
or local safety authorities to verify the safety of any procedure or practice.
ATTENTION EUROPEAN CUSTOMERS! To meet CE Marking and UL Marking requirements, all cables
must be installed as described in “Wiring Cable Specifications and Requirements” on page 177.

1.4 Unpacking the AT600 system

Before removing the AT600 system from the crate, please inspect the flow meter. Before discarding any of
the packing materials, account for all components and documentation listed on the packing slip. The
discarding of an important item along with the packing materials is all too common. If anything is missing
or damaged, contact BHGE Customer Care immediately for assistance.
Please note that the AT600 system (see Figure 4 below) is available in a variety of configurations to meet your
needs, so the packing list will vary for each system. As an example, a typical packing list is:
1. One AT600 electronics enclosure
2. Two clamp-on fixtures
3. Two transducers (installed in one of the two clamp-on fixtures)
4. One transducer cable (installed on fixture with transducers)
5. Two clamp-on fixture mounting straps for each fixture
6. Two “U” bolts for pipe mounting of the AT600 electronics enclosure
7. One USB flash drive with user’s manual and calibration sheet
8. One inner hexagon spanner
9. Three M16 cable glands (installed on the AT600 electronics enclosure)
10. Two pieces of Solid Couplant
11. Quick installation guide
12. Calibration Sheet
13. Cabling tools
Figure 4: Typical AT600 Shipping Container

1.5 Installing the Electronics Enclosure

The AT600 electronics is housed in a powder-coated, aluminum, NEMA type 4X/IP67 enclosure suitable for
indoor or outdoor use. See Figure 5 below for the mounting dimensions and weight of the AT600 electronics
enclosure.
72.50
128
120
160
M16 GLAND x3
M20 GLAND x2 63.50 3
202 13
226
Wall Mount
72.50
2 Inch Pipe
202
Weight is about 1.5 kg

for the whole meter Assembly
Pipe Mount
Figure 5: Mounting the AT600 Electronics Enclosure

1.5 Installing the Electronics Enclosure (cont.)

The installation base of AT600 electronics enclosure can be rotated 90° to keep a horizontal view of the user
interface in any mounting orientation. See Figure 6 below for drawings of the AT600 mounting base.
Horizontal
Vertical
Figure 6: The AT600 Mounting Base
1.6 Calculating the Transducer Spacing

Before installing the clamp-on fixture(s) and transducers, you must program the AT600 to calculate the
required transducer spacing for your planned installation. To accomplish this task, go to “Sensor Setup” on
page 66 and follow the instructions in that section. After obtaining the required transducer spacing value,
return here and continue to the next section.

1.7 Choosing a Clamp-On Fixture/Transducer Location

For a given fluid and pipe, the accuracy of AT600 depends on the location and alignment of the transducers.
In addition to accessibility, when choosing a transducer location, follow these guidelines:
• Position the clamp-on fixture(s) and transducer system so that there are at least 10 pipe diameters of
straight, undisturbed flow upstream and 5 pipe diameters of straight, undisturbed flow downstream
from the measurement point (see Figure 7 below). Undisturbed flow means avoiding sources of
turbulence in the fluid such as valves, flanges, expansion joints, elbows, swirl, and cavitation.
Flow Direction
UPSTREAM DOWNSTREAM
10 X D (in.) 5 X D (min)
Figure 7: AT600 Clamp-On Fixture/Transducer Location
• Locate the transducers on a common axial plane along the pipe (see Figure 8 below). The transducers
should be mounted on the side of the pipe, rather than the top or bottom, because the top of the pipe
tends to accumulate gases and the bottom tends to accumulate sediment. Either condition may cause
excessive attenuation of the ultrasonic signal. There is no similar restriction with vertical pipes, as
long as the flow direction is upward to prevent free falling of the fluid in a partially filled pipe.
Good Flow
Flow
Flow
Good
Bad Bad
Good
Figure 8: Good and Bad Transducer Locations

1.8 Mounting the Clamp-on Fixture and Transducer System

The AT600 transducer system includes one or two clamp-on fixtures, two transducers and one transducer
cable. One clamp-on fixture is shipped with both transducers installed and the transducer cable connected
to the transducers. This fixture is the default setup for most applications. If a second fixture has been
ordered, it is shipped empty.
Transducers available for use with the AT600 flow meter are listed in Table 1 below.
Table 1: Available Transducers

Model Frequency Fixture Pipe Sizes
AT6 2, 1, 0.5 MHz AT600 2 in. (50 mm)
CF-LP1 4 MHz CF-ES 0.5-2 in. (15-50 mm)
UTXDR1 4 MHz SPCF 0.5-8 in. (15-200 mm)
C-RS2 1, 0.5 MHz GCF 2 in. (50 mm)
C-PT2 2, 1, 0.5 MHz GCF 2 in. (50 mm)

1
Go directly to: “Installing a CF-ES Clamp-On Fixture and Transducer System” on page 20.
2Go directly to: “Installing a General Clamping Fixture and Transducer System” on page 20.
The AT600 clamp-on fixture and AT6 transducer system can be installed on pipe sizes 2 in. (50 mm). For
optimum performance in any specific application, either a two-traverse or one-traverse installation can be
chosen. Because the maximum pipe size for a single clamp-on fixture is 250 mm for 2 MHz transducers or
320 mm for 1 MHz and 0.5 MHz transducers, the detailed installation requirements differ based on the
calculated transducer spacing and the chosen number of traverses. Refer to Table 2 below to find the
parameters for your specific configuration.
Table 2: AT600 Clamp-On Fixture Installation

Pipe Size Range Transducer Number of Transducer Spacing Number of
mm inches Frequency (MHz) Traverses (mm) Fixtures
50 to 100 2 to 4 2 4 32 to 250 1
100 to 150 4 to 6 2 2 32 to 250 1
50 to 150 2 to 6 2 1 0 to 250 2
100 to 300 4 to 12 1 2 50 to 320 1
300 to 600 12 to 24 1 2 320 to 940 2
600 to 1500 24 to 60 1 1 >320 2
200 to 300 8 to 12 0.5 2 50 to 320 1
300 to 900 12 to 36 0.5 2 320 to 940 2
>900 >36 0.5 1 >320 2
IMPORTANT: See “Sensor Setup” on page 66 to calculate the required transducer spacing. A two traverse
installation is recommended for most applications.
IMPORTANT: If there is any type of coating or protective layer on the outer pipe surface, it must be removed at
the locations where the transducers and couplant contact the pipe surface.

1.8 Mounting the Clamp-on Fixture and Transducer System (cont.)

From the information on the previous page and the documentation included with your AT600 flow meter
system, you should already know the following details about your installation:
• Pipe Size
• Transducer Model
• Transducer Frequency
• Number of Traverses
• Calculated Transducer Spacing
• Number of Clamp-On Fixtures
Based on the known information, proceed directly to one of the following sections in the next chapter for
instructions on installing your AT600 clamp-on fixture(s) and transducers on the pipe:
Note: See the flowchart in Figure 9 on page 10 to assist in choosing the appropriate instructions for your
specific configuration.
• “Transducer Spacing = 32 to 250 mm or 50 to 320 mm, Traverses = 2, Fixtures = 1” on page 11
• “Transducer Spacing = 320 to 940 mm, Traverses = 2, Fixtures = 2” on page 14
• “Transducer Spacing = 0 to 250 mm or 0 to 320 mm, Traverses = 1, Fixtures = 2” on page 17
• “Transducer Spacing >320 mm, Traverses = 1, Fixtures = 2” on page 19

1.8 Mounting the Clamp-on Fixture and Transducer System (cont.)
START HERE
Note: The red boxes are the recommended configuration, which works for most applications.
AT6 Trans. UTXDR Trans. CF-LP Trans. C-RS Trans. C-PT Trans.
AT600 Fixture CF-ES Fixture GCF Fixture
2 MHz 1 MHz 0.5 MHz 4 MHz 4 MHz

[Section 2.2 on page 19] [Section 2.3 on page 19]
2 Traverses 1 Traverse
1 Fixture 2 Fixtures 2 Fixtures

[Section 2.1.1 on page 11] [Section 2.1.2 on page 14]
Spacing to 320 Spacing >320

[Section 2.1.3 on page 16] [Section 2.1.4 on page 18]
Figure 9: Flowchart to Transducer Installation Instructions


2.1 Installing an AT600 Clamp-On Fixture and Transducer System
The instructions in this section are for installations using the AT600 clamp-on fixture only. For installations
using other clamp-on fixtures, see “Installing a CF-ES Clamp-On Fixture and Transducer System” on page 20
or “Installing a General Clamping Fixture and Transducer System” on page 20.
2.1.1 Transducer Spacing = 32 to 250 mm or 50 to 320 mm, Traverses = 2, Fixtures = 1

Note: A two traverse installation with one clamp-on fixture is the standard AT600 configuration.
When the required transducer spacing is 32 to 250 mm for a 2 MHz transducer or 50 to 320 mm for a 1 MHz
or
0.5 MHz transducer, one clamp-on fixture is needed for a dual traverse installation. Proceed as follows:
1. Install the AT600 clamp-on fixture with transducers on the pipe using two mounting straps.
a. Choose a location with enough straight pipe run (refer to Figure 7 on page 7).
b. Install the two mounting straps on the pipe about 12 in. (30 cm) apart (see Figure 10 below).
Figure 10: Mounting Straps Installed on Pipe
c. Hold the fixture against the pipe and move the mounting straps onto the fixture. Then, tighten
the screws on the straps, and verify that the straps remain in place on the fixture (see Figure 11
below).
Move
Align
Screw Tighten

Figure 11: 2 Traverse Installation with 1 Clamp-On Fixture
2.1.1 Transducer Spacing = 32 to 250 mm or 50 to 320 mm, Traverses = 2, Fixtures = 1 (cont.)

IMPORTANT: If there is any type of coating or protective layer on the outer pipe surface, it must be removed at
the locations where the transducers and the couplant contact the pipe surface.
2. Connect the power and transducer cables to the AT600, as shown in Figure 23 on page 23.
3. If you haven’t already done so, power the meter On and program your site data to determine the
required transducer spacing (see “Sensor Setup” on page 66).
4. Set the two transducers at the spacing calculated by the meter and tighten them in place, as follows:
a. Loosen both transducers and rotate the fixture so that the transducers are in view (see Figure 12
below).
Hand Wheel Transducers
Figure 12: Transducers Rotated into View
b. Set the transducers to the spacing calculated by the meter. If you are using solid couplant, apply it
to both transducer faces. Then, rotate the transducers back onto the rail (see Figure 13 below).
ing
Spac
Couplant
Figure 13: Set Transducer Spacing and Apply Couplant


5. See Figure 14 below for an example of a completed installation. In this drawing, LSL is the Lower
Specified Limit and USL is the Upper Specified Limit for the installation.
Note: For a one-fixture installation, LSL is 0 on the scale and USL is 250 mm for a 2 MHz transducer or 320 mm
for a 1 MHz or 0.5 MHz transducer. The transducer spacing is measured from LSL to a point USL.
LSL USL
UPSTREAM DOWNSTREAM
Spacing
Figure 14: Installation for 2 Traverses with 1 Fixture
6. Your clamp-on fixture and transducer installation is now complete. To wire your AT600 flow meter,
proceed to “Wiring the AT600 Electronics” on page 23.

2.1.2 Transducer Spacing = 320 to 940 mm, Traverses = 2, Fixtures = 2

For a two traverse installation with a calculated transducer spacing of 320 to 940 mm for a 1 MHz or 0.5 MHz
transducer, two fixtures are installed on the same side of the pipe. To do so, complete the following steps:
1. Install the four mounting straps on the pipe with a spacing of 12 in. (30 cm) between each pair of
straps.
2. Hold one of the clamp-on fixtures, with two transducers and one cable, against the pipe between the
upstream pair of straps and move the two mounting straps onto the fixture (see Figure 15 below).
Then, tighten the screws on the mounting straps, and verify that the straps remain in place on the
fixture.
Bar
Figure 15: 2 Traverse Installation with 2 Clamp-On Fixtures

3. Repeat step 2 to install the second clamping fixture, with no transducers or cable, on the pipe
between the downstream pair of straps. Use the bar on the second fixture to connect the two fixtures.
Then, move the straps onto the second fixture and tighten the screws.
IMPORTANT: Be sure the bar on the left side of the second fixture is in close contact with the bar on the first
fixture.
4. Set the spacing between the two transducers in the upstream clamping fixture to the value
calculated by the meter and tighten them back onto the pipe, as follows:
a. Rotate the fixture so that the transducers are in view (see Figure 12 on page 12).
b. Remove the downstream transducer from the first fixture (see Figure 16 below), disconnect the
transducer cable, and route the cable into the second fixture. Then, install the downstream
transducer into the second fixture and reconnect the transducer cable. If you are using solid
couplant, apply it to both transducer faces. Then, rotate the transducers back onto the rail

DOWNSTREAM
UPSTREAM
Figure 16: Moving the Downstream Transducer
2.1.2 Transducer Spacing = 320 to 940 mm, Traverses = 2, Fixtures = 2 (cont.)

IMPORTANT: Tight contact must be made between the bars on the two fixtures to ensure an accurate spacing.
5. See Figure 17 and Figure 18 below for examples of a completed installation in the following
situations:
Note: In this drawing, LSL is the Lower Specified Limit and USL is the Upper Specified Limit for each fixture.
a. For a calculated transducer spacing of 320 to 620 mm for a 1 MHz or 0.5 MHz transducer, locate
the upstream transducer at the USL1 position on the first fixture. Then, locate the downstream
transducer at the calculated transducer spacing position (USL2) on the second fixture.
LSL1 USL1 LSL2 USL2

0 300 620
UPSTREAM DOWNSTREAM
Spacing
Figure 17: Transducer Spacing of 320 to 620 mm with 2 Fixtures
b. For a calculated transducer spacing of 620 to 940 mm for a 1 MHz or 0.5 MHz transducer, locate
the upstream transducer at the LSL1 position on the first fixture. Then, locate the downstream
transducer at the calculated transducer spacing position (between LSL2 and USL2) on the second
fixture.

LSL1 USL1 LSL2 USL2

0 320 620 940
250
UPSTREAM DOWNSTREAM
Spacing
Figure 18: Transducer Spacing of 620 to 940 mm with 2 Fixtures

2.1.3 Transducer Spacing = 0 to 250 mm or 0 to 320 mm, Traverses = 1, Fixtures = 2

For a one traverse installation with a calculated transducer spacing of 0 to 250 mm for a 2 MHz transducer or
0 to 320 mm for a 1 MHz or 0.5 MHz transducer, two clamp-on fixtures are installed on opposite sides of the
pipe. To install this configuration, complete the following steps:
1. Mark a straight line parallel to the pipe centerline on the top of the pipe (i.e., the 12 o’clock position).
2. Use a band tape to measure the circumference of the pipe. Then, mark two additional lines on the
pipe parallel to the first line. Locate these lines 1/4 of the way around the pipe in each direction from
the original line (i.e., at the 3 o-clock and 9 o’clock positions).
3. Install two mounting straps on the pipe about 12 in. (30 cm) apart (see Figure 19 below).
4. Hold one clamp-on fixture, with two transducers and one cable, on the pipe along one of the lines
marked in step 2. Then, move the two straps onto the ends of this fixture.
5. Hold the remaining (empty) clamp-on fixture on the opposite side of the pipe from the first fixture.
Then, move the two straps onto the ends of this clamp-on fixture.
6. Align the two fixtures to be equal distances from the band tape. Tighten both straps securely.
Band Tape
+1/4
nce
circumfere
-1/4
nce
circumfere
Figure 19: 1 Traverse Installation with 2 Fixtures


7. Set the spacing between the two transducers to the value calculated by the meter as follows:
a. Loosen the fixture rails and rotate the rails so the transducers are in view.
b. Remove the upstream transducer from the first fixture (see Figure 20 below). Disconnect the
transducer cable and route the cable into the second fixture.
Note: The cable for the upstream transducer needs to be pulled out through one side of the rail on the first
fixture and inserted through the side of the rail on the second fixture.
c. Install the upstream transducer into the second fixture, and reconnect the transducer cable.
d. Locate the upstream transducer at the zero position of the second fixture, and then move the
downstream transducer to the required position on the first fixture. If you are using solid
DOWNSTREAM
UPSTREAM
Figure 20: Relocate the Upstream Transducer

2.1.4 Transducer Spacing >320 mm, Traverses = 1, Fixtures = 2

For a one traverse installation with a calculated transducer spacing of >320 mm for a 1 MHz or 0.5 MHz
transducer, two clamp-on fixtures are installed on opposite sides of the pipe. To install this configuration,
refer to Figure 21 below and complete the following steps:
1. Mark a straight line parallel to the pipe centerline on the top of the pipe (i.e., the 12 o’clock position).
2. Use a band tape to measure the circumference of the pipe. Then, mark two additional lines on the
pipe parallel to the first line. Locate these lines 1/4 of the way around the pipe in each direction from
the original line (i.e., at the 3 o-clock and 9 o’clock positions).
3. Install the four mounting straps on the pipe with a spacing of about 12 in. (30 cm) between each pair
of straps. Then, mark a fixture position on each of the straight lines, using the band tape as a
reference point.
4. Hold one clamp-on fixture, with two transducers and one cable, on the pipe between the pair of
downstream straps and along one of the lines marked in step 2. Then, move the two downstream
straps onto the ends of this clamp-on fixture. Tighten the strap screws and verify that the straps
remain on the ends of the fixture.
5. Hold the remaining (empty) clamp-on fixture along the line on the opposite side of the pipe from the
first fixture and between the upstream pair of straps. Then, move the two upstream straps onto the
ends of this clamp-on fixture. Tighten the strap screws and verify that the straps remain on the ends
of the fixture.
6. Set the spacing between the two transducers to the value calculated by the meter as follows:
a. Loosen the fixture rails and rotate the rails so the transducers are in view.
b. Remove the upstream transducer from the first fixture (see Figure 21 below). Disconnect the
transducer cable and route the cable into the second fixture.
c. Install the upstream transducer in the second fixture, and reconnect the transducer cable.
d. Locate the upstream transducer at the zero position of the second fixture, and then move the
downstream transducer to the required position on the first fixture. If you are using solid
UPSTREAM
+1/4
nce
circumfere
-1/4
nce
circumfere
AM
DOWNSTRE
Figure 21: 1 Traverse Installation for Transducer Spacing >320 mm

2.2 Installing a CF-ES Clamp-On Fixture and Transducer System

To use the AT600 flow meter on 0.5 to 2 in. (15 to 50 mm) pipes, the CF-ES clamp-on fixture must be used.
UTXDR or CF-LP transducers are available for installation in this fixture. Note the following specifications:
• UTXDR Transducer: Use cable adapter p/n 704-1678-LF with the AT6 transducer cable,
-40 to +120°C (-40 to +248°F) Temperatures, 4 MHz Frequency
• CF-LP Transducer: Use cable adapter p/n 210-410-LF with the AT6 transducer cable,
up to 230°C (446°F) Temperatures, 4 MHz Frequency.
Detailed installation instructions for this fixture and transducer are available in BHGE document #916-082.
2.3 Installing a General Clamping Fixture and Transducer System

Both the C-RS and C-PT transducers are mounted on the pipe with the BHGE General Clamping Fixture (GCF).
For detailed installation instructions refer to following:
• C-RS Transducer Installation Guide (BHGE document #916-077)
• C-PT Transducer Installation Guide (BHGE document #916-074)
2.3.1 Installing C-RS or C-PT Transducers with an RG316 Cable

The standard AT6 transducer cable is an RG316 cable with an SMA connector on the transducer end. To
connect the BNC connector on the C-RS or C-PT transducer to the SMA connector on the AT6 transducer
cable, a BNC to SMA Adapter is needed. See Figure 22 below and install the cable adapter on the transducer
end of your AT6 cable.
AT6 Cable with SMA Plug
BNC to SMA Adapter

Transducer
with BNC Connector
Figure 22: BNC to SMA Cable Adapter Installation

2.3.2 Installing C-RS or C-PT Transducers with an RG62 Cable

The AT600 flow meter can be connected directly to a C-RS or C-PT transducer with an optional RG62 cable,
which has a BNC connector at transducer end. Thus, the BNC to SMA Adapter is not needed.
This RG62 cable has a submersible cable option for the C-RS transducer. Also, there is a junction box option
for the C-RS and C-PT transducers, which provides extra physical protection for the BNC connection on the
transducer.



3.1 Wiring Diagram
ATTENTION EUROPEAN CUSTOMERS! To meet CE Mark requirements, all cables must be installed
as described in “Wiring Cable Specifications and Requirements” on page 177.
This section includes instructions for making all the necessary electrical connections to the AT600 flow
meter. Refer to Figure 23 below for the complete wiring diagram of the meter.
IMPORTANT: Except for the transducer connector, all electrical connectors are stored in their terminal blocks
during shipment and may be removed from the enclosure for more convenient wiring. Feed the
cables through the cable gland holes on the bottom of the enclosure, attach the wires to the
appropriate connectors and plug the connectors back into their terminal blocks.
After the AT600 is completely wired, proceed to “Initial Setup and Programming” on page 31 to configure the
meter for operation.
/ŶƉƵƚͬKƵƚƉƵƚdĞƌŵŝŶĂůƐ
Transducer Terminals >ĂďĞů ĞƐĐƌŝƉƟŽŶ
W/E >ĂďĞů ĞƐĐƌŝƉƟŽŶ Ϭ ŶĂůŽŐKƵƚƉƵƚ͗ϰͲϮϬŵͬ,ZdWŽƐŝƟǀĞ
ϭ E ŽǁŶƐƚƌĞĂŵdƌĂŶƐĚƵĐĞƌ ϭ ŶĂůŽŐKƵƚƉƵƚ͗ϰͲϮϬŵͬ,ZdEĞŐĂƟǀĞ
Ϯ hW hƉƐƚƌĞĂŵdƌĂŶƐĚƵĐĞƌ Ϯ ^ĞƌǀŝĐĞDŽĚďƵƐWŽƌƚWŽƐŝƟǀĞ
ϯ ^ĞƌǀŝĐĞDŽĚďƵƐWŽƌƚEĞŐĂƟǀĞ
ϰ ^ĞƌǀŝĐĞDŽĚďƵƐWŽƌƚZĞƚƵƌŶ'ƌŽƵŶĚ
ϱ ƵƐƚŽŵĞƌDŽĚďƵƐWŽƌƚWŽƐŝƟǀĞ
ϲ ƵƐƚŽŵĞƌDŽĚďƵƐWŽƌƚEĞŐĂƟǀĞ
ϳ ƵƐƚŽŵĞƌDŽĚďƵƐWŽƌƚZĞƚƵƌŶ'ƌŽƵŶĚ
ϴ ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚWŽƐŝƟǀĞ
ϵ ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚEĞŐĂƟǀĞ
ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚWŽƐŝƟǀĞ
ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚEĞŐĂƟǀĞ
Eͬ
'ĂƚĞ/ŶƉƵƚWŽƌƚWŽƐŝƟǀĞ
'ĂƚĞ/ŶƉƵƚWŽƌƚEĞŐĂƟǀĞ
& Eͬ
DETAIL A EŽƚĞ͗ŶĂůŽŐŽƵƚƉƵƚƐĂƌĞEĂŵƵƌEϰϯĐŽŵƉůŝĂŶƚ͘
GROUNDING 4
GROUNDING 3 WŽǁĞƌdĞƌŵŝŶĂůƐ
W/E >ĂďĞů ĞƐĐƌŝƉƟŽŶ
ϭ >ϭ;нͿ >;нͿ͗>ŝǀĞWŽǁĞƌͬWŽƐŝƟǀĞ
Ϯ >ϮͬE;ͲͿ E;ͲͿ͗EĞƵƚƌĂůͬEĞŐĂƟǀĞ
A
GROUNDING 2 GROUNDING 1
Figure 23: Wiring Diagram
Note: The HART and Modbus communication options must be selected when ordering the AT600.

3.1 Making the Electrical Connections (cont.)

For proper wiring, the power lines, transducer cable and I/O lines must be routed through the appropriate
cable glands (see Figure 24 below). Also, refer to “Wiring Cable Specifications and Requirements” on page 177
for the required cable specifications.
IMPORTANT: Any unused cable glands must be plugged with the cable gland inserts provided with meter.
GLAND HOLE 5 GLAND HOLE 3 GLAND HOLE 1
GLAND HOLE 4
DETAIL B
GLAND HOLE 2
CABLE GLAND HOLES

Hole Num. Feed-Through Cables
1 Power Lines
2 Digital Output B Cable Lines
Digital Output C Cable Lines
Gate Input Cable Lines
3 Service Modbus Cable Lines
Customer Modbus Cable Lines
4 Analog Output A Cable Lines
5 Transducer Cable Lines
B
Figure 24: Recommended Cable Gland Usage

3.2 Wiring the Line Power
ATTENTION EUROPEAN CUSTOMERS! To meet CE Marking requirements, all cables must be

installed as described in “Wiring Cable Specifications and Requirements” on page 177.
The AT600 may be ordered for operation with power inputs of either 85-264 VAC or 12-28 VDC. The label on
the shroud inside the electronics enclosure lists the required line voltage for your meter.
WARNING! Be sure to connect the AT600 only to the specified line voltage.
Examples of AT600 labels indicating the required line voltage are shown in Figure 25 below.
ATTENTION EUROPEAN CUSTOMERS! For compliance with the European Union's Low Voltage
Directive, this unit requires and external power disconnect device such as a switch or circuit breaker.
The disconnect device must be marked as such, clearly visible, directly accessible, and located within
1.8 m (6 ft) of the unit.
Figure 25: Typical Meter S/N Label (AC and DC Versions)

3.2 Wiring the Line Power (cont.)

Refer to Figure 23 on page 23 to locate the terminal block and connect the line power as follows:
WARNING! Improper connection of the line power leads or connecting the meter to the incorrect
line voltage will damage the unit. It will also result in hazardous voltages at the flowcell and
associated piping and within the electronics console.
1. Strip 1/4” of insulation from the end of the line and neutral AC leads (or the positive and negative DC
leads), and 1/2” of insulation from the end of the ground lead.
2. Connect the ground lead to the internal ground connection (GROUNDING 1) located on the bottom
panel of the electronics enclosure (See Figure 23 on page 23).
IMPORTANT: The incoming ground lead must be connected to the internal ground connection.
3. Connect the neutral AC lead (or the negative - DC lead) to L2/N(-) and the AC line lead (or the positive
DC lead) to L1(+), as shown in Figure 23 on page 23.
IMPORTANT: Do not remove the existing PC board ground wire or the cover ground wire.
3.3 Wiring the Transducers
ATTENTION EUROPEAN CUSTOMERS! To meet CE Mark requirements, all cables must be installed
as described in “Wiring Cable Specifications and Requirements” on page 177.
Wiring a typical AT600 system requires interconnection of the following components:

• Upstream and downstream transducers Installed in the clamping fixtures)
• The electronics console
To wire the transducers, complete the following steps:
WARNING! Before connecting the transducers, take them to a safe area and discharge any static
build-up by shorting the center conductor of the transducer cables to the metal shield on the cable
connector.
1. Locate the two transducer cables and connect them to the transducers.
2. Connect the cable connector with yellow DN jacket on the cable to the DN terminal, and connect cable
connector with white UP jacket on the cable to the UP terminal, as shown in Figure 23 on page 23.
3. Secure the cable gland.
IMPORTANT: Be sure to insert all cable connectors straight into the PCB receptacles to avoid damaging the
connector and/or the receptacle.

3.4 Wiring the System Ground
WARNING! The AT600 must always be connected to a proper earth ground, using the system
grounding screw shown in Figure 26 below.
SYSTEM GROUNDING SCREW
DETAIL C
Figure 26: System Grounding Screw
3.5 Wiring the Analog Output for HART Communication

The standard configuration of the Model AT600 flow meter includes one isolated 0/4-20mA analog output.
Connections to this output may be made with standard twisted-pair wiring. The current loop impedance for
this circuit must not exceed 600 ohms.
HART Master/
Model AT600 Ampere Meter
Volts +
(Int. Pwr. Sup.)
PIN: 0
Load
(maximum
Volts - PIN: 1
600 ohms)
(Common)
Figure 27: Analog Output/HART Communication Wiring

3.5 Wiring the Analog Output for HART Communication (cont.)
WARNING! Always be sure to disconnect the main power supply from the AT600 before proceeding
with these instructions.
To wire the analog output, refer to Figure 27 on page 27 and complete the following steps:
1. Verify that the main power has been disconnected from the unit, and then open the enclosure.
2. Install the required cable gland in the chosen gland hole on the bottom of the enclosure.
3. Refer to Figure 23 on page 23 for the location of terminal block I/O, and wire the terminal block as
shown above.
4. Secure the cable clamp.
Note the following:

• The standard analog output port provides only a 0/4-20mA analog output. If the HART
communication option is desired, it must be specified at the time of purchase.
• The AT600 analog output is an active mode type, with power provided internally by the meter. Do not
connect an external 24V power supply to this circuit.
• Prior to use, the analog output must be set up and calibrated (see “Inputs/Outputs” on page 48).
• When in meter is in configuration mode, the analog output is locked at 3.6 mA. After exiting from
configuration mode, the meter will resume normal operation.
3.6 Wiring the Modbus Communication

The optional AT600 Modbus port is a two-wire, half-duplex RS485 interface. If this option was specified at
the time of purchase, proceed with the wiring instructions below.
To wire the Modbus RS485 serial port, refer to Figure 23 on page 23 above and complete the following steps:
2. Install the required cable clamp in the chosen gland hole on the side of the electronics enclosure.
3. Route one end of the cable through the gland hole and wire it to terminal block.

3.7 Wiring the Frequency/Totalizer/Alarm Output

The AT600 can accommodate up to two digital outputs. Each of these outputs can be configured as either a
totalizer, frequency or alarm output (see “Programming Digital Communications” on page 61 for instructions).
Each totalizer/frequency/alarm output requires a twisted pair cable. Wire the terminal block as shown in
Figure 23 on page 23 and Figure 28 below.
Totalizer/Frequency Counter
Model AT600 or Alarm Detector
Max. Current: 1A
Max. Voltage: 100 V
Isolation Voltage: 500 V
Max. Load Power: 2W IN Volts +
(Int. Pwr. Sup.)
PIN: 8/A
Load
PIN: 9/B (minimum
10 Kohms)
C: Isolated Return Volts -

(Common)
Figure 28: Totalizer/Frequency/Alarm Output Wiring

3.8 Wiring the Gate Input

The AT600 provides a Gate Contact Input port. This port is designed to start/stop the totalizer. During normal
measurement mode, thee operator can start or stop the totalizer functionality by toggling the gate switch.
To wire the Gate input, refer to Figure 23 on page 23 and Figure 29 below and complete the following steps:
2. Install the required cable clamp in the chosen gland hole on the side of the electronics enclosure.
3. Route one end of the cable through the gland hole and wire it to terminal block.
Model AT600 Switch
+5 V
PIN: D
NO
PIN: E
C
Figure 29: Gate Input Wiring


4.1 Introduction
This chapter provides instructions for programming the AT600 flow meter to place it into service. Before the
AT600 can begin taking measurements, at least the following menus must be programmed:
• “User Preferences” on page 43
• “Inputs/Outputs” on page 48
• “Sensor Setup” on page 66

Refer to the Main Menu map in Figure 30 below, and proceed to the appropriate section for instructions.
Display
Main Menu
Display Format Program Program Review Keypad Lockout Language
Password
xxxx
User Preferences Input/Output Sensor Setup Calibration Advanced Factory
Save Changes?
No Yes
Display
Figure 30: Main Menu Map

4.2 AT600 Keypad Operation

There are six keys and two LEDs on the AT600 keypad. The green light is a system health indicator and is on
when the meter is operational and not in error. The red light is a system status indicator and is on when the
meter is in error. Both lights being off indicates that the system is in configuration mode or no power has
been applied to the meter.
Figure 31: The AT600 Keypad
The six keys on the keypad enable users to program the AT600:
• [] - confirms the choice of a specific option and all data entry within that option
• [] - enables users to exit from a specific option without saving unconfirmed data
• [] and [] - enable users to highlight a specific window in the display option or to scroll through a
list of options. They are also used to change individual characters in a text string.
• [] and [] - enable users to scroll to a specific menu option, or to highlight a specific character in a
text string.
When powered On, the AT600 initialization screen is shown, followed by a measurement display (see below).
Velocity
AT600 0.0 m/s
INITIALIZE . . Soundspeed
0.0 m/s
As a guide in following the programming instructions in this chapter, the complete AT600 menu maps can be
found in “Menu Maps” on page 187, and the relevant portions are reproduced throughout this chapter.
IMPORTANT: If no key has been pressed for 5 minutes, the AT600 exits the Keypad Program and returns to
displaying measurements. Any unconfirmed configuration changes are discarded.

4.3 Display Programming

The AT600 keypad has six keys (see “AT600 Keypad Operation” on page 32) and the following two LEDs:
• Green: The green LED is a system health indicator and it is On when the meter is operating without
error.
• Red: The red LED is a system status indicator and it is On whenever the meter is in error.
Note: When both LEDs are Off, the meter is either in configuration mode or no power is applied.
Total m^3
Velocity Velocity
0.0 m/s Forward 0.0
0.0 Reverse 0.0
Soundspeed
m/s
0.0 m/s
4.3.1 Changing the Display for One- or Two-Variable Screens

An outline of a typical one- or two-variable screen is shown below.
Measurement Type Velocity

Value
0.0
m/s Value Units
Error Code
To change the number of decimal places in the displayed value:
Velocity From the display screen, press either the [] or [] keys until the value is
highlighted.
0.0
m/s
Velocity After the value is highlighted, press [] to open the Display/Decimal
option.
0.0
m/s

4.3.1 Changing Display for One- or Two-Variable Screens (cont.)
Display/Decimal Use the [] and [] keys to scroll to the desired value. (Available
2 options include 0, 1, 2, 3, 4, and Sci (Scientific Notation). Press [] to
3 select the value, and then press [] again to confirm the selection or []
4 to cancel the selection.
Sci
4.3.2 Changing the Measurement Type for One- or Two-Variable Screens

To change the measurement type:
From the display screen, press either the [] or [] keys until the
Velocity measurement type is highlighted.
0.0
m/s
Velocity After the value is highlighted, press [] to open the Measurement Type
option.
0.000e+00
m/s
Measurement Type The screen changes to Display/Measurement Type. Press the [] and []
Velocity keys to scroll to the desired parameter. Available parameters include:
Act Volumetric Velocity, Act Volumetric, Std volumetric, Mass, Batch Totals, Inventory
Std Volumetric Totals, Soundspeed, Reynolds, KFactor, and Diagnostics. After you have
Mass chosen the measurement type, press [] to select the value, and then
press [] again to confirm the selection or [] to cancel the selection.
Note: To select a particular measurement unit, go to “Units Setting” on page 44.

4.3.3 Changing the Measurement Type or Units for the Totalizer Screens
The totalizer screen opens similar to Figure 32 below.
Totalizer Units Start/Stop Totalizer Reset Totalizer
Total m^3
Forward 0.000e+00
Totalizer Values
Measurement Type Reverse 0.000e+00
Error Code
Figure 32: The Totalizer Screen
To change the number of decimal places in the value displayed on a totalizer screen, proceed as follows:
TOTAL m^3 From the display screen, press either the [] or [] keys until the value
is highlighted.
Forward 0.000e+00
Reverse 0.000e+00
Total m^3 After the value is highlighted, press [] to open the Display/Decimal option.
Forward 0.000e+00
Reverse 0.000e+00
Display/Decimal Use the [] and [] keys to scroll to the desired number of decimal
2 places. (Available options include 0, 1, 2, 3, 4, and Sci (Scientific Notation).
3 Press [] to select the value, and then press [] again to confirm the
4 selection or [] to cancel the selection.
Sci

4.3.3 Changing the Measurement Type or Units for the Totalizer Screens (cont.)
To change the totalizer measurement type, proceed as follows:
TOTAL m^3 From the display screen, press either the [] or [] keys until the
measurement type is highlighted.
Forward 0.000e+00
Reverse 0.000e+00
Total m^3 After the type is highlighted, press [] to open the Display/Decimal option.
Forward 0.000e+00
Reverse 0.000e+00
Totalizer Type The screen changes to Totalizer Type. Press the [] and [] keys to scroll to
Forward Totals the desired parameter. Available parameters include: Forward Totals,
Reverse Totals Reverse Totals, Net Totals and Time. After you have chosen the type, press
Net Totals [] to select the value, and then press [] again to confirm the selection or
Time [] to cancel the selection.
If the first value is set to Time, the meter displays the time unit. If the first value is set to Forward Totals,
Reverse Totals, or Net Totals, the meter displays the selected unit in the Units Setting selection. The available
time measurement units are seconds, minutes, hours or days. To choose the appropriate units, from the
highlighted measurement type, press the [] or [] keys until the desired measurement unit is highlighted.
TOTAL Seconds After the unit is highlighted, press [] to open the Display/Unit option.
Time 0.0000
Reverse 0.000e+00
Display/Unit Press the [] and [] keys to scroll to the desired units, and press [] to
Seconds select the unit, and then press [] again to confirm the selection or [] to
Minutes cancel the selection.
Hours Note: If you selected Time, the available units are seconds, minutes, hours
Days and days.

4.3.4 Starting or Stopping the Totalizer Measurement

To start or stop totalizer measurements:
From the display, press either the [] or [] keys until the Start/Stop icon
TOTAL m^3
(either an arrow icon for Start or a two-bar icon for Stop) is highlighted.
Forward 0.000e+00
Reverse 0.000e+00
TOTAL m^3 After the value is highlighted, press [] to start or stop totalizing.
Forward 0.000e+00
Reverse 0.000e+00
TOTAL m^3 The display icon then changes to indicate the new status (Start or Stop).
Forward 0.000e+00
Reverse 0.000e+00

4.3.5 Resetting the Totalizer

To reset the totalizer, proceed as follows:
TOTAL m^3 From the display screen, press either the [] or [] keys until the Reset
Forward 0.000e+00 icon (a partial circle with an arrow) is highlighted.
Reverse 0.000e+00
TOTAL m^3 After the Reset icon has been highlighted, press [] to reset the totalizer to 0.
Forward 0.000e+00
Reverse 0.000e+00

4.4 Entering the Main Menu
Display
Locked
Esc > Enter > Esc Unlocked
Main Menu
1 Variable Yes English ѝ᮷
2 Variables No Deutsch Français
Totalizer Italiano ᰕᵜ䃎
Português ƴǗǕǕǎǌǍ
Española Svenska
Turkish
Figure 33: The Main Menu Map
4.4.1 Display Format

To begin programming your meter, you must select the system units as discussed below. Remember to
record all programming data in Appendix B, Data Records.
The Display Format submenu is used to set up the type of format to be used in displaying information.
On the initial screen, use the arrow keys to highlight the lock symbol
Velocity and press [√].
0.0 The following screen opens.

m/s

4.4.1 Display Format (cont.)
Display Use the [] or [] keys to highlight Display Format and press []. The
Display Format following screen opens.
Program
Program Review
Keypad Lockout
Use the [] and [] arrow keys to highlight the desired format setup and
Display/Display Format press [] to return to the previous screen.
One Variable
Two Variable
Totalizer
4.4.2 Keypad Lockout
Display To lock or unlock the keypad for security, on the Display menu, select
Keypad Lockout and press []. A screen similar to the following opens.
Display Format
Program
Program Review
Keypad Lockout
To lock the display, use the [] and [] keys to highlight Yes and press
Lockout/ Keypad Lockout
[]. The screen returns to the previous display.
No
Yes To unlock the display, use the [] and [] keys to highlight No and press
[]. The screen returns to the previous display.
Note: When the keypad is locked, press [], [], [] to unlock it.

4.4.3 Language
Display To change the display language, on the Display menu, select Language and
Program press [√]. A screen similar to the following opens.
Program Review
Keypad Lockout
Language
Display/Language Use the [] and [] arrow keys to highlight the desired language and
English press [√] to return to the previous screen. The display language is
Deutsch changed to the new selection.
中文
Français
4.4.4 Program and Program Review Menus

The Program and Program Review menus allow setting up or viewing of several categories of information. As
discussed, to edit parameters, you need to input a valid password. The next section describes the access
levels required to edit various parameters. To view all parameters without editing, select Program Review.
Display
Main Menu
Password
xxxx
User Preferences Input/Output Sensor Setup Calibration Advanced Factory
Save Changes?
No Yes
Display
Figure 34: Program and Program Review Menu Map

4.4.4.1 Program Review

The Program Review menu requires no user password. However, it provides view-only access to the
information. To change any setting or parameter, you must enter the Program Menu by entering a valid
password.
4.4.4.2 Program
IMPORTANT: When you enter Program (configure) mode, measurements stop and the output goes to error level.
Display To enter the Programming menu, on the Display menu use the arrow keys
Display Format
to highlight Program and press [√]. The following screen opens.
Program
Program Review
Keypad Lockout
Enter the password Use the [] or [] key to select a specific digit, then use the [] or [] key
to change that digit as required. After all digits are correct, press [] to
9999 open the User Preference screen.
]
]UNDO [ ]SAVE
]
]MOVE
]
]MODF Note: The default password is 1111.

4.5 User Preferences

4.5.1 Setting
User Preference To check or change the desired settings, under User Preference, select
Setting Settings and press []. The following screen opens.
Units Setting
Density
Password
Setting To check the Meter Tag and/or Label, highlight your choice on the Setting
Meter Tag menu and press []. Press [] to return to the previous screen.
Label Note: You can only change the Meter Tag and Label data using BHGE’s
System Date
Vitality software.
Setting To check or change the date/time, highlight System Date and press []. The
Meter Tag following screen opens.
Label
System Date
Set System Time Use the [] or [] key to select a specific digit, then use the [] or [] key
Date: 11 / 12 / 2013 to change that digit as required. After all digits are correct, press [] to
Time: 08 : 09 : 10 save. Then, press [] to return to the previous screen.
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

4.5.2 Units Setting
User Preference To check or change velocity flow units, use the [] or [] arrow key to
Settings select Units Setting and press []. The following screen opens.
Units Setting
Density
Password
Units Setting Under Units Setting menu, use the [] or [] arrow key to select the unit
Velocity that need to be changed and press [√] to open the following screen.
Act Volumetric Note: Velocity is shown here as a typical example.
Std Volumetric
Mass
UnitsSet / Velocity If you don’t want to change the selected unit, select No and press []. If
No you do want to change the selected unit, select Yes, then press[] twice to
Yes open the following screen.
UnitsSet /Velocity If no change is desired, press [] twice to return to the Units Setting menu.
English To change the measurement system, select the desired option, press []
Metric twice to open a screen similar to the following.
Confirm the selected units, press [] three times to return to the Units
Vel / Setting menu.
Ft/s

4.5.3 Density
User preference To configure flow density, use the [] or [] arrow key to select Density
Settings and press []. The following screen opens.
Units Setting
Density
Password
Density Use the [] or [] arrow keys to highlight the desired density type and
Density (Act) press [√].
Density (Std)
Density Press [√] again and a screen similar to the following opens.
Density (Act)
1000.000 Kg/m^3
Density (Act) Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: Kg/m^3 to change that digit as required. After all digits are correct, press [] to
1000.000 save. Then, press [] to return to the previous screen.
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

4.5.4 Password
User preference To set up a password, use the [] or [] arrow key to select Password and
Setting press [√]. The following screen opens.
Units Setting
Density
Password
9999 save. Then, press [] to return to the previous screen.
]
]UNDO [ ]SAVE
]
]MOVE
]
]MODF The default password is 1111.
4.5.5 Display
4.5.5.1 Backlight
User preference To turn the backlight OFF or ON, use the [] or [] arrow key to select
Units Setting Display and press [√]. The following screen opens.
Density
Password
Display
Display Select Backlight, and press [√] to open a screen similar to the following.
Backlight
Timeout
Display/Backlight Select OFF or ON, and press [√] twice to return to the previous screen.
OFF
ON

4.5.5.2 Timeout
Display To provide a timeout, select Timeout and press [√]. A screen similar to the
Backlight following opens.
Timeout Note: The default value for the timeout is 0.
Timeout Press [√] again, and a screen similar to the following opens.
Timeout
19 S
Timeout Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: S to change that digit as required. After all digits are correct, press [] to
19 save. Then, press [] three times to return to the User Preference screen.
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

4.6 Inputs/Outputs
4.6.1 Programming the Analog Output Menu
To access the Analog Output menu, on the initial screen, highlight the
Velocity lock symbol and press [√]. The following screen opens.
0.0
m/s
Display Select Program and press [√]. The following screen opens.
Display Format
Program
Program Review
Keypad Lockout
9999 save. The following screen opens.
]
]UNDO [ ]SAVE
]
]MOVE
]
]MODF
User Preference Select Input/Output and press the [] key. A screen similar to the following
Settings opens.
Units Setting
Density
Password
Input/Output Select the desired Output with the [] or [] arrow keys, and press [] to
Analog Output A enter the configuration menu.
Digital Output B
Digital Output C
Modbus/Service Port

4.6.1.1 Setting the Analog Measurements
Input/Output Select the desired Output with the [] or [] arrow keys, and press [] to
Analog Output A enter the configuration menu.
Digital Output B
Digital Output C
Modbus/Service Port
Analog Output A Select Measurement and press []. The following screen opens.
Measurement
Base Value
Full Value
Calibrate
Measurement In the Measurement menu, select the type of analog output to be used, and
Velocity press [√] to return to the previous screen.
Act Volumetric
Std Volumetric
Mass
4.6.1.2 Setting the Base Value and the Full Value
Analog Output A Base Value is the flow rate represented by a 4 mA output signal, and Full
Measurement Value is the flow rate represented by a 20 mA output signal. In the Analog
Base Value Output menu, select Base Value or Full Value and press []. A screen similar
Full Value to the following opens.
Calibrate
Base Value Press [] again and a screen similar to the following opens.
Base Value Note: The units shown are the units selected in the Units Setting menu.
0.0000 m/s
Base Value Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: m/s to change that digit as required. After all digits are correct, press [] to
0.0000 save. Then, press [] to return to the previous screen. Repeat these steps
]
]UNDO [ ]SAVE to set the Full Value setting, and press [] to return to the Analog Output A
]
]MOVE [ ]MODF
menu.

4.6.1.3 Calibrate the Output
Analog Output A Use the Calibrate menu to trim the analog output. In the Analog Output
Measurement menu, select Calibrate and press []. A screen similar to the following
Base Value opens.
Full Value
Calibrate
Calibrate Select either 4 mA to trim the 4 mA level, 20 mA to trim the 20 mA level,

Calibrate 4mA or Percentage of Scale to test the output linearity. Select the desired
Calibrate 20mA option and press []. A screen similar to the following opens.
Percentage of Scale
Calibrate 4mA Read the analog output with a digital multimeter, and enter that value.
UNIT: mA Use the [] or [] key to select a specific digit, then use the [] or [] key
4.000 to change that digit as required. After all digits are correct, press [] to
save. Then, press [] to return to the previous screen. Repeat these steps
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF until the actual output value matches the programmed value.
4.6.1.4 Setting Error Handling
Analog Output A To specify the error handling status in the Analog Output A menu, select
Base Value Error Handling and press []. The following screen opens.
Full Value
Calibrate
Error Handling
Calibrate During an error condition, selecting Low forces the Analog Output to 3.6
Low mA or below, while selecting High forces it to 21.6 mA or above. HOLD
High keeps the last good value during an error condition. Select the desired
Hold setting and press [].
Other

4.6.2 Programming the Digital Output Menu
To access the Digital Output menu, on the initial screen, highlight the
Velocity lock symbol and press [√]. The following screen opens.
0.0
m/s
Display Format
Program
Program Review
Keypad Lockout
]
]UNDO [ ]SAVE
]
]MOVE
]
]MODF
User Preference In the User Preference menu, select Units Setting and press the right arrow
Settings key. A screen similar to the following opens.
Units Setting
Density
Password
Input/Output Select the desired Digital Output with the [] or [] arrow keys, and press
Analog Output A [] to enter the relevant configuration menu.
Digital Output B Note: The programming steps for Digital Output B and Digital Output C are
Digital Output C the same as those for Digital Output A.
Modbus/Service Port
Digital outputs can be programmed as Pulse, Frequency or Alarm, or they can be turned Off.

4.6.2.1 Disable the Digital Output
Digital Output B To disable Digital Output B, select Off in the menu and press [] twice.
Off
Pulse
Frequency
Alarm
4.6.2.2 Setting the Pulse Output
Digital Output B The Pulse output generates a square wave pulse for each unit of flow that
Off passes through the pipeline. Select Pulse and press [] to open the
Pulse following screen.
Frequency
Alarm
Setting the Measurement Type
Pulse Select Measurement and press [] to open the following screen.
Measurement
Pulse Value
Pulse Time
Test Pulse
Forward Batch Total press [] to return to the previous screen.
Reverse Batch Total
Net Batch Total

Setting the Pulse Value
Pulse Use the [] or [] arrow keys to select Pulse Value and press []. A screen
Measurement similar to the following opens.
Pulse Value
Pulse Time
Test Pulse
Pulse Value The Pulse Value is the amount of flow represented by one pulse in the
Pulse Value display. (e.g., 1 pulse = 10 m^3.) To change the existing setting, press []
10.0000 m^3 and a screen similar to the following opens.
Note: The units shown are the units selected in the Units Setting menu.
Pulse Value Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: m^3 to change that digit as required. After all digits are correct, press [] to
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
Setting the Pulse Time
Pulse Use the [] or [] arrow keys to select Pulse Time and press []. A screen
Pulse Value
Pulse Time
Test Pulse
Pulse Time The Pulse Time (i.e., the pulse width) is displayed. To change the existing
Pulse Time setting, press [] and a screen similar to the following opens.
5 ms
Pulse Time Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: ms to change that digit as required. After all digits are correct, press [] to
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

Totalizer Pulse Setting Guidelines

When programming the pulse totalizer, a smaller pulse value generally results in higher totalizer accuracy.
However, the minimum practical pulse value is limited by the resolution of the pulse counter being used.
Thus, one must find the proper balance between the desire for a small pulse value and the capability of the
pulse counter to accurately read the pulses output by the AT600.
The best way to illustrate this process is with the following example calculation:
• The parameters set on the previous page are the Pulse Value (PV = the volume of flow per pulse) and
the Pulse Time (PT = the width of each pulse).
• Program the Pulse Measurement as a Forward Batch Totalizer.
• Consider a process where the volumetric flow rate (VR) fluctuates near 4.6 liter/sec.
• As a typical value, try a PV of VR/20 = 4.6/20. Thus, set PV = 0.23 liter/pulse.
• Then, the duration of each pulse is PV/VR = 0.23/4.6 = 50 ms. As the Pulse Time (PT) is defined as half
the pulse duration, then the correct PT = 25 ms.
• Program the AT600 frequency output with PV = 0.23 liters/pulse and PT = 25 ms. If your frequency
counter correctly reads the AT600 pulse output, then these settings are appropriate. If not, you need
to try different calculations for PV (instead of VR/20) until you find a set of values that can be
properly read by your frequency counter. In general, the smallest PV value that is within the
resolution specification for your frequency counter will provide the best accuracy for the batch
totalizer.

Setting the Pulse Error Handling
Pulse To change the Error Handling status of the pulse output, select Error
Pulse Value Handling in the menu and press []. The following screen opens.
Pulse Time
Test Pulse
Error Handling
Error Handling Select Hold or Stop. In case of a flow measurement error, Hold directs the
Stop meter to keep sending the same pulses sent at the last good reading. Stop
Hold directs the meter to stop sending pulses during the error condition. Press
[] to return to the previous display or press [] to return to the Digital
Output menu.
Test the Pulse
Pulse To test the pulse output, select Test Pulse and press []. The following
Pulse Value screen opens.
Pulse Time
Test Pulse
Error Handling
Test Pulse Press [] to open a screen similar to the following. Press [] again and the
Test Pulse screen returns to the previous display. Press [] to return to the Digital
0 Output menu.
Test Pulse Use the [] or [] key to select a specific digit, then use the [] or [] key
0 save. Verify on your frequency counter that the correct number of pulses
were received. After testing is complete, press [] to return to the Digital
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF Output menu.

4.6.2.3 Setting the Frequency
Digital Output B Frequency sends out a continuous square wave, with a frequency
Off proportional to the measured flow rate. Select Frequency and press [] to
Pulse open the following screen.
Frequency
Alarm
Setting Measurement Type
Frequency Select Measurement and press [] to open a screen similar to the
Measurement following.
Base Value
Full Value
Full Frequency
Measurement In the Measurement menu, select the type of analog output to be used and
Velocity press [] to return to the previous screen.
Act Volumetric
Std Volumetric
Mass
Setting the Base Value, Full Value, and Frequency
Frequency The Base Value is the measurement that corresponds to a 0 Hz pulse. The
Measurement Full Value is the measurement value that corresponds to a Full Frequency
Base Value pulse. The Full Frequency is the maximum frequency used for the output
Full Value pulse, and it indicates the maximum flow rate measurement. Use the []
Full Frequency or [] arrow keys to select the appropriate option and press[]. A screen
similar to the following opens.
Note: Use the same steps to program the Base Value, Full Value and Full
Frequency.
Base Value To change the existing number, press [] and a screen similar to the
Base Value following opens.
0.0000 m/s

Setting the Base Value, Full Value, and Frequency (cont.)
Base Value Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
Setting the Frequency Error Handling
Frequency To change the Error Handling status, select Error Handling in the menu and
Full Value press []. The following screen opens.
Full Frequency
Test Frequency
Error Handling
Error Handling To change the current Error Handling status, select the desired option, and
Low press []. The screen returns to the previous display.
High There are four options for response to an error situation:
Hold
Other • Hold: hold the last good value
• Low: display 0 Hz
• High: display the Full Frequency
• Other: If selected, a screen similar to the following opens
Error Handling Value Enter the frequency value you want to display during an error situation.
Value (e.g., if Full Frequency = 1 kHz, you may want to set the Error Handling Value
0 Hz to 2 kHz.) Press [] again, and a screen similar to the following opens.
Test Frequency Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: Hz to change that digit as required. After all digits are correct, press [] to
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

The Test Frequency
Frequency To test the Frequency output, select Test Frequency and press []. The
Full Value following screen opens.
Full Frequency
Test Frequency
Error Handling
Test Frequency Press [] to open a screen similar to the following.

Test Frequency
0 Hz
Test Frequency Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: Hz to change that digit as required. After all digits are correct, press [] to
0 save. Then, verify at your frequency counter that you see the frequency
]
]UNDO [ ]SAVE you entered. If desired, you can repeat this procedure with several
]MOVE [ ]MODF different frequencies. After testing is complete, press [] to return to the
]
Digital Output menu.
4.6.2.4 Setting the Alarm
Digital Output B The alarm can be either an open circuit (normally closed type) or a short
Off circuit (normally open type), depending on the error condition. To check
Pulse the alarm or change its settings, in the Digital Output menu select Alarm
Frequency and press []. The following screen opens.
Alarm

Setting the Measurement Type
Alarm Select Measurement and press []. A screen similar to the following opens.
Measurement
Alarm State
Alarm Type
Alarm Value
Velocity press []. The screen returns to the previous display.
Act Volumetric
Std Volumetric
Mass
Setting the Alarm State
Alarm Use the [] or [] arrow keys to select Alarm State and press[]. A screen
Alarm State
Alarm Type
Alarm Value
Alarm State Two alarm states are available:

Normal
Fail Safe • Normal: Normally open, the alarm contacts close in an error condition
• Fail Safe: Normally closed, the alarm contacts open upon in an error
condition or a power failure
To change the state of the alarm, select the desired status and press [],.
The screen returns to the previous display.

Setting the Alarm Type
Alarm Use the [] or [] arrow keys to select Alarm Type and press []. A screen
Alarm State
Alarm Type
Alarm Value
Alarm Type You can choose from three alarm types:

Low
High • Low: the alarm trips only if the measurement falls to or below the threshold
Fault value
• High: the alarm trips if the measurement rises to or exceeds the threshold
value
• Fault: the alarm trips only for system errors, such as a power failure
To change the type of alarm, select the desired type and press [] to return
to the previous screen.
Setting the Alarm Value
Alarm The Alarm Value is the threshold that trips a Low or High alarm. To check
Alarm State or change the alarm value, select Alarm Value and press []. A screen
Alarm Type similar to the following opens.
Alarm Value
Test Alarms
Alarm Value Press [] again, and a screen similar to the following opens.
Alarm Value
10.000 m/s
Alarm Value Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

Test the Alarms
Alarm To test the Alarms output, select Test Alarms and press []. The following
Alarm State screen opens.
Alarm Type
Alarm Value
Test Alarms
Error Handling Select OFF to disable the alarm or ON to enable the alarm. To begin
OFF testing, select ON and press []. To stop testing, press [].
ON
]
]UNDO [ ]SAVE
4.6.3 Programming the Modbus/Service Port
Input/Output The Modbus/Service port is configured at the factory as follows:

Analog Output A • Baud Rate = 115200
Digital Output B
Digital Output C • Bits/Parity = 8/None
Modbus/Service Port • Stop Bits = 1
• Address = 1
To view the settings for the Modbus/Service Port, select it on the
Input/Output screen and press [].
4.6.4 Programming Digital Communications

The AT600 flow meter supports the following digital communication types:
• Modbus
• HART
A password is required to activate the digital communications options. In case of problems, contact BHGE for
assistance.

4.6.4.1 Modbus
Input/Output To set up Modbus, select Digital Comm on the Input/Output screen and press
Digital Output B []. The following screen opens.
Digital Output C
Modbus/Service Port
Digital Comm
Digital Comm Press [] again, and a screen similar to the following opens.
MODBUS
Selecting the Baud Rate
MODBUS To set the baud rate, select Baud Rate and press []. A screen similar to
Baud Rate the following opens.
Address
Bits/Parity
Stop Bits
Baud Rate The default baud rate is 115200. To change the default, select the desired
19200 baud rate and press [] to return to the previous screen.
38400
57600
115200

Selecting the Modbus Address
MODBUS To set the address, select Address and press []. A screen similar to the
Baud Rate following opens.
Address
Bits/Parity
Stop Bits
Address Press [] again, and a screen similar to the following opens.
Address
1
Address The default Address is 1, but 1 to 254 are the acceptable values. Use the
[] or [] key to select a specific digit, then use the [] or [] key to
1 change that digit as required. After all digits are correct, press [] to save.
Then, press [] to return to the previous screen.
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
Selecting the Bits/Parity
MODBUS To set the Bits/Parity, select Bits/Parity and press []. A screen similar to the
Baud Rate following opens.
Address
Bits/Parity
Stop Bits
Bits/Parity The default Bits/Parity is 8/None. Select the desired setting and press [] to
8/None return to the previous screen.
8/Odd
8/Even
115200

Selecting the Stop Bits
MODBUS The default Stop Bits is 1. To set the Stop Bits, select Stop Bits and press [].
Baud Rate A screen similar to the following opens.
Address
Bits/Parity
Stop Bits
Stop Bits Select the desired setting and press [] to return to the previous screen.
1
2
115200
4.6.4.2 HART
Input/Output To set up HART communication, select Digital Comm on the Input/Output

Digital Output B screen and press []. The following screen opens.
Digital Output C Note: Verify that the HART function is installed and activated on your
Modbus/Service Port meter.
Digital Comm
Digital Comm Press [] again, and a screen similar to the following opens.
HART

Setting the HART Address
HART To set the HART address, select Address and press []. A screen similar to
Address the following opens.
Address Press [] again, and a screen similar to the following opens.
Address
0
Address The default setting is 0. Use the [] or [] key to select a specific digit,
then use the [] or [] key to change that digit as required. After all
0 digits are correct, press [] to save. Then, press [] to return to the
]
]UNDO [ ]SAVE previous screen.
]
]MOVE [ ]MODF

4.7 Sensor Setup
To access the Sensor Setup menu from the measurement display,

Velocity highlight the lock symbol and press [√]. The following screen opens.
0.0
m/s
Display Format
Program
Program Review
Keypad Lockout
]
]UNDO [ ]SAVE
]
]MOVE
]
]MODF
User Preference In the User Preference menu, select Units Setting and press the [] key
Settings twice. A screen similar to the following opens.
Units Setting
Density
Password
Sensor Setup Select the desired parameter with the [] or [] arrow keys, and press
Meter Setup [] to enter the configuration menu.
Mounting Type
Pipe
Transducer

4.7.1 Meter Setup

4.7.1.1 Setting the Zero Cutoff
Near zero flow rate, the readings may fluctuate due to small offsets caused by thermal drift or similar
factors. To force a Zero display reading when there is minimal flow, enter a Zero Cutoff value as described
below.
Sensor Setup Select Meter Setup and press [√]. The following screen opens.
Meter Setup
Mounting Type
Pipe
Transducer
Meter Setup Select Zero Cutoff and press [√]. The following screen opens.
Zero Cutoff
Meter Setup/Zero Cutoff Press [] again, and a screen similar to the following opens.
Zero Cutoff Note: The units shown are the units selected in the Units Setting menu.
0.05 m/s
Zero Cutoff Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF

4.7.2 Mounting Type

4.7.2.1 Setting the Mounting Type
Sensor Setup Select Mounting Type and press [√]. The following screen opens.
Meter Setup
Mounting Type
Pipe
Transducer
Mounting Type Select Clamp-on if need and press [√] to return to the previous screen.
Clamp-on
Wetted
Mounting Type Select Wetted if need and press [√] to return to the previous screen.
Clamp-on
Wetted

4.7.3 Programming the Pipe Menu when Wetted selected

4.7.3.1 Setting the Pipe OD, ID, and Wall Thickness
Sensor Setup Select Pipe and press [√]. The following screen opens.
Meter Setup
Mounting Type
Pipe
Transducer
Pipe In the Sensor Setup menu, select Pipe OD, Pipe ID or Wall Thickness and
Pipe OD
press [√]. A screen similar to the following opens.
Pipe ID
Wall Thickness
Pipe Material
Pipe OD Press [√] again, and a screen similar to the following opens.
Pipe OD
89.760 mm
Pipe OD Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: mm to change that digit as required. After all digits are correct, press [] to
to enter the Pipe ID and Wall Thickness. Then, press [] to return to the
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF Pipe menu.
IMPORTANT: Changing the Pipe ID (Inside Diameter) automatically changes the Wall Thickness. Similarly,
changing the Wall Thickness automatically changes the Pipe ID.

4.7.4 Programming the Pipe Menu when Clamp-on selected

4.7.4.1 Setting the Pipe OD, ID, and Wall Thickness
Sensor Setup Select Pipe and press [√]. The following screen opens.
Meter Setup
Mounting Type
Pipe
Transducer
Pipe In the Sensor Setup menu, select Pipe OD, Pipe ID or Wall Thickness and
Pipe OD press [√]. A screen similar to the following opens.
Pipe ID
Wall Thickness
Pipe Material
Pipe OD Press [] again, and a screen similar to the following opens.
Pipe OD Note: The units shown are the units selected in the Units Setting menu.
89.760 mm
Pipe OD Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE to enter the Pipe ID and Wall Thickness. Then, press [] to return to the
]
]MOVE [ ]MODF
Pipe menu.
IMPORTANT: Changing the Pipe ID (Inside Diameter) automatically changes the Wall Thickness. Similarly,
changing the Wall Thickness automatically changes the Pipe ID.

4.7.4.2 Selecting the Pipe Material
Pipe In the Pipe menu, select Pipe Material and press [√]. The following screen
Pipe OD opens.
Pipe ID Note: Table 3 below lists the available pre-programmed pipe materials.
Wall Thickness
Pipe Material
Table 3: Pre-programmed Pipe Materials

Name Pipe Material
CARBON STEEL Carbon Steel
SS STEEL Stainless Steel
DUCT IRON Duct Iron
CAST IRON Cast Iron
Cu Cuprum
Al Aluminum
BRASS Brass
30%Ni 30% Nickel Copper Alloy
10%Ni 10% Nickel Copper Alloy
PYREX GLASS Pyrex Glass
FLINT GLASS Flint Glass
CROWN GLASS Crown Glass
NYLON PLSTC Nylon Plastic
POLYE PLSTC Polyethylene
POLYP PLSTC Polypropylene
PVC PLSTC Polyvinyl chloride
ACRYL PLSTC Acrylic Plastic
Pipe Material Select the appropriate pipe material from the list, and press [] to return
CuNi to the previous screen. If your pipe material is not listed, select Other and
Glass press [√] twice. A screen similar to the following opens.
Plastic
Other

4.7.4.2 Setting the Pipe Material (cont.)
Pipe SOS Press [] again, and a screen similar to the following opens.
Pipe SOS Note: The units shown are the units selected in the Units Setting menu.
2400.000 m/s
Pipe SOS Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
4.7.4.3 Setting the Pipe Lining
Pipe In the Pipe menu, select Lining and press [√]. The following screen opens.
Pipe ID
Wall Thickness
Pipe Material
Lining
Lining If there is no lining in your pipe, select No and press [√] to return to the
No previous screen. If your pipe does have a lining, select Yes and press [√]
Yes twice. A screen similar to the following opens.
Lining To set the lining thickness, select Lining Thickness and press []. A screen
Lining Thickness similar to the following opens.
Lining Material

4.7.4.3 Setting the Pipe Lining (cont.)
Lining Thickness Press [] again, and a screen similar to the following opens.
Lining Thickness
0.000 mm Note: The units shown are the units selected in the Units Setting menu.
Lining Thickness Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
Lining Material Select Lining Material and press [], then select the appropriate option and
MORTR press []. If your pipe material is not listed (see Table 4 below for the
RUBBR available options), select Other and press [√] twice. A screen similar to the
REFLN following opens.
Other
Table 4: Pre-Programmed Pipe Lining Materials

Name Lining Material
Tar Epoxy Tar Epoxy
Pyrex Glass Pyrex Glass
Asbestos Cement Asbestos Cement
Mortar Mortar
Rubber Rubber
Teflon Teflon (PFTE)

4.7.4.3 Setting the Pipe Lining (cont.)
Lining SOS Press [] again, and a screen similar to the following opens.
Lining SOS Note: The units shown are the units selected in the Units Setting menu.
2000.000 m/s
Lining SOS Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
4.7.5 Programming the Transducer when Clamp-on selected

4.7.5.1 Entering a Standard Transducer
Sensor Setup Select Transducer and press [√]. The following screen opens.
Meter Setup
Mounting Type
Pipe
Transducer
Transducer Select STD and press [√]. A screen similar to the following opens.
STD
SPEC
SPEC

4.7.5.1 Entering a Standard Transducer (cont.)
STD Press [] again, and a screen similar to the following opens.
STD
SPEC 0
STD Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF Note: The available AT600 standard transducers are listed in Table 5
below.
Table 5: Standard Transducer Types

Transducer Number Transducer Type
10 CPT-0.5CPT-0.5
11 CPT-2.0
12 CPT-0.5-MT C-PB-05-M
13 CPT-1.0-MT C-PB-10-M
14 CPT-2.0-MT C-PB-20-M
15 CPT-0.5-HT
16 CPT-1.0-HT
17 CPT-2.0-HT
18 CPS-0.5
19 CPSM-2.0
20 CTS-1.0
21 CTS-1.0-HT
22 CTS-2.0
23 C-LP-40-HM
24 C-LP-40-NM
25 CPB-0.5-HT
26 CPB-2.0-MT
27 CPB-0.5-MT
28 CPB-2.0
29 CPB-0.5
30 CPS-1.0 CPT-1.0

Table 5: Standard Transducer Types (cont.)

31 CWL-2
32 CPS-1.0
33 CPW (WT-1P-1.0 on AB82
34 CPW (WT-1P-0.5 on NDT plastic
35 CPW (WT-1P-1.0 on NDT plastic
36 CPB-1.0-HT
37 CPB-2.0-HT
38 CPB-1.0
39 CPB-1.0-MT
301 C-RL-0.5
302 C-RL-1
304 C-RL-0.5
305 C-RL-1
307 C-RL-0.5
308 C-RL-1
310 C-RV-0.5
311 C-RV-1
313 C-RW-0.5
314 C-RW-1
401 C-RS-0.51
402 C-RS-1 1
403 C-RS-2
407 UTXDR-2
408 UTXDR-5
601 CAT-0.5
602 CAT-1
603 CAT-2 1
1
Currently supported transducer

4.7.5.2 Entering a Special Transducer
Meter Setup
Mounting Type
Pipe
Transducer
Transducer Select SPEC and press [√]. A screen similar to the following opens.
STD
SPEC
Special Transducer In the Special Transducer menu, select Frequency and press [√]. The
Frequency following screen opens.
Wedge Angle
Wedge SNSD
Time Wedge
Frequency Select the appropriate option and press [] twice to return to the previous
0.5 Mhz screen.
1 Mhz
2 Mhz
4 Mhz

Special Transducer Select Wedge Angle and press [√]. The following screen opens.
Frequency
Wedge Angle
Wedge SNSD
Time Wedge
Wedge Angle Press [] again, and a screen similar to the following opens.
Wedge Angle
42
Wedge Angle Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
Special Transducer Select Wedge SNSD and press [√]. The following screen opens.
Frequency
Wedge Angle
Wedge SNSD
Time Wedge

4.7.5.2 Entering a Special Transducer (cont.)
Wedge SNSD Press [] again, and a screen similar to the following opens.
Wedge SNSD
2482 m/s
Wedge SNSD Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF
Special Transducer Select Time Wedge and press [√]. The following screen opens.
Frequency
Wedge Angle
Wedge SNSD
Time Wedge
Time Wedge Press [] again, and a screen similar to the following opens.
Time Wedge
7.500 us
Time Wedge Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: us to change that digit as required. After all digits are correct, press [] to
]
]UNDO [ ]SAVE
]MOVE [
]
]MODF

4.7.6 Programming the Transducer when Wetted selected

4.7.6.1 Entering a Standard Transducer
Meter Setup
Mounting Type
Pipe
Transducer
Transducer Select STD and press [√]. A screen similar to the following opens.
STD
SPEC
SPEC
STD Press [] again, and a screen similar to the following opens.
STD
SPEC 0
STD Use the [] or [] key to select a specific digit and change that digit as
required. After all digits are correct, press [] to save. Then, press [] to
0 return to the previous screen.
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF Note: The available AT600 standard transducers are listed in Table 6
below.
Table 6: Standard Wetted Transducer Types

40 WT-1/1P-10-00-NT
44 WT-1/1P-05-00-NT
71 PA-36-1P/WT-1/1P-10-00
72 PA-36-1P/WT-1/1P-10-00-HL
73 PA-PV-1P or F/WT-1/1P-10-EW
74 PA-36-1P-EW/WT-1/1P-10
75 PA-36-1P-EW/WT-1/1P-10-00-HL

Meter Setup
Mounting Type
Pipe
Transducer
Transducer Select SPEC and press [√]. A screen similar to the following opens.
STD
SPEC
Special Transducer In the Special Transducer menu, select Frequency and press [√]. The
Frequency following screen opens.
Time Wedge
Frequency Select the appropriate option and press [√] twice to return to the previous
0.5 Mhz screen.
1 Mhz
2 Mhz
4 Mhz
Special Transducer Select Time Wedge and press [√]. The following screen opens.
Frequency
Time Wedge

4.7.6.2 Entering a Special Transducer (cont.)
Time Wedge Press [√] again, and a screen similar to the following opens.
Time Wedge
7.500 us
Time Wedge Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: us to change that digit as required. After all digits are correct, press [] to
]
]UNDO [ ]SAVE
]MOVE [
]
]MODF

4.7.7 Programming the Number of Traverses
1 Traverse 3 Traverse
XDR XDR
XDR XDR
2 Traverse 4 Traverse
XDR XDR XDR XDR
Figure 35: Examples of 1 to 4 Traverses
Sensor Setup Select Traverses and press [√]. The following screen opens.
Mounting Type
Pipe
Transducer
Traverses
Traverses Select the appropriate option and press [] to return to the previous
1 screen.
2
3
4

4.7.8 Programming the Fluid Type

If the fluid type is known, the meter performs flow rate calculations based on the programmed parameters
for that fluid. However, if the fluid type is not known, you must activate the Tracking Windows function
described below. Relocating the transducers is not necessary.
Sensor Setup Select Fluid Type and press [√]. The following screen opens.
Traverses
Fluid Type
Fluid Temperature
Path
Fluid Type If the fluid type is water, select Water and press [] to return to the
Water previous screen.
Other
If the fluid is not water, select Other and press []. A screen similar to the
following opens.
Tracking Window To disable the tracking window, select No and press []. A screen similar
No to the following opens, so that you can enter the speed of sound (Fluid
Yes SOS.) in your fluid. If you don't know your Fluid SOS, you should enable
the Tracking Window so that the meter can detect it automatically. If the
Tracking Window is enabled, select Yes and press [√]. A screen similar to
the following opens. Enter the Maximum SOS and Minimum SOS.
Note: Fluid SOS, Maximum SOS and Minimum SOS are all programmed in
the same manner.
Fluid SOS Press [] again, and a screen similar to the following opens.
Fluid SOS
1496.000 m/s
Fluid SOS Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]MOVE [
]
]MODF

4.7.9 Programming the Fluid Temperature
Sensor Setup Select Fluid Temperature in the Sensor Setup menu, and press [√]. The
Traverses following screen opens.
Fluid Type
Fluid Temperature
Transducer Spacing
Fluid Temperature Press [] again, and a screen similar to the following opens.
Fluid Temperature
25.000 °C
Fluid Temperature Use the [] or [] key to select a specific digit, then use the [] or [] key
UNIT: °C to change that digit as required. After all digits are correct, press [] to
]
]UNDO [ ]SAVE
]
]MOVE [ ]MODF Note: Because the meter calculations are based on customer inputs, the
fluid temperature affects the speed of sound used during a
measurement.

4.7.10 Calculating the Path when Clamp-on selected
Sensor Setup Select Path and press [√]. The following screen opens.
Traverses
Fluid Type
Fluid Temperature
Path
Path Press [] again. Record this calculated transducer spacing for use in
Transducer Spacing installing your transducers on the pipe. The calculation is based on your
0.000 mm Sensor Setup input (pipe, transducer, fluid, and transducers).
Note: If setting the calculated spacing for your transducers is not
possible, contact the factory for assistance. Only if instructed by
the factory, press [] again, and a screen similar to the following
opens.
Transducer Spacing Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]MOVE [
]
]MODF IMPORTANT: Changing the transducer spacing should only be completed
according to instructions received from the factory.

4.7.11 Enter the Path when Wetted selected
Sensor Setup Select Path and press [√]. The following screen opens.
Traverses
Fluid Type
Fluid Temperature
Path
Path In the Sensor Setup menu, select Path Length or Axial Length and press
Path Length [√]. A screen similar to the following opens.
Axial Length
Path Press [√] again. Enter this Path use in installing your transducers on the
Path Length pipe. The calculation is based on your Sensor Setup input (pipe,
0.000 mm transducer, fluid, and traverses).
Path Length Use the [] or [] key to select a specific digit, then use the [] or [] key
]
]UNDO [ ]SAVE
]MOVE [
]
]MODF
IMPORTANT: Changing the transducer spacing should only be completed according to instructions received
from the factory.



5.1 Error Display in the User Interface
The bottom line of the LCD displays a single, top priority error message during operation. This line, called the
Error Line, includes two parts: Error header and Error String. The Error header indicates the error pattern and
error number, while the Error string gives a detailed description of the error information.
5.1.1 Error Header
Error Pattern Error Header

Flow Error En (n is error number)
Device Error Dn (n is error number)
Warning Sn (n is error number)
5.1.2 Flow Error String

Flow errors are errors that occur during a flow measurement. These errors can be caused by disturbances in
the fluid, such as excessive particles in the flow stream or extreme temperature gradients. The errors could
also be caused by an empty pipe or other such issue. Flow errors are typically not caused by a malfunction of
the flow measurement device, but by a problem with the fluid itself or with the process piping.
Option Bar Description Good Bad

Tup Displays the upstream ultrasonic signal transit time. NA NA
Tdn Displays the downstream ultrasonic signal transit time. NA NA
DeltaT Displays the transit time difference between the upstream and NA NA
downstream signals.
Up Signal Displays the signal quality for the upstream transducer ≥1200 <400
Quality
Dn Signal Displays the signal quality for the downstream transducer ≥1200 <400
Quality
Up Amp Disc Displays the value for the signal amplitude of the upstream 24±5 <19 or >29
transducer.
Dn Amp Disc Displays the value for the signal amplitude of the downstream 24±5 <19 or >29
transducer.
SNR Up Display the value for the signal-to-noise of the upstream signal ≥4 <4
SNR Dn Display the value for the signal-to-noise of the downstream signal ≥4 <4
Gain Up Display the value for the gain of the upstream transducer 9-85 <9 or >85
Gain Dn Display the value for the gain of the downstream transducer 9-85 <9 or >85
Up Peak Displays the first value in the upstream correlation signal, which is NA NA
more than the positive threshold or is less than the negative
threshold.
Dn Peak Displays the first value in the downstream correlation signal, which is NA NA
more than the positive threshold or is less than the negative
threshold.

PeakPctUp Displays the percentage of peak of the upstream signal NA NA

PeakPctDn Displays the percentage of peak of the downstream signal NA NA
5.1.2.1 E1: Low Signal

Problem: Poor ultrasonic signal strength or the signal exceeds the programmed limit.
Cause: When the SNR is less that the value of Signal Low Limit or the signal cannot be found when the
flow is started, the Low Signal error is displayed. Poor signal strength may be caused by a
defective cable, a flowcell problem, a defective transducer or a problem in the electronics console.
A signal that exceeds the programmed limits is probably caused by the entry of an improper
value in the menu Program > Advanced > Error Limits > Signal Low limits.
Action: Refer to “Diagnostics” on page 93. Also, check the programmed value in the Program > Advanced >
Error Limits> Signal Low Limit menu.
5.1.2.2 E2: Sound Speed Error

Problem: The sound speed exceeds the limit programmed in the Program > Advanced > Error Limits>
SNSD+- Limit menu
Cause: When the measured sound speed exceeds the programmed sound speed limit, this error is
displayed. The error may result from incorrect programming, poor flow conditions, and/or poor
transducer orientation.
Action: Correct the programming errors. Refer to “Diagnostics” on page 93, to correct the flowcell and/or
transducer problems. Also, check the value programmed in the Program > Advanced > Error Limits
> SNSD +- Limit menu.
5.1.2.3 E3: Velocity Range

Problem: The velocity exceeds the limits programmed in the Program > Advanced > Error Limits
> Velocity Low/High menu.
Cause: When the measured velocity exceeds the programmed velocity limit, this error is displayed. The
error may be caused by improper programming, poor flow conditions, and/or excessive flow
turbulence.
Action: Make sure the actual flow rate is within the programmed limits. Also, check the value
programmed in the Program > Advanced > Error Limits > Velocity Low/High menu. Refer to
“Diagnostics” on page 93, to correct the flowcell and/or transducer problems.
5.1.2.4 E4: Signal Quality

Problem: The signal quality is outside the limits programmed in the Program > Advanced > Error Limits
> Correlation Peak menu.
Cause: The peak of the upstream or downstream correlation signals has fallen below the correlation
peak limit programmed in the Program > Advanced > Error Limits > Correlation Peak menu. This may
be caused by a flowcell or electrical problem.

Action: Check for sources of electrical interference and verify the integrity of the electronics console by
temporarily substituting a test flowcell that is known to be good. Check the transducers and
relocate them, if necessary. See “Diagnostics” on page 93, for instructions.

5.1.2.5 E5: Amplitude Error

Problem: The signal amplitude exceeds the limits programmed in the Program > Advanced > Error Limits
> Amp Disc Min/Max menu.
Cause: Solid or liquid particulates may be present in the flowcell. Also, poor coupling for the clamp-on
transducers can cause this problem.
Action: Refer to “Diagnostics” on page 93, to correct any flowcell problems.
5.1.2.6 E6: Cycle Skip

Problem: The fluid acceleration exceeds the limits programmed in the Program > Advanced > Error Limits
> Acceleration menu.
Cause: This condition is usually caused by poor flow conditions or improper transducer alignment.
Action: Refer to “Diagnostics” on page 93, to correct any flowcell and/or transducer problems.

5.2 Diagnostics
5.2.1 Introduction
This section explains how to troubleshoot the AT600 if problems arise with the electronics enclosure, the
flowcell, or the transducers. Indications of a possible problem include:
• Display of an error message on the LCD display screen, Vitality PC software, or HART.
• Erratic flow readings
• Readings of doubtful accuracy (i.e., readings that are not consistent with readings from another flow
measuring device connected to the same process).
If any of the above conditions occurs, proceed with the instructions presented in this section.
5.2.2 Flowcell Problems

If preliminary troubleshooting of an Error Code display indicates a possible flowcell problem, proceed with
this section. Flowcell problems fall into two categories: fluid problems or pipe problems. Read the following
sections carefully to determine if the problem is indeed related to the flowcell. If the instructions in this
section fail to resolve the problem, contact GE for assistance.
5.2.2.1 Fluid Problems

Most fluid-related problems result from a failure to observe the flow meter system installation instructions.
Refer to Chapter 2, Installation, to correct any installation problems.
If the physical installation of the system meets the recommended specifications, it is possible that the fluid
itself may be preventing accurate flow rate measurements. The fluid being measured must meet the
following requirements:
• The fluid must be homogeneous, single-phase, relatively clean and flowing steadily.
Although a low level of entrained particles may have little effect on the operation of the AT600,
excessive amounts of solid or gas particles will absorb or disperse the ultrasound signals. This
interference with the ultrasound transmissions through the fluid causes inaccurate flow rate
measurements. In addition, temperature gradients in the fluid may result in erratic or inaccurate
flow rate readings.
• The fluid must not cavitate near the flowcell.
Fluids with a high vapor pressure may cavitate near or in the flowcell. This causes problems resulting
from gas bubbles in the fluid. Cavitation can usually be controlled through proper installation
procedures.
• The fluid must not excessively attenuate ultrasound signals.
Some fluids, particularly those that are very viscous, readily absorb ultrasound energy. In such cases,
an E1 error code message appears on the display screen to indicate that the ultrasonic signal strength
is insufficient for reliable measurements.

5.2.2.1 Fluid Problems (cont)

• The fluid sound speed must not vary excessively.
The AT600 will tolerate relatively large changes in the fluid sound speed, as may be caused by
variations in fluid composition and/or temperature. However, such changes must occur slowly. Rapid
fluctuations in the fluid sound speed, to a value that exceeds the limit programmed into the AT600,
will result in erratic or inaccurate flow rate readings. Refer to Chapter 3, Initial Setup and
Programming, and make sure that the appropriate sound speed limit is programmed into the meter.
5.2.2.2 Pipe Problems

Pipe-related problems may result either from a failure to observe the installation instructions, as described
in Chapter 2, Installation, or from improper programming of the meter. By far, the most common pipe
problems are the following:
• The collection of material at the transducer location(s).
Accumulated debris at the transducer location(s) will interfere with transmission of the ultrasound
signals. As a result, accurate flow rate measurements are not possible. Realignment of the flowcell or
transducers often cures such problems, and in some cases, transducers that protrude into the flow
stream may be used. Refer to Chapter 2, Installation, for more details on proper installation practices.
• Inaccurate pipe measurements.
The accuracy of the flow rate measurements is no better than the accuracy of the programmed pipe
dimensions. For a flowcell supplied by GE, the correct data will be included in the documentation.
For other flowcells, measure the pipe wall thickness and diameter with the same accuracy desired in
the flow rate readings. Also, check the pipe for dents, eccentricity, weld deformity, straightness and
other factors that may cause inaccurate readings. Refer to Chapter 3, Initial Setup, for instructions on
programming the pipe data.
In addition to the actual pipe dimensions, the path length (P) and the axial dimension (L), based on
the actual transducer mounting locations, must be accurately programmed into the flow meter. For a
GE flowcell, this data will be included with the documentation for the system. If the transducers are
mounted onto an existing pipe, these dimensions must be precisely measured.
• The inside of the pipe or flowcell must be relatively clean.
Excessive buildup of scale, rust or debris will interfere with flow rate measurement. Generally, a thin
coating or a solid well-adhered build up on the pipe wall will not cause problems. Loose scale and
thick coatings (such as tar or oil) will interfere with ultrasound transmission and may result in
incorrect or unreliable measurements.



6.1 MODBUS
6.1.1 Introduction
The AT600 flow meter generally follows the standard MODBUS communications protocol defined by the
MODBUS APPLICATION PROTOCOL SPECIFICATION V1.1b, which is available at www.modbus.org. With this
reference as a guide, an operator can use any MODBUS master to communicate with the AT600 flow meter.
For the AT600, there are two limits of this implementation:

1. The AT600 supports only four of the standard function codes. These are Read Holding Registers
(0x03), Read Input Registers (0x04), Write Multiple Registers (0x10), and Read File Record (0x14).
2. The AT600 needs a 15 ms gap between Modbus requests. The prime objective of the flow meter is to
measure flow and drive the output, so the Modbus server has a low priority.
6.1.2 MODBUS Register Map
Table 7: MODBUS Register Map

Register Register (in
(in Hex) Decimal) Access Level Description RO/RW Format
100 100 256 User Product Short Tag RW CHAR * 16
108 264 User Product Long Tag RW CHAR * 32
118 280 User Product message (for HART) RW CHAR * 32
128 296 User Product descriptor (for HART) RW CHAR * 16
140 140 320 User Product Electronic serial RW CHAR * 16
number
148 328 User Product fixture serial number RW CHAR * 16
150 336 User Product transducer1 serial RW CHAR * 16
number
158 344 User Product transducer2 serial RW CHAR * 16
number
300 300 768 RO Main Hardware version RO CHAR * 8
304 772 RO Option Hardware version RO CHAR * 8
308 776 RO Main Software version RO CHAR * 8
500 500 1280 User Global Unit group 1 for Actual RW INT32
Volumetric
502 1282 User Global Unit group 2 for Day RW INT32
504 1284 User Global Unit group 3 for dB RW INT32
506 1286 User Global Unit group 4 for Density RW INT32
508 1288 User Global Unit group 5 for RW INT32
Dimension
50A 1290 User Global Unit group 6 for Hz RW INT32
50C 1292 User Global Unit group 7 for RW INT32
Viscosity

Table 7: MODBUS Register Map (cont.)

50E 1294 User Global Unit group 8 for mA RW INT32
510 1296 User Global Unit group 9 for Mass RW INT32
512 1298 User Global Unit group 10 for Milli RW INT32
Second
514 1300 User Global Unit group 11 for Nano RW INT32
Second
Percent
518 1304 User Global Unit group 13 for Second RW INT32
51A 1306 User Global Unit group 14 for RW INT32
Standard Volumetric
51C 1308 User Global Unit group 15 for RW INT32
Thermo
51E 1310 Viewer Global Unit group 16 for RW INT32
Totalizer time
Totalizer
Unitless
524 1316 User Global Unit group 19 for Micro RW INT32
Second
Velocity
Acceleration
540 540 1344 Viewer Batch request command RW INT32
542 1346 User inventory request command RW INT32
544 1348 Viewer system request password RW INT32
546 1350 Viewer system request command RW INT32
700 700 1792 RO System Reported error RO INT32
702 1794 RO System Error Bitmap RO INT32
704 1796 RO System Startup error Bitmap RO INT32
706 1798 RO System Flow error Bitmap RO INT32
708 1800 RO System Device error Bitmap RO INT32
70A 1802 RO System Warning Bitmap RO INT32
740 740 1856 RO System Protocol type RO INT32
900 900 2304 Viewer Display Language RW INT32
902 2306 User Display Backlight Enable RW INT32
904 2308 User Display Timeout RW INT32
906 2310 Viewer Display Type RW INT32
908 2312 Viewer Display Variable1 Type RW INT32


90A 2314 Viewer Display Variable2 Type RW INT32
90C 2316 Viewer Display Totalizer1 Type RW INT32
90E 2318 Viewer Display Totalizer2 Type RW INT32
910 2320 Viewer Display Decimal selection RW INT32
940 940 2368 User select the velocity RW INT32
942 2370 User select the Actual Volumetric RW INT32
944 2372 User select the Standardized RW INT32
Volumetric
946 2374 User select Mass RW INT32
948 2376 User select Totalizer RW INT32
A00 A00 2560 RO Display Variable1 Value RO (IEEE 32 bit)
A02 2562 RO Display Variable2 Value RO (IEEE 32 bit)
A04 2564 RO Display Totalizer1 Value RO (IEEE 32 bit)
A06 2566 RO Display Totalizer2 Value RO (IEEE 32 bit)
C00 C00 3072 User Analog Out Error Handling RW (IEEE 32 bit)
Value
C02 3074 User Analog Out Test Value (Percent RW (IEEE 32 bit)
of Span)
C04 3076 User Analog Out Zero Value RW (IEEE 32 bit)
C06 3078 User Analog Out Span Value RW (IEEE 32 bit)
C08 3080 User Analog Out Base Value RW (IEEE 32 bit)
C0A 3082 User Analog Out Full Value RW (IEEE 32 bit)
C40 C40 3136 User Digital Out 1 Pulse Value RW (IEEE 32 bit)
C42 3138 User Digital Out 1 Frequency Base RW (IEEE 32 bit)
Value
C44 3140 User Digital Out 1 Frequency Full RW (IEEE 32 bit)
Value
C46 3142 User Digital Out 1 Alarm Value RW (IEEE 32 bit)
C80 C80 3200 User Digital Out 2 Pulse Value RW (IEEE 32 bit)
C82 3202 User Digital Out 2 Frequency Base RW (IEEE 32 bit)
Value
C84 3204 User Digital Out 2 Frequency Full RW (IEEE 32 bit)
Value
C86 3206 User Digital Out 2 Alarm Value RW (IEEE 32 bit)
D00 D00 3328 User Analog Out Mode RW INT32
D02 3330 User Analog Out Type RW INT32
D04 3332 User Digital Out 1 Mode RW INT32
D06 3334 User Digital Out 1 Type RW INT32
D08 3336 User Digital Out 2 Mode RW INT32
D0A 3338 User Digital Out 2 Type RW INT32


D20 D20 3360 User Analog Out Measurement Type RW INT32
D22 3362 User Analog Out Error Handling RW INT32
D40 D40 3392 User Digital Out 1 Pulse RW INT32
Measurement Type
D42 3394 User Digital Out 1 Pulse Test Value RW INT32
D44 3396 User Digital Out 1 Pulse Error RW INT32
Handling
D46 3398 User Digital Out 1 Pulse Time RW INT32
D50 D50 3408 User Digital Out 2 Pulse RW INT32
Measurement Type
D52 3410 User Digital Out 2 Pulse Test Value RW INT32
D54 3412 User Digital Out 2 Pulse Error RW INT32
Handling
D56 3414 User Digital Out 2 Pulse Time RW INT32
D60 D60 3424 User Digital Out 1 Frequency RW INT32
Measurement Type
D62 3426 User Digital Out 1 Test Frequency RW INT32
Value
D64 3428 User Digital Out 1 Frequency Error RW INT32
Handling
Handling Value
D68 3432 User Digital Out 1 Frequency Full RW INT32
Frequency
D70 D70 3440 User Digital Out 2 Frequency RW INT32
Measurement Type
D72 3442 User Digital Out 2 Test Frequency RW INT32
Value
Handling
Handling Value
D78 3448 User Digital Out 2 Frequency Full RW INT32
Frequency
D80 D80 3456 User Digital Out 1 Alarm RW INT32
Measurement Type
D82 3458 User Digital Out 1 Alarm Test Value RW INT32
D84 3460 User Digital Out 1 Alarm State RW INT32
D86 3462 User Digital Out 1 Alarm Type RW INT32
D90 D90 3472 User Digital Out 2 Alarm RW INT32
Measurement Type
D92 3474 User Digital Out 2 Alarm Test Value RW INT32
D94 3476 User Digital Out 2 Alarm State RW INT32


D96 3478 User Digital Out 2 Alarm Type RW INT32
E00 E00 3584 RO Analog Out Measurement Value RO (IEEE 32 bit)
E02 3586 RO Digital Out 1 Pulse RO (IEEE 32 bit)
Measurement Value
E04 3588 RO Digital Out 1 Frequency RO (IEEE 32 bit)
Measurement Value
E06 3590 RO Digital Out 1 Alarm RO (IEEE 32 bit)
Measurement Value
E08 3592 RO Digital Out 2 Pulse RO (IEEE 32 bit)
Measurement Value
E0A 3594 RO Digital Out 2 Frequency RO (IEEE 32 bit)
Measurement Value
E0C 3596 RO Digital Out 2 Alarm RO (IEEE 32 bit)
Measurement Value
1100 1100 4352 Viewer HART meter address RW INT32
1102 4354 Viewer HART preamble length RW INT32
1104 4356 Viewer HART device ID RW INT32
1106 4358 Viewer HART assembly number RW INT32
1140 1140 4416 Viewer HART Dynamic Variable Index RW INT32
_1
1142 4418 Viewer HART Dynamic Variable Index RW INT32
_2
_3
_4
1300 1300 4864 RO HART Configuration Change RO INT32
Count
1302 4866 RO HART Device Status RO INT32
1304 4868 RO HART Device Status Extended RO INT32
1306 4870 RO HART master status RO INT32
1308 4872 RO HART secondary status RO INT32
130A 4874 RO HART variable status RO INT32
1500 1500 5376 User PC MODBUS baud rate RW INT32
1502 5378 User PC MODBUS parity RW INT32
1504 5380 User PC MODBUS stop bits RW INT32
1506 5382 User PC MODBUS meter address RW INT32
1540 1540 5440 User Log control / status RW INT32
1542 5442 User Log interval RW INT32
1544 5444 User Logging time RW INT32
1546 5446 User Number of variables to log RW INT32


1580 1580 5504 User variable address array RW INT32
15C0 15C0 5568 User Variable unit code array RW INT32
1700 1700 5888 RO PC Service baud rate RO INT32
1702 5890 RO PC Service parity RO INT32
1704 5892 RO PC Service stop bits RO INT32
1706 5894 RO PC Service meter address RO INT32
1740 1740 5952 RO Number of records RO INT32
2000 2000 8192 User Pipe Inner Diameter RW (IEEE 32 bit)
2002 8194 User Pipe Outer Diameter RW (IEEE 32 bit)
2004 8196 User Pipe Wall Thickness RW (IEEE 32 bit)
2006 8198 User Pipe Soundspeed RW (IEEE 32 bit)
2008 8200 User Lining Thickness RW (IEEE 32 bit)
200A 8202 User Lining Soundspeed RW (IEEE 32 bit)
200C 8204 User XDR wedge angle RW (IEEE 32 bit)
200E 8206 User XDR wedge time RW (IEEE 32 bit)
2010 8208 User Wedge Sound speed RW (IEEE 32 bit)
2012 8210 User Fluid Sound speed RW (IEEE 32 bit)
2014 8212 User Fluid Sound speed Min RW (IEEE 32 bit)
2016 8214 User Fluid Sound speed Max RW (IEEE 32 bit)
2018 8216 User Fluid Static Density RW (IEEE 32 bit)
201A 8218 User Fluid Reference Density RW (IEEE 32 bit)
201C 8220 User Fluid Temperature RW (IEEE 32 bit)
201E 8222 User XDR space RW (IEEE 32 bit)
2020 8224 User Calibration Factor RW (IEEE 32 bit)
2022 8226 User Kinematic Viscosity RW (IEEE 32 bit)
2040 2040 8256 User MultiK Velocity 1 RW (IEEE 32 bit)
2042 8258 User MultiK Velocity 2 RW (IEEE 32 bit)
204A 8266 User MultiK Velocity 6 RW (IEEE 32 bit)
2060 2060 8288 User MultiK Velocity KFactor1 RW (IEEE 32 bit)
2062 8290 User MultiK Velocity KFactor2 RW (IEEE 32 bit)
206A 8298 User MultiK Velocity KFactor6 RW (IEEE 32 bit)
2080 2080 8320 User MultiK Reynolds 1 RW (IEEE 32 bit)


2082 8322 User MultiK Reynolds 2 RW (IEEE 32 bit)
208A 8330 User MultiK Reynolds 6 RW (IEEE 32 bit)
20A0 20A0 8352 User MultiK Reynolds KFactor1 RW (IEEE 32 bit)
20A2 8354 User MultiK Reynolds KFactor2 RW (IEEE 32 bit)
20AA 8362 User MultiK Reynolds KFactor6 RW (IEEE 32 bit)
20C0 20C0 8384 User Correlation peak low limit RW (IEEE 32 bit)
20C2 8386 User Acceleration Limit RW (IEEE 32 bit)
20C4 8388 User Velocity Low limit - Used for RW (IEEE 32 bit)
Volumetric low limit
calculation
20C6 User Velocity High limit - Used for RW (IEEE 32 bit)
Volumetric High limit
calculation
20C8 8392 User Amplitude discriminator min RW (IEEE 32 bit)
limit
20CA 8394 User Amplitude discriminator max RW (IEEE 32 bit)
limit
20CC 8396 User Soundspeed Plus minus limit RW (IEEE 32 bit)
20CE 8398 User signal low limit RW (IEEE 32 bit)
20E0 20E0 8416 User Zero Cutoff RW (IEEE 32 bit)
20E2 8418 User DeltaT Offset RW (IEEE 32 bit)
2100 2100 8448 User Pipe Material RW INT32
2102 8450 User Lining Material RW INT32
2104 8452 User XDR Type RW INT32
2106 8454 User XDR frequency RW INT32
2108 8456 User XDR wedge type RW INT32
210A 8458 User Fluid Type RW INT32
210C 8460 User Lining existence RW INT32
210E 8462 User Traverse number RW INT32
2140 2140 8512 User Enable Reynolds Correction RW INT32
2142 8514 User Enable Active MultiK RW INT32
2144 8516 User MultiK Type RW INT32
2146 8518 User MultiK Pairs RW INT32
2180 2180 8576 User Peak% RW INT32


2182 8578 User Min Peak% RW INT32
2184 8580 User Max Peak% RW INT32
2186 8582 User Errors Allowed RW INT32
21C0 21C0 8640 User Enable Active TW RW INT32
21C2 8642 User Enable Tracking Windows RW INT32
21C4 8644 User Response Time RW INT32
21C6 8646 User Sample Size RW INT32
2200 2200 8704 RO Velocity RO (IEEE 32 bit)
2202 8706 RO Volumetric RO (IEEE 32 bit)
2204 8708 RO Standard Volumetric RO (IEEE 32 bit)
2206 8710 RO Mass Flow RO (IEEE 32 bit)
2240 2240 8768 RO Batch Fwd totals RO (IEEE 32 bit)
2242 8770 RO Batch rev totals RO (IEEE 32 bit)
2244 8772 RO Batch net totals RO (IEEE 32 bit)
2246 8774 RO Batch totals time RO (IEEE 32 bit)
2248 8776 RO Inventory Fwd totals RO (IEEE 32 bit)
224A 8778 RO inventory rev totals RO (IEEE 32 bit)
224C 8780 RO inventory net totals RO (IEEE 32 bit)
224E 8782 RO inventory totals time RO (IEEE 32 bit)
2280 2280 8832 RO Transit Time Up RO (IEEE 32 bit)
2282 8834 RO Transit Time Dn RO (IEEE 32 bit)
2284 8836 RO DeltaT RO (IEEE 32 bit)
2286 8838 RO Up Signal Quality RO (IEEE 32 bit)
2288 8840 RO Dn Signal Quality RO (IEEE 32 bit)
228A 8842 RO Up Amp Disc RO (IEEE 32 bit)
228C 8844 RO Dn Amp Disc RO (IEEE 32 bit)
228E 8846 RO SNR on UP channel RO (IEEE 32 bit)
2290 8848 RO SNR on DOWN channel RO (IEEE 32 bit)
2292 8850 RO Time in buffer on Up channel RO (IEEE 32 bit)
2294 8852 RO Time in buffer on Dn channel RO (IEEE 32 bit)
2296 8854 RO Signal Gain Up RO (IEEE 32 bit)
2298 8856 RO Signal Gain Down RO (IEEE 32 bit)
22C0 22C0 8896 RO Sound Speed RO (IEEE 32 bit)
22C2 8898 RO Current Reynolds Number RO (IEEE 32 bit)
22C4 8900 RO Current Correction Factor RO (IEEE 32 bit)
22C6 8902 RO Path Length P RO (IEEE 32 bit)
22C8 8904 RO Axial Length L RO (IEEE 32 bit)
2300 2300 8960 RO Up +- Peak RO INT32


2302 8962 RO Dn +- Peak RO INT32
2304 8964 RO dynamic threshold on UP RO INT32
channel
2306 8966 RO dynamic threshold on DOWN RO INT32
channel
6.2 HART
6.2.1 Device Identification
The AT600 flow meter supports the HART communication protocol, for which the manufacturer ID is 0x9D
(157 Dec) and the Device type Code is 0x9D73 (127 Dec).
6.2.2 Commands
6.2.2.1 Universal Commands
Table 8: Universal Commands for HART
Command Function Description
0 Read Unique Identifier Returns identity information about the meter including: the Device Type,
revision levels, and Device ID.
1 Read Primary Variable Returns the Primary Variable value along with its Unit Code
2 Read Loop Current And Reads the Loop Current and its associated Percent of Range.
Percent Of Range
3 Read Dynamic Variables and Reads the Loop Current and up to four predefined Dynamic Variables. The
Loop Current Dynamic Variables and associated units are defined via Commands 51
and 53.
6 Write Polling Address Writes the polling address and the loop current mode to the field device.
7 Read Loop Configuration Read polling address and the loop current mode.
8 Read Dynamic Variable Reads the Classification associated with the Dynamic variable.
Classification
9 Read Device Variables with Request the value and status of up to eight device Device or Dynamic
Status Variables.
11 Read Unique Identifier If the specified tag matches that of the meter, it responds with the
Associated With Tag Command 0 response.
12 Read Message Reads the Message contained within the meter.
13 Read Tag, Descriptor, Date Reads the Tag, Descriptor, and Date contained within the meter.
14 Read Primary Variable Reads the Transducer (meter) Serial Number, Limits/Minimum Span Units
Transducer Information Code, Upper Transducer Limit, Lower Transducer Limit, and Minimum
Span for the Primary Variable transducer.
15 Read Device Information Reads the alarm selection code, transfer function code, range values units
code upper range value, Primary Variable lower range value, damping
value, write protect code, and private label distributor code.
16 Read Final Assembly Reads the Final Assembly Number associated with the meter.
Number
17 Write Message Write the Message into the meter.
18 Write Tag, Descriptor, Date Write the Tag, Descriptor, and Date Code into the meter.

Table 8: Universal Commands for HART (cont.)

Command Function Description
19 Write Final Assembly Write the Final Assembly Number into the meter.
Number
20 Read Long Tag Read the 32-byte Long Tag.
21 Read Unique Identifier Read Unique Identifier Associated with Long Tag
Associated with Long Tag
22 Write Long Tag Write the 32-byte Long Tag
38 Reset Configuration Resets the configuration changed indicator (Device Status Byte bit 6).
Changed Flag
48 Read Additional Device Returns meter status information not included in the Response Code or
Status Device Status Byte.
6.2.2.2 Common Commands
Table 9: Common Commands

Comman Function Description
d
33 Read Device Variables Allows a Master to request the value of up to four Device Variables.
50 Read Dynamic Variable Reads the Device Variables assigned to the Primary, Secondary, Tertiary,
Assignments and Quaternary Variables.
51 Write Dynamic Variable Allows the user to assign Device Variables to the Primary, Secondary,
Assignments Tertiary, and Quaternary Variables
54 Read Device Variable Get device variable information
Information
59 Write Number of Response Sets the number of asynchronous preamble bytes to be sent by the meter
Preambles before the start of a response message.
6.2.2.3 Device Specific Commands

The AT600 flow meter supports a variety of device-specific commands in which the parameter may be the
measurement type. The available measurement types are listed in Table 10 below.
Table 10: Available Measurement Types

Index Meaning
1 Velocity
2 Volumetric
3 Standard Volumetric
4 Mass Flow
5 Batch Fwd. Totalizer
6 Batch Rev. Totalizer
7 Batch Net Totalizer
8 Batch Totalizer Time
9 Inventory Fwd. Totalizer
10 Inventory Rev. Totalizer

Table 10: Available Measurement Types (cont.)

11 Inventory Net Totalizer
12 Inventory Totalizer Time
13 Sound Speed
14 Reynolds Kfactor
15 MultiK Kfactor
16 Transit Time Up
17 Transit Time Down
18 Deltat
19 Signal Quality Up
20 Signal Quality Down
21 Amp Disc Up
22 Amp Disc Down
23 SNR Up
24 SNR Down
25 ActiveTW Up
26 ActiveTW Down
27 Gain Up
28 Gain Down
29 System Error Bitmap
30 System Report Error Number
31 Peak Up
32 Peak Down
33 Peak Pct. Up
34 Peak Pct. Down
Command 128 (0x80): Login with Password

This command sends a password to the flow meter. If the password is correct, the user may operate the
meter until there has been a gap of 10 minutes since the last command.
Table 11: Request Data Bytes for Login with Password

Byte Format Description
0-3 Unsigned-32 User password
Table 12: Response Data Bytes for Login with Password

None

Table 13: Command-Specific Response Codes for Login with Password

Code Class Description
0 Success No Command-Specific Errors
1-4 Undefined
5 Error Too Few Data Bytes Received
6 Error Device-Specific Command Error
7-15 Undefined
16 Error Access Restricted
17-127 Undefined

Command 129 (0x81): Logout and Save

This command will save any changes and logout from the flow meter.
Table 14: Request Data Bytes for Logout and Save

None
Table 15: Response Data Bytes for Logout and Save

None
Command 129 (0x81): Logout and Save (cont.)

Table 16: Command-Specific Response Codes for Logout and Save
1-5 Undefined
7 Error In Write Protect Mode
8-15 Undefined
17-127 Undefined
Command 130 (0x82): Logout without Saving

This command will logout the flow meter and not save anything.
Table 17: Request Data Bytes for Logout without Saving

None
Table 18: Response Data Bytes for Logout without Saving

None
Table 19: Command-Specific Response Codes for Logout without Saving

1-5 Undefined
7-15 Undefined
17-127 Undefined

Command 135 (0x87): Read Current User Access Right

This command will read the current user access right.
Table 20: Request Data Bytes for Read Current User Access Right
None
Table 21: Response Data Bytes for Read Current User Access Right
None
Table 22: Command-Specific Response Codes for Read Current User Access Right
1-127 Undefined
Command 136 (0x88): Sends New Password

This command will send a new password to the flow meter. If the user has the right, the flow meter changes
the user password.
Table 23: Request Data Bytes for Sends New Password

0-3 Unsigned-32 User password
Table 24: Response Data Bytes for Sends New Password

None

Command 136 (0x88): Sends new password (cont.)
Table 25: Command-Specific Response Codes for Sends New Password

1-4 Undefined
8-15 Undefined
17-127 Undefined
Command 144 (0x90): Read Unit Group

This command will read the unit group in the meter.
Table 26: Request Data Bytes for Read Unit Group

0 Unsigned-8 Group index:
1: Velocity unit;
2: Actual Volumetric unit;
3: Standard Volumetric unit;
4: Mass unit;
5: Totalizer unit;
6: Density unit;
7: Pipe Dimension;
8: Thermal;
9: Acceleration;

Command 144 (0x90): Read Unit Group (cont.)
Table 27: Response Data Bytes for Read Unit Group

1: Velocity unit;
4: Mass unit;
5: Totalizer unit;
6: Density unit;
7: Pipe Dimension;
8: Thermal;
9: Acceleration;
1 Enum unit code
Table 28: Command-Specific Response Codes for Read Unit Group

1 Undefined
2 Error Invalid Selection
3-4 Undefined
7-127 Undefined
Command 145 (0x91): Read Density Value

This command will read density value in meter.
Table 29: Request Data Bytes for Read Density Value

0 Unsigned-8 Density type:
1: Actual Density;
2: Reference Density;

Command 145 (0x91): Read Density Value (cont.)
Table 30: Response Data Bytes for Read Density Value

1: Actual Density;
1 Unsigned-8 Density Unit Code
2-5 Float Density value
Table 31: Command-Specific Response Codes for Read Density Value

1 Undefined
3-4 Undefined
7-127 Undefined
Command 146 (0x92): Read Backlight Setting

This command is to read the backlight setting.
Table 32: Request Data Bytes for Read Backlight Setting

None
Table 33: Response Data Bytes for Read Backlight Setting

0 Unsigned-8 Backlight control switch (0:off/ 1:on)
1-4 Unsigned-32 Display backlight timeout, unit is second.

Command 146 (0x92): Read Backlight Setting (cont.)
Table 34: Command-Specific Response Codes for Read Backlight Setting

1-5 Undefined
7-127 Undefined
Command 152 (0x98): Write Unit Group

This command will write unit group in meter.
Table 35: Request Data Bytes for Write Unit Group

1: Velocity unit;
4: Mass unit;
5: Totalizer unit;
6: Density unit;
7: Pipe Dimension;
8: Thermal;
9: Acceleration;
1 Enum unit code

Command 152 (0x98): Write Unit Group (cont.)
Table 36: Response Data Bytes for Write Unit Group

1: Velocity unit;
4: Mass unit;
5: Totalizer unit;
6: Density unit;
7: Pipe Dimension;
8: Thermal;
9: Acceleration;
1 Enum unit code
Table 37: Command-Specific Response Codes for Write Unit Group

1 Undefined
3-4 Undefined
8 - 15 Undefined
17 - 127 Undefined

Command 153 (0x99): Write Density Value

This command will write density value in meter.
Table 38: Request Data Bytes for Write Density Value

1: Actual Density;
Table 39: Response Data Bytes for Write Density Value

1: Actual Density;
Table 40: Command-Specific Response Codes for Write Density Value

1 Undefined
3-4 Undefined
8 - 15 Undefined
17 - 127 Undefined

Command 154 (0x9A): Write Display Backlight

This command is to set the back light.
Table 41: Request Data Bytes for Write Display Backlight

Table 42: Response Data Bytes for Write Display Backlight

Table 43: Command-Specific Response Codes for Write Display Backlight

1-4 Undefined
8-15 Undefined
17-127 Undefined
Command 160 (0xA0): Read Analog Measurement Range Values

This command is to read the Analog Measurement range.
Table 44: Request Data Bytes for Read Analog Measurement Range Values
None
Table 45: Response Data Bytes for Read Analog Measurement Range Value
0 Unsigned-8 Upper and Lower Range Values Unit Code
1-4 Float Upper Range Value
5-8 Float Lower Range Value

Command 160 (0xA0): Read Analog Measurement Range Values (cont.)
Table 46: Command-Specific Response Codes for Read Analog Measurement Range Value
1-5 Undefined
7 - 127 Undefined
Command 161 (0xA1): Read Loop Current Error Handling

This command is to read the loop current output error handling.
Table 47: Request Data Bytes for Read Loop Current Error Handling
None
Table 48: Response Data Bytes for Read Loop Current Error Handling
0 Unsigned-8 Analog Output Error Handling:
0: Low;
1: High;
2: Hold;
3: Other value;
1-4 Float Error Value, unit is mA
Table 49: Command-Specific Response Codes for Read Loop Current Error Handling
1-5 Undefined
7 - 127 Undefined

Command 168 (0xA8): Enter / Exit Fixed Loop Current

Enter or exit the fixed mode of loop current.
Table 50: Request Data Bytes for Enter / Exit Fixed Loop Current
0 Unsigned-8 Fixed current level:
0: Exit Fixed Loop Current; 1: Fixed 4 mA; 2: Fixed 20mA; 3: Fixed
Percentage of Scale
Table 51: Response Data Bytes for Enter / Exit Fixed Loop Current
0 Unsigned-8 Fixed current level:
0: Exit Fixed Loop Current; 1: Fixed 4 mA; 2: Fixed 20mA; 3: Fixed
Percentage of Scale
Table 52: Command-Specific Response Code for Enter / Exit Fixed Loop Currents
1-4 Undefined
8 - 10 Undefined
11 Error Loop Current Not Active
12 - 15 Undefined
17-31 Undefined
32 Error Busy
33 - 127 Undefined

Command 169 (0xA9): Set Loop Current Zero

This command is to trim the zero or lower endpoint value of the loop current to its minimum.
Table 53: Request Data Bytes for Set Loop Current Zero
0-3 Float Externally Measured Loop Current Level, units of milliamperes
Table 54: Response Data Bytes for Set Loop Current Zero
Table 55: Command-Specific Response Codes for Set Loop Current Zero
1-2 Undefined
3 Error Passed Parameter Too Large
4 Error Passed Parameter Too Small
8 Undefined
9 Error Incorrect Loop Current Mode or Value
10 - 15 Undefined
17-31 Undefined
32 Error Busy
33 - 127 Undefined

Command 170 (0xAA): Set Loop Current Gain

This command is to trim the gain or upper endpoint value of the loop current to its maximum.
Table 56: Request Data Bytes for Set Loop Current Gain
Table 57: Response Data Bytes for Set Loop Current Gain
Table 58: Command-Specific Response Codes for Set Loop Current Gain
1-2 Undefined
8 Undefined
10 - 15 Undefined
17 - 31 Undefined
32 Error Busy
33 - 127 Undefined

Command 171 (0xAB): Set Loop Current Percentage

This command is to set the output percentage of loop current.
Table 59: Request Data Bytes for Set Loop Current Percentage
0-3 Float Loop Current Percentage, units of percent.
Table 60: Response Data Bytes for Set Loop Current Percentage
0-3 Float Loop Current Percentage, units of percent.
Table 61: Command-Specific Response Codes for Set Loop Current Percentage
1-2 Undefined
8 Undefined
10 - 15 Undefined
17-31 Undefined
32 Error Busy
33 - 127 Undefined

Command 172 (0xAC): Set Analog Measurement Range Values

This command is to set the Analog Measurement range.
Table 62: Request Data Bytes for Set Analog Measurement Range Values
Table 63: Response Data Bytes for Set Analog Measurement Range Values
Table 64: Command-Specific Response Codes for Set Analog Measurement Range Values
1-4 Undefined
8 Warning Set To Nearest Possible Value (Upper or Lower Range Pushed)
9 Error Lower Range Value Too High
10 Error Lower Range Value Too Low
11 Error Upper Range Value Too High
12 Error Upper Range Value Too Low
13 - 15 Undefined
17 Undefined
18 Error Invalid Units Code
19 - 31 Undefined
32 Error Busy
33 - 127 Undefined

Command 173 (0xAD): Set Loop Current Error Handling

This command will set the loop current output error handling.
Table 65: Request Data Bytes for Set Loop Current Error Handling
0: Low;
1: High;
2: Hold;
3: Other value;
Table 66: Response Data Bytes for Set Loop Current Error Handling
0: Low;
1: High;
2: Hold;
3: Other value;
Table 67: Command-Specific Response Codes for Set Loop Current Error Handling
1-4 Undefined
8-15 Undefined
17-127 Undefined

Command 176 (0xB0): Read Digital Configuration

This command is to read the digital output configuration.
Table 68: Request Data Bytes

None Unsigned-8 Channel Number (1/2)
Table 69: Response Data Bytes

0 Unsigned-8 Channel Number
1 Unsigned-8 Digital Output type:
0: Off; 1: Pulse; 2: Frequency; 3: Alarm;
Table 70: Command-Specific Response Codes

1 Undefined
3-4 Undefined
7-127 Undefined

Command 177 (0xB1): Read Pulse Configuration

This command is to read the pulse configuration.
Table 71: Request Data Bytes for Read Pulse Configuration

0 Unsigned-8 Channel Number (1/2)
Table 72: Response Data Bytes for Read Pulse Configuration

1 Unsigned-8 Measurement Type:
5: Forward Batch Total;
6: Reverse Batch Total;
7: Net Batch Total;
2 Unsigned-8 Pulse Value Unit
3-6 Float Pulse Value
7 - 10 Unsigned-32 Pulse Time, Unit is MS
11 Unsigned-8 Pulse Error Handling:
2: Hold Good Value;
4: Stop;
Table 73: Command-Specific Response Codes for Read Pulse Configuration

1 Undefined
3-4 Undefined
7-127 Undefined

Command 178 (0xB2): Read Frequency Configuration

This command is to read the frequency configuration.
Table 74: Request Data Bytes for Read Frequency Configuration

Table 75: Response Data Bytes for Read Frequency Configuration

1 Unsigned-8 Measurement Type
2 Unsigned-8 Frequency Value Unit
3-6 Float Frequency Base Value
7 - 10 Float Frequency Full Value
11 - 14 Unsigned-32 Full Frequency, unit is Hz
15 Unsigned-8 Frequency Error Handling:
0: Low;
1: High;
2: Hold;
3: Value
16 - 19 Unsigned-32 Error Handling value, unit is Hz
Table 76: Command-Specific Response Codes for Read Frequency Configuration

1 Undefined
3-4 Undefined
7-127 Undefined

Command 179 (0xB3): Read Alarm Configuration

This command is to read the alarm configuration.
Table 77: Request Data Bytes for Read Alarm Configuration

Table 78: Response Data Bytes for Read Alarm Configuration

2 Unsigned-8 Alarm Value Unit
3-6 Float Alarm Value
7 Unsigned-8 Alarm Type: 0: Low; 1: High; 2: Fault
8 Unsigned-8 Alarm State: 0: Normally; 1: Failsafe;
Table 79: Command-Specific Response Codes for Read Alarm Configuration

1 Undefined
3-4 Undefined
7-127 Undefined

Command 184 (0xB8): Write Digital Configuration

This command is to write the digital output configuration.
Table 80: Request Data Bytes for Write Digital Configuration

0 Unsigned-8 Channel Number(1/2)
Table 81: Response Data Bytes for Write Digital Configuration

Table 82: Command-Specific Response Codes for Write Digital Configuration

1 Undefined
3-4 Undefined
8-15 Undefined
8-127 Undefined

Command 185 (0xB9): Write Pulse Configuration

This command is to write the pulse configuration.
Table 83: Request Data Bytes for Write Pulse Configuration

7: Net Batch Total;
7 - 10 Unsigned-32 Pulse Time, Unit is ms
2: Hold Good Value;
4: Stop;
Table 84: Response Data Bytes for Write Pulse Configuration

7: Net Batch Total;
7 - 10 Float Pulse Time, Unit is ms
0: Hold Good Value;
1: Stop;

Command 185 (0xB9): Write Pulse Configuration (cont.)
Table 85: Command-Specific Response Codes for Write Pulse Configuration

1 Undefined
3-4 Undefined
8-15 Undefined
8-127 Undefined
Command 186 (0xBA): Write Frequency Configuration

This command is to write the frequency configuration.
Table 86: Request Data Bytes for Write Frequency Configuration

11 - 14 Unsigned-32 Full Frequency, unit is Hz
0: Low;
1: High;
2: Hold;
3: Value

Command 186 (0xBA): Write Frequency Configuration (cont.)
Table 87: Response Data Bytes for Write Frequency Configuration

11 - 14 Float Full Frequency, unit is Hz
0: Low;
1: High;
2: Hold;
3: Value
Table 88: Command-Specific Response Codes for Write Frequency Configuration

1 Undefined
3-4 Undefined
8-15 Undefined
8-127 Undefined

Command 187 (0xBB): Write Alarm Configuration

This command is to write the alarm configuration.
Table 89: Request Data Bytes for Write Alarm Configuration

Table 90: Response Data Bytes for Write Alarm Configurations

Table 91: Command-Specific Response Codes for Write Alarm Configuration

1 Undefined
3-4 Undefined
8-15 Undefined
8-127 Undefined

Command 191 (0xBF): Test Digital Output

This command is to test the digital output
Table 92: Request Data Bytes for Test Digital Output

1 Unsigned-8 Test DO Type
Test Stop
Pulse
Frequency
Alarm
2-5 Unsigned-32 Test value
Table 93: Response Data Bytes for Test Digital Output

1 Unsigned-8 Test DO Type
Test Stop
Pulse
Frequency
Alarm;
2-5 Unsigned-32 Test value
Table 94: Command-Specific Response Codes for Test Digital Output

1 Undefined
3-4 Undefined
8-15 Undefined
8-127 Undefined

Command 192 (0xC0): Read Pipe Size

This command is to read pipe size.
Table 95: Request Data Bytes for Read Pipe Size

None
Table 96: Response Data Bytes for Read Pipe Size

0 Unsigned-8 Pipe size unit
1-4 Float Pipe OD Value
5-8 Float Pipe ID Value
9 - 12 Float Pipe WT Value
Table 97: Command-Specific Response Codes for Read Pipe Size

1-5 Undefined
7-127 Undefined

Command 193 (0xC1): Read Pipe Material

This command is to read pipe material.
Table 98: Request Data Bytes for Read Pipe Material

None
Table 99: Response Data Bytes for Read Pipe Material

0-3 Unsigned-32 Pipe Material
4-7 Float Pipe Sound speed
Table 100: Command-Specific Response Codes for Read Pipe Material

1-5 Undefined
7-127 Undefined
Command 194 (0xC2): Read Pipe Lining Attribute

This command is to read pipe lining attribute.
Table 101: Request Data Bytes for Read Pipe Lining Attribute
None
Table 102: Response Data Bytes for Read Pipe Lining Attribute
0 Unsigned-8 Lining Existing
1–4 Float Lining Thickness
5-8 Unsigned-32 Lining Material
9 – 12 Float Lining Sound speed
Table 103: Command-Specific Response Codes for Read Pipe Lining Attribute
1-5 Undefined
7-127 Undefined

Command 195 (0xC3): Read Sensor Meter Setup

This command is to read the sensor meter setup.
Table 104: Request Data Bytes for Read Sensor Meter Setup
None
Table 105: Response Data Bytes for Read Sensor Meter Setup
0-3 Float Zero Cutoff
Table 106: Command-Specific Response Codes for Read Sensor Meter Setup
1-5 Undefined
7-127 Undefined

Command 196 (0xC4): Read Transducer Information

This command is to read transducer information.
Table 107: Request Data Bytes for Read Transducer Information

None
Table 108: Response Data Bytes for Read Transducer Information

0-3 Unsigned-32 Transducer type:
0: Other;
10: CPT-0.5
11: CPT-2.0
12: CPT-0.5-MT C-PB-05-M
13: CPT-1.0-MT C-PB-10-M
14: CPT-2.0-MT C-PB-20-M
15: CPT-0.5-HT
16: CPT-1.0-HT
17: CPT-2.0-HT
18: CPS-0.5
19: CPSM-2.0
20: CTS-1.0
21: CTS-1.0-HT
22: CTS-2.0
23: C-LP-40-HM
24: C-LP-40-NM
25: CPB-0.5-HT
26: CPB-2.0-MT
27: CPB-0.5-MT
28: CPB-2.0
29: CPB-0.5
30: CPS-1.0 CPT-1.
31: CWL-2
32: CPS-1.0
33: CPW (WT-1P-1.0 on AB82
34: CPW (WT-1P-0.5 on NDT plastic
36: CPB-1.0-HT

Table 108: Response Data Bytes for Read Transducer Information (cont.)
37: CPB-2.0-HT
38: CPB-1.0
39: CPB-1.0-MT
301: C-RL-0.5
302: C-RL-1
304: C-RL-0.5
305: C-RL-1
307: C-RL-0.5
308: C-RL-1
310: C-RV-0.5
311: C-RV-1
313: C-RW-0.5
314: C-RW-1
401: C-RS 0.5M
402: C-RS 1M
403: C-RS 2M
407: UTXDR-2
408: UTXDR-5
601: CAT0.5M
602: CAT1M
603: CAT2M
4-7 Unsigned-32 Transducer Frequency
8 - 11 Unsigned-32 Transducer Wedge Type
12 - 15 Float Transducer Wedge Angle
16 - 19 Float Transducer Wedge SOS
20 - 23 Float Transducer Tw
Command 196 (0xC4): Read Transducer Information
Table 109: Command-Specific Response Codes for Read Transducer Information

1-5 Undefined
7-127 Undefined

Command 197 (0xC5): Read Transducer Traverses and Spacing

This command is to read transducer traverses and spacing.
Table 110: Request Data Bytes for Read Transducer Traverses and Spacing
None
Table 111: Response Data Bytes for Read Transducer Traverses and Spacing
0 Unsigned-8 Transducer traverse
1-4 float Transducer spacing
Table 112: Command-Specific Response Codes for Read Transducer Traverses and Spacing
1-5 Undefined
7-127 Undefined

Command 198 (0xC6): Read Fluid Information

This command is to read fluid information.
Table 113: Request Data Bytes for Read Fluid Information

None
Table 114: Response Data Bytes for Read Fluid Information

0-3 Unsigned-32 Fluid Type:
0: Other
1. Water
4-7 Float Fluid SOS
8 – 11 Float Fluid minimum SOS
12 - 15 Float Fluid Maximum SOS
16 - 19 Float Fluid Temperature
Table 115: Command-Specific Response Codes for Read Fluid Information

1-5 Undefined
7-127 Undefined
Command 200 (0xC8): Write Pipe Size

This command is to write pipe size.
Table 116: Request Data Bytes for Write Pipe Size


Command 200 (0xC8): Write Pipe Size (cont.)
Table 117: Response Data Bytes for Write Pipe Size

Table 118: Command-Specific Response Codes for Write Pipe Size

1-4 Undefined
8-15 Undefined
17 Undefined
18 Error Wrong Unit code
19-127 Undefined
Command 201 (0xC9): Write Pipe Material

This command is to write Pipe Material.
Table 119: Request Data Bytes for Write Pipe Material

Table 120: Response Data Bytes for Write Pipe Material


Command 201 (0xC9): Write Pipe Material (cont.)
Table 121: Command-Specific Response Codes for Write Pipe Material

1-4 Undefined
8-15 Undefined
17-127 Undefined
Command 202 (0xCA): Write Pipe Lining Attribute

This command is to write pipe lining attribute.
Table 122: Request Data Bytes for Write Pipe Lining Attribute
Table 123: Response Data Bytes for Write Pipe Lining Attribute

Command 202 (0xCA): Write Pipe Lining Attribute (cont.)
Table 124: Command-Specific Response Codes for Write Pipe Lining Attribute
1-4 Undefined
8-15 Undefined
17-127 Undefined
Command 203 (0xCB): Write Sensor Meter Setup

This command is to write sensor meter setup.
Table 125: Request Data Bytes for Write Sensor Meter Setup
Table 126: Response Data Bytes

Table 127: Command-Specific Response Codes for Write Sensor Meter Setup
1-4 Undefined
8-15 Undefined
17-127 Undefined

Command 204 (0xCC): Write Transducer Information

This command is to write transducer information.
Table 128: Request Data Bytes for Write Transducer Information

0: Other;
10: CPT-0.5
11: CPT-2.0
12: CPT-0.5-MT C-PB-05-M
13: CPT-1.0-MT C-PB-10-M
14: CPT-2.0-MT C-PB-20-M
15: CPT-0.5-HT
16: CPT-1.0-HT
17: CPT-2.0-HT
18: CPS-0.5
19: CPSM-2.0
20: CTS-1.0
21: CTS-1.0-HT
22: CTS-2.0
23: C-LP-40-HM
24: C-LP-40-NM
25: CPB-0.5-HT
26: CPB-2.0-MT
27: CPB-0.5-MT
28: CPB-2.0
29: CPB-0.5
30: CPS-1.0 CPT-1.0
31: CWL-2
32: CPS-1.0
33: CPW (WT-1P-1.0 on AB82
36: CPB-1.0-HT
37: CPB-2.0-HT
38: CPB-1.0
39: CPB-1.0-MT

Table 128: Request Data Bytes for Write Transducer Information (cont.)
301: C-RL-0.5
302: C-RL-1
304: C-RL-0.5
305: C-RL-1
307: C-RL-0.5
0: Other;
12 – 15 Unsigned-32 Transducer Wedge Angle
16 – 19 Unsigned-32 Transducer Wedge SOS
20 - 23 Unsigned-32 Transducer Tw
Command 204 (0xCC): Write Transducer Information (cont.)
Table 129: Response Data Bytes for Write Transducer Information

0: Other;
12 – 15 Unsigned-32 Transducer Wedge Angle
16 – 19 Unsigned-32 Transducer Wedge SOS
20 - 23 Unsigned-32 Transducer Tw
Table 130: Command-Specific Response Codes for Write Transducer Information

1-4 Undefined
8-15 Undefined
17-127 Undefined

Command 205 (0xCD): Write Transducer Traverses and Spacing

This command is to write transducer traverses and spacing.
Table 131: Request Data Bytes for Write Transducer Traverses and Spacing
1-4 float Transducer spacing
Table 132: Response Data Bytes for Write Transducer Traverses and Spacing
1-4 Unsigned-32 Transducer spacing
Table 133: Command-Specific Response Codes for Write Transducer Traverses and Spacing
1-4 Undefined
8-15 Undefined
17-127 Undefined

Command 206 (0xCE): Write Fluid Information

This command is to write fluid information.
Table 134: Request Data Bytes for Write Fluid Information

0: Other
1. Water
4-7 Float Fluid SOS
Table 135: Response Data Bytes for Write Fluid Information

0: Other
1. Water
4-7 Float Fluid SOS
Table 136: Command-Specific Response Codes

1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined

Command 208 (0xD0): Read Calibration Configuration

This command is to read Calibration Configuration.
Table 137: Request Data Bytes for Read Calibration Configuration

None
Table 138: Response Data Bytes for Read Calibration Configuration

0 Unsigned-8 Reynolds correction
1 Unsigned-8 Active MultiK Enable
2 Unsigned-8 KFactor Type:
0: Velocity, 1: Reynolds
3–6 Float Static KFactor
7 Unsigned-8 KFactor Points
8 - 11 Float Kinematic Viscosity
Table 139: Command-Specific Response Codes for Read Calibration Configuration

1-5 Undefined
7-127 Undefined

Command 209 (0xD1): Read Velocity KFactor Table

This command is to read the Velocity KFactor table.
Table 140: Request Data Bytes for Read Velocity KFactor Table
0 Unsigned-8 Velocity KFactor Index (1 - 6)
Table 141: Response Data Bytes for Read Velocity KFactor Table
1 Unsigned-8 Velocity Unit
2–5 Float Velocity Value
6–9 Float Velocity KV Value;
Table 142: Command-Specific Response Codes for Read Velocity KFactor Table
1 Undefined
3-4 Undefined
7-127 Undefined

Command 210 (0xD2): Read Reynolds KFactor Table

This command is to read Reynolds KFactor table.
Table 143: Request Data Bytes for Read Reynolds KFactor Table
0 Unsigned-8 Reynolds KFactor Index (1 - 6)
Table 144: Response Data Bytes for Read Reynolds KFactor Table
1–4 Float Reynolds Value
5–8 Float Reynolds KV Value;
Table 145: Command-Specific Response Codes for Read Reynolds KFactor Table
1 Undefined
3-4 Undefined
7-127 Undefined

Command 216 (0xD8): Write Calibration Configuration

This command is to write Calibration Configuration.
Table 146: Request Data Bytes for Write Calibration Configuration

0 Unsigned-8 Reynolds correction: 0: Disable, 1: Enable
1 Unsigned-8 Active MultiK Enable: 0: Disable, 1: Enable
Table 147: Response Data Bytes for Write Calibration Configuration

0 Unsigned-8 Reynolds correction
1 Unsigned-8 Active MultiK Enable
Table 148: Command-Specific Response Codes for Write Calibration Configuration

1-4 Undefined
8-15 Undefined
17-127 Undefined

Command 217 (0xD9): Write Velocity KFactor Table

This command is to write Velocity KFactor table.
Table 149: Request Data Bytes for Write Velocity KFactor Table
Table 150: Response Data Bytes for Write Velocity KFactor Table
Table 151: Command-Specific Response Codes for Write Velocity KFactor Table
1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined

Command 218 (0xDA): Write Reynolds KFactor Table

This command is to write Reynolds KFactor table.
Table 152: Request Data Bytes for Write Reynolds KFactor Table
Table 153: Response Data Bytes for Write Reynolds KFactor Table
Table 154: Command-Specific Response Codes for Write Reynolds KFactor Table
1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined

Command 224 (0xE0): Read Error Limits

This command is to read flow meter error limits.
Table 155: Request Data Bytes for Read Error Limits

0 Unsigned-8 Error limit:
1. Correlation Peak Limit
2. Acceleration Limit
3. Velocity Low Limit
4. Velocity High Limit
5. Amp Disc Min
6. Amp Disc Max
7. Signal Low Limit
8. Sound Speed Limit
9. Errors Allowed
Table 156: Response Data Bytes for Read Error Limits

1. Correlation Peak Limit
2. Acceleration Limit
3. Velocity Low Limit
4. Velocity High Limit
5. Amp Disc Min
6. Amp Disc Max
7. Signal Low Limit
8. Sound Speed Limit
9. Errors Allowed
1-4 float Error limit Value;
Table 157: Command-Specific Response Codes for Read Error Limits

1 Undefined
3-4 Undefined
7-127 Undefined

Command 225 (0xE1): Read Signal Setup

This command is to read flow meter signal setup.
Table 158: Request Data Bytes for Read Signal Setup

0 Unsigned-8 signal setup type:
1. Delta T Offset
2. Percentage Peak
3. Min Peak Percentage
4. Max Peak Percentage
Table 159: Response Data Bytes for Read Signal Setup

1. Delta T Offset
2. Percentage Peak
3. Min Peak Percentage
4. Max Peak Percentage
1-4 Float signal setup Value
Table 160: Command-Specific Response Codes for Read Signal Setup

1 Undefined
3-4 Undefined
7-127 Undefined

Command 226 (0xE2): Read Flowmeter S/N

This command is to read flow meter s/n.
Table 161: Request Data Bytes for Read Flowmeter S/N

0 Unsigned-8 Flowmeter S/N:
1. Electronic S/N
2. UP Sensor
3. S/N
4. DN Sensor S/N
Table 162: Response Data Bytes for Read Flowmeter S/N

1. Electronic S/N
2. UP Sensor
3. S/N
4. DN Sensor S/N
1 - 16 Unsigned-8 S/N
Table 163: Command-Specific Response Codes for Read Flowmeter S/N

1 Undefined
3-4 Undefined
7-127 Undefined

Command 227 (0xE3): Read Flowmeter Version

This command is to read flow meter version.
Table 164: Request Data Bytes for Read Flow Meter Version
0 Unsigned-8 Flowmeter version
1. Main Hardware version
2. Main Software version
Table 165: Response Data Bytes for Read Flow Meter Version
0 Unsigned-8 Version type:
1, Main Hardware version
2. Main Software version
1-8 Unsigned-8 Version Number
Table 166: Command-Specific Response Codes for Read Flow Meter Version
1 Undefined
3-4 Undefined
7-127 Undefined

Command 232 (0xE8): Write Error Limits

This command is to write flow meter error limits.
Table 167: Request Data Bytes for Write Error Limits

Correlation Peak Limit
Acceleration Limit
Velocity Low Limit
Velocity High Limit
Amp Disc Min
Amp Disc Max
Signal Low Limit
Sound Speed Limit
Errors Allowed
Table 168: Response Data Bytes for Write Error Limits

Correlation Peak Limit
Acceleration Limit
Velocity Low Limit
Velocity High Limit
Amp Disc Min
Amp Disc Max
Signal Low Limit
Sound Speed Limit
Errors Allowed

Command 232 (0xE8): Write Error Limits (cont.)
Table 169: Command-Specific Response Codes for Write Error Limits

1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined

Command 233 (0xE9): Write Signal Setup

This command is to write flow meter signal setup.
Table 170: Request Data Bytes for Write Signal Setup

Delta T Offset
percentage Peak
Min Peak Percentage
Max Peak percentage
Table 171: Response Data Bytes for Write Signal Setup

Delta T Offset
percentage Peak
Min Peak Percentage
Max Peak percentage
Table 172: Command-Specific Response Codes for Write Signal Setup

1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined

Command 239 (0xEF): Reset Flow Meter Data

This command is to reset flow meter data.
Table 173: Request Data Bytes for Reset Flow Meter Data
0 Unsigned-8 Reset type:
1. Reset Error Log
2, Forward Inventory
3. Reverse Inventory
4. Net Inventory
5. Inventory Time
6. All
7. Inventory
Table 174: Response Data Bytes for Reset Flow Meter Data
0 Unsigned-8 Reset type:
Reset Error Log
Forward Inventory
Reverse Inventory
Net Inventory
Inventory Time
All
Inventory
Table 175: Command-Specific Response Codes for Reset Flow Meter Data
1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined

Command 241 (0xF1): Read the Factory Setting

This command is to read the factory setting.
Table 176: Request Data Bytes for Read the Factory Setting
None
Table 177: Response Data Bytes for Read the Factory Setting
0 Unsigned-8 Response time
0.5s
1s
5s
10s
30s
60s
1-4 Unsigned-32 Sample Size:
2
4
8
16
32
Table 178: Command-Specific Response Codes for Read the Factory Setting
1 Undefined
3-4 Undefined
7-127 Undefined

Command 248 (0xF8): Write the Factory Setting

This command is to write the factory setting.
Table 179: Request Data Bytes for Write the Factory Setting
0.5s
1s
5s
10s
30s
60s
2
4
8
16
32
Table 180: Response Data Bytes for Write the Factory Setting
0.5s
1s
5s
10s
30s
60s
2
4
8
16
32

Command 248 (0xF8): Write the Factory Setting (cont.)
Table 181: Command-Specific Response Codes for Write the Factory Setting
1 Undefined
3-4 Undefined
8-15 Undefined
17-127 Undefined
Command 253 (0xFD): Reset to Factory Setting

This command is to reset the setting to the factory default.
Table 182: Request Data Bytes for Reset to Factory Setting

None
Table 183: Response Data Bytes for Reset to Factory Setting

None
Table 184: Command-Specific Response Codes for Reset to Factory Setting

1-4 Undefined
8-15 Undefined
17-127 Undefined

6.3 Additional Device Status

Command 48 returns 4 bytes of data, with the following status information:
Table 185: HART Additional Device Status

HART Additional Device Status
Byte Bit Error Description Class Device Status Bits Set
0 0 Amplitude Error Error 4, 7
1 Low Signal Error 4, 7
2 Sound Speed Error Error 4, 7
3 Velocity Range Error 4, 7
4 Signal Quality Error 4, 7
5 Cycle Skip Error 4, 7
6 Reserve
7 Reserve
1 0 Reserve
1 Reserve
2 Reserve
3 Reserve
4 Reserve
5 Reserve
6 Reserve
7 Reserve
2 0 FPGA error; 4, 7
1 Setting files CRC error; 4, 7
2 Flash Error 4, 7
3 KEY/LED Error 4, 7
4 I/O Error 4, 7
5 Display Error 4, 7
6 RTC Error 4, 7
7 Reserve
3 0 In configure mode; 4, 0
1 Not calibrated; 4, 0
2 Reserve
3 Reserve
4 Reserve
5 Reserve
6 Reserve
7 Reserve

6.4 Device Variables
Table 186: Device Variables

Device Variable Device Variable Classification Code
Measurement
Code Code Classification
Velocity 0 67 Velocity
Actual Volumetric 1 66 Volumetric Flow
Standardized Volumetric 2 66 Volumetric Flow
Fwd. Batch Totals 3 68 Volumetric
Rev Batch Totals 4 68 Volumetric
Net Batch Totals 5 68 Volumetric
Batch Totalizer Time 6 70 Time
Fwd. Inventory Totals 7 68 Volumetric
Rev Inventory Totals 8 68 Volumetric
Net Inventory Totals 9 68 Volumetric
Inventory Totalizer Time 10 70 Time
Mass Flow 11 72 Mass flow
Sound Speed 12 67 Velocity
Reynolds 13 0 Not Classified
Kfactor 14 0 Not Classified
Transit Time Up 15 70 Time
Transit Time Dn 16 70 Time
DeltaT 17 70 Time
Up Signal Quality 18 0 Not Classified
Dn Signal Quality 19 0 Not Classified
Up Amp Disc 20 0 Not Classified
Dn Amp Disc 21 0 Not Classified
SNR Up 22 0 Not Classified
SNR Dn 23 0 Not Classified
ActiveTW Up 24 0 Not Classified
ActiveTW Dn 25 0 Not Classified
Gain Up 26 0 Not Classified
Gain Dn 27 0 Not Classified
Error Status 28 0 Not Classified
Reported Error 29 0 Not Classified
Up Peak 30 0 Not Classified
Down Peak 31 0 Not Classified
Peak% Up 32 81 Analytical
Peak% Down 33 81 Analytical

6.5 HART Engineering Units

The unit types allowed for the AT600 flow meter device variables are listed below
Table 187: HART Engineering Units

Device Variable Unit
Code Classification Code Description
64 Temperature 32 Degrees Celsius
33 Degrees Fahrenheit
66 Volumetric Flow 27 cubic feet per day
130 Cubic feet per hour
15 Cubic feet per minute
26 Cubic feet per second
187 Standard cubic feet per day
185 Standard cubic feet per hour
123 Standard cubic feet per minute
186 Standard cubic feet per second
29 Cubic meter per day
19 Cubic meter per hour
131 Cubic meters per minute
28 Cubic meters per second
240 Million cubic meters per day
187 Standard cubic Meter per Day
188 Standard cubic meter per hour
189 Standard cubic meter per minute
190 Standard cubic meter per second
235 gallon per day
136 Gallons per hour
16 Gallons per minute
22 Gallons per second
135 Barrels per day
134 Barrels per hour
133 Barrels per minute
132 Barrels per second
174 Liters per day
138 Liters per hour
17 Liters per minute
24 Liters per second
25 million liters per day
177 Standard liter per day
178 Standard liter per hour

Table 187: HART Engineering Units (cont.)

179 Standard liter per minute
180 Standard liter per second
67 Velocity 20 Feet per second
21 Meters per second
68 Volume 43 Cubic Meter
41 Cubic Decimeter (Liter)
243 Mega Liters
244 Million Cubic Meter
112 Cubic Feet
40 Gallon
46 Barrel
245 Mega Gallons
246 Million Cubic feet
172 Standard Cubic Meter
171 Standard Liters
61 Kilogram
62 Metric Ton
168 Standard Cubic Feet
63 Pound
247 Kilo Pound
64 Short Tons
69 Length 44 Feet
47 Inch
45 Meter
49 Millimeter
70 Time 172 Nanoseconds
171 Microseconds
170 Milliseconds
51 Seconds
50 Minute
52 Hour
53 Day
72 Mass Flow 73 Kilograms per seconds
74 Kilograms per minute
75 Kilograms per hour
76 Kilograms per day
242 Metric tons per second

Table 187: HART Engineering Units (cont.)

77 Metric tons per minute
78 Metric tons per hour
79 Metric tons per day
80 pounds per seconds
81 pounds per minute
82 pounds per hour
83 pounds per day
241 Short ton per seconds
84 Short ton per minute
85 Short ton per hour
86 Short
[no content intended ton per
for this day
page]
73 Mass per Volume 94 Pounds per cubic feet
92 Kilograms per cubic meter
74 Viscosity 54 Centistokes
248 Square Meter per Sec
81 Analytical 57 Percent
96 Acceleration 171 Feet per second squared
172 Meter per second squared
0 Not Classification 38 dB
156 Hertz



A.1 Overall Operation and Performance
Fluid Types
Liquids: acoustically conductive fluids, including most clean liquids, and many liquids with small amounts
of
entrained solids or gas bubbles
Flow Measurement
Correlation Transit-Time™ mode
Pipe Sizes
0.5 in. (15 mm) or greater
Pipe Materials
All metals and most plastics. Consult BHGE for concrete, composite materials, and highly corroded or lined
pipes.
Accuracy
±1% of reading in application, for 2 in. (50 mm) pipe and >1 ft/s (0.3 m/s) velocity
±2% of reading in application, for <2 in. (50 mm) pipe and >1 ft/s (0.3 m/s) velocity
±0.5% in field calibration
Note: Installation assumes a fully developed, symmetrical flow profile (typically 10 diameters upstream and
5 diameters downstream of straight pipe run). Final installation accuracy is a function of multiple
factors including fluid, temperature range, pipe centricity and others.
Calibration
All meters are water calibrated and delivered with a traceable calibration certificate.
Repeatability
±0.2% of reading
Range (Bidirectional)
-40 to +40 ft/s (-12 to +12 m/s)
Rangeability (Overall)
400:1
Measurement Parameters
Velocity, Volumetric, and Totalized Flow

A.2 Electronics
Enclosure
Epoxy-coated, copper free, aluminum weatherproof Type 4X/IP67
Dimensions
6.6 x 5.0 x 2.4 in. (168 x 128 x 61 mm)
Weight
3.5 lb/1.5 kg
Channels
One channel
Display
Graphic LCD (128 x 64 pixels)
Keypad
Six-button keypad for full functionality operation
Error Display Indicator

Green or Red light
Power Supplies
Standard: 85 to 265 VAC, 50/60 Hz
Optional: 12 to 28 VDC, ± 5%
Power Consumption
In-rush: 10 W
Normal operation: 5 W
Operating Temperature
-4 to 131°F (-20 to 55°C)
Storage Temperature
-40 to 158°F (-40 to 70°C)

A.2 Electronics (cont.)

Outputs (Based on Configuration)
• 4-20 mA (24VDC powered, 600  maximum load, 1500 VDC isolation)
• Frequency, Pulse, Alarm (Passive output, 100 VDC, 1 A/1 W maximum, 1500 VDC isolation)
• HART (FSK modulation, Category Flow, Protocol Version 7.5, Device Revision 2, MFG ID 157,
Device Type Code 127, Number of device variables 34)
• Modbus/RS485 (Half-duplex, 1500 VDC isolation)
Note: Analog outputs are Namur NE43 compliant.
Certification
CE, UL, CSA, (MCert approval pending)
A.3 Clamp-On Ultrasonic Flow Transducers

Materials
• AT6 Transducer
Transducer Body: Aluminum (ASTM AL6061)
Fixture Body: Aluminum (ASTM AL6061)/Stainless Steel (ASTM A316)
• C-RS Transducer
Transducer Body: Stainless Steel (ASTM A316)
Fixture Body: Stainless Steel
• UTXDR Transducer
Transducer Body: Aluminum (ASTM AL6061)
Fixture Body: Aluminum (ASTM AL6061)/Stainless Steel (ASTM A304)
• CF-LP Transducer
Fixture Body: Aluminum (ASTM AL6061)
• C-PT Transducer
Fixture Body: Stainless Steel
Note: Contact BHGE for other transducer models.

A.3 Clamp-On Ultrasonic Flow Transducers (cont.)

Temperature Range
• AT6 Transducer: -40 to 302°F (-40 to 150°C)
• C-RS Transducer: -40 to 302°F (-40 to 150°C)
• UTX Transducer: -40 to 248°F (-40 to 120°C)
• CF-LP Transducer: -40 to 446°F (-40 to 230°C)
• C-PT Transducer: -4 to 410°F (-20 to 210°C)
Note: Contact BHGE for other transducer models.
Humidity Range
Up to 90% RH
Note: Contact BHGE for tropicalization of the unit for 100% RH.
Altitude Range
Up to 2000 m (6500 ft) maximum
Altitude Range
Up to 2000 m (6500 ft) maximum
CAT Transducer Cables

Cable: RG316 coaxial cable, up to 90 m (300 ft) long,
Temperature Range: -40 to 302°F (-40 to 150°C)
Couplant
Standard: Solid couplant
Optional: Liquid couplant
Rating
Standard: General purpose (IP66 or IP68)
Note: See specific transducer model for exact rating.

A.4 General
A.4.1 Wiring Cable Specifications and Requirements
• Cable diameter range for PWR connection: 7 to 12mm, refer to Gland Hole 1 on Figure 24 on page 24
• Cable diameter range for Hart, Modbus and I/O connection: 5 to 8mm, refer to Gland Hole 2,3 and 4 in
Figure 24 on page 24
• Temperature range of cable for PWR, Hart, Modbus and IO connection: 14° to 185°F (-10° to 85°C)
The cable should meet the CE and UL standard below:
Conductor cross section solid range: 0.2 mm2to 2.5 mm2

Conductor cross section stranded range: 0.2 mm2to 2.5 mm2
Conductor cross section stranded, with ferrule without plastic sleeve range: 0.25 mm2 to 1 mm2
Conductor cross section stranded, with ferrule with plastic sleeve range: 0.25 mm2 to 1 mm
Conductor cross section AWG/kcmil range: 12 to 26 AWG according to UL/CUL range: 14 to 28
A.4.2 Cable Fixing Requirement and Gland Torque

Refer to Figure 24 on page 24 for the Gland Hole position.
To make a reliable IP67 sealing performance of the enclosure during cabling, the gland must be tightened
well, below torque value is a reference to make a reliable NEMA 4X/IP67 sealing between cable and gland:
• Operation torque for Gland Hole 1 and 5: 2.7 N.M
• Operation torque for Gland Hole 2, 3 and 4: 2.5 N.M
A.4.3 Display Languages

English/Chinese/German/French/Italian/Japanese/Portuguese/Russian/Spanish/Swedish/Turkish
Note: The meter will be set to the language specified by the customer before shipping.
A.4.4 Product Models

Based on the line power type, the AT600 ultrasonic flow meter is available in two series:
• Models of AC meter: 85-264VAC, 50-60Hz, 10W, Class I
AT6-**-****-****-*-1-*-**-**-*-*, AT6KIT-*1, AT6KIT-*2, AT6KIT-*3 and AT6KIT-*7
• Models of DC meter: 12-28VDC, 10W, Class I
AT6-**-****-****-*-2-*-**-**-*-*, AT6KIT-*4, AT6KIT-*5, AT6KIT-*6 and AT6KIT-*8
Note: * in the product model name is either a number from 0-9 or a letter from A-Z.



B.1 Service Record
Whenever any service procedure is performed on the AT600 flow meter, the details of the service should be
recorded in this appendix. An accurate service history of the meter can prove very helpful in troubleshooting
any future problems.
B.2 Data Entry

Record the complete and detailed service data for the AT600 in Table 188 below. Make additional copies of
the table as needed.
Table 188: Service Record

Date Description of Service Performed Performed

B.3 Initial Settings

The values for the initial measurement settings immediately after commissioning of the meter and
verification of proper operation should be entered below.
Table 189: Initial Settings

Parameter Initial Value
Pipe OD
Pipe ID
Pipe Wall Thickness
Pipe Material
Pipe Sound speed
Lining Thickness
Lining Material
Transducer ID
Transducer Frequency
Transducer Wedge Type
Transducer Wedge Angle
Transducer Wedge SOS
Transducer TW
Traverses
Fluid Type
Fluid SOS
Fluid Minimum SOS
Fluid Maximum SOS
Fluid Temperature
Transducer Spacing

B.4 Diagnostic Parameters

The values for the diagnostic parameters immediately after commissioning of the meter and verification of
proper operation should be entered below. These initial values can then be compared to current values to
help diagnose any future malfunction of the system.
Table 190: Diagnostic Parameters

Parameter Initial Value
Velocity
Actual Volumetric
Standardized Volumetric
Fwd. Batch Totals
Rev Batch Totals
Net Batch Totals
Batch Totalizer Time
Fwd. Inventory Totals
Rev Inventory Totals
Net Inventory Totals
Inventory Totalizer Time
Mass Flow
Sound Speed
Reynolds
Kfactor
Transit Time Up
Transit Time Dn
DeltaT
Up Signal Quality
Dn Signal Quality
Up Amp Disc
Dn Amp Disc
SNR Up
SNR Dn
ActiveTW Up
ActiveTW Dn
Gain Up
Gain Dn
Error Status
Reported Error
Up Peak
Down Peak
Peak % Up
Peak % Down



C.1 Introduction
The AT600 firmware can be updated in the field. However, before attempting a firmware update, read the
information in this section thoroughly to ensure a successful update process.
Note: The instructions in this appendix are also available in BHGE document p/n 714-1418.
C.1.1 System Requirements

Make sure that your AT600 flow meter system meets the following requirements:
• Verify that your current AT600 firmware version is 01.02.25 or later.
• Verify that you have the AquaTrans Flow Meter Software Update version 20161117V1.2 or later available to
run on your PC.
• Verify that your AT600 service port has a 2-wire RS485 connection to your PC, and that the connection
Baud Rate is set to 115200 baud.
• Verify that your AT600 firmware binary file is Version 1.02.25 or later.
C.1.2 Preparation
To ensure a successful firmware update, be prepared for the following:
• Allow about 10 minutes for the firmware update to complete.
• Before starting the firmware update, make sure that the AT600 is in normal measurement mode.
• The AT600 main power must remain ON throughout the firmware update. DO NOT turn the main power
OFF until the firmware update has been completed.
• Because the firmware update uses the AT600 Modbus/Service Port, you must NOT allow any other AT600
Modbus activity during the firmware update.
• During the firmware update, the AT600 will attempt to validate the new firmware image file. At the
end of the update process, if the validation was successful, the AT600 will reboot with the updated
firmware installed. However, if the validation was not successful, the original firmware will still be
installed after the reboot.

C.2 Performing the Firmware Update

If your AT600 flow meter system meets all of the requirements discussed on the previous page and you are
prepared to perform the firmware update according to those guidelines, proceed with the instructions in this
section.
C.2.1 Check the Current Firmware Version

To determine the firmware version currently installed in your AT600, access the following information
screen:
Main Menu > Program > Advanced > Flow Meter Data > Main Board > SW Version
For reference, an example of this screen is shown in Figure 36 below.
SW Version
01.02.23
Figure 36: Example Software Version Screen
Note: As indicated on the previous page, the current version of your AT600 firmware must be 01.02.23 or later.
If your version is older than this, you cannot use this update method. Software versions 01.02.24,
01.03.xx, 02.xx.xx are examples of acceptable versions.
C.2.2 Update Steps

If your AT600 firmware version qualifies for the field firmware update process, complete the following steps:
1. Prepare the RS485 Modbus connection:
a. Disconnect the main power from the AT600.
b. Wire the Modbus connection as described in “Wiring the Modbus Communication” on page 28.
2. Locate the AquaTrans Flow Meter Software Update (version 20161117V1.2 or later) software on your
PC. If the folder containing the software is zipped, you must unzip it prior to use.

C.2.2 Update Steps (cont.)

3. Run the update software by clicking on the Upgrade.exe file (see Figure 37 below). Installation of the
software on the PC is not required.
Figure 37: Running the Update.exe Software
4. Click on the COM Port button and enter the specific com port on the PC that is connected to the AT600
Modbus/Service Port.
5. Click on the Open Image File button, and open the BHGE image file to be used for the AT600 firmware
update.
6. Click on the Start To Upgrade button. After verifying that the selected image file and Com port are
correct, click the OK button to start the update process.
7. After the progress bar indicates that the firmware update is 100% complete (about 10 minutes), the
message shown in Figure 38 below will be displayed. Note that the AT600 will automatically reboot in
30 seconds.
Figure 38: Reboot Message
8. After the reboot is complete, refer to “Check the Current Firmware Version” on page 184 and confirm
that the new firmware version has been installed. If the original firmware version is still installed,
the AT600 was not able to validate the image file that was used - contact BHGE for assistance.

C.3 Clearing an S2 Warning

After the firmware update, the AT600 may show an S2 warning. If so, complete the following steps:
1. In the update software, click on the Com Port button and select the specific port that was used for the
update (see top red box in Figure 39 below).
2. Click on the Clear S2 Warning button (see bottom red box in Figure 39 below).
Figure 39: Clearing an S2 Warning

3. After about 15 seconds, a screen similar to Figure 40 below is displayed. Click OK and then reboot the
AT600 to confirm that the S2 error has been cleared.
Figure 40: S2 Warning Successfully Cleared
C.4 Support
If the firmware update was unsuccessful, reboot the AT600 and repeat the procedure described in this
appendix. If there is still a problem, send an email to mstechsupport@ge.com and describe the problem in
detail.

AquaTrans™ AT600 User’s Manual
Press ¤to enter the Display Measurement menu.
Velocity Standard Volumetric Batch Total Sound Speed K-Factor

Actual Volumetric Mass Inventory Total Reynolds Diagnostic

D.1 The Display Measurement Menu
Forward Reverse
Net Time (min)
Flow Parameters Signal Quality Signal Process System Status
Transit time Up Up Signal Quality Dn Signal Quality Active TWup Active TWdn Peak Up Peak Dn
usec unitless unitless usec usec unitless unitless
Transit time Dn Up Amp Disc Dn Amp Disc Gainup Gaindn Peak pct Up Peak pct Dn
Figure 41: The Display Measurement Menu

usec unitless unitless dB dB
Detla T SNR Dn SNR Up Error Status Report Error
nsec unitless unitless unitless(enum) unitless(enum)
187
188
Display
Locked
Esc > Enter > Esc Unlocked

D.2 The Main Menu
Main Menu
Yes English ѝ᮷

1 Variable 2 Variables Totalizer Password
xxxx No Deutsch Français
Italiano ᰕᵜ䃎
Português ƴǗǕǕǎǌǍ
Española Svenska
Turkish
Figure 42: The Main Menu

User Preferences Inputs/Outputs Sensor Setup Calibration Advanced Factory
Save Changes?
No Yes
Display

Display
Main Menu

Password
USER PREFERENCES INPUT/OUTPUT SENSOR SETUP CALIBRATION ADVANCED FACTORY
Setting Units Density Password Display
Meter Tag Density (Actual) Backlight
Label Density (Reference)

Off On
Syetem Date
Timeout
D.3 The Main Menu > User Preferences Menu
xxx seconds
Velocity Act Volumetric Std Volumetric Mass Totalizer Density Pipe Dimension Temperature Acceleration
Confirmation
Figure 43: The Main Menu > User Preferences Menu

No Yes
Units
Metric English
189
190
Display To enter the Input/Output menu, on this initial screen, hightlight the lock symbol and prHVV¤6HOHFW3rogram and prHVV¤
Then enter a passworG,QWKH8VHU3referHQFHPHQXVHOHFW6HWWLQJWKHQSress the right arrow kH\
Main Menu
Display Format 3rogram 3rogram Review Keypad Lockout Language
3assword
xxxx
8VHU3references Inputs/Outputs 6HQVRU6HWXS Calibration Advanced Factory
Analog Output A Digital Output X

0RGEXV6Hrvice 3ort
Analog Measurement
Band Rate Bits/3arity
Base Value Do B Do C
Alarm
Velocity ActVolumetric
Full Value 115200 8 even
Alarm 6tate OFF
6tGVolumetric Mass
Calibrate Alarm Type Address
Normal 3XOVH
4 mA 20 mA Inventory Total Batch Total
Low High
D.4 The Main Menu > Inputs/Outputs Menu
3XOVHValue 3XOVH7LPH Modbus 6top

Failsafe
6RXQG6SHHG Forward
3erFHQWDJHRI6FDOH Fault Measurement Error Handling
Alarm Value 1
Diagnostic Reverse THVW3XOVH 6top
Error Handling Measurement
Alarm Type Frequency
Hold Low Net Fwd Batch
Velocity
High Other 6tGVolumetric Rev Batch Measurement
Time
ActVolumetric Base Value
Net Batch Velocity ActVolumetric
Flow parameters 6HH Mass Full Value
Diagnostic Batch Total
6LJQDO4XDOLW\ 6Freen List 6tGVolumetric Mass
Inventory Total Full Frequency
for
3arameters Batch Total Inventory Tool
Figure 44: The Main Menu > Inputs/Outputs Menu

6\VtHP3rocess Diagnostic 6RXQG6SHHG Test Frequency
6LJQDO6tatus 6RXQG6SHHG Diagnostics

6HH Flow 3arameters 6\Vtem 6tatus Error Handling
Diagnostic 6HH
6Freen List Hold Low Diagnostic Flow 3arameters 6LJQDO4XDOLW\
for 6LJQDO4XDOLW\ 6LJQDO3rocess
6Freen List
3arameters High Other for 6\Vtem 6tatus 6LJQDO3rocess
3arameters

Display To enter the Sensor Setup menu, on this initial screen, hightlight the lock symbol and prHVV¤6HOHFW3rogram and prHVV¤
Then enter passworG,QWKH8VHU3reference menu, select Setting, then press the right arrow kH\WLPHV
Main Menu

3assword
xxxx
8VHU3references ,QSXWV2XWSXWV Sensor Setup Calibration Advanced Factory
Meter Setup Mounting Type 3LSH Transducer Traverse Fluid Type Fluid temperature 3DWK
Clamp-on
Fluid temperature Transducer Space
Zero Cutoff 3LSH2' Wall Thickness STD 1 Water
Wetted
3LSH,' 3LSH0Dterial 63(& 2 2WKHU 3DWK/HQJWK
D.5 The Main Menu > Sensor Setup Menu
Lining Steel Frequency 3 Tracking Window

Axial Length
Lining Material ,ron Wedge Type 4
Lining Thickness Cu Wedge Angle 5 Yes No
Al :HGJH626 6 Minimum SNSD Fluid SNSD
Brass Tw Maximum SNSD
CuNi
Glass
3/6TC
Figure 45: The Main Menu > Sensor Setup Menu

2WKHU
191
192
Display To enter the calibration menu, on this initial screen, hightlight the lock symbol and prHVV¤6HOHFW3rogram and prHVV¤
Then enter passworG,QWKH8VHU3referHQFHPHQXVHOHFW6HWWLQJWKHQSress the right arrow kH\WLPHV
Main Menu
3assword
xxxx
8VHU3references ,QSXWV2XWSXWV 6HQVRU6HWXS Calibration Advanced Factory
Calibration Reynolds Correction

D.6 The Main Menu > Calibration Menu
Kinematic Viscosity
Type 6tatic 3oints Table
Velocity 3oint #1
Reynolds 3oint #2
Figure 46: The Main Menu > Calibration Menu

3oint #3
3oint #4
3oint #5
3oint #6

Display To enter the Advanced menu, on this initial screen, hightlight the lock symbol and prHVV¤6HOHFW3rogram and prHVV¤
Main Menu

3assword
xxxx

D.7 The Main Menu > Advanced Menu
Error Limits 6LJQDO6HWXS Error Log ,Qventory RHVHW,Qventory
Correlation 3eak Limit 'HOWD72IIVHW View Log ElectrRQLF61 ForwarG,QY
Acceleration Limit percentage 3eak Reset Error Log 6HQVRU61 ReverVH,QY
Velocity Low Limit Min 3eak 3ercentage Main Board 1HW,Qventory
Velocity High Limit Max 3eak 3ercentage ,Qventory Time
Amp Disc Min All
Figure 47: The Main Menu > Advanced Menu

Amp Disc Max
6LJQDO/RZOLPLW
6RXQGVSHHG/LPLW
Errors Allowed
193
194
Display To enter the Factory menu, on this initial screen, hightlight the lock symbol and prHVV¤6HOHFW3rogram and prHVV¤
Main Menu
3assword
xxxx

D.8 The Main Menu > Factory Menu
Test Reset to Factory Change Digital Comm Response time 6DPSOH6L]H
Watchdog Test Keypad Test V 2
LCD Test ,2Tests 1s 4
5s 8
All Black $QDORJ2XWSXW$ 'LJLWDO2XWSXW% 'LJLWDO2XWSXW&
10s 16
Figure 48: The Main Menu > Factory Menu

All White Calibrate 4 mA 2II 2II
30s 32
Calibrate 20 mA 3XOVH 3XOVH
60s
3erFHQWDJHRI6FDOH Frequency Frequency
Alarm Alarm

Index
A Error Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Alarm Measurement Type, Setting . . . . . . . . . . . . . . . . . .59 Error Handling, Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Alarm State, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Error Header. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Alarm Type, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Escape Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Alarm Value, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 F
Alarm, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Fixture Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Analog Measurements, Setting . . . . . . . . . . . . . . . . . . . . . .49
Flow Error String. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Analog Output Menu, Programming . . . . . . . . . . . . . . . . .48
Flowcell Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Analog Output, Calibrating . . . . . . . . . . . . . . . . . . . . . . . . . .50
Fluid Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Arrow Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Fluid Temperature, Programming . . . . . . . . . . . . . . . . . . . 85
AT Transducers System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fluid Type, Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
AT600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Frequency Error Handling, Setting. . . . . . . . . . . . . . . . . . . 57
Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Frequency Measurement Type, Setting . . . . . . . . . . . . . . 56
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
AT600 Mounting Installation Base . . . . . . . . . . . . . . . . . . . . 6 H
B HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64, 105
Device Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Device Specific Commands . . . . . . . . . . . . . . . . . . . . . .106
Base Value/Full Value/Frequency, Setting. . . . . . . . . . . .56
HART Additional Device Status. . . . . . . . . . . . . . . . . . . . .166
C HART Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Clamp-on Fixture Enter/Exit Fixed Loop Current . . . . . . . . . . . . . . . . . . .119
Mounting onto Pipe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Login with Password . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Logout and Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
D Logout without Saving. . . . . . . . . . . . . . . . . . . . . . . . . . .109
Decimal Places Read Alarm Configuration . . . . . . . . . . . . . . . . . . . . . . .128
Programming for Totalizer . . . . . . . . . . . . . . . . . . . . . . . .35 Read Analog Measurement Range Values . . . . . . . .117
Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Read Backlight Setting . . . . . . . . . . . . . . . . . . . . . . . . . .113
Device Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Read Calibration Configuration . . . . . . . . . . . . . . . . . .149
Device Specific Commands . . . . . . . . . . . . . . . . . . . . . . . 106 Read Current User Access Right . . . . . . . . . . . . . . . . .110
Device Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Read Density Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Read Digital Configuration. . . . . . . . . . . . . . . . . . . . . . .125
Digital Communications, Programming . . . . . . . . . . . . . .61 Read Error Limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Digital Output Menu, Programming. . . . . . . . . . . . . . . . . .51 Read Factory Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
Digital Output, Disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Read Flowmeter S/N . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Read Flowmeter Version . . . . . . . . . . . . . . . . . . . . . . . .158
Display Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Read Fluid Information . . . . . . . . . . . . . . . . . . . . . . . . . .141
Display, Programming the . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Read Frequency Configuration. . . . . . . . . . . . . . . . . . .127
Document Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i Read Loop Current Error Handling . . . . . . . . . . . . . . .118
Down Arrow Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Read Pipe Lining Attribute . . . . . . . . . . . . . . . . . . . . . . .136
Read Pipe Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
E
Read Pipe Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
E1 Low Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Read Pulse Configuration. . . . . . . . . . . . . . . . . . . . . . . .126
Electronics Enclosure, Installing . . . . . . . . . . . . . . . . . . . . . . 5 Read Reynolds KFactor Table . . . . . . . . . . . . . . . . . . . .151
Enter / Exit Fixed Loop Current . . . . . . . . . . . . . . . . . . . . 119 Read Sensor Meter Setup. . . . . . . . . . . . . . . . . . . . . . . .137
Enter Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Read Signal Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156

Index
Read Transducer Information . . . . . . . . . . . . . . . . . . . 138 M

Read Transducer Traverses and Spacing. . . . . . . . . 140 Main Menu
Read Velocity KFactor Table . . . . . . . . . . . . . . . . . . . . 150 Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Reset Flow Meter Data . . . . . . . . . . . . . . . . . . . . . . . . . 162 Measurement Type for Digital Output, Setting . . . . . . . 52
Reset to Factory Setting . . . . . . . . . . . . . . . . . . . . . . . . 165 Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Sends new password . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Meter Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Set Analog Measurement Range Values . . . . . . . . . 123 Meter Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Set Loop Current Error Handling . . . . . . . . . . . . . . . . 124 MODBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62, 97
Set Loop Current Gain . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Baud Rate, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Set Loop Current Percentage . . . . . . . . . . . . . . . . . . . 122 Modbus
Set Loop Current Zero . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Address, Selecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Test Digital Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Modbus Bits/Parity, Selecting . . . . . . . . . . . . . . . . . . . . . . . 63
Write Alarm Configuration. . . . . . . . . . . . . . . . . . . . . . 133 MODBUS Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Write Calibration Configuration. . . . . . . . . . . . . . . . . 152 MODBUS Stop Bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Write Density Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Modbus/Service Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Write Digital Configuration . . . . . . . . . . . . . . . . . . . . . 129
Write Display Backlight . . . . . . . . . . . . . . . . . . . . . . . . . 117 O
Write Error Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 One or Two-Variable Screens, Changing . . . . . . . . . . . . . 33
Write Factory Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . 164 One- or Two-Variable Screens, Measurement Type . . 34
Write Fluid Information. . . . . . . . . . . . . . . . . . . . . . . . . 148
P
Write Pipe Lining Attribute . . . . . . . . . . . . . . . . . . . . . 143
Write Pipe Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Write Pipe Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Pipe Lining, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Write Pulse Configuration . . . . . . . . . . . . . . . . . 130, 131 Pipe Material, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 71, 72
Write Reynolds KFactor Table. . . . . . . . . . . . . . . . . . . 154 Pipe OD/ID/Wall Thickness. . . . . . . . . . . . . . . . . . . . . . . . . . 70
Write Sensor Meter Setup . . . . . . . . . . . . . . . . . . . . . . 144 Pipe Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Write Transducer Information . . . . . . . . . . . . . . . . . . 145 Pipe, Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Write Transducer Traverses and Spacing . . . . . . . . 147 Program Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Write Unit Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Program Review Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Write Velocity KFactor Table . . . . . . . . . . . . . . . . . . . . 153 Publication Date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
HART Engineering Units . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Pulse Error Handling, Setting. . . . . . . . . . . . . . . . . . . . . . . . 55
Pulse Output, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
I Pulse Setting, Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Pulse Time, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Pulse Value, Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
K
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 R
Keypad Lockout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Read Alarm Configuration . . . . . . . . . . . . . . . . . . . . . . . . .128
Read Analog Measurement Range Values . . . . . . . . . .117
L
Read Backlight Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Language, Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Read Calibration Configuration . . . . . . . . . . . . . . . . . . . .149
Left Arrow Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Read Current User Access Right. . . . . . . . . . . . . . . . . . . .110
Login with password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Read Density Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Logout and save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Read Digital Configuration . . . . . . . . . . . . . . . . . . . . . . . . .125
Logout without saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Read Error Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Read Flowmeter S/N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157

Index
Read Flowmeter Version . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Read Fluid Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Totalizer
Read Frequency Configuration . . . . . . . . . . . . . . . . . . . . 127 Resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Read Loop Current Error Handling. . . . . . . . . . . . . . . . . 118 Totalizer Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Read Pipe Lining Attribute . . . . . . . . . . . . . . . . . . . . . . . . 136 Totalizer Programming
Read Pipe Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Decimal Places . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Read Pipe Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Pulse Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Read Pulse Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 126 Totalizer Screens, Changing Measurement or Value . 35
Read Reynolds KFactor Table. . . . . . . . . . . . . . . . . . . . . . 151 Transducer Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Read Sensor Meter Setup . . . . . . . . . . . . . . . . . . . . . . . . . 137 Transducer Spacing, Programming . . . . . . . . . . . . . . . . . . 86
Read Signal Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Transducer, Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Read the Factory Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Transit-Time Flow Measurement . . . . . . . . . . . . . . . . . . . . . 2
Read Transducer Information . . . . . . . . . . . . . . . . . . . . . 138 Traverses, Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Read Transducer Traverses and Spacing . . . . . . . . . . . 140 Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . vii
Read Velocity KFactor Table . . . . . . . . . . . . . . . . . . . . . . . 150
U
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Reset Flow Meter Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Units Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Reset to Factory Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Universal Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Revision Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i Up Arrow Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Right Arrow Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 User Preferences
RoHS Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
S Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Safety Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Auxiliary Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii Units Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
General Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
W
Personal Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Safety Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Sends new password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 WEEE Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Sensor Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Write Alarm Configuration . . . . . . . . . . . . . . . . . . . . . . . . .133
Set Analog Measurement Range Values . . . . . . . . . . . 123 Write Calibration Configuration . . . . . . . . . . . . . . . . . . . .152
Set Loop Current Error Handling . . . . . . . . . . . . . . . . . . 124 Write Density Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Set Loop Current Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Write Digital Configuration . . . . . . . . . . . . . . . . . . . . . . . .129
Set Loop Current Percentage. . . . . . . . . . . . . . . . . . . . . . 122 Write Display Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Set Loop Current Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Write Error Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Write Fluid Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Special Transducer, Setting. . . . . . . . . . . . . . . . . . . . . . . . . .77 Write Frequency Configuration
Starting or Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 HART Commands
Write Frequency Configuration131, 132
T Write Pipe Lining Attribute. . . . . . . . . . . . . . . . . . . . . . . . .143
Terms and Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Write Pipe Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
Test Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Write Pipe Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
Test Digital Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Write Pulse Configuration . . . . . . . . . . . . . . . . . . . .130, 131
Test Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Write Reynolds KFactor Table . . . . . . . . . . . . . . . . . . . . . .154
Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Write Sensor Meter Setup . . . . . . . . . . . . . . . . . . . . . . . . .144

Index
Write the Factory Setting . . . . . . . . . . . . . . . . . . . . . . . . . 164

Write Transducer Information . . . . . . . . . . . . . . . . . . . . . 145
Write Transducer Traverses and Spacing . . . . . . . . . . 147
Write Unit Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Write Velocity KFactor Table . . . . . . . . . . . . . . . . . . . . . . 153
Z
Zero Cutoff, Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

GE EU DECLARATION
Sensing OF
CONFORMITY
DOC-0050 Rev. A
We,
GE Sensing
1100 Technology Park Drive
Billerica, MA 01821
USA
declare under our sole responsibility that the
AquaTrans™ AT600 Ultrasonic Flowmeter for Liquids
to which this declaration relates, is in conformity with the following standards:
• EN 61326-1: 2013, Class A, Group 1, Industrial Locations

• EN 60529: 1991+A1:2000+A2: 2013 IP67
• EN 61010-1: 2010
following the provisions of Directives 2014/30/EU EMC and 2014/35/EU LVD.
16 June 2016
Issued Mr. Chris Frail
Engineering Manager
GE Measurement Solutions
Billerica, MA U.S.A.
GE Certification &
Measurement & Control Safety Statements
Certification & Safety Statements for GE Measurement & Control Ultrasonic Flow Transmitters
When installing this apparatus, the following requirements must be met:
• Field wiring shall be rated at least 10°C above 70°C.
• Connecting cables shall be mounted securely and protected from mechanical damage, pulling and twisting.
• Cable entries are ¾” NPT.
• Cable glands of an approved flameproof design are required. These must be installed according to the manufacturer’s
instructions. Where the cable glands are provided by GE, the manufacturer’s instructions, as supplied, to GE, will be
included in the documentation.
• Unused cable entries must be sealed using a certified threaded plug.
• Modifications to the flameproof enclosure are not permitted.
• The apparatus should be de-energized before opening.
• Installation should comply with IEC/EN 60079-14.
• Equipment is of type flameproof “d” design and complies with: EN 60079-0:2009, EN 60079-1:2007,
EN 60529:1991 +A1:2000, IEC 60079-0:2011, IEC 60079-1:2007, IEC 60529:2001.
• The product contains no exposed parts which produce surface temperature infrared, electromagnetic ionizing, or
non-electrical dangers.
• The product must not be subjected to mechanical or thermal stresses in excess of those permitted in the certification
documentation and the instruction manual.
• The product cannot be repaired by the user; it must be replaced by an equivalent certified product. Repairs should only
be carried out by the manufacturer or by an approved repairer.
• Only trained, competent personnel may install, operate and maintain the equipment
• The product is an electrical apparatus and must be installed in the hazardous area in accordance with the requirements
of the EC Type Examination Certificate. The installation must be carried out in accordance with all the appropriate
international, national and local standard codes and practices and site regulations for flameproof apparatus and in
accordance with the instructions contained in the manual. Access to the circuitry must not be made during operation.
Special Conditions for Safe Use: Consult the manufacturer if dimensional information on the flameproof joints is
necessary.
Markings: Markings shall appear on the product as shown below:
CL I, DIV. 1, GPS BCD; T6. GE INFRASTRUCTURE SENSING

FM
C US
APPROVED CL I, ZONE 1, AEx/Exd IIB + H2 1100 TECHNOLOGY PARK DR.
BILLERICA MA USA
II 2 G Ex d IIB + H2 T6 Gb IP66
IECEx FMG12.0012X
FM12ATEX0040X MODEL: XXXXXXX
S/N: XXXXXXXX
Tamb = -20°C to +60°C MFG DATE: MMXXYY
CABLE GLAND ENTRIES ARE 3/4" NPT
SUPPLY CONNECTION WIRING SHALL BE RATED VOLTAGE: XXX
1180 WATTS: XXX
AT LEAST 10°C ABOVE 70°C.
WARNING - DO NOT OPEN WHEN ENERGIZED
AVERTISSEMENT - Ne pas ouvrir sous tension
WARNING - DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE IS PRESENT
AVERTISSEMENT - Ne pas ouvrir une atmosphere eplosive gazeuse est presente
1100 Technology Park Drive, Billerica, MA 01821, U.S.A. CSS-0001, Rev. A

Telephone: 978-437-1000 or 800-833-9438 June 2012
Sensing House, Shannon Free Zone East, Shannon, County Clare, Ireland
Telephone: +353 61 470200
Customer Support Centers
U.S.A.
The Boston Center
1100 Technology Park Drive
Billerica, MA 01821
U.S.A.
Tel: 800 833 9438 (toll-free)
978 437 1000
E-mail: mstechsupport@bhge.com
Ireland
Sensing House
Shannon Free Zone East
Shannon, County Clare
Ireland
Tel: +353 61 61470200
E-mail: mstechsupport@bhge.com
bhge.com
© 2017 Baker Hughes, a GE company – All rights reserved.
Baker Hughes reserves the right to make changes in specifications and features shown herein, or discontinue the product
described at any time without notice or obligation. Contact your BHGE representative for the most current information. The
Baker Hughes logo is a trade mark of Baker Hughes, a GE company. The GE Monogram is a trademark of the General Electric
Company.
910-312 Rev. D

AT600 Manual

Uploaded by

Copyright:

Available Formats

AT600 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AT600 Manual

Uploaded by

Copyright:

Available Formats

Flow

bhge.com 910-312 Rev. D

Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

AquaTrans™ AT600 User’s Manual iii

4.3.1 Changing the Display for One- or Two-Variable Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

iv AquaTrans™ AT600 User’s Manual

AquaTrans™ AT600 User’s Manual v

D.6 The Main Menu > Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192

[no content intended for this page]

vi AquaTrans™ AT600 User’s Manual

Terms and Conditions

AquaTrans™ AT600 User’s Manual vii

Personal Safety Equipment

viii AquaTrans™ AT600 User’s Manual

Waste Electrical and Electronic Equipment (WEEE) Directive

Please visit http://www.gemeasurement.com/environmental-health-safety-ehs for take-back instructions and

AquaTrans™ AT600 User’s Manual ix

[no content intended for this page]

x AquaTrans™ AT600 User’s Manual

Chapter 1. General Installation Instructions

• So easy to use, it practically installs itself

Strap With Transducer Installed

Figure 1: Typical AT600 System Mounted on a Pipe

AquaTrans™ AT600 User’s Manual 1

1.2 Theory of Operation

Figure 2: Flow and Transducer Paths (Two Traverses)

Figure 3: Flow and Transducer Paths (One Traverse)

2 AquaTrans™ AT600 User’s Manual

1.3 Safety Guidelines

• “Installing the Electronics Enclosure” on page 5

• “Choosing a Clamp-On Fixture/Transducer Location” on page 7

• “Mounting the Clamp-on Fixture and Transducer System” on page 8

AquaTrans™ AT600 User’s Manual 3

1.4 Unpacking the AT600 system

Figure 4: Typical AT600 Shipping Container

4 AquaTrans™ AT600 User’s Manual

1.5 Installing the Electronics Enclosure

Weight is about 1.5 kg

AquaTrans™ AT600 User’s Manual 5

1.5 Installing the Electronics Enclosure (cont.)

Figure 6: The AT600 Mounting Base

1.6 Calculating the Transducer Spacing

6 AquaTrans™ AT600 User’s Manual

1.7 Choosing a Clamp-On Fixture/Transducer Location

Figure 7: AT600 Clamp-On Fixture/Transducer Location

AquaTrans™ AT600 User’s Manual 7

1.8 Mounting the Clamp-on Fixture and Transducer System

Table 1: Available Transducers

UTXDR1 4 MHz SPCF 0.5-8 in. (15-200 mm)

C-RS2 1, 0.5 MHz GCF 2 in. (50 mm)

C-PT2 2, 1, 0.5 MHz GCF 2 in. (50 mm)

Table 2: AT600 Clamp-On Fixture Installation

8 AquaTrans™ AT600 User’s Manual

1.8 Mounting the Clamp-on Fixture and Transducer System (cont.)

• Calculated Transducer Spacing

• Number of Clamp-On Fixtures

• “Transducer Spacing = 320 to 940 mm, Traverses = 2, Fixtures = 2” on page 14

• “Transducer Spacing = 0 to 250 mm or 0 to 320 mm, Traverses = 1, Fixtures = 2” on page 17

• “Transducer Spacing >320 mm, Traverses = 1, Fixtures = 2” on page 19

AquaTrans™ AT600 User’s Manual 9