TLE Carpentry LP 3rdQ

K-12 Basic Education Curriculum
Technology Livelihood Education

Carpentry (exploratory Course Grade 7 and 8)
Date: November 18-21 , 2019 8-Sampaguita/1:45pm-2:45pm

I. Objectives: In the end of the lesson the students would be able to;
Identify and classify tools and equipment
II. Subject Matter
Topic : Tools and equipment
Reference: page 28-30, k-12 BEC – TLE, Carpentry Grade 7
Materials: Visual Aids, Hand outs
III. Procedures
1. Preliminary Activities
a. Prayer
b. Attendance
2. Awareness
The teacher will facilitate pictures of the
Motivation
The teacher will ask the students;
who have seen renovating a building?
what is used to make building?
And so on the students would be aware that we will identify the tools and equipment.
Activity
The Students will classify the different types of tools
1. Claw Hammer
2. Bar Clamp
3. Spoke Shave
4. Steel Square
5. Back Saw
6. Pull Push Rule
7. Compass
8. Triangular
9. Varnish
10.Hinge
Analysis
The teacher will ask the students, what if there are no tools and equipment, Is there a school,
houses and other establishments?
Presentation
The teacher will facilitate a picture of hand tools and together with the student will discuss,
identify and classify of the tools and equipment like;
CLASSIFICATION OF HANDTOOLS
MEASURING TOOLS:
Pull – Push Rule Ruler Meter Stick

A. Measuring tools
1. Pull-Push Rule - flexible tape that slides into a material case and it is used to
measure irregular and regular shapes.
2. Ruler - 12-inch or one foot rule and it is used to take/make simple
measurements.
3. Meter Stick - used to measure a work piece.
4. Try Square - squaring, measuring and testing tool used to check adjacent
surfaces for squareness.
5. Caliper - used to transfer measurements from the rule to the work.
B. MARKING LINING TOOLS
1. Pencil - used to layout or mark cutting lines.
2. Marking Gauge - wood or metal tool consisting of a beam, head and a point
used to mark a line parallel to the grain of the wood.
3. Chalk Line - used to establish a straight line on a surface.
4. Divider - tool with two metal legs used to lay-out an arc circle or step
off division on a line.
5. Compass - used to scribe arcs and circle in a metal wood.
C. TESTING TOOLS
1. Try Square - tool used in squaring, measuring and testing the squareness
of a wood.
2. Steel Square - framing square used to mark out the work for squaring and
checking of angles and is used in the construction of roof
framing and large furniture.
3. Spirit Level - tool used for testing vertical and horizontal surfaces.
4. Plumb bob - tool used to test the vertical and horizontal surfaces.
D. EDGE CUTTING TOOLS
1. Chisel - tool used to trim and shape wood.
2. Plane - used to obtain a smooth and flat surface.
3. Spoke shave - small plane like tool from irregularly shaped objects.
4. Cabinet scraper - rectangular piece of steel with two cutting edges used for
working flat and curved shapes.
E. TOOTH-CUTTING TOOLS
1. Cross Cut Saw - handsaw used to cut the wood across the grain.
2. Rip-saw - hand saw used to cut the wood along the grain.
3. Back Saw - handsaw with a metal back and plywood and joinery.
4. Compass Saw - used to cut irregular shape either in large or small board.
5. Turning Saw - used to rip, cross and cut curves in lumber.
6. Coping Saw - u-shaped saw used for cutting irregular shape in small board.
7. Dovetail Saw - small back saw with a straight chisel type handle used to cut
very fine joints.
F. BORING TOOLS
1. Auger bit - tool used to make hole in woods.
2. Expansive bit - tool used to drill holes of various sizes in woods.
3. Drill Bit - tool used for boring holes either in metals, woods or plastics.
G. HOLDING TOOLS
1. C-Clamp - used for holding together pieces of lumber while working.
2. Bench Vise - used to hold any materials or tools in place.
3. Bar Clamp - used to hold large boards or frames together while
assembling or gluing.
H. MISCELLANEOUS TOOLS
1. Oil Stone - used for sharpening edge cutting tools such as chisel.
2. Files - used to smoothen metal and wood surfaces.
3. Paint Brush - used to apply paint or varnish on wood surfaces
4. Nail Set - used to drive the head of nails lower than surface of wood.
5. Saw Set - used to bend the upper half of each tooth to one side or the
other to form a set.
I. PORTABLE POWERTOOLS
1. Sander - portable power tool used for sanding furniture pieces.
2. Router - used for shaping surfaces and edges of furniture parts.
3. Jigsaw - power tool used primarily for cutting curved or irregular
shapes of wood surfaces.
4. Circular saw - power saw used for many types of cutting, particularly on
large panel stock.
5. Electric Drill - power drill which is used to drill holes in various materials to
perform a multitude of tasks.
J. PPE (Personal Protective Equipment)
1. Goggles - used to protect the eyes against flying debris and harmful
liquids.
2. Ear Protector - used to protect the ears against high frequency noise.
3. Face Mask - used to prevent the inhalation of sprayed paint fumes.
4. Gloves - used to protect the hands while working.
5. Apron - used to protect the worker against flying debris.
K. DRIVING TOOLS
1. Claw Hammer - used to drive and pull out nails on wooden surfaces.
2. Mallet - made out of wood or rubber used to drive other tools like
chisel.
3. Nail Set - used in setting the head of a finishing nail below the surface
of the wood.
4. Screw Driver - used to drive and loose screws.
IV. Applcation
Identify the different tools that are describe in each item.
1. Tool used for smoothing curve surfaces.
2. Finishing materials used to seal the pores of wood.
3. Tool used for drawing arcs and circles.
4. Tool used for testing the squareness of large stocks.
5. Tool used to hold bits when boring.
6. Finishing material which makes wood shiny.
7. Tool used to cut stock along the grain.
8. Tool used for sharpening saws.
V. Assessment
MATCHING TYPE
Choose letter and word for the answer. a) Chalk line
1. Used to establish a straight line on a surface. b) Nail set
2. Used to drive the head of nails lower than surface of wood. c) Mallet
3. Made out of wood or rubber used to drive d) Try square
4. other tools like chisel. e) Pencil
5. Squaring, measuring and testing tool f) Ear protector
6. used to check adjacent surfaces for squareness. g) Bar clamp
7. Used to layout or mark cutting lines. h) Router
8. Used to protect the ears against high frequency i) Jigsaw
noise. j) Goggles
9. Used to hold large boards or frames together while k) Compass
10. Used for shaping surfaces and edges of furniture parts.
11. Power tool used primarily for cutting curved or irregular
shapes of wood surfaces.
12. Used to protect the eyes against flying debris and harmful
liquids.
VI. Assignment
Draw tools and give example of tools that where to apply.
C. TESTING TOOLS
D. EDGE CUTTING TOOLS
E. TOOTH-CUTTING TOOLS
Ex
Pulll – Push Rule
used to measure irregular and regular shapes.
Prepared by: Checked by: Noted by:
Jennifer C. Macas Mr.Wilfrido S. Serna Dr. Christine Y. Guinacaran

Teacher I TLE Coordinator School Principal I

TLE Carpentry LP 3rdQ

Uploaded by

Copyright:

Available Formats

TLE Carpentry LP 3rdQ

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TLE Carpentry LP 3rdQ

Uploaded by

Copyright:

Available Formats

K-12 Basic Education Curriculum

Technology Livelihood Education

Date: November 18-21 , 2019 8-Sampaguita/1:45pm-2:45pm

Pull – Push Rule Ruler Meter Stick

used to measure irregular and regular shapes.

Prepared by: Checked by: Noted by:

Jennifer C. Macas Mr.Wilfrido S. Serna Dr. Christine Y. Guinacaran

You might also like