M5 Pro

Outdoor Fingerprint & Card

Reader/Controller

Quick Guide V1.1

Package List

M5 Pro
户外指纹&RFID卡门禁一体机

快速指南 V1.0

©2018 安威士 ● 中国
了解更多信息，请访问 www.anvizchina@anviz.com，或发送电子邮箱 info.asia@anviz.com 获取更多帮助。

Device Screws RJ45 Connector USB Quick Guide

Note:
1. Please check if the package contains all the
items listed above. Contact the distributor
M5 Pro
Outdoor Fingerprint & Card if there is any problem.
2. Please keep the product away from the
Reader/Controller

X4
magnetic field, and avoid causing any
ID Card CD damage to the device.
3. Please use the original power supply or
refer to the instruction to get the right
power supply.
4. Please strictly follow the instructions to
There are 4 cards in the package: install the product. Any damage to it
Enroll Card Delete Card User Card * 2. caused by incorrect operation and wiring
are not under warranty.

1
Illustration for placing finger
Correct method ( Straighten your finger and then place it on the sensor. Ensure the finger is flat and covers
the entire sensor window)

Always place finger in Try to place your finger covers the entire sensor window.
the center of the sensor.

Incorrect method

DO NOT move your finger before DO NOT place finger away from DO NOT place finger
the backlight of sensor turns off. the center of the sensor window. at an angle.

DO NOT take off finger during DO NOT just use your fingertip. DO NOT slide your finger
the fingerprint verification during the fingerpint
process. verification process.
2
Installation Diagram

Back panel install way: Without back panel install way:

Step2 Steps: Steps:

Step1
Step1: Drill holes in the wall
Fix M5 screws directly to the bottom
follow the hole position on
shell behind the wall, the depth of
back panel.
1.42in.(36mm) screws is 8mm. This install method is
unique, safe and convenient. Package
Step2: Install and fix back
list has no these screws, according to
panel, connect related cables. 2.52in.(64mm)

wall thickness select the length of M5

screws.
Step3: Place M5 Pro on back
0.41in.(10.5mm)

panel, fix screw at the bottom

Step3 of M5 Pro.

Appearance
Indicator LED
Three colour: Red,
Blue and Green.
Fingerprint Sensor
Place the finger here.

Card Reader Area Mini USB Port

Swipe the card here.
Function Button

Restart button Screw Hole

3
Wiring Instruction

DC12V
Connect RJ45 GND
Tamper alarm
Tamper alarm
Wiegand DATA0 Output
Wiegand DATA1 Output
D/S
Black GND
Black GND

RS485A
RS485B
NO
COM
NC

Anviz Wiegand Wiring:

SC011 and the device are paired by
Anviz wiegand to be a distributed access
Switch Power Supply control system.

+12V

Power off to unlock

+12V

Power on to unlock
Exit Button 4
SC011 authorization setting:
Make sure correct wiring between M5 Pro and SC011, power on them, then move slide switch to
‘PROGRAM MODE’ as below:
Switch in‘PROGRAM’on the SC011: Move slide swith to left(ON).

Match registered fingerprint or swipe

Power On： registered card on M5 Pro, then SC011 will
Authorization Red Light beep once, means authorized successfully.
Mode Then move slide switch to right(OFF).

Wiegand 26 Wiring:
Between M5 Pro and Anviz SAC844 or other Access Controller as below:

Wiegand data output format:

1. Anviz Wiegand data output format:
ALL registered users output devieces’ last eight serial number.(For example, SN of one device
is 1050000014470004, then Anviz Wiegand output 14470004.)
2. Wiegand 26 data output format:
Card user: Output card number.(Decimal)
Fingerprint user: Output ID number
3. Wiegand output format can be set by PC software

4
5
Wiring Type Access Controller

Switch Power
Supply

Power off to unlock

Power on to unlock

Switching Power Supply

Switch Power
Supply
Power off to unlock

Power on to unlock

Important notice:
Please carefully follow this wiring instruction. Any damage caused by incorrect wiring is not covered by warranty.

6
Working with Management Software
1. Install the Management Software on Computer
Put the CD in the managemet computer. The installation program will run automatically.

How to connect M5 Pro with Software?

1st Method: Mini USB
Loose the screw on the bottom of M5 Pro,
then pull up the front case, seperate from
back panel.
Connect USB cable between M5 Pro and
PC which has installed software.

Pay Attention:
If management cards are registered,
indicator light turns yellow and flashes. You
must verify any management card first. If no
management card is registered, you can
communicate with M5 Pro directly.
7
2st Method: Mini USB

Local Area Network (TCP/IP)

Right click on the device icon

and choose ‘Set the IP configuration’
to set correct network enviroment
parameters such as above window.

2. Enable Communication between M5 Pro and the Management Software CrossChex

*Turn on management software CrossChex

*Go to Device tab. Search and add the M5 Pro to management software CrossChex
*Click Synchronize Time button to communicate with M5 Pro. If Synchronize is
successful, the device icon will turn to blue.

3. The Management Software CrossChex Features

*Device\Backup User: Download user info from M5 Pro to CrossChex

*Device\Download Records: Download records from M5 Pro to CrossChex
*User\Modify: Edit name or other user info. Then click “Upload User”to Upload
user info to M5 device
8
 *Record\Search: search and view the records
*Attendance: Calculate, Search results and generate reports
*Data\Backup Database: Backup Database
*Setting\Shift: Set up Time table and Scheduling
*Device\Device Parameter: Set up device, Clear records on M5 Pro or Reset M5 Pro to
factory settings

Function Button

9
Operation Guide
IMPORTANT:
M5 Pro is suitable for DC12V power supply only. When connect to DC12V power supply, the indicator light displays
blue and flashes fast. Meanwhile, the backlights of fingerprint sensor turn on with beeps.

Register User:
Add One Fingerprint per User Only:
Note: 1. After finish enrolling current user, 5. Continue to register another user
please swipe enroll card and then continue
register another user. 2. Place finger 3. Place finger 4. Swipe Enroll Exit
again Card once1 Enrollment
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.
1. Swipe
Notice: Enroll Card 6. Swipe Enroll
When you place finger on M5 Pro, Red LED Blue LED Blue LED flashes fast Green LED lights up Card TWICE to end
flashing with two long beeps means the finger has flashes and fingerprint with 4 short beeps, the enrollment2
been registered. sensor lights up registration successed

Add Card Only:

Note: 1. After finish enrolling current user, 5. Continue to register another user
please swipe enroll card and then continue
register another user.
2. Swipe 3. Swipe User 4. Swipe Enroll Exit
User Card Card again Card once1 Enrollment
2. After finish enrollment, please swipe
enroll card TWICE to exit enroll status.
1. Swipe
Enroll Card 6. Swipe Enroll Card
Notice: TWICE to end the
Blue LED Blue LED flashes Green LED lights up
When you swipe card on M5 Pro, Red LED enrollment2
flashes fast and with 4 short beeps,
flashing with two long beeps means the card has FingerPrint registration
been registered. sensor lights up successed

10
Operation Guide

Add Two Fingerprints of one User: 8. Continue to register another user

* Two fingerprints belongs to one user ID.
4. Continue to register the 2nd finger
Note: 1. After finish enrolling current user, 2/5. Place the 3/6. Place the 1st/2nd 7. Swipe Enroll
please swipe enroll card and then continue 1st/2nd finger finger again Card once1 Exit
register another user. Enrollment

2. After finish enrollment, please swipe

enroll card TWICE to exit enroll status. 1. Swipe
Enroll Card 9. Swipe Enroll
Card TWICE to
Blue LED Blue LED flashes fast Green LED lights up end the
flashes and FingerPrint with 4 short beeps, enrollment2
sensor lights up registration
successed

Add Fingerprint and Card of one User:

* The wiegand output of fingerprint and card are the same.

8. Continue to register another user

2. Place finger 3. Place finger 4. Swipe 5. Swipe User 7. Swipe Enroll Exit
again User Card Card again Card once1 Enrollment

1. Swipe 9. Swipe Enroll Card

Enroll Card TWICE to end the
Blue LED Blue LED Green LED lights up Blue LED Green LED lights up enrollment2
flashes flashes fast and with 4 short beeps, flashes fast and with 4 short beeps,
FingerPrint registration FingerPrint registration
sensor lights up successed sensor lights up successed

Note:
1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

11
Operation Guide

Add Two Fingerprints and Card of one User:

* The wiegand output of fingerprint and card are the same.
10. Continue to register another user
Note: 1. After finish
enrolling current user,
please swipe enroll card 4. Continue to register the 2nd finger
and then continue register
another user. 2/5. Place finger 3/6. Place finger 7. Swipe 8. Swipe User 9. Swipe
again User Card Card again Enroll Card Exit
2. After finish once1 Enrollment
enrollment, please
swipe enroll card
TWICE to exit enroll
status. 1. Swipe 11. Swipe
Enroll Card Blue LED Enroll Card
Blue LED Green LED lights up Blue LED Green LED lights up
flashes flashes fast and with 4 short beeps, flashes fast and with 4 short beeps, TWICE to end
FingerPrint registration FingerPrint registration the
sensor lights up successed sensor lights up successed enrollment2

Delete User:
Delete Fingerprint or Fingerprint and Card
After delete one user, you can continue to delete 4. Continue to delete
another user or swipe Delete Card to save and exit.
2. Place finger 3. Place finger
When fingerprints or card belong to one user again
ID, you can delete either one to delete this 5. Swipe Delete
user. Card to end
the process
1. Swipe
Notice: Delete Card
When you place finger on M5 Pro, Red LED Red LED Red LED flashes Green LED lights up
flashing with long beeps means the fingerprint flashes fast and with 4 short beeps,
does not exist in the device.
FingerPrint fingerprint deleted
sensor lights up

12
Operation Guide

Delete Card:

After delete one user, you can continue delete another 4. Continue to delete
user or swipe Delete Card to save and exit.
2. Swipe 3. Swipe User
User Card Card again
5. Swipe Delete
Card to end
the process
1. Swipe
Delete Card
Red LED Red LED flashes Green LED lights up
Notice: flashes fast and with 4 short beeps,
When you swipe card on M5 Pro, Red LED FingerPrint card deleted
flashing with long beeps means the card does sensor lights up
not exist in the device.

Delete All Users

Delete all uses fingerprints and cards, the

device parameter setting do not change.
2. Swipe 3. Swipe Enroll
Enroll Card Card again

4. Swipe Delete
Card to end
the process
1. Swipe
Delete Card
Red LED flashes Red LED flashes fast Green LED lights up
4 short beeps
Delete ASuccessed

Anviz brand and product are trademarked and protected under law of the United States.
Unauthorized use is prohibited.
For more information, please visit www.anviz.com, or send email to sales@anviz.com for more help.
©2018 Anviz Global Inc. All Rights Reserved. 13
201809