4.

Attach the Main Unit to the back cover - ensure the locks snap
closed.
NV37MR
5. Insert two AA batteries.
Installation Manual
6. Set the following Detector settings according to requirements.
Wireless Outdoor/Indoor Window
and Sliding Door Dual Detector with Sensitivity Trimmer DIP
Anti-Masking and Pet Immunity Switches

General Description NV37MR

Thank you for choosing the NV37MR Wireless for your professional
protection needs. The NV37MR wireless version will provide you the Default Sensitivity level: 2
most advanced window and sliding doors protection either in Pet LED flashes green 1-3 times
Immune or Sharp mode. If you have any comments please write to us according to the selected level.
at Paradox.com/products/feedback.
Recommended Installations (please read)
Outdoor installation permits placements within frames of sliding Figure 4 – Detector Settings
windows or doors and presumes protection from raindrops. This
ensures best catch performance, anti-masking ability, and pet alarm
immunity. The following table displays the Dip Switch settings.
Other installations are possible but in outdoor conditions, pet immunity
can decrease. Moreover, space near the detector must be clear from Table 1: DIP Switch Functionality
obstacles from a distance of 30 to 40 cm (11.8 to 15.7 in.) within its
pattern. Dip Switch
Function Mode Description
Number
Installing the NV37MR
1. Remove the front cover - open the Captive screw. 1 LED ON: LED on (default)
OFF: LED off
Knockout 2 PET Immunity/ ON: PET Immunity mode (default)
holes SHARP Mode OFF: SHARP mode
Front
Mounting
3 For future use
cover screw
4 Anti-mask ON: On (default)
Tamper
knockout OFF: Off
hole
Tamper 5 Anti-mask ON: High (default)
screw Sensitivity OFF: Low

Captive screw
7. Close the front cover and tighten the captive screw.
Figure 1 – Front Cover Figure 2 – Main Figure 3 – Back Plate
Unit
Note: Do not obscure the detector's field of view.
2. Remove the Main Unit: open the two snap-lock mechanisms on Note: On MG/SP panels, the anti-masking is reported as a tamper.
each side of the back cover attaching the Main Unit to the back Tamper recognition must be enabled in panel programming.
cover, then remove the Main Unit. On EVO panels, it is reported as anti-masking if it is enabled in
3. Mount the back cover of the NV37MR onto the window frame or the panel programming.
wall using screws.
Note: PLEASE KEEP AT LEAST 4 cm / 1.5 in. clearance from
window/shutter. Testing the NV37MR
Perform a Walk-Test to test successful installation:
4 cm /
1.5 in. 1. Walk slowly across the far end of the detection range.
2. Ensure detection.

Walk test mode lasts 5 minutes after the tamper screw is closed.

Learning the NV37MR

For more information on configuring the NV37MR via the panel, refer
An optional mounting bracket for the NV37MR is available for to the panel’s respective programming guide.
ordering, part number: SB35.
1. Enter the appropriate section number.
2. To learn the module, loosen the captive screw until the tamper is
open. After the module is learned, tighten back the captive screw.

NV37MR-EI00 03/2022 PARADOX.COM

Beam Pattern Technical Specifications

PET Mode Model Number NV37MR

Infrared sensor type 2 dual elements
Detection range • PET Immunity mode: 7.5m x 2m
(25 x 7 ft)
• Sharp mode: 10 x 2m (33 x 7 ft)
Super Pet Immunity Pet size approximately 50 cm
Anti-mask Active IR detection of blocking objects
and liquids sprayed on the detector from a
distance of up to 7.5 cm.
Input voltage 3VDC=2 x1.5VDC AA Alkaline batteries
Current consumption 40µA in Standby
SHARP Mode 30mA in Alarm/RF Transmitting
Battery life 3 years of typical use
SIDE VIEW:
Low battery voltage 2.35V
2m
(6.5ft) Signal
1.5m Compatibility RTX3 and Magellan systems
1m Outdoor protection IP54
0.5m
Operation -40°c to +70°c
0m
temperature
0m 1m 2m 3m 4m 5m 6m 7m 8m 9m 10m
(32.8ft) Relative humidity 95% non-condensing
Tamper* Dual - Cover and Wall
Top View RF Frequency 433.92 MHz or 868.35 MHz
Dimensions 12.3 x 6.1 x 4.3 cm (4.8 x 2.4 x 1.7 in.)
Weight 100g / 0.2 lb
Certifications CE, EN50131-2-2 Grade 2, Class IVA
EN 50131-6 Type C
Certification Body: Applica Test &
Certification
Note: EN performance tests were
conducted on sensitivity level 3 (high).

LED Display * Tamper recognition must be enabled on panel programming.

Feature LED Status Indicator

Tamper open Green: ON for 0.3 seconds every 30
seconds
PIR sensitivity level setting Green: Flashes 1-3 times according
to the selected level
Alarm detection Red: ON for 2 seconds
Power Save mode: Red blinks
Booting/Tamper close Green/Red alternating flashes for 30
seconds
Anti-mask detection Flashing Orange:
Pre-mask situation is detected.
Orange LED flashes ON/OFF 3
times, every 30 seconds, for as long
as anti-mask is detected.

Warranty
For complete warranty information on this product, please
refer to the Limited Warranty Statement found on the
website: www.paradox.com/terms or contact your local
distributor. Specifications may change without prior notice.

Patents
US, Canadian and international patents may apply.
Paradox is a trademark or registered trademark of Paradox
Security Systems (Bahamas) Ltd.

NV37MR-EI00 03/2022 PARADOX.COM