NV35M 4. Attach the Main Unit to the back cover - ensure the locks snap closed.

Installation Manual v1.0

Outdoor/Indoor
Window and Sliding Door
Dual Detector with
Anti-Masking and
Pet Immunity

1 2 3
NV35M-EI01

Figure 5 – Attaching the Main Unit

General Description
Thank you for choosing the NV35M for your professional protection needs. 5. Connect the wires to the terminal blocks according to the following
The NV35M wired version will provide you the most advanced window and wiring assignment.
sliding door protection either in Pet Immune or Sharp mode. If you have Table 1: Wiring Assignment
any comments please write to us at Paradox.Com/products/feedback. Terminal Connector Recommended Wiring Assignment
This guide describes how to install and program the NV35M.
1 12V+
Installing the NV35M 2 Minus (-)

1. Remove the NV35M front cover - open the Captive screw. 3 Fault indication
4 Tamper indication
Front cover
5 Common (Fault & Tamper)
6 Alarm indication
7 Common (Alarm)

6. Set the following Detector settings according to requirements.

Captive screw

Figure 1 – Removing the Figure 2 – Main Unit Sensitivity Trimmer

Front Cover

2. Remove the Main Unit: open the two snap-lock mechanisms on each
side of the back cover attaching the Main Unit to the back cover as Dip Switch
displayed below. Then remove the Main Unit.

LED flashes green 1-3 times

according to the selected
level

Figure 6 – Detector Settings

Figure 3 – Removing the Main Unit The following table displays the Dip Switch settings.
3. Pull the wires from the control panel through the knockout holes and Table 2: Dip Switch Settings
mount the back cover onto the window frame or wall using screws.
Dip Switch
Knockout Function Mode Description
Number
holes
Mounting ON: LED on (default)
1 LED
screw 1 OFF : LED off

PET Immunity/ ON: PET Immunity mode (default)

Tamper 2
SHARP Mode OFF : SHARP mode
knockout
hole
7. Replace the front cover and close the Captive screw.
Mounting
Tamper Warning: Do not obscure the detector's field of view.
screw 2

Figure 4 – Mounting the Back Cover

PARADOX.COM
Testing the NV35M LED Display
Perform a Walk-Test to test successful installation: Walk slowly across the Feature LED Status Indicator
far end of the detection range. Ensure detection.
Tamper open Green: ON for 0.3 seconds every 30
Walk test mode lasts 5 minutes after the tamper screw is closed.
seconds

Beam Pattern PIR sensitivity level setting Green: Flashes 1-3 times according to
the selected level
PET Mode Alarm detection Red: ON for 2 seconds
Booting/Tamper close Green/Red alternating flashes for 30
seconds
Anti-mask detection Orange: Flashes ON/OFF 3 times every
60 seconds

Technical Specifications

Specification Description
Infrared sensor type 2 Dual elements
Detection range • PET Immunity mode: 7.5m x 2m (25 x 7
ft)
• Sharp mode: 10 x 2m (33 x 7 ft)
Super Pet Immunity Pet size approximately 50cm
Anti- mask Active IR detection for blocking items 30cm
SHARP Mode
and sprayed liquid
Input voltage 10 to 15VDC
Current consumption Typical: 15mA
Maximum: 19.2mA
Compatibility EVO, Spectra and Magellan systems
Outdoor protection IP54
Operation temperature -35°c: +50°c
Relative humidity 95% non-condensing
Dimensions 12.3 x 6.1 x 4.3 cm (4.8 x 2.4 x 1.7 in.)
Certifications CE, EN50131-2-2 Grade 3, Class IV
Weight 100g / 0.2 lb
Top View
Notification
Changes or modifications to this equipment not expressly approved by the
party responsible for compliance (Paradox Security Systems Ltd.) could
void the user’s authority to operate the equipment.

Warranty
The Limited Warranty Statement found on the website www.paradox.com/
terms.
Your use of the Paradox product signifies your acceptance of these terms
and conditions.

Patents
The following US patents may apply 5,886,632 and 6,215,399, Other
Canadian and international patents may apply.

Printed in Canada 05/2015.

PARADOX.COM