Boerger Rotary Lobe Pump PDF

Planning Information
Börger Rotary Lobe Pumps

Börger Chopping Technology
07/06
BÖRGER GmbH
Benningsweg 24 46325 Borken-Weseke Telefon: +49 (0) 28 62 / 91 03-20
P.O.Box 3065. 46314 Borken-Weseke Telefax: +49 (0) 28 62 / 91 03-46
Germany
Internet: www.boerger-pumps.com e-mail: info@boerger.de
The Börger Rotary Lobe Pump Function and Features 1
Components
2
Performance Overview
3
AL Series
(Drawings, Dimensions, Performance Curves) 4
PL Series
CL Series
FL and FLA Series

XL Series
The Börger Chopping Technology The Börger Multicrusher

9
(Drawings and Dimensions)
The Börger Multichopper

10
(Drawings and Dimensions)
Accessories and Others Connection Flanges

11
Construction Methods 12
Monitoring Devices 13
Specifications 14
Inquiry Form and Brochures 15

1
The BÖRGER Rotary Lobe Pump
- Function and Features -
The BOERGER Rotary Lobe Pump
BOERGER Rotary Lobe Pumps are self-priming, valve less, positive displacement pumps.
With speed-proportional flow, they continuously deliver trouble-free pumping of liquids of
various consistencies and multiphase mixtures. They are compact and operate with low
shear and low pulsation.
BOERGER Rotary Lobe Pumps are used for many different applications. They are
preferred for sludges and suspensions or where abrasive or shear-sensitive products must
be handled.
1. Features
The Function
The parallel, 2-shaft design is

common to all Rotary Lobe Pumps.
The external synchronizing gear
rotates the shafts in opposite
directions.
The displacement rotors are fitted on

the shafts within the pump casing.
The clearances between the rotors
and casing are minimized to
completely isolate the suction and
pressure areas of the pump.
The rotation of the rotors creates a series of chambers within the pump casing. Product
fills the chambers on the suction side and is rotated circumferentially to the pressure side.
This produces a uniform flow from the suction to the discharge side with no need of valves.
The stress to the fluid is negligible as the product is transported almost free of shear and
with little pulsation and acceleration.
Flow Rates
BOERGER Rotary Lobe Pumps are available for flow rates of 0,5 to 1050 m3/h (2 to 4600
USGPM). From 16 different pumps sizes we can select the most suitable pump to meet
our customer’s specification.
Direction of Flow
The absolute symmetrical design allows reversible flow under any operating conditions by
simply changing the direction of rotation of the conveying elements. This allows filling and
emptying of a tank with just one pump system.
The accurate Flow

The large direct inlet opening ensures an easy entrance of high viscosity products or
liquids with rigid, bulky solids. The product passes a short way through the pump’s inner
chamber, which results in a very gentle conveying. Even with fibrous and looping particles,
any clogging or blockage is almost impossible.
Space Requirement
As a result of their compact but robust design BOERGER Rotary Lobe Pumps can be
installed in confined spaces. Various flange configurations and different drive
arrangements are designed for the individual local conditions and specific requirements.
The Timing Gear

The rotary lobes on the carrier shafts are synchronized by two spur gear wheels for high
operating accuracy to permit a partially dry operation without damaging the rubber coated
rotors. The timing gear is in a separately sealed independent unit. High quality gear
wheels ensure an even, smooth operation and a long service life.
One side Bearings

The shafts of the Boerger Rotary Lobe Pumps are guided in large dimensioned roller
bearings. The bearing assembly is separated from the wetted pump chamber and need
not to be disassembled for maintenance purposes.
The Rotary Lobes

The computer controlled manufacturing of the rotary lobes ensures an exact geometry with
small tolerances. Suction and pressure side of the pumps are sealed from each other in a
reliable manner and with perfect conditions, a suction height up to 20 ft. can be achieved.
The elastomer coating is compatible with the chemical and physical properties of the
pumped fluids. Various materials are available, such as wear-resistant elastomers or
plastics. Stainless steel rotors can be provided, too. For extremely abrasive conveying
products, BOERGER offers readjustable rotors.
The BLOCK Pump Casing
The pump casing is made from a single casting, with small tolerances. It is available from
high quality grey cast iron, ductile iron or stainless steel. Both axial faces have replaceable
liners. Optional radial liners can also be supplied to reduce the wear and the spare part
costs. The pump casing can be surface-hardened to make it more wear resistant. The
wetted casing is closed by a quick-release-cover, fixed and tightened by four ring nuts
only, to allow a quick access to the interior.
The Ease of Maintenance
MIP = Maintenance in Place. The BOERGER pump design with its one-side
bearing arrangement allows for quick direct access to the wetted pump
chamber. Rotors or rotor tips and all other wear parts can be replaced within
minutes, without disassembling the pump or removing the suction or
pressure piping. The multi-vane rotors in the CL, FL, and FLA pump models
are equipped with elastomer coated pushed-on rotor tips. The customer’s
personnel can perform maintenance easily and quickly, which reduces
downtime and maintenance costs to a minimum.
The Seals
High quality mechanical seals (e.g. SiSiC) seal the pump shafts. As an alternative to the
standard mechanical seals, we can supply double acting mechanical seals, with
glandpackings or with special seal systems like the MULTI-SEAL K. In all cases the design
and the selected materials are compatible with the specific application.
The Fluid-filled Intermediate Chamber

A intermediate chamber - fluid-filled as standard - is located between the pumping
chamber and the timing gear. The purpose of this chamber is to prevent product
penetration into the timing gear in the event of a seal failure and to provide an indication of
the seal failure. The fluid quenches the mechanical seals and lubricates the rotor-shaft
connection to keep it free from any corrosion.
The Drive
Pumps are driven by helical geared motors as standard. If required, we are also able to
supply variable speed geared motors, combustion engines and hydraulic or pneumatic-
motors. Even submersible motors are possible. Pump and drive are connected via an
elastic coupling and fitted on a common torsion rigid base frame.
The advantages in overview
• powerful
• speed proportional flow
• self-priming
• pressure up to 12 bar (175 PSI)
• short, direct passage
• gentle handling
• easy maintenance with MIP
• Numerous of pump ranges enable an exact adaptation to individual application.
• Due to the symmetrical design, the direction of flow is completely reversible by simply
switching the direction of rotation.
• The large direct inlet opening ensures an easy entrance of high viscosity products or
liquids with rigid, bulky solids.
• The product passes a short way through the pump’s inner chamber, which results in a
very gentle conveying.
• Even with fibrous and looping particles, any clogging or blockage is almost
impossible.
• Only the pump casing, the rotors and the shaft seals are in contact with the product to
be pumped. The other pump elements, even the shafts, are non-wetted by the
conveying product.
• The compact design allows installation in space-limited situations.
• The quick release cover and the one-side bearing design allows easy access to the
operating pump parts without disassembly of the pipe connections or the pump itself.
MIP = Maintenance in Place.
• The materials of all wetted parts are carefully selected to be compatible with the
chemical and physical properties of the product to be pumped.
• The pushed-on, quickly changeable rotor tips of the pumps in the CL, FL and FLA
ranges guarantee easy maintenance with low costs.
• Stainless steel rotors are available for all pumps, and some models offer rotors from
PTFE.
• The rotors are machined via computer control, which ensures an exact geometry
with small tolerances.
• For abrasive products, dual-vane, readjustable rotors are available.
• With the helical screw lobe design, almost pulsation free conveying is achieved.
• Wear-resistant pump casing in a one-piece block design are equipped with axial
casing liners as standard and optional radial liners from hard metal or from Silicon
Carbide for some specific ranges.
• The carrier- and synchronizing gear is in a separate sealed unit. The strong shafts and
hardened gear wheels ensure high torque and power transmission.
• The high quality mechanical seals are suitable for high-pressure peaks and are easy
to maintain.
• The intermediate chamber in between the synchronizing gear and the pump casing is
filled with quench fluid. This fluid prevents any dry running of the mechanical seals and
indicates possible seal leakage.
• The overall dimension sheets show the compact design with geared motors. For
space-limited applications the drive can be fitted over the pump, with v-belt
transmission. A complete aggregate for app. 150 m3/h (660 GPM) requires app. 1 m2
(10 ft2) only.
• Complete pump units are available with geared motors, variable speed geared
motors, submersible drives or hydraulic motors. Even stationary or mobile units with
combustion engines are available.
• Unlimited variations and applications.

Fields of Application
Environmental Technology
Sewage, municipal or industrial, sludge, thin or thickened, dosing of polyelectrolyts, feeding
of dewatering devices, lime slurries in flue gas desulphuration, water-oil-mixtures
Chemical Industry
Acids, caustics, mixtures, solvents, fats, oils, pastes, dispersions, emulsions, latex or
products containing latex, paints and coatings
Oil Industry
Oil, oil sludge, heavy oil, fuel oil, diesel oil, benzene, kerosene, water-oil-mixtures, emulsions
Building Industry
Mineral sludge, cement slurry, bentonite, drilling emulsion, drilling mud, lime slurry, plaster
masses, coatings, de-watering
Paper and Paper

Paper stock, coatings, chemicals, paints, lime milk, wastewater, sewage,
caoline suspensions, titanium dioxide
Ceramic Industry
Clay, lime slurries, ceramic slickers, ferric oxide slurries, glazings
Fish and Meat Processing

Train oil, entrails, blood, roe, fish meal slurries, chopped meat, sewage, rinds, fats, bone
slurries
Fruit and Vegetables Processing

Pulps, fruit pap, chopped vegetables or fruits, sewage
Marine
Bilge water, leakage water, ballast water, fuel oil, oil sludge, sewage
Starch Production
Wash water, pulps, starch milk, mashes, and syrup
Sugar Industry
Wash water, molasses, calcium carbonate slurries, press water, sewage
Mining
Pit water, flotation sludge, lime slurries
Agriculture
Liquid manure, sewage, animal feeding, food wastes, biogas plants
2
Components of the
BÖRGER Rotary Lobe Pump
The Components of the BOERGER Rotary Lobe Pump
1. Bearing and timing gear
2. Intermediate quench chamber
3. Casing in Block design
4. Axial and radial casing liners
5. Shaft seals
6. Rotary Lobes
7. Quick-release-cover
8. Non-wetted shafts
7 4 2 1
6 5 8 3
6
Components
1. Bearing and Timing Gear
The timing gear is in a separately sealed construction element. The high quality and robustly
designed gear wheel ensure a precise transmission and long service life.
BLOCK-casing, machined with

small tolerances
High quality low-friction bearings guarantee high load capacity and long service life
Oversized self-aligning bearing, Cylinder roller bearing, permits

axially fixed axial shifts and prevents tensions
Timing gear with precisely made gear wheels

for low noise and clearance-free operation
Components
2. Intermediate Chamber
The fluid-filled and separately-sealed intermediate chamber divides the timing gear from the
wetted pump chamber. It protects the gear from penetration of conveying liquid and the pump
chamber from contact with gear oil. It is also the seal quench.
Any seal failures are indicated early by quench fluid overflow.
Upon request we can supply a seal monitoring system, which supervises any seal leakage
via a conductivity probe.
Timing gear Wetted pump chamber

Intermediate Chamber
Seal monitoring probe (optional)

Components
3. BLOCK-Pump casing
The wetted pump casing is made from a single BLOCK-casing with low tolerances. It is
available from high quality grey cast iron, ductile iron or stainless steel. A quick release cover
fitted with just four ring nuts closes the casing.
This allows an easy and quick access to the inner
parts of the pump.
Each pump casing is cast separately in one piece

and exactly machined via CNC controlled
equipment.
Large direct inlet / outlet openings for continuous

flow, even with large solids and high viscosities.
One individual casing length for each pump size.

Components
4. Axial and radial casing protection liners
Axial casing protection liners are fitted as standard at both face ends of the wetted pump
casing. The liners are made from hard metal, hardened steel or specially treated stainless
steel. The front side clamped in liner between the casing face and the quick release cover as
well as the screwed-in rear plate is easily accessible because of the quick release cover.
The majority of the BOERGER pump-range can be equipped with additional radial protecting
liners made from hardened steel or stainless steel. These MIP radial liners are positioned
with clamping devices, which are screwed from outside and easily replaced like the axial
ones.
When using these liners, all parts without exceptions that are subject to wear are accessible
and replaceable through the quick release opening. The pump needs not to be dismantled for
inspection or maintenance.
So a consequent MIP = Maintenance in Place is ensured.
axial
radial
axial
Components
5. Shaft Seals
Opposite to a lot of other positive displacement pumps, BOERGER Rotary Lobe Pumps have
got single acting mechanical seals with quench as standard.
These maintenance free shaft seals are available from different materials, adapted to the
pumped liquid. Also, the elastomers are selected individually for each application.
The quench as standard ensures a good lubrication of the seal faces, even in case of short
term dry running or in vacuum operation. It also prevents sedimentation of product or
crystals, which could appear from contact with the atmosphere.
Special designs such as double acting mechanical seals are available upon request.
For applications where the use of mechanical seals is not sensible, BOERGER offers pumps
with gland packing, with or without a seal gage ring for flush or lubrication.
A special innovation is the BOERGER MULTISEAL system, a specially developed radial

shaft seal for various sticky or quick hardening conveying products.
All shaft seals are accessible through the quick release opening and are replaceable as a
cartridge unit. So here too: MIP = Maintenance in Place
Mechanical Seal Gland Packing MULTISEAL

Components
6. Rotors
Entirely elastomer coated rotors are preferable
for use when conveying aggressive fluids. The metal
core and thus the metal-elastomer bonding is not in
contact with the pumped liquid. The shape of the
coating ensures a seal at the ends of the rotor with
the pump casing.
For abrasive products there are entirely elastomer

coated rotors available in a re-adjustable design.
In the case of wear the vanes can be readjusted
via an integrated mechanism to regain the seal
with the surrounding casing and the other rotor.
Patent.
To convey extremely problematic fluids, i.e. solvents,

Boerger offers rotors from stainless steel or PTFE.
Fluids contaminated with solids are the ideal appli-

cation for BOERGER Rotary Lobes with pushed-on,
quickly changeable, elastomer coated tips.
This special maintenance friendly solution is proven
especially in large pumps. Spare parts costs and
maintenance efforts are reduced dramatically. The
rotor base parts are available from ductile iron,
stainless steel or special materials.
Patent.
Although Rotary Lobe Pumps generate low pulsations,

there are rotors in helical screw geometry available
for pulsation sensitive applications. With this geometry
any pulsation is reduced to a non measurable value.
Screw rotors are available in the entirely elastomer-
coated design for the PL range only, and with
replaceable tips for CL, FL and FLA ranges.
Patent.
A real innovation are the new BOERGER Optimum

rotors. The especially strong designed entirely rubber
coated vanes have got the same radius as the pump
casing. This screwed form results in a large sealing
face with multiple longer service life.
Patent.
The rotors are adopted to each individual pplication.

Beside different metals there are different elastomers,
plastics or special materials available. The building kit
system ensures that almost all rotors can be fitted to
previously supplied pumps.
Components
7. Quick Release Cover
The robust design of BOERGER Rotary Lobe Pumps with one side bearings as a matter of
principle allows the quick release cover with the best access possible to all parts being
wetted and subject to wear. All of these parts can be easily inspected and simply be replaced
if needed.
After removing just four ring nuts the quick release cover can be taken off, which makes
maintenance easy.
For any replacement of worn parts the pump does not need to be separated from the system.
Even the suction and pressure pipe connections remain fitted. There is no need for
removable pipe pieces or spacer couplings in connection with BOERGER Rotary Lobe
Pumps.
Also for pumps with additional shaft support systems in the quick release cover, the
additional bearings are integrated into the cover and can be removed together with it. So the
huge maintenance advantage of the one side bearing system remains in existence for these
pumps too.
Maintenance friendly in perfection!
MIP = Maintenance in Place
Maintenance free additional shaft support

Components
8. Non-wetted Shafts
The conveying product because of the special self-sealing design does not wet the carrying
shafts of BOERGER Rotary Lobe Pumps.
The connection between the rotors and the shafts is continuously wetted by the lubricant
liquid from the intermediate chamber and thus protected from corrosion. Even after extended
operation, an easy and trouble-free exchange of the rotors is ensured.
The self-sealing design of the entirely elastomer coated rotors prevents any contact of the
pumped liquid with the shafts. With all other rotors this is ensured by separate O-rings.
3
Performance Overview
Pump Series Overview of BOERGER Rotary Lobe Pump
Q [m^3/h]
Q [USGPM]
1 10 100 1000
4,4 44 440 4400
AL25
AL50
AL75
PL100
PL200
PL300
CL260
CL390
Model
CL520
FL518
FL776
FL1036
FLA 1540
XL1760
XL2650
XL3530
n=300 rpm n=450 rpm-1 p = max. 12 bar /174 (depending on model)

4
AL Series
AL Series
AL 25
Weight 35,5 kg
Measure above single flange [A] / Measure above flanges [B]
AL 25 DN 32 [mm] *DN 40 [mm] DN 50 [mm] DN 65 [mm] DN 80 [mm]

DIN 2633 96/350 101/360 116/390 111/380 141/440
ANSI 150 114/384 121/400 135/428 135/428 146/450
* Standard flange
Dimensions may differ due to production reasons!

AL Series
AL 25
front side arrangement
overhead drive assembly
Drive Weight Dimensions

[kW] [kg] L1 [mm] H1 [mm] L2 [mm] H2 [mm]
1,1 75 780 224 597 581
1,5 79 780 224 597 581
2,2 85 878 245 695 602
3 96 907 245
4 101 930 257
5,5 125 1021 276
7,5 136 1059 276
* Standard flange

AL Series
AL 50
Weight 39 kg
AL 50 DN 40 [mm] *DN 50 [mm] DN 65 [mm] DN 80 [mm] DN 100 [mm]

DIN 2633 126/410 121/400 121/400 136/430 141/440
ANSI 150 146/450 140/438 146/450 156/470 165/488
* Standard flange

AL Series
AL 50

1,1 80 818 224 597 581
1,5 84 818 224 597 581
2,2 90 916 245 695 602
3 101 945 245
4 106 968 257
5,5 130 1059 276
7,5 141 1097 276
* Standard flange

AL Series
AL 75
Weight 48 Kg
AL 75 DN 50 [mm] *DN 65 [mm] DN 80 [mm] DN 100 [mm]

DIN 2633 171/500 141/440 131/420 141/440
ANSI 150 191/538 165/488 151/440 165/488
* Standard flange

AL Series
AL 75

1,1 85 858 224 597 581
1,5 89 858 224 597 581
2,2 95 956 245 695 602
3 106 985 245
4 111 1008 257
5,5 135 1098 276
7,5 146 1139 276
* Standard flange

5
PL Series
PL Series
PL 100
Weight 96 kg
PL 100 DN 50 [mm] DN 65 [mm] *DN 80 [mm] DN 100 [mm] DN 125 [mm]

DIN 2633 176/610 141/540 146/550 16/550 176/610
ANSI 150 195/648 166/590 161/580 170/598 210/678
* Standard flange

PL Series
PL 100

1,5 155 1100 414 656 834
2,2 160 1150 414 706 834
3 175 1150 414 706 834
4 190 1176 426 732 846
5,5 200 1233 453 789 846
7,5 245 1295 453 831 873
9,2** 265 295 453
11** 275 1420 453
15** 305 1467 481
* Standard flange
** not available as overhead mounted arrangement

PL Series
PL 200
Weight 107 kg
PL 200 DN 80 [mm] *DN 100 [mm] DN 125 [mm] DN 150 [mm] DN 200 [mm]
DIN 2633 156/570 136/530 151/560 181/620 211/682
ANSI 150 175/608 160/578 185/628 236/730
* Standard flange

PL Series
PL 200

2,2 175 1150 414 706 834
3 180 1150 414 706 834
4 205 1176 426 732 846
5,5 215 1233 426 789 846
7,5 240 1295 453 831 873
9,2** 270 1295 453
11** 295 1420 453
15** 320 1467 481
* Standard flange

PL Series
PL 300
Weight 115 kg
PL 300 DN 80 [mm] DN 100 [mm] *DN 125 [mm] DN 150 [mm] DN 200 [mm]
DIN 2633 236/730 201/660 161/580 166/590 196/650
ANSI 150 261/770 225/708 196/650 222/702 236/730
* Standard flange

PL Series
PL 300

2,2 190 1150 414 706 834
3 205 1150 414 706 834
4 220 1176 426 732 846
5,5 230 1233 426 789 846
7,5 275 1295 453 831 873
9,2** 295 1295 453
11** 305 1420 453
15** 335 1467 481
* Standard flange

6
CL Series
CL Series
CL 260
Weight 180 kg
CL 260 DN 80 [mm] DN 100 [mm] DN 125 [mm] DN 150 [mm] DN 200 [mm]
DIN 2633 165/630 150/600
ANSI 150

CL Series
CL 260

[kW] [kg] L1 [mm] H1 [mm] L2 [mm]
3 293 1365 500 800
4 308 1390 515 825
5,5 318 1525 530 935
7,5 363 1525 530 935
9,2 383 1560 530 945
11* 393 1665
15* 423 1665
* not available as overhead mounted arrangement

CL Series
CL 390
Weight 200 kg
DIN 2633 195/690 160/615 175/650 160/620 260/820
ANSI 150 195/690 200/700

CL Series
CL 390

[kW] [kg] L1 [mm] H1 [mm] L2 [mm]
3 313 1365 500 800
4 328 1390 515 825
5,5 338 1525 530 935
7,5 368 1525 530 935
9,2 403 1560 530 945
11* 413 1665
15* 443 1665
18,5* 462 1775

CL
Series
CL 520
Weight 200 kg
DIN 2633 250/795 165/625
ANSI 150

CL Series
CL 520

[kW] [kg] L1 [mm] H1 [mm] L2 [mm]
3 333 1365 500 800
4 348 1390 515 825
5,5 358 1525 530 935
7,5 388 1525 530 935
9,2 423 1560 530 945
11* 433 1665
15* 463 1665
18,5* 482 1775

7
FL and FLA Series
FL & FLA Series
FL 518
Weight 262 kg
FL 518 *DN 125 [mm] DN 150 [mm] DN 200 [mm]

DIN 2633 166/680 176/700 251/850
ANSI 150 200/748 232/812 291/930
* Standard flange

FL & FLA Series
FL 518

3 305 1437 535 1066 818
4 315 1463 547 1078 844
5,5 335 1520 547 1078 901
7,5 370 1530 574 1105 911
9,2 395 1530 574 1105 911
11 400 1655 574 1105 1014
15 480 1702 602 1133 1061
18,5** 535 1839 602
22** 560 1839 602
30** 610 1839 602
37** 780 1946 634
45** 810 1946 634
* Standard flange

FL & FLA Series
FL 776
Weight 288 kg
FL 776 DN 125 [mm] *DN 150 [mm] *DN 200 [mm]

DIN 2633 201/750 176/700 151/650
ANSI 150 200/748 232/812 291/930
* Standard flange

FL & FLA Series
FL 776

4 340 1463 547 1078 844
5,5 360 1520 547 1078 901
7,5 395 1530 574 1105 911
9,2 420 1530 574 1105 911
11 425 1655 574 1105 014
15 505 1702 602 1133 1061
18,5** 560 1839 602
22** 585 1839 602
30** 635 1839 602
37** 805 1946 634
45** 865 1946 634
* Standard flange

FL & FLA Series
FL 1036
Weight 296 kg
FL 1036 DN 150 [mm] *DN 200 [mm] DN 250 [mm]

DIN 2633 226/800 201/750 200/780
* Standard flange

FL & FLA Series
FL 1036

5,5 390 1520 547 1078 901
7,5 425 1530 574 1105 911
9,2 450 1530 574 1105 911
11 500 1655 574 1105 1014
15 540 1702 602 1133 1061
18,5** 590 1839 602 1133 1179
22** 615 1839 602 1133 1179
30** 665 1839 602
37** 835 1946 634
45** 895 1946 634
* Standard flange

FL & FLA Series
FLA 1540
Weight 385 kg
Measure above flanges [A]
FL 1540 DN 200 [mm] *DN 250 [mm] DN 300 [mm] DN 350 [mm] DN 400 [mm]
DIN 2633 900 800 1000 1000 1000
* Standard flange

FL & FLA Series
FLA 1540

[kW] [kg] L1 [mm] H1 [mm] e [mm] f [mm]
11 755 1950 590 370 2000
15 875 1997 618 370 2000
18,5** 900 2099 618 370 2200
22** 918 2099 618 370 2200
30** 1045 2241 649 370 2200
37** 1096 2312 649 370 2400
45** 1130 2403 649 370 2400
* Standard flange

8
XL Series
XL Series
XL 1760
Weight app. 1100 kg
FL 1540 DN 200 [mm] *DN 250 [mm] DN 300 [mm] DN 350 [mm] DN 400 [mm]
DIN 2633 - 1070 - - -
* Standard flange

XL Series
XL 1760

45 ca. 1900 3140 995 602,5 160

Baureihe XL
Maße können produktionsbedingt leicht abweichen!

XL Series
XL 2650
Weight app. 1300 kg
FL 1540 DN 200 [mm] DN 250 [mm] *DN 300 [mm] DN 350 [mm] DN 400 [mm]
DIN 2633 - - 1070 - -
* Standard flange

XL Series
XL 2650

75 ca. 2700 3140 1033 602,5 160

Baureihe XL

XL Series
XL 3530
Weight app. 1500 kg
FL 1540 DN 200 [mm] DN 250 [mm] DN 300 [mm] *DN 350 [mm] DN 400 [mm]
DIN 2633 - - - 1070 -
* Standard flange

XL Series
XL 3530

90 ca. 3000 3140 1033 602,5 160

Baureihe XL

9
The Börger Multicrusher
The BOERGER Multicrusher
The Multicrusher is an effective, widely applicable dual-shaft macerating unit for

reducing solids in liquids. It chops solids like fibres, wood, glass, plastics, skins,
textiles or similar.
It incorporates the same unique advantages of the Boerger MIP-Design as the
Boerger Rotary Lobe Pumps: Shafts, bearings, seals and casing parts are identical.
The Boerger Multicrusher is used in many industries. Especially where solids create
problems in the manufacturing or operating procedure and need to be reduced to no
more critical dimensions. With such treatment of the fluids the following machines
and pumps are protected
1. Features
The Function
Two parallel shafts are rotated

via an external gear in opposite
directions. Each of the both
shafts is equipped with cutter
blades, meshing each other. The
cutter blades pull-in the solids in
the liquid and chop it, while the
liquid flows through the gabs
between the knife blades and
between the teeth. The knife
blades mesh each other with
minimised clearance and though
optimised tearing and cutting
effect.
The relative rotation speed of the two shafts ensures an optimized macerating effect
and prevents stringy material from wrapping around the blades and cutters.
With five different sizes, variable knife blade combinations and optimized rotating
speeds this machine can be adapted to almost any application.
Different materials – also for corrosive fluids – allow the use of the Boerger
Multicrusher even in combination with seawater.
Flow Rates
Boerger Multicrushers are available for flow rates up to 300 m3/h, depending on the
solids content and the kind of solids. From five different sizes we can select the most
suitable machine to meet our customer’s requirements.
Direction of Flow
The absolute symmetrical design allows the reversion of the direction of flow – in any
application - by simply turning the knife blades and the direction of rotation.
Trouble-free Operation
The large direct inlet opening ensures an easy entrance of high viscous products or
liquids with rigid, bulky solids. Although the product passes a short way through the
Multicrusher the solids are caught and securely chopped down. The different relative
circumference rotation speed of the knife blades increases the cutting effect and
ensures a self-cleaning in case of soft and sticky solids.
Space Requirement
As a result of their compact but robust design Boerger Multicrushers can be installed
in confined spaces. Various flange configurations and different drive arrangements
are designed for the individual local conditions and specific requirements.
The Carrier Gear

The knife blades on the non wetted carrier shafts with pushed-on hexagonal sleeves
are guided by two spur gear wheels for high operating accuracy to permit a partially
dry operation of the machine. The carrier gear is a separately sealed independent
unit. High quality gear wheels ensure an even, smooth operation and a long service
life.
One side Bearings

The shafts of the Boerger Multicrusher are guided in large dimensioned roller
bearings. The bearing assembly is separated from the wetted operation chamber and
need not to be disassembled for maintenance purposes.
The Knife Blades

The computer controlled manufacturing of the knife blades ensures an exact
geometry with optimized tearing and cutting effect in each combination. This allows
the adaptation to each specific application and later conversion is easily possible,
too. The materials are selected according to the chemical and physical
characteristics of the products.
The BLOCK Casing
The Multicrusher casing is identical with the pump casing and made from a single
casting, with small tolerances. It is available from high quality grey cast iron, ductile
iron or stainless steel. Both axial faces have replaceable liners to reduce the wear
and the spare part costs. The Multicrusher casing can be surface-hardened to make
it more wear resistant. The wetted casing is closed by a quick-release-cover, fixed
and tightened by four ring nuts only, to allow a quick access to the interior.
The Ease of Maintenance
MIP = Maintenance in Place. The Boerger Multicrusher design with its one-
side bearing arrangement allows for quick direct access to the wetted
operation chamber. The knife blades and all other wear parts can be
replaced within minutes, without disassembling the machine or removing the
inlet and outlet piping. The knife blades and the intermediate distance rings
are simply pushed on to hexagonal sleeves. The customer’s personnel can
perform maintenance easily and quickly, which reduces downtime and
maintenance costs to a minimum.
The Seals
High quality mechanical seals seal the Multicrusher shafts. In all cases the design
and the selected materials are compatible with the specific application.
The Fluid-filled Intermediate Chamber

An intermediate chamber - fluid-filled as standard - is located between the operation
chamber and the carrier gear. The purpose of this chamber is to prevent product
penetration into the carrier gear in the event of a seal failure and to provide an
indication of the seal failure. The fluid quenches the mechanical seals and lubricates
the sleeve-shaft connection to keep it free from any corrosion.
The Drive
Multicrushers are driven by helical geared motors as standard. If required, we are
also able to supply variable speed geared motors, combustion engines and hydraulic
or pneumatic-motors. Even submersible motors are possible. Multicrusher and drive
are connected via an elastic coupling and fitted on a common torsion rigid base
frame.
Components of the BOERGER Multicrusher
1. Carrier Gear
2. Quench- and Intermediate Chamber
3. Casing in Block design
4. Axial Casing Liners
5. Cutting- and Counter Blades
6. Distance Rings
7. Sealing Discs
8. Central Fitting Screws
9. Non-wetted Shafts Hexagonal Sleeves
10. Quick-release Cover
10 4 6 2 1
8 7 5 9 3
5
The Boerger Multicrusher is an effective, widely applicable macerating unit based on
the proven design of the Boerger Rotary Lobe Pump. For details please refer to the
identical components in chapter 2.
1. Carrier Gear
The carrier gear is in a separately sealed construction element. The high quality and robustly
designed gear wheel ensure a precise transmission and long service life.
2. Quench- and Intermediate Chamber

The fluid-filled and separately-sealed intermediate chamber divides the carrier gear from the
wetted operation chamber. It protects the gear from penetration of liquid and the operation
chamber from contact with gear oil. It is also the seal quench.
3. BLOCK-Casing
The wetted Multicrusher casing is made from a single BLOCK-casing with low tolerances. It
is available from high quality grey cast iron, ductile iron or stainless steel. A quick release
cover fitted with just four ring nuts closes the casing. This allows an easy and quick access to
the inner parts of the machine.
Large direct inlet / outlet openings for continuous flow, even with large solids and high
viscosities.
4. Axial Casing Liners

Axial casing protection liners are fitted as standard at both face ends of the
wetted Multicrusher casing. The liners are made from hard metal, hardened
steel or specially treated stainless steel. The front side clamped in liner between
the casing face and the quick release cover as well as the screwed-in rear plate
is easily accessible because of the quick release cover.
All parts without exceptions that are subject to wear are accessible and replaceable through
the quick release opening. The Multicrusher needs not to be dismantled for inspection or
maintenance.
So a consequent MIP = Maintenance in Place is ensured.

5. Cutting- and Counter Blades
Different knife blades and combinations are available for a best possible adaptation to each
individual application.
Knife G10Z, coarse with 10 teeth – preferred for pull-in and

chopping of very large solids.
Knife F16Z, medium teething with 16 teeth, for achieving a

good macerating effect. Also suitable for stringy materials.
Knife G8Z, coarse with 8 teeth, preferred as counter knife in

combination with one of the knife blades described above.
SF16Z, very fine teething with 16 teeth. To be used for

extraordinary chopping requirements.
Typical Combinations
G10Z combined with G8Z for pre-macerating of re-growing

raw material, being fed into Biogas plants for digestion.
F16Z combined with G10Z for chopping of slaughterhouse

wastes in a huge plant for slaughtering pigs.
SF16Z combined with F16Z for macerating and

homogenisation.
6. Distance Rings
Distance rings fitted between the knife blades ensure the exact clearance for perfect
meshing of the blades with best possible cutting effect. The materials are adapted to the
individual application.
7. + 8. Sealing discs and Central Screws

The sealing discs with the central screws build the front side locking and allow the easy
access to the knifes with easy maintenance.
9. Non-wetted shafts with Hexagonal Sleeves

Based on the design of the Boerger Rotary Lobe Pump the shafts of the Multicrusher are not
wetted, too and are made of the same strong material.
The pushed-on hexagonal sleeves are made from fluid adapted materials and allow easy
assembly and disassembly of the knife blades.

The robust design of Boerger Multicrusher with one side bearings as a matter of principle
allows the quick release cover with the best access possible to all parts being wetted and
subject to wear. All of these parts can be easily inspected and simply be replaced if needed.
After removing just four ring nuts the quick release cover can be taken off, which makes
maintenance easy.
For any replacement of worn parts the Multicrusher does not need to be separated from the
system. Even the inlet and outlet pipe connections remain fitted. There is no need for
removable pipe pieces or spacer couplings in connection with Boerger Multicrushers.
Also for machines with additional shaft support systems in the quick release cover, the
additional bearings are integrated into the cover and can be removed together with it. So the
huge maintenance advantage of the one side bearing system remains in existence for these
Multicrushers, too.
Maintenance friendly in perfection!
MIP = Maintenance in Place

Multicrusher
HAL 50
Drive Weight L1 H1
[kW] [kg] [mm] [mm]
1,5 84 818 224
2,2 90 916 245
Measure above single flange [A] / both flanges [B]
Diameter DIN 2633 ANSI 150

DN 40 [mm] 126/410 146/450
DN 50 [mm] 121/400 140/438
DN 65 [mm] 121/400 146/450
DN 80 [mm] 136/430 156/470
* Standard flange

Multicrusher
HPL 200
Drive Weight L1 H1
[kW] [kg] [mm] [mm]
3,0 180 1150 414
4,0 205 1176 426

DN 100 [mm] 136/530 160/578
DN 125 [mm] 151/560 185/628
DN 150 [mm] 181/620 236/730
DN 200 [mm] 211/682
* Standard flange

Multicrusher
HCL 390
Drive Weight L1 H1
[kW] [kg] [mm] [mm]
5,5 338 1525 530
7,5 368 1525 530

DN 100 [mm] 160/615 -
DN 125 [mm] 175/650 194/690
DN 150 [mm] 160/620 200/700
DN 200 [mm] 260/820 -
* Standard flange

Multicrusher
HFL 776
Drive Weight L1 H1
[kW] [kg] [mm] [mm]
9,2 420 1530 574
11 425 1655 574

DN 125 [mm] 201/750 200/748
DN 150 [mm] 176/700 232/812
DN 200 [mm] 151/650 291/930
* Standard flange

Multicrusher
HLA 1540
Drive Weight L1 H1 e f
[kW] [kg] [mm] [mm] [mm] [mm]
18,5 900 2099 618 370 2200
22 918 2099 618 370 2200
Measure above both flanges [A]
Diameter DIN 2633

DN 200 [mm] 900
DN 250 [mm] 800
DN 300 [mm] 1000
* Standard flange

Design Guideline for Börger Multicrusher
The flow capability of the Multicrusher depends on the dry

solid (DS) content of the fluid. The higher the DS content, the
Sludge / max 30% DS smaller the capacity, otherwise resistance and therefore
or almost not flowing pressure drop would be too high through the unit..
material
Sludge / max 20% DS Multicrusher Typ max. Flow Fluid Velocity

or barely flowing
HAL 15 m³/h 1,5 m/s
material
HPL 60 m³/h 3,0 m/s
Sludge / max 12% DS HCL 120 m³/h 3,1 m/s
or fair flowing material
HFL 200 m³/h 3,1 m/s
HLA 310 m³/h 2,3 m/s
Sludge / max 6% DS
or flowing material c
Description: Sludge with 12% DS content needs to be
Sludge / max 3% DS macerated. According to the diagram 50% of the max. flow is
or good flowing possible for the Multicrusher.
material HAL = 7.5 m³/h; HPL= 30 m³/h; HCL = 60 m³/h;
Sludge / max 1% DS HFL = 100 m³/h, HLA = 155 m³/h.
or very good flowing
material
Examples:
Waterlike Fluids max. flow a) 25 m³/h, 18 % TS = max. 25% Æ Typ HCL
HAL= 3,75 m³/h, HPL= 15 m³/h, HCL= 30 m³/h, HFL= 50 m³/h, HLA= 77 m³/h
b) 85 m³/h, 4 % TS = max. 60% Æ Typ HFL
HAL= 9 m³/h, HPL= 36 m³/h, HCL= 72 m³/h, HFL= 120 m³/h, HLA= 186 m³/h
0% 20% 40% 60% 80% 100%
Disclaimer: This datasheet incorporates only general design guidelines based on experiences in the field. The technical information allow preliminary design
calculations. No warranties can be claimed based on the datasheet.
For determination of a Börger Multicrusher for your specific application, please contact us.
Börger GmbH Tel: +49 (0) 28 62 • 91 03-0

Benningsweg 24 Fax: +49 (0) 28 62 • 91 03-46
46325 Borken-Weseke www.boerger.de
Germany info@boerger.de
10
The Börger Multichopper I
The BOERGER Multichopper
The Boerger Multichopper is a macerator with central cutterplate and twin opposing
rotating knifeheads for reducing solids in liquids. It chops down cutable solids.
Multichoppers are used mainly in the wastewater treatment technology but in various
other industries, too.
1. Features
The Function
The product, consisting of fluid –

usually water - with large solids,
is conveyed through the openings
of the cutterplate with the use of a
pump.
The rotating knifeheads on both
sides of the cutterplate create six
cuts per each revolution ensuring
a reliable, trouble-free chopping
and reducing of the solids.
The twin opposing rotating
knifeheads with triple replaceable
knifes each are fitted on gab
against each other.
The central adjusting unit with an
external clamp construction keeps
the assembly axially aligned and
allows easy readjusting.
The chopping result is mainly influenced by the design of the cutterplate, the
throughput volume and the rotation speed.
Non cutable solids – such as stones or hard metal particles – are separated prior to
the entry into the cutterplate and collected in the large debris collection area below,
from which they can be easily removed frequently.
The Throughput Volume
The possible throughput volume depends on the solids content of the product and on
the individual design of the cutterplate.
With sewage or wastewater having a solids content of app. 3 – 5 % we can allow a
throughput flow volume of up to app. 100 m³/h.
The Direction of Flow

The product is conveyed through the cutterplate in the direction towards the drive.
With the special design of the reversible flange connections of the Multichopper
range I the direction of flow can be determined by the customer. The diameter and
standard of the flange connections is adapted to the specific application.
The trouble-free Operation

The combination of a Multichopper with a Rotary Lobe Pump ensures an even and
smooth throughput. The two rotating knifeheads at both sides of the cutterplate catch
and cut the solids being in the product.
The Space Requirement

The compact design of the Multichopper I allows fitting even in case of limited space.
All parts in contact with the product are assessable from outside without
disassembling the machine.
The Re-adjusting
Knife to plate tension is adjustable from the outside of the assembly, a central shaft
clamp construction keeps the assembly axially aligned and can easily be re-adjusted.
The cutterplate is fixed in a radial position between the two knifeheads along the
common shaft.
The Cutterplate
There are cutterplates available in different design and from different materials, which
are selected according to the individual application.
This allows adapting the chopping degree to the requirements.
The easy Maintenance

MIP = Maintenance in Place. The Multichopper with one-side bearing construction
includes technically friendly operational design improvements with easy access to the
operational area. In case of need the knifes, the cutterplate and the further product
loaded parts can simply be replaced in minutes, without disassembly of the machine
or the flange connections. The central adjusting unit allows readjusting from the
outside.
The Shaft Seal
The shaft seal is furnished with a proven Boerger recognized high quality mechanical
seal with quench and control. The quench ensures lubrication of the seal in all
operation conditions and long service life.
The Fluid-filled Quench

The typical Boerger shaft seal design includes a fluid-filled intermediate chamber
between the operation area and the flanged drive unit. This protects the drive from
penetration by product and allows easy control of the seal.
The Drive
As standard the Multichopper is driven via a parallel shaft geared motor. As
alternative a hydraulic motor drive can be realized.
The Components of the BOERGER Multichopper
1. Both sides triple Knifeheads with replaceable Knifes
2. Casing
3. Parallel Shaft Geared Motor with Hollow Shaft
4. Central Adjusting Unit
5. Reversible Connection Flanges
6. Debris Collection Area
7. Cutterplate
8. Fitting Screw
1 2
9 8 7 6 5 4 3
The Boerger Multichopper is a Cutterplate-Macerator in inline-design incorporating the
Boerger MIP features. Our customers appreciate the flexibility due to little space
requirements and the possibility of changing the direction of throughput by reversing
the flanges
1.Triple Knifeheads with replaceable Knifes

In opposite to most other macerators the Boerger Multichopper is equipped with
knifeheads at both sides of the cutterplate. With the resulting six macerating cuts per
revolution a very good chopping effect is achieved. The knifes are replaceable
individually.
2. Casing
The Multichopper-Casing as stabile construction with integrated debris collection area
for non cutable solids.
3. Parallel Shaft Geared Motor with Hollow Shaft

The drive as parallel shaft gear with hollow shaft allows central re-adjusting of the
macerating unit via just one central re-adjusting unit.
4. Central Adjusting Unit

Knife to plate tension is adjustable from the outside of the assembly; a central shaft
clamp construction keeps the assembly axially aligned.
5. Reversible Flange Connections

Genius design of flange connections. The direction of flow can be determined and
changed by the customer by simply reversing the flange connections.
Of course there are different flange diameter and standards available.
6. Debris Collection Area
Save separation of non-cutable solids. Stones and metal parts – with higher specific
gravity - are collected in the debris area below the cutting unit and can be easily
removed through the front cleaning opening.
7. Cutterplate
The cutterplate is fixed in a radial position
between the two knife-heads along the
common shaft.
Different plate designs are available to adapt
to the individual requirements. The
hardenend steel material ensures long
servive life.
8. Fitting Screw
The fitting screw is the counter parts to the central adjusting unit. It is responsible fort
he optimal tension of the knifeheads towards the cutterplate.

After loosing of just four ring nuts the quick release cover can be removed. This makes
maintenance quick and easy. For changing of product loaded parts the machine need
not to be removed from the system. Even the inlet and outlet pipe connections remain
fitted. There is no need of any bypass or dummy for the time of maintenance.
Dimensions of the Multichopper-I:
Other flange sizes are possible,

The width dimension then remains
unchanged.

11
Connection Flanges
Flanges
An Extract from our Possibilities:
Standard: Transition from rectangle pump connection to standard flange
BÖRGER
Elbow, flange pointed upwards
BÖRGER
Optional also downwards
Elbow, flange pointed forward
BÖRGER
Optional also backwards
Different flanges connections right and left side are possible.

Flanges
Quick connect coupling, Storz
BÖRGER
Connection with quick coupling, System Perrot, with female end 4“ to 8“
BÖRGER
Gooseneck design, recommended with mobile pumps
For space restricted applications
BÖRGER
Optional also downwards, forwards and backwards

Flanges
Double elbow, pointed upwards, with flange connection
BÖRGER
Double elbow, pointed upwards, with quick coupling connection
BÖRGER
Infinitely variable unlimited twistable suction and discharge connection, with quick
coupling, System Perrot
BÖRGER

12
Construction Methods
1. Standard Layout
BÖRGER
Pump with gear motor and elastic coupling assemble on a high-quality, torsion-
resistant, welded and corrosion-proof base frame.
2. Overhead Drive Assembly
BÖRGER
Power transmission by toothed belt or V-belt.
Especially for restricted spaces by means of the space saving arrangement of pump
and drive.
3. Mechanically Adjustable Variable Speed Drive
BÖRGER
Drive as mechanically adjustable variable speed drive for adjustment of conveying

capacity.
4. Helical Bevel or Worm Geared Motor
BÖRGER
For use in extreme conditions, e.g. in a narrow tunnel, where a standard solution is
not possible.
5. Hydraulic Motor
BÖRGER
Driven by hydraulic motor, direct flanged to pump shaft.

Especially appropriate for installation on a vehicle.
6. Submersible Unit
NORD
Driven by flanged geared motor with elastic coupling in a sealed lantern. Drive in dry
area.
Also available with guide rails and coupling foot.
7. Submersible Pump with elongated Drive Assembly
N O RD
Long-shaft-design with crane hooks and

stand pipe.
Also available with guide rails and

coupling foot.
.
8. Submerged Aggregate
Complete aggregate submerged.
Also available with guide rails and

coupling foot.
9. Pump Aggregate on Trolley
BÖRGER
Ideal for mobile applications.
The quick couplings at suction and discharge allow easy and quickly handling with
suction and pressure hoses.
10. Trailer mounted mobile Pump Unit
For various applications with flows from 5 to 1.050 m3/h (20 to 4.600 USGpM).
Optional with Diesel engine or electrical drive.
The trailer can be delivered complete, as instant unit.
Aggregate also available with tarp cover or acoustical enclosure.

11. Tractor PTO driven Pump Aggregate
BÖRGER
Baseframe with connector and joining coupling for fitting to tractor or Unimog.
12. Pump for Road Tanker
Selfprimimg pump with conveying capacity up to 1.050 m3/h (4.600 USGpM).
Driven by auxiliary drive or hydraulic motor.

13. Pump with Open Hopper
Horizontally fitted pump with inlet hopper for high viscous but still flowable material.
14. Pump with Auger Feed Screw
Feeding hopper device with auger feed screw for non-flowable but still pumpable
products.
Auger feed screw driven by variable speed geared motor.

13
Monitoring Devices
Monitoring Devices
1. Thermal Dry Running Protection with Cover fitted Sensor
BÖRGER
Dry running protection with cover fitted temperature sensor.
Optional with control unit for switch cabinet.
2. Dry Running Protection with Flow Sensor
BÖRGER
The flow sensor installed in the suction pipe detects dry running for the drive to be
switched off.
Optional with control unit for switch cabinet.
Monitoring Devices
3. Electrical Overpressure Protection
BÖRGER
The pressure gauge with adjustable limit switch installed in the discharge pipe de-
tects overpressure for the drive to be switched off.
4. Mechanical Overpressure Protection, Valve with Bypass
The discharge pipe may be closed for short term without switch-off of the pump drive.
While the pressure line is closed the product is conveyed through the external over-
pressure valve and bypass system back to the suction side.
Monitoring Devices
5. VARIO-CAP
A reliable mechanical overpressure protection device, also for
reversible operation.
C Clearance
S Stroke
Pos. 1 Pump Casing
Pos. 2 Rotor
Pos. 3 Cover Frame
Pos. 4 Vario Membrane
Pos. 5 Spring Package
Pos. 6 Spindle
The forces resulting from the pressure produced in the pump are acting against the
forces of springs. As far as the spring load is higher, the cover is pressed to the pump
casing to ensure the usual performance of the pump. In case of raising pressure
above spring load the cover is moved away axially. The clearance then allows
pumped product to flow back from the pressure side to the suction side of the pump
which consequently reduces the performed volume. The maximal operating pressure
is limited by the forces of the springs, which are adjustable. In case of closed pres-
sure outlet the total volume flows back through the clearance between the conveying
elements and the pressed off cover. With the reduction of the back pressure the gap
closes and the performed volume rises.
The VARIO-CAP is sealed via an elastic diaphragm.
14
Specifications
Specification AL-Pumps
1 - 15 m3/h
...............................................pump
as Rotary Lobe Pump, horizontal fitted, not sensitive against dry running.
Driven by electrical gear motor.
Pump and drive fitted on common twist free baseframe (no folded plate), made from
galvanised steel, incl. elastic coupling and non sparking coupling guard.
System and fluid conditions:
Fluid: ...........................................
Solids content: ............................................%
Operating temperature: .............................................°C
Capacity: ............................................m3/h
Self priming: yes / no
Suction pressure: ............................................mWc
Discharge pressure: ............................................barg
Differential pressure: ............................................bar
Flanges: suction flange: DN.................
pressure flange: DN.................
Reversing operation: possible
Pump data:
Make: BÖRGER Tel. (49)2862/9103-20, Fax. (49)2862/9103-46
Type: .............................................
Design pressure: ..............................................bar
Shaft speed: ..............................................rpm (max. app. 550 rpm)
Required power: ..............................................kW
Selected power: ...............................................kW
Free ball entrance: .......................min. diam. 25 mm

Specification AL-Pumps
Design and Materials:
Pump casing: Blockcasing, casing from one piece only,

made of grey cast iron EN-GJL-250 (GG 25), surface hard,
protective plates at both faces, product-loaded parts,
incl. axial protective plates, changeable through the
pump casing without disassembling the pump and/or pipes
Service: suitable for MIP™, Maintenance in Place, simply by opening the

quick release cover with O-ring sealing
Bearings: one side double bearings, oil bath in block-casing, lateral drain plug
Lobe-form: dual-lobe rotors, non-wetted base core from EN-GJL-250 (GG 25),
entirely NBR-coated
Shafts: not wetted by pumped fluid, but oil lubricated
Shaft sealing: maintenance free single acting mechanical seals with common oil
quench for both seals (grease not allowed)
both seal faces Duronit V / Duronit V, identical design,
replaceable through pump casing
Sealing control: oil filled intermediate chamber in between gear and wetted end with
lateral drain plug, for quenching and monitoring the seals and for
lubricating the shaft-rotor-connections
Overpressure protection: Integrated overpressure relief valve (as option)
Drive: helical geared motor
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: ........................................IP 55
Isolation class: ........................................F
Protection: ............3 PTC Thermistors
Weight of the complete aggregate: kg
Dimensions of the compl. Aggregate: x x mm
Supply of pump aggregate as described before:
.....of Price per each:.................€ Total amount:......................€

Specification PL-Pumps
15-75 m3/h
...............................................pump
as Rotary Lobe Pump, horizontal fitted, not sensitive against dry running.
Driven by geared motor.
galvanised steel, incl. elastic coupling and coupling guard.
Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Flanges: suction flange: DN................
pressure flange: DN................
Pump data:
Type: .............................................

Specification PL-Pumps
Pump casing: Blockcasing, from one piece only,

protective plates at both faces, optional radial casing liners,
product-loaded parts, incl. axial and optional radial liners, replaceable
through the casing without disassembling the pump and/or pipes
Service: suitable for MIP™ Maintenance in Place, simply by opening the quick
release cover with O-ring sealing
Lobe-form: dual-lobe rotors, non-wetted base core from EN-GJL-250 (GG 25),
entirely NBR-coated, lobes readjustable: yes / no / as option
or helical screw lobe form for pulsation free operation (optional)
Shafts: not wetted by pumped fluid, but quench-oil lubricated
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55
Protection: ...........3 PTC Thermistors
Weight of the complete aggregate: kg Dimensions : x x mm

Specification CL-Pumps
30-150 m3/h
...............................................pump
as Rotary-Lobe-Pump, horizontal fitted, not sensitive against dry running.

Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Pump data:
Type: .............................................

Specification CL Pumps

Lobe-form: tri-lobe rotors with pushed-on quick replaceable rubber coated tips,
in helical screw design, core from EN-GJS-400 (GGG 40), tips NBR-
coated (tips replaceable without disassembling of pump and/or pipes)
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55
Weight of the complete aggregate: kg Dimensions: x x mm

Specification FL- and FLA-Pumps
60-400 m3/h
...............................................pump

Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Pump data:
Type: .............................................

Specification FL and FLA-Pumps

Lobe-form: tri-lobe rotors with pushed on quick replaceable rubber coated tips, in
linear or helical screw design, core from EN-GJS-400 (GGG 40), tips
NBR-coated (replaceable without disassembling of pump and/or pipes)
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55

Specification XL-Pumps
100 - 1050 m3/h
...............................................pump

Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Pump data:
Type: .............................................

Specification XL-Pumps

Lobe-form: dual-lobe rotors in screwed geometry with especially large sealing

face
for pulsation reduced operation, entirely NBR coated.
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55

Specification HAL-Multicrusher
up to 10 m3/h
Macerating unit for chopping solids in fluids
as dual shafted, low speed, high torque grinder, not sensitive against dry running.
Driven by electrical gear motor.
Complete with drive fitted on common twist free baseframe (no folded plate), made from
galvanised steel, incl. elastic coupling and non sparking coupling guard.
Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Inlet pressure: ............................................mWc
Flanges: inlet flange: DN.................
outlet flange: DN.................
Technical data:
Type: HAL 50
Shaft speed: ..............................................rpm

Specification HAL Multicrusher
Pump casing: in Block-construction, wetted casing from one piece only,

protective plates at both faces
all product-loaded parts, incl. axial protective plates, replaceable
through the casing without disassembling the machine and/or pipes
Service: suitable for MIP™, Maintenance in Place, simply by opening the

quick release cover with O-ring sealing
Cutting elements: cutting wheels and counter knifes 4 mm, hardened steel 1.2379
(easily replaceable without disassembling of machine and/or pipes)
replaceable through wetted casing
lubricating the shaft-connections
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: ........................................IP 55
Protection: ............3 PTC Thermistors
Weight of the complete aggregate: kg
Dimensions of the compl. Aggregate: x x mm
Supply of Multicrusher aggregate as described before:

Specification HPL Multicrusher
up to 60 m3/h
Macerating unit for chopping solids in fluids,
Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Technical data:
Type: HPL 200
Shaft speed: ..............................................rpm

Specification HPL Multicrusher
Wetted casing: in Block-construction, wetted casing from one piece only,

Maintenance: suitable for MIP™ Maintenance in Place, simply by opening the quick
Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55

Specification HCL Multicrusher
up to 120 m3/h
Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Technical data:
Type: HCL 390
Shaft speed: ..............................................rpm

Specification HCL Multicrusher

Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55

Specification HFL Multicrusher
up to 200 m3/h
Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Technical data:
Type: HFL 776
Shaft speed: ..............................................rpm

Specification HFL Multicrusher

Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55

Specification HLA Multicrusher
up to 310 m3/h
Fluid: ...........................................
Solids content: ............................................%
Capacity: ............................................m3/h
Technical data:
Type: HLA 1540
Shaft speed: ..............................................rpm

Specification HLA Multicrusher

Make: .....................................
Type: ......................................
Output power: .......................................kW
Output speed: .......................................rpm
Voltage: .......................................V
Frequency: ........................................Hz
Enclosure: .......................................IP 55

Specification Multichopper
Macerating Unit
Including debris collection area for non-cutable solids, in space saving Inline design , for fitting
to pipes.
Systems Condition:
Medium: …………………………
Solids Content: …………………………%
Viscosity: flowable
Operating Temperature: ……………………….°C
Specific Gravity: ………………………. kg/dm3
Throughput volume: ……………………….. m3/h
Inlet Pressure: ………………………..mWs
Flange Connections: Inlet: DN 150 PN 10
Outlet: DN 150 PN 10
Macerator Data:
Make: BÖRGER
Tel. +49 / 2862 9103-20 - Fax 9103-46
Type: Multichopper
Size and Type: ........................
Shaft Speed: .................... U/min

Required Power: ..................... kW
Selected Power: ..................... kW
Specification Multichopper
Design :
- 1 cutter plate
- 2 of knifeheads with each 3 knifes, adjustable from outside via one central screw
- 6 cuts per revolution
- Each knife can be used 4 times by simply reversing
- Easy and simply opening via quick release cover
- Flange connections: DN 150 PN 10/16
- Draining and cleaning port
Materials :
- Casing and cover from steel, painted

- Cutter casing: Steel 1.0037
- Cutter plate and knifes: Hardened steel 1.2379
- Shaft seal: Mechanical seal Duronit V with quench and optical control
- O-Rings: NBR
- Flange connections: Steel painted
Drive:
Drive: Parallel shaft geared motor

Make: ...................................
Type: ...................................
Power: ................................. kW
Shaft speed: ................................ U/min
Voltage: ................................ V
Frequency: 50 Hz
Enclosure: IP 55
Temperature class: F
Protection: 3 PTC Thermistors
Total weight of the aggregate: .................... kg
Dimensions of the aggregate (L x W x H): .......... x ......... x ........ mm
Aggregate to be delivered as described:
....... Units Price each: .............. € Price total: ..................... €

15
Inquiry Form and Brochures
Rotary Lobe Pump SENDER: __________________________________
Chopping Technology __________________________________
__________________________________
Börger GmbH
Benningsweg 24 Contact : __________________________________
46325 Borken-Weseke Telephone: __________________________________
Germany Fax: __________________________________
Date: __________________________________
INQUIRY FAX: +49 (0) 28 62 / 91 03 – 46

E-Mail: info@boerger-pumps.com
Please send more technical information about _______________________

Please call back to Tel.: ____________________________
Please visit us (upon appointment)
We ask for a free of cost, non obligatory quote:
_____ of BÖRGER Rotary Lobe Pump (s) / Multicrusher for:______________________________

Conv. Capacity: min:______m³/h max: ________ m³/h Duty Point:______m³/h
Head: ________ mWc Pressure: ________ bar
Self priming: ________ m Flooded: ________ m NPSH avail.:______ m
Fluid Temperature: ________ ºC Viscosity: ________ mPas/cP pH-Value:________
Spec. Gravity: ________ kg/m³ Solids: ________% Volume / Weight
Operating Time / Day: app.________ h Kind of Solids:__________________________________
Pipe Connections Suction: DN______ Suction Lenght:______ m total Discharge: DN______
Required Materials:_________________________________________________________________
Dry running Protection: No Yes Make:_________________________________
Overpressure Protection: No Yes Make:_________________________________
DRIVE: MOTOR DATA:
without Drive Voltage: __________V
Geared Motor
with Frequency Inverter
Variable Speed Geared Motor: Frequency: __________Hz
with Handwheel Adjustment
with Servomotor Ex-Proof: No
Hydraulic Motor Yes:___________
mobile Pump with:
Drive as Diesel Motor fitted on Car Trailer
Electric Motor Hand Trolley
OTHERS / REMARKS:_____________________________________________________________

Boerger Rotary Lobe Pump PDF

Uploaded by

Copyright:

Available Formats

Boerger Rotary Lobe Pump PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boerger Rotary Lobe Pump PDF

Uploaded by

Copyright:

Available Formats

Planning Information

Börger Rotary Lobe Pumps

FL and FLA Series

The Börger Chopping Technology The Börger Multicrusher

The Börger Multichopper

Accessories and Others Connection Flanges

Inquiry Form and Brochures 15

The parallel, 2-shaft design is

The displacement rotors are fitted on

The accurate Flow

The Timing Gear

One side Bearings

The Rotary Lobes

The Ease of Maintenance

The Fluid-filled Intermediate Chamber

• Numerous of pump ranges enable an exact adaptation to individual application.

• The compact design allows installation in space-limited situations.

• For abrasive products, dual-vane, readjustable rotors are available.

• Unlimited variations and applications.

Paper and Paper

Fish and Meat Processing

Fruit and Vegetables Processing

1. Bearing and Timing Gear

BLOCK-casing, machined with

Oversized self-aligning bearing, Cylinder roller bearing, permits

Timing gear with precisely made gear wheels

Any seal failures are indicated early by quench fluid overflow.

Timing gear Wetted pump chamber

Seal monitoring probe (optional)

Each pump casing is cast separately in one piece

Large direct inlet / outlet openings for continuous

One individual casing length for each pump size.

So a consequent MIP = Maintenance in Place is ensured.

A special innovation is the BOERGER MULTISEAL system, a specially developed radial

Mechanical Seal Gland Packing MULTISEAL

For abrasive products there are entirely elastomer

To convey extremely problematic fluids, i.e. solvents,

Fluids contaminated with solids are the ideal appli-

Although Rotary Lobe Pumps generate low pulsations,

A real innovation are the new BOERGER Optimum

The rotors are adopted to each individual pplication.

Maintenance friendly in perfection!

MIP = Maintenance in Place

Maintenance free additional shaft support

n=300 rpm n=450 rpm-1 p = max. 12 bar /174 (depending on model)

Measure above single flange [A] / Measure above flanges [B]

AL 25 DN 32 [mm] *DN 40 [mm] DN 50 [mm] DN 65 [mm] DN 80 [mm]

Dimensions may differ due to production reasons!

front side arrangement

overhead drive assembly

Drive Weight Dimensions

Dimensions may differ due to production reasons!

Measure above single flange [A] / Measure above flanges [B]

AL 50 DN 40 [mm] *DN 50 [mm] DN 65 [mm] DN 80 [mm] DN 100 [mm]

Dimensions may differ due to production reasons!

front side arrangement

overhead drive assembly

Drive Weight Dimensions

Dimensions may differ due to production reasons!

FL 776 DN 125 [mm] DN 150 [mm] DN 200 [mm]