AS/NZS 3008.1.

1:2017
AS/NZS 3008.1.1:2017

Australian/New Zealand Standard™

Electrical installations—Selection of
This is a free 7 page sample. Access the full version online.

cables

Part 1.1: Cables for alternating voltages

up to and including 0.6/1 kV—Typical
Australian installation conditions
 AS/NZS 3008.1.1:2017
This Joint Australian/New Zealand Standard was prepared by Joint Technical
Committee EL-001, Wiring Rules. It was approved on behalf of the Council of
Standards Australia on 11 January 2017 and by the New Zealand Standards
Approval Board on 17 November 2016.
This Standard was published on 2 February 2017.

The following are represented on Committee EL-001:

Australian Building Codes Board

Australian Industry Group
Communications, Electrical and Plumbing Union—Electrical Division
Consumers Federation of Australia
Electrical Contractors Association of New Zealand
Electrical Regulatory Authorities Council
Electrical Safety Organisation, New Zealand
ElectroComms and Energy Utilities Industries Skills Council
Energy Networks Association
Engineers Australia
This is a free 7 page sample. Access the full version online.

Institute of Electrical Inspectors

Master Electricians Australia
Ministry of Business, Innovation and Employment, New Zealand
National Electrical and Communications Association
National Electrical Switchboard Manufacturers Association
New Zealand Council of Elders
New Zealand Electrical Institute
New Zealand Manufacturers and Exporters Association
Trade and Investment, NSW

Keeping Standards up-to-date

Standards are living documents which reflect progress in science, technology and
systems. To maintain their currency, all Standards are periodically reviewed, and
new editions are published. Between editions, amendments may be issued.
Standards may also be withdrawn. It is important that readers assure themselves
they are using a current Standard, which should include any amendments which
may have been published since the Standard was purchased.
Detailed information about joint Australian/New Zealand Standards can be found by
visiting the Standards Web Shop at www.saiglobal.com or Standards New Zealand
web site at www.standards.govt.nz and looking up the relevant Standard in the on-
line catalogue.
For more frequent listings or notification of revisions, amendments and
withdrawals, Standards Australia and Standards New Zealand offer a number of
update options. For information about these services, users should contact their
respective national Standards organization.
We also welcome suggestions for improvement in our Standards, and especially
encourage readers to notify us immediately of any apparent inaccuracies or
ambiguities. Please address your comments to the Chief Executive of Standards
Australia or the New Zealand Standards Executive at the address shown on the back
cover.

This Standard was issued in draft form for comment as DR AS/NZS 3008.1.1:2015.
 AS/NZS 3008.1.1:2017

Australian/New Zealand Standard™

Electrical installations—Selection of
This is a free 7 page sample. Access the full version online.

cables

Part 1.1: Cables for alternating voltages

up to and including 0.6/1 kV—Typical
Australian installation conditions

Originated in Australia as AS 3008.1—1984.

Originated in New Zealand as AS/NZS 3008.1.1:1998.
Previous edition 2009.
This edition 2017.

COPYRIGHT
© Standards Australia Limited/Standards New Zealand
All rights are reserved. No part of this work may be reproduced or copied in any form or by
any means, electronic or mechanical, including photocopying, without the written
permission of the publisher, unless otherwise permitted under the Copyright Act 1968
(Australia) or the Copyright Act 1994 (New Zealand).
Jointly published by SAI Global Limited under licence from Standards Australia Limited,
GPO Box 476, Sydney, NSW 2001 and by Standards New Zealand, PO Box 1473,
Wellington 6011.

ISBN 978 1 76035 658 3

 AS/NZS 3008.1.1:2017 2

PREFACE
This Standard was prepared by the Joint Standards Australia / Standards New Zealand
Committee EL-001, Wiring Rules, to supersede AS/NZS 3008.1.1:2009, Electrical
installations—Selection of cables, Part 1.1: Cables for alternating voltages up to and
including 0.6/1 kV—Typical Australian installation conditions.
This Standard is applicable to Australian installation conditions where the nominal ambient
air and soil temperatures are 40°C and 25°C, respectively. AS/NZS 3008.1.2 is applicable
to New Zealand installation conditions where the nominal air and soil temperatures are
30°C and 15°C respectively. Each Part is a complete Standard and requires no reference to
the other.
AS/NZS 3008.1.2 deals with cables for use with alternating voltages over 1 kV.
The objective of this Standard is to specify current-carrying capacity, voltage drop and
short-circuit temperature rise of cables, to provide a method of selection for those types of
electric cables and methods of installation that are in common use at working voltages up to
and including 0.6/1 kV at 50 Hz a.c.
This is a free 7 page sample. Access the full version online.

This Standard differs from the 2009 edition and its subsequent amendment as follows:
(a) Economic optimization for cable selection recommendations, including a new
example in Appendix A.
(b) A new definition for Circuit.
(c) Cable core cross sections have been updated for the following:
(i) Figure 1.
(ii) Table 3(1).
(iii) Table 3(2).
(iv) Table 3(3).
(v) Table 3(4).
(vi) Table 10.
(vii) Table 11.
(viii) Table 12.
(ix) Table 13.
(x) Table 14.
(xi) Table 15.
(xii) Table 17.
(xiii) Table 26(2).
(d) New notes to Tables 30, 31, 40, 41, 43, 44, 46, 47, 50 and 51 have been included.
(e) Changes to derating factors in Table 23.
(f) Circuit recommendations for low magnetic fields added to Appendix D.
In the preparation of this Standard, reference was made to IEC 60287 and acknowledgement
is made of the assistance received from that source.
Statements expressed in mandatory terms in notes to tables and figures are deemed to be
requirements of this Standard.
 3 AS/NZS 3008.1.1:2017

The term ‘informative’ has been used in this Standard to define the application of the
appendix to which it applies. An ‘informative’ appendix is only for information and
guidance.
This is a free 7 page sample. Access the full version online.
 AS/NZS 3008.1.1:2017 4

CONTENTS

Page

SECTION 1 SCOPE AND APPLICATION

1.1 SCOPE ......................................................................................................................... 6
1.2 APPLICATION ........................................................................................................... 6
1.3 ALTERNATIVE SPECIFICATIONS .......................................................................... 7
1.4 REFERENCED AND RELATED DOCUMENTS ....................................................... 7
1.5 DEFINITIONS............................................................................................................. 8

SECTION 2 CABLE SELECTION PROCEDURE

2.1 GENERAL ................................................................................................................. 10
2.2 SELECTION PROCESS ............................................................................................ 10
2.3 DETERMINATION OF MINIMUM CABLE SIZE BASED ON
CURRENT-CARRYING CAPACITY CONSIDERATIONS .................................... 10
2.4 DETERMINATION OF MINIMUM CABLE SIZE BASED ON
This is a free 7 page sample. Access the full version online.

VOLTAGE DROP CONSIDERATIONS................................................................... 11

2.5 DETERMINATION OF MINIMUM CABLE SIZE BASED ON THE
SHORT-CIRCUIT TEMPERATURE CONSIDERATIONS ..................................... 12
2.6 DETERMINATION OF CABLE SIZE BASED ON THE ECONOMIIC
OPTIMIZATION CONSIDERATIONS (OPTIONAL) ............................................. 12

SECTION 3 CURRENT-CARRYING CAPACITY

3.1 RATINGS .................................................................................................................. 13
3.2 TYPES OF CONDUCTORS ...................................................................................... 13
3.3 TYPES OF CABLE ................................................................................................... 15
3.4 INSTALLATION CONDITIONS .............................................................................. 17
3.5 EXTERNAL INFLUENCES ON CABLES ............................................................... 20

SECTION 4 VOLTAGE DROP

4.1 GENERAL ................................................................................................................. 91
4.2 DETERMINATION OF VOLTAGE DROP FROM MILLIVOLTS
PER AMPERE METRE ............................................................................................. 91
4.3 DETERMINATION OF VOLTAGE DROP FROM CIRCUIT IMPEDANCE .......... 92
4.4 DETERMINATION OF VOLTAGE DROP FROM CABLE OPERATING
TEMPERATURE ...................................................................................................... 94
4.5 DETERMINATION OF VOLTAGE DROP FROM LOAD POWER FACTOR ........ 94
4.6 DETERMINATION OF VOLTAGE DROP IN UNBALANCED
MULTIPHASE CIRCUITS ....................................................................................... 97

SECTION 5 SHORT-CIRCUIT PERFORMANCE

5.1 GENERAL ............................................................................................................... 120
5.2 FACTORS GOVERNING THE APPLICATION OF
THE TEMPERATURE LIMITS .............................................................................. 120
5.3 CALCULATION OF PERMISSIBLE SHORT-CIRCUIT CURRENTS .................. 121
5.4 INFLUENCE OF METHOD OF INSTALLATION................................................. 122
5.5 MAXIMUM PERMISSIBLE SHORT-CIRCUIT TEMPERATURES ..................... 122
 5 AS/NZS 3008.1.1:2017

Page

APPENDICES
A EXAMPLES OF THE SELECTION OF CABLES TO SATISFY
CURRENT-CARRYING CAPACITY, VOLTAGE DROP
AND SHORT-CIRCUIT PERFORMANCE REQUIREMENTS ............................. 124
B LIST OF TABLES ................................................................................................... 138
C EXAMPLES OF THE APPLICATION OF REDUCTION FACTORS
FOR HARMONIC CURRENTS .............................................................................. 142
D RECOMMENDED CIRCUIT CONFIGURATIONS FOR THE INSTALLATION
OF SINGLE-CORE CABLES IN PARALLEL........................................................ 143
This is a free 7 page sample. Access the full version online.
 This is a free preview. Purchase the entire publication at the link below:

AS/NZS 3008.1.1:2017 Electrical installations -

Selection of cables - Cables for alternating
voltages up to and including 0.6/1 kV - Typical
Australian installation conditions
This is a free 7 page sample. Access the full version online.

Looking for additional Standards? Visit SAI Global Infostore

Subscribe to our Free Newsletters
Do you need to Manage Standards Collections Online?
Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation
Do you want to know when a Standard has changed?
Create safe work processes for the workplace with our Safe Work Method Statements

Learn about other SAI Global Services:

LOGICOM Military Parts and Supplier Database

Metals Infobase Database of Metal Grades, Standards and Manufacturers
Materials Infobase Database of Materials, Standards and Suppliers
Database of European Law, CELEX and Court Decisions

Need to speak with a Customer Service Representative - Contact Us