support@elmeasure.

com
Ph: +91 80 32904489

A+ ADC A+ VDC

AMPS DC VOLTS DC

K K

MINUS MINUS

PRG PRG

HO & Unit -1 : Unit -2 : ALPHA+ ALPHA+

47-P, Hardware Park, KIADB, Goutham Garden, No.4,
Huvinayakanahalli Bengaluru - 562149 Veerapandi, Coimbatore - 641 019
Karnataka INDIA. Tamilnadu INDIA
PROGRAMMING GUIDE
Sales Offices :
BENGALURU CHENNAI COIMBATORE MUMBAI DELHI HYDERABAD USA UAE ALPHA+ DC ( VDC & ADC )
PG/APDC/V4/0217 www.elmeasure.com

1. FEATURES
Universal Auxiliary supply (80-300V AC/DC). 5 Press RIGHT key to
Parameters V(VDC) & A(ADC). set PT Primary/ CT
Primary value First digit blinking can be
1 row 4 digit display. edited using
User configurable (Editable) password. DOWN key.
Auto-scaling of kilo decimal point.
6 Press RIGHT key to
accept the edited value
2. WIRING DIAGRAM - Alpha Plus DC (VDC & ADC) Second digit blinking, can
for first digit.
be edited using DOWN key.
Press RIGHT key to accept
80-300V AC/DC
B A the edited value. Continue
40-300V AC/DC Optional
the same method till fourth
digit.

INPUT VDC 7 Press RIGHT key to Eg: To set 61.00KV

DIGITAL OUTPUT

RS 485
accept the value. Set first four digits (6100)
COM Decimal point blinking. Can
as explained above keep
D1 be set at appropriate
pressing DOWN key to
D2 location using DOWN key.
place decimal point at
Ascertain the correct scale
INPUT ADC appropriate location
(Kilo) is selected. Kilo is
represented by Letter K.
Press RIGHT key to accept
the edited value.
SOURCE

8 Press DOWN key OFFS in case of ADC.

C.1.S.U in case of VDC
OFFS / C.1.S.U (Offset/
SHUNT Channel 1 Shunt value)

LOAD

3. KEY FUNCTIONS
9 Press RIGHT key to For ADC:
Key In SET (Programming) mode In RUN (Measurement) mode view the option Options-0.t.FS (Zero to Full
0.t.FS for ADC
Right/UP To select the value and accept the value To scroll pages to look at different scale) & 4.t.FS (4mA to Full
(it act as a Right key in programming parameters. 75.00 for VDC
scale).
mode) (Zero to Full scale/ 75mV)
For VDC:
DOWN To edit the value/system type down- To scroll pages to look at different Range : 50mV to 75mV
ward in edit mode and scroll through parameters The options can be changed
the parameters. by pressing DOWN key.
10 Press DOWN key
4. ENTERING CONFIGURATION (SETUP) MODE
Defines Digital output
Step Actions Display Reads Range/Options/Comments 1 Parameter)
1 Press RIGHT & first digit 11 Press RIGHT key to
DOWN keys together to “0” blinking view digital output
enter SETUP options
2 Press DOWN key to If any other 12 Press RIGHT key to go Options:
decrement the first digit password is already set Parameter
for options For VDC: dSbL/ Un.V
to “9” sequentially come with “1” blinking. press RIGHT and DOWN key blinks. eg: Un.V (Under Volts) (Under Volts) / OU.V(Over
to digit “1”. to reach the right password (For VDC)/ Un.A (Under Amps) Volts)
3 Press DOWN key (PT Primary) (For ADC). Blinking parameter For ADC: dSbL/ Un.A
Only for VDC) can be edited using DOWN (Under Amps) / OU.A
(CT Primary) key. Press RIGHT key to accept (Over Amps).
(Only for ADC) the edited option.
4 Press RIGHT key to Range:0.100 to 999.9KV 13 Press DOWN key Defines the threshold limit
default/factory
view PT primary value / set (for VDC) (for VDC)
CT primary value Range:0.100 to 999.9kA 14 Press the RIGHT Key
default/factory
set (for ADC) (for ADC) to view the value
(Default threshold value)
 15 Press again RIGHT Range: 1.000 to 999.9K 5. The List of parameters can be configured and the range is given
key to edit the value eg: 60.00 First
digit blinking can be edited below
using DOWN key. Press RIGHT Default
Sl.No. Parameter setup Range / Options
key to accept the edited value.
Continue the same method 1 PT Primary ( P.Prı) (Only for VDC) 48.00 0.100 to 999.9KV (Only for VDC)
till fourth digit. Decimal point
blinking can be set at 2 CT Primary (C.Prı) (Only for ADC) 75.00 0.100 to 999.9KA (Only for ADC)
appropriate location using 3 Offset(OFFS) - for ADC 0.t.FS/ 0.t.FS/4.t.FS - for ADC
DOWN key and again press C.1.S.V - for VDC 75.00 50mV to 75mV - for VDC
RIGHT key to accept.
16 Press DOWN key 4 1st Digital Output parameter dSbL For VDC - Over V, Under V & dSbL
(dO1.P) For ADC - Over A, Under A & dSbL
(Defines Digital output 2)
17 Press RIGHT key to 5 1st Digital Output threshold Value 60.00 1.000 to 999.9K
view digital output options (dO1.t)
18 Press RIGHT key to go Options : 6 2nd Digital Output parameter dSbL For VDC - Over V, Under V & dSbL
for options For VDC: dSbL/ Un.V (Under (dO2.P) For ADC - Over A, Under A & dSbL
Parameter blinks. eg: Un.V
Volts) / OU.V(Over Volts)
(Under Volts) (For VDC)/ 7
For ADC: dSbL/ Un.A (Under 2nd Digital Output threshold Value 24.00 1.000 to 999.9K
Un.A (Under Amps)(For ADC)
Amps) / OU.A(Over Amps) (dO2.t)
blinking parameter can
be edited using DOWN key. 8 Digital Delay 3.000 1.000 to 180.0 Sec
Press RIGHT key to accept
the edited option. 9 Baud rate (bAUd) 9600 1200 to 19.2k
19 Press DOWN key Defines the threshold limit 10 Parity (Prty) Even 1.000 to 180.0 Sec

20 Press the RIGHT Key to 11 Device Id (dEV.Id) 1.000 1.000 to 247.0

(Default
view value 12 Password (PWd) 1000 1000 to 9999
threshold value)

21 Press again RIGHT key Range: 1.000 to 999.9K 6. LED INDICATION

to edit the value eg: 24.00 First digit blinking LED Status Meaning LED Status Meaning LED Status Meaning
can be edited using DOWN
key. Press RIGHT key to - Minus Communication K Kilo
accept the edited value.
Continue the same method 7. Mechanical Specification:
till fourth digit.
Decimal point blinking can Dimension Bezel: Panel Cutout:
90+2 +2
be set at appropriate 96 x 96 mm (Depth 50mm behind Bezel) -0 x 90 -0 mm
location using DOWN key
and again press RIGHT key
to accept.
22 Press DOWN key (Digital Delay) 90 mm Panel

23 Press RIGHT Key to view (Default)

90 mm

the value
First digit blinking can be
edited using DOWN key.
Press RIGHT key to accept
the edited value. Continue
Clamp
the same method till fourth
digit. . Decimal point
blinking can be set at
appropriate location using
DOWN key.
24 Press DOWN key (baud rate) Defines the baud rate.
communication speed.
25 Press RIGHT key to default /factory Option:1200,
view value set 2400, 4800, 9600, 19.20k.
Press DOWN & RIGHT key
to set the required value.

26 Press DOWN key Internal communication

error check
27 Press RIGHT key to default /factory EUEn (even)/odd
view option set (odd)/no (no parity) The
options can be changed by
pressing DOWN key. Press
RIGHT key to accept the
edited option.
28 Press DOWN key (device ID) Defines the (ID)
communications
29 Press RIGHT key to view Identification
the value number (1 to 247). Press
DOWN & RIGHT key to set
the required value.
30 Press DOWN key (Password user CAUTION:
definable). memorize the Password.
Use the same Password for
next time. Instruments will
reject other Passwords.
31 Press RIGHT key to view Range: 1000-9999.
password CAUTION: Password can be
reset only at the factory.
Press DOWN & RIGHT key to
set the required value.
32 Press DOWN key blinking. If “n”(no) is selected then
Meter enters into RUN mode
33 Press RIGHT key to store Display returns to Run mode. without affecting any edited
the changes Values in the setup
Once the required parameter is programmed press the DOWN key continuously till it
reaches SAVE page directly.