QUESTION BANK FOR CNC TECHNOLOGY (CP01) ONLINE

EXAMINATION: IV SEMESTER

UNIT – I INTRODUCTION TO COMPUTER NUMERICAL CONTROL

1) The diametrical axis in CNC lathe is ___________

a) +Z
b)X
c)U
d)Y

2) In a 3 Axis VMC the spindle axis is ___________

a) X
b)Y
c)U
d)Z

3) Programme is controlled with separate dedicated computer in ______

a) NC
b) CNC
c) DNC
d) TNC

4)CNC machines are most suitable for _______

a. Small batch production

b. Large batch production
c. Very small batch production
d. Small to medium sized batch production

5) For increasing the productivity CNC system can be interfaced

a. CAD/ CAM
b. DNC
c. FMS
d. All of the above

6) _______________ language is most commonly used in computer aided part

programming

a. C
b. APT
c. Basic
d. None of the above

7) The spindle of three –axis or two –axis CNC machine is generally designated as
which axis?

a. Z
b. X
c. C
d. None of the above

8) ______ is the disadvantage of the CNC machine tools

a)Higher Investment cost

b)Higher Maintenance cost
c)Trained Personnels
d) All the above

9) VMC stands for ________

a)Vertical axis machinining controller

b)Vertical axis machine controller
c)Vertical axis machining centre
d) None

10) HMC stands for ________

a)Horizontal Axis machining Centre

b)Horizontal Axis Machining Controller
c)Horizontal Axis Machine controller
d) None

11) The spindle of three axis or two axis CNC machine is generally designated as
which axis?

a. Z
b. X
c. C
d. None of the above

12. NC Stands for _________.

a. Numerical Control
b. Numerical Component
c. Nominal Circuit
d. Numerical Circuit

13. CNC Stands for ________.

a. Computer Numerical Control

b. Copying Numerical Control
c. Computer Numerical Circuit
d. Component Numerical Control

14. DNC Stands For _________.

a. Database Numerical control

b. Dimension Numerical Control
c. Direct Numerical Control
d. Default Numerical Control

UNIT II-CNC HARDWARE BASICS:

15) To execute CNC drilling ___________ control system is used by the controller

a) Straight line
b)Contour
c)Point to point
d)Contour 3D

16)In a stepper motor the typical resolution for one step is_____ Degree

a) 1.8
b) 3.6
c)36
d) None

17) The CNC guide way are coated with _________ for antifriction purpose
 a) ABS
b) PS
c) FE
d) PTFE

18) The main difference between open loop and closed loop is ________

a) ATC
b) APC
c) Feedback
d) Tool length

19) A 3 Axis numerical controlled VMC is an example of _________

a) Point to Point
b) Straight line
c) Contouring
d) None

20) Tachogenerator is a ______

a) Position element
b) Feedback element
c) Cutting Tool
d) power element

21) To Achieve Quick start and stop precisely in CNC machine tools ___________ are
used as prime movers

a) Guide Ways
b) Slide Ways
c) Servo motors
d)Encoders

22) The recirculating ball screw and nut arrangement in CNC machine tools is ____

a) Feed back device

b) Prime mover
c) Lubrication system
d) Friction Reducing Element

23) Micro stepper motors are capable of _______ micro steps per revolution

a) 2000
b) 200000
c) 25000
d) 200

24) CNC Bed is made of ____________

a. Cast steel
b. Cast Iron
c. Alloy steel
d. None of the above

25) The general characteristic of a CNC Machine structure is _____

a) Low stiffness & high weight

b) High weight & high stiffness
c) Low weight & Low stiffness
d) High stiffness & Low weight

26) CNC spindle is made up of _______ material.

 a. Carbon steel forging
b. Cast iron
c. EN 31
d. None of the above

27) Cross slide of CNC lathe are lined with material

a. Steel
b. Rubber
C. Turcite
d. Aluminum

28. Which is the most versatile control system ___________?

a. Point to Point
b. Straight Cut
c. Contouring
d. None.

29. Expand PWM ________.

a. Pulse Width Modulated

b. Pulse Wide Modulated
c. Pulse Width mode
d. none

30. Linear & Angular position measuring transducer works on ______ principle.

a. Ohm’s Law
b. Photo Electric Principle
c. Planks Law
d. none

31. Application of Point to Point control system is ________.

a. Milling
b. Turning
c. Grinding
d. Drilling

32. The function of photo cell or photo diode is ______.

a. Gives output voltage based on the intensity of light falling on it

b. Senses the light & dark areas.
c. Both A & B
d. None
33. PTFE stands for ________.

a. Poly tetra fluro ethane

b. Poly tetra fluro ethylene
c. Penta tetra fluro ethylene
d. Poly tetra fluro methane

34. In Hydrostatic Slide ways, _________ is used as medium to reduce friction and
wear.

a. Air
b. Oil
c. Both A & B
d. None of the above
35. The design of slide ways in a CNC Machine tool should.

a. Reduce friction
b. Reduce wear
 c. Improve smoothness of the drive
d. All the above

UNIT – III – CNC TOOLING

36) ATC stands for __________

a) Automatic turret changer

b) Automatic tool changer
c) Advanced turret changer
d) Automatic technical chart

37) In HSS the major alloying elements which provide hardness is _______ & _____

a) Tungsten & Carbon

b) Tungsten & Molybdenum
c) Iron & Carbon
d) Chromium & Carbon

38) _________ process is used to convert carbide tool tips to coated carbide tips

a) PVD
B) CVD
c) TNR
d) CRC

39) APC stands for ______________

a) Automatic production cycle

b) Automatic Pallet Changer
c) Automatic Pallet Collector
d) Automatic Pallet Cycle

40) For more than one machine bed in a CNC mill, the following salient feature is
needed_______

a) ATC
b) APC
c) APT
d) scanning unit

41) Unit for cutting speed is ________

a) mm/rev
b) m/min
c) rpm
d) rev/mm

42) Stellite is one of the ____________

a) CNC controller
b) tool material
c) CNC hardware
d) software

43) To Increase the Cutting performance of HSS ________ Process is done

a) CVD
b) PVD
c) Carbide Coating
d) None
 44) The Main contributor to vibration during cutting is ___________

a) Axial Force
c) Radial force
c) Tangential Force
d) None

45) Table Feed in the same direction of Cutter rotation is called ________

a) Down Milling
b) Up milling
c) Complex Milling
d) Radius Milling

46) Table feed in the opposite direction of cutter rotation is called __________

a) Convex Milling
b) Form milling
c) Up milling
d) Down Milling

47) TNMG 22 04 08 in this ISO coding of Carbide insert “T” indicates

a) Clearance angle
b) Cutting edge length
c) Insert Shape
d) Nose radiu

48) TNR Stands for_________

a) Tool Nose radius

b) Tool neutral Radius
c) Total Nose radius
d) None

49) “CNMG 22 04 08” in this tool insert specification “22” stands for _______

a) Nose radius
b) Tip Dia
c) Insert thickness
d) Cutting Edge length

50) “CNMG 24 04 08” in this tool insert specification “04” stands for ____

a) Nose radius
b) Tip Dia
c) Insert Thickness
d) Cutting Edge Length

51) CNMG 120408 in carbide inserts

Letter M indicate ______

a. Insert shape
b. Insert clearance angle
c. Tolerance
d. Insert
52) CNMG 120408 in carbide inserts

Letter G indicate ______

a. Insert clearance angle

b. Tolerance
c. Insert type
 d. Insert size
53)In 18:4:1 HSS Tungsten percentage

a. 4%
b. 18%
c. 1%
d. 20%

54) In the ISO designation of Tool holder

P S R N R 16 16 H 12 in this , select the meaning of P

a. Insert size
b. Clearance angle
c. Types of clamping
d. Shank height

55) In the ISO designation of Tool holder

P S R N R 16 16 H 12 in this , select the meaning of H

a. Insert size
b. Shank height
c. Tool length
d. None of the above
56) In the ISO designation of Tool holder

P S R N R 16 16 H 12 in this, select the meaning of 12

a. Insert size
b. Tool length
c. style of toolholder
d. Types of clamping

57) “PCLNR 16 16 H09” in this specification of Tool Holder “P” Indicates __________

a)Shank height
b)Shank Width
c)Tool length
d)Clamping system

58) “SCLNR 16 16 H 09” in this ISO specification of Tool Holder “09” Indicates
_________

a) Cutting Edge Length

b) Shank Weight
c) Shank Height
d) Tool length

59) “SCLNR 16 16 H 09” in this ISO specification of Tool Holder letter “C” designates

a) Clamping Sytem
b) Insert shape
c) Holding Method
d) Shank Height
60) “SCLNR 16 16 H 09” in this ISO Specification of Tool Holder letter “N” designates
about

a)Cutting edge Length

b) Shank Width
c) Shank Length
d) Insert Clearance Angle
61) HSS retain their hardness upto ____ temperature

a)1800°C
b)1400°C
c)200°C
d)900°C

62) The basic ingredient of most carbide tools is _____

a)Chromium
b)Tungsten Carbide
c)Venadium
d)Molybdenum

63) Cermets means ____

a)Ceramic materials
b) Cermaics + Metals
c) Ceramics
d) All the above

64) To reduce the job setting time _______ feature is used

a)APC
b) Encoder
c)ATC
d)None

65)Tantalum carbide + Nickel is called as _____

a)Stellite
b)Cermets
c)Coated Carbides
d) None

66) For very low cutting speed _______ can be used as a cutting tool material

a)HSS
b)Stellite
c)Cermaics
d) Carbon Steels

67) Select the Cutting tool material of very high cutting speed ______

a)HSS
b) Diamond
c) Cermets
d)Stellite

68. In C Shape inserts, the included angle is _____.

a. 35°
b. 45°
c. 55°
d. 80°

69. In CNMG indexable type inserts, the letter N stands for _________.

a. Insert shape
b. Clearance angle
c. Tolerance
d. Insert type
70. In TNMG 22 04 08, 08 indicate ______.

a. Insert type
b. Insert shape
c. Insert thickness
 d. Nose radius.

UNIT – IV CNC MACHINE TOOLS AND CONTROL SYSTEMS

71) HSM stands for___________

a) Heavy speed machines

b) High stability machines
c) High speed machining
d) None

72) The measuring unit of CNC machine tools is ___________

a) MCU
b) ATC
c)APC
d) Touch trigger probes

73) In General _______ rpm is considered for the start point of rotational speed of
spindle in HSM

a)2000
b) 20000
c)8000
d) None

74) Dry run is used to______

a. Check CNC programme

b. Reduce machining time
c. Programme communication
d. None of the above

75) MDI in CNC stands for ______

a) Mechanical Data Input

b) Manual Data Integration
c) Manual Degree Input
d) Manual Data Input

76) To Drive the Axis as per part programme _________ is used in CNC machine tools

a) Feed back devices

b) Gear Drive
c) Feed drives
d) None

77) Which one of the following is related to Feed drive of CNC machine tools

a)DC Servo Motor

b) ATC
c)APC
d) ATC and APC

78) Select the Friction reducing element in CNC machine tools

a) Spindle drive with rollers

b) Recirculating ball and Nut
c) LM rail with ball retainer
d) All the above

79) ________ mode will be used when the memory space availability is less in CNC
controller
a) Auto
b) MDI
c) Jog
d) Drip Feed

80) To enter and modify the programme in CNC controller manually _____ mode is
used

a)Jog
b)Edit
c)MDI
d) None

81) To send all the Axis of the CNC machine to home position ______ mode is used

a)Reference
b)Edit
c)Jog
d)Teaching

82) To execute the machining _____ mode is used in CNC machine tools

a)Edit
b)Auto
c)Jog
d)None

83) ______ is the controller used in CNC machine tools

a)Siemens
b)Fanuc
c)Haas
d) All the above

84) MCU Stands for _______

a)Modular Control Unit

b)Modular control system
c)Machine control uses
d) Machine control Unit

85) The grid plate in a CNC machine tools is ________

a)Tool Holding
b)Work Holding
c)Feedback device
d)None

86) The Primary drawback of Open loop system is _____

a)No DNC
b) No feedback
c)No ATC
d)None

87) Point to Point controls system is used in CNC ___________

a)Drilling
b)Boring
c)Reaming
d)All the above
88) Straight Line control system is used in CNC __________

a)Face Milling
b)Pocket Milling
c)Step Turning
d) All the above

89. The function of machine control unit is _________.

a. Performs operation on machine on machine tool

b. Prepares the part programme
c. Reads the program & Converts into machine language & sends to
Machine tool
d. None of the above
90. What is the use of single block switch ON/OFF in control panel?

a. Part programming is executed automatically & continuously

b. Part program is executed Block – wise
c. To skip the blocks
d. None

91. MPG stands for ________.

a. Manual Power Generator

b. Manual Pulse Generator
c. Machine Pulse Generator
d. Manual Program Generator
92. VMC Stands for ______.

a. Vertical Manufacturing Centre

b. Vertical Machining Co ordinate
c. Vertical Machining centre
d. none
93. HMC Stands for ______.

a. Horizontal Manufacturing Centre

b. Horizontal Machining Co ordinate
c. Horizontal Machining centre
d. none

UNIT – V - CNC PROGRAMMING

94) The code G90 stands for __________

a) Tool Change
b) optional stop
c) Programme end
d) Absolute Co-oridnate system

95) The code G91 Stands for ___________

a) Coolant off
b) Coolant ON
c) Incremental Coordinate system
d) Thread Cutting Cycle

96) The symbol for skip function is ___________

a) ( )
b)%
c) #
d) /

97) The code G40 in milling stands for _________

a) CRC left
b) CRC Right
c) CRC cancel
d) Feed

98) The combination of address code and data is called ________of a programme

a) block
b)line
c)word
d)skip

99) __________ code is used to specify the function subprogramme call

a) G98
b) F98
c) M98
d) M99

100) ___________ code is used to specify the tool change function

a) M09
b)M06
c) M60
d) G28

101) For Dwell command the preparatory function is _________

a)G05
b) G02
c) G03
d) G04

102) Dry run is used to _____________

a) Check CNC Programme

b) Reduce machining time
c) Programme communication
d) None

103) In which of the following function feed is not required to specify

a) G01
b) G02
c) G03
d) G00

104) The reference will change continuously in ________ co-ordinate system

a) Absolute
b)Polar
c) Incremental
d) None

105) To stop the spindle of CNC machine tools ________ Miscellaneous function is
used

a) M96
b) M90
c) G05
 d) M05

106) Tool length offset value is stored in letter ___

a) G
b) Z
c) H
d) U

107) The “G” code used for CRC right is ___________

a) G40
b) G41
c) G42
d) G43

108) The “G” code used for CRC left is ____________

a) G40
b) G41
c) G42
d) G43

109) “N10 G01 X100 Y100” In this part programming line N10 stands for_____

a) Feed
b) Sequence No
c)Programme No
d)Tool No

110) G00 is used for _________

a. Linear interpolation
b. Rapid positioning
c. Zero return
d. Circular interpolation

111) G20 preparatory function used for ________

a. Inch input
b. Metric input
c. MKS input
d. None of the above

112) G21 preparatory function used for ________

a. Inch input
b. Metric input
C .MKS input
d. None of the above

113) G98 preparatory function used for

a. Feed per minute

b. Feed per revolution
c. Feed in mm
d. None of the above

114). M00 miscellaneous function used for ______

a. Temporary program stop

b. Optional stop
c. Program end
d. Spindle stop
115) In Which type of the following motors mechanical commutation is
avoided_________

a)DC Servo Motor

b)Stepper Motor
c) Brushless DC Servo Motor
d) Micro Stepper Motor

116) _________ Miscellaneous function is used chuck unclamp.

a. M10
b. M11
c. M16
d. M18

117) In the programming letter I is used for ________

a Incremental dimension in X axis during circular interpolation

a Incremental dimension Y axis during circular interpolation
a Incremental dimension in Z axis during circular interpolation
a None of the above

118) In the programming letter “O” is used for _______

a. Program number
b. Feed function
c. Speed function
d. Tool function
119) In the program letter “T” used for_____

a. Program number
b. Feed function
c. Speed function
d. Tool function

120). In the program letter “F” is used for_______

a. Program number
b. Feed function
c. Speed function
d. Tool function
121) S1000 M03 in this block M03 is used for

a. Spindle clockwise rotation

b. Spindle counter clockwise rotation
c. Spindle orientation
d. None of the above
122) In part programming address I,J,K are uses as

a. additional axes motion commands

b. Co-ordinate axis motion commands
c. Co-ordinate values of arc centre
d. Motion code

123) Length Offset are specified by

a. D
b. H
c. M
d. P
124) Sequence number is specified

a. In the beginning of a block

 b. At the end of a block
c. In the middle of a block
d. To show the end of program

125) In the ___________ system co-ordinates of point are always referred with
reference to same datum.

b. Absolute co-ordinate system

c. Incremental co-ordinate system
d. World co-ordinate system
e. None of the above

126) In the ________ system co-ordinates of any points are calculated with reference
to previous point.

a. Absolute co-ordinate system

b. Incremental co-ordinate system
c. User co-ordinate system
dNone of the above

127) In the programming letter J is used for ________

a. Incremental dimension Y axis during circular interpolation

b. Incremental dimension in Z axis during circular interpolation
c. Incremental dimension in X axis during circular interpolation
d. None of the above

128) In the programming letter K is used for ________

a. Incremental dimension Y axis during circular interpolation

b. Incremental dimension in Z axis during circular interpolation
c. Incremental dimension in X axis during circular interpolation
d. None of the above

129) G letter used for to specify ______

a. Preparatory function
b. Sequence number
c. Feed
d. None of the above

130) G00 X 70 Z-10 In this block, which is called DATA.

a. 00 70 -10
b. G X Z
c. G00 X 70 Z-10
d None of the above

131) In the CNC program Letter “S” is used to specify _______

a. Speed function
b. Tool function
c. Feed function
d. chamfering amount.

132) In the CNC program letter “ R” is used to specify ______

a. Radius of arc, Retraction amount.

b. Speed function
c. Feed function
d Incremental dimension

133) A set of Operations which is repeated regularly in the same sequence

 _________

a. Cycle
b. Contour
c. Offset
d. dwell

134) Which one of the following codes fall into motion group commands

a)G18
b)G17
c) G01
d)G70

135) _________ Preparatory function is used for the selection of XZ plane in a 3 Axis
VMC

a) G17
b) G18
c) G21
d) None

136) In a 3 axis VMC for the selection of XY Plane ________ code is used

a) G21
b) G18
c) G20
d) G17

137) In a 3 Axis VMC for the selection of YZ plane ______ code is used

a) G19
b) G17
c) G18
d) None
138) ________ preparatory function is used for tool length compensation positive
direction
a)G42
b)G43
c)G44
d)None

139) ______ Preparatory function is related to Work Zero

a) G54
b) G55
c) G56
d) All the Above

140) Work Zero is not in built in the controller and it can be changed

a) True
b) False
c) Neither true nor False
d)None

141) In part programming the symbol “;” explains __________

a) program End
b) End of block
c) Optional end
d) Request end

142) G91 G28 X0 Y0 Z0 in this the preparatory function G28 describes

a)Return to work zero
b) Return to previous point
c) Return to Machine Zero
d) Input in mm

143) G90 G00 G55 X40 Y 30 S4000 M03 in this part programming block G55 Explains
about

a) Machine Datum
b) Work datum
c) Tool shank datum
d) None

144) Secondary Motion parallel to X axis dimension can be designated as _____ letter.

a) V
b) U
c) W
d) None

145) Secondary motion dimension parallel to Y Axis can be designated as ______

letter.

a) V
b) U
c) w
d) None

146) Secondary motion dimension parallel to Z Axis can be designated as _______

letter.

a) U
b) V
c) W
d) None

147) In part programming the letter “O” explains

a) Reference
b) Rewind
c) Reference rewind and Stop
d) None

148) Work zero of the CNC job is called Floating Datum

a) True
b) False
c) Neither True nor False
d) None

149) The detailed plan of manufacturing and Machining instructions is called

_________

a)Modular Tooling
b)Part Programme
c)Support Systems
d) None

150) ______ Miscellaneous function is used for coolant off

a)M08
b)M06
c)M09
d)M10

151) _______ Miscellaneous function is used for coolant on

a)M08
b)M09
c)M12
d)M04

152) The preparatory function for Feed per Minute is _____

a)G90
b)G91
c)G94
d)G96

153) The preparatory function for Feed per Revolution is_____

a)G95
b)G76
c)M95
d)G97

154) In the CNC program “A” letter used _______

a)To specify angle

b)To specify tool function
c)To specify cutter direction
d)None of the above

155) In the CNC program letter “ R” is used to specify ______

a. Radius of arc,
b. Retraction amount.
c. Both a & b
d. None of the above

156) G00 X 70 Z-10 In this block, which is called as DATA.

a. 00 70 -10
b. G X Z
c. G00 X 70 Z-10
d None of the above

157) In the ________ system co-ordinates of any points are calculated with reference
to previous point.
a) Absolute co-ordinate system
b)Incremental co-ordinate system
c)User co-ordinate system
d)None of the abov

158) Preparatory function used for tool length compensation “-“ direction

a. G41
b. G42
c. G43
d. G44

159. G 31 Code stands for _______.

a. Skip Function
b. Thread cutting
c. Automatic tool length measurement
d. Tool offset – increase

160. Which of the following preparatory code is used for cutter radius compensation
cancel .
 a. G 41
b. G 42
c. G 40
d. None
161. G 83 Cycle is used for________.

a. Tapping
b. Boring
c. Drilling
d. Peck Drilling
162. G 18 Code is for ________.

a. XY Plane Selection
b. YZ Plane Selection
c. ZX Plane Selection
d. XYZ Plane Selection

163. G 19 Command is for _________.

a. XY Plane Selection
b. YZ Plane Selection
c. ZX Plane Selection
d. XYZ Plane Selection

164. G 17 Command is for ______.

a. XY Plane Selection
b. YZ Plane Selection
c. ZX Plane Selection
d. XYZ Plane Selection

165. G04 command is used for ________

a. Exact stop, Dwell

b. Spindle Stop
c. Spindle ON
d. None

166. X Axis distance from the start point to the centre of an arc is given as ____.
a. R
b. I
c. J
d. K

167. Y Axis distance from the start point to the centre of an arc is given as ______.

a. R
b. I
c. J
d. K

168. Z Axis distance from the start point to the centre of an arc is given as _____.

a. R
b. I
c. J
d. K

169. The preparatory code G 30 is used to mention ______.

a. Skip Function
b. Thread cutting
c. Tool offset Increase
 d. 2 nd , 3 rd , 4 th reference position return

170. How many types of work piece Co ordinate system ________

a. 2
b. 3
c. 4
d. 6

171. D and H terms are used as parameters of __________

a. Canned Cycle
b. Dwell Time
c. Offset numbers
d. None

172. P and X terms are used as parameters of ________.

a. Canned Cycle
b. Dwell Time
c. Offset numbers
d. None

173. P and Q terms are used as parameters of _________

a. Canned Cycle
b. Dwell Time
c. Offset numbers
d. none

174. Give the value of End Point in Incremental Mode.

a. X 40 Y 70
b. X 60 Y -40
c. X 60 Y 40
d. X-60 Y40.0
175. Give the value of End Point in Absolute Mode

a. X- 40.0 Y 70.0
b. X- 60.0 Y-40.0
c. X 40.0 Y 70.0
d. X 60.0 Y 40.0

176. Rotary axis rotation along X axis is specified by _______.

a. D
b. C
c. B
 d. A
177. Rotary axis rotation along Y axis is specified by _______.

a. D
b. C
c. B
d. A

178. Rotary axis rotation along Z axis is specified by _______.

a. D
b. C
c. B
d. A

179. Parallel axis to X axis is denoted by _________.

a. U
b. V
c. W
d. X

180. Parallel axis to Y axis is denoted by _________.

a. U
b. V
c. W
d. X

181. Parallel axis to Z axis is denoted by _________.

a. U
b. V
c. W
d. X
182. Preparatory code is used to travel from Point 1 to 2

a. GO1
b. G02
c. G03
d. None

183. What Preparatory code is used to travel from Point 1 to 2?

a. GO1
b. G02
 c. G03
d. None

184. In Peck drilling cycle, the term Q denotes _______.

a. Safe Height / R point

b. Number of repeats
c. Final depth
d. Depth of cut for each cutting feed.

185. In G 82 cycle, the term P denotes _________.

a. Number of repeats
b. Dwell time at the bottom of a hole
c. Safe height / R point
d. Final depth

186. For drilling operation, which of the following cutter radius compensation is used
____

a. G 41
b. G 42
c. Either G 41 or G 42
d. None

187. For this profile, _________ cutter radius compensation is used

a. G 41
b. G42
c. Either G 41 or G 42
d. none

188. For this profile, _________ cutter radius compensation is used

a. G 41
b. G42
c. Either G 41 or G 42
d. none

189. For this profile, which of the following block is suitable?

 a. G02 R 250
b. G02 R -250
c. G03 R 250
d. G03 R -250

190. The command G 44 is used for _________

a. CRC Left
b. CRC Right
c. Tool length Compensation +ve Direction
d. Tool Length Compensation -ve Direction

191. For this profile, __________ cutter radius compensation is used.

a. G 41
b. G 42
c. Either A or B
d. none

192. For this profile __________ cutter radius compensation is used.

a. G 41
b. G 42
c. E ither A or B
d. N one

193. In this block G00 X 100.0 Y 20.0, G represents ________.

a. Block
b. Word
c. Address
d. Data

194. In this block G00 X 100.0, 100 represent ________.

 a. Block
b. Word
c. Address
d. Data

195. In this block G00 X 100.0 Y 20.0, G00 represents ________.

a. Block
b. Word
c. Address
d. Data

196. Specify the Co ordinate value of Point 11 in Absolute mode __________.

a. X -35.0 Y 25.0
b. X 35.0 Y -10.0
c. X -35.0 Y 10.0
d. X-35.0 Y-25.0

197. Specify the Co ordinate value of Point 11 in Incremental mode __________.

a. X 20.0 Y 0.0
b. X 0.0 Y 20.0
c. X 0.0 Y-20.0
d. X 20.0 Y-20.0

198. For tapping operation, how do

you calculate the feed rate?

a. Feed = Number of teeth x

feed per tooth x spindle speed
b. R.p.m of spindle x pitch
c. Z x S x n x pitch
d. None.

199. Which code is used in canned cycle, to return to Initial point _______.

a. G 98
b. G 99
c. M 98
d. M 99
200. Which code is used in canned cycle, to return to R point __________.

a. G 98
b. G 99
 c. M 98
d. M 99

201. G 85 canned cycle is for ______.

a. Peck Drilling
b. Tapping
c. Reaming
d. None

202. G 84 canned cycle is for ______.

a. Peck Drilling
b. Tapping
c. Reaming
d. None

203. When we use sub programming technique for repetitive cuts , depth of cut is
given in ______ Co ordinate system

a. Absolute
b. Incremental
c. Both A & B
d. None

204. Program number is usually consist _______ no of digits.

a. 4
b. 3
c. 2
d. 1

205. If the dimension are distributed from one reference point, the command used is
_____.

a. G 90
b. G 91
c. M 90
d. M 91

~end~
206. is motion is either along the spindle axis or parallel to the spindle axis is
.

a. X
b. Y
c. Z
d. none
207. n this Block M06 T 15, 15 stands for _______.

a. 15 mm to be moved in Z axis
b. 15 mm to be moved in X axis
c. 15 mm to be moved in Y axis
d. Tool number 15 to be brought in to spindle replacing the already present tool
in the spindle.

208. Fill the suitable code in the blank , G 99 G 81 _______ Z -10.0 F250 mm/min

a. R 3.0
b. P 3.0
c. U 3.0
d. W 3.0