Tsurumi BER 400V

50Hz

Submersible Ejectors

This submersible ejector is composed of a B type pump and a venturi

with diffusor trumpet.
The large flow from the pump, first, at high speed, draws and
mixes itself with air in the venturi, then in the diffusor changes into
a massive unidirectional horizontal stream of tiny bubbles with
water or sludge.
The pump is of the non-clog single blade shaver type.
 SUBMERSIBLE EJECTOR series BER/TOS-BER

air inlet pipe

air

stirring convection
by bubbles impeller
diffuser

stirring convection
by water current water
micro bubbles are made
by mixing with the jet
water current from the nozzle
nozzle and the lnhaled air

The Tsurumi Submersible Ejector, as shown in the figure, draws air in from around the
jet nozzle (venturi) by means of the water power discharged from the submersible
pump.
A mixture of air and water is produced in the venturi and trumpet shaped diffuser and
discharged at high speed.
This results in a unidirectional stream of this mixture together with much entrained
water.
In time, the stream makes itself felt directly and indirectly over a large area and depth,
helped in this churning effect by the draw of water underneath the pump.
Furthermore, even if the water depth fluctuates, the required shaft power hardly
changes. The volume of air emission is freely adjustable as well. Because of this, the
submersible ejector is also ideal as an aerator in equalizing tanks where the fluctuation
in the water level is comparatively great.
This unit can be used with confidence as the main aerator in industrial waste water
treatment systems.
A particularly large sales point is the fact that due to the air/water collision that occurs
while the suction-inducted air is in a minutely particulated state, oxygen dissolution
efficiency is remarkably high.

2
 THE PRINCIPLE OF THE EJECTOR SYSTEM
This system is a combination of a submersible pump and a jet pump.
By the action of the ejection current of the submersible pump, a self-feeding force is
generated, which draws air from the surface of the water through an air inlet pipe.
This air is mixed with the water and the mixture is ejected.
The churning force caused by this ejection current is remarkably strong, with the result
that exceptionally efficient oxygen dissolution is produced.

Air is drawn in by the

force of the water jet
Submersible
pump

CONVECTION PATTERN AND RECOMMENDED INSTALLATION

Circular Tank

Square Tank Rectangular Tank

bubble
current

water
current

3
 BER consists of:
• B-series Pump
• Ejector including
Silencer & Valve Set and
Lifting Chain

TOS-BER consists of:

• B-series Pump
• TOS-Ejector including
Silencer & Valve Set and
Lifting Chain

Specifications:

model output phase r.p.m. starting air inlet

kW method diameter
free standing guide rail fitting mm
8-BER4 TOS-8BER4 0,75 Three 3000 d.o.l. 25
15-BER3 TOS-15BER3 1,5 Three 3000 d.o.l. 32
22-BER5 TOS-22BER5 2,2 Three 1500 d.o.l. 50
37-BER5 TOS-37BER5 3,7 Three 1500 d.o.l. 50
55-BER5 TOS-55BER5 5,5 Three 1500 d.o.l. 50

Convection Pattern:

Bubble
Water Current
Current

The BER ejector can be placed on a solid flat surface, be it the bottom of a pit or lake
or river, or a fabricated structure supported from the water´s edge or a pontoon.

The TOS-BER fits together differently. The TOS-BER´s venturi (with the diffusor
trumpet fixed to it) has a foot for fixing to masonry by means of bolts, and a pair of
spigots for slide tubes; the pump has a flange with claws for sliding up an down slide
tubes. A clamp for the top of a pair of slide tubes is also supplied. When installed as
intended, the pump can be lifted out for inspection whilst the venturi and diffusor remain
fixed to the bottom or supporting structure, ensuring exact return to the original position
when the pump is lowered in place.
4
Air Emission volume-Water Depth Curve
(at 20°C, air emission value may vary ±5%)

Air Emission Volume (Nm3/h)

Water Depth (mAq)

model tank dimension dry weight kg max. cable

max. max. max. Free TOS- solids length
length width depth standing model handling m
free standing guide rail fitting m m m mm
8-BER4 TOS-8BER4 3,0 2,0 4,0 28 23 20 10
15-BER3 TOS-15BER3 4,0 3,5 4,0 43 34 20 10
22-BER5 TOS-22BER5 5,0 5,0 4,5 75 61 35 10
37-BER5 TOS-37BER5 6,0 6,0 5,0 91 77 35 10
55-BER5 TOS-55BER5 7,0 7,0 6,0 149 132 35 10

5
DIMENSIONS Unit:mm

Silencer & Valve Set

Air pipe Bore A øB C

ø25 147 91 210
ø32 180 116 275
ø50 230 154 370

6
 DIMENSIONS Unit: mm

values in ( ) for TOS-37BER3

7
 DESIGN AND MATERIALS

No. DESCRIPTIONS MATERIAL No. DESCRIPTIONS MATERIAL No. DESCRIPTIONS MATERIAL No. DESCRIPTIONS MATERIAL
1 Cabtyre Cable Rubber 54 Shaft EN-X6Cr13/X30Cr13 1 Cabtyre Cable Rubber 55 Rotor
20 Pump Casing Grey Iron Casting 55 Rotor 20 Pump Casing Grey Iron Casting 56 Stator Complete
21 Impeller Grey Iron Casting 56 Stator Complete 21 Impeller Grey Iron Casting 64 Motor Frame Grey Iron Casting
22 Suction Cover Grey Iron Casting 64 Motor Frame Grey Iron Casting 22 Suction Cover Grey Iron Casting 72 Lifting Eye Bolt EN-X5CrNi18-10
25 Mechanical Seal Silicon Carbide 72 Lifting Eye Bolt Structure Steel 25 Mechanical Seal Silicon Carbide 93 Guide Hook Ductile Iron Casting
26 Oil Seal Nitrile Rubber 95 Lifting Chain Structure Steel 26 Oil Seal Nitrile Rubber 94 Guide Support Ductile Iron Casting
48 Screw Flange Grey Iron Casting 151 Air-Inlet Casing Grey Iron Casting 52 Bearing Ball Bearing 95 Lifting Chain Structure Steel
52 Bearing Ball Bearing 152 Nozzle Structure Steel Nylon Coated 53 Motor Protector 151 Air-Inlet Casing Grey Iron Casting
53 Motor Protector 153 Diffuser Structure Steel Nylon Coated 54 Shaft Stainl.steel EN-X6Cr13 152 Nozzle Structure Steel Nylon Coated
153 Diffuser Structure Steel Nylon Coated

No. DESCRIPTIONS MATERIAL No. DESCRIPTIONS MATERIAL No. DESCRIPTIONS MATERIAL No. DESCRIPTIONS MATERIAL
1 Cabtyre Cable Rubber 53 Motor Protector 1 Cabtyre Cable Rubber 55 Rotor
3 Cable Gland Grey Iron Casting 54 Shaft Stainl.steel EN-X6Cr13 3 Cable Gland Grey Iron Casting 56 Stator Complete
20 Pump Casing Grey Iron Casting 55 Rotor 20 Pump Casing Grey Iron Casting 64 Motor Frame Grey Iron Casting
21 Impeller Grey Iron Casting 56 Stator Complete 21 Impeller Grey Iron Casting 72 Lifting Eye Bolt EN-X5CrNi18-10
22 Suction Cover Grey Iron Casting 64 Motor Frame Grey Iron Casting 22 Suction Cover Grey Iron Casting 93 Guide Hook Ductile Iron Casting
25 Mechanical Seal Silicon Carbide 72 Lifting Eye Bolt EN-X5CrNi18-10 25 Mechanical Seal Silicon Carbide 94 Guide Support Ductile Iron Casting
26 Oil Seal Nitrile Rubber 95 Lifting Chain Structure Steel 26 Oil Seal Nitrile Rubber 95 Lifting Chain Structure Steel
48 Screw Flange Grey Iron Casting 151 Air-Inlet Casing Grey Iron Casting 52 Bearing Ball Bearing 151 Air-Inlet Casing Grey Iron Casting
52 Bearing Ball Bearing 152 Nozzle Structure Steel Nylon Coated 53 Motor Protector 152 Nozzle Structure Steel Nylon Coated
153 Diffuser Structure Steel Nylon Coated 54 Shaft Stainl.steel EN-X6Cr13 153 Diffuser Structure Steel Nylon Coated

We reserve the right to change specifications and designs herein for improvement without prior notice. Our pumps are for professional use only. In the event that
Tsurumi (Europe) GmbH have, in exceptional cases taken over, a manufacturer’s warranty, this entitles the end-user to assert remedy free of charge against Tsurumi
(Europe) GmbH due to any defect to the product occurring during the guarantee period (see below), also then when the warranty claims against the seller do not or
no longer exist. In the event of malfunction, which is attributable to the improper handling by the enduser, no guarantee claim shall arise. Further claims shall not
result from the warranty, unless if something to the contrary has explicitly been determined. The decision as to whether remedy is effected by way of replacement
or repair shall be at the choice of Tsurumi (Europe) GmbH. The claims shall be time barred after a period of three months after expiry of the guarantee period,
however, not before expiry of the warranty period which is valid towards the seller. In the event of doubt, the warranty period shall correspond with the warranty
period which is valid between the end-user and his seller.

Tsurumi (Europe) GmbH Your Dealer

Cat.-no. BER-E-06/08

Heltorfer Straße 14
D-40472 Düsseldorf
Tel.: +49-211-4179373
Fax: +49-211-4791429
Email: sales@tsurumi-europe.com
www.tsurumi-europe.com