N-DIN Line Protection Relays

N-DIN-TO64
D.C. CURRENT RELAY with HIGH SENSITIVITY
HALL EFFECT TRANSDUCER

The relay N-DIN-TO64 connected to the magnetic detector

TO64 allows for very accurate measurement of DC current on a
rated current od over 1000A. The operation of the relay can be
unidirectional or bidirectional. The rated insulation voltage of
the magnetic detector TO64 is over 5kV (dielectric test voltage
10kV-50Hz 1 min or 15kV on request).

The N-DIN relay is surface mounted on standard DIN-EN 50022

rail, but its Front-Face Panel (FFP) including Controls, Signals
and Display, is removable and can be flush mounted, apart
from the Relay Main Body (RMB), on the front panel of the
switch board or of the MCC drawers. When removed, the FFP
is connected to the RMB via a dedicated serial link by a normal
wire and screw terminals. One FFP only can control and
supervise up to 31 RMB units. Another RS232 port is available
on the FFP front for local connection to a PC.

Similarly the RMB, besides the Serial Port connecting the FFP, has
another RS485 serial port, with screw terminals, for connection
to the serial bus of the DCS. The relay main body RMB can be
used as a stand-alone unit, without the front panel FFP.

Protective Functions Communications

• F64 : Two Earth fault protection element. FFP
• F51BF : Breaker Failure protection. • 1 RS232 serial port (front)
• 1 RS485 serial port (rear)
Measurements
• Measurement of input earth current (Primary Ampere). RMB
• 1 RS485 port for connection to the communication serial bus.
Control • 1 RS485 port for communication to the Front Face Panel.
• 2 Programmable output relay (R1, R2). (FFP Option).
• Load Profile.
G28-ING-Rev.06

• Operation counters. • Communication protocol is MODBUS-RTU for all the Ports.

• Event recording.
• 3 Digital Inputs. Power supply Ratings
(Reset, Remote trip / C/B status, Blocking input) Type 1 : 24V(-20%) / 80V(+15%) a.c. - 24V(-20%) / 90V(+20%) d.c.
Type 2 : 80V(-20%) / 230V(+15%) a.c. - 90V(-20%) / 250V(+20%) d.c.
Technical Characteristics Mounting
FFP RMB • DIN46227 (EN50022)
• Display 2x16 characters. • 2 signal led.
• 4 signal leds. • 1 Reset button. Software
• 4 push-button. • MSCom program interface for device management.
2

Protection Relays N-DIN-TO64

F64 (I>): First overcurrent element

Function enabling : Enable/Disable
Setting range : I> = (4 ¸ 100)%In step 1%In
Instantaneous output : £0.03s
Independent time dalay : tI> = (0.03 ¸ 60) step 0.01s
Trip detection : Bidirectional / Positive / Negative
F64 (I>>): Second overcurrent element
Function enabling : Enable/Disable
Setting range : I> = (4 ¸ 100)%In step 1%In
Instantaneous output : £0.03s
Independent time dalay : tI> = (0.03 ¸ 60) step 0.01s
Trip detection : Bidirectional / Positive / Negative
Breaker Failure Element
Trip time delay : tBF = (0.05 ÷ 0.75)s step 0.01s

RS232
1.. ..2.. ..31 DCS

RS485

RMB+FFP
1 for each unit

1.. ..2.. ..31 DCS

RS485

UP TO 31 RMB
2 managed by only one FFP
G28-ING-Rev.06

RS232/485
RS485
1.. ..2.. ..31 DCS

RS485

RMB Modules
3 without FFP
ANY COMBINATION 1 - 2 - 3 IS POSSIBLE
 3

Protection Relays N-DIN-TO64

TRASPARENT COVER - Dimensions = 45x108 - Height = 9

REMOVABLE FFP - Height = 16 RMB - Height = 72

FRONT FACE
(FFP)
DIN46277
50
(EN50022)
PANEL O3
35 CUT-OUT

90 45
106
96

85

106

(mm)

156
150
110
10

K In
3 4
In = 100A

G28-ING-Rev.06
K= xxxx
60
30

145

P1
TO64

1 2

P1

N. 4 HOLE
R7.00

(mm)
4

Protection Relays N-DIN-TO64

Connection Diagram
FFP
Display / Keyboard / Signals
A B + 0
RS485

RS485 RMB
P1
A B + 0
(*)
2 15
N-DIN-TO64 R1 19

3 14 FUNCTIONS
+
1 13 20
F64
4 12
R2 16

(*) ATTENZIONE! NON COLLEGARE LO SCHERMO A TERRA

ATTENCTION! DON'T CONNECT THE SCREEN TO GROUND 17

H
1 TO
L EX-I/O
2
8 D1
Reset Riarmo C
9 D2
3
Blocking Input Ingresso di blocco
7
PWR/I.R.F
D3 B (S-)
Remote Scatto Trip 4
ON A (S+) RS485
6 5
Common Comune
OFF
21
_
Auxiliary Supply
Alimentazione Ausiliaria
= =
22

MS-SCE2038-R1

Typical characteristics - N-DIN

Accuracy at reference value of influencing factors 5% for measurement with max 1% of FS
2% ±10ms for times
Input from magnetic detector TO64
Averange power supply consumption <10VA
Output current rating 6 A; Vn = 250 V
resstive swictching = 1500W (400V max)
make= 30 A (peak) 0.5 sec. break = 0.2 A, 110 Vcc,
L/R = 40 ms (100.000 op.)
In option to relay R1 Relè in opzione al relè R1 4 ¸ 20mA (0 ¸ 12)mA
Typical characteristics - Magnetic Detector
Frequency response 0 ¸ 100 kHz
Maximum distance "Relay/magnetic detector" <10 meters (shielded cable)

Type In (A) (*) Ith (A) Vn (Vcc) Measurement Dielectric Maximum Dinamic
Max. admisible Range withstand Current
Rated Input continuous Rated Input (A) Voltage (kA per 1s)
Current overlod Voltage 1’@50Hz (kV)

TO64 - 100 100 1000 1000 4 ¸ 100 10 100

TO64 - 500 500 1000 1000 20 ¸ 500 10 100
G28-ING-Rev.06

TO64 - 100H 100 1000 5000 4 ¸ 100 18.5 100

TO64 - 500H 500 1000 5000 20 ¸ 500 18.5 100

(*) on request other value

Order Code - Example :

N-DIN-TO64 1 1
Power Supply Options
1 = Type 1 1 = Standard (RMB+FFP)
2 = Type 2 2 = Only RMB
3 = Only FFP

The performances and the characteristics reported in this document are not binding and can modified at any moment without notice

Microelettrica Scientifica S.p.A. - 20090 Buccinasco (MI) - Via Lucania 2, Italy

Tel. +39 02 575731 - Fax +39 02 57510940 - E-Mail: sales.relays@microelettrica.com
www.microelettrica.com