Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 321 views

    Transfer Case: Component Tests and General Diagnostics AWD Solenoid

    Uploaded by

    julio montenegro
    nissan

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Transfer Case: Component Tests and General Diagnostics AWD Solenoid

    Uploaded by

    julio montenegro
    321 views3 pages
    nissan

    Original Title

    diagn diferential lock murano

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    nissan

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    321 views3 pages

    Transfer Case: Component Tests and General Diagnostics AWD Solenoid

    Uploaded by

    julio montenegro
    nissan

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 3
    At a glance
    Powered by AI
    The document outlines diagnostic procedures for checking components of an all-wheel drive (AWD) system, including checking the AWD solenoid, power supply, and circuits.

    The procedure involves using a diagnostic tool to check the AWD solenoid signal while the engine is running, then checking the power supply and various circuits if the signal is not OK.

    The steps include turning off the ignition, disconnecting the AWD control unit connector, and checking the resistance between terminals 1 and 2.

    2005 Nissan-Datsun Truck Murano AWD V6-3.5L (VQ35) Copyright © 2013, ALLDATA 10.

    52SS Page 1

    Transfer Case: Component Tests and General Diagnostics


    AWD Solenoid
    AWD Solenoid

    CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE

    DIAGNOSTIC PROCEDURE
    ^ Check the following if "4WD SOLENOID [C1204]" is displayed in self-diagnostic results of CONSULT-II.

    1. CHECK AWD SOLENOID SIGNAL

    With CONSULT-II
    1. Start engine.
    3. Select "DATA MONITOR" mode for "ALL MODE AWD/4WD" with CONSULT-II.

    3. Read out the value of "ETS SOLENOID".


    OK or NG
    OK >> GO TO 6.
    NG >> GO TO 2.

    2. CHECK POWER SUPPLY


    1. Turn ignition switch "OFF".
    2. Disconnect AWD control unit harness connector.
    3. Turn ignition switch "ON". (Do not start engine.)
    2005 Nissan-Datsun Truck Murano AWD V6-3.5L (VQ35) Copyright © 2013, ALLDATA 10.52SS Page 2

    4. Check voltage between AWD control unit harness connector terminal 9 and ground.
    OK or NG
    OK >> GO TO 3.
    NG >> Check the following. If any items are damaged, repair or replace damaged parts.
    ^ 10A fuse [No. 37, located in the fuse and fusible link block]
    ^ Harness for short or open between battery and AWD control unit harness connector terminal 9

    3. CHECK AWD SOLENOID CIRCUIT


    1. Turn ignition switch "OFF".
    2. Disconnect AWD control unit harness connector.

    3. Check resistance between AWD control unit harness connector terminals 1 and 2.
    OK or NG
    OK >> GO TO 6.
    NG >> GO TO 4.

    4. CHECK AWD SOLENOID


    1. Turn ignition switch "OFF".
    2. Disconnect AWD solenoid valve harness connector.

    3. Check resistance between AWD solenoid valve harness connector B204 terminals 1 and 2.
    1 - 2: Approximately 2.45 Ohms
    OK or NG
    OK >> GO TO 5.
    NG >> AWD solenoid is malfunctioning. Replace electric controlled coupling. Refer to "Disassembly and Assembly".

    5. CHECK HARNESS BETWEEN AWD CONTROL UNIT AND AWD SOLENOID


    1. Turn ignition switch "OFF".
    2. Disconnect AWD control until harness connector and AWD solenoid valve harness connector.
    2005 Nissan-Datsun Truck Murano AWD V6-3.5L (VQ35) Copyright © 2013, ALLDATA 10.52SS Page 3

    3. Check continuity between the following terminals.


    - AWD control unit harness connector E111 terminal 1 (LG) and AWD solenoid valve harness connector B204 terminal 1 (LG).
    - AWD control unit harness connector E111 terminal 2 (L/W) and AWD solenoid valve harness connector B204 terminal 2 (L/W).
    1 (LG) -1 (LG): Continuity should exist.
    2 (L/W) - 2 (L/W): Continuity should exist.
    Also check harness for short to around and short to power.
    OK or NG
    OK >> GO TO 6.
    NG >> Repair or replace damaged parts.

    6. CHECK AWD CONTROL UNIT


    Check AWD control unit input/output signal. Refer to "AWD Control Unit Input/Output Signal Reference Values".
    OK or NG
    OK >> GO TO 7.
    NG >> Check AWD control unit pin terminals for damage or loose connection with harness connector. If any item is damaged, repair or
    replace damaged parts.

    7. CHECK DTC
    Perform the self-diagnosis, after driving a vehicle for a while.
    OK or NG
    OK >> INSPECTION END
    NG >> Replace AWD control unit.

    COMPONENT INSPECTION
    1. Turn ignition switch "OFF".
    2. Disconnect AWD solenoid valve harness connector.

    3. Check resistance between AWD solenoid valve harness connector B204 terminals 1 and 2.
    1 - 2: Approximately 2.45 Ohms
    4. If NG, replace electric controlled coupling. Refer to "Disassembly and Assembly".

    You might also like