94020

Conservation Vent (Pressure & Vacuum)

94020 Conservation Vent (Pressure & Vacuum)

The Shand & Jurs Model 94020 Conservation Vent
is designed utilizing over 90 years of experience in
producing high quality and dependable conservation
fittings. Continued design improvements provide these
vents with high efficiency, maximum flow capacity and
minimum leakage. The easily serviceable configuration
and lightweight construction reduces maintenance
and installation costs.
Standard materials of construction are low copper
aluminum, cast iron, ductile iron, cast steel and 316
stainless steel for body materials. Aluminum, stainless Open Vent
steel and steel body vents come standard with integral
seats and have optional replaceable seats. Cast iron
and ductile iron bodies come with replaceable seats
as standard design. Replaceable seats are made of
corrosion resistant molded thermosetting phenolic,
Teflon, aluminum, 316 stainless steel or stainless steel
Teflon coated and are easily replaced.
Diaphragms are air cushion seated and are constructed Closed Vent
of FEP Teflon for reliability and extended service life.
Teflon diaphragms contribute to high resistance to Features
adhesion of ice and gum formations, thus assuring
protection against pallet sticking to the seating • Suitable materials available for
surface. The body is self-draining and drip rings keep corrosive/extreme temperature
condensates from the seating surfaces. The carefully
engineered body, seat, and pallet assembly results service pallet reaction lip for smooth
in a superior combination of tight sealing and high lift and reseating
capacity at low over-pressure with minimal blow
down.
• Pallet reaction lip for smooth lift and
Conservation Vents are available in a full range of sizes
and configurations, such as closed vent hoods (pipe- reseating
away), cryogenic hoods and flame snuffers. Standard
pressure and vacuum settings are 0.5 oz/in2. The 94020
Conservation Vent is available with optional pressure • Vertical lift pallets assure reliable
and vacuum limit switches and visual indicators.
operation and maximum flow
Expanda-Seal
Shand & Jurs “Expanda-Seal” option is available on • Floating diaphragm results in a
all pressure pallet assemblies. This feature significantly positive seal and minimal blow-down
reduces leakage. The ballooning effect of the Teflon
diaphragm effectively seals the valve. • “All weather” coating, insulation
The “Expanda-Seal” feature ensures less than 0.5 SCFH jackets and steam jacketing options
of air at 95% of the set point. available
Pressure Below Set Point Approaching Set Point Set Point Exceeded
• Capacity certified to API Standards

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

1
 94020
Conservation Vent (Pressure & Vacuum)

Conservation Vent Specifications:

Sizes: Temperature Range:
2’’, 3’’, 4’’, 6’’, 8’’, 10” & 12” Body and Seal -40oF to 220oF. Options for Process
Temperature Ranges of -300oF to 500oF
Settings*:
Standard Pressure & Vacuum: 0.5 oz/in2 Replaceable Seats:
(.865 in. W.C.) Ryton for: 2” size
Aluminum for: 2”, 3”, 4”, 6”, 8”, 10” & 12” sizes
Expanda-Seal Pressure Setting: 316 Stainless Steel for: 2”, 3”, 4”, 6”, 8”, 10” & 12” sizes
1.5 oz/in2 Minimum (Consult Factory for lower settings) Teflon for: 2”, 3”, 4”, 6”, 8” sizes
SS Teflon Coated for: 2”, 3”, 4”, 6”, 8”, 10” & 12” sizes
Maximum Setting W/O Modification:
(Pressure) (Vacuum)** Type of Flange Connection:
2”: 12 oz/in2 8 oz/in2 Screwed or flanged for: 2” & 3” sizes
3”: 12 oz/in2 9 oz/in2 Flanged for: 4”, 6”, 8”, 10” & 12”sizes
4”: 12 oz/in2 11 oz/in2 Raised face flange available, except for aluminum
6”: 10 oz/in2 10 oz/in2 body material.
8”: 8 oz/in2 8 oz/in2
10”: 6 oz/in2 6 oz/in2 Options Available:
12”: 5 oz/in2 5 oz/in2 Flame Snuffer for all sizes (open vent) and material,
except low temperature service. Closed vent for all
Service and Body Material: sizes and materials. Material substitutions as required.
Normal: Cast Low Copper Aluminum Cleaning for LOX/LIN service.
Low Temperature: Cast Low Copper Aluminum
NOTES:
Severe: Cast Iron, Ductile Iron, Cast Steel, Cast 316 ** Modifications may be required to vacuum port for installations where
Stainless Steel product contamination may occur. See figure 4 for Principle of Operation.
Caution— any obstruction to vacuum port may alter the set point.
Integral Seats: Same as body; Aluminum, 316 SS,
Cast Steel with 316 Stainless Steel seat overlay

Standard Materials of Construction

Component Normal Aluminum Low Temperature* Severe
Body Cast Aluminum Cast Aluminum Cast Iron/Ductile Iron Cast Steel 316 Stainless Steel
Cover Aluminum Aluminum Steel Steel 316 Stainless Steel
Hood 18-8 Stainless Steel, PA1 Aluminum2 18-8 Stainless Steel, PA1 18-8 Stainless Steel, PA1 316 Stainless Steel
Seats3 Aluminum Aluminum 316 Stainless Steel C.S. with 316 SS Overlay 316 Stainless Steel
Stem Guide Galvanized Iron Galvanized Iron 304 Stainless Steel 304 Stainless Steel 316 Stainless Steel
Pallets Aluminum Aluminum 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
Distribution Plate 4,5 Aluminum Aluminum Steel Steel 316 Stainless Steel
Pressure Stem 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
Vacuum Stem Aluminum6 Aluminum6 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
Screens Galvanized Steel Galvanized Steel 304 Stainless Steel 304 Stainless Steel 316 Stainless Steel
Retainer Aluminum Aluminum 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel
Hardware Zinc Plated Steel Zinc Plated Steel 316 Stainless Steel Zinc Plated Steel 316 Stainless Steel
Diaphragms FEP Teflon FEP Teflon FEP Teflon FEP Teflon FEP Teflon
PA - Spun Aluminum CS - Cast Steel
NOTES: 1. 18-8SS for 2”, 3”, 4”, 6” & 8” sizes; spun alum. for 10” & 12” sizes. 4. When Provided
2. 2”, 3”, 4”, 6”, 8”, 10” & 12” sizes ; alum. enclosure w/flapper. 5. SS weights option includes SS distribution plate
3. Material same as body except CI and DI. 6. 316SS for elevated settings.
*NOTE: For Cryogenic Service, must add Stainless Steel Trim on Table H, Option 5, 6 or 7

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

2
94020
Conservation Vent (Pressure & Vacuum)

Principle of Operation

Figures 1 and 3 show the relation of the pressure or

vacuum pallet assembly to the seat when atmospheric
and tank pressures are equal. The “wrap around” effect
of the resilient diaphragm on the edge of the seat and
the resulting high ratio of seating force to seating area
affords a tight seal.

As the pressure or vacuum increases, the pallet begins

to rise. Because there is still a wrap-around effect on
the edge of the seat, good sealing is maintained. Teflon
diaphragm memory and lapped seating surface further
enhance sealing characteristics.

As increasing pressure or vacuum continues to lift

the pallet, the diaphragm is held in close proximity to
the seat by the flat plane memory of the diaphragm
material.

As set pressure or vacuum is reached the diaphragm

leaves the seat (see Figures 2 and 4) and the escaping
vapor lifts the pallet even further.

The vacuum pallet is guided in the same manner as the

pressure pallet. Both are pallet stem and pallet side
guided for smooth movement.

Steam Jacket Option:

Designed for use on tanks containing liquids whose

vapors crystallize at ambient temperatures. Stainless
steel pressure and vacuum pallets are cased in a steam
heated jacket ensuring the valves will be free from
plugging. The jacket is steel or stainless steel construction.
The standard jacket can withstand steam pressures up
to 100 psig. Higher pressure ratings are available.

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

3
 94020
Conservation Vent (Pressure & Vacuum)

6”, 8”, 10” & 12” Cryogenic Hood Model

Notes:

1) CONNECTION SIZE MATCHES

125 #FF ANSI, EN1092-1 FLANGE.
150

2) MOUNTING HOLES STRADDLE

CENTERLINE.

3) DIMENSIONS EXPRESSED IN
INCHES.

Dimensions in Inches
Vent Size* (In.)
“B” “D” “E” “F” “H” “J” “L” “P” “R1” “R2”
6" 11 3/4 27 1/4 18 3/4 8 1/8 5 5/8 11 1/2 8 1/2 11 5/8 R6 1/16 R5 21/32
8" 14 1/2 31 9/32 22 1/8 9 5/8 6 23/32 12 1/2 9 3/4 14 7/8 R7 11/32 R7 1/32
10" 17 1/2 39 3/16 28 1/2 11 3/8 8 1/8 14 3/16 11 3/8 17 R8 3/4 R8 11/32
12" 20 5/8 45 11/16 32 1/4 12 5/8 9 3/4 15 13/32 12 1/2 19 7/16 R9 7/8 R9 21/32

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

4
94020
Conservation Vent (Pressure & Vacuum)

94020 Closed Vent

Valve Outlet
“H” “J” “K” “L” “B”
Size Size
2” 2” 13 11 1/8 5 1/32 4 1/4 8 3/4
2” 3” 13 11 1/8 5 1/32 4 1/4 8 3/4
* 3” 3” 16 3/8 13 1/4 5 9/16 5 1/4 11 1/8
3” 4” 16 3/16 13 3/4 5 31/32 5 1/4 10 15/16
* 4” 4” 20 20 3/8 7 6 1/2 13 1/2
4” 6” 19 1/4 15 3/4 7 1/32 5 15/16 13 5/16
* 6” 6” 26 1/4 21 1/4 9 3/8 8 3/8 17 7/8
6” 8” 26 3/16 21 1/4 10 11/32 8 1/4 17 15/16
* 8” 8” 31 5/8 25 1/2 11 11/16 9 3/4 21 7/8
8” 10” 31 5/8 26 3/16 12 23/32 9 3/4 21 7/8
*10” 10” 37 7/8 30 13 7/8 11 19/32 26 9/32
10” 12” 37 7/8 30 1/4 14 29/32 11 19/32 26 9/32
*12” 12” 43 3/8 33 7/8 16 1/4 12 13/16 30 9/16
12” 14” 43 3/8 33 7/8 16 29/32 12 13/16 30 9/16
NOTES:
*Table D option 5 for same size inlet and outlet connections has
been obsoleted and replaced by Table D option 6. Dimensions 1. Connection size matches ANSI, EN1092-1 & JIS.
do not match. Consult Factory for replacement valve. 2. Mounting Holes straddle centerline except: 2” & 3” sizes;
holes are on centerline.
3. Optional NPT Adapter available for 2” & 3”.
4. Dimensions expressed in inches.
5. Raised faced flanges with smooth finish are standard. For optional

94020 Open Vent

serrated raised faced flanges, consult factory.

Valve Diameter
“B” “D” “E”
Size “F”
2” 9 15 1/4 11 1/8 12 7/8
3” 11 1/8 17 15/16 13 3/4 13 9/16
4” 13 1/2 21 1/2 15 3/4 15 15/16
6” 17 15/16 28 1/2 18 3/4 18 5/8
8” 21 7/8 31 3/16 21 1/4 18 5/8
10” 26 1/4 40 5/8 28 1/8 25 9/16
12” 30 9/16 44 5/8 32 1/4 29 7/8
NOTES:

1. Connection size matches ANSI, EN1092-1 & JIS.

2. Mounting Holes straddle centerline except: 2” & 3” sizes;
holes are on centerline.
3. Optional NPT Adapter available for 2” & 3”.
4. Dimensions expressed in inches.
5. Raised faced flanges with smooth finish are standard. For optional
serrated raised faced flanges, consult factory.

All designs subject to change. Certified dimensions and specifications available upon request

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

5
 94020
Conservation Vent (Pressure & Vacuum)

94020 Ordering Guide

Conservation Vents provide tank venting and breathing with high efficiency, maximum flow capacity and
minimum leakage. Standard materials of construction include low copper aluminum, cast iron, ductile iron,
cast steel, and 316 Stainless Steel. The 94020 comes in open or closed vent versions, and in sizes 2” through
12”. Cryogenic hoods, flame snuffers, limit switches and steam jacketing and steam tracing are available.

Benefits
• Low copper aluminum alloy construction reduces
need for special materials in corrosive and extreme • Unique floating diaphragm construction assures
temperature service positive seal and minimal blowdown, thus
conserving valuable tank content
• Capacity certified in accordance with API
standards • Peripheral and stem guided pressure pallet assures
smooth lift and closure
• Expanda-Seal diaphram for reduced leakage

Model Number Selection

The model number will have a base number 94020 followed by 8 digit numbers. These digits will represent 7
sets of option tables.

94020 - AB - CD - EF - GH

*NOTE: If ATEX (A) Unit is required, please use 94020A AB CD EF GH.

If CE (C) Unit is required, please use 94020C AB CD EF GH.

Ordering Information
Specify:

1. Model 94020 Conservation Vent

2. Size and Body Material
3. Screwed or Flanged Connection on 2” and 3” Size
4. Closed Vent or Vent to Atmosphere
(With or without flame snuffer)
5. Pressure and Vacuum Settings
(if other than normal setting)
6. Type of Cleaning (if for oxygen service)
7. Optional Materials of Construction, as Required
8. To Specify CE for Ordinary EU Locations use
94020C AB CD EF GH
9. To Specify ATEX Certification for Group IIB, IIA EU Locations
use 94020A AB CD EF GH. ATEX Certification includes
CE Mark.

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

6
 94020
Conservation Vent (Pressure & Vacuum)

Table AB - Size and Body Material

Option Type of Option Type of
Size Body Material Size Body Material
AB Connection AB Connection
11 2” NPT Aluminum *35/45 4“ Flanged Cast Iron/Ductile Iron
12 2” Flanged Aluminum 55 4” Flanged Cast Steel
21 2” NPT Alum. Cryo Hood1 75 4” Flanged 316 Stainless Steel
22 2” Flanged Alum. Cryo Hood1 16 6” Flanged Aluminum
*31/41 2” NPT Cast Iron/Ductile Iron 26 6” Flanged Alum. Cryo Hood1
*32/42 2” Flanged Cast Iron/Ductile Iron *36/46 6” Flanged Cast Iron/Ductile Iron
51 2” NPT Cast Steel 56 6” Flanged Cast Steel
52 2” Flanged Cast Steel 76 6” Flanged 316 Stainless Steel
71 2” NPT 316 Stainless Steel 17 8“ Flanged Aluminum
72 2” Flanged 316 Stainless Steel 27 8” Flanged Alum. Cryo Hood1
13 3” NPT Aluminum *37/47 8” Flanged Cast Iron/Ductile Iron
14 3” Flanged Aluminum 57 8” Flanged Cast Steel
23 3” NPT Alum. Cryo Hood1 77 8” Flanged 316 Stainless Steel
24 3” Flanged Alum. Cryo Hood1 18 10” Flanged Aluminum
*33/43 3” NPT Cast Iron/Ductile Iron 28 10” Flanged Alum. Cryo Hood1
*34/44 3” Flanged Cast Iron/Ductile Iron *38/48 10” Flanged Cast Iron/Ductile Iron
53 3” NPT Cast Steel 58 10” Flanged Cast Steel
54 3” Flanged Cast Steel 78 10” Flanged 316 Stainless Steel
73 3” NPT 316 Stainless Steel 19 12” Flanged Aluminum
74 3” Flanged 316 Stainless Steel 29 12” Flanged Alum. Cryo Hood1
15 4” Flanged Aluminum *39/49 12” Flanged Cast Iron/Ductile Iron
25 4” Flanged Alum. Cryo Hood1 59 12” Flanged Cast Steel
* 3X = Cast Iron 4X = Ductile Iron 79 12” Flanged 316 Stainless Steel
**For NPT Connections, Specify Table C0
1. NOTE: For full Cryogenic Service, must add Stainless Steel Trim

Table C - Flange Type Table D - Vent Type

Option C Description Option D Description
0 ANSI 125/150 lb. FF 1 Open Vent
1 ANSI 125/150 lb. RF* 2 Open Vent w/ Flame Snuffer
2 EN1092-1 PN16 FF 3 Closed, Standard Outlet > Inlet*
3 EN1092-1 PN16 RF* 4 Pipe Away, P&V
4 JIS 10K FF 6 Pipe Away, Same Size Inlet and Outlet
5 JIS 10K RF* 7 Open Vent with “All Weather” Coating
* RF not available in Aluminum. Open Vent with Flame Snuffer with
** Raised faced flanges with smooth finish are standard. For optional 8
serrated raised faced flanges, consult factory.
“All Weather” Coating
Closed, Standard Outlet > Inlet with
9
“All Weather” Coating
Pipe Away, Same Size Inlet, Outlet, Seat
A
with “All Weather Coating
* Standard closed vent (outelet is one size larger than the inlet).
Ex. 2” Inlet X 3” Outlet, 6” Inlet X 8” Outlet.
NOTE: Replaced Option 5. Dimensions are not idetntical. Consult Factory if
replacement valve is required.

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified

7
 94020
Conservation Vent (Pressure & Vacuum)

Table E - Pallet / Seal Type Table G - Seat & Pallet Material

Option E Pallet Type Diaphragm Option G Seat Pallet
0 Standard FEP 0 Standard* Standard*
1 Expanda-Seal FEP +1 Teflon Standard*
4 Standard VITON 2 Aluminum Standard*
5 Expanda-Seal VITON 4 Stainless Steel Standard*
8 Standard BUNA-N 5 Teflon Coated SS Standard*
9 Expanda-Seal BUNA-N
A Standard* 316 Stainless Steel
Temperature Limits +B Teflon 316 Stainless Steel
C Aluminum 316 Stainless Steel
Diaphragm Material Temperature Range
E Stainless Steel 316 Stainless Steel
FEP -65 F to 400 F
F Teflon Coated SS 316 Stainless Steel
VITON -15 F to 400 F
*See Materials of Construction
BUNA-N -40 F to 250 F + These Options not Available with ATEX Models
Options A-F are applicable for Aluminum bodies only. 316 SS Pallet is
standard on all other body options.

Table F - Pressure Range & Load Table H - LOX (Liquid Oxygen) & LIN
Weight Material (Liquid Nitrogen) Cleaning, Trim
Option F Description Weight Option H Cleaning Trim
Material
0 Normal Standard
**Standard Pressure and
1 Lead 1 LOX Standard
Vacuum Setting = 0.5 oz/in2
2 LIN Standard
Over 2.9 oz/in2 to Maximum
2 Lead 5 Normal 316 Stainless Steel
Setting
3 > Standard to 2.9 oz/in2 Lead 6 LOX 316 Stainless Steel
4 **Standard Setting 316 SS 7 LIN 316 Stainless Steel
Over 2.9 oz/in2 to Maximum 8 Normal Monel
5 316 SS
Setting 9 LOX Monel
6 > Standard to 2.9 oz/in2 316 SS A LIN Monel
Incremental Weights Pressure For an ATEX Certified Valve choose Option 5, 6, 7. Trim includes Stem, Stem
7 Only 2.9 oz. - 14 oz. Lead Guides, Side Guides, Nuts, Bolts, and Screen.
(5 in. W.C. - 24 in. W.C.) NOTE: LOX/LIN cleaning for Cryogenic Breathers of aluminum construction
includes degreasing before assembly only!
Standard Incremental Weight
Set Pressure Only 6” -16” W.C. in
8 Lead
1” Increments Including (1)-1/2
In. and (2)-1/4 In. W.C. Weights
**Expanda-Seal min. pressure setting: 1.5 oz/in2

5911 Butterfield Road Hillside, IL 60162 • tel: (708) 236-6000 • fax: (708) 236-6006
Rev: 94020-3L
sales@ljtechnologies.com • www.ljtechnologies.com • ISO 9001: 2015 Certified