The document summarizes a needle valve model NFCC from Sun Hydraulics. It has a maximum flow rate of 7 gpm and works at pressures up to 5000 psi. It uses a handknob or screw adjustment to control flow through a fully adjustable orifice from fully closed to a maximum diameter of 0.19 inches. Various seal materials are available including Buna-N, EPDM, Viton and Polyurethane.
The document summarizes a needle valve model NFCC from Sun Hydraulics. It has a maximum flow rate of 7 gpm and works at pressures up to 5000 psi. It uses a handknob or screw adjustment to control flow through a fully adjustable orifice from fully closed to a maximum diameter of 0.19 inches. Various seal materials are available including Buna-N, EPDM, Viton and Polyurethane.
The document summarizes a needle valve model NFCC from Sun Hydraulics. It has a maximum flow rate of 7 gpm and works at pressures up to 5000 psi. It uses a handknob or screw adjustment to control flow through a fully adjustable orifice from fully closed to a maximum diameter of 0.19 inches. Various seal materials are available including Buna-N, EPDM, Viton and Polyurethane.
The document summarizes a needle valve model NFCC from Sun Hydraulics. It has a maximum flow rate of 7 gpm and works at pressures up to 5000 psi. It uses a handknob or screw adjustment to control flow through a fully adjustable orifice from fully closed to a maximum diameter of 0.19 inches. Various seal materials are available including Buna-N, EPDM, Viton and Polyurethane.
K Control Handknob Needle valves are fully adjustable orifices used to regulate flow. They are infinitely adjustable from fully closed up to C Maximum Orifice .19 in. (4,8 mm) the maximum orifice diameter. They are not pressure compensated and may be used as flow controls or as shutoff Diameter valves. N Seal Material Buna-N TECHNICAL DATA NOTE: DATA MAY VARY BY CONFIGURATION. SEE CONFIGURATION SECTION. (none) Material/Coating Standard Material/Coating Cavity T-13A Series 1 Capacity 7 gpm (.19 inch) Maximum Operating Pressure 5000 psi Adjustment - No. of CCW Turns from Fully Closed to Fully Open 5 Valve Hex Size 7/8 in. Valve Installation Torque 30 - 35 lbf ft Adjustment Screw Internal Hex Size 5/32 in. Locknut Hex Size 9/16 in. Locknut Torque 80 - 90 lbf in. Seal kit - Cartridge Buna: 990010007 Seal kit - Cartridge EPDM: 990010014 Seal kit - Cartridge Polyurethane: 990010002 Seal kit - Cartridge Viton: 990010006 Model Weight 0.40 lb.
NOTES For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.
CONFIGURATION OPTIONS Model Code Example: NFCCKCN
CONTROL (K) MAXIMUM ORIFICE DIAMETER (C) SEAL MATERIAL (N) MATERIAL/COATING K Handknob C .19 in. (4,8 mm) N Buna-N Standard Material/Coating L Standard Screw Adjustment D .09 in. (2,3 mm) E EPDM /AP Stainless Steel, Passivated H Calibrated Handknob with Detent Lock V Viton /LH Mild Steel, Zinc-Nickel Y Tri-Grip Handknob, Flow Control
c 2019 Sun Hydraulics
1 of 2 TECHNICAL FEATURES All 2-port flow control cartridges are physically and functionally interchangeable (i.e. same flow path, same cavity for a given frame size). However, cartridge extension dimensions from the mounting surface may vary. Because needle valves are non-compensating devices, the fixed orifice size will regulate flow through the valve in proportion to the square root of the pressure differential across ports 1 and 2. A balanced adjustment mechanism allows for easy adjustment even at high pressures. The sharp-edged orifice design minimizes flow variations due to viscosity changes. The flow path through this valve is bi-directional. The preferred path is port 1 to 2, to allow interchangeability with other flow controls. There is no leakage when the adjustment mechanism is turned to the shut-off position. Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
