6-Port Antenna

698-803 | 880-960 | 698-960 MHz

65° 2683 mm

5920370P
5920370PG 5920370PDx
3-Band, 6-Port, 65°, XPOL, Panel Antenna, Variable Tilt, 2683 mm +
Next Generation
 Tri band antenna, dual polarisation, 6 connectors
 Independent tilt on each band 2-10° / 2-10° / 2-12°
 Lightweight Twin+™, next generation TwinLine™ platform and low windload
 MET and RET versions, 3GPP/AISG2.0, in multiple single RET (multiple device type1) or in Multi-RET (device type 17, with firmware above MD3.10)
 Our patented RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

Frequency Range (MHz) 698-803 880-960 698-960

Array  R1  R2  R3
PRODUCT OVERVIEW

Connector 1-2 3-4 5-6

Polarization XPOL XPOL XPOL

Azimuth Beamwidth (avg) 65° 65° 65°

Electrical Downtilt 2-10° 2-10° 2-12°

Dimensions 2683 x 432 x 175 mm

ORDERING OPTIONS Select from the different options listed below

SELECT ELECTRICAL DOWNTILT SELECT SELECT CONNECTOR ANTENNA MODEL

CONTROL & AISG PROTOCOL ACTUATOR TYPE NUMBER

Manual Electrical Tilt (MET) --- 4.3-10 Female 5920370P

Multi-Device Control Unit

4.3-10 Female 5920370PG
(MDCU)
Remote Electrical Tilt (RET)
AISG v2.0 / 3GPP
Multi-Device Dual Unit
4.3-10 Female 5920370PDx*
(MDDU)

*Pre-commissioned configuration; Contact Amphenol for further details.

Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme
operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

CON N EC T I N G P E O P L E + T E C H N O L O G Y
REV062518I 1 of 6
www.amphenol-antennas.com
 6-Port Antenna
698-803 | 880-960 | 698-960 MHz
65° 2683 mm

5920370P
5920370PG 5920370PDx
3-Band, 6-Port, 65°, XPOL, Panel Antenna, Variable Tilt, 2683 mm

ELECTRICAL SPECIFICATIONS Low Band  R1

Frequency Range MHz 698-803
Polarization --- ±45°
Gain Over all Tilts dBi 15.2 ± 0.4
Azimuth Beamwidth degrees 73.5° ± 2.6°
Elevation Beamwidth degrees 8.9° ± 0.5°
Electrical Downtilt degrees 2°-10°
Impedance Ohms 50
VSWR --- < 1.5
Passive Intermodulation
dBm < -110
3rd Order for 2 x 20W Carriers
Front-to-Back Ratio, Total Power, ±30° dB > 23.7
Upper Sidelobe Horizon to 20° dB > 17.1
Suppression
Peak to 20° dB > 19.9
Cross Polar Ratio Main Direction (0°) dB > 21.8
Sector Edges (60°) dB > 11.7
Maximum Effective Power Per Port Watts 250
Inter/Intra Band Isolation dB > 25
Standard values based on NGMN-P-BASTA version 9.6 recommendation.

ELECTRICAL SPECIFICATIONS Low Band  R2

Frequency Range MHz 880-960
Polarization --- ±45°
Gain Over all Tilts dBi 16.3 ± 0.4
Azimuth Beamwidth degrees 68.3° ± 2.7°
Elevation Beamwidth degrees 7.2° ± 0.5°
Electrical Downtilt degrees 2°-10°
Impedance Ohms 50
VSWR --- < 1.5
Passive Intermodulation
dBm < -110
3rd Order for 2 x 20W Carriers
Front-to-Back Ratio, Total Power, ±30° dB > 24.0
Upper Sidelobe Horizon to 20° dB > 15.9
Suppression
Peak to 20° dB > 16.6
Cross Polar Ratio Main Direction (0°) dB > 14.1
Sector Edges (60°) dB > 10.0
Maximum Effective Power Per Port Watts 250
Inter/Intra Band Isolation dB > 25
Standard values based on NGMN-P-BASTA version 9.6 recommendation.
Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme
operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

CON N EC T I N G P E O P L E + T E C H N O L O G Y
REV062518I 2 of 6
www.amphenol-antennas.com
 6-Port Antenna
698-803 | 880-960 | 698-960 MHz
65° 2683 mm

5920370P
5920370PG 5920370PDx
3-Band, 6-Port, 65°, XPOL, Panel Antenna, Variable Tilt, 2683 mm

ELECTRICAL SPECIFICATIONS Low Band  R3

Frequency Range MHz 698-960

MHz 698-806 790-862 824-894 880-960

Polarization --- ±45°

Gain Over all Tilts dBi 15.3 ± 0.5 15.9 ± 0.3 16.2 ± 0.6 16.7 ± 0.4

Azimuth Beamwidth degrees 72.7° ± 2.3° 71.2° ± 3.7° 70.0° ± 3.7° 67.1° ± 2.9°

Elevation Beamwidth degrees 8.6° ± 0.7° 7.6° ± 0.4° 7.4° ± 0.4° 6.9° ± 0.5°

Electrical Downtilt degrees 2°-12°

Impedance Ohms 50

VSWR --- < 1.5

Passive Intermodulation
dBm < -110
3rd Order for 2 x 20W Carriers
Front-to-Back Ratio, Total Power, ±30° dB > 23.1 > 23.7 > 23.6 > 23.6

Upper Sidelobe Horizon to 20° dB > 16.1 > 15.1 > 15.1 > 13.6
Suppression
Peak to 20° dB > 17.9 > 18.7 > 17.2 > 14.5

Cross Polar Ratio Main Direction (0°) dB > 21.0 > 17.3 > 16.1 > 12.7

Sector Edges (60°) dB > 12.4 > 10.9 > 10.6 > 7.9

Maximum Effective Power Per Port Watts 250

Inter/Intra Band Isolation dB > 25

Standard values based on NGMN-P-BASTA version 9.6 recommendation.

Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme
operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

CON N EC T I N G P E O P L E + T E C H N O L O G Y
REV062518I 3 of 6
www.amphenol-antennas.com
 6-Port Antenna
698-803 | 880-960 | 698-960 MHz
65° 2683 mm

5920370P
5920370PG 5920370PDx
3-Band, 6-Port, 65°, XPOL, Panel Antenna, Variable Tilt, 2683 mm

ELECTRICAL DOWNTILT CONTROL

For multiband antennas, electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) A colored knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob color is identical
Control to the corresponding connector color. To access the knob, remove the cap by turning it counter-clockwise. It is
re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit
Remote Electrical Tilt (RET)
(MDDU) inserted in the bottom of the antenna. See details below and refer to the ordering options to see which
Control
actuators are available with this particular antenna. A single actuator individually controls the tilt of each band (no
need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET
control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna
still has manual tilt control (manual override). Do not remove the transparent cap(s) from the antenna.

RET ACTUATOR
Amphenol's RET-READY antennas are delivered with the RET Actuator already installed and pre-commissioned with all antenna parameters. Every
RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for
further installation of RET devices or for programming their configuration or for running a calibration process.

RET-READY Multi-Device Control Unit (MDCU). The MCDU is an electronic module that allows the remote control of the electrical downtilt (RET)
ACTUATORS in Amphenol antennas with factory embedded motors. The MDCU is factory installed. Refer to the ORDERING OPTIONS for
availability with this model.

Multi-Device Dual Unit (MDDU). The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). The MDDU is factory installed. Refer to the ORDERING
OPTIONS for availability with this model.

Number of RET-READY Actuators One per antenna

Input Voltage +10 to +30 V

Power Consumption Idle State (AISG P1) 0.5 W

High Power Mode (AISG P2) 3W

Protocol 3GPP/AISG 2.0

Tilt Change Duration Less than 15 seconds, typical (may vary dependent on antenna type and outdoor temperature)

Precision ±0.5°

Tilt Change Capability 50,000 minimum

MDCU One pair of AISG Male and Female (type IEC60130-9)

RET Interface
MDDU Two male AISG 8 pin connectors (type IEC60130-9 Ed 3.0)

Field Replaceable Unit Yes

Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme
operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

CON N EC T I N G P E O P L E + T E C H N O L O G Y
REV062518I 4 of 6
www.amphenol-antennas.com
 6-Port Antenna
698-803 | 880-960 | 698-960 MHz
65° 2683 mm

5920370P
5920370PG 5920370PDx
3-Band, 6-Port, 65°, XPOL, Panel Antenna, Variable Tilt, 2683 mm

Top

R1

R3

ARRAY FREQUENCY CONNECTOR CONNECTOR TYPE

ARRAY LAYOUT

R2
 R1 698-803 1-2 4.3-10 Female Long Neck

Left Right
 R2 880-960 3-4 4.3-10 Female Long Neck Bottom

 R3 698-960 5-6 4.3-10 Female Long Neck

Diagram shown at right depicts the view from the front of the antenna.
The illustration is not shown to scale.

MECHANICAL SPECIFICATIONS
Length mm (in) 2683 (105.6)
Width mm (in) 432 (17.0)
Depth mm (in) 175 (6.9)
Net Weight - Antenna Only kg (lbs) 37.5 (82.7)
Mechanical Distance Between Mounting Points mm (in) 1865 (73.4)
Windload Calculation km/h (mph) 150 (93.2)
(EN 1991-1-4:2005 using
Frontal N (lbf) 834 (187.5)
Wind Tunnel Coefficients)
Lateral N (lbf) 438 (98.5)
Rearside N (lbf) 950 (213.6)
Operational Wind Speed km/h (mph) 160 (99.4)
Survival Wind Speed km/h (mph) 200 (124)
Radome Color --- Gray RAL7035
Radome Material --- Outdoor Fibreglass
Lightning Protection --- Direct Ground

Shipping Dimensions (Length x Width x Depth) mm (in) 2930 x 550 x 280 (115.4 x 21.7 x 11.0)
Shipping

Shipping Weight kg (lbs) 50.5 (111.3)

Shipping Volume m3 (ft3) 0.45 (15.9)

Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme
operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

CON N EC T I N G P E O P L E + T E C H N O L O G Y
REV062518I 5 of 6
www.amphenol-antennas.com
 6-Port Antenna
698-803 | 880-960 | 698-960 MHz
65° 2683 mm

5920370P
5920370PG 5920370PDx
3-Band, 6-Port, 65°, XPOL, Panel Antenna, Variable Tilt, 2683 mm

ENVIRONMENTAL SPECIFICATIONS
Environmental --- ETS 300 019
Operating Temperature ° C (° F) -40° to +60° (-40° to +140°)
Product Environmental Compliance --- Product is RoHs Compliant

ACCESSORIES All accessories are ordered separately unless otherwise indicated

ITEM MODEL NUMBER WEIGHT

Brackets for pole Ø48 to Ø115 mm (Ø1.9 to Ø4.5 in) delivered as standard 0900181/00 3.4 kg (7.5 lbs)
Brackets for pole Ø70 to Ø150 mm (Ø2.8-Ø5.9 in) optional 0900182/00 3.9 kg (8.6 lbs)
Kit to add mechanical tilt (0° to 10°) to above brackets optional 0900397/00 3.0 kg (6.6 lbs)
Wall mounting brackets are available upon request

Dimensions shown in mm
INSTALLATION Please read all installation notes before installing this product.

Always attach the antenna by all mounting points.

Do not install the antenna with the connectors facing upwards.

Do not cut the tethered transparent cap(s) that cover the

antenna's tilt adjustment indicators.
In order to operate the RET control, the transparent caps
covering the tilt adjustment indicators must be engaged and
locked.
2683 mm
1865 mm
210 mm

175
432 mm

Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme
operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

CON N EC T I N G P E O P L E + T E C H N O L O G Y
REV062518I 6 of 6
www.amphenol-antennas.com