8-Port Antenna R1 R2 B1 B2

Frequency Range 790–960 790–960 1710–2180 1710–2180

Dual Polarization X X X X
HPBW 65° 65° 60° 60°
Adjust. Electr. DT 0°–8° 0°–8° 0°–6° 0°–6°
set by hand or by optional RCU (Remote Control Unit)

8-Port Antenna 790–960/790–960/1710–2180/1710–2180 65°/65°/60°/60° 17/17/18.5/18.5dBi

0°–8°/0°–8°/0°–6°/0°–6°T
Type No. 80010826
Lowbands R1 R2
790 – 960 790 – 960
Frequency Range MHz 790 – 862 824 – 894 880 – 960 790 – 862 824 – 894 880 – 960
Gain at mid Tilt dBi 16.6 16.8 16.7 16.5 16.8 16.8
Gain over all Tilts dBi 16.5 ± 0.3 16.6 ± 0.2 16.6 ± 0.3 16.5 ± 0.4 16.6 ± 0.2 16.6 ± 0.3
Horizontal Pattern:
Azimuth Beamwidth ° 65 ± 2.3 64 ± 2.0 62 ± 2.4 66 ± 2.8 64 ± 2.2 63 ± 2.5
Front-to-Back Ratio, dB
> 26 > 27 > 28 > 25 > 26 > 27
Total Power, ± 30°
Cross Polar Discrimination dB
> 31 > 32 > 29 > 30 > 30 > 29
at Boresight
Cross Polar Discrimination dB
> 15.0 > 13.5 > 12.0 > 15.0 > 14.0 > 11.5
over Sector
Azimuth Beam dB
< 1.5 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth ° 8.1 ± 0.3 7.9 ± 0.3 7.5 ± 0.3 8.0 ± 0.3 7.8 ± 0.3 7.5 ± 0.3
Electrical Downtilt °
0.0 – 8.0 0.0 – 8.0
continuously adjustable
Tilt Accuracy ° < 0.2 < 0.2 < 0.3 < 0.2 < 0.2 < 0.3
First Upper Side Lobe dB
> 16 > 17 > 16 > 16 > 17 > 16
Suppression
Cross Polar Isolation dB > 30 > 30
Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)
Max. Effective Power W 400 (at 50 °C ambient temperature) 400 (at 50 °C ambient temperature)
per Port
Values based on NGMN-P-BASTA (version 9.6) requirements.
936.4887/b ngmn 04.19.02.00 Subject to alteration.

www.kathrein.com 80010826 Page 1 of 4

KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
8-Port Antenna

Highbands B1 B2
1710 – 2180 1710 – 2180
Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2180 1710 – 1880 1850 – 1990 1920 – 2180
Gain at mid Tilt dBi 18.4 18.5 18.4 18.4 18.6 18.6
Gain over all Tilts dBi 18.3 ± 0.3 18.4 ± 0.4 18.2 ± 0.5 18.3 ± 0.4 18.5 ± 0.5 18.4 ± 0.5
Horizontal Pattern:
Azimuth Beamwidth ° 60 ± 2.4 57 ± 2.5 59 ± 3.4 60 ± 2.9 57 ± 2.1 58 ± 3.2
Front-to-Back Ratio, dB
> 26 > 25 > 24 > 25 > 26 > 26
Total Power, ± 30°
Cross Polar Discrimination dB
> 28 > 28 > 24 > 28 > 27 > 24
at Boresight
Cross Polar Discrimination dB
> 16.0 > 15.5 > 10.0 > 15.0 > 14.5 > 9.5
over Sector
Azimuth Beam dB
< 0.5 < 1.0 < 1.5 < 0.5 < 1.0 < 1.5
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth ° 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4
Electrical Downtilt °
0.0 – 6.0 0.0 – 6.0
continuously adjustable
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.3 < 0.2 < 0.2
First Upper Side Lobe dB
> 14 > 14 > 14 > 14 > 15 > 15
Suppression
Cross Polar Isolation dB > 30 > 30
Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)
Max. Effective Power W 250 (at 50 °C ambient temperature) 250 (at 50 °C ambient temperature)
per Port
Values based on NGMN-P-BASTA (version 9.6) requirements.

936.4887/b ngmn 04.19.02.00 Subject to alteration.

Page 2 of 4 80010826 www.kathrein.com

KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
 8-Port Antenna

Electrical specifications, all systems Mechanical specifications

Impedance Ω 50 Input 8 x 7-16 female
VSWR < 1.5 Connector Position bottom
Return Loss dB > 14 Adjustment Mechanism 4x, Position bottom
Interband Isolation dB > 30 continuously adjustable
Passive Intermodulation dBc < –150 (2 x 43 dBm carrier) Wind load (at Rated N | lbf Frontal: 1550 | 348
Polarization ° –45, +45 Wind Speed: 150 km/h) Maximal: 1705 | 383
Max. Effective Power 1200 (at 50 °C ambient Max. Wind Velocity km/h 200
W temperature) mph 124
for the Antenna
Values based on NGMN-P-BASTA (version 9.6) requirements. Height / Width / Depth mm 2399 / 576 / 133
inches 94.4 / 22.7 / 5.2
Category of H (Heavy)
Mounting Hardware
Weight kg 39.0 / 41.2 (clamps incl.)
lb 86.0 / 90.8 (clamps incl.)
Packing Size mm 2576 / 600 / 170
inches 101.4 / 23.6 / 6.7
Scope of Supply Panel and 2 units of clamps
for 42 – 115 mm |
1.7– 4.5 inches diameter

Accessories (order separately if required) 1) 2) 1) ’ 9 | 0.4

2) 72 | 2.8
Remarks Weight approx. Units per
Type No. Description mm | inches kg | lb antenna

85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
85010008 1 downtilt kit Downtilt angle: 0° – 9° 4.3 | 9.5 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
936.4887/b ngmn 04.19.02.00 Subject to alteration.

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
2399 | 94.4
2432 | 95.7
2472 | 97.3

Wall mounting with two half clamps 738546 (included in the scope of supply).

Material: Reflector screen: Weather-proof aluminum.

Fiberglass radome: The grey fiberglass radomes of these antennas
are very stable and extraordinarily stiff. They are resistant to ultraviolet
radiation and can also be painted to match their surroundings.
All screws and nuts: Stainless steel

Grounding: The metal parts of the antenna including the mounting and the inner
conductors are DC grounded.

Adjustment mechanism
with integrated scale

All dimensions in mm | inches

Any previous data sheet issues have now become invalid. 80010826 Page 3 of 4
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
8-Port Antenna

Layout of interface:

790-960 -2180 Til ilt

790-96 1710-218
10

0
T

0
Tilt

t
17

99 | 3.9
110 | 4.3
Tilt

133 | 5.2 *
4)
56 | 2.2

34 | 1.3
1) 2)

270 | 10.6 3)
1) 33.5 | 1.3
476 | 18.7 2) 35.5 | 1.4
3) 50 | 2.0
576 | 22.7 * 4) 45 | 1.8
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches

Correlation Table
Frequency range Array Connector
936.4887/b ngmn 04.19.02.00 Subject to alteration.

790– 960 MHz R1 1–2

790– 960 MHz R2 3–4
1710–2180 MHz B1 5–6
1710–2180 MHz B2 7–8

B1 B2
R1 R2
Left Right

Page 4 of 4 80010826 Any previous data sheet issues have now become invalid.
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
 Mounting Hardware
Clamp Included in the Scope of Supply

Suitable for mast diameter (mm) 42 – 115

[inches] [1.65 – 4.53]
Antenna – mast distance (mm) 20 – 25
[inches] [0.79 – 0.98]
Material of clamp and screws Hot-dip galvanized steel / stainless steel
Weight (kg) 1.1
[lb] [2.43]

152 [5.98]

100 [3.94]

[0.79–0.98]
40 [1.57]
72 [2.83]

20–25
40 [1.57]

15
2–1
’ 4 4.53]
5–
[1.6

M10 ‰MA = 25 Nm

M8 ‰MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]

20–25
[0.79–0.98]
Subject to alteration.
936.3920/c

Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.

Any previous data sheet issues have now become invalid. 738546 Page 1 of 1
www.kathrein.de
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
 General Instructions
for Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

1
2

2
➀ Twist protection. ➀ Thread for fixing the protective To set the downtilt angle exactly,
➁ Downtilt spindle with integrated cap or the RCU (Remote Control you must look horizontally at the
scale. Unit). scale. The lower edge of the gear-
➁ Gearwheel for RCU power drive. wheel must be used for alignment.

Manual adjustment procedure:

0° – max.°

0° – max.°

Remove the protective cap and the Set downtilt angle by rotating the Screw on the twist protection and
twist protection completely. gearwheel. the protective cap again.

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

Subject to alteration.
936.4037/a

For a description of RCU installation please refer to the respective data sheet.
www.kathrein.com Page 1 of 2
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
General Instructions
for Feederline and RCU Installation
for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.

Description of bottom end cap (exemplary picture):

Adjustment mechanism
(protective cap removed) Ventilation hole

Spindle with tilting scale

Colour coding:
Correlation of each RF input to:
– the corresponding adjustment mechanism
7-16 female (long neck) – the frequency range
– the polarization

Installation of the feederline connector and RCU (optional):

In order to protect the adjustment mechanism, the protective caps have to be attached during
feederline installation!
Kathrein installation set: Type No. 85010077
Set has to be ordered separately!
Set consists of three spanners of divers width
27, 32 and 41 mm | 1.1, 1.3 and 1.6 inches
1/2˝ square actuation
according to
DIN 3120 Form C

32 | 1.3
Subject to alteration.

Carefully place the connector and After feederline installation, the

fix the nut using a torque-wrench optional remote control units
(according to the manufacturers (RCUs) can be mounted. .6
|1
27

guidelines). 41
| 1.
1

All dimensions in mm | inches

936.4037/a

These tools are suitable for 7-16 connectors with a wrench size of
27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a
wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on
connector manufacturers’ specifications, respectively the RCU nut
with a torque range of 15 – 18 Nm.

Page 2 of 2 Any previous data sheet issues have now become invalid.
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
 General Information
about Panel Antennas

Environmental Kathrein cellular antennas are designed to operate under the environmental ­conditions
­conditions: as described in ETS 300 019-1-4 class 4.1 E.
The antennas exceed this standard with regard to the following items:
– Low temperature: –55 °C
– High temperature (dry): +60 °C
For antennas equipped with FlexRET: The electrical downtilt adjusting is designed to
operate under the environmental conditions as described in the valid data sheet of the
FlexRET.

Ice protection: Due to the very sturdy antenna construction and the ­protection of
the radiating system by the r­adome, the antenna remains operational even under icy
­conditions.

Environmental Kathrein antennas fulfil the stated specifications after completion of the environmental
tests: tests as defined in ETS 300 019-2-4. The homogenous d ­ esign of Kathrein’s antenna
­families uses ­identical modules and materials.
Extensive tests have been performed on typical samples and modules. The vibration
test has been adapted relating to frequency and acceleration to the conditions of mast
mounted antennas.

Please note: As a result of more stringent legal regulations and judgements regarding product
liability, we are obliged to point out certain risks that may arise when products are
used under extraordinary ­operating conditions.

The mechanical design is based on the environmental conditions as ­stipulated in

ETS 300 019-1-4. Wind loads are ­calculated according to ­DIN 1055-4.
The antennas may be used at locations where the anticipated peak wind velocity or
gust wind speed lies within the maximum wind speed listed in the data sheet. We
warrant the mechanical s­afety and electrical functionality under such conditions.
­
The wind speeds are defined in ­accordance with the DIN, EN or TIA standards. This
­warranty makes ­allowance for the partial safety factors specified in those standards.
Extraordinary ­operating conditions, such as heavy icing or exceptional d ­ ynamic stress
(e.g. strain caused by oscillating support structures), may result in the b
­ reakage of an
­antenna or even cause it to fall to the ground. These facts must be c ­ onsidered during
the site planning process.

The details given in our data sheets have to be f­ ollowed carefully when i­nstalling
the antennas and a ­ ccessories.
Site planning and installation must be carried out by qualified and ­experienced
staff. All relevant national safety regulations must be upheld and respected.
­Incorrect site planning, faulty installation, as well as i­nterfering surroundings
on site, may lead to deviations in the ­electrical parameters compared to those
­specified in the respective data sheets.
The connectors on this product are only suitable for connecting to the ­compatible
counterpart. Please ensure that the connected cable has been ­ fitted with a
­connector of the same standard, otherwise damage may occur.

The tilt values will be set to any arbitrary value in the given tilt range. These values
Subject to alteration.

are independent from the frequency band or antenna type and can vary between
antennas and bands.

EU-RED Hereby, Kathrein Werke KG declares that the radio equipment is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at
the following internet address: http://www.kathrein.com
936.4694/d

Our quality assurance system and our RoHS Our products are compliant to the
environmental management system apply EU Directive RoHS as well as to other
to the entire company and are certified environmentally relevant regulations
by TÜV according to EN ISO 9001 and (e.g. REACH).
EN ISO 14001.

Any previous data sheet issues have now become ­invalid. Page 1 of 1
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820