Morse Test On Multi Cylinder Petrol Engine

MORSE TEST ON MULTI CYLINDER PETROL ENGINE
(AMBASSADOR ENGINE)
AIM:
To perform the Morse test on the given multi cylinder petrol engine and to
determine the efficiency at the given load
APPARATUS REQUIRED:
1. Multi Cylinder Petrol Engine Test Rig
2. Tachometer
3. Stop watch
SPECIFICATIONS:
Engine : Multi cylinder, ambassador engine
Type : water cooled, 4-s petrol engine.
Rated power : 32 kW @ 3200 rpm
Rated idling speed (N) : 650 rpm - 3500 rpm
Bore Diameter (D) : 73.02 mm
Stroke Length (L) : 88.9 mm
Compression Ratio : 9:2:1
Fuel : Petrol
Calorific value of petrol (CV) : 47,200 KJ/Kg
DESCRIPTION OF TEST RIG:

The petrol engine is a 4 cylinder, four strokes, water cooled, vertical type coupled
with electrical dynamometer. The fuel consumption of the engine is measured with a
burette, fitted on the fuel line. The consumption rate of the air is measured with the help
New No. 3, Old no. 2, S.V . Koil Street, Sekar Nagar, Ashok Nagar, Chennai – 600 083
Phone: +91 (044) 4351 8677 | Cell: (+91) 9789976777
Email: sales@elshaddaiengg.com, support@elshaddaiengg.com www.elshaddaiengg.com
of air tank fitted with an orifice. The air tank is connected with the engine inlet manifold
through a flexible pipe.
BRAKE POWER :
BP = (2πNT) / 60
Where,
T = Brake Torque (W * L)
W – Load in Newton
L – Distance between shaft axis and the point of suspension
N - Rpm.
FORMULAE:
Brake power when all cylinders are working, BP 1234 = ( 2πNT1234 )/ (60*1000) KW.
Where, T is the torque developed in N-m
Brake power when first cylinder is cutoff, BP234 = ( 2πNT234) / (60*1000) KW.
Brake power when second cylinder is cutoff, BP134 = ( 2πNT134) / ( 60*1000) KW.
Brake power when third cylinder is cutoff, BP124 = ( 2πNT124) / (60*1000) KW.
Brake power when fourth cylinder is cutoff, BP123 = ( 2πNT123) / (60*1000) KW.
Indicated power of the first cylinder IP1 = (BP1234) – (BP234) KW
Indicated power of second cylinder IP2 = ( BP1234) – (BP134) KW
Indicated power of third cylinder IP3 = ( BP1234) – (BP124) KW.
Indicated power of fourth cylinder IP4 = ( BP1234) - ( BP123) KW.
IP1234 = IP1+IP2+IP3+IP4
Mechanical efficiency (ηм) = {( BP1234) / (IP1234)} * 100 %
Phone: +91 (044) 4351 8677 | Cell: (+91) 9789976777
PROCEDURE:
 Before starting the engine keep the fuel cut off level in ON position.
 Start the engine using starter motor.
 Allow the engine to run at no load for about 10 minutes to warm up and attain
steady state condition.
 Load the engine to the required level.
 When the engine is loaded to the required load adjust the throttle to maintain the
speed of the engine at its rated rpm.
 Allow few minutes for the engine attains steady state condition and note down the
load when all the cylinders are developing power.
 Cut off cylinder no.1 by lifting the cutoff switch no.1
 Bring the engine again to rated speed by adjusting the load on brake drum and not
by adjusting the throttle and note down the corresponding load on the engine.
 Similarly cut off the cylinder.2,3,4 and repeat the above procedure to find the load
on the engine for cylinder.
 Remove the load from the engine and stop the engine by switching off the ignition
switch.
PRECAUTIONS:
 The engine should not be started or stopped under loaded condition.
 The lubricating oil level should be ensured before starting the engine.
 The engine cooling water supply should be ensured before starting the engine.
Phone: +91 (044) 4351 8677 | Cell: (+91) 9789976777
OBSERVATION:
Ambient temperature (Ta) = ºC
S.No Conditions Load Speed B.P

in kg (Rpm) (KW)
1 All cylinders are
working
2 First cylinder is cut
off remaining are
working
3 Second cylinder is
cut off remaining are
working
Third cylinder is cut
4 off remaining are
working
5 Fourth cylinder is cut
off remaining are
working
RESULT:
The Morse test on the given 4-stroke engine has been conducted and results are
obtained.
Phone: +91 (044) 4351 8677 | Cell: (+91) 9789976777

Morse Test On Multi Cylinder Petrol Engine

Uploaded by

Copyright:

Available Formats

Morse Test On Multi Cylinder Petrol Engine

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Morse Test On Multi Cylinder Petrol Engine

Uploaded by

Copyright:

Available Formats

MORSE TEST ON MULTI CYLINDER PETROL ENGINE

Type : water cooled, 4-s petrol engine.

Rated power : 32 kW @ 3200 rpm

Rated idling speed (N) : 650 rpm - 3500 rpm

Bore Diameter (D) : 73.02 mm

Stroke Length (L) : 88.9 mm

Compression Ratio : 9:2:1

Calorific value of petrol (CV) : 47,200 KJ/Kg

DESCRIPTION OF TEST RIG:

L – Distance between shaft axis and the point of suspension

Where, T is the torque developed in N-m

Indicated power of the first cylinder IP1 = (BP1234) – (BP234) KW

Indicated power of second cylinder IP2 = ( BP1234) – (BP134) KW

Indicated power of third cylinder IP3 = ( BP1234) – (BP124) KW.

Indicated power of fourth cylinder IP4 = ( BP1234) - ( BP123) KW.

 The engine should not be started or stopped under loaded condition.

Ambient temperature (Ta) = ºC

S.No Conditions Load Speed B.P

You might also like