User Manual: DPG-2201-00X Digital Governor

User Manual
DPG-2201-00X
Digital Governor
APECS® Programmable Governors for

Isochronous Generators with
Load Sharing Capability
Manual 36523A
WARNING
Read this entire manual and all other publications pertaining to the work to be
performed before installing, operating, or servicing this equipment. Practice all
plant and safety instructions and precautions. Failure to follow instructions can
cause personal injury and/or property damage.
The engine, turbine, or other type of prime mover should be equipped with an
overspeed shutdown device to protect against runaway or damage to the prime
mover with possible personal injury, loss of life, or property damage.
The overspeed shutdown device must be totally independent of the prime mover
control system. An overtemperature or overpressure shutdown device may also be
needed for safety, as appropriate.
CAUTION
To prevent damage to a control system that uses an alternator or battery-charging
device, make sure the charging device is turned off before disconnecting the
battery from the system
In systems where large inductive loads are switched on the DC power buss, surge
impulse energy will be present due to the switching. To address surge energy
affects on the control, appropriate suppression devices must be installed in the DC
power buss prior to the control’s power connection.
Electronic controls contain static-sensitive parts. Observe the following

precautions to prevent damage to these parts.
• Discharge body static before handling the control (with power to the control
turned off, contact a grounded surface and maintain contact while handling the
control).
• Avoid all plastic, vinyl, and Styrofoam (except antistatic versions) around
printed circuit boards.
• Do not touch the components or conductors on a printed circuit board with
your hands or with conductive devices.
IMPORTANT DEFINITIONS
WARNING—indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION—indicates a potentially hazardous situation which, if not avoided, could

result in damage to equipment.
NOTE—provides other helpful information that does not fall under the warning or
caution categories.
Revisions—Text changes are indicated by a black line alongside the text.
Woodward Governor Company reserves the right to update any portion of this publication at any
time. Information provided by Woodward Governor Company is believed to be correct and
reliable. However, no responsibility is assumed by Woodward Governor Company unless
otherwise expressly undertaken.
© Woodward 2005
All Rights Reserved
Manual 36523A DPG-2201-00X Digital Governors
Contents
ELECTROSTATIC DISCHARGE AWARENESS ................................................. III

CHAPTER 1. GENERAL INFORMATION .......................................................... 1
Introduction............................................................................................................ 1
CHAPTER 2. GOVERNOR SPECIFICATIONS ................................................... 2
Electrical ................................................................................................................ 2
Mechanical ............................................................................................................ 2
Performance .......................................................................................................... 2
User Interface Operation ....................................................................................... 3
Operating Modes ........................................................................................... 3
Keypad........................................................................................................... 4
LED Display ................................................................................................... 6
CHAPTER 3. PARAMETER REFERENCE......................................................... 8
DPG-2201-00X Parameter List ............................................................................. 9
3.1 No. of Flywheel Teeth (optional)........................................................... 10
3.2 Set Speed A (required)......................................................................... 10
3.3 Set Speed B (optional) ......................................................................... 11
3.4 Idle Speed (optional)............................................................................. 11
3.5 Proportional (required).......................................................................... 12
3.6 Integral (required) ................................................................................. 12
3.7 Derivative (required) ............................................................................. 13
3.8 OVG @ Set Speed A (required) ........................................................... 13
3.9 OVG @ Set Speed B (optional)............................................................ 13
3.10 OVG @ Idle Speed (optional)............................................................. 13
3.11 Gain Factor (required) ........................................................................ 13
3.12 Speed Filter (required)........................................................................ 14
3.13 Idle Hold Time (optional) .................................................................... 14
3.14 Accel Rate (optional) .......................................................................... 14
3.15 Decel Rate (optional).......................................................................... 15
3.16 Startup Rate (optional) ....................................................................... 15
3.17 Startup Limit (optional) ....................................................................... 16
3.18 Torque Limit (optional)........................................................................ 16
3.19 Integral Low Limit (optional) ............................................................... 17
3.20 Integral High Limit (optional)............................................................... 17
3.21 Percent Droop (optional) .................................................................... 18
3.22 No Load Calibration (optional)............................................................ 18
3.23 Full Load Calibration (optional)........................................................... 18
3.24 Password (optional) ............................................................................ 19
3.25 Over Speed Limit (optional)................................................................ 19
3.26 Set Speed A Min (optional)................................................................. 20
3.27 Set Speed A Max (optional)................................................................ 20
3.28 Set Speed B Min (optional)................................................................. 20
3.29 Set Speed B Max (optional)................................................................ 20
3.30 Idle Speed Min (optional).................................................................... 20
3.31 Idle Speed Max (optional)................................................................... 20
3.32 Duty Cycle Limit (optional).................................................................. 20
3.33 Startup Speed (optional)..................................................................... 21
3.34 Startup Duty Cycle (optional).............................................................. 21
Woodward i
CHAPTER 4. UNIVERSAL PST.................................................................... 23

Introduction .................................................................................................. 23
Features....................................................................................................... 23
System Requirements ................................................................................. 23
Acquiring Universal PST.............................................................................. 24
Installing Universal PST............................................................................... 25
Wiring the COMM Port to a PC ................................................................... 25
Communications Error ................................................................................. 26
Universal PST User Interface Overview ...................................................... 26
Universal PST Menu Items .......................................................................... 28
Parameter Setup.......................................................................................... 28
Parameter Help............................................................................................ 29
Synchronizing Universal PST with a DPG................................................... 29
Status View.................................................................................................. 29
Tuning View ................................................................................................. 30
Chart Recorder ............................................................................................ 30
Engine Speed Data Collection..................................................................... 31
CHAPTER 5. CALIBRATION INSTRUCTIONS ................................................. 32
Basic Adjustments ............................................................................................... 32
Tuning Methodology ............................................................................................ 32
Droop Calibration Procedure............................................................................... 33
CHAPTER 6. INSTALLATION INSTRUCTIONS ................................................ 35
Terminal Descriptions.......................................................................................... 35
Recommended Mounting .................................................................................... 35
Wiring Diagram.................................................................................................... 36
DPG-2201-001 & DPG-2201-002................................................................ 36
CHAPTER 7. DIAGNOSTICS & TROUBLESHOOTING ..................................... 37
Display Codes ..................................................................................................... 37
Troubleshooting Table......................................................................................... 37
CHAPTER 8. SERVICE OPTIONS ................................................................. 39
Product Service Options...................................................................................... 39
Replacement/Exchange............................................................................... 39
Flat Rate Repair........................................................................................... 40
Flat Rate Remanufacture............................................................................. 40
Returning Equipment for Repair.......................................................................... 40
Packing a Control ........................................................................................ 40
Return Authorization Number ...................................................................... 41
Replacement Parts .............................................................................................. 41
How to Contact Woodward.................................................................................. 41
Engineering Services........................................................................................... 42
Technical Assistance........................................................................................... 43
Woodward ii
Electrostatic Discharge Awareness

All electronic equipment is static-sensitive, some components more than others.
To protect these components from static damage, you must take special
precautions to minimize or eliminate electrostatic discharges.
Follow these precautions when working with or near the control.
1. Before doing maintenance on the electronic control, discharge the static

electricity on your body to ground by touching and holding a grounded metal
object (pipes, cabinets, equipment, etc.).
2. Avoid the build-up of static electricity on your body by not wearing clothing
made of synthetic materials. Wear cotton or cotton-blend materials as much
as possible because these do not store static electric charges as much as
synthetics.
3. Keep plastic, vinyl, and Styrofoam materials (such as plastic or Styrofoam

cups, cup holders, cigarette packages, cellophane wrappers, vinyl books or
folders, plastic bottles, and plastic ash trays) away from the control, the
modules, and the work area as much as possible.
4. Do not remove the printed circuit board (PCB) from the control cabinet
unless absolutely necessary. If you must remove the PCB from the control
cabinet, follow these precautions:
• Do not touch any part of the PCB except the edges.
• Do not touch the electrical conductors, the connectors, or the

components with conductive devices or with your hands.
• When replacing a PCB, keep the new PCB in the plastic anti-static
protective bag it comes in until you are ready to install it. Immediately
after removing the old PCB from the control cabinet, place it in the anti-
static protective bag.
CAUTION
To prevent damage to electronic components caused by improper handling,
read and observe the precautions in Woodward manual 82715, Guide for
Handling and Protection of Electronic Controls, Printed Circuit Boards, and
Modules.
Woodward iii
Chapter 1.
General Information
Introduction
This manual provides information on the following DPG controllers:
DPG-2201-001 and DPG-2201-002
The DPG-2201-00X digital governor is used primarily to govern diesel or gas

fueled engines of generator sets. This microprocessor based, digital controller
performs across a wide speed range and allows adjustment of all governor
features through the built-in user interface. Properly tuned, this governor delivers
fast engine response to speed or load changes while providing precise stable
isochronous operation.
Separately programmable Proportional, Integral, and Derivative gains are

provided for tailoring governor response to many engine applications. Other
adjustments include acceleration and deceleration ramp rates, startup and torque
limits, idle speed and idle hold time.
This governor can also provide droop speed control with 100 user selectable
droop levels. The governor’s internal FAILSAFE reacts instantly to loss of the
engine speed signal or loss of remote speed potentiometer signal.
Features include:
• Automatic calibration of the remote speed potentiometer
• Isochronous speed control
• Droop operation: 0 to 10% of set speed with 1/10 percent resolution
• User friendly / operator adjustable
• Precision frequency control: 0.25%
• Superior temperature stability
• Reverse battery protection
• Input voltage range: 9–30 Vdc
• Smoke control on start up
• Remote setup
• Serial communication port
Actuator Compatibility:
DYNA 2000 DYNA 7000 DYNA 8000 APECS 0150

DYNA 2500 DYNA 70025 DYNA 8200 APECS 0250
DYNA 10141 DYNA 8400 APECS 0300
Power Flow Series Gas Valves
APECS Linkage Free Integral Type
Other Models Available:
DPG-2100 Series – for Genset Applications

DPG-2300 Series – for Off-Road Vehicles
DPG-2400 Series – for EFC Valve Applications
Woodward 1
Chapter 2.
Governor Specifications
The governor’s main electrical and mechanical specifications are listed here
along with several performance characteristics.
Electrical
Operating Voltage Range: 9–30 Vdc *
Rated Output Current: 7 A Maximum (continuous)
Maximum Surge Current: 14 A (not to exceed ten seconds)
Connections: Terminal strip with 13 terminals
Input Signal from the Magnetic Pickup: 2.0 VAC RMS minimum during cranking
(*) DC power buss cable cannot be longer than 10 meters (32.80 feet)
Mechanical
Ambient Operating Temperature: -40°F to +185°F (-40°C to +85°C)
Oil, water, and dust resistant via conformal
Sealing:
coating and die cast enclosure
Weight: 12 oz. (341 g)
Connections: 13-terminal Euro-style connector
Suitable for mounting per SAE J1455;
Mechanical Vibration:
1 to 500 Hz, 5G amplitude
Performance
Temperature Stability 0.007 Hz @ 158ºF (70°C)
± .25% over ambient operating temperature
Steady State Speed Band:
range
Engine Speed Measurement Range: 10 MPU Hertz to 14,000 MPU Hertz
Governing Speed Range: 500 MPU Hertz to 11,000 MPU Hertz
ILS Input Voltage Measurement Range: 2.375–2.625 Vdc
ILS Input Speed Adjust Range: ±3% around the set speed
Droop Adjustment Range: 0 to 10 percent of the set speed
Droop Setting Resolution: Tenths of a percent
Woodward 2
User Interface Operation

The user interface has two distinct behaviors that you should familiarize yourself
with in order to select parameters and adjust them. These behaviors are
described in the Operating Modes section below.
A 4-pushbutton keypad and a 2-digit LED display make up the built-in user
interface. The pushbuttons, also called keys, are described in the section named
Keypad. The LED display is described in the section named LED Display.
Remote access to the governor’s parameter settings is available when the

governor’s COMM port is connected to a computer running our Universal PST
application. The COMM port provides access to governor settings, allowing
adaptation to each application during service and initial configuration.
Operating Modes
The user interface operates in two modes: PARAMETER SELECT MODE and
PARAMETER EDIT MODE. For each of these modes, the keypad and the display
have a unique way of operating.
The following tables provide a quick reference to the behavior of the display and
the function of each key when a particular operating mode is active.
PARAMETER SELECT MODE is the mode used to select a parameter for viewing
and editing. This mode is active when the 2-digit value being displayed is blinking.
The value displayed is a parameter’s identification (ID) number. The controller’s
label lists each user-adjustable parameter and its corresponding ID number.
PARAMETER SELECT MODE

The ID number of a parameter listed on the
LED Display
governor’s label is blinking on and off
INC key Increase the parameter ID number by one
DEC key Decrease the parameter ID number by one
Activate PARAMETER EDIT MODE on the

SELECT key
parameter whose number was blinking
Display the version number of the

ENTER
governor’s programming
INC & DEC
Turn on all LED segments as a test
Simultaneously
PARAMETER EDIT MODE is the mode that displays the selected parameter’s
value and allows the value to be modified. This mode is active when the 2-digit
value displayed is on and no longer blinking. The value displayed is the selected
parameter’s current value. The display’s decimal points have several different
meanings while in PARAMETER EDIT MODE. These are described below.
• Decimal point blinking
The selected parameter’s value can be modified.
• Decimal point not blinking
The selected parameter’s value cannot be modified; parameter editing
is locked and values can only be viewed. This is the case when
password protection is active and the unlock code has not been
entered. Read about the Password parameter in the Parameter
Woodward 3
Reference chapter for more information about using password
protection.
• Right digit’s decimal point is blinking or ON
The lower two digits (the tens digit and the ones digit) of a
parameter’s 4-digit value are being displayed.
• Left digit’s decimal point is ON
The upper two digits (the thousands digit and the hundreds digit) of a
parameter’s 4-digit value are being displayed. The upper two digits of
a parameter are always view only and can never be modified directly.
The upper two digits change when the lower digits overflow (transition
from 99 to 00) or underflow (transition from 00 to 99).
PARAMETER EDIT MODE

The value of the selected parameter is
displayed. A blinking decimal point means
LED Display
the value can be modified; otherwise, the
value is view only.
INC key Increase the selected parameter’s value.
DEC key Decrease the selected parameter’s value.
Return to PARAMETER SELECT MODE

SELECT key and ignore changes made to the
parameter’s value
Save the parameter’s new value, and

ENTER
return to PARAMETER SELECT MODE
INC & DEC Use to display the upper digits of values

Simultaneously larger than 99
Keypad
The keypad consists of four pushbuttons named ENTER, SELECT, INC, and
DEC.
ENTER Key
The ENTER key is used to exit PARAMETER EDIT MODE and return to
PARAMETER SELECT MODE while saving the parameter’s new value to
nonvolatile memory. Nonvolatile memory is where parameter values are stored so
that they are remembered even when the governor is not being powered. In
PARAMETER SELECT MODE, pressing the ENTER key displays the version
number of the governor’s programming.
SELECT Key
The SELECT key is used to enter PARAMETER EDIT MODE from PARAMETER
SELECT MODE once a particular parameter has been selected for editing.
The SELECT key is also used to escape from PARAMETER EDIT MODE and
return to PARAMETER SELECT MODE without saving a change in a parameter’s
value. The value a parameter had when PARAMETER EDIT MODE was entered
is restored.
INC (increase) Key

The INC key is used to increase the displayed value.
Woodward 4
In PARAMETER SELECT MODE, each press of the INC key will cause the next
higher parameter identification number to be displayed. When the maximum
parameter identification number is reached, the next INC key press will cause the
first parameter ID number to be displayed.
For example: If the controller’s label lists 34 parameters, then pressing the
INC key when the display is blinking the value 34 will cause the display to
wrap around to the first parameter listed and begin blinking the value 01.
In PARAMETER EDIT MODE, each INC key press will increase a parameter’s
current value. If the INC key is held down while in PARAMETER EDIT MODE the
value will automatically continue to be increased at gradually faster and faster
rates until the INC key is released or the parameter’s maximum allowed value is
reached. When the lower two digits display a 99, pressing the INC (increase key)
will cause the lower two digits to display a 00 and the hundreds digit will have
been increased by 1.
DEC (decrease) Key

The DEC (decrease) key is used to decrease the displayed value.
In PARAMETER SELECT MODE, each press of the DEC key will cause the next
lower parameter number to be displayed. When the first parameter identification
number is reached, the next DEC key press will cause the last parameter ID
number to be displayed.
For example: If the controller’s label lists 34 parameters, then pressing the
DEC key when the display is blinking the value 01 will cause the display
to wrap around to the last parameter listed, which in this case is 34, and
blink this new value.
In PARAMETER EDIT MODE, each DEC key press will decrease a parameter’s
current value. If the DEC key is held down while in PARAMETER EDIT MODE the
value will automatically continue to be decreased at gradually faster and faster
rates until the DEC key is released or the parameter’s minimum allowed value is
reached. When the lower two digits display a 00, pressing the DEC (decrease
key) will cause the lower two digits to display a 99 and the hundreds digit will have
been decreased by 1.
INC and DEC Keys Together

In PARAMETER EDIT MODE, the INC and DEC keys are used together to view
the value of the upper two digits of a 4-digit number.
Press and hold both INC and DEC simultaneously to view the value of a
4-digit number’s upper two digits. Note that the left digit’s decimal point is
turned on to indicate that the thousands and the hundreds digits are being
displayed.
Release INC and DEC and now the tens and the ones digits are again
being displayed. Note that the right digit’s decimal point is blinking if
editing is allowed or just ON if editing is not allowed.
Note: Not all parameters are 4-digit numbers, in which case the upper digits will
always display 0.0 (zero dot zero).
In PARAMETER SELECT MODE, pressing both the INC and DEC keys at the
same time will cause all LED segments to be turned on. This serves as an LED
test. Release the keys to resume displaying the parameter ID number.
Woodward 5
LED Display
The two 7-segment LED’s along with each digit’s corresponding decimal point are
used to display values and indicate the operating mode of the user interface.
When the value being displayed by the two 7-segment LEDs is blinking,
PARAMETER SELECT MODE is active.
When the value displayed is not blinking, the selected parameter’s value is being
displayed and the user interface is in PARAMETER EDIT MODE. The decimal
points further indicate which half of a 4-digit value is being displayed and whether
editing is allowed.
The right digit’s decimal point is used to indicate that the lower 2 digits of a value
(the tens and the ones digits) are being displayed. When the right decimal point is
blinking, it means that the value can be modified using the INC key or the DEC
key. No blinking means that editing is not allowed or is password protected.
The left digit’s decimal point is used to indicate that the upper 2 digits of a value
(the thousands and the hundreds digits) are being displayed. The upper 2 digits
are always view only so the right decimal point does not blink. Changes to the
upper digits occur when a parameter’s lower digits overflow or underflow during
editing.
An overflow occurs when the value 99 is displayed and the INC key is pressed
(assuming this is not the parameter’s maximum value). This will cause the
displayed value to become 00 while the non-displayed value in the parameter’s
upper 2 digits will be increased by one. You can verify this by pressing both INC
and DEC at the same time to view the new value in the upper digits. For example:
If the full 4-digit value of the parameter you are editing is currently 1099, then after
pressing the INC key the parameter’s new value will be 1100.
Woodward 6
An underflow occurs when the value 00 is displayed and the DEC key is pressed
(assuming this is not the parameter’s minimum value). This will cause the
displayed value to become 99 while the non-displayed value in the parameter’s
upper 2 digits will be decreased by one. You can verify this by pressing both INC
and DEC at the same time to view the new value in the upper digits. For example:
If the full 4-digit value of the parameter you are editing is currently 1800, then after
pressing the DEC key the parameter’s new value will be 1799.
When values exceeding 9,999 are to Decimal to Hexadecimal

be displayed, the controller uses the Conversion Chart
hexadecimal numbering system to Decimal Hexadecimal
Value Equivalent
represent the value of the thousands
10 A
position.
11 B
12 C
Example 1: The desired set speed is 13 D
10,069 Hertz. The upper two digits 14 E
displayed by the controller will be 15 F
[A.0], and the lower 2 digits displayed
will be [69.].
Example 2: The desired set speed is 10,972 Hertz. The upper two digits displayed
by the controller will be [A.9] and the lower 2 digits displayed will be [72.].
Woodward 7
Chapter 3.
Parameter Reference
This chapter provides information regarding each parameter’s function. Each of

this chapter’s subsections provides information about a single parameter.
Subsection numbering corresponds to the parameter numbering on the governor’s

label to make it easier to locate information about the parameter of interest. For
example: Parameter 5. PROPORTIONAL is described in subsection 3.5 (chapter
3 subsection 5).
The following table lists each of the parameters and their default, minimum, and
maximum values. Note that several of the parameters have minimum and
maximum values set by other parameters. Parameters listed in boldface are
required settings for the controller.
Note also that all Speed and Rate values are shown as magnetic pick-up Hertz
values (parameters 2-4, 14-16, 26-31, 33). Changing the No. of Flywheel Teeth
will cause different default values to be displayed based on the Hertz to RPM
formula described in subsection 3.1 below.
Woodward 8
DPG-2201-00X Parameter List

PARAMETER NAME DEFAULT MINIMUM MAXIMUM
1. No. Of Flywheel Teeth 0 0 572
Set Speed A Set Speed A
2. Set Speed A 1000
Min Max
Set Speed B Set Speed B
3. Set Speed B 1000
Min Max
Idle Speed Idle Speed
4. Idle Speed 500
Min Max
5. Proportional 25 1 99
6. Integral 50 0 99
7. Derivative 25 0 99
8. OVG @ Set Speed A 20 1 99
9. OVG @ Set Speed B 20 1 99
10. OVG @ Idle Speed 20 1 99
11. Gain Factor 20 1 99
12. Speed Filter 16 1 24
13. Idle Hold Time 0 0 9999
14. Accel Rate 1000 1 11000
15. Decel Rate 1000 1 11000
16. Startup Rate 1000 1 11000
17. Startup Limit 1000 0 1000
18. Torque Limit 1000 0 1000
Integral High
19. Integral Low Limit 0 0
Limit
Integral Low
20. Integral High Limit 99 99
Limit
21. % Droop 0 0 100
22. No Load Cal 0 0 1000
23. Full Load Cal 1000 0 1000
24. Password 0 0 99
-001 100 0 100
25. Over Speed Limit
-002 15000 0 15000
26. Set Speed A Min 10 10 Set Speed A
27. Set Speed A Max 11000 Set Speed A 11000
28. Set Speed B Min 10 10 Set Speed A
29. Set Speed B Max 11000 Set Speed B 11000
30. Idle Speed Min 10 10 Idle Speed
31. Idle Speed Max 11000 Idle Speed 11000
32. Duty Cycle Limit 95 10 95
33. Startup Speed 1000 10 11000
34. Startup Duty Cycle 30 5 95
Parameters 2, 5, 6, 7, 8, 11 and 12 require adjustment, while adjustments to
the other parameters are optional.
Woodward 9
3.1 No. of Flywheel Teeth (optional)

This parameter provides the conversion factor needed by the governor to display
speeds as RPM values instead of Hertz values. Adjusting this parameter is
optional. To use this parameter correctly, you must know the exact number of
flywheel teeth that pass by the magnetic pickup in one revolution of the engine.
The default value of 0 disables Hz to RPM conversions so all set speeds are
displayed in MPU (magnetic pick-up) Hertz. Setting this parameter to a value
other than zero enables Hz to RPM conversion.
Adjust this parameter to a value equal to the exact number of pulses that the MPU
delivers to the governor in one revolution of the engine to display set speeds in
RPM. The formula used to convert the magnetic pickup signal from a Hertz value
to a RPM value is:
[(MpuHertz ) × (60s )] = [EngineRPM ]

[NumberOfTeeth]
For example:
[(3960 Hz ) × (60s )] = [1800 RPM ]

[132Teeth]
The following derivation of the above formula can be used to convert from RPM to
Hertz.
[(EngineRPM ) × (NumberOfTeeth )] = [MpuHertz ]

[60s ]
3.2 Set Speed A (required)

SET SPEED A is the governor’s target speed when the SPEED SEL input
(terminal 8) is open and the startup sequence has completed. The startup
sequence is complete when the target speed and the engine speed reach the set
speed.
When a two-position switch is connected between SPEED SEL and +5 Vdc

(terminal 13), then an open switch selects SET SPEED A as the governor’s target
speed. If the governor’s SPEED SEL input is not used, then SET SPEED A is
automatically the active target speed after the startup sequence is completed.
The default value for SET SPEED A is 1000 MPU Hertz. The SET SPEED A
parameters adjustable range extends from SET SPEED A MIN to SET SPEED
A MAX.
When SET SPEED A values greater than 9999 are displayed, the left most digit
uses the capital letter A to represent 10000 and the lower case letter b to
represent 11000.
Woodward 10
For example: If SET SPEED A is set to 10750, then the upper 2 digits will be
displayed by the controller as [A.7] and the lower 2 digits will display [50].
3.3 Set Speed B (optional)

SET SPEED B becomes the governor’s target speed when the SPEED SEL input
(terminal 8) is at +5 Vdc (terminal 13) and the startup sequence is complete. The
startup sequence is complete when the target speed and the engine speed reach
the set speed.
When a two-position switch is connected between SPEED SEL and +5 Vdc, then
a closed switch selects SET SPEED B as the governor’s target speed.
If the governor’s SPEED SEL input is not used, then SET SPEED A is
automatically the active target speed after the startup sequence is completed.
The default value for SET SPEED B is 1000 MPU Hertz. The SET SPEED B
parameters adjustable range extends from SET SPEED B MIN to SET SPEED
B MAX.
When SET SPEED B values greater than 9999 are displayed, the left most digit
represent 11000.
For example: If SET SPEED B is set to 11000, then the upper 2 digits will be
displayed by the controller as [b.0] and the lower 2 digits will display [00].
3.4 Idle Speed (optional)

IDLE SPEED is the governor’s target speed for the IDLE HOLD TIME (parameter
13) when the engine is started. When the idle hold timer reaches zero, the target
speed will become either SET SPEED A or SET SPEED B depending on the state
of the SPEED SEL input terminal.
The default value for IDLE SPEED is 500 MPU Hertz. The IDLE SPEED
parameters adjustable range extends from IDLE SPEED MIN to IDLE SPEED
MAX.
When IDLE SPEED values greater than 9999 are displayed, the left most digit
represent 11000.
For example: If IDLE SPEED is set to 11000, then the upper 2 digits will be
displayed by the controller as [b.0] and the lower 2 digits will display [00].
NOTE—When the No. of Flywheel Teeth parameter is used, the SET

SPEED A, SET SPEED B, and IDLE SPEED parameters are displayed
as RPM values instead of Hertz values.
Woodward 11
3.5 Proportional (required)

The proportional term is one of the interrelated PID terms that determine how well
a DPG-2201-00X controller governs the engine’s speed. A speed change creates
a speed error (the difference between the target speed and the actual speed.) The
proportional gain controls the size of the governor output response to a step
change in the speed error.
Saturation
100% a higher Proportional value
Increases output response to a step
change in error
Controller output (%)

a lower Proportional value
Decreases output response to a step
Change in error
50%
Proportional
response
Saturation
0%
Error (%)
(-) 0 (+)
Each error value produces a unique controller output value
3.6 Integral (required)

The integral term is one of the interrelated PID terms that determine how well a
DPG-2201-00X controller governs the engine’s speed. The integral term acts to
drive speed error to zero. In a proportional only control with constant load, there will
be a constant speed error that inversely relates to the proportional gain of the
system. The integral term is key to isochronous speed control. This term eliminates
the difference between the programmed set speed and the actual speed. The
integral gain changes the time it takes to drive the error to zero.
Note: Integral is needed to eliminate speed offsets due to proportional gain and
should never be left at zero.
Integral response to constant error

100%
larger
Integral
value
smaller
50% Integral
value
0% Time
Error
Time
Woodward 12
3.7 Derivative (required)

The derivative term is one of the interrelated PID terms that determine how well a
DPG-2201-00X controller governs the engine’s speed. The derivative responds to
the rate of change in the speed error. This parameter is primarily used to dampen
very rapid oscillations resulting from large speed changes. The derivative
responds to engine acceleration or deceleration. If the engine speed approaches
the target speed at a fast rate, the derivative acts to minimize or eliminate
overshoot. A zero value is allowed but systems typically require some derivative
gain to improve overall engine speed control.
Derivative response to changes

100% in the rate of deceleration or the

rate of acceleration.
50%
0% Time
(+)
Error
0 Time
(-)
The error is sampled at regular intervals
When the "Rate of change" changes (red dot) the

Derivative's impact on controller output changes.
3.8 OVG @ Set Speed A (required)

This overall gain acts as the multiplier on the three PID terms (proportional,
integral, and derivative) when Set Speed A is selected as the active target speed.
This gain term is adjustable from 01 to 99.
3.9 OVG @ Set Speed B (optional)

integral and derivative) when Set Speed B is selected as the active target speed.
This gain term is adjustable from 01 to 99.
3.10 OVG @ Idle Speed (optional)

integral, derivative) when the Idle Speed is the active target speed. The idle speed
set point is active only during startup when the idle hold timer is running. This gain
term is adjustable from 01 to 99.
3.11 Gain Factor (required)

The gain factor parameter is used to obtain more range of adjustment from the
PID terms. In other words, if any of the PID terms or the overall gain terms reach
their adjustment limits then this value can be modified to provide for more range of
adjustment in the PID and OVG terms.
Woodward 13
For example, if the PID terms are set to 90, 80, and 50 respectively and the Gain
Factor is set to 20, then doubling the Gain Factor by setting it to 40 allows the PID
terms to be halved to 45, 40, and 25 respectively. These new settings are
equivalent to the previous settings with respect to the governor’s tuning response
and now allow the PID terms to be adjusted higher if needed.
3.12 Speed Filter (required)

This parameter indicates the number of flywheel teeth to use when computing an
average engine speed and is used to dampen out speed measurement variations
that can make PID tuning difficult. But, keep in mind the following.
• Too much filtering will slow down the governor’s response
to speed changes.
• Too little filtering can make the governor overly sensitive
and tuning difficult.
There is measurable acceleration and deceleration that occurs between cylinder

firings. As a general rule, less filtering is required the more engine cylinders there
are. This is because the number of acceleration-deceleration cycles increases and
these oscillations will have lower amplitude. With more cylinders, there is less time
for the speed to slow down before the next cylinder firing.
Rotational mass also affects the amount of speed signal filtering needed. The
more rotational mass, the less filtering is needed. The less rotational mass, the
more filtering is needed.
Typically, the value 24 works well on small 3- or 4-cylinder engines. A value of 16

is recommended for 6- or 8-cylinder engines. The following formula can also be
used to derive a good starting point for the speed filter value for a given engine
application. Round the result to the nearest integer. The maximum value allowed
is 24.
[(No._of_flywheel_teeth) / (No._of_engine_cylinders)] * 0.75 = speed_filter_value
3.13 Idle Hold Time (optional)

The idle hold time specifies how long, after starting, the engine is to stay at the
idle speed before finishing the ramp to the target speed. The time value has a
resolution of one-tenth of a second.
During the startup sequence, the governor increases the engine speed from the
engine’s crank speed to the active target speed at the STARTUP RATE specified.
If the IDLE HOLD TIME is nonzero, the initial target speed will be the IDLE
SPEED. After the IDLE HOLD TIME expires the governor then uses the
STARTUP RATE to ramp the engine to the selected set speed (SET SPEED A or
SET SPEED B). The startup sequence is complete once the engine speed
reaches the selected set speed.
3.14 Accel Rate (optional)

This rate specifies how fast the governor should increase the engine’s speed
when a new higher target speed is made active. The parameter value is specified
in MPU (magnetic pickup) Hz per second based on the following formula.
[(higher_speed_in_Hertz) – (lower_speed_in_Hertz)] / (ramp_time_in_seconds) =

accel_rate_value
Woodward 14
For example, suppose Set Speed A is 3300 Hertz and Set Speed B is at 3960
Hertz. The governor is currently controlling the engine at 3300 Hertz (Set Speed
A), when Set Speed B becomes the active target speed. It is desired that the new
speed of 3960 be reached in precisely 2 seconds. The following formula
determines the value needed by Accel Rate to increase the engine speed from
Set Speed A to Set Speed B in 2 seconds.
[(Set Speed B) – (Set Speed A)] / (N seconds) = accel_rate_value in Hertz per

second
[3960 – 3300] / 2 = 330 Hertz per second
3.15 Decel Rate (optional)

The Decel Rate specifies how fast the governor should decrease the engine’s
speed when a new lower target speed is made active. The parameter value is
specified in MPU (magnetic pickup) Hertz per second based on the following
formula.
[(higher_speed_in_Hertz) – (lower_speed_in_Hertz)] / (ramp_time_in_seconds) =

decel_rate_value
For example, suppose Set Speed A is 4170 Hertz and Set Speed B is 3475 Hertz.
The governor is currently controlling the engine at 4170 Hertz (Set Speed A),
when Set Speed B becomes the active target speed. It is desired that the new
speed of 3475 be reached in precisely 1.5 seconds. The following formula
determines the value needed by Decel Rate to decrease the engine speed from
Set Speed A to Set Speed B in 1.5 seconds.
[(Set Speed A) – (Set Speed B)] / (N seconds) = decel_rate_value in Hertz per

second
[4170 – 3475] / 1.5 = 463 Hertz per second
3.16 Startup Rate (optional)

This parameter is used to achieve a smooth controlled engine start. On diesel
engines, this feature is also useful for minimizing exhaust smoke at startup. When
used in combination with the Idle Speed and Idle Hold Time, a brief warm-up cycle
can be programmed.
The startup rate specifies how fast the governor should increase the engine speed
when the engine is started. The rate value indicates Hertz per second. The
formula to use for determining a precise Startup Rate is shown below.
[(final_target_speed_in_Hertz) – (crank_speed_in_Hertz)] /
(ramp_time_in_seconds) = startup_rate_value
The governor increases the engine speed from the engine’s crank speed to the
active target speed at the rate specified. The governor will bring the engine to the
Idle Speed for the Idle Hold Time then continue increasing the engine speed at
this same ramp rate until the engine reaches the selected target speed (Set
Speed A or Set Speed B).
Exception 1: In cases where the target speed is less then the

Idle Speed and the Idle Hold Time is nonzero, the startup
ramp sequence ends when the Idle Speed is reached. Then
the Decel Rate is used to ramp the engine speed down to the
target speed from the Idle Speed.
Woodward 15
The ramp up will pause at the STARTUP SPEED until the governor senses an
MPU signal greater than the STARTUP SPEED. This prevents the startup ramp
from reaching completion before the engine has even started. The governor
considers MPU frequencies below the STARTUP SPEED as indicating that the
engine is cranking but has not yet started. MPU frequencies above the STARTUP
SPEED are taken to indicate that the engine has started and the governor will
increase the engine speed until the selected set speed is reached.
Exception 2: In cases where the target speed is less the

STARTUP SPEED, the startup ramp sequence ends when
the target speed is reached.
During the startup sequence, the governor increases the engine speed from the
engine’s crank speed to the active target speed at the STARTUP RATE specified.
If the IDLE HOLD TIME is nonzero, the initial target speed will be the IDLE
SPEED. After the IDLE HOLD TIME the governor then uses the STARTUP RATE
to ramp the engine to the selected set speed (SET SPEED A or SET SPEED B).
The startup sequence is complete once the engine speed reaches the selected
set speed.
NOTE—When the No. of Flywheel Teeth parameter is used, the ACCEL

RATE, DECEL RATE, and STARTUP RATE parameters are displayed
as a RPM quantity per second instead of Hz/sec values. The given rate
formulas can be used to compute rates in terms of RPM values by
substituting the Hertz speed values with RPM speed values
3.17 Startup Limit (optional)

The startup limit parameter is used to limit the fuel supplied to the engine during
startup. The default value of 1000 allows the actuator drive signal to use 100.0%
of available current. Decreasing the value limits the available drive signal thereby
limiting how far open the actuator can go. Increasing the value allows the actuator
to open further.
The value assigned to the startup limit parameter is in units of one-tenth of a

percent of the actuator’s maximum current feedback reading. The governor
measures actuator drive-signal feedback and obtains an approximation of the
amperes of current flowing through the actuator. Fuel limiting is achieved by
setting the maximum level of electrical current allowed to flow through the actuator
during engine startup. This feature is useful in reducing smoke when starting
diesel engines.
NOTE: If the value is set too low the engine may not start.
3.18 Torque Limit (optional)

The torque limit parameter is used to limit the fuel supplied to the engine during
heavy generator loads or generator overloads. The default value of 1000 allows
the actuator drive signal to use 100.0% of available current. Decreasing the value
limits the available drive signal thereby limiting how far open the actuator can go.
Increasing the value allows the actuator to open further.
The value assigned to the torque limit parameter is in units of one-tenth of a

percent of the actuator’s maximum current feedback reading. The governor
measures actuator drive-signal feedback and obtains an approximation of the
amperes of current flowing through the actuator. Fuel limiting is achieved by
Woodward 16
setting the maximum level of electrical current allowed to flow through the actuator
during normal operation.
NOTE: If the value is set too low the engine will not be able to carry its rated load.
3.19 Integral Low Limit (optional)

The integral low limit prevents "integral windup" in the negative direction. In other
words, the integral low limit parameter is used to reduce under speed duration
after a long or sustained over speed condition was present. The low limit helps
reduce the duration and amount of engine under speed by maintaining a minimum
actuator position.
When smaller PWM duty cycle values do not reduce the engine speed any further
but an off speed (measured speed greater than the target speed) remains, letting
the Integral term grow more negative is not beneficial. Unused negative
integration would cause a slower recovery from an under speed condition.
The integral low limit specifies the PWM duty cycle where the integrator’s
influence on lowering PID output must stop. The default value is 0%. The value
can be adjusted from 0% to 90% in 1% increments.
CAUTION—Use carefully, as improper use can prevent the governor

from ever reaching the target speed. The first line of defense in
reducing overspeed or under speed errors is a well-tuned governor
via the PID terms.
3.20 Integral High Limit (optional)

The integral high limit prevents "integral windup" in the positive direction. In other
words, the integral high limit parameter is used to reduce over speed duration
after a long or sustained under speed condition was present. The high limit helps
reduce the duration and amount of engine over speed by maintaining a maximum
actuator position.
When larger PWM duty cycle values do not increase the engine speed any further
but a negative off speed (measured speed less than the target speed) remains,
letting the Integral term grow more positive is not beneficial. Unused positive
integration would cause a slower recovery from an over speed condition.
If an engine overload situation causes the engine speed to remain below the
target speed for some period of time, then the integral portion of PID output would
grow larger than otherwise needed (would windup). Therefore, when the load is
removed the engine may over speed because it takes time for the integral portion
of PID output to shrink or “unwind.” This is where reducing the Integral Limit High
value can help by preventing excessive windup in the PID output’s integration
term.
The integral high limit specifies the PWM duty cycle where the integrator’s
influence on raising PID output must stop. The default value is 99%. The value
can be adjusted from 99% down to 10% in 1% increments.
CAUTION—Use carefully, as improper use can prevent the governor

from ever reaching the target speed. The first line of defense in
reducing overspeed or under speed errors is a well-tuned governor via
the PID terms.
Woodward 17
3.21 Percent Droop (optional)

The percent droop parameter is used to select droop mode operation and specify
the percentage of droop required. When the percent droop parameter is set to
zero (the default setting) then droop mode is not active. Droop mode is active
when this parameter is set to any value from 1 to 100, which corresponds to 0.1%
to 10.0% droop.
The following formula determines the no load droop speed.
[(selected_set_speed) / ((1000 – value_of_%_DROOP) / 1000)] =

no_load_droop_speed
For example: If 5% droop is desired, set the percent droop value to 50. Now if the
selected set speed is 1800 RPM then the no load droop speed will be:
[(1800 RPM) / ((1000 – 50) / 1000)] = 1800 RPM / 0.95 = 1895 RPM
NOTE: This parameter can only be modified during the Droop Calibration
Procedure. See the Calibration Instructions chapter for more information.
Droop mode relies on knowing the actuator position. The actuator’s position
corresponds to the amount of fuel being delivered to the engine. The DPG-2201-
00X controller senses electrical current flow through the actuator to determine its
position. This method of position sensing does not work with all actuators.
3.22 No Load Calibration (optional)

The No Load Calibration value is learned during the Droop Calibration Procedure
and should not be set manually. Once calibrated, the no load calibration value
indicates the percentage of electrical current, relative to the measurable
maximum, that must flow through the actuator to run the engine at the no load
droop speed.
The factory default value is zero, so if droop mode is to be used, this parameter
must be calibrated. The no load calibration value must be less than the full load
calibration value for proper droop operation. If after performing the Droop
Calibration Procedure the no load calibration value is greater than the full load
calibration then the droop function cannot be used. Some actuators may have a
current versus position curve that is incompatible with this controller’s method of
determining actuator position.
NOTE: This parameter is only modified during the Droop Calibration

3.23 Full Load Calibration (optional)

The Full Load Calibration value is learned during the droop calibration procedure
and should not be set manually. Once calibrated, the full load calibration value
indicates the percentage of electrical current, relative to the measurable
maximum, that must flow through the actuator to run the engine at the selected
set speed when a full load is being applied to the generator.
The factory default value is 1000, so if droop mode is to be used, this parameter
must be calibrated. The full load calibration value must be greater than the no load
calibration value for proper droop operation. If after performing the Droop
Calibration Procedure the full load calibration value is less than the no load
calibration value then the droop function cannot be used. Some actuators may
Woodward 18
have a current versus position curve that is incompatible with this controller’s
method of determining actuator position.
NOTE: This parameter is only modified during the Droop Calibration

3.24 Password (optional)

The password parameter is provided to protect against inadvertent parameter
changes that may occur whenever the keys are pressed and a parameter
modification is not intended. The password parameter has three possible settings:
DISABLED, LOCKED, and UNLOCKED
DISABLED–This setting turns off any password protection. Use this setting if
password protection is not desired. This is the default setting as shipped from the
factory. Entering a value of [99] sets the password protect parameter to the
disabled mode. When the password protect parameter is selected, the LED
display will show [Pd] for 2 seconds, indicating the password-disabled mode, then
the value [00.] is displayed. The user can then edit the value.
LOCKED–This setting means that password protection is active and only

parameter viewing is allowed (parameter editing is disabled). Enter a value of [22]
to set password protect to locked mode. For 2 seconds after selection of the
password protect parameter, the LED display will show [PE.] for this mode and the
rightmost decimal point will be ON (not blinking), then the value [00.] is displayed.
The user can then edit the value.
UNLOCKED–This setting means that password protection is active but parameter

editing is allowed. Entering a value of [30] while in LOCKED mode will UNLOCK
parameter editing. The user is free to edit parameters. If there is no keypad
activity for 5 minutes, the controller returns to LOCKED mode. If not already in the
UNLOCKED mode, the user must get into the UNLOCKED mode in order to enter
a 99 to disable password protection.
3.25 Over Speed Limit (optional)

DPG-2201-001
This parameter is used to determine the engine speed that will trigger the
governor to output minimum fuel. The parameter’s value is in terms of a
percentage over the highest set speed. In other words, an over speed condition is
detected if the engine speed reaches a speed of [OVER SPEED LIMIT %] greater
than the highest set speed.
For example: If the highest set speed is 1800 RPM and this parameter is set to
20, then an over speed condition will be detected at 2160 RPM (the value that is
20% greater than 1800). Formula: 1.20 * 1800 RPM = 2160 RPM
The default value of 100 is used to disable over speed detection. Use values less
than 100 to enable the over speed limit function and set the limit speed to [(1 +
(overspeed_limit_value/100)) * (highest_set_speed)].
DPG-2201-002
This parameter is used to determine the engine speed that will trigger the
governor to output minimum fuel. The parameter’s value is set as a frequency in
Hertz or as an RPM value depending on whether the No. of Flywheel Teeth
parameter is zero or nonzero respectively. The default value of 15,000 Hertz is
used to disable over speed detection.
Woodward 19
The governor detects an over speed condition when it measures an engine speed
that exceeds the OVER SPEED LIMIT value. When an over speed is detected the
governor’s actuator output signal is set to minimum.
NOTE for DPG-2201-002 Models:

When the No. of Flywheel Teeth parameter is used, the OVER SPEED LIMIT
parameter is displayed in RPM values instead of Hertz values.
NOTE— The governor must be turned off to clear the over speed
detection before the engine can be restarted.
3.26 Set Speed A Min (optional)

Set Speed A Min is used to set the lowest value allowed for adjustments of Set
Speed A. This parameter can be set to any value within the range bordered by 10
Hertz (or its RPM equivalent) and the current value of Set Speed A.
3.27 Set Speed A Max (optional)

Set Speed A Max is used to set the highest value allowed for adjustments of Set
Speed A. This parameter can be set to any value within the range bordered by
current Set Speed A setting and 11,000 Hertz (or its RPM equivalent).
3.28 Set Speed B Min (optional)

Set Speed B Min is used to set the lowest value allowed for adjustments of Set
Speed B. This parameter can be set to any value within the range bordered by 10
Hertz (or its RPM equivalent) and the current value of Set Speed B.
3.29 Set Speed B Max (optional)

Set Speed B Max is used to set the highest value allowed for adjustments of Set
Speed B. This parameter can be set to any value within the range bordered by
current Set Speed B setting and 11,000 Hertz (or its RPM equivalent).
3.30 Idle Speed Min (optional)

Idle Speed Min is used to set the lowest value allowed for adjustments of Idle
Speed. This parameter can be set to any value within the range of 10 Hertz (or its
RPM equivalent) and the current value of Idle Speed.
3.31 Idle Speed Max (optional)

Idle Speed Max is used to set the highest value allowed for adjustments of Idle
Speed. This parameter can be set to any value within the range bordered by
current Idle Speed and 11,000 Hertz (or its RPM equivalent).
3.32 Duty Cycle Limit (optional)

The duty cycle limit parameter sets the absolute maximum amount of drive signal
that can be output to the actuator and thus serves as a mechanism for fuel
limiting. Fuel limiting is achieved by setting the maximum duty cycle or ontime
Woodward 20
allowed during one cycle of the PWM (pulse-width-modulation) signal controlling
the actuator drive circuit. The value assigned to the duty cycle limit parameter is a
percentage, and is limited to values in the range 10% to 95%. The default value is
95%.
3.33 Startup Speed (optional)

May be required on slow cranking engines.
The startup speed parameter should be set to an engine speed at least 10%
higher than the fastest engine cranking speed but lower than the engine’s idle
speed. This allows the governor to determine whether the engine is cranking or
running whenever an engine speed signal is present.
If the Startup Speed value is set too low (less than crank speed) the governor’s
target speed will be ramped to the active set speed (Idle Speed, Set Speed A, or
Set Speed B) before the engine has started. Therefore, when the engine does
start, it may over speed or output excessive smoke because the startup ramp,
having already completed, no longer controls the rate of engine speed increase.
If the Startup Speed value is set too high (above the active set speed) then the
Startup Speed becomes the target speed that the governor must reach before the
governor considers the startup sequence complete. Typically, the startup
sequence ends when the engine speed reaches the active set speed. The active
set speed is the Idle Speed if the Idle Hold Time parameter is a nonzero value or
the “selected set speed” (either Set Speed A or Set Speed B).
To determine the proper value for this parameter the crank speed must be known.
There are two ways to determine the engine crank speed.
1) Use a meter to measure the frequency across the MPU+ and
MPU- terminals of the governor during cranking or . . .
2) Use a PC running the Universal PST application and read the
value of the Measured Speed in the View Status panel when
the engine is cranking. Note: From the Universal PST’s startup
screen press the View Status button, then press the Start
Monitoring button to begin reading values.
3.34 Startup Duty Cycle (optional)

The startup duty cycle parameter is used to pre-load the PID output with a PWM
duty cycle value close to that needed for the actuator to allow enough fuel to idle
the engine.
If the value is too low, then the engine crank time may be longer than desired
because the governor’s actuator output starts from a value much smaller than
needed to begin opening the fuel valve.
If the value is too high, then the engine may over speed because the actuator
opens more than needed to start the engine.
There are two ways to determine a good value to use for this parameter.
1) Use a meter to measure the duty cycle across the ACT
terminals of the governor while the engine is running. Note:
To determine if your meter is reading the correct value:
a. First, apply power to the governor but do NOT
start the engine
b. Second, measure the duty cycle across the
ACT terminals (#3 and #4). The reading should
Woodward 21
be 5 for 5%. If the reading is 95, then reverse
the leads.
2) Use a PC running the Universal PST application and read the
value of the PWM command in the View Status panel when
the engine is cranking. Note: from the Universal PST’s
startup screen press the View Status button, then press the
Start Monitoring button to begin reading values.
Woodward 22
Chapter 4.
Universal PST
Introduction
The Universal Parameter Setup Tool (Universal PST) is a Microsoft® Windows®
application available from Woodward that enables you to adjust governor
parameter settings and monitor governor operation. Universal PST also includes a
graphical chart recorder that displays engine speed in real-time. This provides a
visual representation of how the engine speed changes in response to changes in
load, which can be very helpful when tuning the governor.
This chapter provides the information needed to use a computer with your
governor. Here you will find instructions for acquiring, installing, and running the
Universal PST on your PC. Also described is information for obtaining or
constructing the communications cable needed to connect the governor’s COMM
port to your computer’s serial port during service and initial programming.
Features
Universal PST features include:
• Automatic configuration to each DPG when communications are
established
• Read/write access to all DPG programmable parameters and features
• View each parameter's default, minimum, and maximum values
• Diagnostics utilizing automatic refresh of DPG status
• Save and open DPG setup data information to and from a file for reuse
• Single button read to get the current values of all parameters
• Single button write to program a DPG with previously saved setup
values
• Engine speed monitoring via a chart recorder to aid in tuning the
governor
• Saving chart recorder data to a Microsoft Excel compatible file
• Help information on each of the governor’s parameters
• Help information on using the Universal PST
System Requirements
Universal PST minimum system requirements:
• Pentium® 133 MHz PC
• 50 MB of hard disk space
• 64 MB of RAM
• Display resolution set to SVGA (800x600) or higher
• Windows® 98se, NT 4.0, 2000, and XP or greater
• Windows® 95 or ME not supported
Woodward 23
Acquiring Universal PST

There are two ways to acquire a copy of the Universal PST application:
• Obtain the DPG Software Calibration Kit
• Download the application from the Woodward website
Obtaining the DPG Software Calibration Kit:

The DPG Software Calibration Kit (Woodward P/N 8447-1003) contains the
latest version of Universal PST on CD-ROM, a DB-9 Modular Adapter and
modular cable. Contact the Woodward sales department to request a DPG
Software Calibration Kit for a nominal charge. Telephone: (847) 967-7730.
Downloading Universal PST:

The Universal PST application is also available to download from the
Woodward Software Products page at www.woodward.com/IC/Software, Use
the “Select a Product” drop down menu in the center of the web page to select
“DPG-2xxx digital governors” then press the [Go] button.
This will automatically redirect you to the Universal PST download page
where you can click on the word Download to begin the download process.
Once you are logged into the Woodward download site you are presented
with the File Download dialog box shown below, or one similar. Click the
[Save] button and choose a folder to save the download to.
NOTE: Due to the large file size, it is recommended that the [Open] button not
be used because this would try to run the self-extracting executable from the
web site.
Woodward 24
Installing Universal PST

Instructions to Install from CD-ROM:
When you insert the DPG Software Calibration Kit’s CD-ROM into your
computer, the “autorun” file on the CD will attempt to launch the “setup.exe”
program. If the “autorun” feature is disabled on your computer or does not
start the setup program you can launch the program manually. To start the
installation manually, explore the contents of the CD then double click on the
“setup.exe” file.
Instructions to Install from the Downloaded File:

The file downloaded from the Woodward web site contains two files:
“ReadMeFirst.txt” and “setup.exe”. Run the downloaded file to extract its
contents to a folder you choose on your computer’s hard drive. Then run the
“setup.exe” program from the folder you extracted it to.
IMPORTANT:
The installation program will detect operating system components older than
those required by the "Universal PST" application. In this case the installation
program will ask if you want to update Windows. If you do not want "setup" to
update your system then you can not use the "Universal PST" application on
this computer.
Read the setup program's instructions carefully as they appear and respond
as needed. The installation may take as long as 7 minutes depending on your
computer's power and operating system. Do not interrupt the installation
program even though it may appear as
though it is not running.
NOTE: Administrator rights may be needed to install on some Microsoft

Windows operating systems (such as Windows XP Professional) for the setup
program to properly register application resources.
Wiring the COMM Port to a PC

To construct a communications cable to use between the DPG’s COMM port
and your PC’s RS-232 serial port refer to the table and wiring diagram below.
RJ11 OR
RJ12 RJ11M
DPG-22XX SIGNAL CONNECTS TO:
POSITION 654321
1 No connection N/C
PC receive (RxD)
2 Transmit data to PC
DB9 pin 2
PC transmit (TxD)
3 Receive data from PC
DB9 pin 3
5 4 3 2 1
PC common
4 COMMON
DB9 pin 5
5 +5 Vdc (Do NOT 9 8 7 6

N/C
connect at the PC end) DB9F
6 No connection N/C
NOTE—Remote access via the COMM port is intended for connection

only while programming, tuning and troubleshooting the control/
engine. It is a service port and not intended for permanent connection
of a PC and/or cable
Woodward 25
Communications Error
The following message window appears when Universal PST is running and
unable to communicate with a DPG.
After the problem is found and corrected, you can either restart Universal PST
or press the <Read All> button to clear the error message. The <Read All>
button is near the lower left corner of Universal PST’s main startup screen.
Universal PST User Interface Overview

Universal PST has two main display modes.
• Table View (the main startup screen)
• Chart View
TABLE VIEW
In Table View the user can:

• View the current values for all user programmable parameters in the
Parameter Setup panel.
• Edit a parameter’s value by double-clicking on a cell in the “Value”
column of the table.
• Press the <Read All> button to refresh the values displayed in the
Parameter Setup panel.
• Press the <Write All> button to transmit setup values to the governor.
• Press the <View Status> button to display read only parameters in the
Status View panel.
Woodward 26
• Press the <View Chart> button to set the display mode to Chart View.
• Select items from the menu.
CHART VIEW
In Chart View the user can:

• Monitor engine speed in real-time.
• Adjust the horizontal and vertical scale settings of the chart recorder.
• Edit parameter values related to governor tuning. These same
• parameters are also on the main parameter setup table.
• Press the <Data File => button to open a file for saving chart recorder
data.
• Press the <Data Reset> button to start data collection to the open file
at the beginning.
• Press the <Pause Chart> button to stop the chart recorder, which also
stops writing data to the file. Press the <Continue> button to turn the
chart recorder back on.
• Press the <View Table> button to set the display mode back to Table
View.
• Select items from the menu.
NOTE: Pressing a button means positioning the mouse pointer over the
button and clicking the left mouse button.
Woodward 27
Universal PST Menu Items

Use the File menu to:
• Open a previously saved setup data file
• Save setup data to a file
• Send setup data to the default printer
• Exit the program
Use the View menu to:

• Select Parameter Table view (Table
View)
• Select Chart Recorder view (Chart
View)
Use the Port menu to:

• Select the PC’s serial port that is
connected to the DPG-2000
Use the Help menu to access:

• Help on the Universal PST for DPG
• Help on the DPG-2000 product that is
currently in communication with the PC
• Information about the Universal PST for
DPG application
Parameter Setup
The Parameter Setup panel displays a table where each row shows the Name
of a user programmable parameter, its current Value, and the parameter’s
Default, Minimum, and Maximum values.
To modify a parameter’s current value, it must first be selected. Do this by

double-clicking the left mouse button on a cell in the table that is at the
intersection of the parameter’s row and the Value column. The selected cell
will be highlighted and the value can now be modified. When done modifying
the value, press the computer keyboard’s <Enter> key to transmit the new
value to the governor.
Woodward 28
In the figure shown below, the Set Speed A value has been selected for editing.
Parameter Help
To get help on a particular parameter, single click the left mouse button on a
parameter’s Value, then press <Ctrl><F1> on the computer’s keyboard.
<Ctrl><F1> means press and hold the <Ctrl> key while the <F1> key is
pressed and released. This opens the DPG online help file and automatically
jumps to the selected parameter’s help page.
NOTE: Complete online help for each DPG controller is also accessible
by selecting either “Governor Help Contents” or “Parameter Definitions”
from the Universal PST Help menu.
Synchronizing Universal PST with a DPG

Pressing the <Read All> button will load the current values for all of a DPG-
2XXX-00X’s parameters into Universal PST. The <Read All> button is part of
the Table View.
IMPORTANT: If the communication cable is unplugged from a DPG and

plugged into a different DPG while the Universal PST application is still
running, then the <Read All> button must be pressed in order for Universal
PST to synchronize with the new DPG.
The <Write All> button is very useful when reusing saved setup data to
configure a new system with the same data as a previous one. Simply load an
existing set of previously saved parameter values into the Parameter Setup
table using “Open a setup data file” from the File menu then press the <Write
All> button.
Status View
The Status View panel is displayed only after pressing
the <View Status> button. The Status View panel is part
of the Table View display mode.
The Status View panel displays a table where each row

shows the Name of a read only parameter and its
current Value (when “Auto Read is ON”)
Press (left mouse click) the <START Monitoring> button

to have the Universal PST program automatically refresh
the Values. Press the <STOP Monitoring> button to
disable automatic refresh.
Woodward 29
Tuning View
The Tuning View panel is displayed only after pressing the <View Chart>
button. The Tuning View panel is part of the Chart View display mode.
To modify a tuning parameter’s current

value, it must first be selected. Do this by
double-clicking the left mouse button on a
cell in the table that is at the intersection of
the parameter’s row and the Value
column.
The selected cell will be highlighted and

the value can now be modified. When
done modifying the value, press the
computer keyboard’s <Enter> key to
transmit the new value to the governor.
Chart Recorder
The chart recorder is part of the Chart View display mode. Each time Chart
View is entered the last used Data File is reset, the Vertical Scale defaults to
[0 Hz to 12000 Hz], and the Horizontal scale defaults to 20 seconds.
The chart recorder’s display characteristics are configured using the Vertical
Scale options, the Horizontal Scale options, and the Chart Recorder Signal
Filtering options.
The Vertical Scale options provide three different ways to view engine speed
data.
• The [0 to 12000 Hz] option is the default and sets the vertical axis
range to its absolute minimum and maximum measurable values.
• The [_____] to [______] Hz option allows you to enter the minimum
and maximum speed values to zoom in on a viewing range of interest.
• The +/- 10% of [______] Hz option is primarily used to zoom in on the
target speed and center it in the chart recorder. This is most useful
during governor tuning to see if the engine speed stays within +/- 10%
of the target speed during load on/off cycling.
The Horizontal Scale options allow you to set how much data is displayed in
the chart recorder window. Larger values compress the display and show
more data. Smaller numbers expand the display and show less data. A
Horizontal Scale setting of 20 seconds is approximately the same as a 5-
millimeter per second paper travel speed of a conventional paper tape chart
recorder.
The Chart Recorder Signal Filtering options can be used to smooth out noisy
signals. The default setting is Min, which is no filtering. Note that filtering will
round out peaks and give a less accurate display of the speeds actually
measured by the DPG.
Woodward 30
Engine Speed Data Collection

The engine speed data measured by the DPG and displayed in the Universal
PST chart recorder window is also recorded to a computer file.
MPU_DATA00.csv is the default file name used to save engine speed
information. You can change the file name by using the <Data File => button.
The “.csv” data files created to collect engine speed data can be viewed with
either a text editor or with Microsoft Excel. If you load an engine speed data
file into Microsoft Excel, then you can highlight the column of data and use
Excel’s quick graph button to create a line chart of the data.
IMPORTANT: Do not open data files in another program that are

currently being used by Universal PST. Also be sure to close any open
data files needed by Universal PST before starting it.
The <Data File => button opens a dialog box allowing you to set the base file
name where chart recorder data will be saved. A two-digit suffix is
automatically appended to the file name that is given and serves the following
purpose. Each engine speed data file is considered full after recording 60,000
data points which is approximately 10-12 minutes of data. The two-digit suffix
is used to automatically continue collecting data to new files with the same
base file name but with increasing numeric suffixes. The first 60,000 data
points are saved in filename00.csv and the next 60,000 data point are saved
in filename01.csv, and so on until a million data points are collected. This is to
prevent each speed data file from exceeding the 65,536 row limit of Microsoft
Excel.
The <Data Reset> button is used to clear out the data collection buffer and
overwrite the zero suffixed data collection file. Data collection starts from the
beginning of filename00.txt where filename is the base file name previously
used.
The progress bar shown to the right of the <Data Reset> button indicates how
full the complete set of data files is. A total of one million data points
(approximately 3.5 hours of data) can be collected before the progress bar
displays the message “The Data File is FULL”. In order to start recording data
again without overwriting previously collected data, use the <Data File =>
button to create a new base file name in which to receive additional engine
speed information.
The <Pause Chart> button stops chart recorder and Data File updates. After
pressing this button the <Continue> button is displayed. Press the <Continue>
button to turn the chart recorder back on and continue recording engine speed
data to the current target file.
Use the <View Table> button to return to the Table View display mode. Be
sure to open a new Data File before returning to Table View if the data
already collected needs to be saved. The active data file is automatically reset
each time the Chart View display mode becomes active.
Woodward 31
Chapter 5.
Calibration Instructions
Basic Adjustments
The controller is programmed at the factory with default parameter settings. These
settings allow the controller to operate but usually require some further
adjustments to obtain the best system performance. In order to bring the engine
up to a single speed for the first time, the installer will probably need to adjust the
parameters shown in the table below.
The parameters listed are the primary ones to modify to get the governor tuned
and the engine running smoothly. It is recommended that you work with them first
and leave all the other parameters at their default values until you are satisfied
with the basic engine tuning.
ID# Parameter Name Default Value

2 SET SPEED A 1000
5 PROPORTIONAL 25
6 INTEGRAL 50
7 DERIVATIVE 25
8 OVG @ SET SPEED A 20
11 GAIN FACTOR (note 1) 20
12 SPEED FILTER (note 2) 16
NOTE 1: Modify Gain Factor only if you run out of

adjustment in a PID or OVG term.
NOTE 2: For the Speed Filter, typically the value 24

works well on small 3- or 4-cylinder engines. A value
of 16 is recommended for 6- or 8-cylinder engines.
Tuning Methodology
Once the engine is running, the following procedure may be used to discover
more optimum values for PID and the overall gain parameters (OVG). The goal
would be to find PID values that allow the controller to govern the engine well at a
variety of different speeds and loads while only requiring gain adjustment at those
different speeds.
Follow these steps:

1. Set the integral and derivative terms to 0.
2. Set the overall gain low (<20).
3. Increase the proportional term until you get continuous oscillations
greater than 2 Hz.
4. Reduce the proportional term by 25% to 50%.
5. Now experiment with small value changes in the derivative to dampen
out “ringing” in response to load transients.
6. Add some integral to eliminate any steady-state error in the engine’s
speed and help decrease error recovery time.
7. The overall gain can be increased to improve response time while
keeping the ratios of the PID terms relative to each other constant.
Woodward 32
During each of the steps 3 through 6, you need to disturb the system by adding
and removing a load from the engine to check the governor’s response to the load
transition. START WITH SMALL LOADS.
Note that without integral, a speed error may persist after a load-on load-off
transition. Therefore, during steps 3-5 you should temporarily increase the integral
to get the engine speed back to the set speed, and then reset the integral to a
lower value again while working to find good proportional and derivative values.
Repeat steps 3-7 as needed to find a Proportional value, Integral value, and a
Derivative value that work well with a variety of overall gain values and different
load transients.
The Derivative works on the

Instantaneous Rate of Change
The Proportional
in the amount of error
term's output is
unique for each
+E measured error
Error
0 Time
-E
Integration works on
the sum of the errors
accumulated over time
Droop Calibration Procedure

To use Droop, a calibration sequence must be done first.
On DPG-2201-001 Models the calibration sequence can be done only by using

the controller’s built-in user interface.
On DPG-2201-002 Models the calibration sequence can be done by using either

the controller’s built-in user interface or Universal PST.
Woodward 33
Step 1 Make sure the engine is running at the selected set speed and the governor is tuned.
User Interface/ Universal PST: Enter a value of 41 into the Password parameter to
Step 2
allow editing of the droop related parameters.
User Interface: Select the "% DROOP" parameter and adjust its value while the
engine is running with no load applied.
Universal PST: While the engine is running with no load applied, enter a value for the
Step 3 desired percentage of droop in to the "Percent Droop" parameter and press ENTER.
Engine speed will increase to:
[(selected_set_speed) / ((1000 - value_of_%_DROOP) / 1000)].
User Interface: Allow the engine to stabilize at the no load droop speed then press the
controller's ENTER key to set the percent droop.
Universal PST: Allow the engine to stabilize at the no load droop speed. From the
Step 4 Universal PST Status View window, enter the value displayed for the " Actuator %FS"
in to the "No Load Cal" parameter and press ENTER. The engine speed will return to
the selected set speed.
No Load Calibration is now complete.
User Interface: Select the "FULL LOAD CAL" parameter. Engine speed will return to
Step 5 the selected set speed.
Universal PST: Proceed to Step 6.
Now apply full load to the engine and allow the speed to stabilize.
Step 6
(Assumes the governor was previously tuned.)
User Interface: Wait 5 seconds, then press the controller's ENTER key to record the
calibration value.
Universal PST: Wait 5 seconds, then from the Universal PST Status View window,
Step 7
enter the value displayed for the " Actuator %FS" in to the "Full Load Cal" parameter
and press ENTER.
Full load calibration is now complete.
Remove the load from the engine. The engine speed will increase to the no load droop
Step 8
speed. Droop calibration is complete.
After droop calibration, the difference between the No Load Cal and Full Load Cal
parameter value should be greater than 100 for best operation of droop. The
droop function may still work for smaller differences but with less accuracy. You
may be able to get some improvement by modifying or adjusting actuator linkage
or adding springs. The goal is to achieve a wider range of measured current
change through the actuator from no load to full load.
If the calibrated range is too small droop may not work at all. The actuator position
sensing method used by this controller does not work with all actuators. A different
actuator may be required or a different system solution altogether may be needed
by your application, such as an actuator with a position feedback potentiometer
and a supporting controller.
Woodward 34
Chapter 6.
Installation Instructions
Terminal Descriptions
NO. NAME FUNCTION
1 BAT+ Battery positive (9–30 Vdc) *
2 BAT- Battery negative *
3 ACT Actuator drive output
4 ACT Actuator drive return
5 MPU+ Magnetic pickup signal input
6 MPU- Magnetic pickup ground
7 SHIELD Ground connection for cable shielding

Digital input used to select the target set
8 SPEED SEL
speed
9 ILS SIGNAL ILS input used to adjust speed +/- 3%
10 ILS REF (2.5 V) Supply voltage around which ILS operates

Digital input used to decrease the selected
11 DEC SPEED
set speed remotely
Digital input used to increase the selected set
12 INC SPEED
speed remotely
13 +5 Vdc OUT Supply voltage for the digital inputs
(*) DC power buss cable must be less than 10 meters (32.80 feet). All other
cables must be less than 30 meters (98.43 feet).
Recommended Mounting
The controller is designed to be panel mounted and its chassis electrically bonded
to the same protective reference as the engine structure. The mounting should
protect the controller from exposure to rain, weather, and direct sunlight. The
controller should not be mounted on the engine or in an environment that exceeds
the mechanical specifications outlined in Chapter 1 of this manual. The controller
should be mounted in a position to allow access to the user interface, the COMM
port, and the terminal strip.
Woodward 35
Wiring Diagram
DPG-2201-001 &
DPG-2201-002
Dimensions in brackets are millimeters [mm]
Figure 1. Wiring Diagram for DPG-2201-001 and DPG-2201-002
NOTE—DC power buss cable must be less than 10 meters (32.80 feet). All other
cables must be less than 30 meters (98.43 feet).
Woodward 36
Chapter 7.
Diagnostics & Troubleshooting
Display Codes
CODE MEANING
E0 Controller memory failure. Replace controller.
E1 Loss of remote speed potentiometer signal.
Over speed detected. Controller must be turned off

E2
and reset to allow an engine restart.
Actuator drive over current detected. Check wiring.

E3
Check actuator loading.
Troubleshooting Table
SYMPTOM REMEDY
BAT + and BAT – leads are reversed. Check wiring.

LED Display Does Not Light Up
Battery voltage too low. Should measure between 9 and 30 VDC
When Governor Is Powered
Controller is defective. Replace it.
The parameter’s value is the maximum value allowed.
The parameter’s value is the minimum value allowed.
Unable to Modify Parameters A display code is active. Refer to the Display Codes section above
Password protection is enabled. Enter Password
Keypad failure, replace unit.
Actuator leads not connected or shorted.
No fuel source. Turn on fuel source.
Battery voltage is low. Charge or replace the battery.
Set speed is lower than crank speed. Increase the set speed.
Startup Rate setting is too low. The target speed ramps up too slow.
Engine Does Not Start Startup Limit is too low, limiting the actuator drive signal too much.
Is the MPU speed signal present? It should read 2.0 VRMS minimum.
Adjust magnetic pickup (MPU) gap. Try reversing the MPU leads.
If a speed signal is present, measure actuator output duty cycle. If not
greater than 5%, then restore all parameter values to factory default
settings and crank the engine again.
Increase the Proportional value.
Increase the appropriate OVG (overall gain) value.
Engine Over speeds at Startup
Use the Startup Limit.
Decrease the Startup Ramp Rate.
Improve PID tuning.
Integral too low or zero
Engine Does Not Reach
Set Speed Derivative too low or zero
PID values are too low. A tuning that is too soft can prevent the
governor from delivering the needed actuator drive signal to reach the
set speed.
Woodward 37
PID values are too high. Tuning is too hot or oversensitive to small
speed errors, which causes the governor to make large, rapid
changes in actuator drive signal, creating an average signal that is
Engine Does Not Reach inadequate.
Set Speed (cont’d.)
The Integral Low Limit setting is too high. Return the value to the
default setting of zero.
The Integral High Limit setting is too low. Return the value to the
default setting of 99.
Improve PID tuning.
Integral setting is too low.
Engine Takes Too Long to
Startup Rate setting is too low.
Reach the Set Speed
Accel Rate setting is too low.
Speed Filter setting is too high.
Is the LED decimal point blinking? If not, enter password.
Is the selected set speed parameter being modified?
Engine Does Not Track Speed A PID value or an OVG value is too high.
Setting Changes A PID value is too low or zero.
Accel Rate is set too low.
Decel Rate is set too low.
Improve PID tuning.
Use a lower Startup Rate setting.
Excessive Smoke at Startup
Use a lower Startup Limit setting.
Low MPU signal voltage. It should read 2.0 VRMS minimum.
Gain too low.
Sluggish Response to
Improve PID tuning.
Load Changes
Speed filter setting is too high.
Improve PID tuning.
Speed filter setting is too low.
Engine Instability With No Load
Fuel is restricted. Check actuator linkage.
Battery voltage is too low.
Improve PID tuning.
Engine Instability With Load Fuel is restricted. Check actuator linkage.
Battery voltage is too low.
PID values may be too high, causing the governor to overreact and
make large, rapid changes in PWM duty cycle output to the actuator.
Engine Unable to Carry Improve PID tuning.
Rated Load
Torque limit is set too low. Increase the torque limit.
Fuel is restricted. Check actuator linkage.
Measure the ILS input signal to see if the measurement is between
Load Sharing Does Not Work 2.375 VDC and 2.625 VDC.
Use shielded wiring.
The No Load and Full Load values are not calibrated. Perform the
Droop Calibration Procedure.
Difference between No Load and Full Load calibration values is too
Droop Does Not Work small. Should be > 100 for best performance.
Modify or adjust actuator linkage to increase range of actuator loading.
If finer droop control is required, then use a DPG-2223-00X controller.
Woodward 38
Chapter 8.
Service Options
Product Service Options
The following factory options are available for servicing Woodward equipment,
based on the standard Woodward Product and Service Warranty (5-01-1205) that
is in effect at the time the product is purchased from Woodward or the service is
performed:
• Replacement/Exchange (24-hour service)
• Flat Rate Repair
• Flat Rate Remanufacture
If you are experiencing problems with installation or unsatisfactory performance of

an installed system, the following options are available:
• Consult the troubleshooting guide in the manual.
• Contact Woodward technical assistance (see “How to Contact
Woodward” later in this chapter) and discuss your problem. In most
cases, your problem can be resolved over the phone. If not, you can
select which course of action you wish to pursue based on the available
services listed in this section.
Replacement/Exchange
Replacement/Exchange is a premium program designed for the user who is in
need of immediate service. It allows you to request and receive a like-new
replacement unit in minimum time (usually within 24 hours of the request),
providing a suitable unit is available at the time of the request, thereby minimizing
costly downtime. This is also a flat rate structured program and includes the full
standard Woodward product warranty (Woodward Product and Service Warranty
5-01-1205).
This option allows you to call in the event of an unexpected outage, or in advance
of a scheduled outage, to request a replacement control unit. If the unit is
available at the time of the call, it can usually be shipped out within 24 hours. You
replace your field control unit with the like-new replacement and return the field
unit to the Woodward facility as explained below (see “Returning Equipment for
Repair” later in this chapter).
Charges for the Replacement/Exchange service are based on a flat rate plus
shipping expenses. You are invoiced the flat rate replacement/exchange charge
plus a core charge at the time the replacement unit is shipped. If the core (field
unit) is returned to Woodward within 60 days, Woodward will issue a credit for the
core charge. [The core charge is the average difference between the flat rate
replacement/exchange charge and the current list price of a new unit.]
Return Shipment Authorization Label. To ensure prompt receipt of the core,

and avoid additional charges, the package must be properly marked. A return
authorization label is included with every Replacement/Exchange unit that leaves
Woodward. The core should be repackaged and the return authorization label
affixed to the outside of the package. Without the authorization label, receipt of the
returned core could be delayed and cause additional charges to be applied.
Woodward 39
Flat Rate Repair

Flat Rate Repair is available for the majority of standard products in the field. This
program offers you repair service for your products with the advantage of knowing
in advance what the cost will be. All repair work carries the standard Woodward
service warranty (Woodward Product and Service Warranty 5-01-1205) on
replaced parts and labor.
Flat Rate Remanufacture

Flat Rate Remanufacture is very similar to the Flat Rate Repair option with the
exception that the unit will be returned to you in “like-new” condition and carry with
it the full standard Woodward product warranty (Woodward Product and Service
Warranty 5-01-1205). This option is applicable to mechanical products only.
Returning Equipment for Repair

If a control (or any part of an electronic control) is to be returned to Woodward for
repair, please contact Woodward in advance to obtain a Return Authorization
Number. When shipping the item(s), attach a tag with the following information:
• name and location where the control is installed;
• name and phone number of contact person;
• complete Woodward part number(s) and serial number(s);
• description of the problem;
• instructions describing the desired type of repair.
CAUTION
To prevent damage to electronic components caused by improper handling,
read and observe the precautions in Woodward manual 82715, Guide for
Handling and Protection of Electronic Controls, Printed Circuit Boards, and
Modules.
Packing a Control
Use the following materials when returning a complete control:
• protective caps on any connectors;
• anti-static protective bags on all electronic modules;
• packing materials that will not damage the surface of the unit;
• at least 4 inches (100 mm) of tightly packed, industry-approved packing
material;
• a packing carton with double walls;
• a strong tape around the outside of the carton for increased strength.
Woodward 40
Return Authorization Number

When returning equipment to Woodward, please telephone and ask for the
Customer Service Department [1 (800) 523-2831 in North America or
+1 (970) 482-5811]. They will help expedite the processing of your order through
our distributors or local service facility. To expedite the repair process, contact
Woodward in advance to obtain a Return Authorization Number, and arrange for
issue of a purchase order for the item(s) to be repaired. No work can be started
until a purchase order is received.
NOTE
We highly recommend that you make arrangement in advance for return
shipments. Contact a Woodward customer service representative at
1 (800) 523-2831 in North America or +1 (970) 482-5811 for instructions and
for a Return Authorization Number.
Replacement Parts
When ordering replacement parts for controls, include the following information:
• the part number(s) (XXXX-XXXX) that is on the enclosure nameplate;
• the unit serial number, which is also on the nameplate.
How to Contact Woodward

In North America use the following address when shipping or corresponding:
Woodward Governor Company
PO Box 1519
1000 East Drake Rd
Fort Collins CO 80522-1519, USA
Telephone—+1 (970) 482-5811 (24 hours a day)

Toll-free Phone (in North America)—1 (800) 523-2831
Fax—+1 (970) 498-3058
For assistance outside North America, call one of the following international
Woodward facilities to obtain the address and phone number of the facility nearest
your location where you will be able to get information and service.
Facility Phone Number

Brazil +55 (19) 3708 4800
India +91 (129) 230 7111
Japan +81 (476) 93-4661
The Netherlands +31 (23) 5661111
You can also contact the Woodward Customer Service Department or consult our
worldwide directory on Woodward’s website (www.woodward.com) for the name
of your nearest Woodward distributor or service facility. [For worldwide directory
information, go to www.woodward.com/ic/locations.]
Woodward 41
Engineering Services
Woodward Industrial Controls Engineering Services offers the following after-sales
support for Woodward products. For these services, you can contact us by
telephone, by email, or through the Woodward website.
• Technical Support
• Product Training
• Field Service
Contact information:
Telephone—+1 (970) 482-5811
Toll-free Phone (in North America)—1 (800) 523-2831
Email—icinfo@woodward.com
Website—www.woodward.com/ic
Technical Support is available through our many worldwide locations or our

authorized distributors, depending upon the product. This service can assist you
with technical questions or problem solving during normal business hours.
Emergency assistance is also available during non-business hours by phoning our
toll-free number and stating the urgency of your problem. For technical support,
please contact us via telephone, email us, or use our website and reference
Customer Services and then Technical Support.
Product Training is available at many of our worldwide locations (standard

classes). We also offer customized classes, which can be tailored to your needs
and can be held at one of our locations or at your site. This training, conducted by
experienced personnel, will assure that you will be able to maintain system
reliability and availability. For information concerning training, please contact us
via telephone, email us, or use our website and reference Customer Services
and then Product Training.
Field Service engineering on-site support is available, depending on the product

and location, from one of our many worldwide locations or from one of our
authorized distributors. The field engineers are experienced both on Woodward
products as well as on much of the non-Woodward equipment with which our
products interface. For field service engineering assistance, please contact us via
telephone, email us, or use our website and reference Customer Services and
then Technical Support.
Woodward 42
Technical Assistance
If you need to telephone for technical assistance, you will need to provide the following information.
Please write it down here before phoning:
General
Your Name
Site Location
Phone Number
Fax Number
Prime Mover Information

Engine/Turbine Model Number
Manufacturer
Number of Cylinders (if applicable)
Type of Fuel (gas, gaseous, steam, etc)
Rating
Application
Control/Governor Information
Please list all Woodward governors, actuators, and electronic controls in your system:
Woodward Part Number and Revision Letter
Control Description or Governor Type
Serial Number
Serial Number
Serial Number
If you have an electronic or programmable control, please have the adjustment setting positions or the
menu settings written down and with you at the time of the call.
Woodward 43
Woodward 44
We appreciate your comments about the content of our publications.
Send comments to: icinfo@woodward.com
Please include the manual number from the front cover of this publication.
PO Box 1519, Fort Collins CO 80522-1519, USA

1000 East Drake Road, Fort Collins CO 80525, USA
Phone +1 (970) 482-5811 • Fax +1 (970) 498-3058
Email and Website—www.woodward.com
Woodward has company-owned plants, subsidiaries, and branches,

as well as authorized distributors and other authorized service and sales facilities throughout the world.
Complete address / phone / fax / email information for all locations is available on our website.
05/4/M

User Manual: DPG-2201-00X Digital Governor

Uploaded by

Copyright:

Available Formats

User Manual: DPG-2201-00X Digital Governor

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User Manual: DPG-2201-00X Digital Governor

Uploaded by

Copyright:

Available Formats

User Manual

APECS® Programmable Governors for

Electronic controls contain static-sensitive parts. Observe the following

CAUTION—indicates a potentially hazardous situation which, if not avoided, could

Revisions—Text changes are indicated by a black line alongside the text.

ELECTROSTATIC DISCHARGE AWARENESS ................................................. III

CHAPTER 4. UNIVERSAL PST.................................................................... 23

Electrostatic Discharge Awareness

Follow these precautions when working with or near the control.

1. Before doing maintenance on the electronic control, discharge the static

3. Keep plastic, vinyl, and Styrofoam materials (such as plastic or Styrofoam

• Do not touch any part of the PCB except the edges.

• Do not touch the electrical conductors, the connectors, or the

The DPG-2201-00X digital governor is used primarily to govern diesel or gas

Separately programmable Proportional, Integral, and Derivative gains are

DYNA 2000 DYNA 7000 DYNA 8000 APECS 0150

Other Models Available:

DPG-2100 Series – for Genset Applications

User Interface Operation

Remote access to the governor’s parameter settings is available when the

PARAMETER SELECT MODE

INC key Increase the parameter ID number by one

DEC key Decrease the parameter ID number by one

Activate PARAMETER EDIT MODE on the

Display the version number of the

PARAMETER EDIT MODE

INC key Increase the selected parameter’s value.

DEC key Decrease the selected parameter’s value.

Return to PARAMETER SELECT MODE

Save the parameter’s new value, and

INC & DEC Use to display the upper digits of values

INC (increase) Key

DEC (decrease) Key

INC and DEC Keys Together

When values exceeding 9,999 are to Decimal to Hexadecimal

This chapter provides information regarding each parameter’s function. Each of

Subsection numbering corresponds to the parameter numbering on the governor’s

DPG-2201-00X Parameter List

3.1 No. of Flywheel Teeth (optional)

[(MpuHertz ) × (60s )] = [EngineRPM ]

[(3960 Hz ) × (60s )] = [1800 RPM ]

[(EngineRPM ) × (NumberOfTeeth )] = [MpuHertz ]

3.2 Set Speed A (required)

When a two-position switch is connected between SPEED SEL and +5 Vdc

3.3 Set Speed B (optional)

3.4 Idle Speed (optional)

NOTE—When the No. of Flywheel Teeth parameter is used, the SET

3.5 Proportional (required)

Controller output (%)

Each error value produces a unique controller output value

3.6 Integral (required)

Integral response to constant error

3.7 Derivative (required)

Derivative response to changes

Controller output (%)

The error is sampled at regular intervals

When the "Rate of change" changes (red dot) the

3.8 OVG @ Set Speed A (required)

3.9 OVG @ Set Speed B (optional)