Professional Documents
Culture Documents
15cv653 PDF
15cv653 PDF
MODULE – 1: INTRODUCTION
LI
of thermal energy. After the advent of Industrial revolution, human society is increasingly
dependent on fossil fuels for energy. Modern construction employs significant amounts of
energy whether it is thermal energy or energy for transportation.
A
It is useful to recognize different categories of energy consumption in a building,
This may be listed as follows
a) Embodied energy in building materials.
D
b) Energy consumption during building construction.
c) Energy utilized for maintenance during the life span of a building.
d) Energy spent in demolition of the building at the end of its life.
S
Four categories of energies listed above constitute the life cycle energy cost of a building
• Energies in (a) & (b) together the will constitute the energy embodied in a building.
• In item (b), one can consider energy spent in 1) transporting materials to site 2) energy
M
spent in hoisting materials / water 3) energy spent in concrete mixing 4) floor polishing
etc.
• Item c) refers to the energy spent to meet the needs of the occupant of building. Very
A
maintenance energy in buildings since developing countries like India have limited
energy resources vis- a vis the large population
LI
• In all these cases, the basic energy use in the form of thermal energy.
• Many materials also need mechanical processing through electricity energy. For
instance, pugging of clay bricks may use electricity. Grinding the raw materials and
A
clinker in the case of cement manufacture needs electricity.
• Some materials like sand essentially need transportation energy for procurement at site.
D
Table-1: List of Typical Building Materials and Their Energy Content Per Unit of
S Measurement
M
A
IR
SR
LI
Energy
Sl. Typical Size, Brick Energy
Type of Block per Block
No. Block mm Equivalent, Brick
MJ
MJ Energy %
1 Size Stone 180x180x180 0 0 0
A
2 Burnt Brick 230x105x70 4.25 4.25 100
3 Stabilized Mud Block 230x190x100 2.60 1.00 23.5
4 Hollow Concrete Block 400x200x200 12.30 1.32 31.2
5 Steam Cured Block 230x190x100 6.7 2.58 60.6
D
• Stabilized mud block (SMB) is produced by pressing a mixture of soil, sand and cement
in a machine (6% cement is used for stabilization).
• Hallow concrete block had 7% cement in the mixture.
•
S
The steam cured block is made by pressing lime, soil and fly ash mixture and curing in
a steam chamber. Lime percentage is 10% of soil and fly ash.
M
ENERGY IN BUILDINGS
• The total embodied energy in a building depends on the type of technologies used.
• The below table provides a comparison of four different building technologies and the
A
Total Embodied
No of Equivalent Coal
Type of Building Energy per 100m2
Storeys for 100m2, T
GJ
RC framed Construction with
8 421 21
Brick in fill walls
SR
LI
environmental problems like global warming.
There is a need to mitigate these two kinds of environmental problems. Some Typical problem
are discussed below.
A
1) STONE
• Especially granite is extensively used in building construction.
D
• Size stones are used for foundations and walls.
• Crushed stone aggregate is widely used for concrete manufacture.
• Considerable amount of fine granite dust is generated at the site of stone crushing.
•
S
The stone workers inhale the fine dust and succumb to silicosis or tuberculosis
• The entrepreneurs involved in stone processing seem to be have no concern for the health
M
of the workers involved in such activities.
• There is a need to educate the workers about the dangers of stone dust and develop suitable
filters such that inhalation of the fine dust can be avoided.
A
• It is well known that the top soil is a rich source of nutrients for trees and crops and this
nutrient base is depleted by large scale brick manufacturer.
• The landscape is also destroyed by unorganized creation of pits which can render the land
SR
LI
c) Building products like SMB, marble dust+ resin for wash basin.
4) MANGALORE TILES:
A
• The extensive use of firewood for making Mangalore tiles in coastal India has led to
deforestation in the coastal regions.
• It is possible to use natural gas or coal for tile burning.
D
• Use of imported fossil fuel is the only way to save the forest.
• Development of other alternatives to tiles is also desirable to avoid deforestation as well as
fossil fuel burning.
S
5) THE QUESTION OF TIMBER:
•
M
In India, good quality timber is in short supply.
• Timber is imported from Malaysia and Australia.
• Some organization like CPWD, PWD have a tendency to ban the use of timber, because to
A
• Cement based materials cause depletion of fossil fuels and excessive carbon missions
leading to global warming.
• Use of timber also alleviates global warming since the carbon in timber is sorted for a long
period.
• Thus, the timber is a very environmental friendly material, provided it can be procured
without disturbing natural forests.
• The question before the civil engineer is to examine the possibility of growing timber in
non-forest lands in an ecologically sound manner.
• There is a need to avoid ‘PLANTATION ‘type of concepts wherein a single species is
planted.
• There is also a tendency to think only in terms of teak wood.
• There is a need for concerted efforts by foresters and civil engineers to grow all the
LI
available timber species.
.
GLOBAL WARMING
A
• The utilization of fossils fuels like coal and petroleum has been increasing steadily for more
than 200 years after the invention of steam engine and I C engine.
•
D
The carbon –di-oxide in the atmosphere which was bout 280ppm at the beginning of the
industrial revolution, has now reached levels like 354 ppm.
• There has been an explosive growth of research on global warming due to carbon-di-oxide
emissions and other gases released by the industry.
•
S
Many scientists believe that global warming has arrived due to excessive burning of fossil
fuels and the removal of carbon sinks by deforestation.
M
• Several countries across the globe agreed to reduce consumption of fossils fuels over the
coming decades.
• Efforts in this direction are halting, especially since the biggest consumers like the USA is
A
• Industrialisation of these countries will certainly add to the Global warming unless new
low energy strategies are developed.
• In the European Union 40% of the total energy consumption is accounted for buildings
SR
sector.
• The buildings also contribute 30% of the total CO2 emission in European Union.
• This shows that development is invariably associated with high impact on global
environment.
LI
• 56% of the energy is used in the maintenance of the building.
• This shows that buildings consume far more energy during its life time than what is spent
during its construction.
A
• In UK, the energy used by a low rise flat over 25 years is about 12 GJ/m 2, while the energy
content of the building is only 4 GJ/m 2
•
D
In the Indian context, a 2 storeyed brick and RC building consumed 2.65 GJ/m 2 during its
construction, while it consumed 5.83GJ/m2 over a 25-year period.
• India has not reached the levels of developed country like UK in energy consumption.
• Recent trends in air conditions buildings in India can exacerbate the situation since most of
buildings are poorly insulated.
S
• Use of solar passive cooling concepts and improved thermal insulation are needed to
M
mitigate these problems.
• Brick vaulted building with simple solar passive cooling concepts was built which was
showed significant improvements in indoor climate with marginal cost inputs.
A
IR
SR
LI
• Greater the distance of transportation, greater is the consumption of energy and money.
• A variety of transportation vehicles are now available in India, often tempting the users to
procure materials from greater distance.
A
• The below fig Shows the influence of distance and mode of transport on the cost of
transporting 1 cum of soil.
D
S
M
A
IR
• Traditional transport mode like the bullock cart is becoming obsolete in recent times as it
cannot compete with fossils fuel based transportation.
SR
• The fig.1.1 also point out that procuring building material at short distances (local
materials) becomes important for saving energy and costs.
• In case particular material is not available at short distance, it is useful to explore alternative
techniques to perform similar task.
• Example, one can explore the issue of sand for building mortars.
• Bangalore has exhausted nearby sources of sand and it has to be imported from distances
of more than 100 km.
Department of Civil Engineering, MITE 8
Alternative Building Materials and Technologies 15CV653
• Extraction of sand from remote villages is also leading to rapid deterioration of roads and
erosion of river banks due to loss of protective sand cover.
• In this context, if sandy soil is available locally, stabilization of the soil by lime and cement
can easily produce a mortar with a short-term strength of 2.0 MPa.
• Such a mortar will acquire strength of the order 3.0MPa after about one year’s time.
• This could then be local, cost and energy efficient alternative to sand based mortars.
LI
• Alternatively, local sandy soil can be washed to produces sand provided a water resources
is available (water can be recycled)
A
EFFICIENT FOUNDATIONS AND WALLS
D
Use of stones (size stone or random rubble) is quite common in south India for foundation
of walls.
• The modern practices of using cement mortar makes the foundation rather expensive
traditionally, two storeyed buildings have been built on stone-in mud mortar foundation.
•
S
The stress level in the foundation is generally so low that even mud mortars should suffice.
• Use of soil - cement as mortar or soil-lime-cement as mortars should prove to be a cost-
M
effective alternative.
• Use of arched foundations is also a cost-effective alternative.
• Wall construction can be cost effective, if the finish of the masonry unit is so good as to
A
eliminate plastering.
• Good quality SMB or hallow concrete block can lead to such walling solutions.
• Use of cement- soil-sand mortars is also cost effective compared to cement mortar without
IR
• It must be noted that a wall thickness which is less than 225mm can lead to penetration of
heat, especially from East and West facing walls.
• The marginal reduction in cost is then accompanied by a significant thermal discomfort in
the interior.
• Increased use of fans and coolers will also lead to greater energy consumption throughout
the life of the building.
LI
masonry.
• Use of filler slabs, where in tension zone concrete in partially replaced by SMB or bricks
is also cost and energy efficient.
A
• Use of brick domes and vaults can lead to roofing systems which reduce penetration of
solar heat into the building.
•
D
Openings at the crown will facilitate air movement; reduction in the steel used facilitates
reduction in the embodied energy as well.
• For instance, category (A) occurs in most of north India and the buildings should
use cooling techniques in summer while retaining the heat in winter. Well insulated
buildings are needed here.
SR
• In the case of hot and humid environment, air circulation becomes important to
eliminate the discomfort due to humidity.
• In situations like (e) where the winter is very cod (like Ladakh and sub- Himalayan
regions), use of winter heating using solar energy becomes important.
• Concepts like ‘Trombe walls’ which use double glazing on the southern Walls to
capture solar heat are useful.
LI
complete green solution, which is ‘Green Building’.
We can define Green Buildings as structures that ensure efficient use of natural
resources like building materials, water, energy and other resources with minimal generation
A
of non-degradable waste. Technologies like efficient cooling systems have sensors that can
sense the heat generated from human body and automatically adjust the room temperature,
saving energy. It applies to lighting systems too. Green buildings have a smarter lighting
D
system that automatically switches off when no one is present inside the rooms. Simple
technologies like air based flushing system in toilets that avoids water use by 100%, Use of
energy efficient LED’s and CFL’s instead of conventional incandescent lamp, new generation
S
appliances that consume less energy, and many other options helps in making the buildings
green and make them different from conventional ones.
Green buildings are designed to reduce the overall impact of the built environment on human
M
health and the natural environment by:
• Efficiently using energy, water, and other resources
• Protecting occupant health and improving employee productivity
A
• Potential Environmental,
• Economic and Social Benefits.
Green Building refers to the incorporation of environment friendly and resource efficient
SR
processes at each stage of construction, right from site selection and designing to construction,
operation followed by maintenance, renovation or even demolition. The endeavour is to seek
minimum possible impact on environment.
The methods by which the concept in green buildings can achieved are as follows
a) Sustainable Site Selection:
• There should be easy availability of public transport and conveniences so as to cut down
energy consumption for transportation.
• Also, rehabilitation of sites damaged by environmental contamination is a better option
than any new piece of land where large amount of energy and resource is needed to
LI
make the land worthy of building on.
• Already existing landscape, soil and natural features should be protected. For this
reason, hard paving on the site should be avoided to preserve top soil and ease rain
A
water harvesting. There should be minimum storm water runoff.
b) Material and Resources
•
D
Sustainable construction material is chosen keeping in mind various characteristics like
zero or low toxicity, high recyclability, zero or low off gassing of harmful air emissions,
durability, reused and recycled content, sustainably harvested material.
• Dimensional planning and other material efficiency strategies are used to reduce the
S
construction costs. Construction and demolition material can be reused and recycled.
• Use of materials that are available locally is preferred over materials that need to be
M
brought from distant places. It saves transportation costs.
c) Water Efficiency
• Installation of water efficient or low flow equipment’s in kitchens and bathrooms to
A
management and Using treated waste water, non-potable water for site irrigation.
• Raw sewage can be recycled using aquatic plants like duckweed and water hyacinth to
produce clean water suitable for re-use in irrigation and industry.
• Integrating Rain water harvesting system in building design to ensure maximum
possible utilization of rain water.
LI
1) GRIHA
2) IGBC
3) BEE
A
1) Green Rating for Integrated Habitat Assessment (GRIHA)
Green Rating for Integrated Habitat Assessment (GRIHA) is India’s own rating system jointly
D
developed by TERI (The Energy Resource Institute) and the Ministry of New and Renewable
Energy, Government of India. It is a green building design evaluation system where buildings
are rated in a three-tier process. The process initiates with the online submission of documents
as per the prescribed criteria followed by on site visit and evaluation of the building by a team
S
of professionals and experts from GRIHA Secretariat. GRIHA rating system consists of 34
criteria categorised in four different sections. Some of them are
M
1) Site selection and site planning
2) Conservation and efficient utilization of resources
3) Building operation and maintenance
A
4) Innovation.
Commonwealth Games Village, New Delhi, Fortis Hospital, New Delhi, CESE (Centre for
Environmental Sciences & Engineering) Bldg, IIT Kanpur, Suzlon One Earth, Pune and many
IR
The Leadership in Energy & Environmental Design (LEED) is the rating system
developed for certifying Green Buildings. LEED is developed by the U.S. Green Building
Council (USGBC), the organization promoting sustainability through Green Buildings. LEED
is a framework for assessing building performance against set criteria and standard points of
references. The benchmarks for the LEED Green Building Rating System were developed in
year 2000 and are currently available for new and existing constructions.
LI
A
Confederation of Indian Industry (CII) formed the Indian Green Building Council
(IGBC) in year 2001. The vision of the council is, "To enable a sustainable built
D
environment for all and facilitate India to be one of the global leaders in the sustainable
built environment by 2025”. IGBC is the non-profit research institution having its offices in
CII-Sohrabji Godrej Green Business Centre, which is itself a LEED certified Green building.
S
Indian Green Building Council (IGBC) has licensed the LEED Green Building Standard from
the USGBC.
IGBC facilitates Indian green structures to become one of the green buildings.
M
a) The council offers a wide array of services which include developing new green
building rating programmes, certification services and green building training
programmes. The council also organises Green Building Congress, its annual flagship
A
Project teams interested in IGBC Project certification must first register with
IGBC. Registration is the initial step which helps establish contact with IGBC and provides
access to the required documents, templates, important communications and other necessary
information. Once the project is registered, the project team can start preparing for
documentation & calculations to satisfy mandatory requirements and credit submittal
requirements.
LI
The following Green Building rating systems are available under IGBC.
A
2. LEED India for Core and Shell
3. IGBC Green Homes
4. IGBC Green Factory Building
D
5. IGBC Green SEZ
6. IGBC Green Townships
4
5 Birla International School, Jaipur LEED ‘Gold’ rated
6 CII – Sohrabji Godrej Green Business Centre LEED ‘Platinum’ rated
IR
Certification
To achieve the IGBC rating, the project must satisfy all the mandatory requirements
and the minimum number of credit points. The project team is expected to provide supporting
documents at preliminary and final stage of submission, for all the mandatory requirements
and the credits attempted.
The project needs to submit the following
LI
• Filled-in Template
• Narratives and supporting documentation such as drawings, calculations declarations,
contract documents, purchase invoices, manufacturer cut-sheets, letters, material test
A
reports, etc., for each mandatory requirement/ credit.
The project documentation is submitted in two phases preliminary submittal and final
submittal:
D
Preliminary Phase: It involves submission of all documents, which shall include mandatory
requirements and the minimum number of credits. After the preliminary submission, review is
done by third party assessors and review comments would be provided within 30 working days.
S
Final Phase: It involves submission of clarifications to preliminary review queries and final
submittal. This review will also be provided within 30 working days, after which the rating is
M
awarded.
A
IR
SR
LI
• Development of LEED began in 1993, headed by Natural Resources Defence
Council (NRDC) led by senior scientist Robert K. Watson he brought together non-
profit organizations, government agencies, architects, engineers, developers, builders,
A
product manufacturers and other industry leaders.
• LEED grew from one standard for new construction to a comprehensive system of
interrelated standards covering aspects from the design and construction to the
D
maintenance and operation of buildings.
• LEED standards have been applied to approximately 83,452 registered and certified
LEED projects worldwide, covering around 1.28 billion square meters.
•
S
Proposals to modify the LEED standards are offered and publicly reviewed by
USGBC's member organizations.
Rating systems
M
LEED has evolved since 1998 to more accurately represent and incorporate emerging
green building technologies.
1) The Pilot Version
A
may choose between LEED 2009 and LEED v4. New projects registering after October
31, 2016 must use LEED v4).
LEED 2009 encompasses Ten rating systems for the design, construction and operation of
buildings, homes and neighbourhoods. Five overarching categories correspond to the
specialties available under the LEED professional program. That suite currently consists of the
following
LI
LEED for Existing Buildings: Operations & Maintenance
d) Green Neighbourhood Development
LEED for Neighbourhood Development
A
e) Green Home Design and Construction
LEED for Homes (The LEED for Homes rating system is different from LEED v3, with
different point categories and thresholds that reward efficient residential design).
D
Under LEED 2009, there are 100 possible base points distributed across six credit categories:
1) Sustainable Sites
2) Water Efficiency
S
3) Energy and Atmosphere
4) Materials and Resources
M
5) Indoor Environmental Quality
6) Innovation in Design
Up to 10 additional points may be earned: four additional points may be received for Regional
A
Certification level
IR
The LEED 2009 performance credit system aims to allocate points "Based on The
Potential Environmental Impacts and Human Benefits of Each Credit". These are
weighed using the environmental impact categories of the United States Environmental
Protection Agency's Tools for the Reduction and Assessment of Chemical and Other
Environmental Impacts (TRACI) and the environmental-impact weighting scheme
developed by the National Institute of Standards and Technology (NIST).
Prerequisites
To participate in LEED 2009, a building must comply with environmental laws and
LI
regulations, occupancy scenarios, building permanence and pre-rating completion, site
boundaries and area-to-site ratios. Its owner must share data on the building's energy and water
use for five years after occupancy (for new construction) or date of certification (for existing
buildings). Each of the performance categories also have mandatory measures in each category,
A
which receive no points.
D
The weighting process has three steps
2) NIST weightings are used to judge the relative importance of these impacts in each
category.
M
3) Data regarding actual impacts on environmental and human health are used to assign
points to individual categories and measures.
A
This system results in a weighted average for each rating scheme based upon actual impacts
and the relative importance of those impacts to human health and environmental quality. The
LEED council also appears to have assigned credit and measure weighting based upon the
IR
More stars mean more energy efficiency. BEE has developed the Energy Performance Index
(EPI). The unit of Kilo watt hours per square meter per year is considered for rating the building
and especially targets air conditioned and non-air-conditioned office buildings. The Reserve
Bank of India’s buildings in Delhi and Bhubaneshwar, the CII Sohrabji Godrej Green Business
Centre and many other buildings have received BEE 5 star ratings.
Rainwater Harvesting
LI
tools. Its uses include water for gardens, livestock, irrigation, domestic use with proper
treatment, indoor heating for houses, etc. The harvested water can also be used as drinking
water, longer-term storage, and for other purposes such as groundwater recharge.
A
Advantages
a) Rainwater harvesting provides an independent water supply during regional water
D
restrictions, and in developed countries, is often used to supplement the main supply.
b) It provides water when a drought occurs, can help mitigate flooding of low-lying areas,
and reduces demand on wells which may enable groundwater levels to be sustained.
c) It also helps in the availability of potable water, as rainwater is substantially free of
salinity and other salts.
S
d) Application of rainwater harvesting in urban water system provides a substantial
M
benefit for both water supply and waste water sub systems by reducing the need
for clean water in water distribution system, less generated storm water in sewer
system, and a reduction in storm water runoff polluting freshwater bodies.
A
enhance irrigation in arid environments, ridges of soil are constructed to trap and prevent
rainwater from running down hills and slopes. Even in periods of low rainfall, enough water is
collected for crops to grow. Water can be collected from roofs, and dams and ponds can be
SR
constructed to hold large quantities of rainwater so that even on days when little to no rainfall
occurs, enough is available to irrigate crops.
Quality
• The concentration of contaminants is reduced significantly by diverting the initial
flow of run-off water to waste. Improved water quality can also be obtained by using a
floating draw-off mechanism by using a series of tanks, withdraw from the last in series.
• Prefiltration is a common practice used in the industry to ensure that the water entering
the tank is free of large sediment. Prefiltration is important to keep the system healthy.
LI
• Supplying rainwater that has gone through preliminary filtration measures for non-
portable water uses, such as toilet flushing, irrigation and laundry, may be a significant
part of a sustainable water management strategy.
A
System setup
•
D
Rainwater harvesting systems can range in complexity, from systems that can be
installed with minimal skills, to automated systems that require advanced setup and
installation.
• The basic rainwater harvesting system is more of a plumbing job than a technical job,
S
as all the outlets from the building terrace are connected through a pipe to an
underground tank that stores water.
•
M
Systems are ideally sized to meet the water demand throughout the dry season, since it
must be big enough to support daily water consumption. Specifically, the rainfall
capturing area such as a building roof must be large enough to maintain adequate flow
A
of water. The water storage tank size should be large enough to contain the captured
water.
• For low-tech systems, many low-tech methods are used to capture rainwater: rooftop
IR
systems, surface water capture, and pumping the rainwater that has already soaked into
the ground or captured in reservoirs and storing it in tanks (cisterns).
• Before a rainwater harvesting system is built, use of digital tools is useful. For instance,
SR
LI
local climate performing an accurate site analysis. Elements to be considered include window
placement and size, and glazing type, thermal insulation, thermal mass, and shading. Passive
solar design techniques can be applied most easily to new buildings, but existing buildings can
A
be adapted or "retrofitted".
Passive Energy Gain
D
S
M
Passive solar technologies use sunlight without active mechanical systems. Such
technologies convert sunlight into usable heat, cause air-movement for ventilating, or
future use, with little use of other energy sources. Passive cooling is the use of the same
IR
• More widely, passive solar technologies include the solar furnace, but this typically
requires some external energy for aligning their concentrating mirrors or receivers, and
historically have not proven to be practical or cost effective for widespread use. 'Low-
grade' energy needs, such as space and water heating, have proven over time to be better
applications for passive use of solar energy.
LI
A
D
S
The ability to achieve these goals simultaneously is fundamentally dependent on the
seasonal variations in the sun's path throughout the day. This occurs as a result of
the inclination of the Earth's axis of rotation in relation to its orbit. The sun path is unique for
M
any given latitude.
In Northern Hemisphere, non-tropical latitudes farther than 23.5 degrees from the equator:
A
• The sun will reach its highest point toward the south (in the direction of the equator).
• As winter solstice approaches, the angle at which the sun rises and sets progressively
IR
moves further toward the South and the daylight hours will become shorter
• The opposite is noted in summer where the sun will rise and set further toward the North
and the daylight hours will lengthen.
SR
The converse is observed in the Southern Hemisphere, but the sun rises to the east and sets
toward the west regardless of which hemisphere you are in.
In equatorial regions at less than 23.5 degrees, the position of the sun at solar noon will oscillate
from north to south and back again during the year.
In regions closer than 23.5 degrees from either north-or-south pole, during summer the sun will
trace a complete circle in the sky without setting whilst it will never appear above the horizon
six months later, during the height of winter.
The 47-degree difference in the altitude of the sun at solar noon between winter and summer
forms the basis of passive solar design. This information is combined with local climatic data
(degree day) heating and cooling requirements to determine at what time of the year solar gain
LI
will be beneficial for thermal comfort, and when it should be blocked with shading. By strategic
placement of items such as glazing and shading devices, the percent of solar gain entering a
building can be controlled throughout the year.
A
One passive solar sun path design problem is that although the sun is in the same relative
position six weeks before, and six weeks after, the solstice, due to "Thermal Lag" from
D
the thermal mass of the Earth, the temperature and solar gain requirements are quite different
before and after the summer or winter solstice. Movable shutters, shades, shade screens, or
window quilts can accommodate day-to-day and hour-to-hour solar gain and insulation
requirements.
S
Key Passive Solar Building Configurations
• In a direct-gain passive solar system, the indoor space acts as a solar collector, heat
absorber, and distribution system.
• South-facing glass in the northern hemisphere (north-facing in the southern
SR
hemisphere) admits solar energy into the building interior where it directly heats
(radiant energy absorption) or indirectly heats (through convection) thermal mass in the
building such as concrete or masonry floors and walls.
• The floors and walls acting as thermal mass are incorporated as functional parts of the
building and temper the intensity of heating during the day. At night, the heated thermal
mass radiates heat into the indoor space.
LI
There are two types of indirect gain systems
1) Thermal Storage Wall Systems
2) Roof Pond Systems.
A
1) Thermal Storage (Trombe) Walls
•
D
This wall system was first envisioned and patented in 1881 by its inventor, Edward
Morse Felix Trombe, for whom this system is sometimes named, was a French engineer
who built several homes using this design in the French Pyrenees in the 1960s.
• In a Thermal Storage Wall system, often called a Trombe Wall, a massive wall is
S
located directly behind south-facing glass, which absorbs solar energy and releases it
selectively towards the building interior at night.
•
M
The wall can be constructed of cast-in-place concrete, brick, adobe, stone, or solid (or
filled) concrete masonry units. Sunlight enters through the glass and is immediately
absorbed at the surface of the mass wall and either stored or conducted through the
material mass to the inside space.
A
• Temperatures of the air in this space can easily exceed 49 °C. This hot air can be
introduced into interior spaces behind the wall by incorporating heat-distributing vents
IR
LI
• It can be left unglazed or can be covered by glazing. Solar radiation heats the water,
which acts as a thermal storage medium. At night or during cloudy weather, the
containers can be covered with insulating panels. The indoor space below the roof pond
A
is heated by thermal energy emitted by the roof pond storage above.
• Roof pond systems perform better for cooling in hot, low humidity climates. Not many
D
solar roofs have been built, and there is limited information on the design, cost,
performance, and construction details of thermal storage roofs.
In cold climates, double glazing should be used to reduce conductive losses through the
glass to the outside. Night-time heat loss, although significant during winter months, is
not as essential in the sunspace as with direct gain systems since the sunspace can be
IR
• The internal surfaces of the thermal mass should be dark in colour. Movable insulation
(e.g., window coverings, shades, shutters) can be used help trap the warm air in the
sunspace both after the sun has set and during cloudy weather. When closed during
extremely hot days, window coverings can help keep the sunspace from overheating.
• To maximize comfort and efficiency, the non-glass sunspace walls, ceiling and
foundation should be well insulated. The perimeter of the foundation wall or slab should
be insulated to the frost line or around the slab perimeter.
MODULE – 2
ELEMENTS OF STRUCTURAL MASONRY
Introduction
A large proportion of masonry buildings for residential and other purposes is
satisfactorily designed and built in accordance with empirical rules and practices without the
need for special structural consideration. However, the limits of this approach cannot be
extended much beyond the scale of two-storey houses of very conventional construction
without having to use very thick walls, which in turn result in waste of materials and other
LI
disadvantages.
Indeed, for a considerable time this led to the eclipse of masonry as a structural material for
larger buildings, and it is only since the 1950s that the application of structural engineering
A
principles to the design of masonry has resulted in the re adoption of this material for certain
The economic success of masonry construction has been achieved not only by the
S
rationalisation of structural design, but also because it is possible for the walls which comprise
a building structure to perform several functions which in a framed structure have to be
M
provided-for separately.
Thus, masonry walls simultaneously provide structure, subdivision of space, thermal and
A
acoustic insulation, as well as fire and weather protection. The material is relatively cheap and
durable, can provide infinite flexibility in plan form and can offer an attractive external
IR
To make the best use of these inherent advantages in multi-storey buildings it is necessary to
use masonry construction in cases where the accommodation gives rise to moderate or small
floor spans and where it is possible to continue the loadbearing walls uninterrupted from
foundations to roof.
In some buildings where there has been a need for large spans on the first and second floors
(for example, in hotels), these floors have been built in framed construction with loadbearing
walls above this level.
Masonry Materials
Masonry can be regarded as an assemblage of structural units, which are bonded
together in a particular pattern by mortar or grout.
Structural Units
There are seven types of structural unit referred to in IS: 1905 – 1987, they are as follows
1) Burnt Clay Building Bricks
2) Stones (in regular sized units)
3) Sand Lime Bricks
4) Concrete Block
LI
5) Lime Based Blocks
6) Burnt Clay Hollow Blocks
7) Gypsum Partition Blocks
A
8) Autoclaved Cellular Concrete Blocks
D
The selection of a particular type of unit for any given structure is dependent on a
number of criteria, e.g. strength, durability, adhesion, fire resistance, thermal properties,
acoustic properties and aesthetics. The structural units may be solid, solid with frogs,
S
perforated, hollow or cellular, as indicated in Figure
M
A
IR
Mortar
SR
Mortar is the medium which binds together the individual structural units to create a
continuous structural form, e.g. brickwork, stonework, etc.
• Mortar serves a number of functions in masonry construction as follows
• Bind together the individual units
• Distribute the pressures evenly throughout the individual units.
• Infill the joints between the units and hence increase the resistance to moisture
penetration
• Maintain the sound and thermal characteristics of wall.
Present-day mortars are specifically manufactured to suit the type of construction involved. In
most cases they are mixtures of sand, cement and water. The workability is often improved by
the inclusion of lime or a mortar plasticiser. Lime is used in mortar for several reasons
• To create a consistency which enables the mortar to cling and spread
• To help retain the moisture and prevent the mortar from setting too quickly
• To improve the ability of the mortar to accommodate local movement.
LI
Three types of burnt bricks may be mentioned in today’s Indian context namely
1) Country Bricks
A
2) Table Mould Bricks
3) Wire Cut Bricks
Country Bricks
•
•
D
Country bricks are made using a simple four sided mould.
These bricks are moulded by the ‘Soft Mud’ process whose soil has a high moisture
S
content facilitating easier pressing.
The moulding is done on level ground and the wet brick is left on the ground to dry.
M
•
• After drying the bricks are stacked in a clamp and burnt using fire wood or paddy husk.
A
• The use of lesser moisture at the time of moulding leads to an improved shape and
strength for the brick.
SR
• The wet brick is released by turning the mould upside down on a level platform.
• These bricks generally have frog on one of the bedding faces.
• These bricks are then dried in shade and then burnt in a continuous kiln known as the
Bull’s Trench Kiln.
• New simpler kiln has been developed in recent years, this may be called as a clamp kiln
• The table mould brick is generally much stronger than the country brick. Strength
ranges from 3.5MPa to 7.0 MPa is quite common for such bricks.
• Recently, a new type of mould was developed at ASTRA. For the table mould brick.
This mould has four sides with a removable plate in the position of the 5th side.
• The plate sits at the bottom of the mould but cannot be taken out through the bottom
because of stopper in the corners.
• After moulding the brick, the mould may be turned upside down on a platform and it
may be taken out while pressing on the removable plates.
• The plates remain on the wet bricks to be taken out subsequently. This mould has been
tested recently and lead to bricks of strength of bricks of strength 4.5 MPa.
LI
• This slab is then sliced by a wire frame into a number of bricks.
• After drying, the bricks are burnt in a Hoffman’s kiln.
A
• A good wire cut brick retains a good shape and often has strengths in the range of 10.0
MPa to 20.0 MPa
•
•
It is a very expensive brick.
D
It must be pointed out that a wire cut brick of 10.0MPa strength can be conveniently
S
used for load bearing masonry going up to 5 storeys without using RC frames.
• This may be quite cost effective compared to framed construction.
M
A
IR
SR
Three types of stones are available for construction of wall such as Igneous rock- ex: Granite
and Basalt, Sedimentary rock – ex: Limestone and Sand stone and Metamorphic cock – ex:
Gneiss and Marble
1) All stones have a good compressive strength which is often more than adequate for wall
construction.
2) Granite shows the highest strength and it is also known for its durability.
3) Fine grained stones are stronger than coarse grained stones.
4) Sandstone and Basalt are less durable although they do not deteriorate in time spans of
LI
the order a couple of centuries.
5) Sand stone temples built in Aihole and Pattadakal in 6th and 8th centuries show sign of
A
erosion
6) Basalt used in Gol Gumbaz and Ibrahim Rouza in Bijapur in the 16th century is showing
considerable deterioration.
D
7) However, these stones may be considered alright for normal buildings where a life span
S
of 200years.
Laterite
M
gave an average strength of 1.7 MPa. Recent study gave a compressive strength in the
range of 1.04 to 3.47 MPa.
• Out of 13 locations studied, 11 locations showed strength below 2.5MPa.
• Laterite blocks from Calicut, tested, gave an average compressive strength of 3.8 MPa.
• These studies show that Laterite strength can be sometimes much lower than what is
specified by BIS Code of practice which says that the average strength must be 3.5MPa.
• When Laterite blocks of thickness of morethan, 190mm is ued, it is possible to use
blocks of strength 2.0-2.5 MPa. It is desirable to avoid blocks of strength much lower
than 2.0MPa.
LI
which contains more amount of silt like fines. The BIS prescribes a minimum of 2.0MPa for
concrete block. The hollow can be deceptive by looks but can have low strengths.
It must also be mentioned that there are good manufacturers who produce good quality of block
A
having a strength of 7.4MPa. Such blocks can be cost effective and since hollow block is having
D
lower densities it is having advantage in construction of 3 to 4 storeys.
The use of solid concrete block is also common. The Rajasthan Avas Vikas Sansthan
has come up with a simple machine to make solid concrete blocks. It is relatively easy to
S
achieve desirable strength like 4.0MPa to 5.0MPa with a solid block. However, the density of
such block will be high and may not be suites for more than 2 storeyed construction.
M
• Burnt clay hallow block made by a process of extrusion. The thickness of a hallow
block is as low as 1.5 to 2.0 cms, they came with various sizes.
IR
• These blocks give a relatively high strength when tested with load parallel to the holes,
when the blocks are laid with holes aligned horizontally the strength is subsequently
SR
less.
• These blocks have a rather favourable weight/ strength ratio, they can be quite useful
in planning a building with several storeys since the dead load weight can be kept low.
• They also offer possibilities of improved thermal comfort when the wall thickness is
200 mm or more and then external walls are painted white or some light colours.
• The only restriction to their use is their high cost.
• Prove to useful at places close to the factories manufacturing them.
FaL- G Bricks
• FaL-G is the name of the product named after its ingredients, Fly ash, Lime and
Gypsum.
• FaL-G brick is a building material, specifically masonry units, containing class C or
class F fly ash and water. Compressed at 28 MPa and cured for 24 hours in a 66
°C steam bath, then toughened with an air entrainment agent, the bricks last for more
than 100 freeze-thaw cycles.
• Owing to the high concentration of calcium oxide in class C fly ash, the brick is
described as "Self-Cementing". The manufacturing method saves energy,
LI
reduces mercury pollution, and costs 20% less than traditional clay brick
manufacturing.
A
• Ever since FaL-G (Fly Ash-Lime-Gypsum) process is introduced in 1991, fly ash brick
activity has been revolutionised in India. FaL-G technology developed and patented by
D
Dr Bhanumathidas and Kalidas has simplified the process by adding gypsum to fly ash
+ lime/cement, converting the calcium aluminates into calcium alumino-sulphates
resulting in to achieve high early strengths. Thus FaL-G brick does not need any
S
pressure and gets cured at ambient temperature of 20-40 °C.
• By avoiding both press and heating chamber, FaL-G process has brought down the
M
multi-million plant cost to a few lakhs, within the reach of micro units.
The raw materials for Fly Ash Bricks are:
A
Material Mass
IR
The strength of fly ash brick manufactured with the above compositions is normally of the
order of 7.5 N/mm2 to 10 N/mm2. Fly ash bricks are lighter and stronger than clay bricks.
Main ingredients include fly ash, water, quicklime or lime sludge, cement, aluminium powder
and gypsum.
The block hardness is being achieved by cement strength, and instant curing mechanism by
autoclaving. Gypsum acts as a long-term strength gainer. The chemical reaction due to the
aluminium paste provides the bricks its distinct porous structure, lightness, and insulation
properties, completely different compared to other lightweight concrete materials. The finished
product is a lighter Block - less than 40% the weight of conventional Bricks, while providing
the similar strengths. The specific gravity stays around 0.6 to 0.65, hence by using these blocks
in structural buildings, the builder saves around 30 to 35% of structural steel, and concrete, as
these blocks reduce the dead load on the building significantly.
FaL-G process is practiced in two ways
Lime Route: The composition is fly ash (60%) slaked lime (30%) and anhydrite gypsum (10%)
to which 3 to 4 times of stone dust, sand or any inert filler material can be added.
Cement Route: The composition is fly ash (76%), OPC (20%) and anhydrite (4%) to which 3
LI
to 4 times of filler material can be added.
Advantages
A
1) It reduces dead load on structures due to light weight (2.6 kg, dimension: 230 mm X
110 mm X 70 mm).
D
2) Same number of bricks will cover more area than clay bricks
3) High fire Insulation
S
4) Due to high strength, practically no breakage during transport and use.
5) Due to uniform size of bricks mortar required for joints and plaster reduces almost by 50%.
M
6) Due to lower water penetration seepage of water through bricks is considerably reduced.
7) Gypsum plaster can be directly applied on these bricks without a backing coat of lime
A
plaster.
8) These bricks do not require soaking in water for 24 hours. Sprinkling of water before use
IR
is enough.
Disadvantages
SR
1) Mechanical strength is low, but this can be rectified by adding marble waste or mortar
between blocks.
2) Limitation of size. Only modular size can be produced. Large size will have more
breakages.
3) It is only good for the places like subtropical area or area where climate is warm because it
doesn't absorb heat. But during cold it is not helpful.
CONCEPT
1) When the Soils are compressed using external energy, the density of the soil reaches a
LI
value of a moisture content known as the optimum moisture content (OMC)
2) The value of OMC and the maximum density depends on the energy input during
compaction.
A
3) The process of mechanical compression can lead to densification and strengthening of
the soil.
D
4) If soil also stabilized against loss of strength during saturation, we can think of a
stabilized mud (soil) block where the stabilization is achieved by a combination of
S
densification and mixing of a stabilizing additive.
5) A variety of materials can be used for the stabilization namely: cement, lime and
M
bitumen.
A
RAW MATERIALS
The raw materials required are
IR
proportion 2% can added for stabilization. Lime has the advantage of combining with clay in
the soil and enhancing the long-term durability
THE PROCESS:
1) Sieve the soil in a 4mm sieve to remove the stones and lumps of clay and Mix sand or
quarry dust to correct the clay-sand percentage in the soil, Add cement or cement and
lime in appropriate proportion.
2) Sprinkle moisture onto the mixture and further mix thoroughly till the mixture is
homogeneous and Test for optimum moisture content by trying to make a ball of soil
LI
in the hand. If a ball can be made without the soil sticking to the hand the moisture
content is right.
3) Weight the correct amount of moist soil such that a fresh block density of 2.05 gm/cc
A
can be achieved. The weight depends on the volume of the finished block. In case the
D
soil contains the much sand and silt a density of 2.05gm/cc may not be feasible.
Densities like 2.0gm/cc or 1.95gm/cc may be attempted.
4) The weighed soil is now poured into a soil compaction press like the Mardini. The block
S
is now pressed by operating the toggle lever, after closing the lid, the ejected block is
then stacked in a five or six block high stack for curing.
M
5) Sprinkling the moisture may be pursued up to 21 days to complete the block making
process.
A
• The block size larger than the size of brick to achieve economy in the production of the
materials. Usual sizes are 230x190x100mm or 305x143x100mm
SR
• Block thickness less than 100mm can be easily made, by introducing thicker plates
inside the plates. A half block size of 230x108x100mm is also sometimes useful for
corner joint, door and windows jambs, partition walls and so on.
LI
• The below Table shows the influence of cement on the strength of SMB cubes of size
76mm.
A
• The soil had a sand content of 65% and a clay content of 17%. As the cement percentage
is increased from 5% to 7.5% the wet compressive strength increases by about 60%
•
STRENGTH OF BLOCKS
D
A cement content of 6.0 to 7.0%is normally advisable for building two storied houses.
S
• THE SMB technology is well suited to produce a range of block strengths at the site.
M
• As a rule a minimum wet compressive strength of 3.0MPa is desirable for two storeyed
house constructions.
• A cement percentage of 6 to 7% and a sand content of 65% and a clay content of 15%
A
• Using higher percentage of cement, wet compressive strength in the range of 4.0 to
7.0MPa can easily achieved.
• A block with 7.0MPa strength can be easily comfortably recommended for four
SR
LI
moulds of six blocks. These moulds are made of 4mm thick M S sheet and are welded
from outside.
5) A smooth level and hard surface is required for casting the block and the stone masonry
A
blocks are made of large size stone pieces bonded together with lean- cement –concrete
D
mix of 1:5:8 (cement: sand: stone aggregate 10mm and lees).
6) The stone pieces used are as large as can be accommodated in the mould, these can
from 5to 26cm in size and obtained either from quarry or breaking the river boulders.
S
7) These blocks are used both load bearing as well as non-load bearing walls, the thickness
of the wall depends upon the load coming over it.
M
9) This technology has been implemented in a large number of locations in India, where
stone is readily available.
IR
1) Steam curing is a process for hardening concrete, cement, and mortar that involves
exposure to warm steam. Materials subjected to this hardening technique tend to cure
more uniformly and also much more quickly than those hardened via other processes.
2) There are some disadvantages to this process that must be considered before deciding
to use it for curing, and there may be certain applications where this method is not
appropriate.
3) In steam curing, objects to be cured are placed inside a chamber or room. Using a
control panel, an operator can set the temperature and humidity level. Variations in
pressure may also be possible, depending on the device. The heat and moisture
penetrate the materials quickly to fully hydrate and harden them.
4) Steam curing requires a fraction of the time involved with traditional curing and quickly
strengthens the products so they can be used immediately. The alternative to steam
curing is allowing products to cure naturally at ambient temperatures and humidity
levels.
5) Timing is important when using concrete, cement, and mortar, since cool, moist
weather tends to provide the best cure. Dry, hot weather will cause weakness and
cracking that may compromise the finished product and in some cases, the damage can
be extensive enough that the product cannot be used.
6) This is an especially important consideration when working outdoors, where
LI
controlling temperatures and humidity levels is not possible. The problem with steam
cured cement is that in the long term, the cement may be weaker.
7) Steam cured cement, concrete, and mortar products are stronger at the outset than
A
traditionally cured products, but they are more likely to fracture, crumble, and develop
D
other problems later in their useful lives. This may not be a concern in all situations,
but it can become a serious issue in others.
8) Variations in the temperature and humidity levels used during curing that change the
S
length of time required will also vary the long-term strength of the product.
• Steam cured stabilized mud blocks
M
MODULE – 3
ALTENATIVE BUILDING MATERIALS
LIME-POZZOLANA CEMENTS
INTRODUCTION
Engineers and the general public often have the impression that use of lime in building
construction is a retrograde step and that it can never compete with a modern material like
Portland. This impression is perhaps correct, as long as one is thinking of concretes with
strengths in excess of 15.0MPa. However, it must be observed that nearly half the cement in a
building is used for low strength applications like plasters and mortars where the strength
requirement if often as low as 3.0MPa. Portland cement is certainly not the best material if one
looks at the requirements of a mortar that it should be preferably slow setting and have high
level of plasticity and flow.
Although BIS includes mixing of cement and lime in mortars, it is never used in practice
due to the inherent prejudices against lime. It is necessary here to emphasize that addition of
lime to cement mortars, slows down the initial setting of cement. Such mortars can be used
effectively over a much longer time after addition of water. Cement between brick and the
bonding of brick and mortar are very much improved by addition of lime. It is hence necessary
to recognize the inherent value of lime in the preparation of building mortars.
RAW MATERIALS
LIME STONE
One of the raw materials for all lime based mortars is lime stone. Lime stone is
essentially calcium carbonate in nature. Calcium being one of the fairly abundant metals on
earth. Natural lime stone is one of the purer forms of calcium carbonate occurring in nature.
Calcium carbonate is mildly soluble in water and sometimes be leached out by water and
ultimately deposited with clay as an impurity in the form of ‘Kankar’ lime stone.
There is also an organic source of lime stone in the form of shell lime which is usually
available in coastal areas. All the three sources of lime stone are used for building purposes.
The ‘Kankar’ variety of lime stone usually displays hydraulic properties after burning.
The requirements for the use of lime for building purposes may be obtained by
codes/specifications
IS:712-1973 : Specifications for Building Limes
IS:1514-1959 : Methods of sampling and test for quick lime and hydrated lime.
IS:6932-1973 : Methods of tests for building limes.
POZZOLANA
Pozzolana is a material which consists essentially of amorphous silica or a mixture of
amorphous silica and alumina. This is not cementitious by itself, but forms cementitious
compounds when it combines with calcium hydroxide at ambient temperature in the presence
of moisture. A mixture of finely ground calcium hydroxide and pozzolana is hence known as
lime- pozzolana cement.
There are many ways in which pozzolana can be produced. The following sources of
pozzolana are commonly used.
1. Powdered burnt clay (commonly known as ‘Surkhi’ in India)
2. Fly ash.
3. Rice husk ash
Honeycomb Kiln
It is an annular honey comb brick structure is erected and a closely spaced mesh is
placed at a height of 20cms above the ground.
Alternate layers of rice husk and clay are placed in the kiln such that the husk is about
30 to 40% by weight of the clay.
The width of the clay layers should about 15cms less than the width of husk to permit
easy air movement through the bed of husk.
The stack is now set fire to from below and the entire mass burns out over one or two
days.
The end product is a mixture of burnt clay and rice husk, this may be ground in a ball
mill to obtain fine pozzolona.
Combination pozzolona, is obtained from this process, which is a mixture of burnt clay
and rice husk ash, and This technique has the advantage of producing a relatively large
quantity of pozzolona.
It must be noted that the national availability of rice husk ash is around 2.0 million
tonnes of combination pozzolona can be generated to the country.
THE PROCESS
LIME - POZZOLONA CEMENT
It is an intimate mixture of lime and pozzolona will set in the presence of water, forming
calcium silicate and calcium aluminates compounds.
In the traditional lime Surkhi mortar, slaked lime and brick powder is mixed and ground
in the presence of moisture in bullock driven mortar mills and the ground moist mixture
is then directly used in construction.
In the modern context, power-driven pan mills are used to grind the mortar.
Unlike Portland cement, which is already a complete cementitious product, lime
pozzolona cement needs an additional step of mixing lime pozzolona. The efficiency
of the lime pozzolona cements depends on the intimacy of the mixing of lime and
pozzolona.
The traditional process of lime Surkhi mortar involved wet grinding of lime and Surkhi
mixture. According to the studies made in KERS Dam site, it was found that the mortar
strength reaches a maximum when the duration of grinding in 35 minutes. Grinding for
longer or shorter durations leads to lower strengths.
However, in the context of modern construction wet grinding may be considered to be
an inconvenient procedure, since this needs deployment of diesel engine or electric
energy at the site for mortar mixing. It would be ideal if wet grinding can be avoided.
Two alternative techniques have been explored at Dept. of Civil Engineering IISc Bengaluru
a) Dry blending of lime and pozzolona
b) Wet blending of lime and pozzolona
This also leads to the question of shelf life of lime pozzolona mixture. It was found that
lime pozzolona mixture will lose strength rapidly on storage.
Stored in gunny bags or LDPE bags, the day’s strength shows a 60%reduction after
21days of storage.
Important to note that the blended dry mixture of lime and pozzolona should not be
stored for more than 14 days if the strength reduction is to be less than 10%.
The poor shelf life of pozzolona mixture is probably one reason why this approach
alternative cement has not succeeded.
The listed proportions indicate proportion by weight. It can be seen that the 28 days
strengths of most of the mortars are above the BIS codal requirement of 3.0 MPa.
It must be noted that bulk density of lime–burnt clay mixture is quite low and hence the
mortar proportions by volume are quite rich when compared to the usual cement mortar
proportions
This means that greater proportion of lime-pozzolona cement has to be used to achieve
satisfactory mortar strengths.
It is seen that when the burnt clay and rice husk are separately produced adequate rice
husk ash can be added to provide good strength.
When rice husk is used to burn the clay, the process become more economical but the
strengths are moderate. It must be noted that 6 months strengths are substantially high.
A clay rice-husk ratio of 1:0:6 is ideal from the point of view of strength and economy.
It can be seen that the Raichur fly ash is very fine and 30% of the particles are finer
than 2µ. The Neyveli ash is rather coarse and most of the particles are coarser than 25µ.
The characteristics of fly ash as pozzolona were studied using these two samples and
making lime pozzolona mortar cube of 5cm size.
The lime fly ash mixtures were ground in a ball mill and Accelerating additive like
plaster of Paris, gypsum was sometimes added.
The tests show that lime-fly-ash mortars are eminently suitable for construction with
the 180 day strengths in excess of 10.0MPa. Leaner mortars could be used because of
high strength of 1:3 cement-sand proportions.
The Raichur fly ash, with its fine particulars is exceedingly good as pozzolona while
Neyveli fly ash is very much inferior.
MATERIALS
Fibre reinforced cement composite is a two-phase material consisting of matrix which
is reinforced with randomly oriented small fibres to improve the mechanical properties of the
matrix
Matrix Material
The matrix generally consists of Portland cement, aggregate and admixtures and can be
any of the following.
a) Plain Portland cement
b) Cement with additive such as soil, fly ash or condensed silica fume.
c) Mortar containing cement and fine aggregate
d) Concrete containing cement, fine and coarse aggregate.
Water is added to the concrete mix for hydration of cement and for moulding of the concrete
to the desired shape. It is very well established that the compressive strength of the concrete
depends up on the water cement ratio in the mix.
W/c ratio of 0.28 is sufficient for the hydration process, to obtain a plastic workable
mixture, a minimum w/c ratio of 0.6 is needed. Addition of fibres to the concrete
reduces the workability. In order to keep the w/c ratio within reasonable limits of not
affecting the compressive strength but to still achieve workability, water reducing
admixtures have become an integral part of fibre reinforced composites.
In addition to water reducing admixtures, mineral admixtures like fly-ash and silica
fume are also added to the matrix.
Fly ash is used to improve workability, reduce the heat of hydration, economy and to
enhance permeability characteristics of the matrix.
Silica fume is added mainly to achieve high strength matrix.
Reinforcing Material
The reinforcement is in the form of short fibres of small diameter distributed throughout
the matrix.
The fibres can be broadly classified as:
1. Metallic fibres
2. Polymeric fibres
3. Mineral fibres
4. Natural fibres
By its very definition reinforcement is supposed to induce an increase in strength in the
reinforced material (i.e. matrix).
In order to be effective in concrete matrix, the fibres must have the following properties.
a. Tensile strength significantly higher than that of concrete
b. Bond strength with concrete matrix preferably of same order as or higher than the
tensile strength of matrix.
c. The elastic modulus in tension to be significantly higher than that of concrete.
d. The poison’s ratio and the coefficient of thermal expansion preferably be of the same
order as that of matrix.
Metallic Fibres
Metallic fibres are either made out of carbon steel or stainless steel. The tensile strength
ranges from 345MPa to 1380MPa. The modulus of elasticity is about 200GPa.
The fibres c/s may be circular, rectangular, crescent shaped or irregular. Most common
steel fibres are round in c/s with dia ranging from 0.4mm to 0.8mm and a a length
ranging from 25mm to 60mm.
Their aspect ratio is generally less than 100 with common range of 40 to 80.
The below figure shows some of the fibres types of different shapes used in practice.
a) Round and straight steel fibres
b) In order to the bond strength, the fibres have been indented.
c) Crimped
d) Hooked at the ends
e) Enlarged at the ends
f) Fibres are produced from wires that have been shaved down in the steel wool making
process and such fibres have a crescent shaped c/s.
g) Fibres have irregular surface with crescent shaped c/s.
Polymeric Fibres
Polymeric fibres are by products of petrochemical and textile industries. The fibres
types have been explored for use in cement based matrices are Acrylic, Aramid, Nylon,
Polyester, Polyethylene and Polypropylene. Even though these fibres have reasonably high
tensile strength, the modulus of elasticity of most of them is quite low (except aramid).
Fibres that contain at least 85% by weight of Acrylonitrile are classified as acrylic
fibres.
Nylon was one of the first of the polymer fibres to be included in cement based matrices.
When used in small volumes (<1% volume fraction of composite) it has been found to
reduce the flexural strength of the composite.
Compared with other polymeric fibres, Aramid fibres have higher tensile strength and
modulus of elasticity and hence they can enhance the mechanical properties like tensile
and bending strength of the composite.
The primary limitation for their use in concrete is high cost compared to other fibres.
Mineral Fibres
Glass fibres are the predominately used mineral fibre. Glass fibre is silica based glass
compounds that contain several metals oxides which can be tailored to manufacture different
types of glass
These fibres relatively high tensile strength and modulus of elasticity compared to
polymeric fibres.
Furthermore, they are quite economical and hence are the most commonly used fibres
for structural applications.
In the initial stages borosilicate glass fibres (E- glass) and soda-lime-silica glass fibres
(A-glass) were employed to reinforce cement-based composites.
Since both E-glass and A-glass fibres were found to lose their strength property in the
alkaline environment of cement based composites (pH ≥12.5), the need for alkali
resistant fibres resulted in the development of alkali resistant glass (AR glass)
Natural Fibres
Since in many parts of world manmade fibres like steel or polymer fibres are not
available, attempts have been made to incorporate naturally occurring fibres extracted from
plants in cement based composites.
A unique aspect of these fibres is the low energy needed for their extraction. A major
problem in the use of these fibres in cement/concrete matrix is that they disintegrate in
the alkaline environment and hence durability of the composite is a matter of concern.
Since these fibres are economical, attempts have made to overcome the problem of
durability either by use of admixtures in concrete to reduce its alkalinity or by
protecting fibres by some special treatment.
Some of the natural fibres used in Portland cement composite are akwara, bamboo,
coconut (coir), jute, sisal, sugarcane bagasse, wood and elephant gross. Even though
these fibres are sufficiently strong in tension, their modulus of elasticity is quite low.
Akwara fibre is extracted from a vegetable plant stem, which is grown in large
quantities in Nigeria. They are found to be durable in the alkaline environment and
dimensionally stable under alternate wetting and drying conditions.
Bamboo fibres have tendency to absorb water, which adversely affects the bonding
between fibre and the matrix during the curing stage.
Fibres extracted from the coconut are called as coir. Coir fibres are short in length and
are found to be sensitive to moisture change.
Sisal fibres are extracted from the leaves of Agave sisalana and it primarily consists of
hemicellulose, lignin and pectin. Sisal fibres even though relatively strong, are not
durable in alkaline environment.
Elephant grass fibres are extracted from elephant grass stems, which grows up to a
height of 3m. The stems are packed with tough sharp fibres bonded together with lignin.
Extraction of elephant grass fibres is difficult but they are stable under varying moisture
conditions and alkali resistant.
Wood fibres constitute a major portion of natural fibres used in concrete. These fibres
have high tensile strength and young’s modulus and process of extraction is very well
developed. The process of extracting fibres from wood is called pulping and the process
can be mechanical, chemical or semi-chemical.
Carbon Fibres
Carbon fibres are the most expensive of all the fibres discussed till now.This is due to
the increased cost of their manufacturing process as well as the increased cost of raw materials
required for their manufacture. Carbon fibres have high strength and modulus comparable to
that of steel fibres. They are relatively inert to alkaline environment and their specific gravity
is about 1.9. Hence they are used to make special products requiring high tensile and flexure
strengths and light in weight.
Current manufacturing technologies use polyacrylonitrile (PAN), rayon (regenerated
cellulose) and pitch as starting materials, PAN based carbon fibres have good properties
but are high in cost.
Pitch based carbon fibres are more economical but their mechanical properties are
poorer than PAN based carbon fibres but still higher than polymeric and neutral fibres.
PAN based carbon fibres have a modulus and tensile strength of 300GPa and 5200MPa
respectively; whereas pitch based carbon fibres have a modulus and strength of 160GPa
and 1400GPa respectively.
MATERIALS
The fibre-reinforced polymer composite is a two-phase material consisting of
polymer matrix reinforced with small diameter fibres which are either continuous or
discontinuous and oriented uni-directionally or randomly
MATRIX MATERIALS
The matrix in a composite performs the following functions;
a) It glues the bundles of fibres together and helps in distributing the external load to
all the fibres,
b) It protects the fibres from adverse environmental effects and prevents the buckling
of fibres under compressive forces, and
c) It protects the fibres from mechanical abrasion.
Polymers, also called as Resins are employed as matrix material in FRP composites.
The polymers are classified into two types.
1) Thermo-set polymers
2) Thermoplastic polymers
Polymers (in Greek: poly+meros meaning many parts) are large organic
compounds formed by the joining together of many small molecules to form a large
molecule by a process called as polymerization. The simple compounds from which
polymers are made are called as monomers.
Both thermo-set and thermoplastic polymers are long chained molecules. The
polymers in which their long molecular chains are interconnected with chemical bonds or
cross links forming a rigid three-dimensional structures are called as thermo-set polymers.
In the case of thermoplastic polymers their long molecular chains are not
chemically interconnected and are held in place by weak secondary bonds like
Vander Walls bonds.
Thermo-sets are generally liquid resins, which are heat activated (or cured) to
achieve cross-linking of the molecular chains.
Thermoplastics are solids, which have to be melted by heating, moulded to the
desired shape and cooled. Because of their differing chemical structure, the thermo-
sets and thermoplastics have unique properties.
Thermo-sets are more rigid than thermoplastics due to their cross linked chemical
structure and cannot be re melted by heating, whereas thermoplastics can be re
melted by heating.
Thermo-set polymers have good thermal stability and chemical resistance. They
also exhibit reduced creep and stress relaxation compared to thermoplastics.
Thermo-sets have short shelf life after mixing with curing agents (catalysts) and
low strain to failure and impact strength.
Thermoplastic polymers on the other hand have high impact strength, fracture
resistance and strain to failure.
The below figure shows the schematic representation of thermoplastic and
thermosetting polymers.
POLYESTER RESINS
These are formed by condensation polymerization of a diacid with dialcohol. By
the elimination of water between the acids and alcohols, ester linkages are formed. The
resulting molecular chain of alternate acid and alcohol molecules is collectively called
polyester resin. The cross-linking occurs by the addition polymerization reaction. A
molecule that readily produces free radicals initiates the cross-linking reaction. Polyester
resins are the cheapest resins suitable for making FRP composites for civil engineering
applications.
Styrene (reactive diluents) is added to the resulting polymeric liquids to reduce its
viscosity.
The Orthophthalic resins have low thermal stability and chemical resistance,
whereas the Isophthalic resins have better chemical and thermal resistance.
The properties of polyester resins depend strongly on the cross-link density like for
example increasing the density of cross-links, improve the elastic modulus, glass
transition temperature and thermal stability but reduces the strain at failure and
impact energy.
EPOXY RESINS
These resins are generally manufactured by reacting epichlorohydrin with
bisphenol A. Varying the proportions of the two reactants forms different resins. Epoxies
possess many desirable properties like excellent adhesion, strength, low shrinkage,
corrosion protection and processing versatility. These resins are expensive compared to
polyesters.
REINFORCING FIBRES
Reinforcements in the form of fibres, particles or whiskers are used with resin
systems to improve the mechanical properties of the resins and to produce usable products.
By far the most important fibre used with polyester and epoxy resins is glass fibre which
is available in a variety of forms like rovings, woven rovings, cloths and random chopped
fibre mats.
In recent years high strength carbon fibres and polyaramid fibres have found
increasing use in the manufacture of composite materials for a variety of applications.
Natural fibres such as jute and sisal have also been used to reinforce thermosetting resins.
APPLICATIONS
FRP composites have found application in various branches of engineering and
technology. During the initial years it was predominantly used in aerospace structures due
to its light weight and high strength where cost was not the governing factor. With the
passage of time its application spread to other areas of engineering. Due to its corrosion
resistant property it is used in chemical industries. It is also used in making sports
equipment like tennis racket, fishing and pole-vaulting rods and baseball bats. It is also
used in bio medical engineering for making prosthesis. Pultruded FRP rods have been used
as reinforcement in concrete. FRP sheets have also been used for repair and retrofit of
concrete structures. FRP composites will find newer applications in future in all spheres of
life
The other agro wastes have not been used traditionally in building construction but they all
have potential uses as follows
For instance, experiments have been made by making rice husk-phenol
formaldehyde boards. Such boards could be used as replacement for plywood
panels. This is more environment friendly than plywood since use of plywood
implies considerable deforestation.
Rice husk ash, when rice husk is burnt under controlled conditions, results in
amorphous silica with excellent pozzolona properties.
Coir and sisal fibres have been attempted in fibre cement composites, but their
durability characteristics are not well known. However, using coir and sisal fibre
along with polyester resin as a matrix appears to offer a cheaper, energy efficient
alternative to glass fibre reinforced polyester composites. The properties of such
composites are yet to be fully explored.
Bamboo, cane and lantana are other biomass resources with potential in building
construction. Among these, use of bamboo in building construction is well known.
It has been used extensively for housing is North East regions of India. Its use in
wattle and daub walls is well known in Mysore and Shimoga districts.
Use of cane for furniture is well known. The long rounded cane lengths could be
considered for use as tension members in a truss. Joining details for such use need
to be worked out.
Lantana has also been attempted as a substitute for cane. Since lantana is a weed,
it could be an ideal resource for construction. It appears to have termite resistant
properties and this may have considerable advantage. Its termite resistance,
however, needs to be conclusively proven. Woven mats of lantana can be used as
reinforcement for wattle and daub walls or partition boards.
INDUSTRIAL WASTES:
A large number of industries produce waste materials which need to be either disposed of
or utilized for some purpose. Very often, disposal of wastes could pose problems. There
are instances where large chunks of land are rendered useless or unavailable due to
deposition of such wastes. Fly ash and marble dust are two typical wastes which can pose
serious disposal problems.
Some of the typical industrial wastes may be listed as under:
1) Fly ash from thermal power stations.
2) Blast furnace slag from steel plants.
3) Mine wastes from iron ore mines.
4) Tailings from copper mines.
5) Fine rock dust from gold mines.
6) Granite polishing wastes.
7) Marble polishing wastes.
8) Rock dust from stone crushers.
9) Red mud from Aluminium factories.
10) Brick, Mortar and Concrete wastes from demolished buildings.
Marble dust can also be used for lime and Hydraulic lime manufacture. The marble
dust may be converted to ball like aggregates by mixing boiled starch. Such
aggregates can then be burnt in a lime kiln to produce quick lime.
If the marble dust is mixed with clay and then made into balls, the balls can be used
to make Hydraulic lime.
MODULE – 4
ALTENATIVE BUILDING TECHNOLOGIES
EFFICIENT FOUNDATIONS
The Use of stones (size stone or random rubble) is quite common in south India for
foundation of walls. The modern practices of using cement mortar makes the foundation rather
expensive traditionally, two storeyed buildings have been built on stone-in mud mortar
foundation. The stress level in the foundation is generally so low that even mud mortars should
suffice. Use of soil - cement as mortar or soil-lime-cement as mortars should prove to be a cost-
effective alternative. Use of arched foundations is also a cost-effective alternative.
It is also possible to use reinforced masonry for wall construction. The reinforcement will
vastly enhance the lateral load carrying capacity of the wall. Use of reinforcement bands
along the horizontal joints is a convenient way of reinforcing masonry.
Two types of in-situ walls may be mentioned:
1) Cast-in-situ RC walls.
2) Rammed Earth Walls.
The Rammed Earth could use either plain earth or stabilized earth
CONSTRUCTION TECHNIQUES:
Masonry Bonding
A large variety of bonding techniques may be considered in masonry construction.
In conventional brick masonry, English bond and Flemish bond are well known. English
bond is the most common mode of construction in India. When blocks are not proportioned
in the way in which burnt brick is, these bonds are no longer feasible.
For instance, when hollow-concrete blocks of size 40 cms x 20 cms x 20 cms are used, the
blocks have to be kept in ‘Stretcher bond’ leading to a wall thickness of 20 cms and a course
height of 20 cms as shown in Figure below
The concept of rat-trap bond was popularized by Laurie Baker in Kerala in the seventies.
This involves keeping bricks on edge creating a gap in the thickness of the wall.
About 25% of the bricks can be saved by this process.
Many practitioners hold the view that rat trap bonding does not lead to a loss of strength
and one can build such walls of 22.5 cm thickness up to four storeys!
At present, when 3.5MPa bricks are used, such walls can certainly be used for single storey
construction.
Figure 7.3 shows a typical view.
Composite Masonry:
It is sometimes useful to build walls of two different materials.
The materials selected may be stone-cum-brick, stone-cum-SMB, burnt brick-cum-un
burnt brick and so on.
This can lead to using a very durable material on the external face and a material of
moderate durability in the interior.
Very often such methods are useful in cost reduction and reduction in wall thickness.
Fig. 7.4 shows a typical way of combining stone and brick in building a composite wall of
29cms thickness.
It is also important to note that the two layers of different materials need to be bonded by
periodic use of ‘through stones’.
The strength of such walls may be assessed on the basis of the strength of the stronger
material (also thicker layer) ignoring the strength of the weaker material.
Cavity Walls:
Such walls are common in Western countries to improve the thermal insulation of the walls.
In countries like India, such concepts may be used in very hot regions to prevent penetration
of solar heat through walls.
However, it must be observed that the overall wall thickness may have to go up to more
than 40cms if these techniques are to be effective.
Fig. 7.5 shows a typical brick wall with a 7cms cavity.
It is important to use bond blocks to bond the two layers. These bond blocks could be made
of concrete with strength of at least 5.0 MPa to obviate separation of the veneer through
shearing of bond blocks.
The cavity can also be filled with brick bats or coal cinder to improve the insulation. It may
be pointed out that walls of such higher thickness are necessary only for external walls
facing East and West and all the other walls may be of 23 cms thickness
Rammed Earth
This is a technique of in-situ wall construction wherein either plain earth or stabilized earth
is compacted in layers between two plates.
Fig. 7.6 shows typical sketch of a simple rammed earth mould.
A dry density of about 1.85 gm/cc has to be achieved for good performance of rammed
earth walls.
Figure 7.7 shows a typical wall construction in progress using the rammed earth
technique.
Typical rammers used for this purpose are shown in Figure 7.8.
MATERIALS:
The materials used for Ferro-cement are
Cement
Sand
Wire Mesh
Steel Bars
In addition to the above, high tensile steel wires are also used for pre-stressed Ferro-cement.
Cement:
Ordinary Portland cement that is commercially available in the market is satisfactory
for Ferro-cement construction. However, other types of Portland cement can be used
like sulphate resisting cement for Ferro-cement construction in marine environment.
Portland pozzolana cement has also been recommended for Ferro-cement as it provides
good resistance to sulphate attack and also competitive in price compared with ordinary
Portland cement.
Rice husk ash (up to 20% by weight) can be used as pozzolana and mixed with Portland
cement without any deleterious effects on the mortar.
Sand
Well-graded natural river sand with particle size less than 4.75 mm having fineness
modulus between 2.5-3.0 is suited for Ferro-cement construction.
As cover to reinforcing mesh is small and does not exceed 2-3 mm, the cement mortar
covering the mesh wires has to be dense to prevent corrosion of reinforcement.
Hence grading of sand for mortar mixes becomes very important to get workable
cement mortar with low water-cement ratio.
The water used for preparing cement-sand mortar should be potable and relatively free
from organic compounds.
The proportion of cement-sand mix generally varies from 1:1.5 to 1:3 and water-cement
ratio varies from 0.35 to 0.55.
Wire Mesh:
One of the important constituents of Ferro-cement is wire mesh reinforcement.
These generally consist of thin wires, (galvanized or un - galvanized) either woven or
welded at their intersections.
The mechanical properties of Ferro-cement depend on the type, quantity, orientation
and strength properties of the mesh reinforcement.
Different types of mesh reinforcement are available in the market, which are suitable
of Ferro cement construction. Some of them are listed below
Hexagonal wire mesh: also commonly known as chicken wire mesh is fabricated from cold
drawn wires of diameter varying from 22 - 26 gauge and woven into hexagonal patterns with
mesh opening varying from 10 mm to 25 mm. This is the cheapest, easiest to handle and most
commonly used in Ferro-cement construction.
Woven wire mesh: is fabricated by simply weaving the galvanized wires into desired grid
sizes without welding them at the intersections. The grids are generally square. The mesh wires
are not perfectly straight and some amount of waviness exists.
Welded wire mesh: is fabricated in rectangular or square pattern by perpendicular intersecting
wires (generally 2-3 mm diameter) made of low to medium tensile strength steel (which are
much stiffer than hexagonal or woven wire mesh) and welded together at the intersections.
Expanded metal mesh, which is sometimes used in Ferro- cement construction, is formed by
slitting thin gauge sheets and expanding them in a direction perpendicular to the slits to produce
diamond shape openings. This mesh has inherent advantages like good mechanical bond and
ease of placing.
Skeletal Steel
As the name implies this is generally used for making framework of the structural
component upon which layers of wire mesh reinforcement are laid and also serve as spacer
to wire mesh.
The steel rods are provided in both longitudinal and transverse directions.
When they are provided for non-structural purpose, they are spaced as widely as possible
and when provided for carrying external loads, their spacing is governed by design
considerations.
In general, mild steel rods or galvanized iron wires of diameters varying from 2 mm to 6
mm are used.
Sometimes for structural purpose high yield strength deformed bars are also employed.
Admixtures
Admixtures are additives, which are introduced in the cement sand mortar mix to modify
some of the properties of the mortar in its fresh and hardened states.
These materials may be chemical admixtures in which case they are added in quantities no
larger than 5% by weight of cement or other materials in which case they are added in
excess of 5% by weight of cement and referred as additives.
Different types of admixtures are used to improve/modify various properties and some
important ones used in Ferro-cement are briefly discussed here.
Retarders
A delay in the setting time of cement paste is achieved by the addition of a retarding
admixture and thereby helping in reducing the generation of heat.
Retarding action is exhibited by sugar, carbohydrate derivatives and some other salts.
Water reducers:
These admixtures also called as plasticizers help to improve the plasticity of the mix in its
fresh state and are mainly used to achieve higher strengths by reducing water-cement ratio
or for improving workability to facilitate proper compaction of cement-mortar.
In addition to the above admixtures, Ferro-cement may require chemical additives to reduce
the reaction between matrix (alkaline environment in cement-mortar) and galvanized
reinforcement, which produce hydrogen gas. As the gas is formed on the wires, they
deleteriously affect the bond strength.
Chromium trioxide added to the mixing water has been reported to be useful in reducing
this problem.
Foamed blast furnace slag has been used as a lightweight aggregate for partial or full
replacement of sand, which results in reduction of density and thermal conductivity of
Ferro-cement.
Both these properties are desirable, when Ferro-cement elements are used for roofing and
wall panels.
Use of fly ash as partial replacement of cement can help in improving durability of Ferro-
cement and at the same time reduce the cost.
CONSTRUCTION METHODS:
Ferro-cement construction does not require skilled labour nor heavy capital investment on
equipment to produce them.
There are four major steps in Ferro-cement construction
1. Placing of reinforcement
2. Mixing of mortar
3. Placing mortar
4. Curing
As the reinforcement content in Ferro-cement is very high (up to 8% by volume) and is
uniformly distributed throughout the thickness of the element, the essential requirement is
that the continuous mesh reinforcement has to be completely impregnated and covered with
cement mortar.
Basically to achieve this goal one may either force the cement mortar into the pre-existing
skeletal steel framework or alternatively force layers of mesh reinforcement into a bed of
mortar.
A number of techniques are being used for placing the mortar into the framework of mesh.
Among these are hand plastering of mortar from one side against a mould or from both
sides.
During this process care must be taken to ensure full penetration of mortar and elimination
of voids within the thickness of the panel.
Hand vibrators may be adopted when available, while casting-using mould.
Moulds of metal, wood or masonry are made to suit the shape of the Ferro-cement
component.
One-stage technique
Consists of single application of mortar from outside to inside of mesh and subsequently
finishing it off to a smooth surface before initial set takes place.
Two-stage technique
In this process mortar is plastered from one side without fully penetrating through all the
mesh layers and the outer surface is finished smooth and cured. Later the remaining portion
is plastered with mortar.
To assist in bond between the old and new mortar, cement grout is applied before second
stage plastering is carried out on the old mortar. This technique is adopted when more than
five layers of mesh is used.
Sectional plastering
While undertaking plastering of large Ferro-cement structures, it may be preferable to
plaster in sections using one-stage technique, necessitating the need for construction joints.
The disadvantage of this method is the difficulty in obtaining a smooth construction joint
due to differential shrinkage of mortar layers of different ages.
Apart from the above mentioned manual methods for manufacture of Ferro-cement, some
mechanized methods have also been developed viz.
1. Shotcreting or gunite plastering, where in mortar is applied pneumatically by spraying on
to the skeletal steel frame work by means of compressed air
2. Centrifuging for casting cylindrical units
3. Vibro-pressing for compaction. All these mechanized methods; are useful for large-scale
production of quality Ferro-cement components,' but require skilled technicians and
considerable capital investment for machinery/equipment.
DURABILITY
The performance of Ferro-cement structures depends to a great extent on its durability
against the environment that it is exposed.
Even though measures needed to ensure durability of conventional reinforced concrete
are also applicable to Ferro cement, there are three other factors affecting its durability,
which are unique to Ferro cement.
There are three other factors affecting its durability which are unique to Ferro-cement.
1) The cover to reinforcement in Ferrocement is very low and hence it is relatively easy
for corrosive liquids to reach it.
2) The surface area of reinforcement is high and so the area of contact over which reaction
takes place and the resulting rate of corrosion are quite high.
Due to the use of galvanized reinforcement, the zinc coating can react with the alkalis
(calcium hydroxide) present in the fresh cement mortar leading to formation of calcium
zincate and hydrogen gas.
The release of hydrogen gas on the surface of reinforcement can deleteriously affect the
bond between the cement mortar and reinforcement.
It has been reported that addition of about 100 ppm of chromium trioxide to mixing
water inhibits the formation of hydrogen.
A more serious difficulty is the galvanic corrosion, which can take place when
galvanized steel (mesh) and ordinary steel (skeletal steel) are in contact via the
electrolytic solutions present in the mortar.
The reinforcement is protected from corrosion by the mortar cover, which may get
damaged by external or internal causes.
The external causes may be physical, chemical or mechanical like weathering, abrasion
and attack by natural and industrial liquids and gases.
The extent of damage caused by these agents depends on the quality of the mortar, even
though under extreme conditions any unprotected mortar is bound to deteriorate.
The internal causes are alkali-aggregate reaction and permeability of mortar.
Permeability of Ferrocement is of significance particularly with regards to water
tightness of liquid retaining structures.
Further permeability of mortar in precast units for housing like roof, floor and wall
elements can cause penetration of humidity resulting in corrosion of reinforcement.
In Ferrocement marine structures due to thin cover of mortar the danger of corrosion of
reinforcement is quite high.
To protect the reinforcement from corrosion, coatings of vinyl or epoxy types can be
provided.
The coatings should have the following characteristics:
1) Good adhesion to mortar,
2) Tolerant to alkalinity in ferrocement,
3) Good abrasion and chemical resistance,
MECHANICAL PROPERTIES:
Ferro-cement derives its unique properties due to the subdivision and distribution of the
reinforcement which can be described with the two parameters namely volume fraction of
reinforcement defined as volume of reinforcement per unit volume of Ferrocement and
specific surface of reinforcement defined as surface area of reinforcement per unit volume
of Ferrocement.
Within the elastic range Ferrocement can be considered as a homogeneous material and its
elastic properties can be obtained from the elastic properties and volume fractions of its
constituents.
Behaviour in Tension.
Within the elastic range the total load (Pt) carried by the Ferro cement element is shared
between the reinforcement carrying a
Behaviour in Flexure:
Ferro cement elements being thin walled, they derive their strength and stiffness due to the
shape and form of the element.
The analysis of Ferro-cement elements in bending can be performed using the conventional
reinforced concrete theory.
It is assumed that the cross-sections of the element, which are plane and normal to neutral
axis before bending, will remain plane and normal to the deformed neutral axis.
If the skeletal steel is provided very close or at the centroid of the cross-section, practically
it will have no contribution in bending and hence can be neglected within the elastic range.
The cracking behaviour like number of cracks and their widths depends of the specific
surface of the mesh reinforcement in the longitudinal direction.
If skeletal steel is provided for structural purpose, they will be located close to the tension
face of the element and their contribution to the flexural strength needs to be accounted.
Typical design calculations for a Ferro cement roof element having an open cylindrical
cross-section
APPLICATIONS:
Ferro-cement applications can be broadly classified into two types
1. Marine applications
2. Terrestrial applications
The early applications of Ferro-cement have been more to the building of boats and yachts.
In recent years Ferro-cement has received attention as a material for terrestrial uses in
housing, agriculture, water and grain storage structures, irrigation, water supply, biogas
digesters and as permanent forms for reinforced concrete construction.
Ferro-cement is well suited for prefabricated housing components like wall elements,
floor/roofing units, trusses, tiles, lintel and chejja.
Roof/ floor elements of various cross-sectional shapes like trapezoidal, V-shaped,
cylindrical, corrugated, channel catenary and cored slab have been developed.
In order to use them over longer spans, they could be pre-stressed (Pre-tensioning/Post-
tensioning) so that deflection can be controlled to within permissible limits,
The choice of a roofing system will thus also mean a choice of specific type of roof and the
class of technologies available under the type. There are more ways of classifying roofs
based on other parameters.
For instance, following classifications are also relevant to the design and construction
environment available at a site.
The Approach to Cost Optimization
Generally designers would like to minimize the cost for a specific performance
requirement.
It is necessary to look at the roof as a system while attempting to carry out a cost
optimization.
Roof as a Static Structural System
The cost of a roof structure depends on three factors,
1) Loads acting on the roof,
2) Efficiency of the structural system
3) Material used for the structure.
The cost and the performance may be optimized by reducing roof loads and spans.
Improving the efficiency of the roof structure and by selecting cost-effective materials.
All these steps can be taken simultaneously leading to significant cost reduction.
As a typical illustration of the optimization of a roof element, Table 11.2 shows the cost of
a rafter for a tiled roof building of span 3 meters.
Roof Structure + Covering
In this class of roofs, the cost reduction may be achieved by three techniques:
1) Reduce weight of covering
2) Use more efficient structure
3) Increase size of covering unit.
A combination of all the three techniques may be used.
For instance, one can replace the Mangalore tile by a locally produced micro-concrete tile,
which could be larger in size.
This will increase reaper spacing and reduce the number of joints.
Integral Roofing
All the proposed alternatives need to be discussed in relation to reinforced concrete with
reference to cost and performance comparisons. The reinforced concrete slab has two basic
inefficiencies. Firstly, a typical 12.5 cms slab weighs 300 kgs per sq. metre. This has to be
designed for a live load of 200 kg. per sq. metre. This means, for a design load of 500
kg/m2, self-weight is 60%. In other words the structural efficiency of the R.C. slab is only
40%.
Secondly, the concrete in the tension zone hardly takes any stress although it is quite
expensive. Thus, an alternative to the normal R.C. slab is a beam and slab roofing which
has a reduced slab thickness. In general, this saves steel and concrete by using the materials
more efficiently.
The typical stress distribution in the R.C. slab and the beam and slab system.
The increased efficiency of this beam and slab system, however, poses a new problem.
The heat transfer through a thinner roof slab can increase the thermal discomfort in the
space below.
Additional features to alleviate this are needed.
A hollow element in the slab portion with good gross thickness of more than 15cms leads
to better thermal comfort.
Sometimes it is possible to use the beam and slab concept in composite constructions using
different materials for the beam and the panel.
Such systems where the beam and the panels are structurally integrated may be known as
the composite T-beam roof.
In this case the beam may be of built-up steel or R.C. or timber while the panel may be of
concrete, brick work or stone.
A large variety of local variations of such systems can be thought of. Fig. 11.2 shows a
typical example.
The filler slab is another concept, which has been in use in this country for more than 50
years.
Here, part of the concrete in the tension zone of a R.C. slab roof is replaced by a cheaper,
possibly lighter alternative.
In a recent construction example, about 23% of the concrete could be replaced by mud
blocks (the cost of mud block being one third of the cost of concrete for the same volume).
Brick masonry vaulting is another concept of an integral roof. Such roofs require very little
steel and can provide good performance over a long period of time.
Brick vaulted roofs spanning up to 10 metres have performed well for several centuries in
South India.
It is also possible to use alternative building blocks like concrete blocks or stabilized mud
blocks for such masonry. Spherical domes using brick masonry are again equally feasible
where the plan area to be covered is circular or square.
The hyperbolic paraboloid shell roof using thin reinforced concrete is another option for an
integral roof.
This is suited only for single storeyed buildings.
The shape of the roof leads to a great economy in the use of cement and steel.
This can be constructed using fairly simple formwork consisting of casuarina poles and
mud cantering.
Fig. shows a typical rectangular room with a twin “hypar” shell roof. Such thin roofs may
indeed show problems of thermal comfort in the interior.
Size and shape of the filler material are governed by the factors like slab thickness, code
guidelines on spacing of reinforcement bars, desired ceiling finish, etc and has to be
carefully selected.
Typical sizes of the filler materials are given in below Table
Quantity of concrete in the tension zone of the slab that can be replaced by a filler material
depends upon the shape of the filler material available and the thickness of the solid slab.
For example, in a solid concrete slab of 125mm thickness, a filler block of 60- 70mm
thickness can be easily accommodated.
In a typical situation by using a stabilized mud block, 25% of the concrete can be replaced
by a material, which costs l/'3rd of the cost of concrete.
This means that 15%—20% of the cost of concrete can be saved by this operation.
In general, the SMB used as filler will have a higher percentage of cement (-8%) to ensure
a high level of performance under wet conditions as well.
prefabricated, and assembled into a roofing system with minimal formwork without the use
of heavy equipment.
It is expected that such roofs are lighter and structurally more efficient when compared to
solid reinforced concrete slab roofs/floors.
Shear
connector Precast
panel
Precast
beam
Shear Curved
connectors panel
Precast
beam
Since the panels and beams are cast separately and then assembled, there should be proper
shear connection between them to achieve composite action for the system to behave as an
integral structural unit.
The flexibility of composite beam and panel roofs arises out of the fact that the materials
for the beams and the panels could be of two different materials, and the composite action
between them could be achieved by proper shear connectors.
In the absence of shear connection, the panels will simply sit on the beam and the roofing
system will be structurally inefficient.
Table 11.4 gives the typical list of materials/technologies for the beams and panels.
Various combinations of beams and panels could lead to different types of composite beam
and panel roofing systems.
Figs. show sketches of some possible geometric configurations for the beams and the
panels.
Shear
connector
Shear
connector
In some situations especially for larger roof spans where the beam size is large, it may be
difficult to handle the beam manually while assembling the roofing system.
In such situations one can resort to in-situ casting of the beams.
Since the concept is aimed at optimising the sizes of beam and panel elements it is
preferable to keep the panel sizes small such that the weight of each panel is within 50kg.
This will facilitate handling of the panels manually thus avoiding need for any heavy
hoisting equipment.
Panels
Based on the geometrical shape, the panels could be of two types, curved cross-section or
flat panels.
Different types of panels and the material used for the panels
Wooden template will ensure the thickness and size of the panel precisely.
In case of brickwork or tile-work panels, the bricks/tiles are arranged as shown in Fig.
11.28, place the reinforcement in the joints and then pack the joints with mortar.
The following mentioned precautions or measures have to be exercised while casting the
panels.
a) Spread a sheet of thin paper on top of the mould and then place the wooden template
over that. This will facilitate easy removal of the panel from the mould
b) In case of tile-work or brickwork panels smear the side faces of the bricks/tiles with a
fresh cement slurry (1 cement: 1 water) just before placing them into the wooden
template. This coating will enhance the bond between the brick/tile and the mortar
grout.
c) Do not hold the shear connectors while lifting and handling the panels. This will avoid
disturbing the shear connector which can impair the shear connection and the composite
action
d) The panels after casting should not be disturbed far at least 24 hours. The panels after
removing from the mould can be stacked on edge separately and continue curing in the
stack. Concrete panels have to be cured for 4 weeks while the brickwork or tile-work
panels should be cured for at least 7 days
Casting of Beams:
In a composite beam and panel roof system partially cast beams are used.
The beam will be complete after integration of the panels with the beam through shear
connectors.
Different types of possible beam configurations are shown in Figs. 11.16 to 11.18.
Shear
connector
Shear
connector
Fig. 11.29 shows the mould and partially cast beams in a casting yard.
Fig. 11.30 shows the assembling of composite beam and panel roofing system.
Figs. 11.31 to 11.33 show some typical ceiling finishes and external appearance of different
types of composite beam and panel roofs.
The Engineering practice in England in the nineteenth century was perhaps totally
unfamiliar with brick vaulting.
The analysis of shell structures was practically unknown while the technological
practice in India was nearly 150 years ahead of the European Science of shell analysis.
The practice of vault building must have died out to lack of patronage, alternatives
using wood and steel and lack of support by matching developments in Engineering
Science.
The construction of domes has always paralleled closely the developments in vaults.
The dome had the added advantage that it could often be built without formwork.
The dome at Bijapur is perhaps one of the finest examples of Indian dome construction.
One could perhaps argue that the dome never died in the Indian context.
There have always been situations where domes were needed architecturally and have
been produced in British India as well as independent India.
The brick can be positioned precisely using this radial rod/wire. The brick may be secured
temporarily to the mortar below by suspending weights hooked onto the brick. The brick laying
can now proceed horizontally till one circle is completed. Repeating this dome can be
completed.
The formwork is lowered after 24 hours and moved laterally to extend the previous
day’s work.
Construction of
masonry vaults
(using moving steel mould)
Construction of
masonry vaults
(using steel templates)
The vault construction proceeds in this manner till the other end is reached.
A variation of the moving formwork was attempted by having two arch shaped templates
kept parallel to each other with a distance of about 17cms separating the two. The template
had the facility of the two ends having small hinged portions. By rotating the hinged
portion, the span could be reduced and the template can be brought down.
In this system a portion of the vault is built using the two templates as support. The inner
template is then removed and placed in front of the outer template to continue the vault.
In this construction mode the vault is always supported on a gable wall at one end on a
template at other
MIVAN TECHNOLOGY
Mivan is an aluminium formwork system developed by a European construction
company. In 1990, the Mivan Company Ltd. from Malaysia started manufacturing these
formwork systems. Today, more than 30,000sqm of formwork from Mivan Co. Ltd. is used
across the world. There are a number of buildings in Mumbai that are being constructed with
the help of the Mivan system, that has proven economical as well as satisfactory for the overall
Indian construction environment. One of the architectural examples is XRBIA which uses
MIVAN system to achieve its dream of “A House for Every Indian”
The technology has been used extensively in Europe, Gulf Countries, Asia and other parts of
the world. Mivan technology is suitable for constructing large number of houses in a short span
of time using room size forms to construct walls and slabs in one continuous pour on concrete.
In this system of formwork construction, cast–in–situ concrete wall and floor slabs cast
monolithic provides the structural system in one continuous pour. To facilitate fast
construction, early removal of forms can be achieved by hot air curing / curing compounds.
Large room sized forms for walls and floor slabs are erected at site. These strong and sturdy
forms are fabricated with accuracy and are easy to handle. The concrete is produced in RMC
batching plants under strict quality control and convey it to site with transit mixers.
The frames for windows, doors and ducts for services are placed in the form before concreting.
Staircase flights, façade panels, chajjas and jails etc. and other pre-fabricated items are also
integrated into the structure. This proves to be a major advantage as compared to other modern
construction techniques. High quality Mivan Formwork panels ensure consistency of
dimensions. On the removal of the formwork mould a high quality concrete finish is produced
to accurate tolerances and verticality. The high tolerance of the finish means that, no further
plastering is required.
Advantages:
Mivan formwork requires relatively less labour
More seismic resistance
Increased durability
Lesser number of joints and reduced leakages
Higher carpet area
Smooth finishing of wall and slab
Uniform quality of construction
Negligible maintenance
Faster completion
Limitations:
Even though there are so many advantages of Mivan formwork the limitations cannot be
ignored. However the limitations do not pose any serious problems. They are as follows: –
Because of few small sizes finishing lines are seen on the concrete surfaces
Services after completing become slightly difficult due to the small width of components
It requires uniform planning as well as uniform elevations to be cost effective
The formwork requires number of spacer, wall ties etc. which are placed @ 2ft c/c; these
produce problems such as seepage, leakages during monsoon
Due to box-type construction, contraction cracks are likely to appear
Heat of hydration is high due to shear walls
It is rigid in design once placed, as any alteration becomes tough later
Remedial Measures:
It is possible to minimize contraction cracks by providing control strips in the structure which
could be concreted with a delay of about 3-7 days after major concreting. The problem of
cracking can be avoided by minimizing the heat of hydration by using flash.
Introduction
Conventionally building having basements are usually built by bottom-up method. In simple
words, stage of construction is from bottom of sub-structure to top of superstructure. Gigantic
civil engineering projects usually have constraints of time and working space. So we have to
follow the reverse of this conventional procedure. We call it “Top Down construction method”
which means we go from top to bottom.
1. Distance between boundary wall of existing building and building to be constructed is too
close and possibility of soil collapse is too high.
4. This method is usually preferred for tall buildings with deep basements, underground car
parks, underpasses and metro railway projects.
Advantages
2. This method enables above ground construction work to be carried out simultaneously with
excavation of basement thus resulting in saving of time and resources.
4. It offers dramatic Capital cost improvements while providing excellence of finish to the
build, enhancing and reducing resource usage, improving cost and reducing pollution.
Structural Requirements
Columns with sufficient capacity has to be pre-founded in bored piles to sustain the
construction load and to utilize as part of bracing system.- Pre-fabricated steel columns called
Stanchions are used as these columns.
Excavation for basement must be carried out with the support of permanent retaining wall so
that basement floor slabs can be utilized as lateral bracing-Diaphragm wall of 600mm to
1200mm in thickness with sufficient embedment in firm soil layers is commonly used as a
retaining wall. The wall is constructed panel by panel in full depth.Panel width varies from
2.5m to about 6m. Short widths of 2.5m are selected in less stable soils, under very high
surcharge or for very deep walls.
Procedure
1. Piles are drilled into the ground level to the bearing stratum using conventional drilled shaft
or slurry trench techniques. Shafts made are concreted up to the lowermost basement level to
form foundation piers.
2. Structural steel columns are installed in the open shafts to rise from foundation pier to the
ground floor level.
3. First level of excavation for ground floor slab is done. Ground floor slab is cast either above
the unexcavated soil or on drop down form system anchored to columns if the soil is excavated.
Ground floor slab is anchored with the diaphragm walls with the dowel/coupler bars which are
initially left at the time of casting of diaphragm walls.
Ground floor slab is cast and cured. Ground floor acts as a lateral bracing for the perimeter
walls.
It is to be noted that access openings are left in the ground floor slab for vertical soil removal
and for supply of equipment’s , manpower and other construction materials required for
construction.
4. Next lower level basement slab is poured which acts as a subsequent lower level lateral
bracing for diaphragm walls.
5. This process is repeated down up to the required levels.Each floor acts as a permanent plan
bracing for perimeter walls eliminating the need for temporary bracing to retain diaphragm
walls.Excavation is repeated until completion of entire basement.
6. Cast the basement wall and encase the steel stanchion to become permanent columns using
form work and reinforced concrete.Basement walls and steel stanchion are encased with
additional reinforcement to become permanent columns.
Advantages
1. It allows early restoration of the ground surface above the tunnel The temporary
support of excavation walls are used as the permanent structural walls
2. The structural slabs will act as internal bracing for the support of excavation thus
reducing the amount of tie backs required It requires somewhat less width for the
construction area
3. Easier construction of roof since it can be cast on prepared grade rather than using
bottom forms
4. It may result in shorter construction duration by overlapping construction activities
Disadvantages
1. Inability to install external waterproofing.
2. More complicated connections for the roof, floor and base slabs.
3. Potential water leakage at the joints between the slabs and the walls
4. Risks that the exterior walls (or center columns) will exceed specified installation
tolerances and extend within the neat line of the interior space.
5. Access to the excavation is limited to the portals or through shafts through the roof.
6. Limited spaces for excavation and construction of the bottom slab.
MODULE – 5
EQUIPMENT FOR PRODUCTION OF ALTERNATIVE MATERIALS
EQUIPMENT FOR PRODUCTION OF ALTERNATIVE MATERIALS
Machines for production of stabilized blocks: Mardini Machine
c) Cast 1:2 cement mortar in the gap b/n two channels, consolidate it and water cure the
portion for 7-10 days.
Method :
a) Prepare wooden or steel shuttering , and apply waste oil on the surface for easy de-
shuttering.
b) Place the reinforcement with the clear cover os 15mm from the surface of shuttering.
c) Prepare a dry mix of 1:2:4 cement, corse sand and 20mm down stone chips. Add water
at the rate of 25litres per bag of cement. Do the mixing thoroughly so that it is
homogeneous and ready for use.
d) Place pairs of Mangalore tiles and pour concrete in the horizontal spaces b/n the tiles
as well as on top. Overall thickness of the slab should be 100mm. Use hand or machine
compacting method.
e) Cure the slanting surface by placing jute bags which will hold the waste for some time.
Water curing should be done at least five times a day and should be continued for10-
14 days depending upon span.
Method:
a) For the production of precast reinforced cement concrete joists, refer to the section on
precast reinforced cement concrete planks and joists.
b) Joists are placed b/n walls or beams and steel ties are to be provided to arrest lateral
movements of the joists.
c) A sliding type of mould is placed b/n two joists.
d) Arch with wire cut bricks in 1:6 cement mortar is constructed immediate de-molding
of the newly constructed arch is done by sliding the mould to the position where the
next arch is to be constructed.
The term ‘cost’ means the amount of expenses [actual or notional] incurred on or attributable
to specified thing or activity. As per Institute of cost and work accounts (ICWA) India, Cost is
‘measurement in monetary terms of the amount of resources used for the purpose of production
of goods or rendering services.
Material:
To produce or manufacture material is required. For example to manufacture shirts cloth is
required and to produce flour wheat is required. All material which becomes an integral part of
finished product and which can be conveniently assigned to specific physical unit is termed as
“Direct Material”. It is also described as raw material. The substance from which the product
is made is known as material. It may be in a raw or manufactured state. Material is classified
into two categories:
1. Direct Material
2. Indirect Material
Direct material
Direct Material is that material which can be easily identified and related with specific product,
job, and process. Timber is a raw material for making furniture, cloth for making garments,
sugarcane for making sugar, and Gold/ silver for making jewellery, etc are some examples of
direct material.
Indirect material
Indirect Material is that material which cannot be easily and conveniently identified and related
with a particular product, job, process, and activity. Consumable stores, oil and waste, printing
and stationery etc, are some examples of indirect material. Indirect materials are used in the
factory, the office, or the selling and distribution department.
Labour
Labour is the main factor of production. For conversion of raw material into finished goods,
human resource is needed, and such human resource is termed as labour. Labour cost is the
main element of cost in a product or service. Labour can be classified into two categories:
1. Direct Labour, and
2. Indirect labour
Direct labour
Labour which takes active and direct part in the production of a commodity. Direct labour is
that labour which can be easily identified and related with specific product, job, process, and
activity. Direct labour cost is easily traceable to specific products. Direct labour costs are
specially and conveniently traceable to specific products. Direct labour varies directly with the
volume of output. Cost of wages paid to carpenter for making furniture, cost of a tailor in
producing readymade garments, cost of washer in dry cleaning unit are some examples of direct
labour.
Indirect labour
Indirect labour is that labour which can not be easily identified and related with specific
product, job, process, and activity. It includes all labour not directly engaged in converting raw
material into finished product. It may or may not vary directly with the volume of output.
Labour \ employed for the purpose of carrying out tasks incidental to goods or services
provided is indirect labour. Indirect labour is used in the factory, the office, or the selling and
Expenses
All cost incurred in the production of finished goods other than material cost and labour cost
are termed as expenses. Expenses are classified into two categories:
1. Direct expenses, and
2. Indirect
Direct expenses
These are expenses which are directly, easily, and wholly allocated to specific cost center or
cost units. All direct cost other than direct material and direct labour are termed as direct
expenses.
Direct expenses are also termed as chargeable expenses. Some examples of the direct expenses
are hire of special machinery, cost of special designs, moulds or patterns, feed paid to
architects, surveyors and other consultants, inward carriage and freight charges on special
material, Cost of patents and royalties.
.
Indirect expenses
These expenses cannot be directly, easily, and wholly allocated to specific cost center or cost
units. All indirect costs other than indirect material and indirect labour are termed as indirect
expenses. Thus, Indirect Expenses = Indirect cost – Indirect material – Indirect labour.
Indirect expenses are treated as part of overheads. Rent, rates and taxes of building, repair,
insurance and depreciation on fixed assets, etc, are some examples of indirect expenses.
OVERHEADS: MEANING
The term overhead has a wider meaning than the term indirect expenses. Overheads include
the cost of indirect material, indirect labour and indirect expenses. This is the aggregate sum
of indirect material, indirect labour and indirect expenses.
Overhead = Indirect material + Indirect labour + Indirect expenses
Overheads are classified into following three categories:
1. Factory/works/ production overheads
2. Office and administrative overheads
3. Selling and distribution overheads
Factory/works overheads
All indirect costs incurred in the factory for production of goods is termed as factory/works
overheads. Such costs are concerned with the running of the factory or plant. These include
indirect material, indirect labour and indirect expenses incurred in the factory. Some examples
are as follows:
Indirect materials:
(i) Grease, oil, lubricants, cotton waste etc.
(ii) Small tools, brushes for sweeping, sundry supplies etc.
(iii) Cost of threads, gum, nails, etc.
(iv) Consumable stores
(v) Factory printing and stationery
Indirect wages
(i) Salary of factory manager, foremen, supervisors, clerks etc.
(ii) Salary of storekeeper
(iii) Salary and fee of factory directors and technical directors
(iv) Contribution to ESI, PF., Leave pay etc. of factory employee.
Indirect expenses
(i) Rent of factory buildings and land
(ii) Insurance of factory building, plant, and machinery
(iii) Municipal taxes of factory building
(iv) Depreciation of factory building, plant and machinery, and their repairs and maintenance
charges
(v) Power and fuel used in factory
(vi) Factory telephone expenses.
administrative directors, Salaries of legal adviser, Salaries of cost accountants and financial
accountants, Salary of computer operator. Rent, insurance, rates and taxes of office building,
Office lighting, heating and cleaning, Depreciation and repair of office building, furniture, and
Equipment etc., Legal charges, Bank charges, Trade subscriptions, Telephone charges, Audit
fee etc.
I. Selling overheads
Indirect costs incurred in relation to the procurement of sale orders are termed as selling
overheads. Some of the examples of selling overheads are as follows
Indirect material
(i) Catalogues, price list (ii) Printing and stationery
(iii) Postage and stamps (iv) cost of sample
Indirect wages
(i) Salaries of sales managers, clerks and other employees
(ii) Salaries and commission of salesmen and technical representatives
(iii) Fees of sales directors
Indirect expenses
(i) Advertising
(ii) Bad debts
(iii) Rent and insurance of showroom
(iv) Legal charges incurred for recovery of debts
(v) Travelling and entertainment expenses
(vi) Expenses of sending samples
(vii) Market research expenses.
Indirect costs incurred in relation to the execution of the sales order is termed as distribution
overheads. Some of the examples of distribution overheads are as follows:
Indirect material
(i) Cost of packing material
(ii) oil, grease, spare parts etc. for maintaining delivery vans
Indirect wages
(i) Salaries of godown employees
(ii) Wages of drivers of delivery vans
(iii) Wages of packers and dispatch staff.
Indirect expenses
(1) Packing expenses
(ii) Godown rent, insurance, depreciation, and repair etc.
(iii) Freight carriage outwards and other transport charges.
(iv) Running expenses of delivery vans, repair, and depreciation.
(v) Insurance in transit etc
Labour
Labour is the main factor of production. For conversion of raw material into finished goods,
human resource is needed, and such human resource is termed as labour. Labour cost is the
main element of cost in a product or service. Labour can be classified into two categories:
1. Direct Labour, and
2. Indirect labour
Direct labour
Labour which takes active and direct part in the production of a commodity. Direct labour is
that labour which can be easily identified and related with specific product, job, process, and
activity. Direct labour cost is easily traceable to specific products. Direct labour costs are
specially and conveniently traceable to specific products. Direct labour varies directly with the
volume of output. Direct labour is also known as process labour, productive labour, operating
labour, direct wages, manufacturing wages, etc. Cost of wages paid to carpenter for making
furniture, cost of a tailor in producing readymade garments, cost of washer in dry cleaning unit
are some examples of direct labour.
Indirect labour
Indirect labour is that labour which can not be easily identified and related with specific
product, job, process, and activity. It includes all labour not directly engaged in converting raw
material into finished product. It may or may not vary directly with the volume of output.
Labour employed for the purpose of carrying out tasks incidental to goods or services provided
is indirect labour. Indirect labour is used in the factory, the office, or the selling and distribution
department. Wages of store-keepers, time-keepers, salary of works manager, salary of
salesmen, etc, are all examples of indirect labour cost.
The cost-saving construction methods presented in this model are technically oriented, and
focus on the design and construction of particular features in and around the home. They can
be generally classified into basic suggestions that:
Substitute materials that are less expensive to purchase and/or install than more
common alternatives. Examples include use of less expensive sheathing products,
plastic plumbing products instead of copper, and corrugated stainless steel gas pipe
instead of black iron pipe;
Involve more innovative alternative products that simplify overall construction, such as
mechanical plumbing vents in lieu of through foundation systems instead of deep
footings in cold climates;
Save money by eliminating overdesigned or unnecessary features, including 24-inch
stud spacing rather than 16-inch, 2 x 3 studs instead of 2 x 4s in nonbearing walls, and
reduced plumbing vent pipe sizes; and
Focus on residential land planning and land development, such as increased density,
clustered development reduced street widths, and elimination or simplification of
technically questionable development requirements.
FOUNDATIONS
Foundations typically consist of a concrete block or poured concrete wall placed on top of a
concrete spread footing that rests on the soil. They are designed to support all building loads
safely, and are located at a depth that is sufficient to prevent frost heave. New methods and
materials that achieve these design objectives have been gaining popularity as cost-saving
alternatives to the more traditional approaches. Methods and materials that offer potential
savings are discussed below.
1. Arch foundation: Already explained
2. Monolithic Slab-on-Grade Foundation
The number of steps involved in foundation construction can be reduced by using a monolithic
slab-on-grade foundation design. A monolithic slab-on-grade installation consolidates the
operation of casting a separate footing and pouring a floor slab. These both reduce labor, and
also cuts the time required to build a typical slab on – grade foundations by 1 or 2 days.
WALLS:
1. Rat trap bonded brick masonry
2. Cement stabilized mud block masonry
3. Interlocking cement stabilized mud block masonry
4. Stone concrete block
5. Combined wire cut and country brick masonry
OPENIGNS:
1. Precast reinforced cement concrete lintel
2. Brick and reinforced cement concrete lintel
3. Brick arch
ROOFS:
1. Precast reinforced cement concrete channels
2. Precast reinforced cement concrete planks & joists
3. Precast Ferro-cement channels
4. Folded filler slab with Mangalore tiles
5. Jack arch with bricks and precast reinforced cement concrete joist
6. Stone roofing on precast reinforced cement concrete joist
7. Micro concrete tiles on steel under structure.
8. Reinforced cement concrete ribbed brick slab
9. Corbelled brick pyramid.
10. Corbelled brick arch roof.
FRAMING
Framing offers some of the best opportunities to reduce costs during rehabilitation and new
construction. Considerable effort has been directed at value-engineering residential framing.
Examples of some of the most widely used cost-saving methods are discussed below.
Electrical
Electrical installation is typically governed by provisions of the national electrical codes or
similar codes. Even within these stringent codes, however, there are ways to reduce costs using
low-cost products that are meet the intent of the codes.
Surface mount electrical conduit and behind –baseboard installation:
Traditional methods for installing electrical wiring inside walls work well with new
construction, but this approach is much more difficult and costly in rehabilitation work. Surface
–mount electrical conduit and behind installations are two alternative approaches. surface
mount conduit is fairly well known, but behind –baseboard raceways systems, are likely to be
more acceptable to occupants. An example of this type of system is plastic base board that has
a hallow space to fish electric wiring through. Sometimes have multiple raceways built into the
baseboard so that a number of cables can be routed through the system.
Savings from Surface-Mount Conduits and Baseboard Raceways
Installing surface-mount electrical conduits or baseboard raceways can save from 25 to 40
percent on electrical costs when compared with traditional methods of running electric wire.
Surface mounting leaves sound walls undisturbed and avoids problems with concrete floors.
Plastic electric boxes:
In many areas, metal electric boxes are the norm for light switches, wall outlets, and other
applications. The plastic electric box, however, is a low cost alternative that is widely available
and relatively simple to install. Plastic electric boxes are generally accepted under national
electric codes.
Plumbing:
For years, plumbers have followed numerous rules of thumb which, although based on years
of practical experience, do not apply to many of today’s plumbing materials. Research that
supports the newer cost effective approaches has begun to find its way into the codes.
Mechanical plumbing:
Traditionally, plumbing vents are installed for each fixture and extend up through the roof. The
introduction of mechanical vents has eliminated this need, instead allowing the vent to
terminate just above the fixture. These devices are useful in situations where it is difficult to
install vents for fixtures-they can eliminate the need to open additional walls and floors in a
rehabilitation project. Mechanical vents are accepted in most major plumbing codes and are
available through plumbing supply and building supply store.
Direct venting of drain waste-vent pipes:
Like mechanical plumbing vents, dirct venting is useful when it is difficult or costly to install
a traditional “through-the- roof” plumbing vent. Direct vents are plumbing vents that terminate
through a wall directly to the exterior.
Stack or wet venting of drain-waste vent pipe:
Stack and wet venting of DWV pipe amount of total pipe in the plumbing system by reducing
the requirement for a separate vent for each fixture. For example, where plumbing fixtures on
one floor are located above or below fixtures on another floor, both may be vented through the
same pipe
Pipe materials:
In most major model codes, acceptable water service pipes materials include polyvinyl chloride
and other plastics that are often less costly than copper pipe. For example, polybutylene plastic
pipe, a flexible pipe that requires fewer fittings than rigid pipes easier to install and thus less
costly than rigid pipes.PVC and polyethylene water service pipes should only be used for cold
water distribution.
Savings from Use of Alternate Pipe Materials
Polybutylene supply pipe was used instead of copper. As a result, plumbing costs were reduced
by Rs 65 per unit. Field studies have shown 30 to 50 percent savings when flexible
polybutylene supply piping is substituted for rigid pipe materials.
Water services:
Insulating utilities, both main lines and service laterals, offers significant opportunities to
reduce new construction costs.
Common lateral water pipes
Many communications require that each property have its own water services, but a common
or shared water service pipes, sized to handle the required water flow, can serve several homes,
saving labor and material cost.
SEWAGE DISPOSAL
Cost-saving technologies can be used for both publicly sewered property and for homes served
by individual on-site waste treatment and disposal systems. Although the latest sewage disposal
technologies are mainly intended for new construction, several also have rehabilitation
potential, particularly on-site disposal methods. New sewage technologies can often be applied
to older buildings that have failing septic systems. In fact, these methods may be the only
economically sound way to rehabilitate the property.
Common Lateral Sewer Pipes
Many communities require that every home have a separate lateral sewer pipe that connects to
the main sewer pipe. A common or shared lateral sewer pipe , sized to handle required flow,
can be used to serve several homes.
Common Trench for Water and Sewer Pipes Sand Mound Septic System
In areas where the groundwater table is elevated, where there is a shallow barrier below the
soil, or where soils are slowly permeable, a conventional septic system is not suitable for
wastewater disposal. Many jurisdictions do not permit new systems in these sites, which
effectively reduces the land available for housing. When older, existing systems in areas with
poor soil conditions fail they must be replaced with properly operating systems.
One solution in these areas is to install a sand mound or mound system. A mound system is a
drainfield that is installed in a mound above the natural lot elevation on a suitable fill, usually
a medium textured sand. Sand mound system design criteria are available from a variety of
sources, including the U.S. Environmental Protection
Sand Mound Septic System
In areas where the groundwater table is elevated, where there is a shallow barrier below the
soil, or where soils are slowly permeable, a conventional septic system is not suitable for
wastewater disposal. Many jurisdictions do not permit new systems in these sites, which
effectively reduces the land available for housing. When older, existing systems in areas with
poor soil conditions fail they must be replaced with properly operating systems.
One solution in these areas is to install a sand mound or mound system. A mound system is a
drainfield that is installed in a mound above the natural lot elevation on a suitable fill, usually
a medium textured sand. Sand mound system design criteria are available from a variety of
sources, including the U.S. Environmental Protection
Recirculating Sand Filter Septic Systems
In many unsewered areas, conventional septic systems are unacceptable because of slowly
permeable soils. Land on these soils is, therefore, deemed” nonbuildable.” Furthermore, many
rehabilitation projects are severely limited in tions on the amount of living space; i.e., system
expansion is not permitted because the sewerage from a larger home might exceed the capacity
of a system that is already failing. Recirculating sandfilter systems can be used in areas with
slowly permeable soil, and also provide higher quality effluent. Although a recirculating sand
filter contains many of the features of a conventional septic system, it also has a sand filter
installed between the septic tank and the drainfield. Wastewater is sprayapplied to the filter and
then recirculated several times back to the septic tank, or to a separate Wastewater effluent
from a sand filter system is of higher quality than septic tank effluent. The higher quality
increases the ”acceptance rate” of the soil by a factor as high as 7 to 8. This translates into a
smaller drainfield, and means that smaller lots can be served by a sand filter system than by a
conventional septic system. Although they have been shown to work effectively, circulating
sand filters are not yet widely recognized. Thus, local health officials should be Wastewater
effluent from a sand filter system is of higher quality than septic tank effluent. The higher
quality increases the ”acceptance rate” of the soil by a factor as high as 7 to 8. This translates
into a smaller drainfield, and means that smaller lots can be served by a sand filter system than
by a conventional septic system. Although they have been shown to work effectively,
circulating sand filters are not yet widely
recognized. Thus, local health officials should be consulted before using this type of system.
Design guidelines for sand filter systems have been produced by the U.S. Environmental
Protection
Setback Requirements
Reduction of the generally arbitrarily determined minimum front yard, side yard, and rear yard
setbacks as well as space between units, can save land costs as well as utility and infrastructure
costs. Large setbacks from all boundaries place the house near the center of the lot and reduce
its usability. Using the "zero-lot-line" technique, homes can be located on one or more lot-
lines, creating a single, usable yard area rather than two narrow unusable sideyards. To ease
privacy concerns, walls that are located on the lot lines may be required to be windowless, with
a small easement granted for maintenance. (Figure 17) 20-Cost-Saving Construction
Opportunities and the HOME Program the greater the number of homes to share land ment
costs per home are less for 100 homes built on a 10-acre tract than for 40 homes on the same
tract. Smaller lots also reduce the linear footage of curbs, gutters, and utilities required for each
house.
Site development:
Two costs are associated with developing a site for housing- the cost of purchasing raw or
under developed land and cost of improving or developing that land. Not only have the cost of
raw lots increased, but so also have land development costs, largly as a result of excessive local
requirements , i.e, wide streets and rights –of- way, and overdesigned water and utility supply
system.
Housing density also effects land development costs-the higher the number of homes per acre,
the greater the number of homes to share land development costs. For example, land
development costs per homeare less for 100 homes built on a 10-acre tract than 40 home on
the same tract. Smaller lots also reduce the linear footage of curbs, gutters, and utilities required
for each house.
A development budget study is undertaken to determine the total costs and returns expected
from the project. A cost plan is prepared to include all construction costs, all other items of
project cost including professional fees and contingency. All costs included in the cost plan
will also be included in the development budget in addition to the developer’s returns and other
extraneous items such as project insurance, surveys and agent’s or other specialist advisers’
fees.
The purpose of the cost plan is to allocate the budget to the main elements of the project to
provide a basis for cost control. The terms budget and cost plan are often regarded as
synonymous. However, the difference is that the budget is the limit of expenditure defined for
the project, whereas the cost plan is the definition of what the money will be spent on and
when. The cost plan should, therefore, include the best possible estimate of the cash flow for
the project and should also set targets for future running costs. The cost plan should cover all
stages of the project and will be the essential reference against which the project costs are
managed.
The method used to determine the budget will vary at different stages of the project, although
the degree of certainty should increase as project elements become better defined. The budget
should be based on the client’s business case and should change only if the business case
changes. The aim of cost control is to produce the best possible building within the budget
The cost plan provides the basis for a cash flow plan, allocating expenditure and income to
each period of the client’s financial year. The expenditures should be given at a stated base-
date level and at out-turn levels based upon a stated forecast of inflation.
The objective of cost control is to manage the delivery of the project within the approved
budget. Regular cost reporting will facilitate, at all times, the best possible estimate of:
Monitoring expenditure to any particular date does not exert any control over future
expenditure and, therefore, the final cost of the project. Effective cost control is achieved when
the whole of the project team adopts the correct attitude to cost.
Establishing that all decisions taken during design and construction are based on a
forecast of the cost implications of the alternatives being considered, and that no
decisions are taken whose cost implications would cause the total budget to be
exceeded.
Encouraging the project team to design within the cost plan at all stages and follow the
variation/change and design development control procedures for the project. It is
generally acknowledged that 80% of cost is determined by design and 20% by
construction. It is important that the project team is aware that no member of the team
has the authority to increase costs on its section or element of the work. Increased costs
on one item must always be balanced by savings on another.
Regularly updating and reissuing the cost plan and variation orders causing any
alterations to the brief.
Adjusting the cash flow plan to reflect alterations in the target cost, the master schedule
or the forecast of inflation.
Developing the cost plan in liaison with the project team as design and construction
progress. At all times it should comprise the best possible estimate of the final cost of
the project and of the future cash flow. Adherence to design freezes will aid cost control.
Developing the cost pan also involves adding detail as more information about the work
is assembled, replacing cost forecasts with more accurate forecasts or actual costs
whenever better information can be obtained.
Reviewing contingency and risk allowances at intervals and reporting the assessments
is an essential part of risk management procedures. Developing the cost plan should not
involve increasing the total cost.
Checking that the agreed change management process is strictly followed at all stages
of the project. The procedure should only be carried out retrospectively, and then only
during the construction phase of the project, when it can be demonstrated that otherwise
significant delay, cost or danger would have been incurred by awaiting responses.
Arranging for the contractor to be given the correct information at the correct time in
order to minimise claims. Any anticipated or expected claims should be reported to the
client and included in the regular cost reports.
Contingency provisions are based on a thorough evaluation of the risks and are
available to pay for events which are unforeseen and unforeseeable. It should not be
used to cover; changes in the specification, changes in the client’s requirements or
variations resulting from errors or omissions. Should the consultants consider that there
is no alternative but to exceed the budget, a written request must be submitted to the
client and the correct authorisation received. This must include the following:
Submitting regular, up-to-date and accurate cost reports to keep the client well informed
of the current budgetary and cost situation.
Ensuring that all parties are clear about the meaning of each entry in the cost report. No
data should be incorrectly entered into the budget report or any incorrect deductions
made from it.
Ensuring that the project costs are always reported back against the original approved
budget. Any subsequent variations to the budget must be clearly indicated in the cost
reports.
Effective cost management requires preconstruction planning that clearly communicates and
analyzes the costs of individual project components and systems. The cost-management
process uses estimating, benchmarking and value engineering not as discrete tools, but as
preconstruction planning services.
Benchmarking is used both for developing estimates and for verifying that the costs of each
component and system fall within the proper range for projects of that type. Value engineering
looks at a project’s performance goals and analyzes the most cost-effective ways to meet them.
The experienced construction manager maintains a database for projects of similar scope and
building type from which to draw, analyze and compare costs.
Communications Tool
Clearly, the key to effective cost management is information — estimating, benchmarking and
value engineering analyses that are carefully compiled and presented. In the right hands, such
data can go a long way toward ensuring a project that is designed within budget objectives,
meets agreed-to performance and quality goals and provides information that shortens the
project schedule.
To ease decision making, project budgets should be configured so that each component and
building or process system is isolated and presented. This allows system component costs to
be compared to those of similar projects for the development of a benchmark analysis. This
approach varies from the structure generally used, in which cost information is presented for
the entire project according to a Construction Specifications Institute format. That format
identifies the total cost of concrete, masonry, carpentry, plumbing, electrical and other
specification categories.
The standard estimating technique often does not take into account the kinds of information
needed to make cost-effective decisions. Consider a planned corporate headquarters
comprising a dining facility, conference center, fitness center and office buildings. The typical
approach would be to estimate the total cost of each CSI specification category.
A more effective means of communicating costs is first to dissect the components. Analyze the
costs of the dining facility, conference center, fitness center and office buildings individually
and compare them with those of similar corporate projects. Doing so would allow the facility
executive to identify whether certain elements of the project, such as the fitness center, need to
be scaled down or eliminated based on their cost relative to the whole project. Alternatively, it
might allow the facility executive to be convinced that some elements represent a cost-effective
investment.
Explanatory Tools
Next, the estimating and benchmarking process should examine not the total cost of concrete,
for example, but rather the individual costs of the foundation system versus the structural
system. By separating these, it is possible to attribute the cost of the foundation when
benchmarked against those of similar projects. Hypothetically, a higher cost might be caused
by the configuration of the site. If the project is being built into a hill, for example, foundations
will cost more than those of similar projects.
As the project design progresses, benchmarked estimates provide increasing levels of detail.
At every step, the process develops details needed to understand whether each component’s
estimated cost fits within a benchmarked range and if not, why not. The process also enables
the project team to examine whether there are more cost-effective ways to meet performance
goals.
Isolating and benchmarking costs identifies areas where the greatest cost savings exist without
sacrificing scope, quality or architectural appeal.
An effective approach to value engineering asks how buildings can be designed to cost-
effectively meet design and functional goals. To take this approach, look first at how individual
components and systems meet the building’s performance goals, then at the design standards
and sizes of systems and components, and finally at the details and materials.
1. Define the scope, the level of quality desired, and the budget
2. Ensure that the scope, quality, and budget are aligned
3. Monitor and manage the balance of these three components throughout the life of the
project
Milestone cost estimates at various stages of the process are critical components of the cost
management activity. Cost Management encompasses more than cost estimates however—it
also includes Risk Management and in the federal arena, can include Earned Value Analysis.
Risk Assessment and Management are important as identified risks on construction projects
are typically financial in nature. Therefore early in the project an assessment of risk is crucial
to establish the budget parameters within which the project must be completed. The calculation
of project contingencies should be based on an assessment of the risk surrounding the project
(site issues, availability of bidders, method of procurement, and critically the market conditions
in the location of the project. As risks are mitigated (site investigation is done, market survey
completed, program finalized, design started, and so forth) then contingencies can be reduced
and the range of estimated final cost narrowed.
The firm charged with managing the costs of the project should ideally be hired directly by the
owner, early in the process, and should be independent of both the architect/engineer and the
construction contractor.
Planning Phase
Cost Management differs from Building Economics in that it is typically concerned with the
initial costs—or first costs—of accomplishing new construction or renovation projects. A
project must start right in order for it to finish right, so the establishment of an appropriate
budget is critical. Early in the planning stages, both building owners and designers must agree
on an anticipated cost of the project at bid award. This is a critical stage in the cost management
process—an inaccurate budget can doom a project to continual stress and compromise, with
neither the owner, end-user, nor design team being completely satisfied at the end. A common
mistake at this stage is to take a program of areas and apply those to historical costs without
making adjustments for the myriad factors which affect construction costs—size of the project,
renovation versus new, location (has a market survey been done?), price increases since the
date of the data used, method of procurement, overall quality of the space envisioned, LEED
rating desired if any, access and locational factors such as dense urban, traffic and sidewalk
protection, water location, bid competitiveness in the local market, etc.
Preliminary Estimates are employed in the early planning phases of a proposed project to match
an owner's needs, expressed as written programmatic requirements, with budget constraints in
order to establish its overall scope (size) and quality expectations.
The proposed method of procurement, or delivery approach in the above graphic, should be
identified at this stage. The options available today are more numerous than in the past—
traditional Lump Sum, Construction Manager as Constructor (CMC) (also known as CM at
Risk), Design/Build, Integrated Project Delivery (IPD) and so forth. Each method has pros and
cons relative to cost and risk, so the method selected should also be factored in to the project
budget. These can generally be summarized as follows:
Traditional Design-Bid-Build
Issues Advantages Disadvantages
Cost and Budget "Best price" potential Cost not finalized until bids
Management Perception of "best price" Cost overruns after bid require
expensive redesign
Bidders may seek to "get low" by
omitting owrk not clearly shown
Design-Build
Issues Advantages Disadvantages
Cost and Budget Early cost guarantee Fair price competition difficult to
Management Price tends to match quality verify
Can obtain best price for Cost impact of risk issues may
performance not be evident in initial pricing
Owner over-emphasis on price as
a selection criteria may force the
design-builder to compromise
quality to reduce price
Schedule Construction can start after very Schedule changes at any point
Impact and preliminary design after pricing difficult to
Management Generally considered as most implement
beneficial schedule approach Use of "bridging" type approach
may expand schedule
Integrated Project Delivery as a procurement method is gaining some traction in the industry,
although it still only is used on 1–2% of projects and legal difficulties around liability remain
a hurdle for broader acceptance. From a cost management perspective the benefits remain
elusive as the various parties on the team generally have differing objectives, although
doubtless the coordination of the trades and cohesiveness of the design may impart some time
savings and reduced change orders during construction. The use of Building Information
Modeling (BIM) is likewise a growing trend and from an owner's perspective a very useful
tool, with similar benefits to IPD but few documented advantages related to cost management.
While the technology is improving, the quality of estimates produced from BIM models is still
fairly uneven. Quantity take-offs are becoming more accurate (although still highly dependent
on the accuracy of the data entered into the model) but the pricing aspects and the capture of
components not yet in the model still require considerable scrutiny by the cost estimator.
Value Engineering should also be considered at this stage. Any changes to the program at this
early phase have very little, if any, impact on schedule and A/E time and redesign costs, but
the benefits in terms of solidifying the program and establishing project goals can be huge.
Design Phase
Once an initial budget has been established, the scope set and the quality expectations
documented, it is important to monitor the estimated cost of the project by employing a series
of increasingly precise cost estimating techniques that coincide with further development of
design and construction details.
Intermediate estimates are employed at various stages of project design development as part of
ongoing cost management, and as a means of evaluating competing alternative construction
assemblies, systems, and materials. On large projects it is common practice for an owner to
employ a construction manager or professional estimator to continually update project
estimates and provide feedback on budget impacts of decisions on major design elements. The
drawings and specifications should also go through a constructability review, wherein an
independent review team analyzes the construction documents for completeness, coordination
between disciplines, cost-effective design solutions, and general code compliance (as
mentioned earlier this is where BIM and IPD bring significant benefits). The specifications
should also be reviewed to ensure that the General Requirements included in division 1 are not
overly restrictive (e.g. working hours, noise restrictions and so forth) and that throughout the
specifications the use of proprietary materials is minimized. A market survey should have been
carried out on sizable projects to determine where the bidders will come from—is the local
market sufficiently large to accommodate the project, or will the major subcontractors be at
capacity and therefore likely to bid high, if at all? It's often worth re-verifying the market survey
if one was done much earlier in the process.
The estimates become much more refined in parallel with the refinement of the design,
ultimately resulting in a pre-bid estimate that captures the entirety of the project.
Earned Value Analysis is a useful tool in cost management, in that costs for each component
of the project (in a Work Breakdown Structure, or WBS) can be tracked against the initial
budget, and adjustments made to ensure the overall budget is on track. Movements between
components are common; however, without tracking where costs are changing, the budget is
in danger of being exceeded leading to re-design or extensive value engineering. Similarly
future cost planning can be improved by the use of Earned Value Analysis, by tracking where
the money really goes in a project.
Procurement Phase
At the bid stage, the drawings should be 100% complete; however, in many instances this does
not happen, leading to addenda being issued to clarify details, resolve conflicts or to complete
the design. Often the estimate is not adjusted to account for these design changes, leading to a
so-called final estimate that really does not represent the scope of work being bid. The estimate
should therefore be adjusted during bidding to reflect the same information the bidders receive.
Also a read of the market at bid stage is still useful, and can be included in a risk assessment to
determine a range of bids expected. In a particularly volatile market, the use of bid options may
allow the owner some flexibility in achieving the budget on bid day.
The preparation of the bidding documents is also crucial in an overall cost management
strategy. Consideration should be given to contract clauses that govern changes in the work
and how they will be valued (e.g. by reference to a published price book or trade manual);
allowable mark-ups on changes by the various levels of contractors and sub-contractors; notice
requirements for delays; the use of unit prices for changes and any other clauses that may affect
the final cost of the project.
Construction Phase
During construction the focus shifts from predictive cost estimating to reactive cost
management of any changes in the work. Changes arise from a number of different sources—
unforeseen conditions, owner-generated changes, drawing errors and omissions, code issues or
contractual claims. Also changes can arise from on-going proactive cost management, either
generated by the design team or the general contractor, where one of the parties proposes a
better-value substitution (sometimes known as Value Engineering Change Proposals or
VECPs). For all reviews of changes the owner should first establish the ground rules as
delineated in the contract documents, agree a format with the general contractor, and require
the general contractor to first review change proposal from subcontractors before compiling
and forwarding to the owner. Changes should also be reviewed by the design team for
entitlement—is it really a change to the scope and are there any credits due? Then the agency
Construction Manager or independent cost consultant should review the pricing against the
contract and industry norms, leading to an independent government estimate for presentation
to the general contractor. Wherever possible the value of the change should be agreed before
the work is installed, otherwise the owner's leverage to agree a fair and reasonable price is
greatly diminished.
To provide data for future cost management, an evaluation is often carried out to prepare a
detailed cost analysis of the completed project and to develop lessons learned to inform future
design decisions. The cost data captured should also be fed back in to the owner's database to
better inform future estimates and budgets. Other areas to consider here include a review of
energy performance of the building during occupancy, to ascertain if the data used as the basis
for selection of the mechanical and electrical systems and components was accurate vis-a-vis
the actual performance.
A cost analysis (also called cost-benefit analysis, or CBA) is a detailed outline of the potential
risks and gains of a projected venture. Many factors are involved, including some abstract
considerations, making the creation of a CBA more of an art than a science, though a
quantitative mindset is still a must-have. A CBA is useful for making many types of business
and personal decisions, especially ones with a potential for profit (though this need not be the
case). Although conducting a CBA can be a complex task, you do not need to be a business
major to learn how to do so. Anyone who's willing to brainstorm, research, and analyze data
can make a top-quality CBA.
Cost-benefit analysis (CBA) is a tool used to determine the worth of a project, programme or
policy. It is used to assist in making judgments and appraising available options. CBA
principles and practice are well established – as evidenced by the vast amounts of literature
available from academics, CBA practitioners, and government agencies (both domestically and
abroad). CBA is a quantitative analytical tool to aid decision-makers in the effi cient allocation
of resources. It identifi es and attempts to quantify the costs and benefi ts of a programme or
activity and converts available data into manageable information. The strength of the method
is that it provides a framework for analysing data in a logical and consistent way. CBA helps
managers answer questions such as:
1. Does the proposal provide a net benefi t to the community as a whole
2. Should the proposed project, programme or policy be undertaken?
3. Should the project or programme be continued?
Types of evaluations
There are many ways to evaluate programmes and activities. However, there are three methods
that have frequent relevance to Australian Government agencies. These methods are:
• CBA;
• fi nancial evaluation; and
• cost-effectiveness analysis.
Financial and cost-effectiveness analyses are alternative methods to CBA but share some
common characteristics. These alternative methods are summarised below. Section C of this
Introduction to CBA provides a more extensive discussion.
Cost-Benefit Analysis
CBA is a methodology for assessing the net benefits accruing to society as a whole as a result
of a project, programme or policy. Most often a CBA is conducted from the point of view of
the
local country or possibly the international community as well. It can, in principle, be conducted
from the perspective of a state, a region, or even a local community, but such a restricted
approach is less common. The appropriate time period over which a CBA should be conducted
is generally the projected life of the project or programme.
The CBA method considers the fl ow of real resource costs and benefi ts, and excludes, for
example, taxes and subsidies, which are regarded as transfer payments from one part of
the economy to another. CBA attempts to measure the value of all costs and benefi ts that
are expected to result from the activity. It includes estimating costs and benefi ts which are
‘unpriced’ and not the subject of normal market transactions but which nevertheless entail
the use of real resources.
Financial Evaluation
A fi nancial evaluation (or ‘investment evaluation’) is generally conducted from the perspective
of an individual fi rm or agency rather than from the vantage point of the community as a
whole. It is essentially concerned with assessing the impact of a programme or project on
the organisation’s own fi nancial performance. A fi nancial evaluation can be used to answer
the question of whether a proposal offers an acceptable return from an organisation’s
perspective. Financial evaluations can be used for other reasons – such as determining the
lowest cost procurement method – but the Introduction to CBA is primarily focussed on
evaluating programmes and projects.
In a fi nancial evaluation, only cash fl ows in and out of the organisation are considered; cash
fl ows involving other parties are excluded, as are ‘unpriced’ costs and benefi ts. Unlike CBA,
the relevant money values include the effects of taxes and subsidies on the relevant agency.
Cost-Effectiveness Analysis
Cost-effectiveness analysis (CEA) is aimed at determining the cost of achieving a specifi c
physical target. Such studies may be undertaken from a national or local perspective. They
differ from CBA in that benefi ts are expressed in physical units rather than in money units.
Costs, as in CBA, are expressed in money terms. In relaxing the approach towards benefi ts
measurement, CEA is useful in areas such as health, accident safety and education where it is
often easier to quantify benefi ts in physical terms than to value them in dollars.
CBA is generally the preferred method when markets or prices do not adequately refl ect
all the costs and benefi ts of a proposal. When markets are competitive and most costs and
benefi ts are refl ected in market prices, fi nancial evaluation can provide an adequate guide
to the social viability of a proposal. Financial evaluation is also important when government
as a whole or an agency of government has fi nancial objectives or responsibilities to
fulfi l or when it is involved in a purely fi nancial decision such as a comparison of different
procurement methods (e.g. traditional government ownership vs. outsourcing). CEA is useful
most often when the benefi ts of a proposal are diffi cult to quantify in monetary terms but
the government wishes to know which option will achieve social benefi ts or government
objectives most cost effectively.
If outcomes cannot be quantified in money terms, it is not possible to undertake a formal CBA.
However, there is an increasing volume of economic literature directed towards finding ways
to attach dollar values to benefits so they can be measured on the same basis as costs, thus
allowing comparisons to be made between alternative uses of public funds. For example,
additional future earnings of trainees compared with what they would have gained otherwise
may provide an indication of the benefit of a training programme. When valuing the cost of
aircraft noise, the difference between house prices under aircraft flight paths and those not
under them may provide a reasonable guide. However, while useful, the estimation of dollar
values in such circumstances often involves a significant degree of judgment and imprecision.
Another alternative is to quantify benefits as much as possible and determine ratios of the
quantity of benefits per dollar spent, i.e. undertake a cost-effectiveness analysis. This approach
may be useful when specific physical outcomes are compared but provides little policy
guidance when comparing different outcomes, such as lives saved and children educated.
CBA in practice
In practice, CBA studies are diverse in terms of size, sector, approach and impact. Typical
examples undertaken by Australian Government agencies include CBAs of infrastructure
proposals (e.g. roads, dams, rail), agricultural, environmental, and scientific research,
information technology and property sales/acquisitions. The assessment of costs and benefits
is also undertaken in determining the impact of proposed regulation. The Office of Regulation