HCIA-R&S Dumps v2.2 PDF

H12-211.prepaway.premium.exam.
279q
Number: H12-211
Passing Score: 800
Time Limit: 120 min
File Version: 9.0
H12-211
Huawei Certified Network Associate- Huawei Networking Technology and Device
Version 9.0
Jul 24, 2019

Exam A
QUESTION 1
An administrator currently manages AR2200 devices in the network through a single password, however the
company wishes to introduce another two administrators and provide unique user credentials and privilege
levels for telnet access to the network devices.
What action can be taken? (Choose three)
A. Configure three users under the AAA-view, and assign each a different password.
B. The authentication mode must be changed to AAA.
C. Each administrator must be assigned a privilege level.
D. A public IP address must be assigned to each user for telnet access
Correct Answer: ABC

Section: (none)
Explanation
Explanation/Reference:
QUESTION 2
Which of the following authentication methods are supported for Telnet users? (Choose three)
A. Password authentication
B. AAA local authentication
C. MD5 authentication
D. No authentication
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 3
On Huawei AR G3 Series routers, which authentication modes does AAA support? (Choose all that apply.)
A. None
B. Local
C. Radius
D. 802.1X
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 4
Jul 24, 2019

Refer to the configuration output. RTA has been configured using AAA as shown, and associated with the
“huawei” domain. For users in the huawei domain, which authentication-scheme will be used?
A. au1
B. au2
C. au1 will be used. When au1 is deleted, users will use au2
D. au2 will be used. When au2 is deleted, users will use au1
Correct Answer: B
Section: (none)
Explanation
QUESTION 5
A user accesses a server supporting AAA, for which the authorization mode on the AAA server has been
configured using the command “authorization-mode hwtacacs if-authenticated”.
Which of the following statements regarding this command are true? (Choose three).
A. If the hwtacacs server fails to respond, the user will be authenticated using local authentication.
B. If the hwtacacs server fails to respond, the user will be authenticated using remote authentication.
C. If the hwtacacs server fails to respond, the user will bypass authentication.
D. The hwtacacs server will authorize the user.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 6
Which of the following descriptions regarding eSight is not correct?
A. eSight is used to monitor and manage enterprise networks.

B. eSight supports only Huawei devices.
C. eSight supports WLAN management and monitoring of hotspot coverage.
D. eSight supports the backup of configuration files and network traffic analysis.
Correct Answer: B
Section: (none)
Explanation
QUESTION 7
Jul 24, 2019

What of the following statements is correct regarding access control list types and ranges?
A. A basic ACL value ranges from 1000-2999

B. An advanced ACL value ranges from 3000-4000
C. A layer 2 ACL value ranges from 4000-4999
D. An interface ACL value ranges 1000-2000
Correct Answer: C
Section: (none)
Explanation
QUESTION 8
Which of the following parameters is not used by Advanced ACL?
A. Source interface
B. Destination port number
C. Protocol number
D. Time-range
Correct Answer: A
Section: (none)
Explanation
QUESTION 9
Refer to the configuration output. Which of the following statements regarding ACL 2001 is correct?
A. Packets from network 10.0.1.0/24 network will be denied.

B. Packets from network 10.0.1.0/24 network will be permitted.
C. Packets destined for network 10.0.1.0/24 will be denied.
D. Packets destined for network 10.0.1.0/24 will be permitted.
Correct Answer: B
Section: (none)
Explanation
QUESTION 10
Refer to the configuration output. A network administrator configured the ACL on router RTA, as shown.
Jul 24, 2019

Which of the following statements regarding the rule order are correct? (Choose two).
A. The rule-number of the first rule is 1

B. The rule-number of the first rule is 5
C. The rule-number of the second rule is 2
D. The rule-number of the second rule is 10
Correct Answer: BD
Section: (none)
Explanation
QUESTION 11
Following a failure of services in the network, an administrator discovered that the configuration in one of the
enterprise routers had been changed.
What actions can be taken by the administrator to prevent further changes? (Choose three)
A. The administrator should limit access by setting the login privilege of users to 0.
B. The administrator should configure AAA to manage user authorization on the router.
C. The administrator should configure an ACL to allow only the administrator to manage the router.
D. The administrator should configure port-security on the router.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 12
Refer to the configuration output. Which of the following statements is correct regarding the configuration of the
ACL on RTA?
A. Packets from network 20.1.1.0/24 network will be denied.

B. Packets from network 20.1.1.0/24 network will be permitted.
C. Packets destined for network 20.1.1.0/24 will be denied.
D. Packets destined for network 20.1.1.0/24 will be permitted.
Correct Answer: A
Section: (none)
Explanation
QUESTION 13
Jul 24, 2019

Refer to the configuration output. Which of the following statements are correct regarding the configuration of
the ACL on RTA? (Choose two).
A. Packets from network 172.16.1.1/32 will be denied.

B. Packets from network 172.16.1.0/24 will be denied.
C. Packets from network 172.17.1.0/24 will be denied.
D. Packets from network 172.18.0.0/16 will be denied.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 14
The network administrator wants to improve the performance of network transmission, what steps can the
administrator take? (Choose two)
A. Change the work mode to full duplex of each end station.

B. Link the end stations together using a switch.
C. Change the work mode to half duplex of each end station.
D. Link the end stations together using a hub.
Correct Answer: AB
Section: (none)
Explanation
QUESTION 15
On Huawei switch, which of the following commands can be used to set port duplex mode as "auto
Jul 24, 2019

negotiation"? (Choose two)
A. duplex negotiation auto

B. duplex auto-negotiation
C. duplex auto
D. undo duplex
Correct Answer: CD
Section: (none)
Explanation
QUESTION 16
The network administrator wishes to transmit data between two end stations. The network interface cards of
both devices operates at 100Mbps however one supports half duplex while the other uses full duplex mode.
What will occur as a result?
A. The end stations cannot communicate.

B. The end stations can communicate, but data may be lost during transmission of large amounts of traffic.
C. The end stations will operate normally
D. The end stations can communicate, but speed is different during transmission of large amounts of traffic.
Correct Answer: B
Section: (none)
Explanation
QUESTION 17
An Ethernet port can work one of three duplex modes, whereas an Optical Ethernet port only supports one
single mode.
Which of the following represents this mode?
A. Full-duplex
B. Half-duplex
C. Auto-negotiation
D. Simplex
Correct Answer: A
Section: (none)
Explanation
QUESTION 18
While inspecting packets in the network, a network administrator discovers a frame with the destination MAC
address of 01-00-5E-A0-B1-C3.
What can the administrator determine from this?
Jul 24, 2019

A. The MAC address is a unicast address.
B. The MAC address is a broadcast address
C. The MAC address is a multicast address.
D. The MAC address is incorrect.
Correct Answer: C
Section: (none)
Explanation
QUESTION 19
According to OSI reference model, which layer is responsible for end to end error checking and flow control?
A. Physical layer
B. Data link layer
C. Network layer
D. Transport layer
Correct Answer: D
Section: (none)
Explanation
QUESTION 20
Which of the following mechanisms are used for flow control? (Choose three)
A. Acknowledgement
B. Buffering
C. Source quench messages
D. Windowing
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 21
Refer to the capture output. The administrator has captured three packets in the network. Which statement
regarding the captured packets is incorrect?
A. This packets represent a TCP three-way handshake process.

B. 10.0.12.1 is the telnet server, while 10.0.12.2 is the telnet client.
Jul 24, 2019

C. The three packets contain no application data.
D. 10.0.12.1 uses port 50190 to buid the telnet connection.
Correct Answer: B
Section: (none)
Explanation
QUESTION 22
An Ethernet frame is captured by network protocol analyzer tool and the value of Type/Length field is 0x0800.
Which of the following statements about the frame are correct? (Choose two)
A. The frame structure of the frame is Ethernet_II

B. The frame structure of the frame is 802.3
C. Its upper layer protocol is IP
D. Its upper layer protocol is IPX
Correct Answer: AC
Section: (none)
Explanation
QUESTION 23
Which of the following descriptions regarding the TTL field of the IP packet is correct?
A. The TTL defines how many packets the source can send.
B. The TTL defines the duration during which the source can send packets.
C. The TTL value will decrement by 1 each time the packet is routed.
D. The TTL value will increment by 1 each time the packet is routed.
Correct Answer: C
Section: (none)
Explanation
QUESTION 24
Which of the following statements are correct about TTL field in IP packet? (Choose two)
A. The maximum value of TTL is 65535.

B. Normally, it's impossible for a router to receive a packet whose TTL is zero.
C. The main purpose of TTL is to prevent IP packets from circulating endlessly in a network which can
consume a lot of bandwidth.
D. TTL value will be decremented as a packet is passed through the network devices such as hub, LAN switch
and router.
Correct Answer: BC
Section: (none)
Explanation
Jul 24, 2019

QUESTION 25
In the case of Huawei router, what is the "-i" parameter in a Ping command issued on a VRP operating system
used to set?
A. Interface for sending an Echo Request packet

B. Source IP address for sending an Echo Request packet
C. Interface for receiving an Echo Reply packet
D. Destination IP address for receiving an Echo Reply packet
Correct Answer: A
Section: (none)
Explanation
QUESTION 26
To provide the information about the IP addresses that a user packet traverses along the path to the
destination, which of the following does Tracert record in each expired ICMP TTL packet?
A. Destination port
B. Source port
C. Destination IP address
D. Source IP address
Correct Answer: D
Section: (none)
Explanation
QUESTION 27
Which of the following statements regarding the verification of IP connectivity are false? (Choose three)
A. The ping 127.0.0.1 command can be used to check whether the network cable is correctly inserted into the
host’s Ethernet port.
B. The ping command with the host IP address as the destination can be used to verify that the TCP/IP
protocol suite is functioning correctly.
C. The ping command can be used to verify connectivity between the host and the local gateway.
D. The command “ipconfig /release” can be used to check connectivity problems between the host and the
local gateway.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 28
A network administrator uses the ping command to check for points of failure in the network.
Jul 24, 2019

Which protocols will be used during this process? (Choose two)
A. ICMP
B. TCP
C. ARP
D. UDP
Correct Answer: AC
Section: (none)
Explanation
QUESTION 29
A network administrator recently used tracert to trace the path to the destination IP address of an external
website, however the trace path displayed only a timeout result.
Which of the following statements correctly explains the reason for this? (Choose two)
A. The source router had shutdown the ICMP function.

B. This destination IP address does not exist.
C. The gateway cannot find a route to the destination.
D. This is a normal phenomenon.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 30
A network administrator uses the ping command to test connectivity to the destination 10.0.0.2 on a Huawei AR
series router.
Which statement regarding the output is correct?
A. The network administrator used the command ping -c 2 -s 800 10.0.0.2

B. The network administrator used the command ping -a 2 -v 800 10.0.0.2
C. The path between the source and destination is not OK.
D. The network administrator changed the default TTL value.
Correct Answer: A
Jul 24, 2019

Section: (none)
Explanation
QUESTION 31
Which of the following statements explains the behavior of the ICMP redirect function? (Choose two)
A. When a router receives data on the interface via which the same data needs to be forwarded, and the
source is on the same segment as the next hop, an ICMP redirect message will be sent by the router to the
source.
B. When a router receives data on an interface, and the router’s IP address matches the destination IP of the
data, an ICMP redirect message will be sent by the router to the source.
C. When a router receives data on the interface via which the same data needs to be forwarded, and the
source is on the same segment as the next hop, an ICMP Redirect message will be sent by the source to
the router.
D. When a router receives data on the interface via which the same data needs to be forwarded, and the
source is on a different segment from the next hop, an ICMP redirect message will be sent by the router to
the source
Correct Answer: AD
Section: (none)
Explanation
QUESTION 32
Host A wishes to send data to host C, and generates an ARP request to obtain the destination MAC address.
Jul 24, 2019

Which statement is true?
A. The destination IP address of the ARP request is Host C.

B. The destination MAC address of this ARP request is Host C.
C. The destination IP address for the ARP request is a broadcast IP address.
D. The destination MAC address of this frame is the MAC address of G0/0/0 on RTA.
Correct Answer: A
Section: (none)
Explanation
QUESTION 33
An ARP request is sent by host A to obtain the destination MAC address of host D.
Which statement is true about regarding the ARP reply?
A. The destination MAC address of this frame is the MAC address of Switch A.
B. The destination IP address of this packet is the VLANIF1 IP address of Switch A.
C. The destination MAC address of this frame is the MAC address of Host A.
D. The destination IP address of this packet is a broadcast IP address.
Correct Answer: C
Section: (none)
Jul 24, 2019

Explanation
QUESTION 34
Which of the following applications can be used to detect the path along which the data packets are transmitted
from the source to the destination?
A. Route
B. Netstat
C. Tracert
D. Send
Correct Answer: C
Section: (none)
Explanation
QUESTION 35
How many probe packets are sent for each TTL value by default when "tracert" is used to detect the path along
which packet is sent from source to destination?
A. 3
B. 4
C. 6
D. 8
Correct Answer: A
Section: (none)
Explanation
QUESTION 36
Which of the following types can ICMP packets be classified into? (Choose two)
A. ICMP transport packet

B. ICMP error reporting packet
C. ICMP query packet
D. ICMP application packet
Correct Answer: BC
Section: (none)
Explanation
QUESTION 37
On VRP platform, which of the following parameters can be used together with the "ping" command to specify
the source address of an echo request message?
Jul 24, 2019

A. -a
B. -s
C. -d
D. -n
Correct Answer: A
Section: (none)
Explanation
QUESTION 38
A router functioning as a Proxy receives an ARP request packet, but finds that the destination address in the
packet is not intended for itself. In this case, what will the router do? (Choose two)
A. Discard the packet.

B. Check for a route that matches the destination address.
C. Forward its MAC address to the ARP request sender after finding that a route to the destination address is
available.
D. Broadcast the ARP request packet.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 39
Two end stations in a point-to-point network perform address resolution.
Which of the following statements is correct?
A. The destination address of an ARP request from each station will be a unicast MAC address.
B. The destination address of an ARP request from each station will be a broadcast IP address.
C. The destination address of an ARP reply from each station will be a unicast MAC address.
D. The destination address of an ARP reply from each station will be a broadcast MAC address.
Correct Answer: C
Section: (none)
Explanation
QUESTION 40
What will the destination MAC address be at the moment a frame is transmitted by the host, when the router is
the IP destination?
A. The MAC address of the switch.

B. The MAC address of the router interface G0/0/0.
C. The MAC address of the host.
D. The destination MAC address will be a broadcast MAC address.
Jul 24, 2019

Correct Answer: D
Section: (none)
Explanation
QUESTION 41
Which of the following statements about gratuitous ARP packets are true? (Choose two)
A. A system can determine whether conflicting IP addresses are used by sending a gratuitous ARP packet
B. A gratuitous ARP packet uses the same format as an ARP request packet.
C. A gratuitous ARP packet can help to update an IP address.
D. A gratuitous ARP packet uses the same format as an ARP reply packet.
Correct Answer: AB
Section: (none)
Explanation
QUESTION 42
UDP is connectionless oriented, which of the following must be used in order to ensure reliability?
A. Internet Protocol
B. Application Layer Protocol
C. Network Layer Protocol
D. Transmission Control Protocol
Correct Answer: B
Section: (none)
Explanation
QUESTION 43
Refer to the graphic.
The administrator has configured an IP address for Host A and Host B, but had forgotten to configure a default
gateway.
Jul 24, 2019

What effect will this have on the hosts?
A. Neither host will be affected, and therefore will be able to communicate with the peer.
B. Host A will be unable to connect to the router’s G0/0/0 interface.
C. Hosts will be unable to communicate unless arp-proxy is enabled on the router.
D. The host will be unable to reach neither the local nor remote network destinations.
Correct Answer: C
Section: (none)
Explanation
QUESTION 44
A host has established a telnet connection with the router attached to interface G0/0/0.
Which of the following statements are correct? (Choose all that apply.)
A. The destination MAC address of a frame sent by the host will be the MAC address of the router interface
G0/0/0.
B. The destination MAC address of a frame sent by the host will be the MAC address of the switch.
C. The destination port number in a segment header will have a value of 80.
D. The destination IP address of a packet will be the IP address of the Router interface G0/0/0.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 45
Jul 24, 2019

The administrator uses the ping command on the host to test connectivity to the website www.huawei.com.
The command line shows a request time out. The administrator displays the ARP entries for the host.
Which entry will be found in the ARP cache table of the host?
A. The MAC address of the destination www.huawei.com will exist in the ARP cache.
B. The MAC address of the switch will exist in the ARP cache.
C. The IP address of the destination www.huawei.com will exist in the ARP cache.
D. The MAC address of router interface G0/0/0, will exist in the ARP cache.
Correct Answer: D
Section: (none)
Explanation
QUESTION 46
When R2 forwards data to R3 from R1, which of the following items will change? (Choose two)
A. The source MAC address

B. The destination MAC address
C. The source IP address
D. The destination IP address
Correct Answer: AB
Section: (none)
Explanation
QUESTION 47
If Host B also configured the IP address as “192.168.1.1/24”, an IP address config will occur.
What will happen as a result?
A. Host B will send an ICMP request to the destination with the configured IP address. If a reply is received,
the host will notify of an address conflict.
B. Host A will send a gratuitous ARP request to resolve the MAC address of the destination 192.168.1.1, for
which Host B will reply.
C. Host B will send a gratuitous ARP request to resolve the MAC address of the destination 192.168.1.1, for
which Host A will reply.
D. Host A will ignore any received ARP request intended for destination 192.168.1.1.
Correct Answer: C
Section: (none)
Explanation
QUESTION 48
Jul 24, 2019

Refer to the graphic. A switch attempts to forward a frame to the MAC destination 5489-98ec-f011. What
operation will occur on the switch?
A. The switch will send a request to obtain the MAC address of 5489-98ec-f011.
B. The switch will report that the destination is unreachable and report this to the source.
C. The switch will flood the frame via all ports, with exception of the port on which the frame was received.
D. The switch will drop the frame because it does not have an entry in its MAC address table.
Correct Answer: C
Section: (none)
Explanation
QUESTION 49
Host A has been connected to switch A and configured with an IP address.
When Host A initially forwards a frame, what action will be taken by Switch A?
A. Switch A will drop this frame.

B. Switch A will attempt to flood the frame to all ports except for the G0/0/1 interface.
C. Switch A will forward the frame via ports G0/0/1, G0/0/2 and G0/0/3.
D. Switch will receive this frame before returning the frame to G0/0/1.
Correct Answer: B
Section: (none)
Explanation
QUESTION 50
A server is linked to port interface G0/0/1 of a switch. The administrator wishes to allow only this server to be
linked to this interface on the switch.
Which method can be used to achieve this?
A. Configure a static ARP entry using the server’s IP address and MAC address in the switch.
B. Configure a static MAC address binding entry of the server’s MAC address and the interface in the switch.
C. Configure the default gateway of the switch to be the same as the server’s IP address.
D. It is not possible to enable a single device to be associated with an interface.
Correct Answer: B
Jul 24, 2019

Section: (none)
Explanation
QUESTION 51
An administrator connects two switches together in a local enterprise network. The ports of one switch support
Fast Ethernet, while the ports of the other switch support Gigabit Ethernet. Hosts connected to one switch are
able to communicate, however communication between the two switches fails.
What is the possible reason for this?
A. The ports have disabled auto-negotiation.

B. One port is supporting auto-negotiation, while auto-negotiation is disabled on the port of the other switch.
C. The port of one switch is operating using half duplex mode, while the port of the other switch is using full
duplex mode.
D. A Fast Ethernet port cannot communicate directly with a Gigabit Ethernet port.
Correct Answer: A
Section: (none)
Explanation
QUESTION 52
A layer 2 LAN switch generates CAM table entries according to the ( ) of the received frame.
A. Source MAC address

B. Destination MAC address
C. Source IP address
D. Destination IP address
Correct Answer: A
Section: (none)
Explanation
QUESTION 53
Which of the following statements about collision domains and broadcast domains are correct? (Choose three)
A. Devices connected to the same hub form a collision domain

B. Devices connected to the same hub form a broadcast domain
C. Devices connected to the same bridge form a collision domain
D. Devices connected to the same bridge form a broadcast domain
E. Devices connected to the same router form a broadcast domain
Correct Answer: ABD

Section: (none)
Explanation
Jul 24, 2019

QUESTION 54
Which of the following statements regarding layer-2 switch is incorrect?
A. The switch learns MAC addresses automatically.

B. The layer-3 header is modified before the received packet is transmitted.
C. The layer-2 header is modified before the received packet is transmitted.
D. The layer-2 LAN switch operates at data link layer.
Correct Answer: B
Section: (none)
Explanation
QUESTION 55
Refer to the display output. What can be determined based on the output of the display command?
A. Interface Gigabit Ethernet 0/0/0 is connected to a wrong cable

B. Interface Gigabit Ethernet 0/0/0 is not associated with an IP address
C. Interface Gigabit Ethernet 0/0/0 is not associated with a dynamically defined route.
D. Interface Gigabit Ethernet 0/0/0 has been manually shut down by an administrator.
Correct Answer: D
Section: (none)
Explanation
QUESTION 56
Which of the following statements regarding static and dynamic routing is incorrect?
A. The static route can be easily configured and managed on the enterprise network.
B. The use of dynamic routing is more convenient for the administrator to manage the network following
network convergence.
C. The static route can automatically recover when a link failure is encountered.
D. Dynamic routing will use more resources than static routes.
Correct Answer: C
Section: (none)
Explanation
QUESTION 57
Which of the following are routed protocols? (Choose all that apply.)
A. IP
Jul 24, 2019

B. OSPF
C. BGP
D. IPX
Correct Answer: AD
Section: (none)
Explanation
QUESTION 58
Which of the following statements regarding the routing table are correct? (Choose all that apply.)
A. The next hop in the routing table is redundant because the outgoing interface can be used for packet
forwarding.
B. The routes from generated by different protocols have different preferences.
C. The metrics of different routing protocols are comparable.
D. The metrics of different routing protocols are not comparable
Correct Answer: BD
Section: (none)
Explanation
QUESTION 59
Which of the following commands can be used to display the routing table on a Quidway router?
A. display ip path
B. display ip routing-table
C. display interface
D. display current-configuration
Correct Answer: B
Section: (none)
Explanation
QUESTION 60
Which of the following entries is not included in the routing table?
A. source address
B. next hop
C. destination address
D. cost
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 61
Which of the following problems are caused by routing loops? (Choose three)
A. Slow convergence
B. Packets circulate between routers
C. Router restarting
D. Inconsistency of routing information
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 62
An administrator wishes to manage the router in the remote branch office, which method can be used?
A. Telnet
B. FTP
C. Console Connection
D. DHCP
Correct Answer: A
Section: (none)
Explanation
QUESTION 63
The administrator cannot use telnet to manage the AR2200. The administrator is able to verify connectivity to
the router and has been informed that other administrators have no difficulties using telnet.
Which statements describe the possible reasons for this problem? (Choose all that apply.)
A. The user’s status has been blocked

B. The user’s privilege level has been changed to 0.
C. The user has been deleted.
D. The telnet service in the AR2200 router has been disabled.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 64
A user logged into a VRP supported device through telnet, but when attempting to configure the device, found
that he is unable to use the system-view command to enter the system-view.
What are the possible reasons for this? (Choose two)
Jul 24, 2019

A. The device’s VTY interface only provides permission for some telnet users to run the system-view
command.
B. The user’s telnet software restricts use of this command.
C. The user’s privilege level is lower than the level associated with the system-view command.
D. The system-view command privilege level is lower than the level associated with the user.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 65
The users who log on the router through Telnet are not permitted to configure IP address.
What is the possible reason?
A. Communication failures occur between the user and the router.

B. The authentication mode of Telnet is set incorrectly.
C. Privilege level of Telnet is set incorrectly.
D. SNMP parameters are set incorrectly.
Correct Answer: C
Section: (none)
Explanation
QUESTION 66
Which of the following statements are correct? (Choose two)
A. A single collision domain exists between RTA and SWC.

B. A single broadcast domain exists between SWA and SWB.
Jul 24, 2019

C. A single collision domain exists between SWA and SWC.
D. A single broadcast domain exists between SWA and SWC.
Correct Answer: CD
Section: (none)
Explanation
QUESTION 67
On the interface serial 1/0/1 of RTA, the command “ip address unnumbered interface loopback 0” has been
configured.
Which following statements are correct? (Choose two).
A. The IP address of interface serial 1/0/1 is 10.1.1.1/24

B. The IP address of interface serial 1/0/1 is 10.1.1.1/32
C. The route entry 10.1.1.0/24 exists in RTA’s routing-table
D. The route entry 10.1.1.0/24 does not exist in RTA’s routing-table
Correct Answer: BD
Section: (none)
Explanation
QUESTION 68
Jul 24, 2019

The host has a problem establishing a telnet connection with the router attached to interface G0/0/0. Which of
the following steps can be used to help the administrator identify the problem? (Choose two)
A. Check whether the host has configured the gateway IP address.

B. Check whether the switch has configured the gateway IP address.
C. Use the ping tool to check connectivity between host and router.
D. Check the telnet server configuration is right on the router.
Correct Answer: CD
Section: (none)
Explanation
QUESTION 69
Which of the following methods are supported by VRP platform to configure the router? (Choose three)
A. Through the Console port

B. Through Telnet
C. Through the AUX port
D. Through FTP
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 70
The administrator wishes to update the configuration file of an AR2200 router using a USB cable.
Jul 24, 2019

How can this be achieved? (Choose all that apply.)
A. The administrator should connect the USB cable between the terminal and the mini USB port of the AR2200
router.
B. The administrator should connect the USB cable between the terminal and the USB port of the AR2200
router.
C. The AR2200 router cannot support configuration updates through a USB cable.
D. The administrator should install the mini USB drivers on the terminal after connecting the USB.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 71
The administrator wishes to manage a network through telnet from a user's terminal to a router.
How can this be achieved?
A. A connection should be established between the ethernet port of the terminal and the console port of the
router.
B. A connection should be established between the ethernet port of the terminal and the ethernet port of the
router.
C. A connection should be established between the console port of the terminal and the ethernet port of the
router.use console cable connect pc’s ethernet port and router’s console port.
D. A connection should be established between the COM port of the terminal and the console port of the
router.
Correct Answer: B
Section: (none)
Explanation
QUESTION 72
Whilst configuring a device, an administrator experiences trouble remembering certain commands.
Which of the following will help support the administrator? (Choose two)
A. TAB
B. question mark
C. ctrl+b
D. ctrl+c
Correct Answer: AB
Section: (none)
Explanation
QUESTION 73
Jul 24, 2019

Refer to the configuration output. The administrator configured the device using the commands in the
configuration output. Regarding these commands, which statement is false?
A. The administrator wishes to enable management through the console interface.

B. Following configuration, the administrator cannot manage the device remotely.
C. A user that logs-in through the console interface is assigned the highest privilege level.
D. The password of a user logged in through console is ‘cipher huawei2012’.
Correct Answer: D
Section: (none)
Explanation
QUESTION 74
Which of the following is abbreviation of VRP?
A. Versatile Routine Platform

B. Virtual Routing Platform
C. Virtual Routing Plane
D. Versatile Routing Platform
Correct Answer: D
Section: (none)
Explanation
QUESTION 75
Which of the following must be used to establish the configuration environment when a router is powered on for
the first time?
A. SSL
B. SSH
C. Console port
D. Telnet
Correct Answer: C
Section: (none)
Explanation
QUESTION 76
Jul 24, 2019

Which of the following parameter settings for terminal emulation are correct when configuring a Huawei router
through the Console port?
A. 4800bps, 8 data bits,1 stop bits, odd parity check, and no flow control
B. 9600bps, 8 data bits, 1 stop bits, no parity check, and no flow control
C. 9600bps, 8 data bits, 1 stop bits, even parity check, and hardware flow control
D. 19200bps, 8 data bits, 1 stop bits, no parity check, and no flow control
Correct Answer: B
Section: (none)
Explanation
QUESTION 77
Which of the following commands is used to enter the system-view from the user view on a Huawei router?
A. system-view
B. enable
C. configure terminal
D. interface system
Correct Answer: A
Section: (none)
Explanation
QUESTION 78
On VRP platform, the command lines are classified into four levels in increasing priority: Visit level, Monitoring
level, Configuration level, and Management level. At which level, the operator is permitted to configure service
but is not permitted to operate the file system?
A. Visit level
B. Monitoring level
C. Configuration level
D. Management level
Correct Answer: C
Section: (none)
Explanation
QUESTION 79
On Huawei VRP platform, which of the following can be used to invoke the history command saved by the
command line interface? (Choose two)
A. Up cursor key < >

B. Left cursor key < >
C. Ctrl+P
D. Ctrl+U
Jul 24, 2019

Correct Answer: AC
Section: (none)
Explanation
QUESTION 80
Which of the following commands can be used to view the current configurations on a Huawei router?
A. display current-configuration
B. display saved-configuration
C. view saved-configuration
D. show startup-configuration
Correct Answer: A
Section: (none)
Explanation
QUESTION 81
The administrator wishes to change name of the router. Under which view should the administrator be in order
to achieve this?
A. User-view
B. System-view
C. Interface-view
D. Protocol-view
Correct Answer: B
Section: (none)
Explanation
QUESTION 82
<Huawei> system-view
[Huawei]command-privilege level 3 view user save
Refer to the command output. What is the result of the shown command?
A. The command adjusts the save command of a user to privilege level 3.

B. The command adjusts the save command in the user view to privilege level 3.
C. The command adjusts the user view command privilege level to 3, and saves the configuration.
D. The command adjusts the privilege level of a user to 3, and saves the configuration.
Correct Answer: B
Section: (none)
Explanation
Jul 24, 2019

QUESTION 83
<Huawei>system-view
[Huawei]history-command max-size 20
Refer to the command output. Which statements regarding the shown command are true? (Choose two)
A. The command is used to adjust the size of the history command buffer.
B. The default value of the history command buffer is 5.
C. The command should be configured in the user-interface view.
D. Once configured, commands totaling up to 20 bytes can be saved in the buffer.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 84
An AR2200 router is required to be reconfigured from scratch. Which steps are needed to achieve this?
(Choose all that apply.)
A. Reset the saved configuration.

B. Clear the current configuration.
C. Reboot the AR2200.
D. Assign the configuration file to be used at next startup.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 85
An administrator has been requested to replace the configuration file of a router in the network. The
administrator has been instructed that after logging into the router, he must first permanently erase the current
configuration file config.zip from the system.
Which command should he use to achieve this?
A. delete /force config.zip

B. delete /unreserved config.zip
C. reset config.zip
D. clear config.zip
Correct Answer: B
Section: (none)
Explanation
QUESTION 86
Which of the following commands can switch a view from the system view to the user view?
Jul 24, 2019

A. System-view
B. Router
C. Quit
D. User-view
Correct Answer: C
Section: (none)
Explanation
QUESTION 87
Which of the following storage devices are supported by Huawei router? (Select four)
A. SDRAM
B. NVRAM
C. Flash
D. Hard Disk
E. CF Card
Correct Answer: ABCE

Section: (none)
Explanation
QUESTION 88
Which of the following storage devices is used to store the startup configuration files in a router?
A. SDRAM
B. NVRAM
C. Flash
D. BootROM
Correct Answer: B
Section: (none)
Explanation
QUESTION 89
<Huawei>reset saved-configuration
Warning: The action will delete the saved configuration in the device.
The configuration will be erased to reconfigure. Continue? [Y/N]:
Refer to the configuration output. Which of the following statements are true? (Select two answers)
A. A user should enter ‘Y’ when wishing to clear the saved configuration file.
B. The saved-configuration file that the device starts with can be erased.
C. The saved-configuration will be deleted after typing N
D. The saved-configuration file will be replaced with the current-configuration.
Jul 24, 2019

Correct Answer: AB
Section: (none)
Explanation
QUESTION 90
When a router is powered on, the router reads the configuration file saved in the default save directory to get
itself initialized. If the configuration file does not exist in the default save directory, what does the router use to
initialize itself?
A. New configuration file

B. Initial configuration file
C. Default parameters
D. Current configuration file
Correct Answer: C
Section: (none)
Explanation
QUESTION 91
Refer to the display output. Which statement is false?
A. The current configuration file has not been saved.

B. The current startup system software is ar2220-v200r003c00spc200.cc
C. The next startup system software cannot be changed.
D. The next startup system software can be changed by using the “startup system software <startup-
softwarename>.cc” command.
Correct Answer: C
Section: (none)
Explanation
Jul 24, 2019

QUESTION 92
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform configurations
when Auto-Config is running, the DHCP, routing, DNS, and VTY configurations will be lost. Do you want to stop
Auto-Config? [y/n]:
When an administrator first initializes the router, a warning is displayed. Which statement regarding this
warning is correct?
A. If Auto-Config is required, the administrator should select ‘y’.

B. If Auto-Config is not required, the administrator should select ‘n’, for which subsequent configuration of the
DHCP server, routing, DNS server and VTY user configuration is lost.
C. When a device is started for the first time, the Auto-Config function is active.
D. When a device is started for the first time, the Auto-Config function is inactive.
Correct Answer: C
Section: (none)
Explanation
QUESTION 93
An AR2200 router in the company network cannot boot. In order to resolve this, the administrator wishes to
update the VRP software.
What should he/she do?
A. The administrator should use a console cable to connect the router and host, and directly upgrade the
device.
B. The administrator should use FTP to transfer the VRP software, by configuring the AR2200 router as an
FTP client.
C. The administrator should use DHCP to boot the AR2200, and then use the AR2200 router as a TFTP client
to download the VRP software from the server.
D. The administrator should use the telnet command on the client to remote access the device, and upgrade
the VRP software.
Correct Answer: B
Section: (none)
Explanation
QUESTION 94
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform configurations
when Auto-Config is running, the DHCP, routing, DNS, and VTY configurations will be lost. Do you want to stop
Auto-Config? [y/n]:
Refer to the output. When the administrator first starts the router, a system notice is displayed, however after
rebooting this router, the notice disappeared. What is the reason for this? (Choose all that apply.)
A. This notice only appears during the very first device startup.
Jul 24, 2019

B. The administrator has configured the device and saved the configuration, causing the notice to disappear.
C. The administrator selected ‘n’ and did not save the configuration.
D. The administrator selected ‘y’ and saved the configuration.
Correct Answer: BD
Section: (none)
Explanation
QUESTION 95
An end system is unable to communicate with a DHCP server following the startup process.
Which IP address may be used by the client?
A. 0.0.0.0
B. 127.0.0.1
C. 169.254.2.33
D. 255.255.255.255
Correct Answer: C
Section: (none)
Explanation
QUESTION 96
Refer to the configuration output. The administrator wishes to configure the DHCP server pool in order to
assign an IP address to the customer’s terminal device.
Which command should be included in the configuration to provide the minimal lease period for IP addresses?
A. dhcp select relay

B. lease day 1
C. lease 24
D. lease 0
Correct Answer: B
Section: (none)
Explanation
QUESTION 97
A DHCP server has been established in the enterprise network. After the client has obtained an IP address
from the DHCP server, the user decided to modify the IP address manually.
Jul 24, 2019

In what way may this affect the enterprise network? (Choose two).
A. The client may experience an IP address conflict.

B. The client may access the network normally.
C. The client’s interface connection will shutdown.
D. The client will associate with another DHCP server.
Correct Answer: AB
Section: (none)
Explanation
QUESTION 98
A DHCP server in the enterprise network is being used to allocated IP addresses to hosts. An administrator
discovers however that some hosts are obtaining IP addresses outside of the scope of the DHCP server’s
address pool.
What are the possible reasons for this? (Choose three).
A. Another DHCP server exists in the network and is allocating IP addresses to hosts that happen to be within
a closer proximity than the authorized DHCP server.
B. The hosts were unable to discover a DHCP server and therefore generated their own address in the
169.254.0.0 address range.
C. The hosts were unable to discover a DHCP server and therefore generated their own address in the
127.254.0.0 address range.
D. All addresses from the DHCP pool have been assigned.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 99
Refer to the configuration output. Following configuration, a host is connected to the interface Gigabit Ethernet
0/0/1 of the router. Which IP address will the client obtain?
A. An IP address from network 10.10.10.0/24 will be assigned.
Jul 24, 2019

B. An IP address from network 10.20.20.0/24 will be assigned.
C. The host will be unable to obtain an IP address.
D. An IP address may be assigned from either 10.10.10.0/24 or 10.20.20.0/24.
Correct Answer: A
Section: (none)
Explanation
QUESTION 100
The IP addresses of clients in the network are deployed via a DHCP server. When a host reboots, which
message will the host first send to the DHCP server?
A. DHCP DISCOVER
B. DHCP REQUEST
C. DHCP OFFER
D. DHCP ACK
Correct Answer: B
Section: (none)
Explanation
QUESTION 101
A DHCP Unique Identifier (DUID) in DHCPv6 can be configured in VRP using which formats? (Choose two).
A. DUID-LL
B. DUID-LLT
C. DUID-EN
D. DUID-LLC
Correct Answer: AB
Section: (none)
Explanation
QUESTION 102
Which of the following statements about the information contained in a Database Description packet are true?
(Choose three)
A. A Database Description packet contains all information about each LSA.

B. A Database Description packet contains only the header of an LSA.
C. The header of an LSA is the unique identifier of the LSA.
D. The header of an LSA is only a small portion of all the data of the LSA.
Correct Answer: BCD

Section: (none)
Explanation
Jul 24, 2019

QUESTION 103
What is the default authentication mode for the default_admin domain?
A. None
B. Local
C. Radius
D. 802.1X
Correct Answer: B
Section: (none)
Explanation
QUESTION 104
How many domains can be configured on a Huawei router?
A. 30
B. 31
C. 32
D. 33
Correct Answer: A
Section: (none)
Explanation
QUESTION 105
An authenticator router has been configured with two domains named “Area1” and “Area2”, following which a
user is created with the username “huawei” and the password ”hello” for authentication. Which domain does
this user belongs to?
A. Area1 domain
B. Area2 domain
C. default domain
D. default_admin domain
Correct Answer: C
Section: (none)
Explanation
QUESTION 106
In order to check if the interface serial 1/0/0 is working in either DCE or DTE mode, command ( ) is used.
A. display mode serial 1/0/0

B. display controller
Jul 24, 2019

C. display interface serial 1/0/0
D. display current-config
Correct Answer: C
Section: (none)
Explanation
QUESTION 107
How is mapping performed on a DTE device in a Frame Relay network?
A. The local DLCI number is mapped to a remote IP address.

B. The local IP address is mapped to a remote DLCI number.
C. The local DLCI number is mapped to a local IP address.
D. The remote DLCI number is mapped to a remote IP address.
Correct Answer: A
Section: (none)
Explanation
QUESTION 108
If Frame Relay implements dynamic address mapping for the PVC, which protocol will be used?
A. LMI protocol
B. ARP protocol
C. RARP protocol
D. InARP protocol
Correct Answer: D
Section: (none)
Explanation
QUESTION 109
Which command should be used to check the mapping between protocol addresses and frame relay
addresses?
A. display fr interface
B. display fr map-info
C. display fr inarp-info
D. display interface brief
Correct Answer: B
Section: (none)
Explanation
Jul 24, 2019

QUESTION 110
Which of the following protocols is used in Frame Relay to map the address to DLCI dynamically?
A. ARP protocol
B. RARP protocol
C. InARP protocol
D. Map protocol
Correct Answer: C
Section: (none)
Explanation
QUESTION 111
Which of the following parameters must be specified when configuring static mapping for Frame Relay
network? (Choose two)
A. Local DLCI
B. Remote DLCI
C. Local network layer protocol address
D. Remote network layer protocol address
Correct Answer: AD
Section: (none)
Explanation
QUESTION 112
Which of the following regarding Frame Relay DLCI are correct? (Choose three)
A. DLCI is locally significant

B. DLCI is allocated by DTE
C. The range of DLCI value that can be used is from 16-1007
D. The same DLCI can be configured on different physical interfaces
Correct Answer: ACD

Section: (none)
Explanation
QUESTION 113
Which of the following commands is used to enable dynamic address mapping protocol in the interface
encapsulated with Frame Relay?
A. fr inarp
B. fr reverse-arp
C. inverse-arp
D. reverse-arp
Jul 24, 2019

Correct Answer: A
Section: (none)
Explanation
QUESTION 114
What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?
A. remote logical channel ID

B. local DLCI
C. remote interface ID
D. remote node ID
Correct Answer: B
Section: (none)
Explanation
QUESTION 115
Which of the following commands can be used to display mapping relationship between network address and
DLCI?
A. display fr interface
B. display fr
C. display fr map-info
D. display fr brief
Correct Answer: C
Section: (none)
Explanation
QUESTION 116
Which of following may be the reasons that cause Frame Relay PVC to work abnormally? (Choose three)
A. Same DLCI number is configured on the same router

B. LMI type mismatch
C. Frame Relay encapsulation type mismatch
D. Incorrect configuration of the DLCI number
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 117
An administrator wishes to update the VRP software of company’s AR2200 router. How can this be achieved?
Jul 24, 2019

(Choose three)
A. The administrator can use FTP to transfer the VRP software, with the AR2200 router as the FTP client.
B. The administrator can use FTP to transfer the VRP software, with the AR2200 router as the FTP server.
C. The administrator can use TFTP to transfer the VRP software, with the AR2200 router as the TFTP server.
D. The administrator can use TFTP to transfer the VRP software, with the AR2200 router as the TFTP client.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 118
An administrator wishes to implement new features in the network, but the VRP version of one AR2200 router
is out of date. The administrator needs to upgrade the VRP software.
Which of the following options regarding file transfer is false?
A. The AR2200 router can function as a TFTP client to support the upgrade.
B. The AR2200 router can function as the TFTP server to support the upgrade.
C. The AR2200 router can function as the FTP server to support the upgrade.
D. The AR2200 router can function as an FTP client to support the upgrade.
Correct Answer: B
Section: (none)
Explanation
QUESTION 119
FTP and TFTP can be used to update the system file on Huawei routers. Which of the following statements are
correct? (Choose three)
A. Huawei router can be configured as FTP Client

B. Huawei router can be configured as FTP Server
C. Huawei router can be configured as TFTP Client
D. Huawei router can be configured as TFTP Server
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 120
An administrator discovered he/she was unable to use TFTP to transfer files to the router.
Which of the following describes the likely reason for this?
A. The TFTP service had been disabled on the router.

B. TCP port 69 of the server had been blocked.
Jul 24, 2019

C. UDP port 69 of the server had been blocked.
D. The username and password had been modified.
Correct Answer: C
Section: (none)
Explanation
QUESTION 121
FTP may be used to upgrade a router's VRP image.
Which of the following transmission modes should be used to achieve this?
A. binary mode
B. ASCII mode
C. byte mode
D. letter mode
Correct Answer: A
Section: (none)
Explanation
QUESTION 122
A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The client
assumed that the problem was with the port configuration.
The blocking of which ports would likely cause this problem? (Choose two)
A. 21
B. 80
C. 20
D. 50649
Correct Answer: AC
Section: (none)
Explanation
QUESTION 123
When using VRP, which of the following commands is used to configure the data link layer encapsulation type
of a serial interface as HDLC?
A. encapsulation hdlc
B. link-protocol hdlc
C. hdlc enable
D. link-protocol ppp
Correct Answer: B
Jul 24, 2019

Section: (none)
Explanation
QUESTION 124
If AH and ESP are both required to protect data streams between IPsec peers, how many Security Associations
(SA) are required in total?
A. 1
B. 2
C. 3
D. 4
Correct Answer: D
Section: (none)
Explanation
QUESTION 125
Two routers establish an IPsec tunnel, which of the following does not need to be the same on both peering
devices?
A. Encapsulation mode
B. Transform mode
C. Proposal name
D. authentication algorithm
Correct Answer: C
Section: (none)
Explanation
QUESTION 126
Which of the following formats represent an accurate condensing of the IPv6 address
2031:0000:720C:0000:0000:09E0:839A:130B? (Choose two).
A. 2031:0:720C:0:0:9E0:839A:130B
B. 2031:0:720C:0:0:9E:839A:130B
C. 2031::720C::9E0:839A:130B
D. 2031:0:720C::9E0:839A:130B
Correct Answer: AD
Section: (none)
Explanation
QUESTION 127
Which of the following IPv6 addresses can be configured on a router’s interface? (Choose two).
Jul 24, 2019

A. fe80:13dc::1/64
B. ff00:8a3c::9b/64
C. ::1/128
D. 2001:12e3:1b02::21/64
Correct Answer: AD
Section: (none)
Explanation
QUESTION 128
The IPv6 address architecture does not include which of the following address types?
A. unicast
B. multicast
C. broadcast
D. anycast
Correct Answer: C
Section: (none)
Explanation
QUESTION 129
Which of the following descriptions regarding IPv6 addresses are correct? (Choose two)
A. IPv6 addresses are 64 bits in length.

B. IPv6 addresses are 128 bits in length.
C. IPv6 extension headers are processed in order.
D. IPv6 extension headers are processed randomly.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 130
Interface G0/0/1 on RTA contains a MAC address of 00e0-fc03-aa73 and is configured with the IPv6 address
2001::2E0:FCFF:FE03:AA73. Which method is most likely to have been used to configure the interface IPv6
address?
A. DHCPv6
B. Auto-link
C. ARP
D. EUI-64
Correct Answer: D
Section: (none)
Jul 24, 2019

Explanation
QUESTION 131
In a small network supporting IPv6, a network administrator wishes implement RIPng.
Which of the following commands should be used to enable this protocol?
A. [RTA-GigabitEthernet0/0/0]ripng 1 enable
B. [RTA]ripng 1 enable
C. <RTA>ripng 1 enable
D. [RTA-ripng-1]ripng 1 enable
Correct Answer: A
Section: (none)
Explanation
QUESTION 132
In a network supporting IPv6, OSPF no longer supports which feature?
A. multiple areas
B. Router-ID
C. authentication
D. multicast updates
Correct Answer: C
Section: (none)
Explanation
QUESTION 133
The network administrator has decided to configure link aggregation in the enterprise network.
Which of the following represent advantages of link aggregation? (Choose three)
A. Load balancing.
B. Improved bandwidth.
C. Enhanced reliability.
D. Improved security.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 134
In port aggregation, “multiple” ports are aggregated to form a port aggregation group so that all the member
Jul 24, 2019

ports in the group share the outgoing/incoming load.
At which layer is port aggregation implemented?
A. Physical Layer
B. Data Link Layer
C. Network Layer
D. Transport Layer
Correct Answer: B
Section: (none)
Explanation
QUESTION 135
What benefits does port aggregation yield? (Choose three)
A. Improves link bandwidth

B. Implements load sharing
C. Improves network reliability
D. Facilitates data copy for analysis
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 136
What is the maximum number of member interfaces supported by a single Eth-Trunk?
A. 6
B. 8
C. 10
D. 12
Correct Answer: B
Section: (none)
Explanation
QUESTION 137
The Eth-Trunk frame forwarding mechanism used to prevent changes in the data sequence forwards frames
based on which of the following parameters?
A. The same source or destination IP address.

B. The same source or destination MAC address.
C. The same protocol type.
D. The same source or destination port number.
Jul 24, 2019

Correct Answer: AB
Section: (none)
Explanation
QUESTION 138
In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by which of the following?
(Choose all that apply.)
A. Maximum number of Up member links

B. Minimum number of Up member links
C. Number of Up member interfaces
D. Number of interfaces.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 139
The network administrator wishes to forward data over an Eth-trunk, however associated member interfaces
operate at different rates. In terms of the resulting behavior, which of the following is true?
A. The two switches will not be able to communicate.

B. The higher rate member interfaces may incur packet loss.
C. The Eth-Trunk will work normally.
D. The lower rate member interfaces may incur packet loss.
Correct Answer: D
Section: (none)
Explanation
QUESTION 140
The network administrator attempts to add interface G0/0/1 on Switch A to Eth-trunk 1, however the command
fails.
Which of the following may cause this?
A. The interface is operating in half-duplex mode.

B. The interface has been shutdown.
C. The interface is already associated with another Eth-trunk.
D. The interface is an access port.
Correct Answer: CD
Section: (none)
Explanation
Jul 24, 2019

QUESTION 141
A network requires a solution to allow 50 private IP addresses to be translated, however only a single public
address is available for use.
Which translation method can be used to support this requirement?
A. Static NAT
B. Dynamic NAT
C. Easy-IP
D. NAPT
Correct Answer: C
Section: (none)
Explanation
QUESTION 142
NAPT allows for multiple internal addresses to be mapped to a single public address.
How does NAT distinguish between the different private addresses when mapping to the same public address?
A. The source MAC address is used.

B. The destination MAC address is used.
C. The source port number is used.
D. The destination port number is used.
Correct Answer: C
Section: (none)
Explanation
QUESTION 143
A web server in a private network is required to provide HTTP services to public users. The network
administrator is required to configure NAT on RTA.
Which configuration should be used?
A. [RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
B. [RTA-Serial0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
Jul 24, 2019

C. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
D. [RTA- Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
Correct Answer: A
Section: (none)
Explanation
QUESTION 144
The network administrator needs to configure static NAT on RTA, in order to allow Host A to communicate with
Host C.
Which command is correct?
A. [RTA-Serial1/0/1]nat outbound 200.1.1.10

B. [RTA-Serial1/0/1]nat static global 200.1.1.10 inside 192.168.1.0
C. [RTA-Serial1/0/1]nat static global 192.168.1.1 inside 200.1.1.10
D. [RTA-Serial1/0/1]nat static global 200.1.1.10 inside 192.168.1.1
Correct Answer: D
Section: (none)
Explanation
QUESTION 145
[RTA-GigabitEthernet0/0/0]nat outbound 2000 address-group 1
Refer to the configuration output. What does the value “2000” refer to?
A. It represents the ACL number.

B. It represents the NAT number.
C. It represents the translated port number.
D. It represents the number of bytes that can be translated before the address is returned to the public address
pool.
Jul 24, 2019

Correct Answer: A
Section: (none)
Explanation
QUESTION 146
NAPT uses the same public address but different port numbers to translate private addresses.
Which statement regarding the port number is correct?
A. It is necessary to configure port number mapping manually.

B. It is only necessary to configure the port number range.
C. It is not necessary to configure port numbers.
D. An access control list is needed to assign port numbers.
Correct Answer: C
Section: (none)
Explanation
QUESTION 147
A configured internal host of a private network wishes to access the internet. What must be configured on the
enterprise network egress router in order to achieve this? (Choose all that apply.)
A. NAT Easy IP
B. DHCP
C. BGP
D. Default route
Correct Answer: AD
Section: (none)
Explanation
QUESTION 148
Which of the following statements are correct about NAT? (Choose three)
A. NAT is the abbreviation for "Network Address Translation".

B. NAT is used for translation between private and public network addresss.
C. When hosts inside a private network access the outside network, NAT is not required.
D. NAT provides an effective way to solve the problem of insufficient IP addresses.
Correct Answer: ABD

Section: (none)
Explanation
Jul 24, 2019

QUESTION 149
Which of the following technologies can allow a host with IP address 10.0.0.1 to access the internet?
A. Static route
B. Dynamic route
C. Route import
D. NAT
Correct Answer: D
Section: (none)
Explanation
QUESTION 150
Which of the following items can be translated by NAPT?
A. MAC address + port number

B. IP address + port number
C. Only MAC address
D. Only IP address
Correct Answer: B
Section: (none)
Explanation
QUESTION 151
Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose
three)
A. The port receives only RIPv2 multicast packets.

B. The port does not receive RIPv1 broadcast packets.
C. The port does not receive RIPv2 broadcast packets.
D. The port receives only RIPv1 multicast packets.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 152
Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)
A. The router IDs of OSPF routers in the same area must be the same, but can be different in different areas.
B. The router ID must be the IP address of an OSPF router interface.
C. The router ID must be configured manually.
D. A router running OSPF must have a router ID for it to operate properly.
Correct Answer: ABC
Jul 24, 2019

Section: (none)
Explanation
QUESTION 153
Which of the following statements regarding Designated Routers in OSPF are correct? (Choose three)
A. DR is elected by all the routers in the same network segment.

B. If the priorities of two routers are different, the router with the lower priority will be elected as DR.
C. If the priorities of two routers are equal, the router with the higher Router ID will be elected as DR.
D. DR and BDR must be adjacent.
Correct Answer: ACD

Section: (none)
Explanation
QUESTION 154
On the VRP platform, which of the following commands is used to configure the Router ID of a router as
1.1.1.1?
A. <Huawei>router id 1.1.1.1
B. [Huawei]router id 1.1.1.1
C. [Huawei]router-id 1.1.1.1
D. [Huawei]router id 1.1.1.1 255.255.255.255
Correct Answer: B
Section: (none)
Explanation
QUESTION 155
Which of the following OSPF versions is specific to IPv6?
A. OSPFv1
B. OSPFv2
C. OSPFv3
D. OSPFv4
Correct Answer: C
Section: (none)
Explanation
QUESTION 156
The administrator wishes to configure OSPF on a router in the network however the router has no loopback
interface.
Jul 24, 2019

Which value will be used as the router ID?
A. The lowest IP address of the router’s active interfaces.

B. The highest IP address of the router’s active interfaces.
C. The IP address of the management interface.
D. The priority value of the router.
Correct Answer: B
Section: (none)
Explanation
QUESTION 157
An administrator of a company supporting a large enterprise network wishes to implement OSPF on the
network as opposed to RIP. Which of the following points should the administrator use to support his reasoning
for this change? (Choose three)
A. OSPF has no hop count limitation.

B. OSPF has a lower routing update overhead.
C. OSPF has a simpler configuration.
D. OSPF supports faster convergence.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 158
Which of the following statements regarding single area OSPF are correct? (Choose three)
A. An IP address needs to be configured on a loopback interface of each router before configuring an OSPF
area.
B. The value of an area can be from 0.0.0.0 to 255.255.255.255.
C. A single area can be configured using any supported area number.
D. All of the links of the network need to be advertised in Area 0.
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 159
10.0.1.0/24 O_ASE 150 2 D 10.0.23.3 Serial2/0/0
Refer to the display output. Which of the following statements regarding route shown are true? (Choose two)
A. The address 10.0.23.3 has been configured on the peer’s serial 2/0/0 interface.
B. The route preference has been changed by the administrator.
C. The metric for the route 10.0.1.0 indicates that two hops are needed.
Jul 24, 2019

D. The route has been learned via the OSPF protocol.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 160
Which of the following statements regarding link-state database and routing-table of a “single” OSPF area are
correct? (Choose two)
A. The link-state databases that all routers build are identical.

B. The link-state databases that all routers build are different.
C. The routing-tables that all routers calculate are different.
D. The routing-tables that all routers calculate are identical.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 161
Which of the following steps are necessary to configure OSPF on a Huawei router? (Choose three)
A. Configuration of a router ID
B. Enabling of an OSPF process
C. Specifying an OSPF area
D. Configuration of the network segments within each area
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 162
Which of the following statements regarding the DR in an OSPF network are correct? (Choose two)
A. There must be at least one DR in an OSPF area.

B. A DR must be elected among the routers through the negotiations that are defined by OSPF protocol.
C. Only the router with highest priority will be elected as DR.
D. Only NBMA or Broadcast networks need to elect DR.
Correct Answer: BD
Section: (none)
Explanation
QUESTION 163
Jul 24, 2019

Which of the following VRP commands can be used to enter area 0 view? (Choose two)
A. [Huawei]ospf area 0
B. [Huawei-ospf-1]area 0
C. [Huawei-ospf-1]area 0.0.0.0
D. [Huawei-ospf-1]area 0 enable
Correct Answer: BC
Section: (none)
Explanation
QUESTION 164
Which of the following commands is used to display the OSPF neighbor relationship establishment?
A. display ospf neighbor

B. display ospf brief
C. display ospf peer
D. display ospf interface
Correct Answer: C
Section: (none)
Explanation
QUESTION 165
With what kind of routers does a DRother router exchange link state information and route information?
(Choose two)
A. DR
B. BDR
C. DRother
D. All OSPF neighbors
Correct Answer: AB
Section: (none)
Explanation
QUESTION 166
An OSPF area is a collection of a group of routers and networks. OSPF defines that routers that have the same
( ) belong to the same OSPF area.
A. neighbors
B. LSDB
C. LSA
D. adjacency
Correct Answer: B
Jul 24, 2019

Section: (none)
Explanation
QUESTION 167
Which of the following statements about router IDs are true? (Choose two)
A. The routers contained in the same LSDB have the same router ID.
B. Each router in an OSPF network must have a unique router ID.
C. Two routers in different OSPF areas can have the same router ID.
D. A router ID is expressed in a 32-bit dotted decimal format.
Correct Answer: BD
Section: (none)
Explanation
QUESTION 168
OSPF allows for “multiple” processes. By default, OSPF selects a process whose number is ( ).
A. 0
B. 1
C. 10
D. 100
Correct Answer: B
Section: (none)
Explanation
QUESTION 169
In a network supporting IPv6, OSPF no longer supports which feature?
A. multiple areas
B. Router-ID
C. authentication
D. multicast updates
Correct Answer: C
Section: (none)
Explanation
QUESTION 170
Two routers are configured with OSPFv3. OSPFv3 is enabled on all interfaces of each router.
Which of the following is true in the event that the network administrator does not configure a Router-ID?
Jul 24, 2019

A. The IP address of the loopback 0 interface will be used as the router ID.
B. The IP address of the loopback 1 interface will be used as the router ID.
C. The IP address of interface G0/0/0 will be used as the router ID.
D. No router ID will be assigned to the router.
Correct Answer: D
Section: (none)
Explanation
QUESTION 171
Refer to the graphic. Which of the following statements is correct when this router forwards the packet to the
destination host 9.1.4.5?
A. The router selects the first entry to match the destination address of the packet because the preference of
OSPF is higher than the preference of RIP.
B. The router selects the second entry to match the destination address of the packet because the cost of RIP
is lower than that of OSPF.
C. The router selects the second entry to match the destination address of the packet because the outgoing
interface is an Ethernet interface. The forwarding speed of an Ethernet interface is faster than the
forwarding speed of a serial interface
D. The router selects the second entry to match the destination address of the packet because the router will
match the most specific address.
Correct Answer: D
Section: (none)
Explanation
QUESTION 172
According to the default value of route preference on the VRP platform, which of the following represent the
correct sequence for direct route, static route, RIP and OSPF if they are listed from high preference to low
preference?
A. Direct, Static, RIP, OSPF

B. Direct, OSPF, Static, RIP
C. Direct, OSPF, RIP, Static
D. Direct, RIP, Static, OSPF
Correct Answer: B
Section: (none)
Explanation
Jul 24, 2019

QUESTION 173
A router has learned two routes for the same network with the same prefix. One route has been learned via
OSPF with a metric of 4882, while the other route has been learned via RIPv2 with a metric of 4.
Which route (s) will be found in the routing table?
A. The RIPv2 route.

B. The OSPF and RIPv2 routes.
C. The OSPF route.
D. Neither of these routes will be found in the routing table.
Correct Answer: C
Section: (none)
Explanation
QUESTION 174
Assume that the router has learnt the best route to the same destination by using RIP, OSPF and Static Route
respectively. By default, the Huawei router will select the route learnt via ( ) as the best route.
A. RIP
B. OSPF
C. RIPv2
D. Static route
Correct Answer: B
Section: (none)
Explanation
QUESTION 175
After checking the OSPF neighbor state, the administrator discovers that the router has established a
TWOWAY state with the peering router.
What can be understood from this information? (Choose two)
A. The routers are configured using the same process ID

B. The routers are configured using the same area ID
C. The routers are configured using wrong router ID
D. The routers are considered DROthers in a broadcast network
Correct Answer: D
Section: (none)
Explanation
QUESTION 176
What functions does a Hello packet of OSPF implement? (Choose two)
Jul 24, 2019

A. Neighbor discovery
B. Deletion of unreachable neighbors
C. Maintaining of neighbor relationships
D. Negotiation of parameters among adjacent ports
Correct Answer: AC
Section: (none)
Explanation
QUESTION 177
Two routers are connected through serial interfaces and support PPP encapsulation.
Which parameters must be negotiated to establish the PPP connection? (Choose three).
A. MRU
B. Authentication password
C. Magic-Number
D. IP address
Correct Answer: ACD

Section: (none)
Explanation
QUESTION 178
What are the three protocol components defined by PPP? (Choose three).
A. Data encapsulation.
B. LCP
C. NCP
D. IPCP
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 179
Two routers are connected via serial interfaces, for which the link-protocol is PPP. The network administrator
wishes to configure PPP authentication to improve security on this link.
Which PPP authentication method provides a more secure solution?
A. CHAP
B. PAP
C. MD5
D. SSH
Jul 24, 2019

Correct Answer: A
Section: (none)
Explanation
QUESTION 180
If PPP authentication fails, which type of packet will be sent to the authenticated peer by the authenticator?
A. Authenticate-Ack
B. Authenticate-Nak
C. Authenticate-Reject
D. Authenticate-Reply
Correct Answer: B
Section: (none)
Explanation
QUESTION 181
Two routers are connected via serial interfaces and the link-protocol is PPP, but the MRU of two serial
interfaces are different, in PPP LCP negotiated stage, what will happen?
A. LCP negotiation will fail

B. Negotiation will use the smaller value
C. Negotiation will use the larger value
D. Negotiation will use 1500
Correct Answer: B
Section: (none)
Explanation
QUESTION 182
PPP is more secure than HDLC because PPP supports authentication protocols such as ( ). (Choose two)
A. PAP
B. MD5
C. CHAP
D. SSH
Correct Answer: AC
Section: (none)
Explanation
QUESTION 183
When both ends running PPP protocol detect that the physical link is active, the link state will transit from dead
to establish.
Jul 24, 2019

Which of the following protocols is used to negotiate the link parameters during this phase?
A. IP
B. DHCP
C. LCP
D. NCP
Correct Answer: C
Section: (none)
Explanation
QUESTION 184
A serial interface of a Huawei router currently using HDLC needs to assign PPP as the encapsulation protocol.
Which of the following commands is required to be configured at the serial interface view?
A. link-protocol ppp
B. encapsulation ppp
C. enable ppp
D. address ppp
Correct Answer: A
Section: (none)
Explanation
QUESTION 185
When using VRP, which of the following commands is used to configure the PPP authentication method as
PAP?
A. ppp pap
B. ppp authentication-pap
C. ppp authentication-mode pap
D. ppp pap-authentication
Correct Answer: C
Section: (none)
Explanation
QUESTION 186
When configuring the PPP authentication method as PAP, which of the following operations are necessary?
(Choose three)
A. Add the user name and password of the authenticated party to the local user list.
B. Configure the encapsulation type of the interface connected to the peer as PPP.
C. Configure PPP authentication method as CHAP.
Jul 24, 2019

D. On the authenticated party end, configure the user name and password that are sent to authenticator.
Correct Answer: ABD

Section: (none)
Explanation
QUESTION 187
In the PPP protocol, which of the following encryption algorithms is used by CHAP?
A. DES
B. MD5
C. AES
D. None
Correct Answer: B
Section: (none)
Explanation
QUESTION 188
What is the function of the “ip address ppp-negotiate” command?
A. Enables the function of requesting for an IP address from the peer device.
B. Enables the function of accepting the request for an IP address from the remote device.
C. Enables the function of statically allocating IP addresses to the peer.
D. None of the above.
Correct Answer: A
Section: (none)
Explanation
QUESTION 189
Two routers have established a point-to-point network using PPP. The administrator has configured the routers
to run OSPF in the same area with the same router ID, what will behavior will occur as a result of the
configuration?
A. The routers will build a neighbor relationship even though both routers are using the same router ID.
B. VRP will notify of a router ID conflict between the two routers.
C. The routers will build an adjacency even though both routers are using the same router ID.
D. The routers will not send hello packets to each other because they are using the same router ID.
Correct Answer: B
Section: (none)
Explanation
Jul 24, 2019

QUESTION 190
The PPPoE session establishment process can be divided into which stages? (Choose all that apply.)
A. Discovery stage
B. DHCP stage
C. PPPoE Session stage
D. PPP connecting stage.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 191
To establish multiple PPP point-to-point connections in the Ethernet network, a PPPoE server establishes
connections with multiple PPPoE clients on one Ethernet port.
How does PPPoE differentiate between each connection?
A. MAC address.
B. IP address and MAC address
C. MAC address and ppp-id
D. MAC address and session-id
Correct Answer: D
Section: (none)
Explanation
QUESTION 192
When configuring a router as a PPPoE client, which configuration is not necessary?
A. Configuration of the dialer-rule

B. Configuration of the dialer interface
C. Configuration of an IP address on the dialer interface
D. Configuration of a password on the dialer interface
Correct Answer: C
Section: (none)
Explanation
QUESTION 193
In the PPPoE discovery stage, the PPPoE server assigns a session-id to the PPPoE client in which packet?
A. PADI
B. PADO
C. PADR
D. PADS
Jul 24, 2019

Correct Answer: D
Section: (none)
Explanation
QUESTION 194
Which command can be used to check the PPPoE client session status?
A. display ip interface brief

B. display current-configuration
C. display pppoe-client session packet
D. display pppoe-client session summary
Correct Answer: D
Section: (none)
Explanation
QUESTION 195
[Huawei]rip 1
[Huawei-rip-1]version 2
Refer to the command output. An administrator wishes to configure RIP. Which other command needs to
configured for RIP routes to be advertised?
A. import-route GigabitEthernet 0/0/1

B. network 192.168.1.0 0.0.0.255
C. network GigabitEthernet 0/0/1
D. network 192.168.1.0
Correct Answer: D
Section: (none)
Explanation
QUESTION 196
A RIP router receives the routing update information from its neighbor.
Which of the following statements regarding routing update are correct? (Choose three)
A. The received route that is not in the routing table will be added only when its hop count value is less than 16.
B. The received route that already exists in the routing table will be updated only when the next hop is the
router's neighbor and the cost value is smaller.
C. The received route that already exists in the routing table will be updated only when the next hop is not the
router's neighbor and the cost value is smaller.
D. The received route that already exists in the routing table will be updated only when the next hop is the
router's neighbor and the cost value has been changed.
Correct Answer: ACD
Jul 24, 2019

Section: (none)
Explanation
QUESTION 197
Which of the following commands is used to display the current running state and configuration of RIP?
A. display protocol rip

B. show rip
C. display rip
D. display this rip
Correct Answer: C
Section: (none)
Explanation
QUESTION 198
A user can view the information for the RIP protocol on a router. What does “Age time” in the returned result of
the command mean?
A. The interval of updating an RIP packet

B. The aging time of an RIP route
C. The suppression time of an RIP route
D. The time spent on switching between RIP routes
Correct Answer: B
Section: (none)
Explanation
QUESTION 199
After a command for displaying RIP route information is entered on a router, peer 192.168.1.2 on Serial1/0/0 is
displayed in the returned result.
What does 192.168.1.2 stand for?
A. Address of a RIP neighbor

B. Address of the port with the RIP protocol enabled
C. Next hop address of the RIP route
D. Transmission address of the RIP protocol
Correct Answer: A
Section: (none)
Explanation
QUESTION 200
Jul 24, 2019

Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not as
expected and performs debugging. Based on the output from the debug, what is the source of the problem?
A. R2 has configured an ACL to block the route to network 1.0.0.0

B. R2 has enabled split horizon.
C. R1 is using authentication, however R2 is not.
D. R2 is operating using RIPv2, while R1 is using RIPv1.
Correct Answer: D
Section: (none)
Explanation
QUESTION 201
Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose
three)
A. The port receives only RIPv2 multicast packets.

B. The port does not receive RIPv1 broadcast packets.
C. The port does not receive RIPv2 broadcast packets.
D. The port receives only RIPv1 multicast packets.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 202
When a network administrator configures STP in the network, BPDU begin to be sent by switch. Which of the
following statements regarding the BPDU frame are correct?
A. A BPDU uses the IEEE 802.3 standard frame type

B. A BPDU uses the Ethernet II standard frame type
C. The BPDU frame’s control field is 3
D. The destination MAC address field of a BPDU frame is a broadcast address
Correct Answer: A
Jul 24, 2019

Section: (none)
Explanation
QUESTION 203
In the case of Huawei router, the Tracert command uses UDP to encapsulate probe packets.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 204
The broadcast address of the subnet 192.168.1.0/25 is 192.168.1.128.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 205
A network administrator wishes to assign an IP address to a router interface G0/0/0. Which of the following IP
addresses can be assigned?
A. 192.168.10.112/30
B. 237.6.1.2/24
C. 145.4.2.55/26
D. 127.3.1.4/28
Correct Answer: C
Section: (none)
Explanation
QUESTION 206
If a network’s address is 192.168.1.0, the broadcast address of the network is 192.168.1.255.
A. True
B. False
Correct Answer: A
Section: (none)
Jul 24, 2019

Explanation
QUESTION 207
In the VRP system, what are the functions of Ctrl+Z?
A. Return from the system view to the user view

B. Exit from the current view
C. Exit from the interface view
D. Exit from the console interface view
E. Return to the user view
Correct Answer: A
Section: (none)
Explanation
QUESTION 208
In standard STP mode, which of the following ports on non-root switches forward the BPDUs with TC bits set
generated by the root switch?
A. Root port
B. Backup port
C. Designated port
D. Alternate port
Correct Answer: A
Section: (none)
Explanation
QUESTION 209
Assuming all STP enabled switches have the same bridge priority. The MAC address of switch A is 00-e0-fc-
00-00-40, the MAC address of switch B is 00-e0-fc-00-00-10, the MAC address of switch C is 00-e0-fc-00-00-
20, and the MAC address of switch D is 00-e0-fc-00-00-80.
Which switch will be elected as the root switch?
A. Switch A
B. Switch B
C. Switch C
D. Switch D
Correct Answer: B
Section: (none)
Explanation
QUESTION 210
Jul 24, 2019

As specified by the RSTP protocol, when a root port fails, which type of port will function as a new root port and
enters the forwarding state without any delay?
A. Forwarding Port
B. Alternate Port
C. Backup Port
D. Edge Port
Correct Answer: B
Section: (none)
Explanation
QUESTION 211
In STP, the priority of the STP root switch ranges from 0 to 65536.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 212
Refer to the graphic. Which statements correctly explains the forwarding behavior between RTA and RTE?
(Choose all that apply)
Jul 24, 2019

A. When the network uses OSPF, data will be forwarded along the path via S1/0/0
B. When the network uses RIPv2, data will be forwarded along the path via S1/0/0
C. When the network uses OSPF, data will be forwarded along the path from via E0/0/1
D. When the network uses RIPv2, data will be forwarded along the path via S2/0/0
Correct Answer: BC
Section: (none)
Explanation
QUESTION 213
Refer to the graphic. RTA and RTB are running RIPv1. RTA has advertised 10.0.0.0 and 192.168.1.0 to the RIP
network. Which routes will exist in the IP routing table of RTB? (Choose all that apply)
A. 10.0.0.0/8
B. 192.168.1.1/32
C. 10.1.12.1/32
D. 192.168.1.0/24
Correct Answer: AD
Section: (none)
Explanation
QUESTION 214
Which of the following configurations regarding static route are correct? (Choose all that apply)
A. ip route-static 129.1.0.0 16 serial 0

B. ip route-static 10.0.0.2 16 129.1.0.0
C. ip route-static 129.1.0.0 16 10.0.0.2
D. ip route-static 129.1.0.0.255.255.0.0 10.0.0.2
Correct Answer: ACD

Section: (none)
Explanation
Jul 24, 2019

QUESTION 215
Refer to the graphic. An administrator has configured RIPv2 in the two routers. What will happen after
configuring the following commands: (Choose all that apply)
A. RTA will have the route learned from the RTB

B. RTB will have the route learned from the RTA
C. RTA will have no neighbor relationship with RTB
D. RTB will have no neighbor relationship with RTA
Correct Answer: AD
Section: (none)
Explanation
QUESTION 216
Refer to the graphic. OSPF is used on four routers that are in the same area and on the same network
segment. In this scenario, OSPF selects one DR and multiple BDRs to ensure backup.
Jul 24, 2019

A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 217
On Huawei devices, you can use the undo summary command to prohibit automatic route summarization of
RIPv2.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 218
Which of the following configurations regarding default route configuration is correct?
A. [Quidway] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1

B. [Quidway] ip route-static 0.0.0.0 255.255.255.255 172.16.2.1
C. [Quidway-GigabitEthernet0/0/1] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1
D. [Quidway] ip route static 0.0.0.0 0.0.0.0 172.16.2.1
Correct Answer: A
Section: (none)
Explanation
QUESTION 219
Which of the following WLAN standards support operation in the 5GHz range? (Choose all that apply)
A. 802.11a
B. 802.11b
C. 802.11g
D. 802.11n
Correct Answer: AD
Section: (none)
Explanation
QUESTION 220
On Huawei switches, you can run the vlan batch command to create multiple VLANs in batches.
Jul 24, 2019

A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 221
According to the topology and configuration of interconnected interfaces of switches shown in the figure, the
data frame tagged with VLAN 10 can be forwarded correctly between the two switches.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 222
The network administrator creates VLAN 10 and assigns an IP address to VLANIF10. When using the
command “display ip interface brief”, the administrator finds that VLANIF10 is down. What should be done to
enable VLANIF10?
A. Use the command “undo shutdown” under the interface view for VLANIF10
B. Assign a physical interface that has either an active of inactive physical state to VLAN 10
C. Assign only a physical interface that has an active physical state to VLAN 10
D. Add an interface that has an active physical state and a trunk port associated with VLAN 10
Correct Answer: C
Section: (none)
Explanation
QUESTION 223
A network administrator wishes to implement VLAN 10 to isolate certain users. It is common however for these
users to often change their physical location. Which of the following VLAN implementations should be used?
A. Port based VLAN assignment

B. Protocol based VLAN assignment
C. MAC based VLAN assignment
D. IP subnet based VLAN assignment
Correct Answer: C
Section: (none)
Explanation
QUESTION 224
Refer to the graphic. GE0/0/1 and GE0/0/2 on the switch are configured as hybrid interfaces. Which of the
following statements are true? (Choose all that apply)
Jul 24, 2019

A. The administrative department and the finance department cannot communicate with each other because
the VLANs of the two departments are different.
B. The data frames sent by the administrative department carry tagged VLAN 20 on the switch.
C. On the switch, the data frames sent by the finance department carry tagged VLAN 20.
D. The switch can be a Layer 2 or Layer 3 switch because communications do not need to be transmitted
through a Layer 3 gateway.
E. If GE0/0/1 and GE0/0/2 on the switch are changed to trunk ports, the administrative department and finance
department can communicate with each other.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 225
Jul 24, 2019

On the VRP, what is the function of the “interface vlanif <vlan-id>” command?
A. It is used to create a VLANIF interface

B. It is used to create a VLANIF interface and enter the VLANIF interface view
C. It is used to configure a VLAN for a VLANIF interface
D. There is no such command
Correct Answer: B
Section: (none)
Explanation
QUESTION 226
InARP resolves the protocol address of the remote device on each virtual circuit, including IP addresses and
IPX addresses.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 227
On an FR network, the DLCI identifies a virtual circuit on an interface. The DLCI must be unique during
planning and deployment.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 228
If AAA authentication is used on Huawei devices and the remote server does not respond, the authentication
can be performed on network devices.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 229
An ACL does not filter traffic generated by the Huawei device towards other devices, but only filters forwarded
traffic, including traffic generated by other devices to access the Huawei device.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 230
Which of the following statements are true about ACL deployment on Huawei devices? (Choose all that apply)
A. ACL can only be used in the outbound direction of an interface

B. The same ACL can be used on multiple interfaces
C. The ACL rules can only be configured in the following sequence: 10, 20, 30…
D. ACLs cannot be used to filter OSPF traffic because OSPF does not use UDP to encapsulate packets
E. ACLs can be used to match with the TCP/UDP port IDs of packets and to designate the port ID range
Correct Answer: BE
Section: (none)
Explanation
QUESTION 231
SNMP packets are encapsulated in TCP packets.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 232
In OSPFv3, router IDs can be used automatically generated by the system.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 233
VLSM can expand any IP network segment, including Class D addresses.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 234
Refer to the graphic, 00e0-fc99-9999 is a specific host MAC address learned by a switch through ARP and the
host changes the IP address three times.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
QUESTION 235
There are two routers (RTA and RTB) between the source device and destination device. The Tracert
command is used to detect the path between the two devices. During detection of the first hop (RTA), the
source device sends a UDP packet with a TTL of 1 to an interface with a large interface number on the
destination device. The TTL turns to 0 when the packet arrives at RTB, upon which RTA sends an ICMP
______ message to the source device.
A. Time Exceeded.
B. Echo Request.
C. Echo Reply.
D. Port Unreachable.
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 236
Which of the following statements are true about ICMP messages? (Multiple Choice)
A. ICMP messages can record time, including the original time, packet receiving time, and packet sending
time.
B. ICMP messages are encapsulated in IP packets but not at the transport layer.
C. ICMP messages include error messages, control messages, request/response messages, and update
messages.
D. ICMP does not support redirection.
E. ICMP messages cannot be used to detect a path’s MTU.
Correct Answer: BC
Section: (none)
Explanation
QUESTION 237
If a network’s broadcast address is 172.16.1.255, which of the following addresses can be the network
address?
A. 172.16.2.0
B. 172.16.1.253
C. 172.16.1.128
D. 172.16.1.1
Correct Answer: C
Section: (none)
Explanation
QUESTION 238
On the command line interface of Huawei AR routers, the role of the Save command is to Save the current
system time.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 239
Which of the following technologies is used to bind MAC addresses to interfaces on a switch?
A. SEP.
B. Port security.
Jul 24, 2019

C. ACL.
D. NAT.
Correct Answer: B
Section: (none)
Explanation
QUESTION 240
In RSTP, a backup port can replace a faulty root port.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
QUESTION 241
During STP calculation, the port cost is associated with port bandwidth. Which of the following statements
about the relation between port cost and port bandwidth is true?
A. Port cost decreases when port bandwidth increases.

B. Port cost increases when port bandwidth increases.
C. Port cost is consistent with port bandwidth.
D. Port cost varies randomly according to port bandwidth.
Correct Answer: A
Section: (none)
Explanation
QUESTION 242
Which of the following descriptions about STP are incorrect? (Multiple Choice)
A. A layer-2 switching network can have only one designated switch.

B. All the ports of the root switch are root ports.
C. All the ports of the root switch are designated ports.
D. The switch with the smallest priority value is elected as non-root switch.
Correct Answer: BD
Section: (none)
Explanation
QUESTION 243
Which of the following statements about static route preference on Huawei devices is false?
Jul 24, 2019

A. Static route preference ranges from 0 to 255.
B. Default static route preference is 60.
C. Static route preference is either internal or external. Administrators can modify external preferences.
D. If static route preference is 255, the route cannot be used.
Correct Answer: A
Section: (none)
Explanation
QUESTION 244
Refer to the graphic, which of the following statements is true about OSPF topology and configuration?
A. A stable OSPF neighbor relationship can be set up between R1 and R2.

B. After the default network type of the interface on R1 is restored to broadcast, a stable OSPF neighbor
relationship can be set up between R1 and R2.
C. After the default network type of the interface on R1 is restored to broadcast and the hello packet sending
interval is changed to 10s, a stable OSPF neighbor relationship can be set up between R1 and R2.
D. Compared with R1, R2 is more likely to become the DR because the DR priority of the interface on R2 is
lower than that of R1.
Correct Answer: C
Section: (none)
Explanation
Jul 24, 2019

QUESTION 245
Refer to the graphic. An administrator has configured OSPF on the two routers, following which he then
implements the command silent-interface s0/0/1 on RTA. What effect will this command have on the network?
(Multiple Choice)
A. The link information advertised by RTB will be maintained in the Link State Database of RTA.
B. The OSPF neighbor relationship will fail between two routers.
C. The configuration will not affect the OSPF neighbor relationship between the two routers.
D. The link information advertised by RTB will no longer be maintained in the Link State Database of RTA.
Correct Answer: B
Section: (none)
Explanation
QUESTION 246
In an RIP process on a Huawei device, which of the following configurations are correct for advertising network
10.1.1.1/30? (Multiple Choice)
A. network 10.1.1.0
B. undo summary
network 10.1.1.0
C. version 2
undo summary
network 10.0.0.0
D. undo summary
network 10.1.0.0
E. network 10.0.0.0
Correct Answer: B
Section: (none)
Explanation
QUESTION 247
The following configuration commands implement route backup on RTA for a route to the same destination
10.1.1.0.
A. TRUE
Jul 24, 2019

B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 248
Refer to the command output. Which statement is true regarding this command?
A. The configuration represents a static route to the 192.168.1.1 network

B. The configuration represents a static route to the 10.0.12.0 network.
C. The preference value of this configured route is 100.
D. If the router has learned the same destination network via a dynamic routing protocol, the static route will
always take precedence.
Correct Answer: B
Section: (none)
Explanation
QUESTION 249
Which of the following network types does OSPF support? (Multiple Choice)
A. Point-to-Point.
B. Broadcast.
C. Non-Broadcast Multi-Access.
D. Point-to-Multipoint.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 250
A DHCP Offer packet can carry only one DNS server address.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Jul 24, 2019

QUESTION 251
Refer to the graphic. Host A and Host B use VLAN routing to facilitate communication. What must be
configured on interface G0/0/1.1 of RTA to achieve this?
A. dot1q termination vid 1.

B. dot1q termination vid 10.
C. dot1q termination vid 20.
D. dot1q termination vid 30.
Correct Answer: B
Section: (none)
Explanation
QUESTION 252
Refer to the configuration output. Which following statements are correct? (Multiple choice)
A. VLAN 1 cannot pass over interface Gigabit Ethernet 0/0/1.
Jul 24, 2019

B. VLAN 1 can pass over interface Gigabit Ethernet 0/0/1.
C. Prior to changing the link-type to access, the command “undo port trunk allow-pass vlan all” must be used
to renew the default configurations.
D. Prior to changing the link-type to access, the command “undo port trunk allow-pass vlan 2 to 4096” must be
used to renew the default configurations.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 253
Link aggregation is a common technique in enterprise network. Which of the following description is the
advantages of link aggregation? (Multiple Choice)
A. Improves link bandwidth.

B. Implements load sharing.
C. Improves network reliability.
D. Facilitates data copy for analysis.
Correct Answer: ABC

Section: (none)
Explanation
QUESTION 254
On Huawei switches, VLAN 4095 cannot be created and VLAN 1 cannot be deleted.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
QUESTION 255
Refer to the graphic, after the ping 10.1.1.2 command is executed on R1, LSW1 receives a tagged data frame
from VLAN 10 on LSW2.
Jul 24, 2019

A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
QUESTION 256
Refer to the graphic, which of the following statements are true about VLAN configuration on Huawei switches?
(Multiple Choice)
Jul 24, 2019

A. Client1 belongs to VLAN 10 and the VLAN assignment command on LSW1 is correct.
B. Client2 belongs to VLAN 20, and the MAC address-based VLAN assignment command on LSW1 is correct.
C. Client3 is in VLAN 30, and the VLAN assignment command on LSW1 is correct.
D. Client4 belongs to VLAN 40, and the VLAN assignment command on LSW1 is correct.
E. Client4 does not belong to VLAN 40, and the VLAN assignment command on LSW1 is incorrect.
Correct Answer: ACD

Section: (none)
Explanation
QUESTION 257
Which of the following statements is true about the PPP configuration and deployment?
A. PPP cannot be used to deliver IP addresses.

B. PPP supports both CHAP and PAP authentication.
C. PPP cannot change the keepalive time.
D. PPP does not support bidirectional authentication.
Jul 24, 2019

Correct Answer: B
Section: (none)
Explanation
QUESTION 258
According to the following topology and configuration, R1 and R2 are connected through low-speed serial
cables and PPP is used to encapsulate data link layer packets. When the Holdtime values of R1 and R2 are
different, PPP negotiation and communication fail.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
QUESTION 259
Refer to the graphic. IPsec VPN uses ESP to encrypt which fields?
A. TCP, Data and ESP Trailer.

B. ESP, TCP and Data.
C. ESP, TCP, Data and ESP Trailer.
D. ESP, TCP, Data, ESP Trailer and ESP Auth.
Correct Answer: A
Section: (none)
Explanation
QUESTION 260
Jul 24, 2019

The authentication, authorization and accounting schemes and HWTACACS or RADIUS server templates
created on AR routers take effect only after being applied to a domain.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
QUESTION 261
Which SNMP version focuses on two main aspects, namely security and administration. The security aspect is
addressed by offering both strong authentication and data encryption for privacy. The administration aspect is
focused on two parts, namely notification originators and proxy forwarders.
A. SNMPv1
B. SNMPv2
C. SNMPv2c
D. SNMPv3
Correct Answer: D
Section: (none)
Explanation
QUESTION 262
Which of the following route entries can be aggregated into 10.0.0.24/29? (Choose all that apply.)
A. 10.0.0.25/30
B. 10.0.0.23/30
C. 10.0.0.26/30
D. 10.0.0.22/30
Correct Answer: AC
Section: (none)
Explanation
QUESTION 263
According to the configuration of single-armed routing in the following figure, the administrative department and
finance department can communicate with each other even the proxy ARP is disabled on the subinterface on
R1.
Jul 24, 2019

A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 264
Jul 24, 2019

In the private network, RTA dynamically assigns a public address from the address pool to hosts
without port translation. Host C wishes to access the public network while addresses are assigned to Host A
and Host B. What will occur as a result?
A. The first public address will be allocated to Host C, and Host A will be forced offline.
B. The last public address will be allocated to Host C, and Host B will be forced offline.
C. Host C will be unable to forward traffic over the public network.
D. All hosts will have access to the public network through pool address swapping.
Correct Answer: C
Section: (none)
Explanation
QUESTION 265
After the keepalive function is enabled for a GRE tunnel, the local end of the GRE tunnel sends a keepalive
packet to the remote end every 10s.
A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 266
Jul 24, 2019

Both switches are operating using STP. With exception to those shown, all other default parameters have been
maintained. Which port will be blocked?
A. Port G0/0/1 of switch A.

B. Port G0/0/2 of switch B.
C. Port G0/0/1 of switch B.
D. Port G0/0/2 of switch A.
Correct Answer: C
Section: (none)
Explanation
QUESTION 267
Layer 2 switches are data link layer devices that identify MAC addresses of Layer 2 data frames and forward
Layer 2 data frames based on MAC addresses. In addition, they record mappings between MAC addresses
and interfaces in the MAC address table.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 268
In RSTP mode, both alternate and backup ports cannot forward user traffic but can receive, process, and send
BPDU.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 269
The switch is operating using STP. All default parameters have been maintained. Which port will be assigned a
designated port role?
A. G0/0/1 of switch A.
B. G0/0/2 of switch A.
C. E0/0/1 of the hub.
D. E0/0/2 of the hub.
Correct Answer: A
Section: (none)
Explanation
QUESTION 270
How can the default route be generated? (Choose all that apply.)
A. Manually configured.
B. Automatically generated by the router.
C. Generated by dynamic routing protocols.
D. Generated by link layer protocols.
Correct Answer: AC
Section: (none)
Explanation
QUESTION 271
The following figure shows a routing table. When this router receives a packet with a destination IP address of
9.1.1.1, the router forwards the packet based on the route 9.1.0.0/16 because the matched bit number in this
route is the largest.
Jul 24, 2019

A. True
B. False
Correct Answer: A
Section: (none)
Explanation
QUESTION 272
The routing table includes direct routes and static routes and the preference of the direct routes cannot be
changed.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

QUESTION 273
Host A and Host B use VLAN routing to facilitate communication. When interface G0/0/1.2 of RTA receives a
frame from Host B, what will RTA do?
A. RTA will immediately forward the frame via interface G0/0/1.1.

B. RTA remove the VLAN tag before forwarding the frame.
C. RTA will remove the VLAN tag and add a new tag for VLAN10 before forwarding the frame.
D. RTA will discard the frame.
Correct Answer: B
Section: (none)
Explanation
QUESTION 274
Refer to the configuration output.
Jul 24, 2019

Which of the following statements regarding the configuration output are correct? (Choose all that apply.)
A. The PVID on interface GigabitEthernet0/0/1 is 10.

B. The PVID on interface GigabitEthernet0/0/1 is 1.
C. The PVID on interface GigabitEthernet0/0/2 is 10.
D. The PVID on interface GigabitEthernet0/0/2 is 1.
Correct Answer: AD
Section: (none)
Explanation
QUESTION 275
VLANs 10 and 20 have been created on both SWA and SWC. VLAN 10 has been manually created on SWB.
SWB has learned VLAN 20 from SWA via GVRP, allowing the hosts to belong to different VLANs as shown. If
port Interface G0/0/1 on SWB is changed to fixed mode, what will happen?
A. Host A will still be able to communicate with Host C.

B. Host B will still be able to communicate with Host D.
C. Hosts that belong to the same VLAN will still be able to communicate.
D. All hosts will be unable to communicate with any other host.
Correct Answer: A
Jul 24, 2019

Section: (none)
Explanation
QUESTION 276
On Sx7 series switches, which of the following VLANs can be removed by using command “undo”? (Choose all
that apply.)
A. vlan 1.
B. vlan 2.
C. vlan 1024.
D. vlan 4094.
Correct Answer: BCD

Section: (none)
Explanation
QUESTION 277
A web server in a private network is required to provide HTTP services to public users. The network
administrator is required to configure NAT on RTA. Which configuration should be used?
A. [RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www.inside 192.168.1.1 8080

B. [RTA-Serial0/0/1]nat server protocol tcp global 192.168.1.1 www.inside 202.10.10.1 8080
C. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www.inside 192.168.1.1 8080
D. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www.inside 202.10.10.1 8080
Correct Answer: A
Section: (none)
Explanation
QUESTION 278
On an FR network, when the fr inarp command is executed, the interface where static address mapping entries
have been configured sends an Inverse ARP Request packet to the remote device to replace the static address
mapping entries.
Jul 24, 2019

A. True
B. False
Correct Answer: B
Section: (none)
Explanation
QUESTION 279
According to the configuration on R1 shown in the following figure, the two PCs can correctly access the ISP
network.
A. True
B. False
Correct Answer: A
Section: (none)
Explanation
Jul 24, 2019

HCIA-R&S Dumps v2.2 PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

HCIA-R&S Dumps v2.2 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HCIA-R&S Dumps v2.2 PDF

Uploaded by

Copyright:

Available Formats

H12-211.prepaway.premium.exam.

Huawei Certified Network Associate- Huawei Networking Technology and Device

Jul 24, 2019

What action can be taken? (Choose three)

Correct Answer: ABC

Correct Answer: ABD

Correct Answer: ABC

Jul 24, 2019

Correct Answer: ABD

A. eSight is used to monitor and manage enterprise networks.

Jul 24, 2019

A. A basic ACL value ranges from 1000-2999

A. Packets from network 10.0.1.0/24 network will be denied.

Jul 24, 2019

A. The rule-number of the first rule is 1

Correct Answer: ABC

A. Packets from network 20.1.1.0/24 network will be denied.

Jul 24, 2019

A. Packets from network 172.16.1.1/32 will be denied.

A. Change the work mode to full duplex of each end station.

Jul 24, 2019

A. duplex negotiation auto

What will occur as a result?

A. The end stations cannot communicate.

Which of the following represents this mode?

What can the administrator determine from this?

Jul 24, 2019

Correct Answer: BCD

A. This packets represent a TCP three-way handshake process.

Jul 24, 2019

A. The frame structure of the frame is Ethernet_II

A. The maximum value of TTL is 65535.

Jul 24, 2019

A. Interface for sending an Echo Request packet

Correct Answer: ABD

Jul 24, 2019

A. The source router had shutdown the ICMP function.

Which statement regarding the output is correct?

A. The network administrator used the command ping -c 2 -s 800 10.0.0.2

Jul 24, 2019

Jul 24, 2019

A. The destination IP address of the ARP request is Host C.

Which statement is true about regarding the ARP reply?

Jul 24, 2019

A. ICMP transport packet

Jul 24, 2019

A. Discard the packet.

Which of the following statements is correct?

A. The MAC address of the switch.

Jul 24, 2019

Jul 24, 2019

Jul 24, 2019

A. The source MAC address

Jul 24, 2019

A. Switch A will drop this frame.

Which method can be used to achieve this?

Jul 24, 2019

What is the possible reason for this?