HCD-GRX9000/RX900: Service Manual

HCD-GRX9000/RX900
SERVICE MANUAL East European Model

CIS Model
HCD-RX900
E Model
HCD-GRX9000
HCD-GRX9000/RX900 are the Amplifier,

CD player, Tape Deck and Tuner section
in MHC-GRX9000/RX900. Photo: HCD-RX900
Dolby noise reduction manufactured under license Model Name Using Similar Mechanism HCD-H991AV
from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trade- CD CD Mechanism Type CDM38LH-5BD29AL
marks of Dolby Laboratories Licensing Corporation. Section
Base Unit Type BU-5BD29AL
Optical Pick-up Type KSS-213D/Q-NP
Model Name Using Similar Mechanism HCD-GRX7/RX77S
TAPE
DECK TCM-230AWR1/
Section Tape Transport Mechanism Type
230PWR1
SPECIFICATIONS
– Continued on next page –
MINI Hi-Fi COMPONENT SYSTEM
MICROFILM
Downloaded from www.Manualslib.com manuals search engine

–2–
SECTION 1
TABLE OF CONTENTS SERVICING NOTES
1. SERVICING NOTES ............................................... 3 NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
2. GENERAL
The laser diode in the optical pick-up block may suffer electro-
Location of Controls ....................................................... 6
static break-down because of the potential difference generated
Setting the Time .............................................................. 7
by the charged electrostatic load, etc. on clothing and the human
body.
3. DISASSEMBLY ......................................................... 8 During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
4. TEST MODE .............................................................. 11 repair parts.
The flexible board is easily damaged and should be handled with
5. MECHANICAL ADJUSTMENTS ....................... 13 care.
6. ELECTRICAL ADJUSTMENTS NOTES ON LASER DIODE EMISSION CHECK

DECK Section ................................................................. 13
TUNER Section .............................................................. 16 The laser beam on this model is concentrated so as to be focused
CD Section ...................................................................... 18 on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
7. DIAGRAMS ................................................................. 20 sion, observe from more than 30 cm away from the objective lens.
7-1. Block Diagram – TUNER Section
(East European, CIS models only) – .............................. 21 Notes on chip component replacement
7-2. Block Diagram – CD Section – ...................................... 23 • Never reuse a disconnected chip component.
7-3. Block Diagram – TAPE DECK Section – ...................... 25 • Notice that the minus side of a tantalum capacitor may be dam-
7-4. Block Diagram – MAIN Section (1/2) – ........................ 27 aged by heat.
7-5. Block Diagram – MAIN Section (2/2) – ........................ 29
7-6. Block Diagram – DISPLAY/KEY CONTROL/ Flexible Circuit Board Repairing
POWER SUPPLY Section – ........................................... 31 • Keep the temperature of the soldering iron around 270 ˚C dur-
7-7. Note for Printed Wiring Boards and ing repairing.
Schematic Diagrams ....................................................... 33 • Do not touch the soldering iron on the same conductor of the
7-8. Printed Wiring Board – TUNER Section circuit board (within 3 times).
(East European, CIS models only) – .............................. 34 • Be careful not to apply force on the conductor when soldering
7-9. Schematic Diagram – TUNER Section or unsoldering.
(East European, CIS models only) – .............................. 35
7-10. Printed Wiring Board – CD Section – ........................... 37
7-11. Schematic Diagram – CD Section – ............................... 39 CAUTION
7-12. Printed Wiring Boards – CD MOTOR Section – .......... 41 Use of controls or adjustments or performance of procedures
7-13. Schematic Diagram – CD MOTOR Section – .............. 43 other than those specified herein may result in hazardous ra-
7-14. Printed Wiring Board – TAPE DECK Section – ........... 45 diation exposure.
7-15. Schematic Diagram – TAPE DECK Section – .............. 47
7-16. Printed Wiring Board – LEAF SW Section – ............... 49
7-17. Schematic Diagram – LEAF SW Section – .................. 49
7-18. Printed Wiring Board – MAIN Section – ...................... 51
This appliance is classified as a CLASS 1 LASER product.
7-19. Schematic Diagram – MAIN Section (1/4) – ............... 53
The CLASS 1 LASER PRODUCT MARKING is located on
7-20. Schematic Diagram – MAIN Section (2/4) – ................ 55
the rear exterior.
7-23. Printed Wiring Board – PANEL Section – .................... 61
7-24. Schematic Diagram – PANEL Section – ....................... 63
7-25. Printed Wiring Board – CD-SW Section – .................... 65
7-26. Schematic Diagram – CD-SW Section – ...................... 65
7-27. Printed Wiring Board – HP Section – ........................... 67
7-28. Schematic Diagram – HP Section – .............................. 68 Laser component in this product is capable of emitting radiation
7-29. Printed Wiring Boards – POWER AMP Section – ....... 69 exceeding the limit for Class 1.
7-30. Schematic Diagram – POWER AMP Section – ............ 71
7-31. Printed Wiring Board The following caution label is located inside the unit.
– TRANSFORMER Section – ........................................ 73
7-32. Schematic Diagram
– TRANSFORMER Section – ........................................ 74
7-33. IC Pin Function Description ........................................... 81
8. EXPLODED VIEWS ................................................ 86
9. ELECTRICAL PARTS LIST ............................... 95
–3–
MODEL IDENTIFICATION
– Back Panel –
PART No.
MODEL PART No.

E model 4-996-846-0π
Malaysia, Singapore models 4-996-846-1π
Saudi Arabia model 4-996-846-2π
East European, CIS models 4-996-846-5π
SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
–4–
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF.
1 Remove the Case.
3 Pull-out the disc tray.
2 Turn the cam to the

direction of arrow.
NOTE FOR INSTALLATION (ROTARY ENCODER)
Note:When attaching the Base unit, Insert the

BU cam section A into the groove of BU cam.
Section A
Groove
Note:When attaching the BU cam,

engage the Rotary encoder
switch as shown in the figure.
–5–
SECTION 2
GENERAL
LOCATION OF CONTROLS
1 2 3 4 1 I /u (Power) button
2 DISC 1 to 3 buttons and indicators
3 DISC SKIP/EX-CHANGE button
4 6 (CD) button
5 CD disc tray
5
6 CD ^ button and indicator
!∞ 6
7 TUNER, BAND button
!§ 7
8 r REC button and indicator
!¶ 8 9 P PAUSE button and indicator
9 !º HI-DUB button
!•
!ª !º !¡ CD SYNC button
@º !¡ !™ EFFECT button and indicator
@¡ !£ SURROUND button
@™ !™ !¢ KARAOKE PON/MPX button
!∞ TAPE B 9 and ( buttons and indicators
!£
!§ TAPE A 9 and ( buttons and indicators
@£ !¢
!¶ FUNCTION button
!• MIC LEVEL knob
!ª MIX MIC jac
@º DISPLAY/DEMO button
@¡ CLOCK/TIMER SET button
@™ TIMER SELECT button
@£ p button
@¢
@¢ Fluorescent indicator tube

@∞ ENTER/NEXT button and indicator
@§ GROOVE button and indicator
@¶ VOLUME konb
@• PHONES jack
#º @∞
@ª DBFB button
#¡ #º Remote sensor
#™
#£ @§
#¡ P FILE MEMORY button
#¢ #™ GEQ CONTROL button
#∞ @¶
#£ FILE SELECT button
#§ #¶ @•
#¢ LOOP button
#• @ª
#∞ NON-STOP button and indicator
#ª
#§ FLASH button
#¶ EDIT, DIRECTION button
#• PLAY MODE, DOLBY NR button
#ª REPEAT button
$º § button (deck A)
$¡ Tape deck A
$º $¡ $™ $£ $¢ $∞ $§
$™ –, 0 button and indicator
$£ JOG dial
$¢ +, ) button and indicator
$∞ Tape deck B
$§ § button (deck B)
–6–
–7–
SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
CASE
2 screw 6 case
(CASE3 TP2) (3 × 12)
1 three screws
(BVTT3 × 8)
3 two screws
(CASE3 TP2) (3 × 8)
4 2 screw
(CASE3 TP2) (3 × 12)
5
4
3 two screws
(CASE3 TP2) (3 × 8)
FRONT PANEL SECTION

1 Turn the cam to the direction
of arrow A.
4 loading panel
3 two claws
A
9 screw
(BVTP3 × 10)
5 wire (flat type)

(15 core) (33 cm)
(CN106)
2 Pull-out the
disc tray.
9 screw
(BVTP3 × 10)
7 wire (flat type)

8 connector (17 core) (CN107)
(CN109)
0 three screws 6 wire (flat type) (13 core)
(BVTT3 × 6) (23 cm) (CN201)
–8–
TAPE MECHANISM DECK SECTION (TCM-230AWR1/TCM-230PWR1)
3 three screws
(BVTP3 × 8)
4 two screws
(BVTP3 × 8 )
2 Open the
cassette lids.
5 tape mechanism
deck section
(TCM-230AWR1/
TCM-230PWR1)
1 Push the
cassette lids.
CD MECHANISM DECK SECTION (CDM38LH-5BD29AL)
3 two screws
(BVTP3 × 8)
2 wire (flat type) (19 core) (24 cm)

(CN105)
4 CD mechanism deck section

(CDM38LH-5BD29AL)
Note: The CD mechanism deck will

fall if two screws are removed.
Support it by hand, then remove
three screws.
1 two connectors
(CN103, CN104)
–9–
MAIN BOARD
3 two screws 3 screw

(BVTP3 × 8) (BVTP3 × 8)
2 wire (flat type) (13 core) (14 cm)

(CN102) (E, Thai)
wire (flat type) (15 core) (14 cm)
(CN102) (EXCEPT E, Thai)
1 connector
(CN11)
3 screw
(BVTP3 × 8)
7 connector
(CN110)
6 MAIN board
4 two screws 5 connector

(BVTT3 × 6) (CN101)
– 10 –
SECTION 4
TEST MODE
[MC Cold Reset] [Change-over of AM Tuner Step between 9 kHz and
• The cold reset clears all data including preset data stored in the 10 kHz]
RAM to initial conditions. Execute this mode when returning • A step of AM channels can be changed over between 9 kHz and
the set to the customer. 10 kHz.
Procedure: Procedure:
1. Press three buttons p , [ENTER/NEXT], and I/u simulta- 1. Press I/u button to turn the set ON.
neously. 2. Select the function “TUNER”, and press [TUNER/BAND]
2. The fluorescent indicator tube becomes blank instantaneously, button to select the BAND “AM”.
and the set is reset. 3. Press I/u button to turn the set OFF.
4. Press [ENTER/NEXT] and I/u buttons simultaneously, and
[CD Delivery Mode] the display of fluorescent indicator tube changes to “AM 9 k
• This mode moves the pickup to the position durable to vibra- STEP” or “AM 10 k STEP”, and thus the channel step is
tion. Use this mode when returning the set to the customer after changed over.
repair.
Procedure: [Change-over of LW Tuner Step between 1 kHz and
1. Press I/u button to turn the set ON. 3 kHz]
2. Press [LOOP] button and I/u button simultaneously. • A step of LW channels can be changed over between 1 kHz and
3. A message “LOCK” is displayed on the fluorescent indicator 3 kHz.
tube, and the CD delivery mode is set. Procedure:
1. Press I/u button to turn the set ON.
[MC Hot Reset] 2. Select the function “TUNER”, and press [TUNER/BAND]
• This mode resets the set with the preset data kept stored in the button to select the BAND “LW”.
memory. The hot reset mode functions same as if the power 3. Press I/u button to turn the set OFF.
cord is plugged in and out. 4. Press [ENTER/NEXT] and I/u buttons simultaneously, and
Procedure: the display of fluorescent indicator tube changes to “LW 1 k
1. Press three buttons p , [ENTER/NEXT], and [DISC 1] si- STEP” or “LW 3 k STEP”, and thus the channel step is changed
multaneously. over.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset. [LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
[Sled Servo Mode] Procedure:
• This mode can run the CD sled motor freely. Use this mode, for 1. Press three buttons p , [ENTER/NEXT], and [DISC 2] si-
instance, when cleaning the pickup. multaneously.
Procedure: 2. LEDs and fluorescent indicator tube are all turned on.
1. Press I/u button to turn the set ON. Press [DISC 2] button, and the key check mode is activated.
2. Select the function “CD”. 3. In the key check mode, the fluorescent indicator tube displays
3. Press three buttons p , [ENTER/NEXT], and § simulta- “K 1 J0 V0”. Each time a button is pressed, “K” value in-
neously. creases. However, once a button is pressed, it is no longer taken
4. The Sled Servo mode is selected, if “CD” is blanking on the into account.
fluorescent indicator tube. “J” value increases like 1, 2, 3 ... if rotating [JOG] knob in “+”
5. With the CD in stop status, press ) + button to move the direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
pickup to outside track, or – 0 button to inside track. tion.
6. To exit from this mode, perform as follows: “V” value increases like 1, 2, 3 ... if rotating [VOLUME] knob
1) Move the pickup to the most inside track. in “+” direction, or it decreases like 0, 9, 8 ... if rotating in
2) Press three buttons in the same manner as step 3. “–” direction.
Note: • Always move the pickup to most inside track when exiting from 4. To exit from this mode, press three buttons in the same man-
this mode. Otherwise, a disc will not be unloaded. ner as step 1, or disconnect the power cord.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[Change-over of FUNCTION Name]

• The FUNCTION name of external input terminal can be changed
over to “VIDEO” of “MD”.
Procedure:
1. Press I/u button to turn the set OFF.
2. Press I/u button together with [FUNCTION] button, and the
power is turned on, the display of fluorescent indicator tube
changes to “MD” of “VIDEO” instantaneously, and thus the
FUNCTION is changed over.
– 11 –
[Aging Mode] 4. Aging mode in Tape Deck section
This mode can be used for operation check of CD section and tape 1) Display state
deck section. • No error occurs
• If an error occurred: Display action now
The aging operation stops and display status. • Error occurred
• If no error occurs: Display action last time
The aging operation continues repeatedly.
NO. Display action Action contents Final timing
1. Operating Method of Aging Mode 1 TAPE A AG-1 Rewind the TAPE A The top of tape
1) Set disc in DISC1 tray. 2 TAPE A AG-2 FWD play the TAPE A 2 minutes playing
2) Load the tapes recording use into the decks A and B respec- 3 TAPE A AG-3 F.F. the TAPE A First either 20 seconds
tively. or the end of tape
3) Press three buttons p , [ENTER/NEXT], 4 TAPE A AG-4 REV play the TAPE A 2 minutes playing
and [DISC SKIP/EX-CHANGE] simultaneously. 5 TAPE A AG-5 Rewind the TAPE A The top of tape
4) The aging mode is activated, if a CD roulette mark on the fluo- 6 TAPE B AG-1 Rewind the TAPE B The top of tape
rescent indicator tube is blinking.
7 TAPE B AG-2 FWD play the TAPE B 2 minutes playing
5) To exit from the aging mode, press I/u button to turn the set
8 TAPE B AG-3 F.F. the TAPE B First either 20 seconds
OFF.
or the end of tape
2. Operation Sequence 9 TAPE B AG-4 REV play the TAPE B 2 minutes playing
• During the aging mode in the following sequence to below. 10 TAPE B AG-5 Rewind the TAPE B The top of tape
• Starting the CD section aging for function set “CD”, starting
the TAPE section (deck A) aging for function set “TAPE A” or 2) Operation during Aging Mode
“TAPE B”. (Set another function is no work.) In the aging mode, the program is executed in the following se-
CD (disc1) (12 minutes) → Deck A  quence.
↑ ↓  (Maximum about (1) The tape in deck A is rewound to the head.
Deck B  12 minutes) (2) The FWD side is played back for 2 minutes.
(3) The tape is fast forwarded (FF) for 20 seconds. The follow-
ing procedure is performed when the tape end is reached
3. Aging mode in CD section before the 20 seconds.
1) Display state (4) The REV side is played back for 2 minutes.
• No error occurs (5) The tape is rewound to the head (REW).
display (6) The tape in deck B is rewound to the head.
(7) The FWD side is played back for 2 minutes.
[*][*] 1 – @ @ (8) The tape is fast forwarded (FF) for 20 seconds. The follow-
ing procedure is performed when the tape end is reached
Note: before the 20 seconds.
[*][*] : a letter “CD” and the remainder time (minute) alternately. (re- (9) The REV side is played back for 2 minutes.
mainder time start from 12 minute) (10) The tape is rewound to the head (REW).
@ @ : track number in access.
(11) Aging is switched to the CD player.
• Error occurred
NO. Display Main factor
1 NO DISC ERR Not set disc in DISC1
2 FOCUS1 ERR Focus does not work
3 FOCUS2 ERR Focus does not work after the disc rotate as usual
4 GFS ERR GFS error
5 FBIAS ERR Error in to the focus bias adjustment
6 SENSOR ERR Disc sensor sens DISC1 is no disc
7 TABLE ERR CD tray lotate does not work
8 TRAY ERR Tray (include BD) move does not work
2) Operation during aging Mode

In the aging mode, the program is executed in the following se-
quence.
(1) The CD tray rotates and disc 1 is selected.
(2) Chucking is performed.
(3) TOC is read.
(4) Track 1 played back for 8 seconds.
(5) The CD tray opens and closes again.
(6) 1 to 5 is repeated.
(7) After 12 minutes of aging, aging is switched to the tape deck.
– 12 –
SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution
DECK SECTION 0 dB=0.775 V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head demagne-
record/playback heads pinch rollers tizer.
erase head rubber belts 2. Do not use a magnetized screwdriver for the adjustments.
capstan idlers 3. After the adjustments, apply suitable locking compound to the
2. Demagnetize the record/playback head with a head demagne- parts adjust.
tizer. 4. The adjustments should be performed with the rated power
3. Do not use a magnetized screwdriver for the adjustments. supply voltage unless otherwise noted.
4. After the adjustments, apply suitable locking compound to the 5. The adjustments should be performed in the order given in
parts adjusted. this service manual. (As a general rule, playback circuit ad-
5. The adjustments should be performed with the rated power justment should be completed before performing recording
supply voltage unless otherwise noted. circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-
Torque Measurement CH.
Mode Torque meter Meter reading 7. Switches and controls should be set as follows unless other-
31 to 71 g • cm wise specified.
FWD CQ-102C
(0.43 – 0.98 oz • inch)
FWD 2 to 6 g • cm
• Test Tape
CQ-102C
back tension (0.03 – 0.08 oz • inch) Tape Signal Used for
31 to 71 g • cm P-4-A100 10 kHz, –10 dB Azimuth Adjustment
REV CQ-102RC
(0.43 – 0.98 oz • inch)
WS-48B 3 kHz, 0 dB Tape Speed Adjustment
REV 2 to 6 g • cm
CQ-102RC P-4-L300 315 Hz, 0 dB Level Adjustment
back tension (0.03 – 0.08 oz • inch)
71 to 143 g • cm
FF/REW CQ-201B
(0.99 – 1.99 oz • inch)
Record/Playback Head Azimuth Adjustment
100 g or more
FWD tension CQ-403A
(3.53 oz or more) DECK A DECK B
100 g or more Note: Perform this adjustments for both decks
REV tension CQ-403R
(3.53 oz or more)
Procedure:
1. Mode: Playback (FWD)
test tape MAIN board

P-4-A100 CN301
(10 kHz, –10 dB) Pin 3 (L-CH)
Pin 1 (R-CH) level meter
set
+
–
MAIN board
CN301
Pin 2 (GND)
– 13 –
2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment DECK B
do not match for L-CH and R-CH, turn the adjustment screw Note: Start the Tape Speed adjustment as below after setting to the test
so that outputs match within 1dB of peak. mode.
In the test mode, the tape speed is high during pressing the
[HI-DUB] button.
Procedure:
within
1. Turn the power switch on.
L-CH 1dB 2. Press the p button, [ENTER/NEXT] button and [DISC 3] button
peak simultaneously.
within
Output 1dB (The “VOLUME” on the fluorescent indicator tube will blink
level
while in the test mode.)
To exit from the test mode, press the I/u button.
R-CH Mode: Playback
peak test tape
Screw Screw WS-48B
position L-CH R-CH position (3 kHz, 0 dB) frequency counter
peak peak
set +
3. Mode: Playback (FWD) –
test tape MAIN board

P-4-A100 MAIN board oscilloscope CN301 (Pin 3 : L-CH)
(10 kHz, –10 dB) CN301 (Pin 1 : R-CH)
(pin 3: L-CH)
(pin 2: GND) V H 1. Insert the WS-48B into the deck B.
set 2. Press the · button on the deck B.
3. Press the [HI-DUB] button in playback mode.
Then at HIGH speed mode.
(pin 1: R-CH) 4. Adjust RV1001 on the LEAF SW board do that frequency
counter reads 6,000 ± 180 Hz.
waveform of oscilloscope 5. Press the [HI-DUB] button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency
in phase 45 ° 90 ° 135 ° 180 ° counter reads 3,000 ± 90 Hz.
good wrong Adjustment Location: LEAF SW board
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
(WS-48B)
4. Repeat setps 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the Playback level Adjustment DECK A DECK B
pats adjusted. Procedure:
Mode: Playback
Adjustment Location: Playback Head (Deck A). test tape
Record/Playback/Erase Head (Deck B). P-4-L300 level meter
(315 Hz, 0 dB)
set +
–
MAIN board
CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301

(L-CH) and RV401 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
CN301 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
forward
reverse
– 14 –
REC Bias Adjustment DECK B 4. Mode: Record
Procedure:
MD/VIDEO (AUDIO) IN
INTRODUCTION
315 Hz, 50 mV (–23.8 dB)
When set to the test mode performed in Tape Speed Adjustment, AF OSC
blank tape
when the tape is rewound after recording, the “REC memory mode”
600 Ω CS-123
which rewinds only the recorded portion and playback is set. attenuator
This “REC memory mode” is convenient for performing this ad- + + +
justment. During recording, the input signal FUNCTION will au- – – – set
tomatically switch to VIDEO.
(After recording, press the – 0 button without stopping will 5. Mode: Playback
return to the position where recording was started.) recorded level meter
portion
1. Press [FUNCTION] button to select VIDEO. (This step is not
necessary if the above test mode has already been set.) set +
2. Insert a tape into deck B. –
3. After press [ REC]
r button, press P button, then recording
MAIN board
start. CN301 (Pin 3 : L-CH)
4. Mode: Record (Pin 1 : R-CH)
MD/VIDEO (AUDIO) IN 6. Confirm playback the signal recorded in step 3 become ad-
1) 315 Hz  50 mV (–23.8 dB) justable level as follows.

2) 10 kHz  If these levels do not adjustable level, adjustment the RV301
AF OSC blank tape (L-CH) and RV351 (R-CH) on the MAIN board to repeat steps
600 Ω CN-123 4 and 5.
attenuator Adjustable level:
+ + +
– set CN301 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
– –
Adjustment Location: MAIN board
Adjustment Location:
5. Mode: Playback [MAIN BOARD] (Component Side)
recorded  RV301
portion
level meter  L
REC LEVEL 

1 3  CN106
set + CN301 
–  RV351
 R
MAIN board
CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH) CN107
6. Confirm playback the signal recorded in step 3 become ad-

justable level as follows.
If these levels do not adjustable level, adjustment the RV341
(L-CH) and RV441 (R-CH) on the AUDIO board to repeat
steps 4 and 5.
Adjustable level: Playback output of 315 Hz to playback output
of 10 kHz: ± 1.0 dB
Adjustment Location: AUDIO board
[AUDIO BOARD] (Component Side)
REC Level Adjustment DECK B
Procedure:
INTRODUCTION RV441
When set to the test mode performed in Tape Speed Adjustment, RV401
when the tape is rewound after recording, the “REC memory mode” IC602
CN601 RV311 RV411
which rewinds only the recorded portion and playback is set. RV301
RV341
This “REC memory mode” is convenient for performing this ad-
justment. During recording, the input signal FUNCTION will au- L R R L L R









tomatically switch to VIDEO. PB LEVEL REC BIAS PB LEVEL

(After recording, press the – 0 button without stopping will – DECK B – – DECK A –
return to the position where recording was started.)
[LEAF SW BOARD] (Component Side)
1. Press [FUNCTION] button to select VIDEO. (This step is not
TAPE SPEED
necessary if the above test mode has already been set.)










2. Insert a tape into deck B. (NORMAL) (HIGH)

3. After press [ REC]
r button, press P button, then recording
start. RV1002 RV1001 CN1001
– 15 –
TUNER SECTION 0 dB=1 µV
(East European, CIS models only)
Note: As a front-end (FE1) is difficult to repair if faulty, replace it with
new one.
MW Section Adjustment
Note: FM Tuned Level Adjustment should be performed after this MW
Tuned Level Adjustment.
Setting:
loop antenna
loop antenna (Supplied accessories)
AM RF SSG
set
30% amplitude
modulation by
400 Hz signal 60 cm MW ANTENNA
terminal (TM1)
Field strength dB (µV/m) =SSG output level dB (µV/m) –26 dB.
MW Tuned Level Adjustment

Band: MW
Procedure:
1. Set the output of SSG so that the input level of the set be-
comes 55 dB.
2. Tune the set to 1,050 kHz.
3. Adjust RV41 to the point (moment) when the TUNED indica-
tor will change from going off to going on.
Adjustment Location : TCB board
FM Section Adjustment
Note: This adjustment should be performed after the MW Tuned Level
Adjustment due to the same adjustment element.
Setting:
FM RF stereo signal
generator
75 Ω coaxial
set
Carrier frequency : 98 MHz
Modulation : AUDIO 1 kHz, 75 kHz
deviation (100%) FM ANTENNA terminal
(TM1) (75 Ω open)
FM Tuned Level Adjustment

Band: FM
Procedure:
1. Supply a 25 dBµ 98 MHz signal from the ANTENNA termi-
nal.
2. Tune the set to 98 MHz.
3. If the TUNED indicator does not light, adjust RV42 to the
point (moment) when the TUNED indicator will change from
going off to going on.
Adjustment Location: TCB board
– 16 –
FM Polar Adjustment Procedure :
1. Set the modulation of FM RF SSG to AUDIO 1 kHz, 10 kHz
Connection 1: deviation according to “Connection 1”.
FM RF SSG 2. Tune the set to 69 MHz.
75 Ω coaxial 3. Adjust the RV1702 so that the reading of frequency counter
connected to TP1702 becomes within 31.25 kHz ± 0.05 kHz.
(VCO Adjustment)
set
4. Then record the reading of the level meter connected to TP1701
5. Set the modulation of FM RF SSG to AUDIO 31.25 kHz, 10
FM ANTENNA terminal kHz deviation according to “Connection 2”.
(75 Ω) 6. Tune the set to 69 MHz.
7. Set the CT1701 to be mechanical center.
Output level : 1mV (60dB µ ) (at 75 Ω open) 8. Adjust the L1701 so that the reading of the level meter con-
Modulation : AUDIO 1 kHz, 10kHz deviation nected to TP1701 become maximum.
Then adjust the CT1701 so that the reading of the level meter
Connection 2: connected to TP1701 becomes maximum. (SUB CARRIER
AF OSC PEAK Adjustment)
9. Adjust the RV1701 so that the level at the moment becomes
FM RF SSG 14dB higher value than the level recorded in step 4. (SUB CAR-
75 Ω coaxial RIER LEVEL Adjustment)
set
Audio 31.25 kHz
external
modulation FM ANTENNA terminal
terminal (75 Ω)

Output level : 1mV (60 dB µ) (at 75 Ω open)
Modulation : AUDIO 31.25 kHz, 10 kHz deviation
(EXTERNAL MODULATION)
Adjustment Location :
[TCB BOARD] (Component Side) [TCB BOARD] (Conductor Side)
TM1
RV41
IFT41
MW Tuned Level
Adjustment
IC41 RV42
FM Tuned Level
Adjustment
L1701
Sub Carrier Peak level meter
CN1 Adjustment
RV1701 +
Sub Carrier Level –
Adjustment
TP1701 Q1701
CT1701 (FILTER) frequency
Sub Carrier Peak counter
Adjustment Q1702
RV1702 +
TP1702 –
VCO Adjustment (VCO) Q1703
– 17 –
CD SECTION E-F Balance (Traverse) check
(Without remote commander)
Note:
1. CD Block is basically designed to operate without adjustment. There- oscilloscope
fore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. BD board
3. Use an oscilloscope with more than 10 MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when the TP (TEO) +
TP (VC) –
signal level is low than specified value with the following checks.
S Curve Check Procedure:

oscilloscope 1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on. Press [FUNCTION] button to select
BD board CD.
TP (FEO) + 3. Put disc (YEDS-18) in to play the number five track.
TP (VC) – 4. Press the p button, [ENTER/NEXT] button and ^ but-
ton simultaneously several times to fluorescent indicator tube
Procedure: display “SHUFFLE” is blink. (The sledding servo is turned
1. Connect oscilloscope to test point TP (FEO). OFF.)
2. Connect between test point TP (FOK) and GND by lead wire. 5. Check the level B of the oscilloscope’s waveform and the A
3. Turn Power switch on. (DC voltage) of the center of the Traverse waveform.
4. Put disc (YEDS-18) in and turned Power switch on again and Confirm the following:
actuate the focus search. (Actuate the focus search when disc
A
table is moving in and out.) × 100 = less than ±7 (%)
B
5. Check the oscilloscope waveform (S-curve) is symmetrical
between A and B. And confirm peak to peak level within 3±1
Vp-p. Traverse waveform
Center of the waveform
S-curve waveform
symmetry
B
0V A (DC
A voltage)
within 3 ± 1 Vp-p
B symmetry
level: 500 ± 100 mVp-p
6. Press the p button, [ENTER/NEXT] button and ^ button

6. After check, remove the lead wire connected in step 2. simultaneously several times to fluorescent indicator tube dis-
Note: • Try to measure several times to make sure than the ratio of A : B play “SHUFFLE” is OFF. (The sleding servo is turned ON.)
or B : A is more than 10 : 7. Confirm the C (DC voltage) is almost equal to the A (DC volt-
• Take sweep time as long as possible and light up the brightness
age) is step 5.
to obtain best waveform.
RF Level Check Traverse waveform
oscilloscope
BD board
0V C (DC
TP (RF) + voltage)
TP (VC) –
Sled servo OFF Sled servo ON
Procedure:
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
Note: Clear RF signal waveform means that the shape “≈” can be clearly
distinguished at the center of the waveform.
• FR signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.3 ± 0.3 Vp-p
– 18 –
Adjustment Location:
[BD BOARD] (Conductor Side)
RF
VC
FOK
CNU101
IC101 IC
I02
TEO
FEO
GND
IC103
CNU102
– 19 –
SECTION 7
DIAGRAMS
• Circuit Boards Location
TRANSFORMER board
TCB board
(East European, CIS)
TUNER (FM / AM)
CD-SW board (E, Saudi Arabia, Singapore, Malaysia)
MAIN board
AMP (R) board
PANEL board
HP board AMP (L) board
SENSOR board
MOTOR (TURN) board
CONNECTOR board
BD board
MOTOR (SLIDE) board
AUDIO board
LEAF SW board
– 20 –
HCD-GRX9000/RX900
7-1. BLOCK DIAGRAM – TUNER Section (East European, CIS models only) –
ST +10V • SIGNAL PATH

: FM
Q5
B+ SWITCH
: AM (MW/LW)
FM CIRCUIT B+
TM1
5
ANTENNA
+B CF1 CF3
FM 75Ω 10.7MHz 10.7MHz ST-L
FM IF AMP MPX OUT L LPF41 AMP AMP
COAXIAL
8 ANT IN
FE1
IF OUT 1
Q1 – 4
1 FM-IN FM DET-OUT 23 22
IN
21
L.P.F.
19
IN L OUT L
17 A
FM FRONT-END
(Page 27)
VT
OUT R 20
4
AM
FE2 POLAR /PILOT SWITCH

MW/LW FRONT-END CT1701, L1701, TP1701 POLAR DECODER IC1702
FM/AM IF AMP,
AM RF AMP/MIX/OSC, IC1701
SUB CARRIER
FM/AM DET, MPX PEAK 12
6 12 28 REG IC41 14
2 IN L OUT 7 13
L1701
CT1701
5 13 5
Q9 4 R-CH
LW SWITCH R OUT 6 3
14 3 SUB IN
3 15 C A
TP1701
9 11
2 16
AM IF AM AM 20 SUB IN
AM-MIX 2 4 24
IFT41 IF DET RV1701
VCO STOP 9
SWITCHING
OUT Q1701
SUB CARRIER
ST IND 10
17 29 AM-OSC AM-SD LEVEL
12
MON
VCO
ADJ
26 25 24 23 22 21 20 RV41
AM TUNED STEREO 18 17 D1701 D1702
STEREO 7
LEVEL TUNED
27 AM-RF IN TUNED 6
IF-BUFF MUTE
Q14 RV1702
VCO-STOP
Q13 LW SWITCH AM TP1702 SWITCHING SWITCHING

MW SD 10 9 FM DET Q1702 Q1703
AM/FM
FM SD
SWITCH X42 X41

Q12 450kHz 10.7MHz TP1702, RV1702 D1703
Q11
30 14 15 13
MW MW VCO
SWITCH SWITCH RV42 D41
MUTE
FM TUNED
LEVEL
D42 D43
X21
4.5MHz D1704
10 17 9 11 14 7 2 12 8 1 24 13
ST-CE
FM
VCO STOP
XIN
MW
AM OSC
FM
FM/AM IF
IF REQ
XOUT
FM LOW
MW
VT1
CE 3
FM/AM PLL ST-DOUT
DI 4
IC21 ST-CLK STEREO, TUNED, ST-MUTE,
CL 5
ST-DIN ST-CE, ST-DOUT, ST-CLK, ST-DIN
DO 6 B
05
(Page 27)
– 21 – – 22 –

HCD-GRX9000/RX900
7-2. BLOCK DIAGRAM – CD Section –

DIGITAL SIGNAL PROCESSOR,
CLV SERVO PROCESSOR, FILTER
DIGITAL FILTER, D/A CONVERTER
IC103
PD1 I-V AMP 39 42 38 40
PCMD PCMDI OVER
PD1 52 53
FILI
SERIAL
PCO
FILO
CLTV
4 38 BCK BCKI SAMPLING
54 55 INPUT
LRCK LRCKI INTERFACE DIGITAL
INTERFACE
DETECTOR RF 50 51
RFO RF ASYMMETRY EFM FILTER
INTERNAL BUS
+ SUMMING 33 44 DIGITAL PLL C2PO
D/A
PD2 I-V AMP CORRECTION DEMODULATOR 63
A D AMP RFCK
PD2 RFI 62 NOISE
5 39 32 ASYI WDCK
46 49 SHAPER
ASYO
47
EMPHI
1
I-V AMP
B C PWM &
FOCUS OK FOK FOK INTEGRATOR
2 27 23 73
COMPARATOR
AOUT1
AOUT2
FOCUS OK SUB-CODE
AMP PROCESSOR
F
SERVO AUTO SEQUENCER

DIGITAL DOUT
10 DATA 71 84 95
MIRR DATO OUT
E 22 15 ERROR 16K
RF AMP, AMP TTL TTL CLK CLKO EMPH
6 20 17 CORRECTOR RAM 72
FOCUS/TRACKING GFS
IIL DATA REGISTER
XLT XLTO
SERVO 21 16 61
DEFECT IIL LOCK WFCK
IC101 (1/2) IIL 19 74
AMP XRST GTOP 85 94
23 58
AIN1
AIN2
SENS1 SEIN
IIL 25 13 TIMING CLOCK
C.OUT CNIN DIGITAL CLV CPU INTERFACE
24 14 LOGIC GENERATOR
SENS2 BUFFER
TTL 26
LOUT2
LOUT1
SQSO
SPOD
SCOR
XTAO
SQCK
SBSO
LOCK
XROF
SENS
CLOK
DATA
XRST
EXCK
XLAT
MON
MDS
MDP
XTAI
C4M
CKO
OPTICAL PICK-UP
(KSS-213D/Q-NP) FOCUS FEO FEI FEO
1 FOCUS PHASE
ERROR 2 6
COMPENSATION 100 26 27 28 29 64 8 7 9 10 12 11 75 76 77 21 6 89 90 70 86 93
AMP
FE BIAS
40 X101 R-CH
16.9344MHz
F TRACKING TEO S101
CD-L
41 I-V TEI TRACKING PHASE TAO
E ERROR 45 47 13 (LIMIT)
42 AMP COMPENSATION
AMP SYSTEM CONTROLLER ON : When the optical pick-up
LASER DIODE IC501 (1/3) is inner position.
57 C
XRST (Page 27)
AUTOMATIC LD LD PD
POWER CONTROL 36
AMP AMP
Q101 PD
PD LD SQ-DATA-IN 34
37 OPTICAL
SQ-CLK (D-OUT ON/OFF) 36
TRANSCEIVER
SENS 74 IC381
73 SENS2 CD-DATA 47
CD-CLK 48 IC381
XLT 58 CD DIGITAL
SCOR 18 OUT
OPTICAL
LEVEL SHIFT DISC SENSOR

DISC-SENS 75
Q701 IC703
9
MUTE
DISC TRAY SENSOR
2-AXIS TBL-SENS 76
IC702
DEVICE OUT4A
16 TRACKING IN4A
(TRACKING)
OUT4B 27 S801
15 COIL DRIVE
(FOCUS)
(OPEN/CLOSE DET)
CLOSE
OUT-OPEN 81
OP OP+,
OUT3A OPEN
22, 23
18 FOCUS IN3B OUT OP–

OUT3B 26 24 BUFFER
17 COIL DRIVE
ENC1 80 4 ROTARY
FOCUS/TRACKING COIL DRIVE, ENC2 79 2 ENCODER
SPINDLE/SLED MOTOR DRIVE ENC3 78 3 S811
05 IC102
OUT2A IN2A SLO SLP

M102 11 SLED SLED DISC TRAY SLIDE MOTOR DRIVE
(SLED)
M 12 OUT2B MOTOR DRIVE
6 16
AMP
14
IC801
SLED SERVO FIN OUT1

LOAD-OUT 63 10 MOTOR 7 M801
M101 13
OUT1A
SPINDLE IN1B IC101 (2/2) LOAD-IN 64 2
RIN
DRIVE
OUT2
4
M (DISC TRAY SLIDE)
(SPINDLE) M 14
OUT1B
MOTOR DRIVE
3 • SIGNAL PATH
: CD PLAY
DISC TRAY TURN MOTOR DRIVE
IC701 : DIGITAL OUT
IN1 OUT1
TBL-L 60 3 MOTOR 7 M701
TBL-R 61 6
IN2
DRIVE
OUT2
2
M (DISC TRAY TURN)
– 23 – – 24 –

HCD-GRX9000/RX900
7-3. BLOCK DIAGRAM – TAPE DECK Section –
DECK PROCESS
DECK A/B SELECT, PB/REC EQ AMP,
DOLBY NR AMP, ALC, AMS • SIGNAL PATH
IC301
: PLAYBACK (DECK A)
HP101 DOLBY PASS
(PLAYBACK) : PLAYBACK (DECK B)
70 PB OUT (L) PB-L
PB EQ AMP
L-CH 48
AIN (L)
DOLBY NR
40 D
(DECK A)
AMP
: RECORD
IC611 BIN (L) (Page 27)
46 120 CIRCUIT
RV311
PB LEVEL (L) R-CH +
R-CH R-CH (DECK A)
EQ OUT
L.P.F. ALC (L)
REC OUT (L)

REC
36
ROUT (L)
EQ IN (L)
EQ AMP
ALC (L)
RIN (L)
BIAS (N)
IN (L)
33 BUFFER
ALC
BIAS (C) BIAS
32 CONTROL MAOUT
HRPE101 (1/2) BIAS (M) CIRCUIT
31 28 43 44 35 34 39 38
(RECORD/PLAYBACK)
PB EQ AMP
(DECK B)
L-CH IC601 27
B NORM/CROM
MSIN
REC/PB/PASS
BIAS ON/OFF
NORM/HIGH
RV301
ALC ON/OFF
RM ON/OFF
LM ON/OFF
NR ON/OFF
RV301
A 120/70
PB LEVEL (L) AMS

PB A/B
CIRCUIT REC LEVEL (L)

(DECK B) (DECK B)
R-CH R-CH
MSOUT
REC-L
17 19 15 16 18 20 22 23 24 25 26 E
(Page 28)
REC/PB SWITCHING
IC602 S1004
3 1 (DECK A 120/70)
R-CH R-CH
S1008
(DECK B 120/70)
4
C331, L331 RV1001 RV1002

BIAS
TAPE SPEED TAPE SPEED
TRAP
R-CH (HIGH) (NORMAL)
SL1 SL2
TRIGGER PLUNGER TRIGGER PLUNGER
CAPSTAN MOTOR
DECK A DECK B
CONTROL SWITCH
RV341 Q1001
RV441
REC BIAS (R) REC BIAS (L)
(DECK B) (DECK B) ROTATION ROTATION TRIGGER TRIGGER
DETECT SENSOR DETECT SENSOR PLUNGER DRIVE PLUNGER DRIVE Q335
(DECK A) (DECK B) (DECK A) (DECK B)
REC BIAS B+ IC1001 IC1002 Q333, 334 Q331, 332
SWITCH (A+7V)
Q623
BIAS OSC
HRPE101 (2/2) T621 97 99 94 93 92 90 89 88 87 31 26 27 84 83 82
(ERASE)
CAP-M-H/L
TC-RELAY
ALC-ON/OFF
PB-A/B
EQ-H/N
BIAS
REC-MUTE
NR-ON/OFF
R/P-PASS
TC-MUTE
AMS-IN
A-SHUT
B-SHUT
A-TRG
B-TRG
BIAS OSC CAPSTAN

Q621, 622 CAPM-CNT1P 17 MOTOR DRIVE
Q336 – 339 M1
M (CAPSTAN)
A-PLAY-SW
B-PLAY-SW
SYSTEM CONTROLLER
IC501 (2/3) CAPM-CNT1M 85 CAPSTAN
A-HALF
B-HALF
MOTOR DRIVE
CAPM-CNT2M 86 Q340 – 343
95 96 98 28
S1003 S1006
(DECK A HALF) (DECK B HALF)
05 S1005
(DECK A REC)
S1001 S1002
(DECK A PLAY) (DECK B PLAY)
S1009
(DECK B REC)
– 25 – – 26 –

HCD-GRX9000/RX900
7-4. BLOCK DIAGRAM – MAIN Section (1/2) –
REC-L
E (Page 26)
L J101 (2/2)
MD/VIDEO
J751 (AUDIO) OUT
MIX MIC R-CH R
MIC AMP MIC AMP

IC750 (1/2) IC750 (2/2) R-CH • SIGNAL PATH
RV750
: CD PLAY
LINE AMP J191
MIC LEVEL + IC191 SUPER WOOFER : TAPE PLAY
MUTING
: RECORD
Q191
: TUNER (FM/AM)
CD-L : MIC IN
(Page 24) C 2 58 57 40
VOL OUT2
REC
MIC IN
REC
A2 B2
IN B2
68
PB-L IN C2
(Page 26) D 67
IN A2
INPUT GRAPHIC VOL BUF
69 SELECT F OUT2 IN2 VOLUME BASS BOOST OUT2 L-CH
SOUND EQUALIZER
66
IN D2
CONTROL
+ CONTROL
42 41
CONTROL
CONTROL 36 F (Page 29)
J101 (1/2) CIRCUIT
CIRCUIT CIRCUIT
MD/VIDEO (AUDIO) IN MUTING
Q113
L R-CH
+ R-CH
R-CH
R R-CH CPU
COMMAND
INTERFACE
GRAPHIC EQUALIZER CONTROL,
KEY OUT
KEY IN2
KEY IN1
CLOCK
LATCH
BB B2,
ELECTRICAL VOLUME
BB A2
DATA
IC101
(HCD-RX900)
60 5 75 33 32 34 38, 39
(Page 22)
ST-L
A FEED BACK SWITCH
Q112
FEED-BACK
ANTENNA FM/AM TUNER UNIT + G (Page 29)
FM 75Ω
FM ANT ST-L DBFB CONTROL
SPEANA SWITCH R-CH
FM ANT ST-R R-CH MIXING AMP Q111
IC102
AM ANT ST-MUTE
STEREO R-CH
AM ANT TUNED
SPEANA
AM
ST-DIN
(Page 31) J
ST-DOUT
ST-CLK DATA, CLK
ST-CE
(Page 31) K
MUTING CONTROL
POWER SWITCH
(HCD-GRX9000) (Page 32) L Q571, 572
+5V
CD-POWER
ST-MUTE (Page 32) M
B STEREO
RESET SIGNAL
GENERATOR
(Page 22) TUNED IC502
ST-DOUT
ST-DIN
ST-CLK RESET
N (Page 31)
ST-CE
(HCD-RX900) X501 X502 RESET

DATA
CLK
5MHz 32.768kHz SWITCH

Q501
68 65 66 67 69 70 72 10 11 13 14 46 5 55 56 52 51 3 2 1 16 15
XT1
DBFB-H/L
XT2
X2
X1
ST-MUTE
CD-POWER
POWER
ST-DIN
ST-DOUT
TUNED
IIC-DATA
AC-CUT
ST-CE
ST-CLK
STEREO
IIC-CLK
LINE-MUTE
RESET
M62442-LATCH
M62442-DATA
M62442-CLK
STK-MUTE
STK-MUTE 100 H (Page 29)
SYSTEM CONTROLLER
IC501 (3/3)
RELAY
F-RELAY 6 I (Page 30)
05
– 27 – – 28 –

HCD-GRX9000/RX900
7-5. BLOCK DIAGRAM – MAIN Section (2/2) –
RELAY
I (Page 28)
J421
PHONES
• SIGNAL PATH
: TUNER (FM/AM)
L-CH 1 10 L-CH (+) -1

POWER AMP
F IC801 (1/2) +
(Page 28) L
– TM401
SPEAKER
IMPEDANCE
USE 8 – 16Ω
+ R
17
POWER AMP 13 L-CH (–) -1 –
IC801 (2/2)
FEED BACK D141 OVER LOAD

G + DETECT
FAN MOTOR
Q801, 851 M
DRIVE
(Page 28)
D404
D403
D409
D408
Q401, 402
M401
D811
1 10 R-CH (+) -2 (FAN)
R-CH POWER AMP
IC821 (1/2)
17 13 R-CH (–) -2
POWER AMP
IC821 (2/2)
6
OVER LOAD
DETECT
Q821, 871
STANDBY THP891 RY401 RY402

SWITCH
Q575 TEMPERATURE
DETECT SWITCH
Q891, 892
D831
DC DETECT RELAY DRIVE
STK-MUTE SWITCH Q431
H Q433, 434
(Page 28)
OVER LOAD
PROTECTOR
DETECT SWITCH
05 Q435, 436
Q432, 437
– 29 – – 30 –

HCD-GRX9000/RX900
7-6. BLOCK DIAGRAM – DISPLAY/KEY CONTROL/POWER SUPPLY Section –
POWER
FLUORESCENT INDICATOR TUBE DRIVE, L (Page 27)
LED DRIVE, KEY CONTROL
IC601
CD-POWER
DATA, CLK DATA FLUORESCENT M (Page 27)
K CLK
24 SDA
INDICATOR TUBE
(Page 27) 23 SCL FL601
54 – 69, 72 – 70, 77 – 73
SEG1 – SEG24
RESET
N 10 RESET
(Page 28)
B+
CD MECHANISM DECK
SWITCH
SECTION B+
Q907, 908
BAND-PASS FILTER
IC603
B+
F01 17 34 SPEANA-1
GRID DRIVE AUDIO D+5V SWITCH
F02 16 35 SPEANA-2 GR13 53 Q905, 906 D914
Q621
F03 15 36 SPEANA-3
GR2 – GR12
F04 14 37 SPEANA-4
42 – 52
SPEANA D507
J 4 LINE IN D+5V
(Page 27) L+R 13 32 L+R +5V
SYSTEM CONTROLLER REGULATOR
GRID DRIVE
RST 18 31 SPEANA RESET GR1 41 (IC501) B+ IC902
Q620 D501, 502
+7V
+7V
REGULATOR
(CD M+7V)
IC901
S604 – 625, 631 – 642, B+ SWITCH
D+5V
S656 – 659 Q601, 602
REGULATOR
KEY-0 – KEY-3
Q603 CONTROL SWITCH

26 – 29
Q903
L.SEL 25
+7V
+7V REGULATOR
Q901, 902, 913
POWER TRANSFORMER
LED1, LED5 – LED8,
T11
79, 3 – 6, 15 – 18
TC, PANEL, AUDIO

LED12 – LED15
REMOTE CONTROL
RECEIVER 33 SIRCS LED DRIVE
IC602 D610, 612, 620 – 625, –7V RECT
Q604, 607 – 610,
D631 – 633, 651, 652 –7V REGULATOR D901 – 904
Q613 – 615, 618
Q914, 951, 952
S601 D405 – 407
(JOG DIAL) FAN MOTOR B–
ROTARY 21 JOG-A
= ↔ +
LED9, LED10
ENCODER CAPSTAN MOTOR DRIVE CIRCUIT,

S601 22 JOG-B
11, 12
DJ MIX TRIGGER PLUNGER DRIVE CIRCUIT B+

D613 – 618
S602 ROTARY 19 VOL-A

ENCODER +10V +12V
VOLUME 20 VOL-B +10V RECT
S602 REGULATOR REGULATOR
(FM/AM TUNER CIRCUIT B+) D907, 908
Q909 IC903
X-OUT
–30V
X-IN
–30V RECT
REGULATOR
FL DRIVER (IC601) D909, 910
Q910
8 9
(East European, CIS models)
TO VF1
X601 FLUORESCENT INDICATOR TUBE
05 8MHz (FL601) VF2
AC IN
B+ VOLTAGE
POWER AMP RECT
SELECT SWITCH
(IC801, 821) B– D800
S11
S11
VOLTAGE
SELECTOR
(Except East European, CIS models)
– 31 – – 32 –

7-7. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block.)
Note on Schematic Diagram: Note on Printed Wiring Boards:

• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
and tantalums. • ® : Through hole.
• All resistors are in W and 1/4 W or less unless otherwise • b : Pattern from the side which enables seeing.
specified. (The other layers' patterns are not indicated.)
• ¢ : internal component.
• 2 : nonflammable resistor. Caution:
• 5 : fusible resistor. Pattern face side: Parts on the pattern face side seen from
• C : panel designation. (Side B) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
Note: The components identified by mark ! or dotted line (Side A) the parts face are indicated.
with mark ! are critical for safety.
Replace only with part number specified. • Indication of transistor.
• U : B+ Line. C
• V : B– Line. These are omitted. Q
• H : adjustment for repair.
B E
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc- Q
tion tolerances.
• Waveforms are taken with a oscilloscope. B C E
Voltage variations may be noted due to normal produc-
tion tolerances. These are omitted.
• Circled numbers refer to waveforms.
• Signal path.
F : FM Q
f : AM
E : PB (DECK A) B C E
d : PB (DECK B)
G : REC (DECK B) These are omitted.
J : CD
c : DIGITAL OUT
N : MIC IN
• Abbreviation
EA : Saudi Arabia model.
EE : East European model.
MY : Malaysia model.
SP : Singapore model.
– 33 –
7-8. PRINTED WIRING BOARD – TUNER Section (East European, CIS models only) –
• See page 20 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location
D21 D-1
D41 D-2
D42 E-3
D43 E-3
D1701 F-2
D1702 F-2
D1703 E-2
D1704 F-2
IC21 D-1
IC41 C-3
IC1701 F-1
IC1702 F-3
Q1 D-1
Q2 D-2
Q3 C-2
Q4 C-2
Q5 C-2
Q9 B-1
Q11 B-3
Q12 A-3
Q13 A-2
Q14 A-2
Q1701 E-2
Q1702 F-2
Q1703 F-2
MAIN BOARD
CN102
(Page 52)
– 34 –
HCD-GRX9000/RX900
7-9. SCHEMATIC DIAGRAM – TUNER Section (East European, CIS models only) –
• See page 75 for Waveforms. • See pages 76 and 77 for IC Block Diagrams.
Note on Schematic Diagram:

(Page 57) • Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : MW
< > : LW
∗ : Impossible to measure
– 35 – – 36 –

HCD-GRX9000/RX900
7-10. PRINTED WIRING BOARD – CD Section –

• Semiconductor
Location
Ref. No. Location
IC101 C-5
IC102 B-5
IC103 C-6
Q101 C-3
( )
MAIN BOARD
CN105
(Page 51)
– 37 – – 38 –

HCD-GRX9000/RX900
7-11. SCHEMATIC DIAGRAM – CD Section – • See page 75 for Waveforms. • See pages 78 and 79 for IC Block Diagrams.
(Page 53)
MAIN BOARD
CN105
( )
( )
( )
Note: The components identified by mark ! or dotted line

Replace only with part number specified.
• Voltages and waveforms are dc with respect to ground

under no-signal conditions.
no mark : STOP
( ) : PLAY
– 39 – – 40 –

HCD-GRX9000/RX900
7-12. PRINTED WIRING BOARDS – CD MOTOR Section –

(Page 51)
MAIN BOARD
CN104
(Page 51)
MAIN BOARD
CN103
– 41 – – 42 –

HCD-GRX9000/RX900
7-13. SCHEMATIC DIAGRAM – CD MOTOR Section –

• See page 80 for IC Block Diagrams.
( )
MAIN BOARD
CN104
(Page 53)
MTZJ-T72
–5.6C
( )
MTZJ-T-72-3.6B
MAIN BOARD
CN103
(Page 53)
• Voltages are dc with respect to ground under no-signal
conditions.
no mark : STOP
– 43 – – 44 –

HCD-GRX9000/RX900
7-14. PRINTED WIRING BOARD – TAPE DECK Section –

( )
(Page 51)
MAIN BOARD
CN106
– 45 – – 46 –

HCD-GRX9000/RX900
7-15. SCHEMATIC DIAGRAM – TAPE DECK Section –

• See page 80 for IC Block Diagram.
( )
( )
MAIN BOARD
CN106
(Page 57)


conditions.
no mark : PLAY
( ) : REC
– 47 – – 48 –

HCD-GRX9000/RX900
7-16. PRINTED WIRING BOARD – LEAF SW Section – • See page 20 for Circuit Boards Location.
• Semiconductor Location
( ) Ref. No. Location Ref. No. Location
D141 G-9 Q111 F-9
D333 F-2 Q112 F-9
D334 E-2 Q113 H-8
D401 G-10 Q161 E-8
D402 H-9 Q162 D-8
D403 F-11 Q163 H-8
D404 F-11 Q191 D-11
D405 F-10 Q331 C-2
D406 F-11 Q332 D-2
D407 F-11 Q333 C-2
D408 F-11 Q334 D-2
D409 F-11 Q335 C-1
D501 E-5 Q336 E-2
D502 E-5 Q337 E-2
MAIN BOARD D503 E-5 Q338 F-2
CN107 D504 E-5 Q339 F-2
D505 E-6 Q340 E-2
(Page 51) D506
D507
E-6
E-3
Q341
Q342
E-2
E-2
D508 E-2 Q343 E-2
D901 I-6 Q401 E-11
7-17. SCHEMATIC DIAGRAM – LEAF SW Section – D902 I-5 Q402 E-11
D903 I-6 Q431 G-9
D904 I-6 Q432 H-8
D905 G-6 Q433 H-9
D906 G-7 Q434 H-8
D907 H-4 Q435 H-8
D908 H-4 Q436 G-8
D909 I-5 Q437 G-8
D910 I-4 Q501 E-7
D911 I-4 Q571 E-6
D912 I-4 Q572 E-6
D913 G-3 Q575 F-8
D914 G-5 Q901 F-6
( ) D915 I-3 Q902 G-6
Q903 G-6
IC101 D-9 Q905 F-6
IC102 F-10 Q906 G-6
IC191 D-11 Q907 G-4
IC301 B-2 Q908 G-5
IC381 A-11 Q909 H-4
IC501 D-4 Q910 I-4
IC502 E-6 Q913 G-6
IC901 G-5 Q914 F-7
IC902 G-3 Q951 G-7
IC903 H-3 Q952 G-7
( )
( )
( )
MAIN BOARD
CN107
( )
(Page 57)
( )
( )
( ) ( ) • Voltages are dc with respect to ground under no-signal
conditions.
no mark : PLAY
( ) : REC
– 49 – – 50 –

7-18. PRINTED WIRING BOARD – MAIN Section – HCD-GRX9000/RX900
(Page 34)
(Page 41) (Page 41) (Page 38)
(Page 45)
(Page 49)
(Page 61)
(Page 67)
(Page 73) (Page 70)
– 51 – – 52 –

HCD-GRX9000/RX900
7-19. SCHEMATIC DIAGRAM – MAIN Section (1/4) –
(Page 55)
(Page 40)
(Page 44)
(Page 44)
(Page 59)

(detuned) conditions.
(Page 57) no mark : FM
( ) : CD
– 53 – – 54 –

HCD-GRX9000/RX900
(Page 72)
(Page 54)
(Page 68)
(Page 59)

• Voltages are dc with respect to ground under no-signal Note: The components identified by mark ! or dotted line
(detuned) conditions. with mark ! are critical for safety.
no mark : FM Replace only with part number specified.
– 55 – – 56 –

HCD-GRX9000/RX900
(Page 53)
(Page 35)
(Page 48)
(Page 59)
(Page 50)

no mark: FM [ ] : PB (DECK B)
( ): CD { } : PB (DECK A)
< > : REC
– 57 – – 58 –

7-22. SCHEMATIC DIAGRAM – MAIN Section (4/4) – HCD-GRX9000/RX900
• See page 75 for Waveforms.
(Page 55)
(Page 54)
(Page 58)
(Page 74)
(Page 64)

no mark: FM [ ] : PB (DECK B)
( ): CD { } : PB (DECK A)
– 59 – – 60 – < > : REC

HCD-GRX9000/RX900
7-23. PRINTED WIRING BOARD – PANEL Section –

(Page 51)
(Page 66)
• Semiconductor Location
Ref. No. Location Ref. No. Location Ref. No. Location
D602 D-7 D651 C-1 Q610 C-9
D610 D-5 D652 D-1 Q618 E-1
D612 E-4 Q620 A-7
D613 D-6 IC601 B-6 Q621 A-6
D614 F-6 IC602 A-9
D615 F-6 IC603 B-8
D616 E-9 IC750 C-13
D617 E-4
D618 E-7 Q601 D-6
D620 C-3 Q602 D-7
D621 C-4 Q603 D-7
D622 C-5 Q604 D-5
D623 C-6 Q607 B-3
D624 C-7 Q608 B-3
D625 C-8 Q609 C-6
– 61 – – 62 –

HCD-GRX9000/RX900
7-24. SCHEMATIC DIAGRAM – PANEL Section –
• See page 75 for Waveform. • See page 80 for IC Block Diagrams.
(Page 60)
(Page 65)

• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
– 63 – – 64 – no mark : FM

HCD-GRX9000/RX900
7-25. PRINTED WIRING BOARD – CD-SW Section –

(Page 62)
7-26. SCHEMATIC DIAGRAM – CD-SW Section –
(Page 64)

no mark : FM
– 65 – – 66 –

7-27. PRINTED WIRING BOARD – HP Section –
(Page 51)
– 67 –
7-28. SCHEMATIC DIAGRAM – HP Section –
(Page 56)
– 68 –
HCD-GRX9000/RX900
7-29. PRINTED WIRING BOARDS – POWER AMP Section –

(Page 73)
(Page 69)
• Semiconductor
(Page 70) (Page 70)
Location
AMP (R) BOARD
Ref. No. Location

D821 B-3
D831 C-3
D871 B-2
D891 C-3
D892 B-3
IC821 A-3
Q821 B-3
Q871 B-2
Q891 A-4
Q892 A-4
(Page 69)
• Semiconductor
Location
AMP (L) BOARD
Ref. No. Location
D800 C-4
D801 B-2
D811 D-2
D841 C-3
D842 B-3
D851 E-2 (Page 51)
IC801 C-1
Q801 B-2
Q851 E-2
– 69 – – 70 –

HCD-GRX9000/RX900
7-30. SCHEMATIC DIAGRAM – POWER AMP Section –
(Page 74)
(Page 55)

• Voltages are dc with respect to ground under no-signal Note: The components identified by mark ! or dotted line
(detuned) conditions. with mark ! are critical for safety.
no mark : FM Replace only with part number specified.
– 71 – – 72 –

7-31. PRINTED WIRING BOARD – TRANSFORMER Section –
(Page 51) (Page 70)
– 73 –
7-32. SCHEMATIC DIAGRAM – TRANSFORMER Section –
(Page 72)
(Page 60)

– 74 –
• Waveforms
– TCB Board –
(East European, CIS)
1 IC21 @¢ (XOUT) 4 IC103 @¶ (MDP) 8 IC103 *ª (XTAI)
2.5 Vp-p
2.6 Vp-p
4.2 Vp-p
4.5 MHz 16.9344 MHz

7.8 µs
– BD Board – – MAIN Board –
1 IC101 #£ (RF O) (PLAY MODE) 5 IC103 ^º (XPCK) 1 IC501 !¡ (X1)
1.3
+0.25
–0.20 Vp-p 5 Vp-p
4.4 Vp-p
230 µs 200 ns
2 IC101 2 (FEI) (PLAY MODE) 6 IC103 ^™ (RFCK) 2 IC501 !¢ (XT1)
Approx. 2.2 Vp-p

5 Vp-p
0.5 Vp-p
135 µs 30.6 µs
– PANEL Board –
3 IC101 $¶ (TEI) (PLAY MODE) 7 IC103 &¢ (WFCK) 3 IC601 9 (X-IN)
Approx. 5 Vp-p 3.6 Vp-p

0.2 Vp-p
135 µs 126 ns
– 75 –
• IC Block Diagrams
– TCB Board –
IC21 LC72130 (East European, CIS models)
AOUT2
AOUT1
XOUT
AMIN
FMIN
AIN2
AIN1
VDD
VSS
PD2
PD1
IO2
24 23 22 21 20 19 18 17 16 15 14 13
PHASE DETECTOR
CHARGE PUMP
UNLOCK POWER
DETECTOR ON 1/2
RESET
REFERENCE SWALLOW COUNTER
DIVIDER 1/16, 1/17 4BITS
12BITS PROGRAMMABLE
DRIVER
C 2B UNIVERSAL
I/F DATA SHIFT REGISTER LATCH
COUNTER
1 2 3 4 5 6 7 8 9 10 11 12
XIN
BO5
CE
D1
CL
D0
BO1
BO2
BO3
BO4
IO1
IFIN
IC41 LA1838 (East European, CIS models)

AM-DET OUT
FM-DET OUT
AMP OUT R
AMP OUT L
FM-SD.ADJ
OSC.BUFF
AMP-IN R
AM-RF-IN
AMP-IN L
AM-OSC
FM-AFC
MPX-IN
OUT R
OUT L
REG
AGC
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REG
ALC AM AM AM DECODER
OSC MIX RF. AMP ANTI BIRDIE
BUFF
STEREO
AGC SW
SD
COMP STEREO
DRIVE
AM MUTE
DET
IF FF FF FF
AM/FM AM VCO
PILOT
IF S METER
FM S-CURVE DET
S METER BUFF PHASE
TUNING DET
FM FM DRIVE
IF DET
GND VCC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FM-IN
AM-MIX
FM-IF
AM-IF
GND
TUNED
STEREO
VCC
FM DET
AM. SD
FM. SD
AM. SD ADJ
IF-BUFF
MUTE
AM/FM
VCO-STOP
– 76 –
IC1701 IR3R42 (East European, CIS models) IC1702 µPD4053BC (East European, CIS models)
SUBOUT
SUBIN
LPF1A
LPF1B
LPF2A
LPF2B
DETIN
MON
GND
VCO
B1 1 16 VDD
20 19 18 17 16 15 14 13 12 11
B0 2 15 B.COM
AMP OPEN
1/2 OSC PHASE C1 3 14 A.COM

1/2
COMPARATOR
AMP
PHASE C.COM 4 13 A1
PHASE
COMPARATOR 2 OPEN
TRIGGER CO 5 12 A0
WAVEFORM INH 6 11 A
SEP.
AMP
REGULATOR SAMPLE VEE 7 10 B
GATE & HOLD MUTE OPEN
BUFFER
VSS 8 9 C
1 2 3 4 5 6 7 8 9 10
VCC
IN
POUT
RHC
LHC
ROUT
LOUT
ST
VCO STOP
LAMP
– 77 –
– BD Board –
IC101 CXA1992AR
RF_M
RF_O
RFTC
RF_I
PD2
PD1
CC1
CC2
FOK
PD
LD
CP
CB
39 38 37 36 35 34 33 32 31 30 29 28 27
VEE
–
+
–
+
–
+
–
+
RF SUMMING
PD2 IV PD1 IV
–
+
AMP
AMP AMP
–
+
+
–
FE_BIAS 40 26 SENS2
–
+
VCC +
+
–
APC –
VEE IIL
F 41 – ↓ 25 SENS1
+ LASER POWER CONTROL TTL
F IV AMP VCC
–
+
+
–
+
VCC FE AMP VCC
E 42 – 24 C. OUT
–
+
–
+
+
E IV AMP
VEE
–
+
+
–
DFCT
–
+
EI 43 23 XRST
–
+
IFB4
IFB5
IFB2
IFB3
IFB6
IFB1
BAL1
BAL2
BAL3
BAL4
+
VEE
–
+
–
LEVEL S
VEE
TGFL
VEE
VEE 44 VEE 22 DATA
TOG4
TOG3
TOG2
TOG1
FO. BIAS
–
–
+
+
WINDOW VCC
–
+
MIRR IIL
+ COMP. ↓
–
+
– TTL TTL
TEO 45 + TRK. GAIN FOK ↓ 21 XLT
– WINDOW COMP. IIL
+ +
– –
DFCT1
LDON
E-F BALANCE
MIRR
LPCL
TGFL
LPC
CC1
LPFI 46 + WINDOW COMP. 20 CLK
+
– FOH
–
FOL
TGH
TGL IIL DATA REGISTER
TEI 47 INPUT SHIFT REGISTER 19 LOCK
BALH
– ADDRESS DECODER
+ BALL
SENS SELECTOR
ATSC OUTPUT DECODER
TZC
ATSC 48 – FZC VCC 18 VCC
+
ATSC
WINDOW
COMP.
DFCTO IFB1-6 FS1-4 TG1-2 TM1-7 PS1-4
TZC 49 – BAL1-4 ISET 17 ISET
+ TOG1-4
DFCT
TZC COMP.
TM1
VCC VCC
TDFCT 50 TRACKING 16 SL_O
VCC TG1 PHASE COMPENSATION
TM4 TM6
+
VC 51 – 15 SL_M
VCC
TM7
VCC VEE
FOCUS FS1 TM5
PHASE COMPENSATION TM3 –
FZC 52 + + 14 SL_P
–
VEE VEE
+ FS2 TM2
DFCT – Charge
up FSET
FZC COMP.
TG2
–
FS4
+
VEE
1 2 3 4 5 6 7 8 9 10 11 12 13
FEO
FEI
FDFCT
FGD
FLB
FE_O
FE_M
SRCH
TGU
TG2
FSET
TA_M
TA_O
– 78 –
IC102 BA5941FP-E2
OP IN (–)
OP IN (+)
OP OUT
OUT3A
OUT3B
OUT4A
OUT4B
IN4B
IN4A
IN3B
IN3A
GND
VCC
NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15
NC
– +
Vcc + – + – + – + –
–
+ LEVEL SHIFT
–
+ LEVEL SHIFT
+
LEVEL SHIFT
–
+
LEVEL SHIFT
–
– + + – – + + –
Vcc MUTE Vcc
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VCC
BIAS IN
IN1B
IN1A
IN2B
IN2A
GND
GND
MUTE
VCC
OUT2A
OUT2B
OUT1A
OUT1B
IC103 CXD2519Q PCMDI
EMPHI
PCMD
LRCKI
SYSM
EMPH
WFCK
MNT0
MNT1
MNT3
SCOR
DOUT
SBSO
GTOP
XROF
C2PO
XPCK
XUGF
EXCK
RFCK
XTSL
FSTT
BCKI
C4M
VDD
VDD
VSS
VSS
BCK
GFS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
NC 81 50 LRCK
AVSS 82 49 WDCK
AVDD 83 48 ASYE
AOUT1 84 47 ASYO
– ASYMMETRY
AIN1 85 46 ASYI
– CORRECTOR
PWM
+
3RD-ORDER NOISE SHAPER
LOUT1 86 + 45 BIAS
AVSS 87 44 RF
ERROR
XVDD 88 CORRECTOR 43 AVDD
D/A
XTAI 89 EFM INTERFACE 42 CLTV
DEMODURATOR DIGITAL
XTAO 90 – 41 AVSS
PLL
PWM
XVSS 91 – + 40 FILI
+
AVSS 92 16K RAM DIGITAL OUT 39 FILO
LOUT2 93 38 PCO
AIN2 94 OSC 37 VCTL
AOUT2 95 36 V16M
AVDD 96 35 VCKI
SERIAL-IN OVER SAMPLING SUB CODE
CLOCK
AVSS 97 INTERFACE DIGITAL FILTER PROCESSOR 34 VPCO1
GENERATOR
NC 98 33 VPCO2
NC 99 TIMING SERVO 32 TES1
LOGIC CPU
XRST 100 AUTO DIGITAL CLV 31 TES0
INTERFACE
SEQUENCER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
VDD
VSS
LMUT
RMUT
TES2
CKOUT
SQCK
SQSO
SENS
DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA
SPOB
SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP
MDS
LOCK
PWMI
– 79 –
– MOTOR (TURN) Board – – PANEL Board –
IC701 M54641L IC603 BA3833F-E2
VCC VCC
1 8
RESET 1 RESET 18 RESET
REG 5 REFERENCE C
POWER 2 OUT2 REFFERENCE

IN1 3 INPUT AMP. PREF 2 17 f01
AMP. CURRENT
CONTROL BPF DET

POWER LINE 3 16 f02
INPUT 7 OUT1 NF
IN2 6 AMP.
AMP.
BPF DET
LINE
4 15 f03
4 IN
GND
BPF DET
GND 5 14 f04
BPF DET
BIAS 6 13 f
C Bias
DET
NC 7 12 VCC
NC 8 11 NC
– MOTOR (SLIDE) Board –
IC801 BA6286N NC 9 10 NC
GND 1 PO WER
SAVE
RIN 2
VREF 3
OUT2 4
RNF 5
TSD CONTROL
GND 6 LOGIC
OUT1 7
VM 8
VCC 9
FIN 10
– AUDIO Board –
IC602 µPC1330HA
INVERTER
COMPARATER
1 2 3 4 5 6 7 8 9
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2
– 80 –
7-33. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 µPD780018AYGF-012-3BA (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Function
1 LINE-MUTE O Line muting on/off control signal output terminal “L”: muting on
DBFB normal/high selection signal output to the M62442FP (IC101)
2 DBFB-H/L O
“L”: DBFB high, “H”: DBFB low
3 M62442-LATCH O Serial data latch pulse output to the M62442FP (IC101)
4 KEYCON-LATCH O Serial data latch pulse output terminal Not used (open)
Power on/off control signal output for the audio system (+5V) and deck, panel, audio system
5 POWER O
(+7V) “L”: power on, “H”: standby
6 F-RELAY O Relay drive signal output for the speaker protect “H”: on
7 R-RELAY O Relay drive signal output for the speaker protect “H”: on Not used (open)
8 PL-RELAY O Relay drive signal output for the speaker protect “H”: on Not used (open)
9 VPP — Ground terminal
10 X2 O Main system clock output terminal (5 MHz)
11 X1 I Main system clock input terminal (5 MHz)
12 VDD — Power supply terminal (+5V)
13 XT2 O Sub system clock output terminal (32.768 kHz)
14 XT1 I Sub system clock input terminal (32.768 kHz)
System reset signal input from the reset signal generator (IC502) “L”: reset
15 RESET I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
16 AC-CUT I AC off detection signal input from the reset signal generator (IC502)
17 CAPM-CNT1P O Capstan motor (M1) drive signal output terminal
18 SCOR I Subcode sync (S0+S1) detection signal input from the CXD2519Q (IC103)
19 SOFT-TEST O Output terminal for the software test (open)
20 NCO O Not used (open)
21 RDS-INT I Serial data reading clock signal input terminal Not used (fixed at “L”)
22 RDS-DATA I Serial data input terminal Not used (fixed at “L”)
23 AVDD — Power supply terminal (+5V) (for A/D conversion)
24 AVREF I Reference voltage (+5V) input terminal (for A/D conversion)
25 ADJ I Setting terminal for the CD test mode Normally: fixed at “H”
26 A-SHUT I Shut off detection signal input from the deck-A side reel pulse detector (IC1001)
27 B-SHUT I Shut off detection signal input from the deck-B side reel pulse detector (IC1002)
28 B-HALF I Detection input from the deck-B half detect switch (S1006)
29 CLK-CHECK I Not used (fixed at “L”)
30 SPEC-IN I Setting terminal for the version
31 AMS-IN I Automatic music sensor detection signal input from the HA12215F (IC301)
32 DEMO-CHANGE I Setting terminal for the demonstration H/L Fixed at “L”
33 AVSS — Ground terminal (for A/D conversion)
34 SQ-DATA-IN I Sub-code Q data input from the CXD2519Q (IC103)
SQ-CLK
36 O Sub-code Q data reading clock signal output to the CXD2519Q (IC103)
(D-OUT ON/OFF)
SUPERWOOFER-
37 O Super woofer speaker on/off control signal output terminal Not used (open)
ON/OFF
SUPERWOOFER
38 O Super woofer speaker mode control signal output terminal Not used (open)
MODE
39 NIL I Not used (fixed at “L”)

40 VSS — Ground terminal
41 DELAY-CONT O Serial data latch pulse output terminal Not used (open)
42 PL-LATCH O Serial data latch pulse output terminal Not used (open)
– 81 –
43 COM-DIN I Serial data input terminal Not used (fixed at “L”)
44 COM-DOUT O Serial data output terminal Not used (open)
45 COM-CLK O Serial data transfer clock signal output terminal Not used (open)
Power on/off control signal output for the CD mechanism deck section
46 CD-POWER O
“H”: power on, “L”: standby
47 CD-DATA O Serial data output to the CXD2519Q (IC103)
48 CD-CLK O Serial data transfer clock signal output to the CXD2519Q (IC103)
49 PL-CLK O Serial data transfer clock signal output terminal Not used (open)
50 PL-DATA O Serial data output terminal Not used (open)
51 M62442-CLK O Serial data transfer clock signal output to the M62442FP (IC101)
52 M62442-DATA O Serial data output to the M62442FP (IC101)
53 LEVEL-CONT-A O Level control signal output terminal Not used (open)
54 LEVEL-CONT-B O Level control signal output terminal Not used (open)
55 IIC-DATA I/O Communication data bus with the fluorescent indicator tube driver (IC601)
Communication data reading clock signal input or transfer clock signal output with the fluo-
56 IIC-CLK I/O
rescent indicator tube driver (IC601)
Reset signal output to the CXA1992AR (IC101), BA5941FP (IC102) and CXD2519Q (IC103) on
57 XRST O
the CD mechanism deck section “L”: reset
58 XLT O Serial data latch pulse output to the CXD2519Q (IC103)
59 FOCUS-SW O Focus control signal output terminal Not used (open)
60 TBL-L O Motor drive signal output to the disc tray turn motor driver (IC701) *1
61 TBL-R O Motor drive signal output to the disc tray turn motor driver (IC701) *1
63 LOAD-OUT O Motor drive signal output to the disc tray slide motor driver (IC801) *2
64 LOAD-IN O Motor drive signal output to the disc tray slide motor driver (IC801) *2
65 ST-CLK O PLL serial data transfer clock signal output to the FM/AM tuner unit or PLL (IC21)
66 ST-DIN I PLL serial data input from the FM/AM tuner unit or PLL (IC21)
67 ST-DOUT O PLL serial data output to the FM/AM tuner unit or PLL (IC21)
68 ST-CE O PLL chip enable signal output to the FM/AM tuner unit or PLL (IC21)
69 TUNED I Tuning detection signal input from the FM/AM tuner unit or LA1838 (IC41) “L”: tuned
70 STEREO I FM stereo detection signal input from the FM/AM tuner unit or LA1838 (IC41) “L”: stereo
72 ST-MUTE O Tuner muting control signal output to the FM/AM tuner unit or LA1838 (IC41) “L”: muting on
73 SENS2 I Internal status (SENSE) signal input from the CXA1992AR (IC101)
74 SENS I Internal status (SENSE) signal input from the CXD2519Q (IC103)
*1 Disc tray turn motor (M701) control

Mode COUNTER-
STOP CLOCKWISE BRAKE
Terminal CLOCKWISE
TBL-L (pin ^º) “H” “L” “H” “L”
TBL-R (pin ^¡) “H” “H” “L” “L”
*2 Disc tray slide motor (M801) control

Mode
STOP TABLE IN TABLE OUT BRAKE
Terminal
LOAD-OUT (pin ^£) “H” “H” “L” “L”
LOAD-IN (pin ^¢) “H” “L” “H” “L”
– 82 –
75 DISC-SENS I Disc status detection signal input from the disc sensor (IC703)
76 TBL-SENS I Disc tray status detection signal input from the disc tray sensor (IC702)
77 CAPM-CNT2P O Capstan motor drive signal output terminal Not used (open)
78 ENC3 I
79 ENC2 I Detection signal input from the disc tray address detect rotary encoder (S811)
80 ENC1 I
Detection signal input from the disc tray open/close detect switch (S801)
81 OUT-OPEN I
“L”: open, “H”: close
High/normal speed selection signal output of the capstan motor (M1)
82 CAP-M-H/L O
“L”: high speed, “H”: normal speed
83 B-TRG O Deck-B side trigger plunger (SL2) drive signal output terminal
84 A-TRG O Deck-A side trigger plunger (SL1) drive signal output terminal
85 CAPM-CNT1M O Capstan motor (M1) drive signal output terminal
86 CAPM-CNT2M O Capstan motor (M1) drive signal output terminal
Line muting on/off selection signal output to the HA12215F (IC301)
87 TC-MUTE O
“L”: muting off, “H”: muting on
Recording/playback/pass selection signal output to the HA12215F (IC301)
88 R/P-PASS O
“L”: recording mode
Dolby NR on/off selection signal output to the HA12215F (IC301)
89 NR-ON/OFF O
“L”: dolby off, “H”: dolby on
Recording muting on/off selection signal output to the HA12215F (IC301)
90 REC-MUTE O
“L”: muting on, “H”: muting off
91 CLK-OUT O Clock output for the check Not used (open)
Recording bias on/off selection signal output to the HA12215F (IC301)
92 BIAS O
“L”: bias off, “H”: bias on
Normal/high speed selection signal output to the HA12215F (IC301)
93 EQ-H/N O
“L”: normal speed, “H”: high speed
94 PB-A/B O Deck-A/B selection signal output to the HA12215F (IC301) “L”: deck-A, “H”: deck-B
95 A-PLAY-SW I Detection input from the deck- A play detect switch (S1001) “H”: deck-A play
96 B-PLAY-SW I Detection input from the deck- B play detect switch (S1002) “H”: deck-B play
Recording/playback select signal output to the REC/PB switch (IC602)
97 TC-RELAY O
“L”: playback, “H”: recording
Detection input from the deck-A cassette detect switch (S1003)
98 A-HALF I
“L”: cassette in, “H”: no cassette
99 ALC-ON/OFF O Automatic limiter control signal output to the HA12215F (IC301) “L”: limiter on
100 STK-MUTE O Power amplifier on/off selection signal output terminal “L”: on, “H”: standby
– 83 –
• PANEL BOARD IC601 TMP87CM74AF-6671
(FLUORESCENT INDICATOR TUBE DRIVE, LED DRIVE, KEY CONTROL)

1 LED3 O LED drive signal output terminal Not used (open)
3 LED5 O LED drive signal output terminal (DISC 3)
6 LED8 O LED drive signal output terminal (ENTER/NEXT, GROOVE)
8 X-OUT O System clock output terminal (8 MHz)
9 X-IN I System clock input terminal (8 MHz)
System reset signal input from the reset signal generator (IC502) “L”: reset
10 RESET I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
11 LED9 O LED drive signal output terminal (JOG, DJ MIX)
12 LED10 O LED drive signal output terminal (NON-STOP, + ), – 0)
13 TEST I Connected to ground
15 LED12 O LED drive signal output terminal (EFFECT)
16 LED13 O LED drive signal output terminal (CD ( P)
17 LED14 O LED drive signal output terminal (TAPE B (/9)
18 LED15 O LED drive signal output terminal (TAPE A (/9)
19 VOL-A I Rotary encoder pulse input from the S602 (VOLUME)
20 VOL-B I Rotary encoder pulse input from the S602 (VOLUME)
21 JOG-A I Jog dial pulse input from the S601 (= ↔ + DJ MIX)
22 JOG-B I Jog dial pulse input from the S601 (= ↔ + DJ MIX)
Communication data reading clock signal input or transfer clock signal output with the system
23 SCL I/O
controller (IC501)
24 SDA I/O Communication data bus with the system controller (IC501)
25 L.SEL O LED selection signal output terminal
Key input terminal (A/D input) (S604 to 617)
EFFECT, SURROUND, KARAOKE PON/MPX, p, TIMER SELECT, CLOCK/TIMER SET,
26 KEY-0 I DISPLAY/DEMO, FILE SELECT, GEQ CONTROL, P FILE MEMORY, FUNCTION,
REPEAT STEREO/MONO, EDIT DIRECTION, PLAY MODE DOLBY NR TUNER
MEMORY keys input
27 KEY-1 I
FLASH, NON-STOP, – 0, ENTER/NEXT, + ) , DBFB, GROOVE keys input
28 KEY-2 I TUNER BAND, CD ( P, TAPE B (/9, TAPE A (/9, ON/STANDBY, DISC 1/2/3,
DISC SKIP/EX-CHANGE, 6 keys input
Key input terminal (A/D input) (S618, 656 to 659)
29 KEY-3 I
r REC, P PAUSE, HI-DUB, CD SYNC, keys input
30 MODEL I Destination setting terminal
SPEANA
31 O Reset signal output the spectrum analyzer band-pass filter (IC603) “H”: reset
RESET
Spectrum analyzer drive signal input from the spectrum analyzer band-pass filter (IC603)
32 L+R I
(for VACS, non-stop signal)
33 SIRCS I Remote control signal input from the remote control receiver (IC602)
34 SPEANA-1 I
(for low frequency)
– 84 –
35 SPEANA-2 I
(for low and middle frequency)
36 SPEANA-3 I
(for middle and high frequency)
37 SPEANA-4 I
(for high frequency)
38 VASS — Ground terminal (for A/D conversion)
39 VAREF I Reference voltage (+5V) input terminal (for A/D conversion)
40 VDD — Power supply terminal (+5V)
41 to 53 GR1 to GR13 O Grid drive signal output to the fluorescent indicator tube (FL601)
54 to 69 SEG1 to SEG16 O Segment drive signal output to the fluorescent indicator tube (FL601)
78 VKK — Power supply terminal (–30V) (for fluorescent indicator tube drive)
79 LED1 O LED drive signal output terminal (r REC, P PAUSE)
– 85 –
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by
may have some difference from the original are seldom required for routine service. Some mark ! or dotted line with mark
one. delay should be anticipated when ordering ! are critical for safety.
Replace only with part number
• Color Indication of Appearance Parts these items. specified.
Example: • The mechanical parts with no reference num-
KNOB, BALANCE (WHITE) . . . (RED) ber in the exploded views are not supplied.
↑ ↑ • Hardware (# mark) list and accessories and
Parts Color Cabinet's Color packing materials are given in the last of the
• Abbreviation electrical parts list.
EA : Saudi Arabia
EE : East European
IA : Indonesia
MY : Malaysia
SP : Singapore
(1) CASE SECTION

9
#1
7
5
#3
6
7
Front panel section
4 #3
3
1
#2
#2
2 TCM-230AWR1
#5 TCM-230PWR1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 1-773-025-11 WIRE (FLAT TYPE) (15 CORE) (33cm) 6 1-769-984-11 WIRE (FLAT TYPE) (13 CORE) (23cm)
2 X-4949-350-1 LID (R) ASSY, CASSETTE 7 3-363-099-11 SCREW (CASE 3 TP2) (3X8)
3 1-773-048-11 WIRE (FLAT TYPE) (17 CORE) 8 3-363-099-71 SCREW (CASE 3 TP2) (3X12)
4 X-4949-349-1 LID (L) ASSY, CASSETTE * 9 4-996-728-01 CASE (EXCEPT IA)
5 4-996-703-51 PANEL, LOADING (EE, CIS) * 9 4-996-728-21 CASE (IA)
5 4-996-703-61 PANEL, LOADING (E, EA, MY, SP)
– 86 –
(2) FRONT PANEL SECTION
not supplied
58
57 58
60
#2 58
59
58
58
rA 58
supplied with
J751
58
rB
53 61
(including rA, rB)
62
supplied with J421
58
54
58
#7 not supplied
64
65 57
63
58
56
52
55 #7
54
63
not supplied
51
51 X-4949-385-1 PANEL ASSY, FRONT * 60 1-668-206-11 CD-SW BOARD
52 4-930-336-61 FOOT (FELT) * 61 A-4407-170-A PANEL BOARD, COMPLETE (EE, CIS)
53 4-962-708-11 EMBLEM (4-A), SONY * 61 A-4407-171-A PANEL BOARD, COMPLETE (EA)
54 4-995-081-01 LATCH, DC * 61 A-4407-172-A PANEL BOARD, COMPLETE (E, MY, SP)
55 4-996-722-01 KNOB (VOL) * 62 1-668-209-11 HP BOARD
56 4-996-721-01 KNOB (JOG-U4) * 63 3-973-975-21 DAMPER, OIL

* 57 4-996-716-01 HOLDER (CDM) 64 4-996-732-01 SPRING (A DECK)
58 4-951-620-01 SCREW (2.6X8), +BVTP 65 4-996-733-01 SPRING (B DECK)
59 4-986-893-51 KNOB (MICROPHONE)
– 87 –
(3) CHASSIS SECTION
CDM38LH-5BD29AL 106
#2
#2 #2
#1
105 115
#6
#2
104
M401
#2
T11
#2 B
not supplied 113

A E
#2 103
114
not supplied EA, MY, SP
113
#4
#2 EE, CIS, EA,
108 107 MY, SP
EE, CIS
#4
102 109
101 110
A
#2
111
112
not supplied
– 88 –
* 101 3-703-244-00 BUSHING (2104), CORD (EE, CIS, EA, MY, SP) 108 1-773-008-11 WIRE (FLAT TYPE) (15 CORE) (14cm)
101 3-703-571-11 BUSHING (S) (4516), CORD (E) (EXCEPT E)
* 102 A-4407-181-A AMP (L) BOARD, COMPLETE (EE, CIS) 109 4-924-098-91 HOLDER, PC BOARD (EE, CIS)
* 102 A-4407-182-A AMP (L) BOARD, COMPLETE (E, EA, MY, SP) * 110 A-4407-152-A MAIN BOARD, COMPLETE (EE, CIS)
* 103 A-4407-185-A AMP (R) BOARD, COMPLETE (EE, CIS) * 110 A-4407-153-A MAIN BOARD, COMPLETE (EA, MY, SP)
* 110 A-4407-154-A MAIN BOARD, COMPLETE (E)
* 103 A-4407-186-A AMP (R) BOARD, COMPLETE (E, EA, MY, SP)
* 104 1-668-212-11 TRANSFORMER BOARD 111 4-965-822-01 FOOT
105 1-783-570-11 WIRE (FLAT TYPE) (19 CORE) * 112 4-988-533-01 HOLDER, PWB
* 106 4-996-846-01 PANEL, BACK (E) ! 113 1-575-651-11 CORD, POWER (EE, CIS, EA, MY, SP)
* 106 4-996-846-11 PAENL, BACK (MY, SP) ! 113 1-575-653-11 CORD, POWER (E)
! 114 1-569-008-21 ADAPTOR, CONVERSION 2P (EA, MY, SP)
* 106 4-996-846-21 PANEL, BACK (EA)
* 106 4-996-846-51 PANEL, BACK (EE, CIS) 115 4-999-706-01 COVER (BPAT)
107 1-693-420-11 TUNER (FM/AM) (E) M401 1-763-072-11 FAN, D.C.
107 1-693-421-11 TUNER (FM/AM) (EA, MY, SP) ! T11 1-431-662-11 TRANSFORMER, POWER (EE, CIS)
107 A-4303-587-A TCB BOARD, COMPLETE (EE, CIS) ! T11 1-431-663-11 TRANSFORMER, POWER (EXCEPT EE, CIS)
108 1-769-976-11 WIRE (FLAT TYPE) (13 CORE) (14cm) (E)
The components identified by mark ! or dotted

line with mark ! are critical for safety.
– 89 –
(4) CD MECHANISM DECK SECTION-1
(CDM38LH-5BD29AL)
201
202
201 206
#2
203 M701
204
211 #8
205
207
208
210
212
209
#2
201 4-981-789-11 BRACKET (2), YOKE 208 4-977-941-01 BEARING (WORM)
202 4-977-945-01 TRAY (TURN) * 209 1-658-576-11 SENSOR BOARD
203 X-4946-665-1 SHAFT ASSY, WORM 210 4-934-376-01 SHAFT (ROLLER)
204 4-977-943-01 BELT (TURN) (1.2) 211 4-981-187-01 COLLAR (WORM)
205 4-977-956-01 WHEEL, WORM 212 4-977-944-01 TRAY (SLIDE)
* 206 1-658-577-11 MOTOR (TURN) BOARD M701 A-4672-004-A MOTOR ASSY (TURN)
207 4-988-162-01 ROLLER
– 90 –
(5) CD MECHANISM DECK SECTION-2
(CDM38LH-5BD29AL) 251
251 253 252
255
254
257
258
not
supplied
256
259 270
266
#2
260
267
269
268
261
261 M801
BU-5BD29AL
S811 262
263
#2
263
264
265
251
251 4-981-789-11 BRACKET (2), YOKE * 262 1-658-578-11 MOTOR (SLIDE) BOARD
252 4-977-954-01 PULLEY (SL) 263 4-982-447-01 SPRING (BU), COMPRESSION
253 4-977-953-01 GEAR (SL-A) 264 4-951-620-41 SCREW (2.6), +BVTP
254 4-977-955-01 GEAR (SL-B) 265 X-4949-570-1 HOLDER (BU) ASSY
255 4-977-942-01 BELT (SL) (1.4) 266 4-989-494-01 SCREW (SLIDER), STEP
256 X-4946-667-1 CAM ASSY, BU 267 4-989-492-11 SLIDER (38)

257 1-452-925-21 MAGNET ASSY 268 4-989-819-11 SPRING, TENSION
258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE) 269 4-989-491-11 COVER, LENS
* 259 1-658-575-11 CONNECTOR BOARD 270 4-933-142-21 PULLEY (L), PRESS
* 260 X-4946-668-1 CHASSIS (CDM) ASSY M801 A-4672-004-A MOTOR ASSY (SLIDE)
261 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING S811 1-473-335-11 ENCODER, ROTARY (BU, TRAY ADDRESS DET)
– 91 –
(6) BASE UNIT SECTION
(BU-5BD29AL)
301
302
#9
303
305
M101
M102 304
304
306
307
308

! 301 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP 306 4-917-564-01 GEAR (P), FLATNESS
302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) * 307 A-4699-522-A BD BOARD, COMPLETE
303 4-917-567-01 GEAR (M) 308 4-951-620-01 SCREW (2.6X8), +BVTP
304 4-951-940-01 INSULATOR (BU) M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
305 4-917-565-01 SHAFT, SLED M102 X-4917-504-1 MOTOR ASSY (SLED)
– 92 –
(7) TAPE MECHANISM DECK SECTION-1
 TCM-230AWR1
 TCM-230PWR1
*NOTE: Two types of parts which are not interchangeable are available
for the Head deck (A) ASSY and Head deck (B) ASSY.
When replacing the parts, refer to the following figure, and use
the appropriate part
408
Parts with “P” mark: 230PWR1
Parts without “P” mark: 230AWR1
408
407
406
404
HP101
403
407
HRPE101 403 405

406
404
405
409
402
402
401
401 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 408 3-016-567-01 SPRING (CASSETTE), LEAF
402 3-911-116-21 RIVET, PUSH * 409 A-2007-731-A AUDIO BOARD, COMPLETE
403 3-016-574-01 SPRING (HEAD),TENSION HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR1) (*NOTE)
404 X-3374-156-1 PINCH LEVER (REV) ASSY HP101 A-2056-683-A DECK (A) ASSY, HEAD (230PWR1) (*NOTE)
405 X-3374-155-1 PINCH LEVER (FWD) ASSY HRPE101A-2056-682-A DECK (B) ASSY, HEAD (230AWR1) (*NOTE)
406 3-016-564-01 BASE (PINCH LEVER FWD) HRPE101A-2056-684-A DECK (B) ASSY, HEAD (230PWR1) (*NOTE)
407 3-016-565-01 BASE (PINCH LEVER REV)
– 93 –
(8) TAPE MECHANISM DECK SECTION-2
 TCM-230AWR1
 TCM-230PWR1
*NOTE: Two types of parts which are not interchangeable are available
for the mechanical block assembly. When replacing the parts,
refer to the following figure, and use the appropriate part.
Parts with “P” mark: 230PWR1

Parts without “P” mark: 230AWR1
461
451
#7
462
459
460 463
458
455 #10
#12
#10 #10
#11
460
452 454
456 #10
459
458
464
455
452
M1
456
457
453
* 451 X-3374-214-1 CHASSIS ASSY, MAIN 459 A-2004-630-A MECHANICAL BLOCK ASSY (230PWR1)
452 3-016-570-01 BELT (CAPSTAN) (*NOTE)
453 3-016-569-01 BELT (TENSION) 460 3-016-566-01 SLIDER, REVERSE
454 3-017-360-01 BRACKET (MOTOR) * 461 A-2007-732-A LEAF SW BOARD, COMPLETE
455 X-3374-234-7 FLYWHEEL (FWD) ASSY 462 3-016-575-01 SPRING, TORSION
463 3-019-208-01 WASHER, STOPPER
456 X-3374-235-1 FLYWHEEL (REV) ASSY
457 X-3374-238-1 PULLEY ASSY, TENSION 464 3-027-453-01 SPRING (GROUND), TENSION
458 3-024-405-01 BELT (FR2) M1 A-2004-628-A MOTOR ASSY, CAPSTAN
459 A-2004-629-A MECHANICAL BLOCK ASSY (230AWR1)
(*NOTE)
– 94 –
SECTION 9
ELECTRICAL PARTS LIST AMP (L)
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by
parts list may be different from the parts speci- are seldom required for routine service. mark ! or dotted line with mark
fied in the diagrams or the components used Some delay should be anticipated when order- ! are critical for safety.
Replace only with part number
on the set. ing these items. specified.
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS
may have some difference from the original In each case, u: µ, for example: When indicating parts by reference
one. uA. . : µA. . uPA. . : µPA. . number, please include the board.
• RESISTORS uPB. . : µPB. . uPC. . : µPC. .
All resistors are in ohms. uPD. . : µPD. .
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF
F: nonflammable • COILS
• Abbreviation uH: µH
EA : Saudi Arabia
EE : East European
MY : Malaysia
SP : Singapore
* A-4407-181-A AMP (L) BOARD, COMPLETE (EE, CIS) D841 8-719-911-19 DIODE 1SS119
* A-4407-182-A AMP (L) BOARD, COMPLETE (E, EA, MY,SP) D842 8-719-911-19 DIODE 1SS119
***********************
D851 8-719-911-19 DIODE 1SS119
< CAPACITOR >
< IC >
C801 1-126-963-11 ELECT 4.7uF 20% 50V
C802 1-162-286-31 CERAMIC 220PF 10% 50V IC801 8-749-921-04 IC STK-4211MK-2
C803 1-162-282-31 CERAMIC 100PF 10% 50V
C804 1-104-664-11 ELECT 47uF 20% 10V < TRANSISTOR >
C806 1-126-967-11 ELECT 47uF 20% 50V
Q801 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
C807 1-126-965-11 ELECT 22uF 20% 50V Q851 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
C809 1-126-965-11 ELECT 22uF 20% 50V
C810 1-164-159-11 CERAMIC 0.1uF 50V < RESISTOR >
C811 1-136-495-11 FILM 0.068uF 5% 50V
C812 1-136-495-11 FILM 0.068uF 5% 50V R801 1-249-417-11 CARBON 1K 5% 1/4W
R802 1-249-438-11 CARBON 56K 5% 1/4W
C813 1-162-306-11 CERAMIC 0.01uF 20% 16V R803 1-249-415-11 CARBON 680 5% 1/4W
C842 1-126-307-11 ELECT 6800uF 20% 50V R805 1-260-107-11 CARBON 4.7K 5% 1/2W
C843 1-126-934-11 ELECT 220uF 20% 10V
C851 1-126-963-11 ELECT 4.7uF 20% 50V R806 1-260-107-11 CARBON 4.7K 5% 1/2W
! R807 1-212-881-11 FUSIBLE 100 5% 1/4W F
C852 1-162-286-31 CERAMIC 220PF 10% 50V ! R808 1-220-893-11 METAL 0.22 10% 5W F
C853 1-162-282-31 CERAMIC 100PF 10% 50V R809 1-260-076-11 CARBON 10 5% 1/2W
C854 1-104-664-11 ELECT 47uF 20% 10V R811 1-249-417-11 CARBON 1K 5% 1/4W
C856 1-126-967-11 ELECT 47uF 20% 50V
R813 1-249-441-11 CARBON 100K 5% 1/4W
C861 1-136-495-11 FILM 0.068uF 5% 50V R816 1-260-105-11 CARBON 3.3K 5% 1/2W
C862 1-136-495-11 FILM 0.068uF 5% 50V ! R820 1-202-972-61 FUSIBLE 1 5% 1/4W F
C891 1-136-165-00 FILM 0.1uF 5% 50V
(EE, CIS)
< CONNECTOR > R841 1-249-428-11 CARBON 8.2K 5% 1/4W
(EXCEPT EE, CIS)
CN801 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P R842 1-249-429-11 CARBON 10K 5% 1/4W
CN803 1-691-767-11 PLUG (MICRO CONNECTOR) 5P (EE, CIS)
CN804 1-691-765-11 PLUG (MICRO CONNECTOR) 3P R842 1-249-431-11 CARBON 15K 5% 1/4W
CN805 1-691-765-21 PLUG (MICRO CONNECTOR) 3P (EXCEPT EE, CIS)
R843 1-247-895-00 CARBON 470K 5% 1/4W
< DIODE > (EE, CIS)
D800 8-719-060-53 DIODE RBV-2506 R843 1-247-897-11 CARBON 560K 5% 1/4W

D801 8-719-911-19 DIODE 1SS119 (EXCEPT EE, CIS)
D811 8-719-911-19 DIODE 1SS119
– 95 –
AMP (L) AMP (R)
R844 1-249-425-11 CARBON 4.7K 5% 1/4W Q871 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
(EE, CIS) Q891 8-729-029-86 TRANSISTOR DTC124ESA
R844 1-249-430-11 CARBON 12K 5% 1/4W Q892 8-729-620-05 TRANSISTOR 2SC2603-EF
(EXCEPT EE, CIS)
R851 1-249-417-11 CARBON 1K 5% 1/4W < RESISTOR >
R852 1-249-438-11 CARBON 56K 5% 1/4W
R821 1-249-417-11 CARBON 1K 5% 1/4W
R853 1-249-415-11 CARBON 680 5% 1/4W R822 1-249-438-11 CARBON 56K 5% 1/4W
R854 1-249-438-11 CARBON 56K 5% 1/4W R823 1-249-415-11 CARBON 680 5% 1/4W
R855 1-260-107-11 CARBON 4.7K 5% 1/2W R824 1-249-438-11 CARBON 56K 5% 1/4W
R856 1-260-107-11 CARBON 4.7K 5% 1/2W R825 1-260-107-11 CARBON 4.7K 5% 1/2W
! R857 1-212-881-11 FUSIBLE 100 5% 1/4W F
R826 1-260-107-11 CARBON 4.7K 5% 1/2W
! R858 1-220-893-11 METAL 0.22 10% 5W F ! R827 1-212-881-11 FUSIBLE 100 5% 1/4W F
R859 1-260-076-11 CARBON 10 5% 1/2W ! R828 1-220-893-11 METAL 0.22 10% 5W F
R861 1-249-417-11 CARBON 1K 5% 1/4W R831 1-249-417-11 CARBON 1K 5% 1/4W
R862 1-249-431-11 CARBON 15K 5% 1/4W
R832 1-249-431-11 CARBON 15K 5% 1/4W
************************************************************ R834 1-260-105-11 CARBON 3.3K 5% 1/2W
R836 1-260-105-11 CARBON 3.3K 5% 1/2W
* A-4407-185-A AMP (R) BOARD, COMPLETE (EE, CIS) ! R840 1-202-972-61 FUSIBLE 1 5% 1/4W F
* A-4407-186-A AMP (R) BOARD, COMPLETE (E, EA, MY,SP)
*********************** R871 1-249-417-11 CARBON 1K 5% 1/4W
R872 1-249-438-11 CARBON 56K 5% 1/4W
< CAPACITOR > R873 1-249-415-11 CARBON 680 5% 1/4W
R874 1-249-438-11 CARBON 56K 5% 1/4W
C822 1-162-286-31 CERAMIC 220PF 10% 50V
C823 1-162-282-31 CERAMIC 100PF 10% 50V R876 1-260-107-11 CARBON 4.7K 5% 1/2W
C824 1-104-664-11 ELECT 47uF 20% 10V ! R877 1-212-881-11 FUSIBLE 100 5% 1/4W F
C826 1-126-967-11 ELECT 47uF 20% 50V ! R878 1-220-893-11 METAL 0.22 10% 5W F
R879 1-260-076-11 CARBON 10 5% 1/2W
C829 1-126-965-11 ELECT 22uF 20% 50V
C830 1-164-159-11 CERAMIC 0.1uF 50V R882 1-249-431-11 CARBON 15K 5% 1/4W
R891 1-249-427-11 CARBON 6.8K 5% 1/4W
C833 1-162-306-11 CERAMIC 0.01uF 20% 16V (EE, CIS)
C872 1-162-286-31 CERAMIC 220PF 10% 50V (EXCEPT EE, CIS)
C873 1-162-282-31 CERAMIC 100PF 10% 50V
(EE, CIS)
C877 1-126-965-11 ELECT 22uF 20% 50V (EXCEPT EE, CIS)
C878 1-126-963-11 ELECT 4.7uF 20% 50V R893 1-247-895-00 CARBON 470K 5% 1/4W
C881 1-136-495-11 FILM 0.068uF 5% 50V (EE, CIS)
(EXCEPT EE, CIS)
(EE, CIS)
< DIODE >
R894 1-249-430-11 CARBON 12K 5% 1/4W
D821 8-719-911-19 DIODE 1SS119 (EXCEPT EE, CIS)
D831 8-719-911-19 DIODE 1SS119 R895 1-249-441-11 CARBON 100K 5% 1/4W
D892 8-719-911-19 DIODE 1SS119
< THERMISTOR >
< IC >
THP891 1-807-796-11 THERMISTOR
IC821 8-749-921-04 IC STK-4211MK-2 ************************************************************
< TRANSISTOR >
Q821 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA

– 96 –
AUDIO BD
* A-2007-731-A AUDIO BOARD, COMPLETE Q622 8-729-142-46 TRANSISTOR 2SC2001-LK
********************** Q623 8-729-801-93 TRANSISTOR 2SD1387
< CAPACITOR > < RESISTOR >
C301 1-162-289-31 CERAMIC 390PF 10% 50V R301 1-247-881-00 CARBON 120K 5% 1/4W
C302 1-126-968-11 ELECT 100uF 20% 6.3V R302 1-249-409-11 CARBON 220 5% 1/4W
C304 1-130-483-00 MYLAR 0.01uF 5% 50V R304 1-247-889-00 CARBON 270K 5% 1/4W
C331 1-137-427-11 FILM 120PF 5% 50V R331 1-249-430-11 CARBON 12K 5% 1/4W
C402 1-126-968-11 ELECT 100uF 20% 6.3V R404 1-247-889-00 CARBON 270K 5% 1/4W
C405 1-107-715-11 ELECT 22uF 20% 16V R412 1-247-807-31 CARBON 100 5% 1/4W
C413 1-162-282-31 CERAMIC 100PF 10% 50V R415 1-247-850-11 CARBON 6.2K 5% 1/4W
C431 1-137-427-11 FILM 120PF 5% 50V R602 1-249-409-11 CARBON 220 5% 1/4W
C611 1-104-396-11 ELECT 10uF 20% 16V ! R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
C612 1-104-396-11 ELECT 10uF 20% 16V ! R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
C622 1-126-961-11 ELECT 2.2uF 20% 50V R624 1-249-432-11 CARBON 18K 5% 1/4W
C624 1-130-481-00 MYLAR 0.0068uF 5% 50V
C625 1-130-481-00 MYLAR 0.0068uF 5% 50V < VARIABLE RESISTOR >
C627 1-124-903-11 ELECT 1uF 20% 50V
C628 1-136-153-00 FILM 0.01uF 5% 50V RV301 1-238-598-11 RES, ADJ, CARBON 2.2K
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K
C642 1-104-664-11 ELECT 47uF 20% 16V RV341 1-241-768-11 RES, ADJ, CARBON 220K
< CONNECTOR > RV411 1-238-598-11 RES, ADJ, CARBON 2.2K
CN601 1-695-338-11 PIN, CONNECTOR (PC BOARD) 15P RV441 1-241-768-11 RES, ADJ, CARBON 220K
< IC > < TRANSFORMER >
IC601 8-759-111-44 IC uPC4570C-1 T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION

IC602 8-759-143-54 IC uPC1330HA ************************************************************
IC611 8-759-111-44 IC uPC4570C-1
* A-4699-522-A BD BOARD, COMPLETE
< COIL > *******************
L331 1-410-780-11 INDUCTOR 27mH < CAPACITOR >

L431 1-410-780-11 INDUCTOR 27mH
L601 1-414-193-41 INDUCTOR 220uH C101 1-126-607-11 ELECT CHIP 47uF 20% 4V
L602 1-414-193-41 INDUCTOR 220uH C102 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V
< TRANSISTOR > C105 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C106 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
Q621 8-729-142-46 TRANSISTOR 2SC2001-LK

– 97 –
BD
C107 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V < FERRITE BEAD >
C109 1-163-021-00 CERAMIC CHIP 0.01uF 10% 50V FB101 1-414-234-11 INDUCTOR CHIP 0UH
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V FB103 1-414-234-11 INDUCTOR CHIP 0UH
< IC >
C113 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V IC101 8-752-080-62 IC CXA1992AR
C114 1-164-005-11 CERAMIC CHIP 0.47uF 25V IC102 8-759-429-32 IC BA5941FP-E2
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V IC103 8-752-380-64 IC CXD2519Q
< SHORT >
C117 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C118 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V JW101 1-216-295-00 SHORT 0
C119 1-163-038-00 CERAMIC CHIP 0.1uF 25V JW104 1-216-295-00 SHORT 0
C120 1-124-779-00 ELECT CHIP 10uF 20% 16V
C121 1-163-038-00 CERAMIC CHIP 0.1uF 25V < TRANSISTOR >
C122 1-163-021-00 CERAMIC CHIP 0.01uF 10% 50V Q101 8-729-010-08 TRANSISTOR MSB710-R
C124 1-126-607-11 ELECT CHIP 47uF 20% 4V < RESISTOR >
C126 1-163-038-00 CERAMIC CHIP 0.1uF 25V R102 1-216-001-00 METAL CHIP 10 5% 1/10W
R104 1-216-093-00 METAL CHIP 68K 5% 1/10W
C127 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V R105 1-216-088-00 METAL CHIP 43K 5% 1/10W
C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V R106 1-216-088-00 METAL CHIP 43K 5% 1/10W
C129 1-163-038-91 CERAMIC CHIP 0.1uF 25V R107 1-216-088-00 METAL CHIP 43K 5% 1/10W
C131 1-164-346-11 CERAMIC CHIP 1uF 16V R108 1-216-088-00 METAL CHIP 43K 5% 1/10W
R109 1-216-093-00 METAL CHIP 68K 5% 1/10W
C161 1-164-005-11 CERAMIC CHIP 0.47uF 25V R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
C163 1-163-117-00 CERAMIC CHIP 100PF 5% 50V R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R118 1-216-063-00 RES, CHIP 3.9K 5% 1/10W
C165 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V R120 1-216-089-00 RES, CHIP 47K 5% 1/10W
C166 1-163-137-00 CERAMIC CHIP 680PF 5% 50V R121 1-216-114-00 RES, CHIP 510K 5% 1/10W
C167 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
C168 1-163-137-00 CERAMIC CHIP 680PF 5% 50V R122 1-216-097-00 RES, CHIP 100K 5% 1/10W
R123 1-216-099-00 METAL CHIP 120K 5% 1/10W
C171 1-163-237-11 CERAMIC CHIP 27PF 5% 50V R126 1-216-063-00 RES, CHIP 3.9K 5% 1/10W
C174 1-163-038-00 CERAMIC CHIP 0.1uF 25V R127 1-216-089-00 RES, CHIP 47K 5% 1/10W
R128 1-216-098-00 METAL CHIP 110K 5% 1/10W
C175 1-163-038-00 CERAMIC CHIP 0.1uF 25V R129 1-216-025-00 RES, CHIP 100 5% 1/10W
C179 1-163-038-00 CERAMIC CHIP 0.1uF 25V R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
C181 1-126-205-11 ELECT CHIP 47uF 20% 6.3V R134 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
C182 1-126-393-11 ELECT CHIP 33uF 20% 10V R135 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
C183 1-124-778-00 ELECT CHIP 22uF 20% 6.3V R136 1-216-073-00 METAL CHIP 10K 5% 1/10W
R138 1-216-025-00 RES, CHIP 100 5% 1/10W
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
< CONNECTOR > R158 1-216-001-00 METAL CHIP 10 5% 1/10W
CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P R159 1-216-121-00 RES, CHIP 1M 5% 1/10W
CNU102 1-778-874-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P R161 1-216-097-00 RES, CHIP 100K 5% 1/10W
R162 1-216-073-00 METAL CHIP 10K 5% 1/10W
R163 1-216-121-00 RES, CHIP 1M 5% 1/10W
R164 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
– 98 –
BD CD-SW CONNECTOR HP LEAF SW
R165 1-216-049-11 RES, CHIP 1K 5% 1/10W S640 1-762-875-21 SWITCH, KEYBOARD (DISC 3)
R166 1-216-073-00 METAL CHIP 10K 5% 1/10W S641 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)
R167 1-216-081-00 METAL CHIP 22K 5% 1/10W
R168 1-216-073-00 METAL CHIP 10K 5% 1/10W S642 1-762-875-21 SWITCH, KEYBOARD (6)
R169 1-216-079-00 METAL CHIP 18K 5% 1/10W ************************************************************
R170 1-216-081-00 METAL CHIP 22K 5% 1/10W * 1-658-575-11 CONNECTOR BOARD

R171 1-216-073-00 METAL CHIP 10K 5% 1/10W *****************
R172 1-216-079-00 METAL CHIP 18K 5% 1/10W
R173 1-216-025-00 RES, CHIP 100 5% 1/10W < CONNECTOR >
R174 1-216-033-00 METAL CHIP 220 5% 1/10W
* CN701 1-568-946-11 PIN, CONNECTOR 8P
R175 1-216-025-00 RES, CHIP 100 5% 1/10W CN702 1-750-413-11 CONNECTOR, FFC/FPC 8P
R176 1-216-025-00 RES, CHIP 100 5% 1/10W
R177 1-216-025-00 RES, CHIP 100 5% 1/10W < RESISTOR >
R178 1-216-025-00 RES, CHIP 100 5% 1/10W
R179 1-216-025-00 RES, CHIP 100 5% 1/10W R703 1-249-435-11 CARBON 33K 5% 1/4W
R704 1-249-429-11 CARBON 10K 5% 1/4W
R180 1-216-025-00 RES, CHIP 100 5% 1/10W R705 1-249-417-11 CARBON 1K 5% 1/4W
R181 1-216-025-00 RES, CHIP 100 5% 1/10W ************************************************************
R188 1-216-037-00 METAL CHIP 330 5% 1/10W
R190 1-216-097-00 RES, CHIP 100K 5% 1/10W * 1-668-209-11 HP BOARD
R191 1-216-105-00 RES, CHIP 220K 5% 1/10W *********
< SWITCH > < CAPACITOR >
S101 1-572-085-11 SWITCH, LEAF (LIMIT) C421 1-162-294-31 CERAMIC 0.001uF 10% 50V
C471 1-162-294-31 CERAMIC 0.001uF 10% 50V
< VIBRATOR > C472 1-164-159-11 CERAMIC 0.1uF 50V
X101 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz) < CONNECTOR >

************************************************************
* CN109 1-564-521-11 PLUG, CONNECTOR 6P
* 1-668-206-11 CD-SW BOARD
*********** < LEAD >
< DIODE > EL1 1-690-880-41 LEAD (WITH CONNECTOR)
D631 8-719-056-13 LED SML79423C-TP15 (DISC 1) < JACK >

D632 8-719-056-13 LED SML79423C-TP15 (DISC 2)
D633 8-719-056-13 LED SML79423C-TP15 (DISC 3) J421 1-784-224-11 JACK (LARGE TYPE) (PHONES)
************************************************************
< TRANSISTOR >
* A-2007-732-A LEAF SW BOARD, COMPLETE
Q613 8-729-029-68 TRANSISTOR DTC114TSA ************************
Q614 8-729-029-68 TRANSISTOR DTC114TSA
Q615 8-729-029-68 TRANSISTOR DTC114TSA < CAPACITOR >
< RESISTOR > C1001 1-107-716-11 ELECT 33uF 20% 10V
R656 1-249-421-11 CARBON 2.2K 5% 1/4W < CONNECTOR >

R657 1-249-422-11 CARBON 2.7K 5% 1/4W
R658 1-249-424-11 CARBON 3.9K 5% 1/4W CN1001 1-568-860-11 SOCKET, CONNECTOR 17P
R659 1-249-426-11 CARBON 5.6K 5% 1/4W CN1001 1-784-459-11 CONNECTOR, FFC/FPC 17P
R660 1-249-428-11 CARBON 8.2K 5% 1/4W
< DIODE >
R691 1-247-804-11 CARBON 75 5% 1/4W
R692 1-247-804-11 CARBON 75 5% 1/4W D1001 8-719-911-19 DIODE 1SS119
R694 1-247-804-11 CARBON 75 5% 1/4W
R695 1-247-804-11 CARBON 75 5% 1/4W < CABLE HOLDER >
R696 1-247-804-11 CARBON 75 5% 1/4W * DM1001 1-784-581-11 HOLDER, CABLE (2.5MM PITCH) 4P
< SWITCH > < PHOTO INTERRUPTER >
S637 1-762-875-21 SWITCH, KEYBOARD (I/u(POWER)) IC1001 8-749-014-38 PHOTO INTERRUPTER SG-264
S638 1-762-875-21 SWITCH, KEYBOARD (DISC 1) IC1002 8-749-014-38 PHOTO INTERRUPTER SG-264
S639 1-762-875-21 SWITCH, KEYBOARD (DISC 2)
– 99 –
LEAF SW MAIN
< TRANSISTOR > C133 1-164-159-11 CERAMIC 0.1uF 50V
C134 1-164-159-11 CERAMIC 0.1uF 50V
Q1001 8-729-029-56 TRANSISTOR DTA144ESA C135 1-126-964-11 ELECT 10uF 20% 50V
Q1001 8-729-900-65 TRANSISTOR DTA144ES C136 1-164-159-11 CERAMIC 0.1uF 50V
C141 1-126-959-11 ELECT 0.47uF 20% 50V
< RESISTOR >
C151 1-162-286-31 CERAMIC 220PF 10% 50V
R907 1-247-879-11 CARBON 100K 5% 1/4W C152 1-162-286-31 CERAMIC 220PF 10% 50V
R1001 1-249-409-11 CARBON 220 5% 1/4W C161 1-137-195-11 FILM 0.56uF 5% 50V
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W
C164 1-130-480-00 MYLAR 0.0056uF 5% 50V
R1006 1-247-864-11 CARBON 24K 5% 1/4W C166 1-130-473-00 MYLAR 0.0015uF 5% 50V
R1007 1-247-856-00 CARBON 11K 5% 1/4W C167 1-136-153-00 FILM 0.01uF 5% 50V
R1008 1-249-417-11 CARBON 1K 5% 1/4W C168 1-130-467-00 MYLAR 470PF 5% 50V
< VARIABLE RESISTOR > C169 1-130-479-00 MYLAR 0.0047uF 5% 50V

C170 1-136-153-00 FILM 0.01uF 5% 50V
RV1001 1-241-785-11 RES, ADJ, CARBON 10K C171 1-126-964-11 ELECT 10uF 20% 50V
RV1002 1-241-785-11 RES, ADJ, CARBON 10K C172 1-162-291-31 CERAMIC 560PF 10% 50V
C173 1-136-165-00 FILM 0.1uF 5% 50V
< SWITCH >
C174 1-136-165-00 FILM 0.1uF 5% 50V
S1001 1-570-953-11 SWITCH, PUSH (1 KEY) (A PLAY) C175 1-126-964-11 ELECT 10uF 20% 50V
S1002 1-570-953-11 SWITCH, PUSH (1 KEY) (B PLAY) C176 1-136-495-11 FILM 0.068uF 5% 50V
S1003 1-771-333-11 SWITCH, LEAF (A HALF) C177 1-136-153-00 FILM 0.01uF 5% 50V
S1004 1-771-205-11 SWITCH, LEAF (A 120/70) C191 1-126-964-11 ELECT 10uF 20% 50V
S1005 1-771-205-11 SWITCH, LEAF (REC A)
C192 1-162-292-31 CERAMIC 680PF 10% 50V
S1006 1-771-333-11 SWITCH, LEAF (B HALF) C193 1-126-964-11 ELECT 10uF 20% 50V
S1008 1-771-205-11 SWITCH, LEAF (B 120/70) C194 1-162-286-31 CERAMIC 220PF 10% 50V
S1009 1-771-205-11 SWITCH, LEAF (REC B) C195 1-162-306-11 CERAMIC 0.01uF 20% 16V
************************************************************ C196 1-162-306-11 CERAMIC 0.01uF 20% 16V
* A-4407-152-A MAIN BOARD, COMPLETE (EE, CIS) C301 1-126-160-11 ELECT 1uF 20% 50V
* A-4407-153-A MAIN BOARD, COMPLETE (EA, MY, SP) C302 1-130-479-00 MYLAR 0.0047uF 5% 50V
* A-4407-154-A MAIN BOARD, COMPLETE (E) C303 1-136-165-00 FILM 0.1uF 5% 50V
******************** C304 1-136-165-00 FILM 0.1uF 5% 50V
C305 1-126-964-11 ELECT 10uF 20% 50V
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
C306 1-126-160-11 ELECT 1uF 20% 50V
< CAPACITOR > C307 1-126-959-11 ELECT 0.47uF 20% 50V
C308 1-126-964-11 ELECT 10uF 20% 50V
C101 1-162-286-31 CERAMIC 220PF 10% 50V C309 1-136-173-00 FILM 0.47uF 5% 50V
C102 1-162-286-31 CERAMIC 220PF 10% 50V C310 1-162-290-31 CERAMIC 470PF 10% 50V
C103 1-164-159-11 CERAMIC 0.1uF 50V
C111 1-137-195-11 FILM 0.56uF 5% 50V C311 1-126-964-11 ELECT 10uF 20% 50V
C112 1-136-158-00 FILM 0.027uF 5% 50V C312 1-126-959-11 ELECT 0.47uF 20% 50V
C313 1-162-294-31 CERAMIC 0.001uF 10% 50V
C114 1-130-480-00 MYLAR 0.0056uF 5% 50V C315 1-126-963-11 ELECT 4.7uF 20% 50V
C115 1-136-159-00 FILM 0.033uF 5% 50V
C116 1-130-473-00 MYLAR 0.0015uF 5% 50V C316 1-104-665-11 ELECT 100uF 20% 10V
C320 1-162-290-31 CERAMIC 470PF 10% 50V
C118 1-130-467-00 MYLAR 470PF 5% 50V C331 1-164-159-11 CERAMIC 0.1uF 50V
C119 1-130-479-00 MYLAR 0.0047uF 5% 50V C332 1-164-159-11 CERAMIC 0.1uF 50V
C120 1-136-153-00 FILM 0.01uF 5% 50V
C121 1-126-964-11 ELECT 10uF 20% 50V C333 1-162-600-11 CERAMIC 0.0047uF 20% 16V
C122 1-162-291-31 CERAMIC 560PF 10% 50V C334 1-162-600-11 CERAMIC 0.0047uF 20% 16V
C351 1-126-160-11 ELECT 1uF 20% 50V
C123 1-136-165-00 FILM 0.1uF 5% 50V C352 1-130-479-00 MYLAR 0.0047uF 5% 50V
C124 1-136-165-00 FILM 0.1uF 5% 50V C353 1-136-165-00 FILM 0.1uF 5% 50V
C125 1-126-964-11 ELECT 10uF 20% 50V
C131 1-104-664-11 ELECT 47uF 20% 16V C354 1-136-165-00 FILM 0.1uF 5% 50V
C132 1-104-664-11 ELECT 47uF 20% 16V C355 1-126-964-11 ELECT 10uF 20% 50V
C356 1-126-160-11 ELECT 1uF 20% 50V
– 100 –
MAIN
C357 1-126-959-11 ELECT 0.47uF 20% 50V C916 1-164-159-11 CERAMIC 0.1uF 50V
C358 1-126-964-11 ELECT 10uF 20% 50V
C917 1-126-933-11 ELECT 100uF 20% 16V
C381 1-162-306-11 CERAMIC 0.01uF 20% 16V C919 1-126-968-11 ELECT 100uF 20% 50V
C391 1-164-159-11 CERAMIC 0.1uF 50V C921 1-126-947-11 ELECT 47uF 20% 35V
C392 1-126-916-11 ELECT 1000uF 20% 6.3V
C951 1-136-165-00 FILM 0.1uF 5% 50V
C393 1-164-159-11 CERAMIC 0.1uF 50V C952 1-126-943-11 ELECT 2200uF 20% 25V
C395 1-162-290-31 CERAMIC 470PF 10% 50V C955 1-104-661-00 ELECT 330uF 20% 16V
C396 1-126-961-11 ELECT 2.2uF 20% 50V
C397 1-126-961-11 ELECT 2.2uF 20% 50V < CONNECTOR >
C405 1-136-495-11 FILM 0.068uF 5% 50V CN101 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P
(EE, CIS) * CN102 1-568-832-11 SOCKET, CONNECTOR 13P (E)
C406 1-136-495-11 FILM 0.068uF 5% 50V CN102 1-568-834-11 SOCKET, CONNECTOR 15P (EXCEPT E)
(EE, CIS) * CN103 1-568-946-11 PIN, CONNECTOR 8P
C407 1-136-495-11 FILM 0.068uF 5% 50V * CN104 1-568-947-11 PIN, CONNECTOR 9P
(EE, CIS)
C408 1-136-495-11 FILM 0.068uF 5% 50V * CN105 1-568-862-11 SOCKET, CONNECTOR 19P
(EE, CIS) CN106 1-568-834-11 SOCKET, CONNECTOR 15P
C409 1-164-159-11 CERAMIC 0.1uF 50V * CN107 1-568-836-11 SOCKET, CONNECTOR 17P
CN110 1-564-506-11 PLUG, CONNECTOR 3P
C410 1-126-963-11 ELECT 4.7uF 20% 50V * CN201 1-568-832-11 SOCKET, CONNECTOR 13P
C411 1-164-159-11 CERAMIC 0.1uF 50V
C431 1-126-934-11 ELECT 220uF 20% 10V * CN301 1-568-449-11 HOUSING, CONNECTOR(PC BOARD)3P
C432 1-104-665-11 ELECT 100uF 20% 10V
C433 1-126-961-11 ELECT 2.2uF 20% 50V < DIODE >
C434 1-126-966-11 ELECT 33uF 20% 50V D141 8-719-911-19 DIODE 1SS119
C455 1-136-495-11 FILM 0.068uF 5% 50V D333 8-719-911-19 DIODE 1SS119
(EE, CIS) D334 8-719-911-19 DIODE 1SS119
(EE, CIS) D402 8-719-911-19 DIODE 1SS119
C457 1-136-495-11 FILM 0.068uF 5% 50V
(EE, CIS) D403 8-719-911-19 DIODE 1SS119
(EE, CIS) D405 8-719-024-99 DIODE 11ES2-NTA2B
D406 8-719-024-99 DIODE 11ES2-NTA2B
C501 1-104-664-11 ELECT 47uF 20% 10V D407 8-719-024-99 DIODE 11ES2-NTA2B
C502 1-164-159-11 CERAMIC 0.1uF 50V
C504 1-126-916-11 ELECT 1000uF 20% 6.3V D409 8-719-911-19 DIODE 1SS119
C505 1-162-306-11 CERAMIC 0.01uF 20% 16V D501 8-719-024-99 DIODE 11ES2-NTA2B
D502 8-719-024-99 DIODE 11ES2-NTA2B
C507 1-164-159-11 CERAMIC 0.1uF 50V
C509 1-102-958-00 CERAMIC 20PF 5% 50V D505 8-719-911-19 DIODE 1SS119
C510 1-102-514-11 CERAMIC 22PF 5% 50V D506 8-719-911-19 DIODE 1SS119
D507 8-719-024-99 DIODE 11ES2-NTA2B
C512 1-162-294-31 CERAMIC 0.001uF 10% 50V D508 8-719-911-19 DIODE 1SS119
C571 1-109-889-11 ELECT 1uF 20% 50V
C901 1-136-165-00 FILM 0.1uF 5% 50V D901 8-719-024-99 DIODE 11ES2-NTA2B
D904 8-719-024-99 DIODE 11ES2-NTA2B
C904 1-104-664-11 ELECT 47uF 20% 16V D905 8-719-933-36 DIODE HZS6B1L
C905 1-104-661-00 ELECT 330uF 20% 16V
D909 8-719-024-99 DIODE 11ES2-NTA2B
C913 1-126-943-11 ELECT 2200uF 20% 25V
C914 1-126-767-11 ELECT 1000uF 20% 16V D911 8-719-934-25 DIODE HZS33-1L
C915 1-104-664-11 ELECT 47uF 20% 16V D912 8-719-921-48 DIODE MTZJ-T-72-5.6C
– 101 –
MAIN
D913 8-719-911-19 DIODE 1SS119 Q434 8-729-620-05 TRANSISTOR 2SC2603-EF
D914 8-719-024-99 DIODE 11ES2-NTA2B Q435 8-729-029-86 TRANSISTOR DTC124ESA
D915 8-719-935-69 DIODE HZS11B1LTA Q436 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q437 8-729-029-86 TRANSISTOR DTC124ESA
< GROUND PLATE > Q501 8-729-620-05 TRANSISTOR 2SC2603-EF
* EPT1 4-870-539-11 PLATE, GROUND Q571 8-729-029-40 TRANSISTOR DTA124ESA

Q572 8-729-029-40 TRANSISTOR DTA124ESA
< IC > Q575 8-729-029-86 TRANSISTOR DTC124ESA
Q901 8-729-209-15 TRANSISTOR 2SD2012
IC101 8-759-495-24 IC M62442FP-TP Q902 8-729-620-05 TRANSISTOR 2SC2603-EF
IC102 8-759-634-51 IC M5218AP
IC191 8-759-634-50 IC M5218AL Q903 8-729-029-68 TRANSISTOR DTC114TSA
IC301 8-759-495-26 IC HA12215 Q905 8-729-040-20 TRANSISTOR RT1P137L-TP
IC381 8-749-923-04 IC TOTX178 (CD DIGITAL OUT, OPTICAL) Q906 8-729-029-40 TRANSISTOR DTA124ESA
Q907 8-729-040-20 TRANSISTOR RT1P137L-TP
IC501 8-759-537-36 IC uPD780018AYGF-012-3BA Q908 8-729-029-86 TRANSISTOR DTC124ESA
IC502 8-759-635-63 IC M51943BSL
IC901 8-759-604-86 IC M5F7807L Q909 8-729-026-68 TRANSISTOR 2SD2525(TP)
IC902 8-759-231-53 IC TA7805S Q910 8-729-030-19 TRANSISTOR 2SB1640
IC903 8-759-231-58 IC TA7812S Q913 8-729-620-05 TRANSISTOR 2SC2603-EF
Q914 8-729-119-76 TRANSISTOR 2SA1175-HFE
< JACK > Q951 8-729-141-83 TRANSISTOR 2SB1094-LK
J101 1-695-188-31 JACK, PIN 4P (MD/VIDEO (AUDIO), IN/OUT) Q952 8-729-119-76 TRANSISTOR 2SA1175-HFE
J191 1-774-785-11 JACK, PIN 1P (SUPER WOOFER)
< RESISTOR >
< COIL >
R101 1-249-417-11 CARBON 1K 5% 1/4W
L381 1-410-521-11 INDUCTOR 100uH R102 1-249-417-11 CARBON 1K 5% 1/4W
L392 1-410-521-11 INDUCTOR 100uH R111 1-247-826-00 CARBON 620 5% 1/4W
L401 1-420-872-00 COIL, AIR-CORE (EE, CIS) R112 1-247-903-00 CARBON 1M 5% 1/4W
L402 1-420-872-00 COIL, AIR-CORE (EE, CIS) R113 1-247-903-00 CARBON 1M 5% 1/4W
L451 1-420-872-00 COIL, AIR-CORE (EE, CIS)
R114 1-249-419-11 CARBON 1.5K 5% 1/4W
L452 1-420-872-00 COIL, AIR-CORE (EE, CIS) R115 1-249-433-11 CARBON 22K 5% 1/4W
L501 1-410-509-11 INDUCTOR 10uH R116 1-247-887-00 CARBON 220K 5% 1/4W
R117 1-249-429-11 CARBON 10K 5% 1/4W
< TRANSISTOR > R118 1-249-437-11 CARBON 47K 5% 1/4W
Q111 8-729-620-05 TRANSISTOR 2SC2603-EF R119 1-249-421-11 CARBON 2.2K 5% 1/4W

Q112 8-729-620-05 TRANSISTOR 2SC2603-EF R120 1-249-441-11 CARBON 100K 5% 1/4W
Q113 8-729-141-30 TRANSISTOR 2SC3623A-LK R121 1-249-429-11 CARBON 10K 5% 1/4W
Q163 8-729-141-30 TRANSISTOR 2SC3623A-LK R125 1-247-843-11 CARBON 3.3K 5% 1/4W

Q191 8-729-141-30 TRANSISTOR 2SC3623A-LK R126 1-249-437-11 CARBON 47K 5% 1/4W
Q331 8-729-116-59 TRANSISTOR 2SB1068TP R127 1-249-437-11 CARBON 47K 5% 1/4W
Q332 8-729-029-66 TRANSISTOR DTC114ESA R128 1-249-421-11 CARBON 2.2K 5% 1/4W
Q333 8-729-116-59 TRANSISTOR 2SB1068TP R131 1-247-807-31 CARBON 100 5% 1/4W
Q334 8-729-029-66 TRANSISTOR DTC114ESA R132 1-247-807-31 CARBON 100 5% 1/4W

Q336 8-729-116-59 TRANSISTOR 2SB1068TP R141 1-249-433-11 CARBON 22K 5% 1/4W
Q337 8-729-045-21 TRANSISTOR 2SD1513TP-LK R142 1-249-433-11 CARBON 22K 5% 1/4W
Q338 8-729-029-21 TRANSISTOR DTA114ESA-TP R143 1-249-417-11 CARBON 1K 5% 1/4W
Q339 8-729-029-66 TRANSISTOR DTC114ESA R144 1-249-441-11 CARBON 100K 5% 1/4W

Q340 8-729-116-59 TRANSISTOR 2SB1068TP R145 1-247-903-00 CARBON 1M 5% 1/4W
Q341 8-729-045-21 TRANSISTOR 2SD1513TP-LK R151 1-249-417-11 CARBON 1K 5% 1/4W
Q342 8-729-029-21 TRANSISTOR DTA114ESA-TP R152 1-249-417-11 CARBON 1K 5% 1/4W
Q401 8-729-119-76 TRANSISTOR 2SA1175-HFE R162 1-247-903-00 CARBON 1M 5% 1/4W

Q402 8-729-111-29 TRANSISTOR 2SD1616A-K R163 1-247-903-00 CARBON 1M 5% 1/4W
Q432 8-729-119-76 TRANSISTOR 2SA1175-HFE R165 1-249-433-11 CARBON 22K 5% 1/4W
– 102 –
MAIN
R168 1-249-437-11 CARBON 47K 5% 1/4W R355 1-249-421-11 CARBON 2.2K 5% 1/4W
R169 1-249-421-11 CARBON 2.2K 5% 1/4W
R358 1-249-425-11 CARBON 4.7K 5% 1/4W
R178 1-249-421-11 CARBON 2.2K 5% 1/4W R391 1-247-807-31 CARBON 100 5% 1/4W
R191 1-249-437-11 CARBON 47K 5% 1/4W
R394 1-249-435-11 CARBON 33K 5% 1/4W
R195 1-249-429-11 CARBON 10K 5% 1/4W (EE, CIS)
R197 1-249-441-11 CARBON 100K 5% 1/4W (EE, CIS)
R198 1-249-417-11 CARBON 1K 5% 1/4W
R404 1-260-076-11 CARBON 10 5% 1/2W
R199 1-249-429-11 CARBON 10K 5% 1/4W (EE, CIS)
R302 1-249-421-11 CARBON 2.2K 5% 1/4W (EE, CIS)
R408 1-249-425-11 CARBON 4.7K 5% 1/4W
R305 1-249-421-11 CARBON 2.2K 5% 1/4W
R308 1-249-425-11 CARBON 4.7K 5% 1/4W ! R411 1-216-456-00 METAL OXIDE 820 5% 2W F
R309 1-249-433-11 CARBON 22K 5% 1/4W ! R412 1-216-456-00 METAL OXIDE 820 5% 2W F
R413 1-249-437-11 CARBON 47K 5% 1/4W
R311 1-247-903-00 CARBON 1M 5% 1/4W
R432 1-249-437-11 CARBON 47K 5% 1/4W
R317 1-249-429-11 CARBON 10K 5% 1/4W
R438 1-249-429-11 CARBON 10K 5% 1/4W
R324 1-247-876-11 CARBON 75K 5% 1/4W
R451 1-260-076-11 CARBON 10 5% 1/2W
R329 1-249-417-11 CARBON 1K 5% 1/4W (EE, CIS)
R330 1-249-425-11 CARBON 4.7K 5% 1/4W
R332 1-249-415-11 CARBON 680 5% 1/4W (EE, CIS)
(EE, CIS)
R334 1-249-415-11 CARBON 680 5% 1/4W R455 1-260-076-11 CARBON 10 5% 1/2W
R335 1-249-421-11 CARBON 2.2K 5% 1/4W (EE, CIS)
R338 1-249-411-11 CARBON 330 5% 1/4W
R501 1-249-413-11 CARBON 470 5% 1/4W
R343 1-249-417-11 CARBON 1K 5% 1/4W
R507 1-247-897-11 CARBON 560K 5% 1/4W
R353 1-247-807-31 CARBON 100 5% 1/4W (EE, CIS, E)

– 103 –
MAIN MOTOR (SLIDE) MOTOR (TURN)
R512 1-249-425-11 CARBON 4.7K 5% 1/4W(E) R909 1-249-430-11 CARBON 12K 5% 1/4W
(EE, CIS) R912 1-249-417-11 CARBON 1K 5% 1/4W
R521 1-247-807-31 CARBON 100 5% 1/4W
R915 1-249-409-11 CARBON 220 5% 1/4W
R527 1-247-807-31 CARBON 100 5% 1/4W R920 1-249-383-11 CARBON 1.5 5% 1/6W
R528 1-247-807-31 CARBON 100 5% 1/4W R921 1-249-383-11 CARBON 1.5 5% 1/6W
R529 1-247-807-31 CARBON 100 5% 1/4W
R530 1-247-807-31 CARBON 100 5% 1/4W < VARIABLE RESISTOR >
R531 1-247-807-31 CARBON 100 5% 1/4W
RV301 1-238-600-11 RES, ADJ, CARBON 10K
R532 1-247-807-31 CARBON 100 5% 1/4W RV351 1-238-600-11 RES, ADJ, CARBON 10K
R533 1-247-807-31 CARBON 100 5% 1/4W
R534 1-247-807-31 CARBON 100 5% 1/4W < RELAY >
R535 1-247-807-31 CARBON 100 5% 1/4W
R536 1-247-807-31 CARBON 100 5% 1/4W RY401 1-755-141-11 RELAY
RY402 1-755-141-11 RELAY
R537 1-247-807-31 CARBON 100 5% 1/4W
R538 1-247-807-31 CARBON 100 5% 1/4W < TERMINAL >
R539 1-247-807-31 CARBON 100 5% 1/4W
R540 1-247-807-31 CARBON 100 5% 1/4W TM401 1-537-240-31 TERMINAL BOARD (CHECKER PIN)
R541 1-247-807-31 CARBON 100 5% 1/4W (SPEAKER)
R542 1-247-807-31 CARBON 100 5% 1/4W < VIBRATOR >

R543 1-247-807-31 CARBON 100 5% 1/4W
R544 1-249-429-11 CARBON 10K 5% 1/4W X501 1-760-489-11 VIBRATOR, CERAMIC (5MHz)
R545 1-247-807-31 CARBON 100 5% 1/4W X502 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
R546 1-247-843-11 CARBON 3.3K 5% 1/4W ************************************************************
R547 1-247-807-31 CARBON 100 5% 1/4W * 1-658-578-11 MOTOR (SLIDE) BOARD

R548 1-247-807-31 CARBON 100 5% 1/4W *******************
R549 1-247-807-31 CARBON 100 5% 1/4W
R550 1-247-807-31 CARBON 100 5% 1/4W < CAPACITOR >
R551 1-247-807-31 CARBON 100 5% 1/4W
C801 1-162-306-11 CERAMIC 0.01uF 20% 16V
R552 1-247-807-31 CARBON 100 5% 1/4W C804 1-162-306-11 CERAMIC 0.01uF 20% 16V
R553 1-249-429-11 CARBON 10K 5% 1/4W C805 1-126-964-11 ELECT 10uF 20% 50V
R554 1-247-807-31 CARBON 100 5% 1/4W
R555 1-249-429-11 CARBON 10K 5% 1/4W < CONNECTOR >
R556 1-247-807-31 CARBON 100 5% 1/4W
* CN801 1-568-947-11 PIN, CONNECTOR 9P
R557 1-249-429-11 CARBON 10K 5% 1/4W
R558 1-247-807-31 CARBON 100 5% 1/4W < DIODE >
R559 1-249-429-11 CARBON 10K 5% 1/4W
R561 1-247-807-31 CARBON 100 5% 1/4W D801 8-719-921-48 DIODE MTZJ-T-72-5.6C
D805 8-719-911-19 DIODE 1SS119
R563 1-247-807-31 CARBON 100 5% 1/4W
R564 1-247-807-31 CARBON 100 5% 1/4W < IC >
R565 1-247-807-31 CARBON 100 5% 1/4W
R566 1-247-807-31 CARBON 100 5% 1/4W IC801 8-759-274-09 IC BA6286N
R567 1-247-807-31 CARBON 100 5% 1/4W
< RESISTOR >
R571 1-249-421-11 CARBON 2.2K 5% 1/4W
R576 1-249-429-11 CARBON 10K 5% 1/4W
R577 1-249-417-11 CARBON 1K 5% 1/4W < SWITCH >
R901 1-247-843-11 CARBON 3.3K 5% 1/4W
S801 1-762-527-11 SWITCH, ROTARY (OPEN/CLOSE DET)
R902 1-249-415-11 CARBON 680 5% 1/4W ************************************************************
R903 1-249-419-11 CARBON 1.5K 5% 1/4W
R904 1-249-414-11 CARBON 560 5% 1/4W * 1-658-577-11 MOTOR (TURN) BOARD
R905 1-249-425-11 CARBON 4.7K 5% 1/4W ******************
R906 1-247-843-11 CARBON 3.3K 5% 1/4W
< CAPACITOR >
R907 1-249-415-11 CARBON 680 5% 1/4W
R908 1-249-429-11 CARBON 10K 5% 1/4W C701 1-162-306-11 CERAMIC 0.01uF 20% 16V
– 104 –
MOTOR (TURN) PANEL
C702 1-126-964-11 ELECT 10uF 20% 50V C635 1-126-163-11 ELECT 4.7uF 20% 50V
C705 1-162-306-11 CERAMIC 0.01uF 20% 16V C636 1-162-294-31 CERAMIC 0.001uF 10% 50V
C648 1-162-306-11 CERAMIC 0.01uF 20% 16V
< CONNECTOR > C649 1-124-589-11 ELECT 47uF 20% 16V
CN703 1-750-413-11 CONNECTOR, FFC/FPC 8P C749 1-164-159-11 CERAMIC 0.1uF 50V

CN704 1-506-469-11 PIN, CONNECTOR 4P C752 1-164-159-11 CERAMIC 0.1uF 50V
C753 1-162-290-31 CERAMIC 470PF 10% 50V
< DIODE > C754 1-162-306-11 CERAMIC 0.01uF 20% 16V
C755 1-126-961-11 ELECT 2.2uF 20% 50V
D701 8-719-983-66 DIODE MTZJ-T-72-3.6B
C756 1-162-294-31 CERAMIC 0.001uF 10% 50V
< IC > C757 1-162-215-31 CERAMIC 47PF 5% 50V
C758 1-126-964-11 ELECT 10uF 20% 50V
IC701 8-759-633-65 IC M54641L C759 1-126-956-00 ELECT 0.1uF 20% 50V
C760 1-162-215-31 CERAMIC 47PF 5% 50V
< RESISTOR >
C761 1-162-282-31 CERAMIC 100PF 10% 50V
R706 1-249-411-11 CARBON 330 5% 1/4W C762 1-126-961-11 ELECT 2.2uF 20% 50V
R707 1-249-401-11 CARBON 47 5% 1/4W C764 1-126-964-11 ELECT 10uF 20% 50V
************************************************************
< CONNECTOR >
* A-4407-170-A PANEL BOARD, COMPLETE (EE, CIS)
* A-4407-171-A PANEL BOARD, COMPLETE (EA) * CN601 1-568-856-11 SOCKET, CONNECTOR 13P
* A-4407-172-A PANEL BOARD, COMPLETE (E, MY, SP)
********************* < DIODE >
* 4-949-935-21 CUSHION (FL) D602 8-719-986-73 DIODE RB441Q

* 4-996-724-01 HOLDER, FL TUBE D610 8-719-063-93 LED SLR325VC-N-T32 (ENTER/NEXT)
D612 8-719-057-97 LED SEL5923A-TP15 (GROOVE)
< CAPACITOR > D613 8-719-063-93 LED SLR325VC-N-T32 (JOG)
D614 8-719-064-65 LED SELU5723C-TP15 (DJ MIX)
C601 1-164-159-11 CERAMIC 0.1uF 50V
C602 1-162-306-11 CERAMIC 0.01uF 20% 16V D615 8-719-064-65 LED SELU5723C-TP15 (DJ MIX)
C603 1-124-589-11 ELECT 47uF 20% 16V D616 8-719-063-93 LED SLR325VC-N-T32 (NON-STOP)
C604 1-126-163-11 ELECT 4.7uF 20% 50V D617 8-719-057-97 LED SEL5923A-TP15 (+, ))
C605 1-162-294-31 CERAMIC 0.001uF 10% 50V D618 8-719-057-97 LED SEL5923A-TP15 (–, 0)
D620 8-719-063-93 LED SLR325VC-N-T32 (EFFECT)
C606 1-126-160-11 ELECT 1uF 20% 50V
C607 1-126-160-11 ELECT 1uF 20% 50V D621 8-719-056-13 LED SML79423C-TP15 (CD, ^)
C608 1-162-294-31 CERAMIC 0.001uF 10% 50V D622 8-719-058-03 LED SEL5423E-TP15 (TAPE B, ()
C609 1-162-282-31 CERAMIC 100PF 10% 50V D623 8-719-058-03 LED SEL5423E-TP15 (TAPE B, 9)
C610 1-162-282-31 CERAMIC 100PF 10% 50V D624 8-719-058-03 LED SEL5423E-TP15 (TAPE A, ()
D625 8-719-058-03 LED SEL5423E-TP15 (TAPE A, 9)
C611 1-162-282-31 CERAMIC 100PF 10% 50V
C612 1-162-282-31 CERAMIC 100PF 10% 50V D651 8-719-063-93 LED SLR325VC-N-T32 (r REC)
C613 1-162-282-31 CERAMIC 100PF 10% 50V D652 8-719-057-97 LED SEL5923A-TP15 (P PAUSE)
C614 1-162-282-31 CERAMIC 100PF 10% 50V
C615 1-162-282-31 CERAMIC 100PF 10% 50V < LEAD >
C616 1-162-282-31 CERAMIC 100PF 10% 50V EL2 1-690-880-51 LEAD (WITH CONNECTOR)
C617 1-162-282-31 CERAMIC 100PF 10% 50V
C618 1-162-282-31 CERAMIC 100PF 10% 50V < FERRITE BEAD >
C619 1-162-282-31 CERAMIC 100PF 10% 50V
C620 1-162-282-31 CERAMIC 100PF 10% 50V FB601 1-410-397-21 FERRITE BEAD INDUCTOR
C621 1-162-282-31 CERAMIC 100PF 10% 50V < FLUORESCENT INDICATOR TUBE >
C625 1-162-294-31 CERAMIC 0.001uF 10% 50V
C626 1-124-589-11 ELECT 47uF 20% 16V FL601 1-517-731-11 INDICATOR TUBE, FLUORESCENT
C627 1-162-306-11 CERAMIC 0.01uF 20% 16V
C628 1-162-306-11 CERAMIC 0.01uF 20% 16V < IC >
C629 1-162-306-11 CERAMIC 0.01uF 20% 16V IC601 8-759-496-12 IC TMP87CM74AF-6671

C630 1-162-306-11 CERAMIC 0.01uF 20% 16V IC602 8-749-011-05 IC GP1U28X
C631 1-126-157-11 ELECT 10uF 20% 16V IC603 8-759-495-25 IC BA3833F-E2
C632 1-126-157-11 ELECT 10uF 20% 16V IC750 8-759-634-51 IC M5218AP
C633 1-162-303-11 CERAMIC 0.0033uF 30% 16V
C634 1-126-157-11 ELECT 10uF 20% 16V
– 105 –
PANEL
< JACK > R640 1-249-416-11 CARBON 820 5% 1/4W
R641 1-249-418-11 CARBON 1.2K 5% 1/4W
J751 1-784-224-11 JACK (LARGE TYPE) (MIX MIC) R642 1-249-419-11 CARBON 1.5K 5% 1/4W
R643 1-249-421-11 CARBON 2.2K 5% 1/4W
< COIL >
R649 1-249-430-11 CARBON 12K 5% 1/4W
L601 1-410-509-11 INDUCTOR 10uH R650 1-249-412-11 CARBON 390 5% 1/4W
R651 1-249-413-11 CARBON 470 5% 1/4W
< TRANSISTOR > R652 1-249-415-11 CARBON 680 5% 1/4W
R653 1-249-416-11 CARBON 820 5% 1/4W
Q601 8-729-118-00 TRANSISTOR 2SB1116-L
Q602 8-729-118-00 TRANSISTOR 2SB1116-L R654 1-249-418-11 CARBON 1.2K 5% 1/4W
Q604 8-729-029-68 TRANSISTOR DTC114TSA R661 1-249-429-11 CARBON 10K 5% 1/4W
Q607 8-729-029-68 TRANSISTOR DTC114TSA R662 1-249-421-11 CARBON 2.2K 5% 1/4W
R663 1-249-421-11 CARBON 2.2K 5% 1/4W
Q609 8-729-029-68 TRANSISTOR DTC114TSA R664 1-249-409-11 CARBON 220 5% 1/4W
Q610 8-729-029-68 TRANSISTOR DTC114TSA R665 1-249-429-11 CARBON 10K 5% 1/4W
R668 1-249-407-11 CARBON 150 5% 1/4W
R669 1-247-804-11 CARBON 75 5% 1/4W
< RESISTOR > R670 1-249-407-11 CARBON 150 5% 1/4W
R671 1-249-407-11 CARBON 150 5% 1/4W
R601 1-247-903-00 CARBON 1M 5% 1/4W R672 1-249-407-11 CARBON 150 5% 1/4W
R604 1-249-429-11 CARBON 10K 5% 1/4W
R676 1-247-804-11 CARBON 75 5% 1/4W
R609 1-247-843-11 CARBON 3.3K 5% 1/4W
R684 1-249-441-11 CARBON 100K 5% 1/4W
R614 1-249-433-11 CARBON 22K 5% 1/4W
R728 1-249-415-11 CARBON 680 5% 1/4W
R620 1-247-895-00 CARBON 470K 5% 1/4W
R622 1-249-412-11 CARBON 390 5% 1/4W R732 1-249-421-11 CARBON 2.2K 5% 1/4W
R733 1-249-422-11 CARBON 2.7K 5% 1/4W
R625 1-249-416-11 CARBON 820 5% 1/4W
R752 1-249-441-11 CARBON 100K 5% 1/4W
R630 1-249-424-11 CARBON 3.9K 5% 1/4W
R757 1-247-807-31 CARBON 100 5% 1/4W
R633 1-249-430-11 CARBON 12K 5% 1/4W
R634 1-249-432-11 CARBON 18K 5% 1/4W < VARIABLE RESISTOR >
R636 1-249-430-11 CARBON 12K 5% 1/4W
R637 1-249-412-11 CARBON 390 5% 1/4W RV750 1-225-574-11 RES, VAR, CARBON 50K (MIC LEVEL)
R638 1-249-413-11 CARBON 470 5% 1/4W
R639 1-249-415-11 CARBON 680 5% 1/4W
– 106 –
PANEL SENSOR TCB
< SWITCH > A-4303-587-A TCB BOARD, COMPLETE (EE, CIS)
********************
S601 1-473-534-11 ENCODER, ROTARY
(=˜+, DJ MIX (JOG)) < CAPACITOR >
S602 1-473-392-11 ENCODER, ROTARY (VOLUME)
S604 1-762-875-21 SWITCH, KEYBOARD (EFFECT) C1 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
S605 1-762-875-21 SWITCH, KEYBOARD (SURROUND) C2 1-104-664-11 ELECT 47uF 20% 16V
S606 1-762-875-21 SWITCH, KEYBOARD (KARAOKE PON/MPX) C3 1-163-038-00 CERAMIC CHIP 0.1uF 25V
S607 1-762-875-21 SWITCH, KEYBOARD (p) C6 1-163-038-00 CERAMIC CHIP 0.1uF 25V
S608 1-762-875-21 SWITCH, KEYBOARD (TIMER SELECT)
S609 1-762-875-21 SWITCH, KEYBOARD (CLOCK/TIMER SET) C7 1-101-004-00 CERAMIC 0.01uF 50V
S610 1-762-875-21 SWITCH, KEYBOARD (DISPLAY/DEMO) C8 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S611 1-762-875-21 SWITCH, KEYBOARD (FILE SELECT) C9 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S612 1-762-875-21 SWITCH, KEYBOARD (GEQ CONTROL) C16 1-163-038-00 CERAMIC CHIP 0.1uF 25V
S613 1-762-875-21 SWITCH, KEYBOARD (P FILE MEMORY)
S614 1-762-875-21 SWITCH, KEYBOARD (FUNCTION) C19 1-163-249-11 CERAMIC CHIP 82PF 5% 50V
S615 1-762-875-21 SWITCH, KEYBOARD (EDIT, DIRECTION) C21 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
S616 1-762-875-21 SWITCH, KEYBOARD (PLAY MODE, DOLBY NR) C22 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S617 1-762-875-21 SWITCH, KEYBOARD (REPEAT) C24 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
S618 1-762-875-21 SWITCH, KEYBOARD (LOOP)
S619 1-762-875-21 SWITCH, KEYBOARD (FLASH) C26 1-104-664-11 ELECT 47uF 20% 16V
S620 1-762-875-21 SWITCH, KEYBOARD (NON-STOP) C28 1-104-664-11 ELECT 47uF 20% 16V
S621 1-762-875-21 SWITCH, KEYBOARD (–, 0) C29 1-162-306-11 CERAMIC 0.01uF 30% 16V
C30 1-126-961-11 ELECT 2.2uF 20% 50V
S622 1-762-875-21 SWITCH, KEYBOARD (ENTER/NEXT) C31 1-163-031-11 CERAMIC CHIP 0.01uF 50V
S623 1-762-875-21 SWITCH, KEYBOARD (+, ))
S624 1-762-875-21 SWITCH, KEYBOARD (DBFB) C32 1-163-038-00 CERAMIC CHIP 0.1uF 25V
S625 1-762-875-21 SWITCH, KEYBOARD (GROOVE) C33 1-163-038-00 CERAMIC CHIP 0.1uF 25V
S631 1-762-875-21 SWITCH, KEYBOARD (TUNER, BAND) C34 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
S632 1-762-875-21 SWITCH, KEYBOARD (CD, ^) C36 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
S633 1-762-875-21 SWITCH, KEYBOARD (TAPE B, ()
S634 1-762-875-21 SWITCH, KEYBOARD (TAPE B, 9) C37 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
S635 1-762-875-21 SWITCH, KEYBOARD (TAPE A, () C39 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
S636 1-762-875-21 SWITCH, KEYBOARD (TAPE A, 9) C40 1-104-664-11 ELECT 47uF 20% 16V
S656 1-762-875-21 SWITCH, KEYBOARD (r REC) C42 1-163-038-00 CERAMIC CHIP 0.1uF 25V
S657 1-762-875-21 SWITCH, KEYBOARD (P PAUSE)
S658 1-762-875-21 SWITCH, KEYBOARD (HI-DUB) C43 1-163-031-00 CERAMIC CHIP 0.01uF 50V
S659 1-762-875-21 SWITCH, KEYBOARD (CD SYNC) C44 1-163-038-00 CERAMIC CHIP 0.1uF 25V
< VIBRATOR > C46 1-104-664-11 ELECT 47uF 20% 16V
C47 1-126-301-11 ELECT 1.0uF 20% 50V
X601 1-579-952-21 VIBRATOR, CERAMIC (8MHz)
************************************************************ C48 1-163-059-00 CERAMIC CHIP 0.01uF 50V
C49 1-126-964-11 ELECT 10uF 20% 50V
* 1-658-576-11 SENSOR BOARD C50 1-126-960-11 ELECT 1.0uF 20% 50V
************* C51 1-126-959-11 ELECT 0.47uF 20% 50V
C52 1-126-960-11 ELECT 1.0uF 20% 50V
<PHOTO INTERRUPTER/REFLECTOR >
C53 1-126-964-11 ELECT 10uF 20% 50V
IC702 8-749-924-18 PHOTO INTERRUPTER RPI-1391 C54 1-104-396-11 ELECT 10uF 20% 16V
IC703 8-749-924-30 PHOTO REFLECTOR GP2S28 C55 1-104-396-11 ELECT 10uF 20% 16V
C56 1-104-396-11 ELECT 10uF 20% 16V
< TRANSISTOR > C57 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
Q701 8-729-900-80 TRANSISTOR DTC114ES C58 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
< RESISTOR > C60 1-163-989-11 CERAMIC CHIP 33000PF 10% 25V
C61 1-126-301-11 ELECT 1.0uF 20% 50V
R701 1-249-416-11 CARBON 820 5% 1/4W C62 1-163-033-00 CERAMIC CHIP 0.022uF 50V
R702 1-249-407-11 CARBON 150 5% 1/4W
************************************************************ C63 1-163-139-00 CERAMIC CHIP 820PF 5% 50V
C65 1-104-664-11 ELECT 47uF 20% 16V
C67 1-126-162-11 ELECT 3.3uF 20% 50V
– 107 –
TCB
C68 1-163-031-11 CERAMIC 0.01uF 50V IC1701 8-759-063-04 IC IR3R42
C69 1-104-664-11 ELECT 47uF 20% 16V IC1702 8-759-140-53 IC uPD4053BC
C71 1-162-306-11 CERAMIC 0.01uF 30% 16V
C72 1-104-664-11 ELECT 47uF 20% 16V < IFT >
IFT41 1-431-974-11 TRANSFORMER, IF (CERAMIC FILTER)
C1701 1-162-294-31 CERAMIC CHIP 1000PF 10% 50V < SHORT >
C1702 1-130-014-00 FILM 470PF 5% 50V
C1703 1-126-959-11 ELECT 0.47uF 20% 50V JR2 1-216-295-OO SHORT 0
JR8 1-216-295-OO SHORT 0
C1705 1-163-035-00 CERAMIC CHIP 0.047uF 50V JR9 1-216-295-OO SHORT 0
C1710 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V JR46 1-216-296-00 SHORT 0
C1711 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V JR47 1-216-295-00 SHORT 0
JR48 1-216-295-00 SHORT 0
C1712 1-130-736-11 FILM 0.01uF 5% 50V JR49 1-216-296-00 SHORT 0
C1713 1-130-736-11 FILM 0.01uF 5% 50V JR51 1-216-295-00 SHORT 0
C1714 1-126-960-11 ELECT 1.0uF 20% 50V
C1715 1-126-960-11 ELECT 1.0uF 20% 50V JR52 1-216-295-00 SHORT 0
C1716 1-126-960-11 ELECT 1.0uF 20% 50V JR53 1-216-296-00 SHORT 0
JR54 1-216-295-00 SHORT 0
C1719 1-104-664-11 ELECT 47uF 20% 16V JR1701 1-216-295-00 SHORT 0
C1720 1-163-031-11 CERAMIC CHIP 0.01uF 50V JR1702 1-216-295-00 SHORT 0
C1724 1-163-031-11 CERAMIC CHIP 0.01uF 50V JR1703 1-216-295-00 SHORT 0
C1725 1-104-664-11 ELECT 47uF 20% 16V JR1704 1-216-295-00 SHORT 0
JR1705 1-216-295-00 SHORT 0
C1726 1-126-960-11 ELECT 1.0uF 20% 50V
C1727 1-126-960-11 ELECT 1.0uF 20% 50V < COIL >
C1728 1-126-966-11 ELECT 33uF 20% 16V
L3 1-410-521-11 MICRO INDUCTOR 100uH
< CERAMIC FILTER > L41 1-407-500-00 MICRO INDUCTOR 4.7mH
L1701 1-409-497-11 COIL (FILTER)
CF1 1-567-389-11 FILTER, CERAMIC
CF3 1-567-389-11 FILTER, CERAMIC < LOW-PASS FILTER >
< CONNECTOR > LPF41 1-239-845-11 FILTER, LOW PASS

LPF42 1-239-845-11 FILTER, LOW PASS
* CN1 1-568-834-11 SOCKET, CONNECTOR 15P
< TRANSISTOR >
< TRIMMER >
Q1 8-729-201-27 TRANSISTOR 2SC2715Y
CT1701 1-141-444-11 CAP, CERAMIC TRIMMER 50PF Q2 8-729-201-27 TRANSISTOR 2SC2715Y
CT1701 1-141-569-11 CAP, ADJ 50PF Q3 8-729-201-27 TRANSISTOR 2SC2715Y
Q4 8-729-201-27 TRANSISTOR 2SC2715Y
< DIODE > Q5 8-729-424-08 TRANSISTOR MUN2111
D21 8-719-976-99 DIODE DTZ5.1B Q9 8-729-216-22 TRANSISTOR 2SA812-M5M6

D41 8-719-016-74 DIODE 1SS352 Q11 8-729-421-22 TRANSISTOR MUN2211

D1703 8-719-991-19 DIODE 1SS133T Q1702 8-729-027-43 TRANSISTOR RT1N141C
< FRONT-END > < RESISTOR >
FE1 1-693-335-11 FRONT END (3 GANG) R1 1-249-401-11 CARBON 47 5% 1/4W

FE2 1-233-514-11 ENCAPSULATED COMPONENT R2 1-216-037-00 METAL CHIP 330 5% 1/10W
R3 1-216-037-00 METAL CHIP 330 5% 1/10W
< IC > R5 1-216-037-00 METAL CHIP 330 5% 1/10W
R6 1-216-081-00 METAL CHIP 22K 5% 1/10W
IC21 8-759-288-54 IC LC72130
IC41 8-759-495-82 IC LA1838 R7 1-216-049-11 METAL CHIP 1K 5% 1/10W
– 108 –
TCB TRANSFORMER
R8 1-216-037-00 METAL CHIP 330 5% 1/10W R1714 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R9 1-216-081-00 METAL CHIP 22K 5% 1/10W
R10 1-216-037-00 METAL CHIP 330 5% 1/10W R1715 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R11 1-216-081-00 METAL CHIP 22K 5% 1/10W R1716 1-216-097-00 METAL CHIP 100K 5% 1/10W
R1717 1-216-097-00 METAL CHIP 100K 5% 1/10W
R12 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R1718 1-249-429-11 CARBON 10K 5% 1/4W
R13 1-216-037-00 METAL CHIP 330 5% 1/10W R1719 1-216-097-00 METAL CHIP 100K 5% 1/10W
R14 1-216-081-00 METAL CHIP 22K 5% 1/10W
R18 1-216-073-00 METAL CHIP 10K 5% 1/10W R1720 1-249-434-11 CARBON 27K 5% 1/4W
R19 1-216-073-00 METAL CHIP 10K 5% 1/10W R1721 1-216-073-00 METAL CHIP 10K 5% 1/10W
R21 1-249-417-11 CARBON 1K 5% 1/4W < VARIABLE RESISTOR >

R22 1-249-417-11 CARBON 1K 5% 1/4W
R23 1-249-417-11 CARBON 1K 5% 1/4W RV41 1-238-600-11 RES, ADJ, CARBON 10K
R24 1-247-807-31 CARBON 100 5% 1/4W RV42 1-238-600-11 RES, ADJ, CARBON 10K
R25 1-249-417-11 CARBON 1K 5% 1/4W RV1701 1-238-601-11 RES, ADJ, CARBON 22K
R26 1-249-437-11 CARBON 47K 5% 1/4W
R27 1-249-429-11 CARBON 10K 5% 1/4W < TERMINAL >
R28 1-249-417-11 CARBON 1K 5% 1/4W
R29 1-216-061-00 METAL CHIP 3.3K 5% 1/10W TM1 1-537-488-11 TERMINAL BOARD (ANT) (ANTENNA)
R30 1-216-186-00 METAL CHIP 330 5% 1/8W
< TEST PIN>
R31 1-216-025-00 METAL CHIP 100 5% 1/10W
R32 1-249-425-11 CARBON 4.7K 5% 1/4W TP1701 1-536-354-00 PIN, POST
R33 1-249-425-11 CARBON 4.7K 5% 1/4W TP1702 1-536-354-00 PIN, POST
R34 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R35 1-216-214-00 METAL CHIP 4.7K 5% 1/8W < VIBRATOR >
R36 1-216-025-00 METAL CHIP 100 5% 1/10W X21 1-760-549-31 VIBRATOR, CRYSTAL (4.5MHz)
R37 1-216-073-00 METAL CHIP 10K 5% 1/10W X41 1-767-825-21 FILTER, CERAMIC (10.7MHz)
R38 1-216-089-00 METAL CHIP 47K 5% 1/10W X42 1-527-981-00 FILTER, CERAMIC (450kHz)
R39 1-249-429-11 CARBON 10K 5% 1/4W **************************************************************
R41 1-216-013-00 METAL CHIP 33 5% 1/10W
* 1-668-212-11 TRANSFORMER BOARD
R42 1-216-065-00 METAL CHIP 4.7K 5% 1/10W *******************
R43 1-216-037-00 METAL CHIP 330 5% 1/10W
R44 1-216-001-00 METAL CHIP 10 5% 1/10W 1-533-217-31 HOLDER, FUSE
R45 1-247-843-11 CARBON 3.3K 5% 1/4W 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
R46 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
< CONNECTOR >
R47 1-216-097-00 METAL CHIP 100K 5% 1/10W
R48 1-249-417-11 CARBON 1.0K 5% 1/4W CN11 1-564-523-11 PLUG, CONNECTOR 8P
R49 1-216-295-00 SHORT 0 * CN12 1-564-519-11 PLUG, CONNECTOR 4P
R50 1-216-065-00 METAL CHIP 4.7K 5% 1/10W CN13 1-564-321-00 PIN, CONNECTOR 2P
R51 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
< FUSE >
R52 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R53 1-216-061-00 METAL CHIP 3.3K 5% 1/4W ! F11 1-532-464-31 FUSE T2.5AL/250V
R54 1-216-073-00 METAL CHIP 10K 5% 1/10W ! F12 1-532-465-31 FUSE T3.15AL/250V (EXCEPT EE, CIS)
R55 1-216-061-00 METAL CHIP 3.3K 5% 1/10W ! F13 1-532-505-31 FUSE T5AL/250V (EXCEPT EE, CIS)
R57 1-216-162-00 METAL CHIP 33 5% 1/8W
< RESISTOR >
R58 1-216-013-00 METAL CHIP 33 5% 1/10W
R91 1-216-295-00 SHORT 0 ! R11 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R92 1-216-073-00 METAL CHIP 10K 5% 1/10W (EE, CIS)
R1701 1-216-079-00 METAL CHIP 18K 5% 1/10W ! R11 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
R1702 1-216-085-00 METAL CHIP 33K 5% 1/10W (EXCEPT EE, CIS)
! R12 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R1703 1-216-069-00 METAL CHIP 6.8K 5% 1/10W (EE, CIS)
R1706 1-216-049-11 METAL CHIP 1K 5% 1/10W !R13 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R1707 1-216-097-00 METAL CHIP 100K 5% 1/10W (EE, CIS)
R1711 1-249-429-11 CARBON 10K 5% 1/4W (EE, CIS)

– 109 –
HCD-GRX9000/RX900
TRANSFORMER
! R14 1-219-120-11 FUSIBLE 0.15 5% 1/4W F #11 7-628-254-15 SCREW +PS 2.6X6
(EXCEPT EE, CIS) #12 7-628-254-50 SCREW +PS 2.6X16
************************************************************
< SWITCH >
ACCESSORIES & PACKING MATERIALS
! S11 1-771-291-11 SWITCH, POWER (VOLTAGE SELECTOR) *******************************
(EXCEPT EE, CIS)
1-475-572-11 COMMANDER, STANDARD (RM-SR5)
< TRANSFORMER > 1-501-374-11 ANTENNA, LOOP
1-501-659-41 ANTENNA (FM) (EXCEPT EE, CIS)
! T11 1-431-662-11 TRANSFORMER, POWER (EE, CIS) 1-501-804-11 ANTENNA (FM) (EE, CIS)
! T11 1-431-663-11 TRANSFORMER, POWER (EXCEPT EE, CIS) 3-862-005-11 MANUAL, INSTRUCTION (ENGLISH)
************************************************************
3-862-005-21 MANUAL, INSTRUCTION (FRENCH, SPANISH)
MISCELLANEOUS (E, EA, MY, SP)
************** 3-862-005-41 MANUAL, INSTRUCTION (CHINESE)
(EA, MY, SP)
6 1-769-984-11 WIRE (FLAT TYPE) (13 CORE) (23cm) 3-862-005-51 MANUAL, INSTRUCTION (ARABIC) (EA)
10 1-773-048-11 WIRE (FLAT TYPE) (17 CORE) 3-862-005-91 MANUAL, INSTRUCTION (POLISH, RUSSIAN)
11 1-773-025-11 WIRE (FLAT TYPE) (15 CORE) (33cm) (EE, CIS)
105 1-783-570-11 WIRE (FLAT TYPE) (19 CORE) 4-991-151-21 COVER, BATTERY (for RM-SR5)
107 1-693-420-11 TUNER (FM/AM) (E)
107 1-693-421-11 TUNER (FM/AM) (EA, MY, SP)

108 1-769-976-11 WIRE (FLAT TYPE) (13 CORE) (14cm) (E)
108 1-773-008-11 WIRE (FLAT TYPE) (15 CORE) (14cm)
(EXCEPT E)
! 113 1-575-651-11 CORD, POWER (EE, CIS, EA, MY, SP)
! 113 1-575-653-11 CORD, POWER (E)
! 114 1-569-008-21 ADAPTOR, CONVERSION 2P (EA, MY, SP)

257 1-452-925-21 MAGNET ASSY
258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE)
! 301 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP
302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)
HP101 A-2056-681-A DECK (A) ASSY, HEAD (230AWR1)

HP101 A-2056-683-A DECK (A) ASSY, HEAD (230PWR1)
HRPE101A-2056-682-A DECK (B) ASSY, HEAD (230AWR1)
HRPE101A-2056-684-A DECK (B) ASSY, HEAD (230PWR1)
M1 A-2004-628-A MOTOR ASSY, CAPSTAN
M101 X-4917-523-4 MOTOR ASSY (SPINDLE)

M102 X-4917-504-1 MOTOR ASSY (SLED)
M401 1-763-072-11 FAN, D.C.
M701 A-4672-004-A MOTOR ASSY (TURN)
M801 A-4672-004-A MOTOR ASSY (SLIDE)
S811 1-473-335-11 ENCODER, ROTARY (BU, TRAY ADDRESS DET)

! T11 1-431-662-11 TRANSFORMER, POWER (EE, CIS)
! T11 1-431-663-11 TRANSFORMER, POWER (EXCEPT EE, CIS)
************************************************************
**************
HARDWARE LIST
**************
#1 7-685-872-09 SCREW +BVTT 3X8 (S)

#2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#5 7-685-871-01 SCREW +BVTT 3X6 (S)
#6 7-685-880-09 SCREW +BVTT 4X6 (S)

#7 7-685-851-04 SCREW +BVTT 2X4 (S)
#8 7-621-775-10 SCREW +B 2.6X4
#9 7-621-255-15 SCREW +P 2X3 The components identified by mark ! or dotted
#10 7-685-850-04 SCREW +BVTT 2X3 (S) Replace only with part number specified.
Sony Corporation 98F0531-1

Printed in Japan © 1998. 6
9-922-877-11 Home A&V Products Company Published by Quality Assurance Dept.
– 110 – (Shibaura)

HCD-GRX9000/RX900: Service Manual

Uploaded by

Copyright:

Available Formats

HCD-GRX9000/RX900: Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HCD-GRX9000/RX900: Service Manual

Uploaded by

Copyright:

Available Formats

HCD-GRX9000/RX900

SERVICE MANUAL East European Model

HCD-GRX9000/RX900 are the Amplifier,

– Continued on next page –

MINI Hi-Fi COMPONENT SYSTEM

Downloaded from www.Manualslib.com manuals search engine

6. ELECTRICAL ADJUSTMENTS NOTES ON LASER DIODE EMISSION CHECK

8. EXPLODED VIEWS ................................................ 86

9. ELECTRICAL PARTS LIST ............................... 95

MODEL PART No.

SAFETY-RELATED COMPONENT WARNING!!

1 Remove the Case.

3 Pull-out the disc tray.

2 Turn the cam to the

NOTE FOR INSTALLATION (ROTARY ENCODER)

Note:When attaching the Base unit, Insert the

Note:When attaching the BU cam,

@¢ Fluorescent indicator tube

FRONT PANEL SECTION

5 wire (flat type)

7 wire (flat type)

CD MECHANISM DECK SECTION (CDM38LH-5BD29AL)

2 wire (flat type) (19 core) (24 cm)

4 CD mechanism deck section

Note: The CD mechanism deck will

3 two screws 3 screw

2 wire (flat type) (13 core) (14 cm)

4 two screws 5 connector

[Change-over of FUNCTION Name]

2) Operation during aging Mode

test tape MAIN board

test tape MAIN board

Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301

6. Confirm playback the signal recorded in step 3 become ad-

tomatically switch to VIDEO. PB LEVEL REC BIAS PB LEVEL

2. Insert a tape into deck B. (NORMAL) (HIGH)

MW Tuned Level Adjustment

FM Tuned Level Adjustment

Adjustment Location: TCB board

Carrier frequency : 69 MHz

S Curve Check Procedure:

6. Press the p button, [ENTER/NEXT] button and ^ button

RF Level Check Traverse waveform

[BD BOARD] (Conductor Side)

AMP (R) board

HP board AMP (L) board

MOTOR (SLIDE) board

ST +10V • SIGNAL PATH

FE2 POLAR /PILOT SWITCH

Q13 LW SWITCH AM TP1702 SWITCHING SWITCHING

SWITCH X42 X41

Downloaded from www.Manualslib.com manuals search engine

7-2. BLOCK DIAGRAM – CD Section –

SERVO AUTO SEQUENCER

LEVEL SHIFT DISC SENSOR

18 FOCUS IN3B OUT OP–

OUT2A IN2A SLO SLP

SLED SERVO FIN OUT1

Downloaded from www.Manualslib.com manuals search engine