Digital Point Load Test Apparatus

77-0115

OPERATING INSTRUCTIONS
Digital Point Load Test Apparatus

77-0115

ELE International Distributor: ELE International

Chartmoor Road, Chartwell Business Park Soiltest Product Division
Leighton Buzzard, Bedfordshire, LU7 4WG PO Box 389, Loveland, CO 80539
England USA
phone: +44 (0) 1525 249200 phone: +1 (800) 323 1242
fax: +44 (0) 1525 249249 fax: +1 (970) 663 9781
email: ele@eleint.co.uk email: soiltest@eleusa.com
http://www.ele.com http://www.eleusa.com
ELE International, a division of Hach Lange Ltd.

In the interests of improving and updating its equipment, ELE reserves the right to alter specifications to equipment at any time.
ELE International 2015 

1 9907X0043 Issue 3
Contents

Section Page

1 Introduction 3

2 Specification 4

3 Installation and Setting Up 5

4 Operation 5

5 Calculations 7

6 Testing Concrete Cores 11

7 Maintenance 12

8 References 13

Appendix 1 : Bibliography 14

Appendix 2 : Load Cell Indicator : SLIM –

A. Operating Manual 16

B. Installation Manual 30

WEEE Directive
Prologue
The index s is determined from the formula P/D² where D is the distance between the point
load platens at the moment of failure and P the force required causing the failure.
Considerable work has been conducted on this method of strength determination but only
recently is this being related to the field study of specimens. The following is an excerpt from
an article ‘Logging the Mechanical Character of Rock’ by Dr J A Franklin, Mr E Broch and Mr
G Walton in Transactions of the Institute of Mining and Metallurgy volume 80, which
adequately introduces the technique.
‘The Strength Log –
Traditionally, rock strength is either estimated in the field by use of a hammer or in the
laboratory with sophisticated apparatus. The former method is at best qualitative, whereas
the latter requires careful specimen preparation. There is an obvious need for a device to
test quickly and reliably, unprepared core in the field.
A portable point load tester has been developed at Imperial College, London, as an aid to
core logging. The apparatus consists of a small hydraulic pump and ram, with a loading
frame of maximum rigidity easily adjustable to test core of different sizes. Core is loaded
between pointed platens of standard dimensions. The two quantities measured in the test are
the distance, D, between platen contact points, which is read from a graduated scale
incorporated in the load frame, and the force, P, required to break the specimen, which is
read from a calibrated readout unit in the hydraulic circuit. The point load strength index, s, is
the ratio P/D².
This type of test is not new, having been used extensively in the USA, Russia and several
European countries, but mainly as a research laboratory tool rather than as a convenient
technique for field index testing. Theoretical consideration of the point load test showed that
it gives a measure of tensile strength, as indeed does the geological hammer. The results
are, however, sufficiently related to other measures, such as unconfined compressive
strength, to allow this test to give an index of strength in a general sense. The point loading
gives several important advantages:
A the specimen fails at much lower loads than in compression, needing a machine
load capacity less than one-tenth of that usually required for compression;
B core can be tested direct from the core box without previous machining – even weak or
broken rock can thus be tested;
C as fracture initiates in the specimen interior, platen contact conditions are of little
importance.
1 Introduction
The ELE Point Load Apparatus comprises a two-column fixed crosshead frame
mounted directly onto a hand-operated hydraulic jack.
Pressure applied by the handpump in the base of the jack extends the piston carrying
the lower of the two conical points. The upper point is fixed to the crosshead and the
frame can accommodate sample sizes up to 101.6 mm (4 in.) in diameter. A scale is
fitted to indicate the distance between contact points (D).
The applied load is indicated directly in kN on the digital readout display unit. The
maximum load achieved during the test is then held and displayed until the readout is
zeroed ready for the next test.
The apparatus is supplied with a heavy-duty face mask for operator protection.
2 Specification
Case dimensions 320 x 715 x 370 mm (width x height x depth)
Overall weight 25 kg
Load capacity 55 kN
Specimen
max. diameter 101.6 mm
Oil Shell Tellus 37. Note: If T 37 is unavailable
then either T 32 or T 46 may be used but do
not mix oils of different specifications.
Working temperature range +5 Deg C to +40 Deg C
Recommended humidity range 30% to 95%
Batteries 4 X AA

Fig. 1

2.1 Load frame and case general layout (figure 1)

2.1.1 Comprises a two column fixed crosshead frame (2) attached by a bolt (5) to the
hydraulic ram assembly (6).
2.1.2 Load is applied to the specimens through two standard hardened points (1).
2.1.3 Attached to one column is a millimetre scale (3) used in conjunction with the pointer
(4) to determine the specimen dimensions ‘D’ between the two load points at the start
of the test.
2.1.4 The hydraulic piston assembly incorporates the oil reservoir, a single acting pump,
pressure relief valve (9), and a handle (8) for pumping and pressure release control.
2.2 Case and accessories (figure 1)
2.2.1 The unit is contained in a case (12) that can convert to a workbench for testing.
2.2.2 A clear see-through face mask is provided, essential to avoid injury and damage due
to debris that can fly at time of failure, particularly when testing hard rock.
3 Installation & Setting Up
3.1 Place the point load tester case (12) onto a flat surface.
WARNING: When lifting take care that the machine is conveniently held and
secured and that it cannot slide.
3.1.1 Remove the top cover of the point load tester.
3.1.2 Check that all accessories are present:
a) Pump handle,
b) Face protection mask.
3.1.3 If ram fails to move to its full extension during testing then check oil level (see section
7 on maintenance for the oil filling procedure).
3.1.4 If ram moves in jerky movements, pump ram to its maximum position and carefully
turn the whole assembly upside down, taking care not to damage the readout unit,
then force the ram back to its original position and turn the unit up the correct way.
This process should remove all the air from the ram and the ram should now move
smoothly to pump strokes.
3.2 The digital readout unit has a range of user settings which need to be set before
testing commences.
3.2.1 To switch on the digital display refer to Appendix 2. The readout unit will shut down
automatically after 30 minutes (Factory Default) if no keys are pressed in this time.
4 Operation
4.1 Switch on the digital display press the [ON] button and initiate the peak hold function
by pressing the [PEAK] button for 1 second until the PEAK+ status sign shows on the
top of the digital readout screen.
4.1.1 The digital readout is now ready for operation.
4.1.2 Basic diametral test procedure (Figure 1 and 8a).
4.1.3 Select a core to be tested.
4.1.4 Close the pressure release valve (9).
4.1.5 Place the core diameter between the load points (1).
4.1.6 Using the pump handle (8), raise the lower point slightly, and zero the reading by
pressing the [ZERO] button for approximately 3 seconds until the reading is set to
zero. Then pump the ram up to make firm contact with the specimen.
4.1.7 Measure the diameter ‘D’ of the specimen from the scale pointer (4).
4.1.8 Record ‘D’ to an accuracy of ±2%.
4.1.9 Check the PEAK+ status is showing on the digital readout.
Important: The face mask for eye protection should be worn at this point.
4.1.10 Steadily apply the load using the pump handle to cause failure of the specimen within
the period 10 to 60 seconds.
Note! Do not exceed the 100% indicator during loading.
4.1.11 Record the maximum load achieved on the screen after sample failure. Press zero to
reset readout.
4.1.12 Open the pressure release valve (9) and manually force the lower platen down using
the pump handle horizontally ready for the next specimen to be tested.
4.2 The axial test (figure 8b)
4.2.1 Where the specimen length/diameter ratio is between 0.3 and 1.0, the axial test can
be used.
4.2.2 Locate the specimen with the ends contacting the platen points.
4.2.3 Proceed as in 4.1.4.
4.3 The block and irregular lump test (figures 8c and 8d)
4.3.1 Where the specimen size is 50 ± 35 mm and of suitable shape, the block test can be
used.
4.3.2 The ratio of depth/width should be between 0.3 and 1.0 and preferably nearer to 1.0.
4.3.3 Place the specimen with the smallest dimension between the platen points.
4.3.4 Proceed as for the basic test 4.1.4.
Note: for irregular lumps, calculate W from the formula:
W = W1 + W2
2
Where W1 is opposite to W2.
4.3.5 It is recommended that a minimum of 10 specimens are tested to obtain a mean
point load index value s.
4.4 Anisotropic rock (figure 9)
4.4.1 Where the rock exhibits anisotropic properties, the sample should be tested in both
directions.
4.4.2 Using the diametral and axial techniques, it is recommended that at least 10
specimens are tested parallel to and perpendicular to the weakest plane of the
sample.
4.4.3 The strength Anisotropic Index a is defined as the ratio of mean s values measured
perpendicular and parallel to planes of weakness.
5 Calculations
5.1 Uncorrected point load strength (table 1)
5.1.1 The uncorrected point load strength value s is calculated as:
P/De²
where De² the equivalent, core diameter is given by:
De² = D² for diametral tests
De² = 4A/ for axial, block and lump tests
and
A = WD = minimum cross sectional area of a plane through the platen contact points.
5.1.2 The Nomogram Table 1 offers a quick method to determine the uncorrected point
load strength value s.
5.2 Point load strength correction (figure 10)
5.2.1 The point load strength index will vary slightly with specimen diameter ‘D’. To
overcome this, it is common practice to relate the test to that for specimens of 50
mm diameter.
5.2.2 To obtain the maximum accuracy and repeatability it is therefore recommended
that tests are conducted on specimens as near as possible to 50 mm diameter.
5.2.3 The most reliable method of size correction is to test the sample over a range of D
or De² and to plot graphically the relationship between P and De. If a log-log plot is
used, the relationship will follow closely to a straight line.
5.3 Result tabulation (figure 11)
5.3.1 It is recommended that results are collated in a similar manner to that shown.
Table 1 Nomogram for computing point load strength s = P
D2
6 Testing Concrete Cores
6.1 Development of the technique
6.1.1 In 1980 a research programme was reported by Mr P J Robins (Department of Civil
Engineering, Loughborough University of Technology), related to the use of the point
load tester for testing concrete cores as a method of determining the comparative
compressive strength of in-situ material.
6.1.2 The technique was reported in the Magazine of Concrete Research : Vol. 32, No.
111 : June 1980. Some fundamental points are listed below for those interested in
considering the technique.
6.2 Specimen size
6.2.1 A value of 4 is suggested as a minimum ratio of core diameter to maximum
aggregate size.
6.2.2 The minimum value for the length/diameter ratio of test cores should 1.2.
6.3 Point load index/compressive strength
6.3.1 The point load index can be directly related to the cube compression test for a
given concrete mix providing the size relations detailed above can be maintained.
6.3.2 The use of 100 mm diameter cores will achieve a coefficient of variation similar to that
for compressive tests on similar diameter cores.
6.4 Test procedure (figures 8 and 12)
6.4.1 The test procedure will be similar to that for diametral or axial rock tests.
6.4.2 Where possible, laboratory design tests should be used to define the relationship
curve between the point load index and the compressive strength of the concrete.
7 Maintenance
7.1 General
7.1.1 Keep the unit clean and free from debris.
7.1.2 Check for low batteries in the digital readout unit. Change when necessary (4 X AA).
7.1.3 Check regularly for signs of oil leaks.
7.1.4 Check the oil level in reservoir and top up as necessary with correct oil using the
following procedure.
7.1.5 If the oil reservoir is low and the ram fails to reach maximum travel, follow the
procedure below to fill the reservoir. Note: the units are normally supplied filled with
the correct amount of oil. It is recommended to check the level every 3 to 6 months.
7.1.6 If the oil reservoir in the hydraulic pump body (6) requires filling with the appropriate
oil, see specification for oil details.
7.1.7 Remove the oil filler cap (7). Note: only add oil with the ram at its lowest position.
7.1.8 Lay the unit on its side with rubber filler plug uppermost and using a funnel fill the
reservoir. NOTE: do not overfill as the reservoir is full when the oil level is at the filler
port when the unit is in its normal standing position. Replace rubber plug.
7.1.9 To test, close the pressure release valve (9) (fully clockwise), engage the pump
handle and pump some strokes, and the ram should be seen to rise. If successful,
release the pressure relief valve and push the ram down to its original start point
using the pump handle in the horizontal position.
Note: Please dispose of any waste oil in a correct manner according to local rules.
7.2 Check the platen points for damage and replace as necessary.
7.3 If the hydraulic pump is leaking or not functioning correctly, contact the
ELE Service Department for advice.
7.4 If the main piston is leaking oil past the seal, the piston seals might need
replacing (contact ELE Service Department for advice).
7.5 Default settings for the readout unit. Press and hold the SET button to enter change
options. Press the SET button again to step through options until required option
shows. It is then suggested to only modify the options marked user definable
below.

UNIT user definable (kN,kgf)

FL = 15 Fixed
R = 01 Fixed
OFF = 30 user definable (1 – 30)
BAUd = 0 Fixed

Note the calibration section within the readout is guarded by a password. If for some
reason you need to re-calibrate the unit contact the ELE service department.
8 References
8.1 ISRM Commission on Testing Methods Working Group on Revision of the Point Load
Test Method.
8.2 The Point Load Strength Test for Concrete Cores, P J Robins, Magazine of Concrete
Research, Vol. 32, No. 111, June 1980
Appendix 1
Bibliography

From the ISRM Commission on Testing Methods

Bieniawski, Z.T., The Point Load Test in Geotechnical Practice, Eng. Geolo., 9, 1 – 11
(1975).
Boisen, B.P., A Hand Portable Point Load Tester for Field Measurements. Proc. 18th US
Symp. on Rock Mech., Keystone, Colorado, 1 – 4 (1977).
Broch, E. and Franklin, J.A., The Point Load Strength Test. Int. J. Rock Mech. Min. Sci., 9,
669 – 697 (1972).
Broch, E., Estimation of Strength Anisotrophy using the Point Load Test, Int. J. Rock Mech.
and Min. Sci., 20, 181 – 187 (1983).
Brook, N., A Method for Overcoming Both Shape and Size Effects in Point Load Testing.
Proc. Conf. on Rock Engineering, Univ. Newcastle, England, 53 – 70 (1977).
Brook, N., Size Correction for Point Load Testing. Tech. Note in Int. J. Rock Mech. Min. Sci.
& Geomech. Abstracts, 17, 231 – 235 (1980).
Fitzhardinge, C.F.R., Note on Point Load Strength Test. Australian Geomech. J., G8, p.53
(1978).
Forster, I.R., Influence of Core Sample Geometry on the Axial Point Load Test. Tech. Note,
Int. J. Rock Mech. Min. Sci. 20, 291 – 295 (1983).
Franklin, J.A., Broch, E., and Walton, G., Logging the Mechanical Character of Rock. Trans.
Inst. Min. Met. UK., 80, A1 – A9 (1971), and discussion 81, A43 – A51 (1972).
Gartung, E., Empfehlung Nr. 5 des Arbeitskreises 19 – Versuchstechnik Fles – der
Deutschen Gesellschaft fur Erdund Grundbau e.V. Punktlastversuche an Gesteinsproben.
Die Bautechnik, Vol. 59, No. 1, pp 13 – 15 (1982).
Greminger, M., Experimental Studies of the Influence of Rock Anistropy on Size and Shape
Effects in Point Load Strength Testing. Tech. Note, Int. J. Rock Mech. Min. Sci. 19, 241 –
246 (1982).
Guidicini, G., Nieble, C.M., and Cornides, A.T., Analysis of Point Load Test as a Method for
Preliminary Geotechnical Classification of Rocks. Bul. Int. Assoc. Eng. Geol., 7, 37 – 52
(1973).
Hassani, F.P., Scoble, M.J. and Whittaker, B.N., Application of the Point Load Index Test to
Strength of Rock, and Proposals for a New Size-correction Chart, Proc. 21st US Symp. Rock.
Mech., Rolla, Mo., 543-556 (1980).
Int. Soc. Rock Mech., Suggested Method for Determining the Point Load Strength Index, Int.
Soc. Rock Mech. (Lisbon, Portugal), Committee on Field Tests, Document No. 1 8 – 12
(1972).
Lajtai, E.Z., Tensile Strength Measurement and its Anisotropy Measured by Point – and Line-
loading of Sandstone. Eng. Geol., 15, 163 – 171 (1980).
Pells, P.J.N., The Use of the Point Load Test in Predicting the Compressive Strength of Rock
Materials. Austral. Geomch. J., G5, 54 – 56 (1975).
Peng, S.S., Stress Analysis of Cylindrical Rock Discs Subjected to Axial Double Point Load,
Int. J. Rock Mech. Min. Sci., 13, 97 – 101 (1976).
Read, J.R.L. Thornton, P.N. and Regan, W.M., A Rational Approach to the Point Load Test.
Proc. 3rd Austral. New Zealand Conf. on Geomech., Wellington, 2, 35-39 (1980).
Reichmuth, D.R., Point Load Testing of Brittle Materials to Determine Tensile Strength and
Relative Brittleness. Proc. 9th U.S. Symp. Rock Mech. Colorado (1968).
Robins, R.J., The Point Load Test for Concrete Cubes, Mag. Conc. Res., 32, 101 – 111
(1980).
Wijk, G., Some New Theoretical Aspects of Indirect Measurements of the Tensile Strength of
Rocks. Int. J. Rock Mech. Min. Sci, 15, 149 – 160 (1978).
Wijk, G., The Point Load Test for the Tensile Strength of Rock. Geotechnical Testing Journal,
49 – 54, June (1980).
Appendix 2 : A

Load Cell Indicator : SLIM

Operating Manual
Contents Page

OPERATING FEATURES :

A. Display Views 18

B. Keyboard Functions 19

C. Operating Functions 20

SET UP :

D. Weight Data Menu (Theoretical Calibration) 21

E. Weight Calibration and Linearization Menu 22

F. Weight Parameters Menu 23

G. RS485 Serial Communication Port Menu 25

H. Password Access Menu 26

I. Serial Communication Protocols 27

OPERATING FEATURES :

A. Display

Views Operation

On the 5-digit numerical display the current weight is usually displayed. When the “PEAK”
function is activated, the maximum weight value is displayed. During setup steps, the
displayed messages and values shown depend on the programming function in execution.

Power On
Display test is executed at instrument power on. An ID code is then
displayed representing software and version number. Please remember
to communicate this ID code in case of a service request.

Weight Views and Error Messages

When there are no programming procedures in progress, the weight value is displayed.
Some error conditions are highlighted on the display as follows:-

WEIGHT INVALID AT POWER ON

When the instrument is switched on, during initialization and while
the weight is not zero, this alert appears on display.

OVERLOAD CONDITION
When the gross weight exceeds the maximum capacity for more
than 9 divisions, this alert appears on the display.

UNDERLOAD CONDITION
When the gross weight is less than -9999, this alert appears on the
display.

LOAD CELL CABLE NOT CONNECTED

LOAD CELL SIGNAL UNDER NEGATIVE RANGE LIMIT

Load cell signal is lower than –7.81mV/V. This may be a
connection error.

LOAD CELL SIGNAL OVER POSITIVE RANGE LIMIT

Load cell signal is higher than +7.81mV/V. This may be a
connection error.

CONNECTION ERROR CONDITION

Load cell is not connected correctly.

INTERNAL FAULT CONDITION

There is an internal fault relating to the weight acquisition system.

WEIGHT NOT YET CALIBRATED

B. Keyboard

Functions Menu

Navigation

Numerical Value Setting

Select Value
C. Operating
Functions Autotare

The autotare command has no effect with an unstable weight (timeout 2 sec.). Parameter 0
BND represents the maximum weight value that can be zeroed (positive or negative),
compared to the zero value stored during calibration operations.
Peak Functions

Peak weight value is displayed alternatively with PEAK

message.

The peak value is always stored, even when not displayed. It is stored both for positive and
negative weight values. The peak value is lost after power off. The peak value is stored at
weight acquisition frequency (see weight filter).

Set Up Menu

Password access is requested only if a password was set.

Select “End” to Exit menu.
SET UP :

D. Weight Data Menu (Theoretical Calibration)

WEIGHING SYSTEM CAPACITY

Enter the total capacity of the load cell/s in kg. This value represents the
weighing system’s full scale. Values between 1 and 99000 kg are
accepted. By modifying the weighing system’s full scale value, the
theoretical calibration will be done.
LOAD CELL SENSITIVITY
Enter the average value of the sensitivity rated value of the load cell/s in
mV/V. Values between 0.5 and 4 mV/V are accepted. If no value is set
the default value 2 mV/V will be used. By modifying the sensitivity’s
value, the theoretical calibration will be done.
DIVISION VALUE
This value is represented in kg. Select a value between 0.001 kg and 50
kg. The ratio between the weighing system total capacity and the
display division value represents the resolution of the instrument. By
modifying the weighing system capacity, a new division value will be
automatically set to obtain a system resolution at the best of 10000
divisions. The system resolution must be set from 500 to 100.000
divisions. By modifying the division’s value, if weighing system’s full
scale value has not been changed, the weight calibration will be
automatically corrected.
E. Weight Calibration and Linearization Menu

During the calibration procedure the message “CAL” blinks on the display.
During the linearization procedure the message “LIN n” blinks on the display: N is the
number of the linearization point you are programming (N range: from 1 to 5).

The zero calibration must be done when the weighing system is

ZERO unloaded (tare included). Weight must be stable. The weight
CALIBRATION displayed will be zeroed. This procedure can be repeated more
times.
Load a known weight (sample weight) on the weighing system and
wait for the stabilization; the display shows the value to be
FULL SCALE calibrated.
CALIBRATION If the value just entered is higher than the maximum available
resolution, the full scale calibration is not accepted and the display
shows an error message. This procedure can be repeated more
times.
Up to 5 linearization points can be set, in weight ascending order
(from 1 to 5). During a linearization point procedure, the display
shows the current weight alternately with message “LIN n”. After
WEIGHT setting the corresponding value, the procedure switches
LINEARIZATION automatically to next point (N+1).

To exit without setting all 5 linearization points, press key:

only the points entered will affect the new weight linearization.
F. Weight Parameters Menu

DIGITAL FILTER VALUE

This parameter adjusts the working of the digital filter, this parameter is
applied on the weight. The digital filter affects the visualization of the
weight. Low digital filter values cause very fast updates of the weight,
whereas high values cause slow updates of the weight.

Filter Value Weight update rate Response (Hz)

0 16,7 Hz 3
1 16,7 Hz 2,5
12,5 Hz 1,5
3 (default) 12,5 Hz 1
4 10 Hz 0,7
5 10 Hz 0,55
6 8,3 Hz 0,4
7 6,2 Hz 0,35
8 6,2 Hz 0,3
9 4 Hz 0,25
WEIGHT STABILITY
The weight is considered stable when it remains in a given range, within a
given period of time.

Value Weight range Time range

0 Always stable
1 10 div. 1.5 sec.
2 5 div. 2 sec.
3 3 div. 2 sec.
4 1.5 div. 2.5 sec.
AUTOZERO AT POWER ON
This parameter is the maximum value that can be zeroed at the power-on.
The autozero function performs the automatic zero calibration when the
instrument is switched on, but only if the weight present on the weighing
system stabilizes within the zero-set-point value. Set 0 to disable this
function.
Value Variation
0 Function disabled
1 0.5 div / sec.
2 1 div / sec.
3 2 div / sec.
4 3 div / sec.
ZERO BAND
Maximum weight value that can be zeroed through autotare command,
compared to the zero value stored during calibration operations. Set 0 to
enable full range of zeroing (from 0 to capacity).

LOAD CELL SIGNAL

The real-time load cell signal will be displayed in mV/V (3 decimal digits).
G. RS485 Serial Communication Port Menu

BAUD RATE
Select a value: 9600, 19200, 38400, 57600 e 115200 bit / sec.

COMMUNICATION PROTOCOL

 CONT: Weight continuous transmission (5 Hz transmission frequency).

 SLAVE: MASTER / SLAVE ASCII protocol.

DATA FORMAT
Select combination for parity / data bits number / stop bits number.

COMMUNICATION ADDRESS
Address used for master/slave protocols (from 0 to 99).
H. Password Access Menu

SETUP MENU PASSWORD

This parameter is the password which protects setup menu access.

The modification or cancellation of the password is only possible

from setup menu, which is accessed by entering the active
password .
I. Serial Communication Protocols
Continuous Transmission Protocol
This protocol can be used to drive a weight repeater.
String transmitted at 5 Hz:
STX <status> <net weight> ETX <csum> EOT
<status> = 1 byte, see following table (bit = 1 if the condition is TRUE)

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Tare Stable
0 0 1 1 entered 0 weight 0

<net weight> = 8 ASCII bytes, weight value is right hand justified.

If overload condition: “^^^^^^^^”.
If underload condition: “-------------- ”.
If weight reading error “ O-L “.

<csum> = string data control sum. It is calculated executing the exclusive OR (XOR) of all
characters from STX (or from <addr>) to ETX, excluding the latter; the XOR result is
resolved into 2 characters considering the 4 highest bit (first character) and the for lowest
bit (second character) separately; the 2 resulting characters are then coded in ASCII; (e.g.:
XOR = 5Dh; <csum> = "5Dh" i.e. 35h and 44h).

“SLAVE” Transmission Protocol

AVAILABLE COMMANDS:
 Current net weight request.
 Current gross weight request.
 Current peak value request.
 Autotare command.
 Peak reset command.

The unit connected to the instrument (usually a personal computer) is the master-unit and is
the only unit that can start a communication procedure.

The communication procedure must always start with the transmission of a string by the
master-unit, followed by a response string from the interested slave-unit.

COMMAND FORMAT DESCRIPTION:

The quotes enclose the constant characters (attention to capital / lowercase characters); the
symbols < and > enclose variable numerical fields.
Current Net Weight Request

Current Gross Weight Request

Current Peak Value Request

Autotare Command

Peak Value Reset Command

In case of communication error, or in case the command is not correctly recognized,

the instrument will respond with the following string:
Fields Description

The quotes enclose the constant characters (attention to uppercase / lowercase characters);
the symbols < and > enclose variable numerical fields.
STX (start of text) = 0x02h, ETX (end of text) = 0x03h, EOT (end of transmission) = 0x04h,
ACK (acknowledge) = 0x06h, NAK (No acknowledge) = 0x15h.
<Addr> = Serial communication address + 0x80h (e.g.: address 2: <Addr> = 0x82h (130 in
decimal format)).
<status> = 1 byte, see following table (bit = 1 if condition is TRUE).

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Tare Stable
0 0 1 1 entered 0 weight 0

<gross>, <net>, <peak> = 8 ASCII bytes, weight value is right hand justified (without non-
significant zeroes, with decimal point and negative sign).
If overload condition: “^^^^^^^^”.
If underload condition: “------------- ”.
If weight reading error “ O-L “.
<csum> = string data control sum. It is calculated executing the exclusive OR (XOR) of all
characters from STX (or from <addr>) to ETX, excluding the latter; the XOR result is
resolved into 2 characters considering the 4 highest bit (first character) and the for lowest
bit (second character) separately; the 2 resulting characters are then coded in ASCII;
(e.g.: XOR = 5Dh; <csum> = "5Dh" i.e. 35h and 44h).
Appendix 2 : B

Load Cell Indicator : SLIM

Installation Manual
Contents Page

MAIN FEATURES :

A. Technical Features 32

B. Symbols 33

C. Identification Data Plate 33

D. Warnings 33

CONNECTIONS :

E. Power Supply 34

F. Load Cell Wiring 34

G. RS485 Serial Wiring 35

H. Can Bus Wiring 35

I. Summary of Wiring 36
MAIN FEATURES :

A. Technical Features

5 - 13Vdc polarity inversion protection.

Power supply Protection with replaceable fuse.
Power consumption 1.5 W
Isolation Class III
Operating temperature -10°C  +50°C (max humidity 85% non-condensing)
Storage temperature -20°C  +60°C

Weight display 5 digit red LED’s, 7 segments, (h 10 mm)

Keyboard 3 mechanical keys

Circuit overall dimensions 76 mm x 29 mm x 22 mm (l x h x p)

Mounting Inside load cell / other containers
Connections Solder pads or AMP2 connectors

Load cells: max 2 350 Ohm parallel load cells (or 4 700 Ohm load cells).
Load cells power supply 3.3Vdc
Linearity < 0.01% of full scale
Temperature drift < 0.001% of full scale / C°
A/D converter resolution 24 bit
Input signal range From -3.9 mV/V to +3.9 mV/V
Digital filter From 0.25 Hz to 3 Hz selectable
Weight decimal digits from 0 to 3 decimal digits
Zero and full scale calibration Executable via keyboard
Load cells cable fail check Always working

Rs485 half duplex

Serial ports (optionals) CAN bus

Code memory 32 Kbytes

Data memory 2 Kbytes

Conformity to standards EN61000-6-2, EN61000-6-3 (EMC)

EN61010-1 (Electric safety)
B. Symbols

A list of the symbols used in the manual are given below:

Caution! Only specialised personnel can perform this operation.

Read the following instructions carefully.

Further information.

C. Identification Data Plate

It is important to provide these data when requesting information or

instructions regarding the instrument, along with the program number and
the software version which are shown on the manual cover and are
displayed when the instrument is switched on.

D. Warnings

Only specialised personnel can perform the following operation.

All wiring must be carried out with the instrument switched-off.

The following information concerns all the SLIM’s functions available on

the different models.
E. Power Supply

 The power supply must be wired to connector J5 pin 1 and 2.

 The power supply cable must be channelled separately from other power
supply cables with different voltages, from the load cells cables and from
the I/O cables.

Power supply : 5-13 Vdc max 1.5 W

CONNECTIONS

Pin 1 on J5 + Alim.
Pin 2 on J5 GND

F. Load Cell Wiring

 The load cell cable must not be channelled with other cables (i.e. Outputs
connected to remote switches or power supply cables), but must follows its
own route.
 Any cable extension must be carefully shielded, the colour code must be
respected and a cable of the same type as the one provided from the
manufacturer must be used. The extensions on the cables must be
soldered, otherwise a supportive terminal block or a junction box must be
used.
 The load cell cable shouldn’t have more conductors than those effectively
used (4 or 6). In case of a cable with more conductors, connect those
unused wires to the –power supply (terminal block 2).

A maximum of 4 x 350-ohm load cells can be connected to the instrument in parallel. The
load cell excitation voltage is 3.3 Vdc and is protected against a temporary short circuit .
The instrument’s input signal range requires the use of load cells with sensitivity from 1 mV/V to 3.9
mV/V. The load cell wires must be connected to terminals 1 ...4 of 4 pins connector (or soldered).

Connect the load cell’s cable shield to the load cell body, or to GND.

NUM. J6
1 + Excitation
2 - Excitation
3 + Signal
4 - Signal
G. RS485 Serial Wiring

 A bipolar shielded cable must be used and the shield must be connected to
GND.

 The cable must not be channelled with other cables (i.e. outputs connected
to remote switches or power supply cables), but must follow its own route.

NUM. J5
1 + ALIM. 6 - 13 Vdc
2 GND
3 CAN H
4 CAN L
5 RS485 +
6 RS485 -

H. Can Bus Wiring

 A bipolar shielded cable must be used and the shield must be connected to
GND.

 The cable must not be channelled with other cables (i.e. outputs connected
to remote switches or power supply cables), but must follow its own route.

NUM. J5
1 + ALIM. 6 - 13 Vdc
2 GND
3 CAN H
4 CAN L
5 RS485 +
6 RS485 -
I. Summary of Wiring

NUM. J6
1 + Excitation
2 - Excitation
3 + Signal
4 - Signal

NUM. J5
1 + ALIM. 6 - 13 Vdc
2 GND
3 CAN H
4 CAN L
5 RS485 +
6 RS485 -
DIRECTIVE ON WASTE ELECTRICAL & ELECTRONIC EQUIPMENT (WEEE)