Service Manual: DBVT1341 Series A

DBVT1341 Series A
SERVICE MANUAL
COLOR TELEVISION/VIDEO CASSETTE RECORDER
ORIGINAL
MFR’S VERSION B
Design and specifications are subject to change without notice.
Downloaded from www.Manualslib.com manuals search engine

DBVT1341
SERVICE MANUAL
COLOR TELEVISION/VIDEO CASSETTE RECORDER
REVISION 1
MFR’S VERSION B
MFR’S VERSION IC4001

A LA71200M-MPB
B LA71201M-MPB
Please file this revision with the original version.

CORRECTION NOTICE
MFR'S INCORRECT CORRECT

VERSION REF.NO. DESCRIPTION REF.NO. DESCRIPTION
A PCB010 SYSCON PCB ASS'Y VMX210A PCB800 SYSCON PCB ASS'Y VMX210A
Change of IC
ELECTRICAL REPLACEMENT PARTS LIST
MFR'S VERSION A MFR'S VERSION B

REF. NO. PART NO. DESCRIPTION PART NO. DESCRIPTION
IC4001 I03F3200M0 IC LA71200M-MPB I03F301MN0 IC LA71201M-N-MPB

R1085 R801R7225J RC 2.2M OHM 1/10W
R4018 R903N8822J RC 8.2K OHM 1/8W R903N8123J RC 12K OHM 1/8W
R4021 R903N8273J RC 27K OHM 1/8W R903N8223J RC 22K OHM 1/8W
R4034 R903N8104J RC 100K OHM 1/8W R903N8823J RC 82K OHM 1/8W
R4044 R801R7104J RC 100K OHM 1/10W R801R7474J RC 470K OHM 1/10W
R4050 R903N8473J RC 47K OHM 1/8W DEL
R4052 R903N8682J RC 6.8K OHM 1/8W R903N8822J RC 8.2K OHM 1/8W
R4053 R903N8562J RC 5.6K OHM 1/8W R903N8682J RC 6.8K OHM 1/8W
C4050 E50HU5010M CE 1 UF 50V E50HU5R22M CE 0.22 UF 50 V
SYSCON PCB ASS'Y (MFR'S VERSION)
PCB800 A57805A01A SYSCON PCB ASS'Y VMX210A A57805A010
VMX210A
SYSCON PCB's are interchangeable.
PRINTED CIRCUIT BOREDS

SYSCON/CRT
(INSERTED PARTS) (CHIP MOUNTED PARTS)
SOLDER SIDE SOLDER SIDE
(MFR'S VERSION B) (MFR'S VERSION B)
ADD W261 ADD R1085

A B C D E F G H
FROM/TO TV POWER
DEGAUSS_H
MICON SCHEMATIC DIAGRAM (SYSCON PCB)
POWER_FAIL2
8 P.CON+5V 8
SERVICE R1032
GND
TP1001 10K
AT+12V C1056
MOTOR_GND 0.1 F NC
SD_SYNC
OSD_R
OSD_G
OSD_BLK
OSD_B
CENTLED
TONE_CTL
100P CH
CAP_CTL
REEL_S
CYL_DRIVE
REEL_T
Y/C_DATA
V.REC_ST_H
SDA
Y/C_CS
Y/C_CLK
H_GND
SCL
C1071
0.1 F
C1065
C1028
0.1 F
TV_POWER_H
C1034
R1007
C1004 100P CH
R1035
CYL/LOADING MOTOR DRIVER
22
10
C1007
R1036 4.7K
IC1004 LB11880 0.1 F
R1031
100P CH
C1061 100P CH
0.1 F
1K
0.0068 B
R1029
R1028
C1035
22K
C1078
100P CH
C1029
0 1.0
C1067
R1021 10
B1001
30
GND FC
R1038 220
R1042 220
1
4.7K FROM/TO Y/C/A/H.AMP

0.1 F 220P CH
3.7 BL01RN1-A63T6
Y/C_CLK
C1060
2.5 CYL_DRIVE 6
29
PC OUT VC 7
2
C1009 220P CH
C1010 220P CH
C1023 220P CH
C1037 390P CH
Y/C_DATA
R1054
560K
C1080 1.9 W919 Y/C_CS

7 5.0 P.CON+5V C1031 7
28
VCO IN VREG R1044

3
H.SW
0.1 B 0.001 B RENT_H
R1017 39K
R1020 22K
R1053 220
C1069 0 3.3K R1033 C1062

2.6 PGIN+ 5.9 SD_VIDEO
27
CX PG IN(+)
4
MTZJ5.6B
R1039 18K
X_RAY 0.2 X_RAY_SW 1K 1 B

0.022 B
D1014
R1045 ENV_DET
C1070 0 Q1023
C1089
0.1 F
2.6
R1075
PGIN-
4.7K
0.0047 B
0 2SC2412K VCR_A_MUTE
26
C2 PG IN(-)
5
3.3K
R1048
C1077
4.7K
0.0022 B W810 CTL+
680P CH
C1073 2.3 2.6
R1034
C1038
CTL-
25
C1 PG OUT1
1M
6
NC NC
0.0022 B 0.9 0.9 0 1.8 2.5 0 0 4.9 2.5 2.6 0 0 4.7 0 0 0 0 0 0 4.8 0 4.9 4.2 0 2.3 1.6 2.1 5.2 0 5.2 C_ROTARY
11.5
0 CYL_PG 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
DUMMY_V.SYNC
24
NC W IN PG OUT2
DRUM-PWM
7
CAP-PWM
VCR_A_MUTE TAB_SW
75 VOLUME
55 VHOLD
52 SD-IN(MONI)
66 V REC START H
SERVICE
68 SDATA
57 NUA
53 OSD-VCC
81
50
REEL-S
60 OSD OUT1
CAP FULL
REEL-T
70 SCLK
67 NC
65 NC
59 V-SYNC
74 JUST CLOCK
61 CENTER LED
69 CS
64 R
63 G
V.REC_ST_H
62 B
54 HLF
58 H/C-SYNC
56 CVIN
73 FF/REW-L
72 IIC-DATA1
11.5 0 71 IIC-CLK1 5.2

0 CYL_FG TV_A_MUTE H.AMP_SW1
23
NC V IN BFGO
82
49
8
5.1 0 COMP
11.5 11.5
83
48
W819 NC
6 SD_SYNC 6
22
NC U IN LVCC 0
9
0
CA/MA_SEL
84
47
CM_ADV_VIDEO/AV1
12.2 11.5 W849 R1001 5.1 0
21
10
VCC VREF
85
46
R1073 1 S811X S811Y POWER_FAIL_L NUB
3.3K 5.9 0 C1046 20P CH
0 IIC_OFF 81 VCR_A_MUTE
86
45
0 LDM_R IIC OFF 50 TAB SW OSC-OUT2 L1001 R1005
20
11
RF X IN R1008 C1013 11 5.2 2.6

R1080 1 CAP_FG 82 TV_A_MUTE 2.2uH 2.7K
87
44
CAP-FG 49 OSD-VSS OSC-IN2
0.0039 2.5 2.5
7.5 0 LDM_F C10911K 1/4W R1040 C1047 18P CH
B 83 SP/LP/EP-H
19
12
M COM Y IN
88
43
AMP-VSS 48 CM_ADV_AUDIO/AV2 CLKSEL
R1084 0 5.2
CYL_FG 0.0022 X 84 CA/MA_SEL 33K FROM/TO CHROMA/IF
0
89
42
10.1 DRUM-FG TUNER_CONTROL NC
1K 1/4W
18
13
W OUT X OUT 13 12 2.0 0 HD

CYL_PG X-RAY_TEST
90
41
DRUM-PG X-RAY_TEST
0 0 0.6 0 VD
R1064 C1015 10V 47 KA
0.0022 B
17
14
V OUT LGND
91
40
C1084
1K 1/4W AMP-VREFOUT VSS C-RESET

2.5 0 8 C1040 18P CH
C1016 16V 22 KA AFT_M
0
92
39
10.1 AMP-VREFIN X-OUT(12MHz)
X1001
16
15
U OUT Y OUT
BOT
2.5 2.6
EOT
5 C1018 50V4.7 KA 12MHz

SCL 5
98 AMP-VCC
93
38
C X-IN(12MHz)
0.2 2.1 SDA
R1009 560 33 E/V_MASK/PLAY LED C1048 18P CH
CTL- 99 ANALOG VCC
94
37
CTL- VCC OSD_R
M-COM
R1012 C1019 C1026

W-OUT
0 32 RENT_H 5.2
U-OUT
V-OUT
R1013 560 C1049 22P CH

CTL+ 10K 0.001 CH 100 DEW 0.01 F OSD_G
95
36
CTL+ 31 ON-TIMER LED XC_OUT(32KHz)
2.5 1.3 X1002
C1020 OSD_B
32.768KHz
96
35
AMP C XC_IN(32KHz)
FF/REW_SW C1027 2.6 1.5 OSD_BLK
C1022 16V10 KA C1050 20P CH
EOT SENSOR Q1004 0 0.0039 B RESET
97
34
13 DUMMY-V.SYNC
CTL AMP-OUT RESET-L AT+5V_BACKUP

15 COLOR ROTARY
DTC124EKA
16 HEAD.AMP.SW
Q1013 2.5 5.2

17 ENV-CMP-IN
0.1 F
22 DEGAUSS_H
14 REMOCON-IN
18 VIDEO-H.SW
PNA2604M010R 10 E/V_MASK AT+5V

6 VIDEO-ENV
98
33
19 HI-FI-H.SW
7 AFT(MONI)
12 CAP-LIMIT
5.1
21 LDM-FWD
5 HI-FI-ENV
23 SENS LED
VCR-POWER
20 LDM-RVS
11 CAP-FWD
8 AFT(REC)
5.1 4.8 VCR_POWER_H

EXT-MUTE
FROM/TO DECK
TV-POWER
0
T-REC LED
25 SPOT H
RENT_H
MSSEN-A
MSSEN-B
0.1
R1011
R1003
REC LED
100 99
32
9 KEY A
10 KEY B
82K
24 SP-H
2.2K
5.2 0 TV_POWER_H
CP1006 (CP101)
BOT
EOT
31
IMSA-9604S-04Z14 5.0 SPOT_H
0 0
1 VCC
D1003 TIMER SYSCON MICON IC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
R1018
2 BOT IC1001
4.7K
SID1050CM 1.4 1.4 0 0 0 2.4 2.2 0 5.2 5.2 0 2.2 0 0 0 5.2 2.3 2.6 2.6 0 0 0 0 5.2 NC 5.2 5.2 0 0
4 LM- OEC7059A NC
NC TV_POWER_H FROM/TO I/O
4
3 LDM- TAB_SW
LM+ VCR_POWER_H
4 LDM+ E/V_MASK
C_ROTARY
RENT_H
TAB SW C1068
3
4
SW1001 9 0.0022 B IIC_OFF

R1002
H.SW
270
SPVF130100 ON_TIM_LED
2
1
H.AMP_SW1 H.SW TV_POWER_H

R1085 2.5 2.6 0 5.2
TP1002 REC_LED
NC 5 6 7 8
2.2 M T-REC_LED
S114Z
VCC
D1004 TEST
S-24C04BDP-LA
SDA
KEY_A
SCL
H.AMP_SW2
EEP ROM IC
KEY_B
IC1099
CAP_F/R W833 1SS133 REMOCON_IN
DUMMY_V.SYNC
SCL
VSS
A2
A1
A0
REMOCON_IN
SDA
0.0022 B
MS_SEN-A
MS_SEN-B
T-REC_LED
C1083
ENV_DET
SEN_LED
REC_LED
W894
W825
SPOT_H
0.01 F
C1082
4 3 2 1
LDM_R
FROM/TO SOUND AMP

LDM_F
AFT_M
KEY_A
KEY_B
3 3
COMP
0 0 0 0
BOT
EOT
FROM/TO MICRO MOTOR TV_POWER_H

TV_A_MUTE
CP1005 (CD2001)
TONE_CTL
MS_SEN-B
MS_SEN-A
IMSA-9604S-07Z14
RESET
REEL_T
SEN_LED
U-OUT
6.3V 100 YK
1 U-OUT FROM/TO DEFLECTION

C1058
V-OUT
2 V-OUT
X_RAY
W-OUT
3 W-OUT X-RAY_TEST
M-COM
4 M-COM TV_POWER_H
6.3V 220 YK
5 GND
R1066
R1047
C1032
R1046
C1064 R1082
4.7K
4.7K
1K
PGIN-
6 PG OUT FROM/TO CM/MOV ADVANCE
1 F 1.5K PGIN+
7 PG GND
CM_ADV_VIDEO
22 1/4W
NC 0 NC
R1079
0
R1019
R1052
CM_ADV_AUDIO
47K
390
C1090 5 4
R1049 CA/MA_SEL
SYSTEM RESET
2 2
R3111N311A/C
NC NC
FROM/TO CAPSTAN DD UNIT 0.0033 B 5.1 MS_SEN A H.AMP_SW2
1.3 Q1009 4.7K
IC1003
SENSOR SW RPI-352Q01R
CP1004 TMC-J08P-B1 1.2
Q1002 1.2 5.2
R1051
0.8 5.2 0
18K
1 GND 2SC2412K 1 2 OUT IN GND

2 3 2 3
2 MOTOR GND 1 2 3
6.3V 220 YK
5.2 5.1 0
C1003_1
3 I LIMIT
CAP_CTL 1 4 1 4
4 CTL 0.8 1.4 0.5 1.4 4 3
5 VCO MS_SEN B 0 0.9 PCB800
25V33 YK
CAP_FG Q1003 REEL SENS

6 FG VMX210
R1050
R1087
C1021
R1083
33K
33K
C1017
100
0.1 F
CAP_F/R RPI-352Q01R Q1005

7 CAP/M/F/R RPI-301
8 VCC(5V)
W882
1
TUNER VIDEO SIGNAL 1
CAUTION: DIGITAL TRANSISTOR
DEFLECTION SIGNAL
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS
CAPSTAN AFC SIGNAL
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER CYLINDER AFC SIGNAL
DURING PLAYBACK CYLINDER APC SIGNAL
A B C D E F G H

SPEC.NO. M578-05A
O/R NO. K175001

CHASSIS EXPLODED VIEW (TOP VIEW)
300
502
348
M2003
UN4001
333 504
334 501
335
H5002 342
336 H5001
314
324 503 347
341
315 306
323
331
508 305 301
508 322
302
312 AA
313
AA
332
AA
AB AB AA
AB
M101
318
304
325 AA
309 AB
319 307 AB 506
AA
345
320 346
AB
AB
507
AB
317 316 AB
321
AB
AB
AB
CLASS PART NO. MARK NOTE: Applying positions AA and AB for the grease
are displayed for this section.
GREASE G-555G AA Check if the correct grease is applied for each
MG-33 AB position.
I-3
CHASSIS EXPLODED VIEW (BOTTOM VIEW)
300
303
510 M2001
AA
339
338 AA
510
AA AA
AA 510
329
337 311
AA AA
AA 310
509 340
308 AB
AB
344 AA
327
343 AA
326
AB
328 AA
505
330
CLASS PART NO. NOTE: Applying positions AA and AB for the grease
MARK
are displayed for this section.
GREASE G-555G AA Check if the correct grease is applied for each
MG-33 AB position.
I-4

MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION
101 A5A303C720 CABINET,FRONT ASS'Y
102 85OP700037 HOLDER,LED
103 752WSA0230 SHIELD,CASE HEAD AMP
104 753WSA0118 PLATE,EARTH-SYSCON
105 899HV3T000 HOLDER,ANODE WIRE
106 702WPA0832 CABINET,BACK
107 761WPA0225 HOLDER,DECK
108 735WPAA267 BUTTON,REC
109 753WUAA006 SPRING,EARTH HEAD AMP
110 726000A023 SHEET,CRT SERVICEMAN

111 741WUA0019 SPRING,EARTH
112 85OP700038 HOLDER,END SENSOR
113 701WPJB518 CABINET,FRONT
114 722552A016 SHEET,RATING
115 711WPA0114 PLATE,FRONT
116 712WPJB272 FLAP
117 713WPA0075 GUIDE,REMOCON
118 7230006830 SHEET,LED
119 752WSAA040 PLATE,DECK SHIELD
120 723000A823 FILM,DECORATION

121 735WPDA523 BUTTON,FRAME
122 743WKA0032 SPRING,FLAP(COMBO)
123 7220001119 SHEET,CSA WARNING
124 755WPA0026 PLATE,COVER LIGHT
125 722000A023 SHEET,HWC
201 8117540B04 SCREW,TAPPING(B0) TRUSS 4x20

202 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16
203 8107630604 SCREW,TAP TITE(S) BRAZIER 3x6
204 8110630A24 SCREW,TAP TITE(P) BRAZIER 3x12
205 8121F50B84 SCREW,TAPPING(B0) FAI20 FLAT 5x28
206 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
207 8110630804 SCREW,TAP TITE(P) BRAZIER 3x8
208 8109I30804 SCREW,TAP TITE(B) WH7 3x8
209 8110330804 SCREW,TAP TITE(P) FLAT 3x8
210 8109630802 SCREW,TAP TITE(B) BRAZIER 3x8

211 8109I30A04 SCREW,TAP TITE(B) WH7 3x10
--- 791WHAA016 LAMIFILM BAG

--- A5A303C975 INSTRUCTION BOOK KIT
--- 792WHA0271 PACKAGE,TOP
--- 792WHA0272 PACKAGE,BOTTOM
--- 793WCDA975 GIFT BOX
--- JA5K0100 POLY BAG
--- J5A30301 INSTRUCTION BOOK
J1-1

CHASSIS REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
300 A5A305A420K DECK ASSY A5A305A420K 501 8107226804 SCREW,TAP TITE(S) BIND 2.6x8
502 810A123504 SEMS A M2.3x5.0
301 85OA400227 PINCH ROLLER BLOCK 503 8107226404 SCREW,TAP TITE(S) BIND 2.6x4
302 85OA500026 AHC ASS'Y 504 8102120604 SCREW,PAN M2x6
303 85OP200290 BELT,CAPSTAN (S) 505 8109126604 SCREW,TAP TITE(B) PAN 2.6x6
304 85OP600581 WORM 506 810A130404 SCREW/WASHER(A) M3x4
305 85OP500083 BASE,AC HEAD 507 810A126504 SCREW/WASHER(A) M2.6x5
306 85OP800324 SPRING,AC HEAD 508 82Q264713N POLYSLIDER WASHER 2.6x4.7xT0.13
307 85OA000459 MAIN CHASSIS ASS'Y 509 82P184505N POLYSLIDER WASHER(CUT) 1.8x4.5xT0.5
308 85OA200089 CLUTCH ASS'Y
309 85OA200090 ARM IDLER ASS'Y 510 83ETW30000 E-RING 3
310 85OA300065 LOADING ARM S UNIT CD1501 122H071603 CORD JUMPER SMCD-7X151
311 85OA300066 LOADING ARM T UNIT CD1502 122Y021902 CORD JUMPER 2Y021902
312 85OA400223 INCLINED BASE T UINT 3S H5001 1523D91034 HEAD (AUDIO CONTROL) HVMXA1072A
313 85OA400232 P5 ARM ASS'Y 2 H5002 1543D02013 HEAD (FULL ERASE) HVFHP0032A
314 85OA400233 TENSION ARM ASS'Y (WT) ! M101 1596P98001 MOTOR (LOADING) MXN13FB12K3
315 85OA400231 INCLINED BASE S UNIT ! M2001 1510S98036 CAPSTAN DD UNIT F2QVB08
316 85OP800358 SPRING,LOCKER ! M2003 1589S11014 MICRO MOTOR I2OAL03
317 85OP900736 CASS,HOLDER ! UN4001 A5A305A500 CYLINDER UNIT ASS'Y A5A305A500
318 85OP900748 CASS,SIDE L
319 85OP900749 CASS,SIDE R
320 85OP900739 LOCKER,R

321 85OA900228 LINK UNIT
322 85OP000496 POST,CASS GUIDE
323 85OP200291 REEL,S (S)
324 85OP200292 REEL,T (S)
325 85OP200308 GEAR,IDLER
326 85OP200311 GEAR,CLUTCH
327 85OP200312 GEAR,COUPLING
328 85OP200313 LEVER,CLUTCH
329 85OP300194 GEAR,MAIN LOADING
330 85OP400490 LEVER,TENSION

331 85OP400492 HOLDER,TENSION
332 85OP400520 CAP.P4
333 85OP400532 BAND,TENSION
334 85OP400533 CONNECT,TENSION
335 85OP600573 ARM,BRAKE T
336 85OP600574 BAND,BRAKE T
337 85OP600577 CAM,PINCH ROLLER
338 85OP600578 CAM,MAIN
339 85OP600579 ROD,MAIN
340 85OP600582 GEAR,JOINT

341 85OP800322 SPRING,TENSION
342 85OP800350 SPRING,BRAKE T
343 85OP800355 SPRING,COUPLING
344 85OP800356 SPRING,RING
345 85OP900750 LEVER,LINK 2
346 85OP900744 LEVER,FLAP
347 85OP900745 CASS,OPENER
348 85OP900746 BRACKET,TOP 3V
J2-1

RESISTORS DIODES
! R415 R002T22R2J RC 2.2 OHM 1/2W D536 D28TELS6N6 DIODE RECTIFIER 10ELS6N-TA1B2
! R420 R801R7822F RC 8.2K OHM 1/10W D537 D1VT001330 DIODE,SILICON 1SS133T-77
! R439 R801R7223F RC 22K OHM 1/10W D601 D1VT001330 DIODE,SILICON 1SS133T-77
! R442 R801R7153F RC 15K OHM 1/10W D602 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
! R444 R801R7183F RC 18K OHM 1/10W D605 D2WT11ES10 DIODE SILICON 11ES1-EIC
! R447 R65582680J R,FUSE 68 OHM 1/2W D608 D2WXSB1400 DIODE SCHOTTKY SB140-EIC
R449 R63502010J R,FUSE 1 OHM 1/2W or D609 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
R655U2010J R,FUSE 1 OHM 1/2W D610 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
! R450 R655815R6J R,FUSE 5.6 OHM 1W D611 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
! R500 R0G3K2275K RC 2.7M OHM 1/2W D612 D1VT001330 DIODE,SILICON 1SS133T-77
! R501 R5Y2CD2R2J R,CEMENT 2.2 OHM 5W D613 D1VT001330 DIODE,SILICON 1SS133T-77
! R502 R3X28B100J R,METAL OXIDE 10 OHM 3W D614 D1VT001330 DIODE,SILICON 1SS133T-77
! R510 R903N8105J RC 1M OHM 1/8W D615 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
! R512 R002T2563J RC 56K OHM 1/2W D619 D1VT001330 DIODE,SILICON 1SS133T-77
R514 R3X181R33J R,METAL OXIDE 0.33 OHM 1W D620 D1VT001330 DIODE,SILICON 1SS133T-77
! R517 R3X181331J R,METAL OXIDE 330 OHM 1W D621 D1VT001330 DIODE,SILICON 1SS133T-77
! R528 R63581R22J R,FUSE 0.22 OHM 1W D791 0021E2Q150 LED LTL-4224-031A
! R802 R3X181123J R,METAL OXIDE 12K OHM 1W D793 0021E2Q150 LED LTL-4224-031A
! R805 R3X181123J R,METAL OXIDE 12K OHM 1W D1001 D1VT001330 DIODE,SILICON 1SS133T-77
! R810 R3X181123J R,METAL OXIDE 12K OHM 1W D1003 0010100320 INFRARED LED LNA2702L010R
CAPACITORS D4003 D1VT001330 DIODE,SILICON 1SS133T-77
C354 E02L02222M CE 2200 UF 16V ICS
! C402 E02L04102M CE 1000 UF 35V ! IC351 I01DP75110 IC AN7511
! C407 E02L03102M CE 1000 UF 25V ! IC401 I01TD55220 IC AN5522
C423 P4J7F3474J CMPP 0.47 UF 250V PMS IC501 I1KA98R050 IC KIA78R05PI
! C424 P4N8FJ912H CMPP 0.0091UF 1.25KV ! IC502 0002500450 PHOTO COUPLER TLP621(GR)
! C431 E02LTD2R2M CE 2.2 UF 250V IC601 I06FC61206 IC M61206FP
! C433 E02LT3331M CE 330 UF 25V IC1001 I56F57071A IC OEC7071A
C451 P61101224J CMPL 0.22 UF 100V TF or ! IC1003 IC7J0311A0 IC R3111N311A/C-TR
P611T1224J CMPL 0.22 UF 100V TF IC1099 A5A304C015 IC S-24C04BDP-LA
! C506 P2472B224M CMP 0.22UF 275V PHE840 IC4001 I03F301MN0 IC LA71201M-N-MPB
! C507 C0JTB0513K CC 0.001 UF 500V B TRANSISTORS
C509 E51CGC471M CE 470 UF 200V Q403 TNAAJ05003 COMPOUND TRANSISTOR KRC111SRTK
! C511 E02LT3471M CE 470 UF 25V Q404 TPAAD05003 COMPOUND TRANSISTOR KRA104SRTK
C517 C03L0R7H3K CC 0.0022UF 2KV R ! Q405 TC5T01627Y TRANSISTOR SILICON 2SC1627_Y(TPE2)
! C521 E62NFC221M CE 220 UF 200V ! Q406 TD30026270 TRANSISTOR SILICON 2SD2627LS-CBC11
! C530 CB3930MQ2K CC 470 PF 250V Q407 T8YJ2412K0 TRANSISTOR SILICON 2SC2412KT146 R,S
C535 C03L0R713K CC 0.001 UF 2KV R Q505 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S
! C539 CB3930ML3M CC 0.0033UF 250V Q507 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
C541 C03L0R7W2K CC 820 PF 2KV R ! Q510 TJXG5NC500 FET STP5NC50FP
C801 C0PWB07H3K CC 0.0022UF 2KV B ! Q511 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
DIODES Q601 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S
D401 D2WT011E10 DIODE SILICON 11E1-EIC Q602 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
! D402 D2WXN49370 DIODE SILICON 1N4937 Q603 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
D403 D97U03001B DIODE,ZENER MTZJ30B T-77 or Q604 TDWT00400E TRANSISTOR SILICON 2SD400E
D97U03301C DIODE,ZENER MTZJ33C T-77 Q605 TDWT00400E TRANSISTOR SILICON 2SD400E
D404 D97U03001B DIODE,ZENER MTZJ30B T-77 or Q606 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
D97U03301C DIODE,ZENER MTZJ33C T-77 Q608 TNAAJ05003 COMPOUND TRANSISTOR KRC111SRTK
D405 D2WT011E10 DIODE SILICON 11E1-EIC Q609 TNAAJ05003 COMPOUND TRANSISTOR KRC111SRTK
D407 D1VT001330 DIODE,SILICON 1SS133T-77 Q611 TNAAB05003 COMPOUND TRANSISTOR KRC102SRTK
! D408 D94TA27011 DIODE ZENER HZ27-1L TD Q612 TNAAB05003 COMPOUND TRANSISTOR KRC102SRTK
! D409 D94TA11B13 DIODE ZENER HZ11B3L TD ! Q804 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
D410 D97U06R81B DIODE,ZENER MTZJ6.8B T-77 ! Q805 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
D411 D1VT001330 DIODE,SILICON 1SS133T-77 ! Q806 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! D412 D2WXN49370 DIODE SILICON 1N4937 Q1003 0002700530 PHOTO COUPLER RPI-352Q01R
! D413 D2WXN49370 DIODE SILICON 1N4937 Q1004 TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK
! D501 D97U01001B DIODE,ZENER MTZJ10B T-77 ! Q1005 0002700590 PHOTO COUPLER RPI-301
! D505 D2WXB290S0 DIODE SILICON SB290S Q1007 TNAAB05003 COMPOUND TRANSISTOR KRC102SRTK
D507 D2W0B290S0 DIODE SILICON SB290S-B-EIC or Q1008 TNAAB05003 COMPOUND TRANSISTOR KRC102SRTK
D2WXB290S0 DIODE SILICON SB290S Q1009 0002700530 PHOTO COUPLER RPI-352Q01R
D508 D1VT001330 DIODE,SILICON 1SS133T-77 Q1011 0000M00390 PHOTO TRANSISTOR ST-304L
! D510 D2WXRU2AM0 DIODE SILICON RU2AM-EIC Q1013 0000M00390 PHOTO TRANSISTOR ST-304L
! D512 D2WXB290S0 DIODE SILICON SB290S Q1023 T8YJ2412K0 TRANSISTOR SILICON 2SC2412KT146 R,S
D513 D1VT001330 DIODE,SILICON 1SS133T-77 Q1024 TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK
D514 D1VT001330 DIODE,SILICON 1SS133T-77 Q4001 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! D515 D97U03301B DIODE,ZENER MTZJ33B T-77 or Q4002 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
D97X03301B DIODE,ZENER MTZJ-33B-T72 Q4003 TPAAC05002 COMPOUND TRANSISTOR KRA103SRTK
! D517 D28TELS2N2 DIODE RECTIFIER 10ELS2N-TA1B2 Q4005 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)
D518 D2WTRM11C0 DIODE SILICON RM11C-EIC Q4006 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT
! D519 D2WXB290S0 DIODE SILICON SB290S Q4007 T8YJ2412K0 TRANSISTOR SILICON 2SC2412KT146 R,S
D520 D2WTRM11C0 DIODE SILICON RM11C-EIC Q4009 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S
D521 D2WTRM11C0 DIODE SILICON RM11C-EIC Q4010 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S
D528 D97U05R61B DIODE,ZENER MTZJ5.6B T-77 Q4011 T8YJ2412K0 TRANSISTOR SILICON 2SC2412KT146 R,S
D530 D2WTRM11C0 DIODE SILICON RM11C-EIC Q4012 T8YJ2412K0 TRANSISTOR SILICON 2SC2412KT146 R,S
D533 D1VT001330 DIODE,SILICON 1SS133T-77 COILS &TRANSFORMERS
! D534 D97U01801B DIODE,ZENER MTZJ18B T-77 L401 021679472K COIL 4.7 MH
! D535 D97U01801B DIODE,ZENER MTZJ18B T-77 ! L502 029T000092 COIL,LINE FILTER 1R0A103F24
J3-1

COILS &TRANSFORMERS MISCELLANEOUS
! L503 028R140031 COIL,DEGAUSS 8R140031 ! F502 081PC2R504 FUSE 51MS025LCC
L601 0331920018 COIL 3192001 ! FB401 043213015R TRANSFORMER,FLYBACK 3213015R
L603 02167F470J COIL 47 UH FH501 06710T0006 HOLDER,FUSE EYF-52BC
L607 021LA6220K COIL 22 UH FH502 06710T0006 HOLDER,FUSE EYF-52BC
L612 021LA66R8K COIL 6.8 UH FH503 06710T0006 HOLDER,FUSE EYF-52BC
L801 021673221K COIL 220 UH FH504 06710T0006 HOLDER,FUSE EYF-52BC
L1001 021LA62R2K COIL 2.2 UH OS753 077Q037002 REMOTE RECEIVER PIC-37143TH5
L1003 02167H220K COIL 22 UH ! SP351 070C533019 SPEAKER SG04D11BNA or
L4001 02167F220J COIL 22 UH 070W535002 SPEAKER NF-16D27W
L4003 02167F101J COIL 100 UH ! TH501 DF5EL3R0A0 DEGAUSS ELEMENT ZPB45BL3R0A
L4005 02167F470J COIL 47 UH TM101 076R0CG010 TRANSMITTER R25-1195 or
L4006 02167F470J COIL 47 UH 076N0CG010 TRANSMITTER RC-CG010
L4009 02167F101J COIL 100 UH ! TU601 0145K00055 TUNER,VHF-UHF TECC1040PG32D
T401 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ ! V801 098Y1404B9 CRT W/DY A34JXV70X53N45
! T501 0481290804 TRANSFORMER,SWITCHING 81290804 X602 100CT3R505 CRYSTAL HC-49/C 3.579545MHz
T4001 031626009R COIL,BIAS OSC 1626009 X1001 100CT01207 CRYSTAL HC-49/U-S 12MHz
JACKS X1002 100DA32R01 CRYSTAL DT-26 32.768KHz
! J351 060G131014 RCA JACK HTJ-035-28A X4001 100CT3R502 CRYSTAL HC-49/U 3.579545MHz
J701 060Q401075 RCA JACK AV2-24D-5
! J801 066X120014 SOCKET,CRT HPS3200-010501 RESISTOR
SWITCHES RC................... CARBON RESISTOR
SW751 0504101T34 SWITCH,TACT EVQ21505R
SW791 0504101T34 SWITCH,TACT EVQ21505R CAPACITORS
SW792 0504101T34 SWITCH,TACT EVQ21505R CC................... CERAMIC CAPACITOR
SW793 0504101T34 SWITCH,TACT EVQ21505R CE................... ALUMI ELECTROLYTIC CAPACITOR
SW794 0504101T34 SWITCH,TACT EVQ21505R CP................... POLYESTER CAPACITOR
SW795 0504101T34 SWITCH,TACT EVQ21505R CPP.................. POLYPROPYLENE CAPACITOR
SW796 0504101T34 SWITCH,TACT EVQ21505R CPL.................. PLASTIC CAPACITOR
SW797 0504101T34 SWITCH,TACT EVQ21505R CMP.................. METAL POLYESTER CAPACITOR
SW798 0504101T34 SWITCH,TACT EVQ21505R CMPL................ METAL PLASTIC CAPACITOR
SW799 0504101T34 SWITCH,TACT EVQ21505R CMPP............... METAL POLYPROPYLENE CAPACITOR
SW1001 0508A11002 SWITCH(LEAF) MXS01380MPP0
VARIABLE RESISTORS
VR401 V1263H3BT7 VOLUME,SEMI FIXED RH0683CJ3R
VR502 V1163L2BTC VOLUME,SEMI FIXED EVNCYAA03BY2
P.C.BOARD ASSEMBLIES
PCB010 A5A303C010 PCB ASS'Y VMA227A
PCB030 A5A303C030 PCB ASS'Y TEXA28A
PCB110 A5A303C110 PCB ASS'Y TCA377A
MISCELLANEOUS
ANT001 125C108027 ANTENNA ROD T4-216BNK-BK
B402 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B501 024A8407C3 CORE,BEADS BL02RN2-R62T2
B604 024HT03564 CORE,BEADS W4BRH3.5X6X1
CD351 06CH27090A CORD CONNECTOR CH27090A
CD352 06CH12435A CORD CONNECTOR CH12435A
! CD501 120R414903 CORD AC BUSH 0R414903
CD757 06CH2A019A CORD CONNECTOR CH2A019A
CD801 06CU82039A CORD CONNECTOR SM1098-009-1A
CD803 06CH012101 CORD CONNECTOR CH012101
CD851 WHL6032038 FLAT CABLE AWG26 10C BLACK 320MM
CD852 06CH01408A CORD EIS CONNECTOR CH01408A
CF601 1022045R72 FILTER,SAW SAFGP45M7VFYZR0B or
1022T45R72 FILTER,SAW SAF45MFY220ZR
CF603 1011T4R504 FILTER,CERAMIC EFCT4R5YS5A
CF604 1011T4R517 FILTER,CERAMIC EFCT4R5MW5
CP351 0694260139 CONNECTOR PCB SIDE 173979-6
! CP401 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
! CP502 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP504 069W01001A CONNECTOR PCB SIDE 003P-2100
CP505 069W01001A CONNECTOR PCB SIDE 003P-2100
CP757 06942A0139 CONNECTOR PCB SIDE 1-173979-0
CP801 069S320010 CONNECTOR PCB SIDE A2361WV2-2P
CD4001 122L061501 CORD JUMPER 2L061501
CP1001 06972C0010 CONNECTOR PCB SIDE TMC-J12P-B2
CP4001 0697240600 CONNECTOR PCB SIDE TOC-C04X-B1
CP4002 069J760029 CONNECTOR PCB SIDE IMSA-9604S-06Z14
CP4003 0697120320 CONNECTOR PCB SIDE TMC-T02X-E1
CP851A 067U010049 WIRE HOLDER B2013H02-10P
CP851B 067U010049 WIRE HOLDER B2013H02-10P
CUS012 800WFAA008 CUSHION C
! F501 081PC05004 FUSE 51MS050LCC
J3-2

SPEC.NO. M5A3-03C
O/R NO. K1Y5017

A B C D E F G H
Y/C/AUDIO/CCD/HEAD AMP SCHEMATIC DIAGRAM

8
(SYSCON PCB) 8
VCR_A_MUTE
H.AMP_SW1
H.SW
ENV_DET
P.CON+5V
P.CON+5V
Y/C_DATA
Y/C_CS
Y/C_CLK
R4044
BUFFER
L4005
100K
47uH
0305
Q4012
2SC2412K
R4041 5.0
4.0
R4047
R4045
L4006
12K
47uH
0305
12K
1.8K
3.4
6.3V 47 KA
2
FROM TV POWER
7 7
C4063
R4054
18K
0.01 F
R4043
C4060
3.3K
P.CON+5V
GND
50V 1 KA
50V 1 KA
C4062
C4065
W858
C4069
FROM/TO IN/OUT
0.1 F
NC C4058
R4051
0.022 B
2.7K
C4064
FRONT_AUDIO
0.022 B
6.3V 47 KA
C4066
C4059 FRONT_VIDEO
KA
R4039
8.2K Y/C_AUDIO
R4042
C4067
820
0.1 F
50V 1
Y/C_VIDEO
R4038 C4061
680K 0.01 F
100CT3R502
FROM/TO MICON
X4001
W818
6 Y/C_CLK 6
Y/C_DATA
NC
0.5 2.8 0 0 0 4.8 4.8 4.8 5.0 1.9 2.6 4.0 3.3 3.3 2.3 5.0 5.0 0 2.2 0.8 Y/C_CS
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
V.REC_ST_H
C4016 2.2 COMPOUT ENV ALWAYS VDD 4Fsc CLOCK
AUDIO C-ROT C-GND C-VCC 0 BUFFER VCR_A_MUTE
61
40
KILL DET MUTE RF-SW SERAIL 320FH 5V VSS
VX01 SLD B PLL Q4010
0.068 B DET HA SW IN DECODER VCO
0 2SA1037AK DUMMY_V.SYNC
HA 1.7
R4033
P R
62
39
2.2K
TIMMING OUT 1.7 CTL-
GND OUT
C4019 4.0 REC PB REC 0 CTL+
63
CHROMA
38
APC APC AFC DRIVER AUTO-BIAS
DET 0 2.3 H.AMP_SW1
0.047 F VSS
C4015 1.8 ACC 3.0 R4034
ENV_DET
64
37
DET BEFORE
CCD CLAMP
R P BGA IN
0.047 F C4048 82K H.SW
0.7 BGA 2.8 R4035
AFTER
65
36
NC P CNC SD_VIDEO
BGA 16V 10 KA C4052 100K
5 0.7 R P VCA 3.1 SD_SYNC 5
66
NC R PB VCA 35
H
P R
3.58M
AMP C4049 50V 4.7 KA PLAY_LED
0.7 3.1
P BPF2 R4062
67
34
L
NC CLAMP
B.D 3.3M
L4001 Main B-UP 16V 10 KA
5.0 C-LPF
CONV P 2.6
P.CON+5V AMP
68
33
HA VCC VCP
16V 47 KA
22uH C4053
R4064 1.7 ACC 3.58M C4057
1 F
C4009
2.0
C4055
0305 BPF1 50V 4.7 KA TU_VIDEO

69
32
P AMP R 1
2
6.8K R4012 + 3 1 F
820 1.8 PB-C 4.0 C4054
ACC REG
70
31
4.21M DET 4V
VIDEO
BPF
AGC 0.1 F C4047
0 HA YNR/COMB
NC FRONT_VIDEO
71
30
PRE GND Sub P R R 2.0

CONV P 16V 10 KA
2.0 R 1/2 BAL 2.3 C4050
DETAIL N.L. L4009
72
29
CLAMP
FROM/TO MICRO MOTOR P H ENH P DEEM
PB-C FBC TC1 R4048
L 0.22 B P.CON+5V
2.0 Y-LPF R 2.3
100 KA
CP4001_1 NL NL Y/C
73
28
C4041
C4042
R NC1 68 1/4W 100uH
0.1 F
P
6.3V
4 TOC-C04X-B1
EMPHA EMPHA R MIX R R4060 1.5M
0305 4
2.0 P
AGC 1.6
74
27
P
4 SP-CH1 (R) FM TC2
MOD C4051 1
3 SP COM 0 2.9 6.3V 33 KA R4032 R1025
R-EQ Y/C_VIDEO
75
26
NORMAL
A-GND TEST QV/QH 6DB
2 SP-CH2 (L) R4052 DOUBBLE FM SUB
LIM DEM LPF 100 1/4W 100
R4007 8.2K C4020 2.2 3.6
1 NC TU_AUDIO SYNC SD_VIDEO
76
25
1
2 ALC R LINE SEP
39K 1/4W 0.1 F 3 LPF REC
MAIN
R4004 4.9 P AMP FM-EQ 0
P.CON+5V DE-EM V.SYNC DUMMY_V.SYNC
77
24
A-VCC
SEP
15 1/4W
R4006 C4021 ALC FM PB 4.9 W888
FRONT_AUDIO 2.3 DET VREF FM EQ S-EQ P.CON+5V
78
23
P R AGC P R P R Y-VCC FROM/TO CHROMA/IF

R4068
2.2M
C4012 R4053 NC VHS SOPB

47K 1/4W 0.1 F REC C4046
6.8K C4023 0 PB,EE MUTE 2.8 5.0
PB,EE AMP TU_VIDEO
79
22
0 BUFFER
6.3V 22 KA EQ 50V 3.3 KA
4.7K
6.3V 22 KA REC:LP<EP Q4009 TU_AUDIO

2.0 AMP 1.8
PB:EP AUTO PHASE PHASE FM MAIN
2SA1037AK
80
21
Vref SP,LP BIAS EQ EQ AGC EMPHA S B

SD_VIDEO
5.0
6.3V 220 KA
fo-ADJ Q-ADJ Y-GND DET

2.3V FIL FIL
3 3
C4044
C4045
Y/C_AUDIO
0.1 F
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Y/C/A/CCD/H.AMP IC
47K 1/4W
0 1.5 0.1 2.2 VD

IC4001 2.2 2.2 2.3 2.2 2.2 2.5 2.3 2.2 2.3 2.4 5.0 1.0 1.0 1.7 1.4 0 NC
R4028
0.0033 B
33 KA R4055 C4028
0.1 F
LA71201M-N-MPB
C4032
R4022
3
470
33K
R4023
FROM/TO HEAD AUDIO CONTROL R4026 C4043

390P B
C4036
0.01 F
C4074
P.CON+5V SD_SYNC
1K
NC
CP4002 R4021 39K 0.1 F
KA
5.2 R4029 2.8

V.ENV
R4025
IMSA-9604S-06Z14 SW 0.7
1.5K
0
C4034
V.REC_ST_H Q4003 22K TP4001

25V 4.7
W887
C4027
6 AUDIO PB KRA103SRTK 47K 1/4W

R4018 R4017
C4033 0 RECORD COLOR SIGNAL

6.8K
5.3 COIL,BIAS OSC SYNC IN

C4037
5 AUDIO REC C4025_1

0.1 F
T4001 Q4007
6.3V
CTL+ BIAS CTL 820P B

PLAYBACK LUMINANCE SIGNAL
KA
4 CTL+ 1626009 2SC2412K

50V 1 KA
R4024
Q4005
8.2K
5.6K
180P CH
18P CH
C4031
CTL- 6.3V 220 KA 4

C4024_1
C4038
3 CTL- 6 1 L4003
C4035
KTA1266
PLAYBACK VIDEO SIGNAL
50V 3.3
R4001 R4019
2 AE HEAD(-) 5 2
0 5.2
1 AE HEAD(+)
560
4 3
100uH 330K AUDIO SIGNAL(REC)
2 0305 2
0.01 F
0 5.2 C4029
AUDIO SIGNAL(PB)
R4010
C4005
0.1 F
C4076
3.3K
AUDIO R4011 W873

R4057
0.7 R4002 5 0
6.8K
PB SW BIAS OSC 0.01 F BUFFER

TUNER VIDEO SIGNAL
220 KA
W880
16V 10 KA
MKT
Q4001 10K Q4006 22K Q4011

C4004
C4030
KTC3198 0 0 2SC2412K
0 KTC3203_Y RECORD LUMINANCE SIGNAL
1SS133
4.9
D4003
C4010 R4059
1/4W
0.6
100V 0.022
C4014_1
0.047 B
AUDIO
C4002
R4056
RECORD COLOR SIGNAL
R4037
6.3V
TO FULL ERASE HEAD PB SW 0 6.3V 47 KA 4.7M 10M

R4016
390
R4003 0
0.015 B
Q4002 0.7
R4020
R4015
150P CH
C4006
2.2M
470K 1/4W
150
CP4003
C4075
2.2
KTC3198
R4058
2.7K
R4014
TMC-T02X-E1 10K
R4061
10M
0 PCB010
GND
2 FE HEAD(GND)
W897 VMA227
HOT
1 FE HEAD(HOT)
VCR_A_MUTE
Y/C_AUDIO
PLAY_LED

P.CON+5V
1 1
VD
NOTE: THE DC VOLTAGE AT EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
DURING PLAYBACK
A B C D E F G H
G-1 G-2

A B C D E F G H
FROM TV POWER MICON SCHEMATIC DIAGRAM (SYSCON PCB)

POWER_FAIL2
SERVICE
8 TP1001 R1032 10K 8
C1056
P.CON+5V 0.1 F NC
SD_SYNC
OSD_R
OSD_G
OSD_BLK
OSD_B
CENTLED
100P CH
CAP_CTL
REEL_S
22K 1/4W CYL_DRIVE
REEL_T
Y/C_DATA
V.REC_ST_H
SDA
Y/C_CS
Y/C_CLK
SCL
C1071
GND
0.1 F
C1065
C1028
0.1 F
100P CH
MOTOR+12V
C1034
R1007
R1035
22
10
GND
R1036 4.7K
0.1 F
R1031
100P CH
C1061 100P CH
C1060
C1004
1K
0.0068 B
R1029
R1028
R1021
C1029
10
4.7K FROM/TO Y/C/AUDIO/HEAD AMP
R1063
4.7K
C1035
7 6 Y/C_CLK
R1042
C1009 220P CH
C1010 220P CH
C1023 220P CH
C1037 390P CH
220
220P CH
Y/C_DATA
C1031
R1044 Y/C_CS
7 7
39K
22K
220
W810
0.001 B H.SW
5.6K R1033 C1062
C1001 5.9 SD_VIDEO
220 YK
R1038
X_RAY 0.2
220
X_RAY_SW 1K 1 B
R1053
R1017
R1020
ENV_DET
C1032
16V 47 YK Q1023 R1078

C1089
FROM/TO DECK
0.1 F
R1045
R1075
4.7K
0 2SC2412K VCR_A_MUTE
C1007 390K
16V
CP1001 (CP101) 5.6K CTL+
680P CH
TMC-J12P-B2
R1034
C1038
25V 47 YK CTL-
1M
L1003 CAP_FG NC
1 CAP_FG 0.9 0.9 0 1.8 2.5 NC 0 4.9 2.5 2.6 0 0 4.7 0 0 0 0 0 0 4.8 0 4.9 4.2 0 2.3 1.6 2.1 5.2 0 5.2 DUMMY_V.SYNC
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
2 CAP_VCO V.REC_ST_H
DRUM-PWM
CAP-PWM
22uH ELC0607 VCR_A_MUTE TAB_SW

75 VOLUME
55 VHOLD
52 SD-IN(MONI)
66 V REC START H
SERVICE
57 NUA
68 SDATA
53 OSD-VCC
81
50
REEL-S
60 OSD OUT1
CAP FULL
REEL-T
70 SCLK
67 NC
65 NC
59 V-SYNC
74 JUST CLOCK
61 CENTER LED
3 VCC 69 CS
64 R
63 G
H.AMP_SW1
62 B
54 HLF
58 H/C-SYNC
56 CVIN
73 FF/REW-L
72 IIC-DATA1
R1010
71 IIC-CLK1
CAP_M/F/R 0 5.2
4 CAP_M/F/R TV_A_MUTE SD_SYNC
82
49
3.3K 1/4W 5.1 0
5 I_LIMIT PLAY_LED
83
48
NC NC
6 GND[M]
6 6
84
47
7 GND NC NC (AV1) NC
R1001
8 LD/CY_VCO
85
46
POWER_FAIL_L NUB
CAP_CTL 5.9 0
9 CAP_CTL 3.3K C1046 20P CH
W805 IIC_OFF 81 VCR_A_MUTE
86
45
LDM_CTL IIC OFF 50 TAB SW OSC-OUT2
10 LDM_CTL 5.2 2.6 L1001 R1005
R1008 11
CAP_FG 82 TV_A_MUTE 2.2uH 2.7K
87
44
11 CYL_FG/PG CAP-FG 49 OSD-VSS OSC-IN2
C1013 2.5 2.5
CYL_DRIVE 1K 1/4W R1040 C1047 18P CH
12 CYL_CTL 0.0039 B 83 (EXT MUTE)
88
43
AMP-VSS 48 (AV2) CLKSEL
R1048 0 5.2 FROM/TO CHROMA/IF
33K
89
42
NC NC NC
R1064 4.7K 2.0
13 POWER_OFF_H
X-RAY_TEST
90
41
FROM/TO DECK DRUM FG/PG X-RAY_TEST
0.6 0 HD
1K 1/4W C1015 10V 47 KA
0.0047 B
91
40
AMP-VREFOUT VD
C1084
VSS
2.5 0 8 C1040 18P CH
C1016 16V 22 KA AFT_M
92
39
AMP-VREFIN X-OUT(12MHz)
CD852 2.5 2.6 X1001
BOT
EOT
C1018 50V 4.7 KA C1048 18P CH SCL

CH01408A 98 AMP-VCC 100CT01207
93
38
5 C X-IN(12MHz)
SDA 5
0.2 2.1
CTL- R1009 560 33 PLAY LED
99 ANALOG VCC
94
37
CTL- VCC OSD_R
R1012 C1019 0 32 RENT_H 5.2 C1026
CENTLED R1013 560 C1049 22P CH
CTL+ 10K 0.001 CH 100 DEW 0.01 F OSD_G
95
36
CTL+ 31 ON-TIMER LED XC_OUT(32KHz)
2.5 1.3 X1002
C1020 OSD_B
100DA32R01
96
35
BOT SENSOR AMP C XC_IN(32KHz)
3.9 FF/REW_SW C1027 2.6 1.5 OSD_BLK
Q1011 C1022 16V 10 KA C1050 20P CH
R1073
330K
EOT SENSOR Q1004 0 0.0039 B RESET

97
34
13 DUMMY-V.SYNC
CTL AMP-OUT RESET-L AT+5V_BACKUP

15 COLOR ROTARY
ST-304L S825Y
16 HEAD.AMP.SW
Q1013 KRC103SRTK 2.5 5.2

17 ENV-CMP-IN
0.1 F
14 REMOCON-IN
22 DEGAUSS_H
18 VIDEO-H.SW
24 H_CONTROL
0 ST-304L 10 PLAY_LED AT+5V

6 VIDEO-ENV
98
33
19 HI-FI-H.SW
7 AFT(MONI)
12 CAP-LIMIT
5.1
5 HI-FI-ENV
VCR-POWER
11 CAP-FWD
8 AFT(REC)
25 PROTECT
20 LDM CTL
5.1 4.8 VCR_POWER_H

EXT-MUTE
TV-POWER
0
T-REC LED
R1011
330K
MSSEN-A
MSSEN-B
0.1 REC LED NC

100 99
32
9 KEY 1
10 KEY 2
C1025 5.2 0 TV_POWER_H

21 NC
23 NC
0.0022 B
BOT
EOT
31 NC PROTECT
5.0
0 0
C1042_2 TIMER SYSCON MICON IC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
D1003
R1018
47K
LNA2702L010R IC1001 1.4 1.4 0 0 0 2.4 2.2 0 5.2 5.2 0 2.2 0 0 0 5.2 2.3 2.6 2.6 0 0 5.2 5.2 0 0
5.0 5.2 NC
1/4W
1 F OEC7071A NC NC TV_POWER_H
NC
4 TAB_SW VCR_POWER_H 4
R1066
270 1/4W
4.7K
C1068
MXS01380MPP0
C1043
R1016
0.0022 B FROM/TO IN/OUT

R1055
H.SW 9
SW1001
4.7K
0.01 B
0
R1070 IIC_OFF
5.1 H.AMP_SW1 H.SW 2.5 2.6 0 5.2
LED DRIVER TP1002 REC_LED
100 5 6 7 8
Q1024 0 NC T-REC_LED
R1022 4.7K
VCC
KRC103SRTK
TEST
S-24C04BDP-LA
SDA
KEY_A
SCL
R1054
EEP ROM IC
4.7K
IC1099 KEY_B
CAP_M/F/R REMOCON_IN
DUMMY_V.SYNC
W894 SCL
VSS
A2
A1
A0
REMOCON_IN
SDA
0.0022 B
LDM_CTL
MS_SEN-A
MS_SEN-B
T-REC_LED
PROTECT
C1039_1
0.01 F
C1083
ENV_DET
REC_LED
W825
C1082
4 3 2 1
H_CTL
0.1 F
AFT_M
KEY_A
KEY_B
0 0 0 0
BOT
EOT
3 3
TO SOUND AMP
MS_SEN-A
MS_SEN-B
RESET
REEL_S
REEL_T
TV_POWER_H
6.3V 100 YK
TV_A_MUTE
C1058
FROM/TO DEFLECTION
X_RAY
R1047
R1030
R1046
X-RAY_TEST
4.7K
4.7K
4.7K
H_CTL
AT+5V
NC 0 NC
0
R1019
R1052
47K
390
5 4 R1049
SYSTEM RESET IC
MS_SEN A
R3111N311A/C
2 NC NC 2
18K 1/4W
Q1009 4.7K
IC1003
RPI-352Q01R
R1051
5.2 5.2 0.8 5.2 0 1.2

1 2
2 3 2 3 OUT IN GND
6.3V 220 YK
C1003_1
1 2 3 D1001
1 4 1 4 5.2 5.1 0
1SS133
0.8 1.4 0.5 1.4 4 3
MS_SEN B 0
25V 33 YK
0.9 PCB010
Q1003 REEL SENS
R1050
R1087
C1021
R1083
VMA227
33K
33K
C1017
100
0.1 F
RPI-352Q01R Q1005
RPI-301
S818Y
1 CAUTION: DIGITAL TRANSISTOR TUNER VIDEO SIGNAL 1
DEFLECTION SIGNAL
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE: THE DC VOLTAGE AT EACH PART WAS CAPSTAN AFC SIGNAL
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK CYLINDER AFC SIGNAL
CYLINDER APC SIGNAL
A B C D E F G H
G-3 G-4

A B C D E F G H
IN/OUT SCHEMATIC DIAGRAM

8 (SYSCON PCB) 8
(CD757) CP757_2
FROM/TO OPERATION
1-173979-0
(CD351) CP353_1
173979-7
REMOCON_IN 10
FROM/TO OPERATION
1
2
3
4
5
6
7
8
9
1
2
3
4
FRONT_AUDIO_IN 5
6
FRONT_VIDEO_IN 7
1
2
3
4
173979-4
173979-6
6
5
4
3
2
1
SOUND_GND
SOUND_OUT
TEST POINT
T-REC_LED
REC_LED
TEST POINT
AT+5V
SP_OUT
Y/C AUDIO
KEY_B
KEY_A
Y/C VIDEO
INT-MONI
GND
GND
AT+5V
GND
GND
B.OUT
GND
IIC OFF
SDA
SCL
CP1003
CP351_1
7 7
NC NC NC
C4206_1
0.0022 B
6 6
FROM/TO SOUND AMP
SOUND_GND
SOUND+
SP_OUT
W806
5 5
FROM CHROMA/IF
AT+5V
FROM/TO MICON INT-MONI
B.OUT
IIC_OFF
SDA
SCL
W903
T-REC_LED
(AI)
REC_LED
4 3.6 3.6 4
W912
0
(AI)
REC LED SW(AI) ON TIM/T-REC LED SW(TO)

Q1007 0
Q1008
0 KRC102SRTK 0 KRC102SRTK W866 FROM/TO TV POWER
GND
R4201
KEY_B
75
KEY_A
REMOCON_IN
3 3
FROM/TO Y/C/AUDIO/HEAD AMP
Y/C_AUDIO
Y/C_VIDEO
FRONT_AUDIO
2 FRONT_VIDEO 2
PCB010
CAUTION: DIGITAL TRANSISTOR B.SIGNAL VMA227
NOTE: THE DC VOLTAGE AT EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME TUNER VIDEO SIGNAL
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1 DURING PLAYBACK AUDIO SIGNAL(REC) 1
AUDIO SIGNAL(PB)
A B C D E F G H
G-5 G-6

A B C D E F G H
CHROMA/IF SCHEMATIC DIAGRAM (SYSCON PCB)

W829 11.0 8.2
8 FROM/TO MICON 8
REG.
PROTECT Q606
AT+5V 4.8 8.3 REG. 8.8
KTC3203_Y
AT+5V Q603
4.8 8.0 D608 KTC3203_Y
AT+5V_BACKUP 5.5
REG. REG.
VD SB140-EIC
Q602 REG.
0.01 F
Q605
C667
OSD_R KTC3203_Y 5.5 Q604 2SD400E
2SD400E
OSD_G 8.3 5.0
W801 5.0 8.3
OSD_B
5.6 5.6
R663
OSD_BLK
100
R616
W895
1K
R628
100
SDA
TU_VIDEO
SCL B604
CF604 FROM/TO Y/C/AUDIO HEAD.AMP
2.6 R620
AFT_M EFCT4R5MW5 W4BRH3.5X6X1 C648 R669
10V 1000 YK
1.9
7 SD_VIDEO 7
50V 22 YK
820 1/2W
L607
VCR_POWER_H 0
50V 22 YK
22uH
100
C641
50V 0.22 KA 470

TU_VIDEO
0.1 F
16V 47 YK
C640
R654
C644
HD BUFFER
C643
R610
R644
R668
Q601 TU_AUDIO
1/4W
1M
100
470
C652
POWER_OFF_H
R622
2SA1037AK W865
330
Y/C_AUDIO
VD
R615
120P CH
CF603
0.01 F
18P CH
C674
47P CH
C636
6.8uH
L612
R625
C654
R633
10K
C651
EFCT4R5YS5A
8.2K
470
TO IN/OUT
220P CH
50V 1 KA
L603
C673
47uH
0.015 B
R676
0305
INT-MONI
1K
C649
C650
INT-MONI C672
0.01 F R638 B.OUT
NC
8.2 8.2 4.0 NC 5.5 NC3.7 5.6
100CT3R505
2.0 2.0 8.2 0 0 3.2 3.2 2.0 AT+5V
8.8 8.2K
X602
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 R646
CHROMA APC FILTER

2.3
VIDEO/CHROMA GND
MCU RESET
INTELLIGENT MONI
R608 3.3
Y SW OUT
5.7V REG OUT(FOR CPU)
5v REG
6 C665 6
Hi Vcc
27K
TV/Y IN
49
32
C612 TO SOUND AMP
R612 10K 2.4 3.0 R642 16V 10 KANP D605
AUDIO_OUT
50
31
AUDIO_OUT
50V 4.7 KA
6.3V 470 YK
680 1/4W 5.6K 11ES1-EIC
C625 2.3 0 R647
C610
51
30
AUDIO BYPASS R IN
W848
1 F C631 3.0 2.2K

13 12
4.7 R643
1.8 Y/C_AUDIO VD
52
29
AGC 1 EXT AUDIO IN V PULSE OUT
C623 0.0047 B
1 F 2.0 47K R648
TU_AUDIO 0
NC
53
28
2 FM DIRECT OUT G IN
R618 10M 46 SW REG CONT 34 EXT C in
3.2 2.2K
2.5 C632 47 LIMITER IN 33 8.7V REG OUT 0.1 OSD_BLK
3 VIF VCO F/B
54
27
NC
FAST BLK
C624 48 IF AGC 32 X’TAL
2.5 R607 50V 2.2 KA 9.0 C658 R652
SCL 4 16V 47 YK 49 QIF OUT 31 ACL/ABCL 7.3
55
26
VREG Vcc PROTECT
50 AUDIO OUT
R665
150K
2.5 220 1/2W 0.22 B 4.7K

3.0
R639
SDA 5
12K
C688 C630
56
25
D601 1SS133 VIF APC FILTER fsc OUT NC
5 C627 C659 5
NC
6 R609 680 2.2 0.056 B 100P CH FROM/TO DEFLECTION

D602 4.9 6.3V 100 KA W827
R627
57
24
VIF VIDEO OUT
12K
TECC1040PG32D
MTZJ8.2B
4.9 50V 1 KA
0.1 F
C660
+5V 7 C618 330P CH ACL
0 4.9
58
23
VIF GND VIDEO CHROMA Vcc GND

NC
8 C664
0 4.8
100P CH
100P CH
V_OUT
59
22
C604
C605
29.3 C621 0.01 F V RAMP CAP

+30V 9 63V 1 MKT HEATER
2.4 R641
AFT_M 2.0
60
21
AFT OUT V_FEEDBACK

TU601
NC
10 R614 390K V RAMP FEEDBACK

R649 22K
2.9 64 VIF IN 17 V OUT 0 180V
0
61
20
IF 11 NC QIF IN 1 VIF IN B IN
16 B OUT H_OUT
2.2K
15 14 R601 2.3 8.0 W874 R613 H.PLUSE
12K
62
19
POWER ON CONT
RF AGC OUT STRAT UP Vcc

2.2K H_GND
H.PLUSE OUT
C622 2.7 8.0

IF AGC FILTER
AFC FILTER
63
18
H VCO F/B
0.22 B
VIF Vcc
H OUT
R OUT
G OUT
C634 1.5
FBP IN
4 3.7 V_OUT 4
SCL
64
17
DEF
SDA
1
0.01 F
16V 47 KA
3
MTZJ6.8B
C602
0.01 F
C653
C655
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
D615
OSD_R
0.022 F L601 CHROMA IC 1.5 5.0 5.0 2.5 3.2 0.4 2.6 0 0 3.0 3.3 4.0 4.0 4.8 2.8 3.0
0.1 F
C687
3192001 IC601 OSD_G

C675
MTZJ6.8B
MTZJ6.8B
MTZJ6.8B
W871 W901 M61206FP

D609
D610
D611
OSD_B
0.01 F
SAW FILTER 68P CH

C639
R626
CF601SAFGP45M7VFYZR0B
10K
D621
IN IN G OUTOUT
1 2 3 4 5 1SS133 W850
HD
1.5K
1.5K
1.5K
100
1 B
C645
S818X
R656
W5RH3.5X5X1.0
R624
2K
1K
R636
W862
W878
W872
R658
R659
R660
TO CRT
68P CH
CP851A (CP851B)
B602
0.01 F
C647
B2013H02-10P
3 GND 3
10
D620 CUT_OFF CUT OFF
R666
1/4W
100
FROM/TO TV POWER 9
R631
R657
6.8K
D619 B.OUT B.OUT

C629
1K
1SS133 8
AT+30V
G.OUT G.OUT
GND 1SS133 7
R635
R.OUT R.OUT
100
W846
6
C656 W828
NC
UNREG+8V NC 5
0.01 F H_GND1 H GND
AT+12V 4
R650 HEATER HEATER
P.CON+5V_SW CUT OFF SW 3
470 1/4W Q608 NC
R602
R603
NC 2
100
100
AT+5V
KRC111SRTK 180V 180V
VCR_POWER_H
1.0 1SS133 1
1SS133
1SS133
1K 1/4W
R655_1
FROM MICON POWER_OFF_H

H.PLUSE
0.4 FROM TV POWER

AT+5V
H_OUT
R.OUT
G.OUT
B.OUT
R672
TV_POWER_H 0
SCL
SDA
AT+12V
2 2
D614
D612
D613
3.7 1K 1/4W
4.5 H CONTRO
Q612 0.8 PROTECT
4.5
TUNER VIDEO SIGNAL 0 0 KRC102SRTK 5.0 Q609
H CONTRO
KRC111SRTK
Q611
R.SIGNAL S107Y S107X
0 KRC102SRTK 0
H_GND
G.SIGNAL
PCB010
B.SIGNAL PROTECT VMA227
DEFLECTION SIGNAL
LUMINANCE SIGNAL CAUTION: DIGITAL TRANSISTOR
1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
COLOR SIGNAL WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PLAYBACK VIDEO SIGNAL IS NON POLAR ONE. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-7 G-8

A B C D E F G H
SOUND AMP SCHEMATIC DIAGRAM

8
(SYSCON PCB) 8
7 7
FROM/TO IN/OUT
W808
SP_OUT
SOUND+
SOUND_GND
6 6
W814
5 8.2 3.5 0 3.4 5

5 6 7 8
AN7511
SOUND AMP IC
+ -
IC351
4 3 2 1
FROM MICON 5.1 0 0.3 3.9
R359
TV_A_MUTE
47K
R353
TV_POWER_H
4 68K C301 4
50V 2.2 KA
0.0068
50V 10 YK
B
C356
C351
FROM TV POWER
16V 2200 YK
SOUND+B
C357
C354
GND
0.001 CH
SOUND_GND
R352
4.7K
FROM CHROMA/IF
C355
R357
AUDIO_OUT
16V 10 KA 5.6K
3 3
2 2
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE AUDIO SIGNAL(REC)
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES
DESCRIBED IN PARTS LIST ONLY
DANS LA NOMENCLATURE DES PIECES PCB010
VMA227
1 1
A B C D E F G H
G-9 G-10

A B C D E F G H
POWER SCHEMATIC DIAGRAM

8 5A 125V 2.5A 125V (SYSCON PCB) 8
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE FUSE 5A 125V
(F501) AND 2.5A 125V (F502)
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE

N’UTILISER QUE DES FUSIBLE DE MEME TYPE 5A 125V
(F501) ET 2.5A 125V (F502)
7 7
TO SOUND AMP
C516
SOUND+B
500V 470P B
S802X
D505 GND
SB290S
2.5A 125V
TP601 SOUND_GND
+-10%
DEGAUSS D521
2.7M 1/2W
COIL
R500
6 L503 RM11C-EIC R528 F502 6
1SS133
D508
8R140031 CP502 D518 0.22 1W 2.5A125V
R504 R506 R510 +B
500V 0.001 B
A1561WV2-2P
RM11C-EIC
1M 1/4W
FH504 FH503
1 1M 1M 1M 51MS025LCC
1
C507
EYF-52BC EYF-52BC
R511
2
2
B501
TO Y/C/AUDIO/HEAD AMP
003P-2100
003P-2100
BL02RN2-R62T2 D535
0.001 B
10 3W
500V
R502
CP505
CP504
C508
GND
B503 D510_1 R512
121.7 D R517 MTZJ18B AT+30V P.CON+5V
G 3.4
D530 W5RH3.5X5X1.0 RU2AM-EIC 56K 1/2W
D520
2KV 0.001
R
2KV 820P R
TO DEFLECTION
200V 220 YXF

0.5 S SWITCHING 330 1W
C535
TH501_1 R508
C541_1
W838 RM11C-EIC RM11C-EIC Q510 C517
GND
C521
S5NC50FP C510
56K 1/2W
MTZJ33B
ZPB45BL3R0A 2KV 0.0022 R +B
BLADE
D515
C509
WIDE
S101A HS501_1 0.0056 B

5 WHITE AT+12V 5
763WSAA013
200V 470 UP
PHE840
L502
R514 H_GND_1
1R0A103F24
100V 0.01 MKT
BLACK S102A H_GND

C518
C506
AC120V_60Hz 3 4 0.33 1W
275V 0.22
5A 125V FROM/TO IN/OUT

C515
CD501
0R414903 500V 470P B
F501 1 2
5A125V D512 GND
D533 AT+12V
SB290S
51MS050LCC 1SS133 TO MICON
R501
1SS133
FH502 FH501
D514
25V 470 YK
EYF-52BC EYF-52BC GND
C511
F
2.2 5W
C527
C532
P.CON+5V
1
270P B
D537 R531
1/4W
560 1/4W
1SS133 22
POWER_FAIL2
T501
R525
R524
1.8K
4 FEED BACK
81290804 4
IC502
54.4 8.02 GND
TLP621(GR) NC 10 C505 (MOTOR GND)
4
1
3.4 SWITCHING 500V 470P B

C554 0.4 DC IN SB
Q511 8 11 D507
2
0.0022 B KTC3203_Y MOTOR+12V

15.7 0.4 0.5
470
53.6
YK
6.0 SG SB290S-B-EIC
C523
12
B
1.2K 1/4W
MTZJ18B
FEED BACK
D534
C536
35V
5.4
+B ADJ
VR502
D517
R533
SWITCHING
0.022
330
12V POWER_FAIL
Q507 NC 6 13
KTC3198 10ELS2N
D536 C519 R640 10 1/2W
5V UNREG+8V
5 14
R530 R532 COL W856
C522_1 16V 1000 MHE
R651 10 1/2W
MHE
10ELS6N 500V 470P B

1K 4.7K 1/4W LG D519
4 NC 15
C524
3 5V REG IC 3
C537
R527
10K
50V 47
R513 SB290S IC501 KIA78R05PI

39K 1/2W
135V
R553
10K 3 16
S802Y FROM/TO CHROMA/IF
160V 1 KA
1 1/2W
D501 4.9
2 H_GND
R503
17
R505 HG
KX
GND
250V 470P KX
AT+30V
R529_1
4.20
2.7K
MTZJ10B 4.89 330 1/4W 12V

250V 0.0033
1 18
C530
IN OUT GND SW
C539
POWER_FAIL
22K 1/4W
ADJ
D513
MTZJ5.6B
Q505 1 2 3 4 AT+12V
R516
10K
R554
2SA1037AK
D528
UNREG+8V
1SS133 W834
C534
POWER_FAIL2
POWER_FAIL
R507
AT+5V
16V 1000 YK R522
47K
AT+5V
HS504
P.CON+5V_SW
NC 763WSA0019 100 1/4W
GND
2 2
S825X
PCB010
VMA227
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE
1 THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST 1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
IS NON POLAR ONE. DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-11 G-12

A B C D E F G H
DEFLECTION SCHEMATIC DIAGRAM

8 (SYSCON PCB) 8
V.OUTPUT IC
IC401 AN5522
THERMAL PROTECTION
-
AMP
+
PUMP UP
Vcc GND
1 2 3 4 5 6 7
7 3.6 25.9 2.0 0 12.5 26.3 3.7 7
D402
35V 100 MHE
1N4937
35V 1000 YK
11E1-EIC
D401
C406
220 1/2W
C402
TO DY
R421
CP401
18 A1561WV2-A5P
5
100V 1 1/2W
R449
2.2K METAL
4
330 1/2W
W840
VR401
V.POSI
R419
MTZJ30B
3
0.22 TF
D403
R401 W857 NC 2
C451
6 1 6
470 R413 R416
1.8K 82K
R414
25V 1000 YK
12K
33K +-1%
C407
R411
50V 1 KA
MTZJ30B
FROM MICON
680 1/4W
C405
D404
R408
H_CTL
1/2W
FROM/TO CHROMA/IF 17
R415
HS401
V_OUT 763WSAA013
2.2
V_FEEDBACK V801
W807 A34JXV70X53N45
5 GND 5
ACL
L401
H.PLUSE 9
4.7mH 0909 W820
10
8 R
HEATER
250V 1 MHE
6 G FROM/TO DECK
H_GND W863
B
C422
PMS
11
180V 5 7 1 CD803
D407 D411
AT+5V CH012101
250V 0.47
C423
1SS133 1SS133
H_OUT
4.89 H CONTROL
0.05 SWITCH
68 1/2W
1/2W 680
1/2W 680
R447
Q407 2 1
R402
R422
0.3 2SC2412K TO CRT

CD801
SM1098-009-1A
W890
1K 1/4W
4 FB401 3213015R 4
W5RH3.5X5X1.0
R404
262.0 COL
1 HV
B403
W832
H.OUTPUT 136.0 E180

20 6
T401
W823
W917 Q406
ETH09K14BZ 2SD2627LS
MPP
C416 135.0 B+
W853 31.0 0 19 -CBC11 262.0 2
3 4
W816
22P CH NC 0 AFC
0.0022 B
1.25KV 0.0091
31.0 2
0.2 1.3 9
C424
500V
C417
0.5 0 FOCUS
1 6 R450 HEA
500V 0.001 B
W5RH3.5X5X1.0
H-DRIVE 22.3 1.3 8.1 F

W884
TER
100 1/4W
Q405 0 10
50V 22 YK
C438
HS402 5.6 1W
R460
4.7K 1/2W
2SC1627_Y SCREEN
GND S
C418
763WSAA013
8
B402
R456
FROM TV POWER
0 E12 GND 0
W813 W824 NC
4 11
GND 22.3
3 3
22K +-1%
E27
W907
H_GND 3 ABL 0.7

R439
1.5 7
GND
H_GND_1 8
E8
W915 NC 5
1N4937
AT+12V
D413
(W058)
25V 330 YK
+B
18K +-1%
R444
R441 R440
C433
250V 2.2 YK
56K 51K 1/4W

C431
HZ27-1L
R442 D412
D408
FROM/TO MICON
D409 15K +-1% 1N4937
X_RAY CAUTION: DIGITAL TRANSISTOR
0
4.9 HZ11B3L
8.2K +-1%
2 X-RAY_TEST 2
MTZJ6.8B
R420
50V 0.1 YK
D410
68K 1/4W
SWITCHING 0 10.8
11E1-EIC
Q403
R490
D405
0
C432
KRC111SRTK SWITCHING
Q404 0 W847
KRA104SRTK R423
10K 1/4W
W811
PCB010
VMA227 R453 W817
180K 1/4W
1 ATTENTION: LES PIECES REPAREES PAR UN ETANT NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. 1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP DEFLECTION SIGNAL
IS NON POLAR ONE.
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-13 G-14

A B C D E F G H
CRT SCHEMATIC DIAGRAM

8
(CRT PCB) 8
0 0
J801_1 126.5
HPS3200-010501 6
0 5 7 104.1
4 8
3 9 127.5
127.5
1
TP801 F
0
BLUE AMP 21 R802
7 Q804_1 7
2SC4217 132.5 12K 1W
R807
2.8
2.5 2.7K 1/4W
R808
2.7K 1/4W
R814
4.7K
R811
6 FROM CHROMA/IF 6
390 TP802
CP851B (CP851A) C809
B2013H02-10P
22 R805
GND 470P B GREEN AMP
10 GND
Q805_1
CUT_OFF
9 CUT_OFF 2SC4217 132.1 12K 1W
B.OUT
8 B.OUT
2.9
G.OUT 2.5
7 G.OUT
R.OUT
6 R.OUT
5 NC
H_GND1
4 H_GND
HEATER
3 HEATER
2 NC
180V
5 1 180V 5
R815
4.7K
R812
390
C810
470P B TP803
4 R810 4
12K 1W
220uH
L801
23
RED AMP R820
Q806_1
2SC4217 132.3 2.7K 1/4W
2.8
2.5
3 3
W836
R816
4.7K
C801
2KV 0.0022 B
R813
390
C811
470P B
ACCESSORY
C805
TM101
ANT001 R25-1195
100P CH
2 T4-216BNK-BK 2
FROM DEFLECTION
FOCUS
CP801 (CD801)
S801 SCREEN
A2361WV2-2P
GND
GND
PCB110
TCA377
2
1
1 R.SIGNAL 1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE G.SIGNAL
DANS LA NOMENCLATURE DES PIECES B.SIGNAL
A B C D E F G H
G-15 G-16

A B C D E F G H
OPERATION SCHEMATIC DIAGRAM

8 (OPERATION PCB) 8
7 7
LTL-4224-031A
LTL-4224-031A
OS753
REC/OTR
PIC-37143TH5
T-REC
D793
D791
0
R766 3 GND
4.5
2 B+
10 1/4W 4.5
1 Vout
R778_1 R771_1 R772_1 R773_1 R774_1
1/4W
270 1/4W
6.3V 220 KA
R793_2
R754_2
C755_1
820 1/4W 1K 1/4W 1.5K 1/4W 2.7K 1/4W 5.6K 1/4W
POWER ON/OFF
270
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
STOP/EJECT
REW/REV
REC/OTR
SW751
SW795
SW791
SW792
SW793
SW794
FF/CUE
PLAY
6 6
R775_1 R776_1 R777_1
FROM/TO IN/OUT 820 1/4W 1K 1/4W 1.5K 1/4W

EVQ21505R
VOL DOWN
EVQ21505R
EVQ21505R
EVQ21505R
CH DOWN
SW798
SW797
CH UP
CD757 (CP757_2)
SW799
SW796
VOL UP
HEADPHONE_JACK
CH2A019A J351
HTJ-035-28A
10 REMOCON_IN
1
9 GND
NC 5
8 AT+5V
4
5 7 NC 5
W811
R350_1 3
6 NC W815
5 KEY_A 2
W805 22 1/4W
4 T-REC_LED 6
3 REC_LED 7
2 KEY_B
1 NC
R351 W814
W812
22 1/4W
16V 100 KA
4 4
C382
H H
2 4
3 E
1
E
3 3
VIDEO AUDIO L
FRONT AV JACK
J701_1
AV2-24D-5
FROM/TO IN/OUT
CD351_1 (CP353_1)
CH27090A
7 FRONT_VIDEO_IN
6 GND
5 FRONT_AUDIO_IN
4 SOUND_GND
2 2
3 SOUND_OUT
2 SP_OUT
1 GND
SPEAKER CD352 CH12435A

1 SP + PCB030
2 SP - TEXA28
SP351
SG04D11BNA
8 OHM
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: SINCE THESE PARTS MARKED BY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT
1 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE TUNER VIDEO SIGNAL 1
DANS LA NOMENCLATURE DES PIECES AUDIO SIGNAL(REC)
A B C D E F G H
G-17 G-18

A B C D E F G H
INTERCONNECTION DIAGRAM
8 8
J351 E E
1 3
OPERATION PCB
1 PCB030
J
2 4 HALL MAIN ROTOR
5 H H TEXA28 MR
SENSOR COIL MAGNET
4 VIDEO AUDIO L FG SENSOR
3 FRONT AV JACK 1
VCC
J701_1
O
G
2
2
TM101 LM
6
7 OS753 LOADING MOTOR
7 M101 7
GND HALL HALL OUT
VCC IN SWITCH
8 OHM CD352 LOGIC
B+
2 SOUND GND
V.OUT
1 SP OUT CP1001
SPEAKER
1 CAP_FG 1
CD351
SP351
CD757
2 CAP_VCO 2
REMOCON_IN 10
9
8
7
6
5
4
3
2
1
FRONT_VIDEO_IN 7
6
FRONT_AUDIO_IN 5
4
SOUND_OUT_L 3
2
1
3 VCC 3
4 CAP/M/F/R 4
SOUND_GND
SP_OUT_L
T-REC_LED
REC_LED
5 I_LIMIT 5
AT+5V
KEY_A
KEY_B
GND
GND
GND
6 MOTOR_GND 6
7 GND 7
6 8 LD/CY_VCO 8 6
CP757_2
10
9
8
7
6
5
4
3
2
1
7
6
5
4
3
2
1
9 CAP_CTL 9
CP351_1
AC120V_60Hz
10 LDM_CTL 10
CD501 CAPSTAN DD UNIT
11 CYL_FG/PG 11 DECK MECHA ASS’Y
BLADE
WIDE
S101A 12 CYL_CTL 12 M2001

WHITE
BLACK S102A
1
2
3
5 4 5
5
DEGAUSS COIL
L503 6
CP502 7
2 DEGAUSS COIL
2
1 DEGAUSS COIL
1
FB401
FBT
MICRO MOTOR
CD2001
FFC M2003
U-OUT 1
V-OUT 2
W-OUT 3
4 4
M-COM 4
GND 5
PG OUT 6
FOCUS SCREEN
PG GND 7
CYLINDER UNIT ASS’Y

CP401 UN4001
5 CP4001_1 CH2
4 1 1
3 2 SP-CH2 (L) 2
3 SP COM 3 SP
NC 2
CH1 HEAD
1 4 SP-CH1 (R) 4
3 3
CP851A
TUNER
GND 10 PACK
ANODE
HEAD AUDIO CONTROL ASS’Y

CUT OFF 9 TU601
S801 H5001
B.OUT 8
6 CP4002 FFC
SCREEN
FOCUS
5 7 G.OUT 7
11 IF 6 AUDIO PB 6 AUDIO PB AUDIO
4 8 R.OUT 6
V801 5 AUDIO REC 5 AUDIO REC
CRT SOCKET NC 5 NC 10
3 9
J801 4 CTL+ 4 CTL+
H GND 4 9 +30V CONTROL
CRT
H.V
3 CTL- 3 CTL-
HEATER 3
1 NC 8 2 AE HEAD(-) 2 AE HEAD(-)
2 F NC 2 2
1 AE HEAD(+) 1 AE HEAD(+)
CP801
7 +5V AE
CP851B
180V 1
10
2
1
9
8
7
6
5
4
3
2
1
NC 6
HEATER
H GND
CUT OFF
G.OUT
R.OUT
GND
180V
B.OUT
5 SDA
GND
GND
NC
NC
CRT PCB
PCB110 CP4003
4 SCL
TCA377
2 FE HEAD (GND) 2 FE HEAD (GND)
NC 3
1 FE HEAD (HOT) 1 FE HEAD (HOT)
SYSCON PCB NC 2
FULL ERASE HEAD ASS’Y
CD801 PCB010
1 AGC H5002
VMA227
U IN
1 1
A B C D E F G H
G-19 G-20

WAVEFORMS
Y/C/AUDIO/CCD/HEAD AMP MICON
1 PB 6 POWER ON 11 PB
0.5V 20µs/div 1.0V 20µs/div 0.5V 0.5ms/div
2 POWER ON 7 POWER ON 13 PB
100mV 0.1µs/div 0.5V 10ms/div 1.0V 5ms/div
DEFLECTION
3 PB 8 POWER ON 17 0.5V 5ms/div

10mV 20us/div 1.0V 10µs/div
4 PB 9 PB 18 10.0V 5ms/div
0.5V 1ms/div 1.0V 10ms/div
5 REC 10 PB 19 2.0V 20µs/div

10.0V 5us/div 1.0V 5ms/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1

WAVEFORMS
20 200mV 20µs/div
CRT
21 50.0V 20µs/div
22 50.0V 20µs/div
23 50.0V 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2

MECHANICAL EXPLODED VIEW
205 J801
PCB110
205 (CRT PCB)
111
205
L503
205
V801
120
116 206
122
206
206 PCB030
(OPERATION PCB)
108
121
207 207
B
123 117
110
125 SP351
115 118
113 101
I-1

MECHANICAL EXPLODED VIEW
202
114
202
207
202
202
209
203
204
204
106
204 119
202
109
103
208
201
210 105
211
112 FB401
211
104
209 102
104
201
PCB010 112 210
(SYSCON PCB)
204
124
107
I-2

F-4
D410
CP351_1
D518
W853
R423
HS501_1 Q510
W009
Q511
W005 W866
C508
C539
C509
W013
R524
W002
R415
C507
D520
W008
W011 50
D534
R
C407 R531
W012
C537
HS401
C405
W807 C610 35 14
D530
TU601
C5 D521
R5
C612 D537
28
W004
D536
IC502
R5
B501
D535
W006
R511
CP502 R501
R517
D533
R421
C515
C406
CP505
L603
D401
W003
IC401
W871
W007 0
C53 TH501_1
W838
D411 L502
W277
D403
D404
R419
R505
CP504
D402 W901
T501
FB401 W840
R449
D528
R408
R490 R529_1
Q507
R532 W014
VR502
2.5A125VOR250V
5A125VOR250V
W001
R533
VR401
C451
D514
R447 C505
C422 W036
W856 D517
C518
R450
W034
C541_1
W832
FH501
B503
S802Y
D507 C506
D512
W043
W283
W290
D519
C42 FH503 F502 D407 C522_1
D505
C516
W890 3
L401
C402
FH504
W811 4
C42 W033
F501
W824
R554
W817
CD501
R453 TP601 C523
D405 W820
W823
R440
C432
FH502
D510_1
B403
S102A
S802X
C521
B402
R553
C517
Q406 CP401 C524 W291 W274
S101A
W816 00
D413
R402 C519 R5
W037
W026
W028
C511
W884
IC501
R651
R640
R508
R512
R422 R503
W023
D515
R460 HS402 D501
D508
C418
W049
Q405
T401
C438
R522
C431
W857 W872
W858
D412
W041
W917
W035
W024
W040
W042
S825X
W031
W045
R607
W030
C534
W022
W032
W021
HS504
C354
W282
W019 C417
W829
D602
D601 D513
C433
W046
C624
W847
R456
W048
Q604
W878
W018
W016
W044
SYSCON/CRT (INSERTED PARTS)
R4007
W029
R4006
C4025_1
Q4001
L4001
C632
W047
R672
W027
Q605
L601
W020
PRINTED CIRCUIT BOARDS
W834
W063 C627 CP4001_1
Q4002
W107
W094
W915 C644 L4006
W091
02
CP40
C4002
C641
CF604
1A
W099
L607
C4009
CP85 C4063
W121
W089 W808
T4001
C355
D408 D614 R654
CF603
W070 C4004 C4062 W112
W105 W103
W096
C4067
SOLDER SIDE
D612 C652
D409
W106
W073 W093 W108
B604
D613 C648 C4012 C4065
CF601 W068 C4023 R612
S818X
L4003
Q606
W828
Q4005
W848
C356 W111
W104
IC351
W067 R668
W061
Q4006
R4004 W118
W895
C351
W279 W071 C649 W088 C4058
W862 W082 C4030
W097
X602
C4027 C4048 W119 W814
W827
C664
W863 TP1002
C687
R404
W076
W122
W280 R1064 W897 C4031 C4034 C4051 C4052
W109
W085
W075
W813
TP4001
W054
S107X
W092 W080 C4035 C4049

B602 X4001
C4046
C1007 W056 W064 C4010
L4005
CP4003
C659
01
D615 W065 D4003
L612
10
W057 W072 W081
R1008
CP353_1
CP
W110
W055 W113
R655_1
W066 C4053
W059 C655 W087
C4045
CD852
W074 W117 W115
W888
W060 L1003 W084
W101
W874
W100
R4028
W098
R4014
W120
D610
S825Y
W114
W095
C1001 W086
R4032
R4029
W051
W140
W210 W078
C665 W116
W090
W175 C4047
C1032 W077
D605 W069 W171
W184
W223
W123
TP1001
Q1013
C4042
W181
W168
W189
W138
W205
W222
W192
W129
W152
W208
W206
D621 W169
W194
W212
W135 W221
W195
W167
D619
L4009
W126 R4048
Q1011
R666 W165 W218
01 W149 W162
D1003
P8 D611
W220
W214
C D620 W160
R1028
W209
R650
W156 W231 W225
W137 W145
W153
CP1003
C1018
W229 W190

S818Y W142 W178 W196
D609 W154
W141 C1016
W186 W197 W227
R805
R802
W130 W155 W228
C1020
W213
W288 W157
W146 C1015 W191 W825
R807
R808
R1016
J801_1
W850 W158
W143 W179 W198
W131 W159
W147 W211
W164 W230
W148 W286 W207 W193
R4016
W912
W124 W170 W161 W199
W217
TP802
TP801
W151
W173 W201
W185
CP757_2
W177
W805
W174 W285
W127
W187
W188 W806
W128
W287
R1010
W836
W125
C801
W215
W144
W203
W139
W202
W180
W232
S801
W182
W134
W163
IC1099
9
W166
00 W273
W200
W176
Q1005
CD803
Q1
R820
10
W150
W269
Q806_1
R8
W172
W247
W239
Q804_1
L1001 W270
S107Y
TP803
W268
Q603
W243
W240
Q805_1
W253
W245
X1002
L801
W249
851
X1001
W246
W250
W266
Q1003
W276
W242
W255
CP
W248
W254
W272
C1058
W801
W234 R1066
W257
W236
W267
W289
W237
W238
W233
Q602
C643
D608
W262
R1051
W244
SW1001
C1021
W259
D1001
C1003_1
F-3
F-5
C510
C604
R527
R401 C536
R411
C605
R416 R414
R413 C532
R525
C602
R510 R506 R504
C554
R441

R530
R516
R507
R513
Q505
C416
C631
R420 W907
W025
R444 R439
C623
R616 W880
Q404
R4053
R4052
C527
R618
R609
C4020
R628 C4015
R4001
Q601
C4019 R4051
C4069
R620
C4016
C4021
W284
R442
R4002
C674
R4003
W865
R601
C672
R608
C4064 R4039
Q4003
R665 R4064
61
C640
R4015 R4012
C4055
C618
R625
R622
R615 R610 C4066
IC R4038 R4042
C650
R4010
C636
1
40
41
01 C4059 R357
C625 R633
W887
C4005 C4006
R4011
R352
C4061
W818
C622 C4074
Q609
R644 R669
49
R4020 C4028
21
C301 R353
C651
R4041
R4043
C654
C634
IC R4018 R4017
Q4012
R636
R4055
1
60
33
C4060
R359
1 C4029 C4032
Q407
R4035
SOLDER SIDE
R646 R4060
C660 R4019 R4021
R4034
C4037
R4037 C4033
Q612
R647 R4024 C4036 R4068 R4062 R4033
C4014_1 R4022
17
C688 R4023 C4054 C357
Q611
C675 R4057 C4024_1
C673
R676
Q4010
R656
R626
C629 R4056 C4050
C639 R4025 C4044
C647
R624 R658 R638
R4058
R657
R4201
R603
C4038
R648 C4057
C4075
C653
W873
C4076
R641 R631 R649
R4054
C1042_2
R643
R639
W846
C645
Q4011
R635
R660
R613 R627
Q4007
R4061
R4059
Q4009
R1025
C4041
R1073
R652
C630
C658
R4045
SYSCON/CRT (CHIP MOUNTED PARTS)
R4044
R659 R642 R1011
C1089
W894
R4047
Q1023
R1075
C1028
R602
R1035
Q1024
R614 R1012
R1017
R1029
C621 C1019 C1065 R1007

R4026
R1013
R1021
C1009
Q1007
R1020 C1010 C1004

C4043
Q608
C1029
Q1004
R1009
C1023
R1042
Q1008
C1037
R1053
C656
R1063
R1054
R1044 R1036
C1022
C1013 R1045
R1038
C1062
C1027
C1084
R1033
R1048
C1034
R1078 R1034
C1060
R1031
81
C1025
R1022
C1035
C1031
C4206_1
C1071
C1038
C1061
W903
R1001
R1087
C1056
1
R1052 IC R1032
R1050 10 C1039_1
R1055
R1019 01
51
C1082
R1030
C1046 R1040
C1047
R1070
31
C811 R1005
R1083
R813
C1026
C805
C1040
C1083
C1049 C1048
R816
R814 R815 R663 R1047
W810 C1068 C1050
R1046
R812
C810
C667
C809
R811
Q403
C1043
IC1003
R1018
C1017
R1049
F-6
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK
make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE [Note 1]
If you have not the 500V insulation
In the condition that an explosion-proof cathode- resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to Earphone jack
deal with it.
HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
A1-1

CONTENTS
SERVICING NOTICES ON CHECKING .................................................................................. A1-1

HOW TO ORDER PARTS ....................................................................................................... A1-1
CONTENTS ................................................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................... A3-1~A3-4
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ............................................ B1-1
2. REMOVAL OF DECK PARTS ............................................................................................ B2-1~B2-6
3. REMOVAL OF ANODE CAP .............................................................................................. B3-1
4. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................. B4-1, B4-2
KEY TO ABBREVIATIONS ..................................................................................................... C1-1, C1-2
SERVICE MODE LIST ............................................................................................................ C2-1
PREVENTIVE CHECKS AND SERVICE INTERVALS ............................................................ C3-1, C3-2
WHEN REPLACING EEPROM (MEMORY) IC ..................................................................... C4-1
SERVICING FIXTURES AND TOOLS ..................................................................................... C5-1
PREPARATION FOR SERVICING ......................................................................................... C5-1
MECHANICAL ADJUSTMENTS ............................................................................................. D1-1~D1-4
ELECTRICAL ADJUSTMENTS ............................................................................................... D2-1~D2-5
BLOCK DIAGRAMS
TV ............................................................................................................................................ E-1, E-2
Y/C/AUDIO/CCD/HEAD AMP ................................................................................................. E-3, E-4
MICON/OPERATION/IN/OUT ................................................................................................ E-5, E-6
OPERATION ............................................................................................................................ F-1, F-2
SYSCON/CRT ......................................................................................................................... F-3~F-6
SCHEMATIC DIAGRAMS
Y/C/AUDIO/CCD/HEAD AMP ................................................................................................. G-1, G-2
MICON ..................................................................................................................................... G-3, G-4
IN/OUT ..................................................................................................................................... G-5, G-6
CHROMA/IF ............................................................................................................................. G-7, G-8
SOUND AMP ........................................................................................................................... G-9, G-10
POWER ................................................................................................................................... G-11, G-12
DEFLECTION .......................................................................................................................... G-13, G-14
CRT .......................................................................................................................................... G-15, G-16
OPERATION ........................................................................................................................... G-17, G-18
INTERCONNECTION DIAGRAM ............................................................................................ G-19, G-20
WAVEFORMS ............................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEWS ........................................................................................... I-1, I-2
CHASSIS EXPLODED VIEWS ................................................................................................... I-3, I-4
MECHANICAL REPLACEMENT PARTS LIST ......................................................................... J1-1
CHASSIS REPLACEMENT PARTS LIST .................................................................................. J2-1
ELECTRICAL REPLACEMENT PARTS LIST ........................................................................ J3-1, J3-2
A2-1

GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G / 0.18G
Color System NTSC
Speaker 1Speaker
Position Front
Size 1.5 x 2.5 Inch
Impedance 8 ohm
Sound Output MAX 1.5 W
10%(Typical) 1.0 W
G-2 VCR System VHS
System Player / Recorder
Video System NTSC
Hi-Fi STEREO No
NTSC PB -
Deck DECK OVD-7
Loading System Front
Motor 3
Heads Video Head 2 Head
FM Audio Head No
Audio /Control Mono/Yes

Erase(Full Track Erase) Yes
Tape Rec PAL -
Speed NTSC SP/SLP
Play PAL -
NTSC SP/LP/SLP
Fast Forward / Rewind Time (Approx.) FF:4'50"/REW:2'30"
Cassette at T-120
Forward/Reverse NTSC or PAL-M SP/LP/SLP=3x,5x/7x,9x/9x,15x
Picture Search
Frame Advance Slow -
Slow Speed Variable Slow -
G-3 Tuning Broadcasting System US Sysytem M
System Tuner and System 1Tuner
Receive CH Destination USA+CATV
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2~69, 4A,A-5~A-1, A~I,
CH Coverage
J~W,W+1~W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.5MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-4 Signal Video Signal Input Level 1 V p-p/75 ohm
Output Level -
S/N Ratio (Weighted) 50 dB
Horizontal Resolution at SP Mode 220Lines
Audio Signal Input Level RCA-8dB/50Kohm
Output Level -
Harmonic Distortion at SP (1KHz) Typical 1.5 %
Frequency Response at SP 100Hz - 10kHz
at LP 100Hz - 6kHz
at SLP 100Hz - 4kHz
Hi-Fi Audio Signal Dynamic Range : More than -
Wow And Flutter : Less than -
Channel Separation : More than -
Harmonic Distortion : Less than -
G-5 Power Power Source AC 120V 60Hz
DC -
Power Consumption at AC 65 W at 120V 60Hz
at DC -
Stand by (at AC) 5 W at 120V 60 Hz
Per Year -
Protector Power Fuse Yes
Dew Sensor No
G-6 Regulation Safety UL/CSA
Radiation FCC/DOC
X-Radiation DHHS/HWC
G-7 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-8 Operating Humidity Less then 80% RH
G-9 On Screen Menu Yes
Display Menu Type Character
A3-1

Timer Rec Set Yes
Channel Setup Yes
TV/CATV Yes
Auto ch Memory Yes
Add/Delete Yes
Guide ch Set No
TV Setup Yes
V-chip Set Yes
On/Off Timer Set Yes
Picture Yes
Audio No
Sap On/Off No
Auto Repeat On/Off Yes
On/Off Timer Set No
System Setup Yes
Clock Set Yes
Language Yes
Auto Clock On/Off Yes
Standard Time Yes
Daylight Saving Time Yes
Commercial Advance No
Marking On/Off No
Blueback On/Off No
Playback Auto/Manual No
Unmarked Tape No
Movie Advance No
Go To Movie No
Go To Preview No
G-CODE(or SHOWVIEW or PLUSCODE)No. Entry No
Clock Yes
CH/AV Yes
Tape Counter(Linear Counter) Yes
Tape Speed Yes
Sleep Time Yes
Stereo/Audio Output No
Bilingal No
SAP No
Control Volume Yes
Level Bright / Contrast / Sharpness / Color Yes
Tint Yes
Bass/Treble/Balance No
Manual Tracking Yes
Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark) Yes
Auto Tracking/Manual Tracking Yes
Caption / Text Yes
Index No
Muting Yes
Hi-Fi No
Repeat Yes
Zero Return No
DEW No
G-10 OSD Language English French Spanish
OSD Language Setting English
G-11 Clock,Timer Calendar 1990/1/1 ~ 2081/12/31
and Timer Timer Events 8 prog/ 1 month
Back-up One Touch Recording Max Time 5 Hours
OTPB Valid Time No
Sleep Timer Max Time 120 min.
Step 10 min.
On/Off Timer Program(On Tim / Off Tim) 1 prog.
Auto Shut Off No Signal 15 min.
No Operation -
Timer Back-up (at Power Off Mode) 5 sec.
G-12 Remote Unit RC-CG
Control Glow in Dark Remocon Yes
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 41 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
A3-2

9 Yes
0 Yes
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
Input Select Yes
Play Yes
F.Fwd Yes
Rew Yes
Pause/Still Yes
Stop Yes
Rec/OTR Yes
Eject Yes
Counter Reset Yes
Speed Yes
Timer Rec Yes
TV Monitor Yes
Quick View Yes
Program Yes
Slow No
Auto Tracking Yes
Set/Tracking+ Yes
Set/Tracking - Yes
Menu Yes
Enter Yes
Cancel Yes
Call Yes
TV/Caption/Text Yes
Sleep Timer Yes
Muting Yes
Zero Return Yes
CM Skip Yes
Audio Select No
G-13 Features Auto Head Cleaning Yes
Auto Tracking Yes
HQ (VHS Standard High Quality) Yes
Auto Power On, Auto Play, Auto Rewind, Auto Eject Yes
VIDEO PLUS+(SHOWVIEW,G-CODE) No
Auto Clock Yes
Forward / Reverse Picture Search Yes
One Touch Playback No
Auto CH Memory Yes
Closed Caption Yes
TV Auto Shut off Function Yes
End Call No
Index Search No
SQPB No
CATV Yes
CM Skip(30sec x 6 Times) Yes
Comb Filter No
TV Monitor Yes
Program Extend No
Choke Coil No
Energy Star Yes
Dirty Head No
V-chip USA V-chip Yes
CANADA V-chip No
Zero Return Yes
CM Advance No
Movie Advance No
G-14 Accessories Owner's Manual Language English/French
w/Guarantee Card YES
Remote Control Unit Yes
Rod Antenna Yes
Poles 2pole
Terminal F type
w/300 ohm to 75 ohm Antenna Adapter Yes
Loop Antenna No
Terminal -
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
A3-3

Important Safeguard No
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery No
UM size x pcs -
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card No
ESP Card No
300 ohm to 75 ohm Antenna Adapter No
G-15 Interface Switch Power Yes
Play Yes
Pause/Still No
System Select No
Channel Up Yes
Channel Down Yes
F.FWD/Cue Yes
Eject/Stop Yes
Main Power SW No
Volume Up Yes
Volume Down Yes
Rew/Rev Yes
Rec/OTR Yes
Input Select No
Indicator Power No
Rec/OTR Red
T-Rec Red
On Timer No
CS No
Key Light up Rec/OTR No
Play No
Terminals Front Video Input RCAx1
Audio Input RCAx1
Other Terminal Head Phone(Stereo & Mono, 3.5mm)
Rear Video Input No
Audio Input No
Video Output No
Audio Output No
Euro Scart No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Inlet No
G-16 Set Size Approx. W x D x H (mm) 362 x 370.5 x 382
G-17 Weight Net (Approx.) 11.0 kg (24.3 lbs)
Gross (Approx.) 12.5 kg (27.6 lbs)
G-18 Carton Master Carton No
Content -
Material -
Dimensions W x D x H(mm) -
Description of Origin -
Gift Box Yes
Material Double Full Color Carton w/Photo
Dimensions W x D x H(mm) 423 x 447 x 443
Design As per Buyer's
Description of Origin Yes
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height (cm) 62
Container Stuffing(40' container) 700 Sets
G-19 Cabinet Material Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
A3-4

1. REMOVAL OF MECHANICAL PARTS 1-3: TV/VCR BLOCK (Refer to Fig. 1-3)
AND P.C. BOARDS 1. Remove the 2 screws 1.
2. Disconnect the following connectors:
1-1: BACK CABINET (Refer to Fig. 1-1)
(CP757, CP351, CP401 and CP502).
1. Remove the 5 screws 1. 3. Unlock the support 2.
2. Remove the AC cord from the AC cord hook 2. 4. Remove the TV/VCR Block in the direction of arrow.
3. Remove the Back Cabinet in the direction of arrow.
Front Cabinet Front Cabinet 1
1 2
UP TO
RELEASE
1 TV/VCR Block
1 Fig. 1-3
2
Back Cabinet
1 1-4: DECK CHASSIS AND SYSCON PCB
Fig. 1-1 (Refer to Fig. 1-4)
1. Remove the screw 1.
1-2: CRT PCB (Refer to Fig. 1-2) 2. Remove the screw 2.
CAUTION: BEFORE REMOVING THE ANODE CAP, 3. Remove the screw 3.
DISCHARGE ELECTRICITY BECAUSE IT 4. Remove the Deck Shield Plate in direction of arrow (A).
CONTAINS HIGH VOLTAGE. 5. Remove the screw 4.
BEFORE ATTEMPTING TO REMOVE OR 6. Remove the Cover Light Plate in direction of arrow (C).
REPAIR ANY PCB, UNPLUG THE POWER 7. Remove the 3 screws 5.
CORD FROM THE AC SOURCE. 8. Disconnect the following connectors:
CP1001, CP4001, CP4002 and CP4003).
1. Remove the Anode Cap. 9. Remove the Deck Chassis in the direction of arrow (B).
(Refer to REMOVAL OF ANODE CAP) 10.Remove the screw 6.
2. Disconnect the following connectors: 11.Remove the Syscon PCB in the direction of arrow (C).
(CP801 and CP851B).
3. Remove the CRT PCB in the direction of arrow. 1
3
2
CRT PCB
Front Cabinet
5 Deck Shield Plate
5
(A)
5
Deck Chassis
(B)
Syscon PCB
6
4
Fig. 1-2
Cover Light Plate
(C)
Deck Holder
Fig. 1-4
B1-1

2. REMOVAL OF DECK PARTS NOTE
2-1: TOP BRACKET (Refer to Fig. 2-1) 1. In case of the Locker R installation, check if the two
positions of Fig.2-3-B are correctly locked.
1. Extend the 2 supports 1. 2. When you install the Cassette Side R, be sure to move
2. Slide the 2 supports 2 and remove the Top Bracket. the Locker R after installing.
NOTE
1. After the installation of the Top Bracket, bend the
support 1 so that the Top Bracket is fixed.
Locker R
Top Bracket Check if these
positions are locked.
Cassette Side R
1 1
Top Bracket
2
Fig. 2-3-B
2
Main Chassis
2-4: LINK UNIT (Refer to Fig. 2-4)
Main Chassis
1. Set the Link Unit to the Eject position.
Fig. 2-1 2. Unlock the support 1.
3. Remove the (A) side of the Link Unit first, then remove
2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2) the (B) side.
1. Move the Cassette Holder Ass'y to the front side.

Main Chassis
2. Push the Locker R to remove the Cassette Side R.
3. Remove the Cassette Side L.
Link Unit
Cassette Side R
Main Chassis Locker R
(B)
(A)
Link Unit
1
Main Chassis
Fig. 2-4
Link Ass'y
Main Chassis
2-5: LINK LEVER/FLAP LEVER (Refer to Fig. 2-5)
Cassette Side L
Fig. 2-2 1. Remove the Link Lever.
2. Remove the Flap Lever.
2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A)
1. Remove the Locker Spring.
2. Unlock the 4 supports 1 and then remove the Cassette
Side L/R.
3. Unlock the support 2 and then remove the Locker R.
Flap Lever
Locker Spring
1
Cassette Holder Link Lever
1
2
Fig. 2-5
Locker R
1
1
Cassette Side R
Cassette Side L
Fig. 2-3-A
B2-1

2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A)
1
2. Remove the Loading Motor. Tension Connect
1 Tension Band
3. Remove the Worm. 3
Tension Spring Tension Arm Ass'y

Loading Motor
Tension Holder
2
4
Worm
Main Chassis
Fig. 2-7-B
• Screw Torque: 3 ± 0.5kgf•cm 1
Fig. 2-6-A
NOTE
NOTE 1. In case of the Tension Band installation, note the
1. In case of the Worm installation, check if the value of direction of the installation. (Refer to Fig. 2-7-C)
the Fig. 2-6-B is correct. 2. In case of the Tension Band installation, install correctly
as Fig. 2-7-D.
3. In case of the Tension Connect installation, install as
the circled section of Fig. 2-7-E.
19.2 ± 0.1mm
Tension Band
Tension Connect
Fig. 2-7-C
Safety surface for pressing
of the insert.
Fig. 2-6-B
[OK] Tension Connect
2-7: TENSION ASS'Y (Refer to Fig. 2-7-B) Tension Band
1. Turn the Pinch Roller Cam clockwise so that the

Tension Connect
Tension Holder hook is set to the position of Fig. 2-7-A [NG] Tension Band
to move the Tension Arm Ass'y.
2. Remove the Tension Spring.
3. Unlock the 2 supports 1 and remove the Tension Fig. 2-7-D
Band.
4. Unlock the support 2 and remove the Tension Arm
Ass'y.
Tension Connect
5. Unlock the support 3 and remove the Tension
Connect.
6. Float the hook 4 and turn it clockwise then remove the
Tension Holder.
Main Chassis
Tension Arm Ass'y Fig. 2-7-E
Fig. 2-7-A
B2-2

2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A)
1. Remove the T Brake Spring. Idler Gear
2. Turn the T Brake Arm clockwise and bend the hook
Idler Arm Ass'y
section to remove it.
3. Unlock the 2 supports 1 and remove the T Brake
S Reel
Band.
T Brake Band
(A) T Reel
Hook section 1
(A)
1 T Brake Arm
1 T Brake Spring 1
Fig. 2-8-A Fig. 2-9-A
NOTE
NOTE
1. In case of the S Reel and T Reel installation, check if
1. In case of the T Brake Band installation, install correctly
the correct parts are installed. (Refer to Fig. 2-9-B)
as Fig. 2-8-B.
2. In case of the Idler Arm Ass'y installation, install
correctly as Fig. 2-9-C.
[OK] T Brake Arm
T Brake Band
[NG] T Brake Arm

T Brake Band
Fig. 2-8-B
Big Hole Small Hole
(S Reel) (T Reel)
2-9: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR Fig. 2-9-B
(Refer to Fig. 2-9-A)
1. Remove the S Reel and T Reel. [OK]
2. Remove the 2 Polyslider Washers 1. Clutch Gear
Idler Arm Ass'y
3. Remove the Idler Arm Ass'y and Idler Gear.
NOTE
[NG]
1. Take care not to damage the gears of the S Reel and T Idler Arm Ass'y
Reel. Clutch Gear
2. The Polyslider Washer may be remained on the back of
Fig. 2-9-C
the reel.
3. Take care not to damage the shaft.
4. Do not touch the section "A" of S Reel and T Reel. (Use
gloves.) (Refer to Fig. 2-9-A) Do not adhere the stains
on it.
5. When you install the reel, clean the shaft and grease it
(MG-33). (If you do not grease, noise may be heard in
FF/REW mode.)
6. After installing the reel, adjust the height of the reel.
(Refer to MECHANICAL ADJUSTMENT)
B2-3

2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/ (1) (3)
P5 ARM ASS'Y (Refer to Fig. 2-10-A) 2 2
1. Unlock the support 1 and remove the Cassette 2

Opener. (2)
2. Remove the Pinch Roller Block and P5 Arm Ass'y. A/C Head
Cassette Opener
1
A/C Head Spring
Pinch Roller Block

1
A/C Head Base
P5 Arm Ass'y
• Screw Torque: 5 ± 0.5kgf•cm (Screw 1) Fig. 2-11-A

Main Chassis
Fig. 2-10-A
NOTE
Spring Position
Fig. 2-11-B
1. Do not touch the Pinch Roller. (Use gloves.)
2. In case of the Pinch Roller Block and the Pinch Roller
Cam installation, install correctly as Fig. 2-10-B. 2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12)
2. Remove the FE Head.
Pinch Roller Block Can be seen the hole of 1
the Pinch Roller Cam.
FE Head
P5 Arm Ass'y
Can be seen the hole of the

Main Cam.
Fig. 2-10-B
2-11: A/C HEAD (Refer to Fig. 2-11-A)

1. Remove the screw 1. • Screw Torque: 5 ± 0.5kgf•cm
2. Remove the A/C Head Base. • The FE Head is not installed on the Video Cassette Player. Fig. 2-12
3. Remove the 3 screws 2.
4. Remove the A/C Head and A/C Head Spring.
NOTE
1. Do not touch the A/C Head. (Use gloves.)
2. When you install the A/C Head Spring, install as shown
in Fig. 2-11-B.
3. When you install the A/C Head, tighten the screw (1)
first, then tighten the screw (2), finally tighten the screw
(3).
B2-4

2-13: AHC ASS'Y/CYLINDER UNIT ASS'Y 2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR
(Refer to Fig. 2-13) (Refer to Fig. 2-15-A)
1. Unlock the support 1 and remove the AHC Ass'y. 1. Remove the E-Ring 1, then remove the Main Cam.
2. Disconnect the following connector: 2. Remove the E-Ring 2, then remove the Pinch Roller
(CD2001) Cam and Joint Gear.
4. Remove the Cylinder Unit Ass'y. 1
NOTE Main Cam
1. When you install the Cylinder Unit Ass'y, tighten the

screws from (1) to (3) in order while pulling the Ass'y 2
toward the left front direction.
Pinch Roller Cam
Joint Gear
Cylinder Unit Ass'y
AHC Ass'y
Fig. 2-15-A
1
NOTE
1. In case of the Pinch Roller Cam and Main Cam
installation, install them as the circled section of Fig. 2-
(3) 15-B so that the each markers are met. (Refer to Fig.
(2) 2 2-15-B)
(1) 2
2
• Screw Torque: 3 ± 0.5kgf•cm
Fig. 2-13
Pinch Roller Cam
2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14)

Marker
1. Remove the Capstan Belt.
3. Remove the Capstan DD Unit.
Main Cam
Capstan Belt
Capstan DD Unit
Fig. 2-15-B
2-16: LOADING GEAR S/T UNIT (Refer to Fig. 2-16-A)

1. Remove the E-Ring 1 and remove the Main Loading
Gear.
2. Remove the Main Rod, Tension Lever, Loading Arm S
Unit and Loading Arm T Unit.
1
Main Loading Gear
1 Main Rod
1 1
• Screw Torque: 4 ± 0.5kgf•cm Fig. 2-14
Loading Arm T Unit
Tension Lever
Loading Arm S Unit
Fig. 2-16-A
B2-5

NOTE 2-18: CASSETTE GUIDE POST/INCLINED BASE S/T
UNIT/P4 CAP (Refer to Fig. 2-18-A)
1. When you install the Loading Arm S Unit, Loading Arm
T Unit and Main Loading Gear, align each marker. 1. Remove the P4 Cap.
(Refer to Fig. 2-16-B) 2. Unlock the support 1 and remove the Cassette Guide
Post.
Marker 3. Remove the Inclined Base S Unit and Inclined Base T
Unit.
Main Loading Gear
Cassette Guide Post
Marker 1
Inclined Base S
Unit Inclined Base T
Unit
P4 Cap
Loading Arm T Unit Loading Arm S Unit
Fig. 2-16-B
2-17: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/

CLUTCH GEAR (Refer to Fig. 2-17-A)
1. Remove the Polyslider Washer 1.
2. Remove the Clutch Ass'y and Ring Spring.
3. Remove the Clutch Lever. Fig. 2-18-A
4. Remove the Coupling Gear, Coupling Spring and
Clutch Gear. NOTE
1
1. Do not touch the roller of Guide Roller.
2. In case of the P4 Cap installation, install it with parallel
for "A" and "B" of Fig. 2-18-B.
Clutch Ass'y
3. In case of the Cassette Guide Post installation, install
correctly as the circled section of Fig. 2-18-C.
Ring Spring
"A" "B"
Coupling Gear
Clutch Lever
Coupling Spring
Clutch Gear
P4 Cap
Cassette Opener
Fig. 2-18-B
Fig. 2-17-A
NOTE [OK]
1. In case of the Clutch Ass'y installation, install it with Cassette Guide Post
inserting the spring of the Clutch Ass'y into the dent of
the Coupling Gear. (Refer to Fig. 2-17-B)
Clutch Ass'y
[NG]
Cassette Guide Post
Coupling Gear
Fig. 2-18-C
Fig. 2-17-B
B2-6

3. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap amount of alcohol. (Refer to Fig. 3-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 3-1.)
Connect one end of an Alligator Clip to the metal part of a Location of Anode Cap
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
GND on the CRT
Fig. 3-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 3-4.)
Screwdriver CRT
Support
Alligator Clip
GND on the CRT

Fig. 3-1
2. Flip up the sides of the Rubber Cap in the direction of the

arrow and remove one side of the support. Fig. 3-4
4. Insert one end of the Anode Support into the anode button,
Rubber Cap then the other as shown in Fig. 3-5.
CRT
Support
Fig. 3-2
Support
CRT
Fig. 3-5
5. Confirm that the Support is securely connected.

6. Put on the Rubber Cap without moving any parts.
B3-1

4. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 4-3.)
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Some ICs on the PCB are affixed with glue, so be
Package IC to protect other parts from any damage. careful not to break or damage the foil of each IC
(Refer to Fig. 4-1.) leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within Blower type IC
10 mm distance from IC leads. desoldering
machine
Masking Tape IC
(Cotton Tape)
Tweezers
Fig. 4-1
IC
Fig. 4-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 4-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth 5. Absorb the solder left on the pattern using the Braided
directions force on the IC, until IC can move back and Shield Wire. (Refer to Fig. 4-4.)
forth easily after desoldering the IC leads completely. NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine
Braided Shield Wire
Soldering Iron
IC
IC pattern Fig. 4-4
Fig. 4-2
B4-1

INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-
1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 4-8.)
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
Thin-tip Soldering Iron IC
Soldering Iron
Fig. 4-8
5. Finally, confirm the soldering status on four sides of the

Solder temporarily Solder temporarily
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
Fig. 4-5 position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
2. Supply the solder from the upper position of IC leads NOTE
sliding to the lower position of the IC leads.
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
Solder Soldering Iron
IC Supply soldering
from upper position
to lower position
Fig. 4-6
3. Absorb the solder left on the lead using the Braided

Shield Wire. (Refer to Fig. 4-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 4-7
B4-2

KEY TO ABBREVIATIONS
A A/C : Audio/Control H.SW : Head Switch
ACC : Automatic Color Control Hz : Hertz
AE : Audio Erase I IC : Integrated Circuit
AFC : Automatic Frequency Control IF : Intermediate Frequency
AFT : Automatic Fine Tuning IND : Indicator
AFT DET : Automatic Fine Tuning Detect INV : Inverter
AGC : Automatic Gain Control K KIL : Killer
AMP : Amplifier L L : Left
ANT : Antenna LED : Light Emitting Diode
A.PB : Audio Playback LIMIT AMP : Limiter Amplifier
APC : Automatic Phase Control LM, LDM : Loading Motor
ASS'Y : Assembly LP : Long Play
AT : All Time L.P.F : Low Pass Filter
AUTO : Automatic LUMI. : Luminance
A/V : Audio/Video M M : Motor
B BGP : Burst Gate Pulse MAX : Maximum
BOT : Beginning of Tape MINI : Minimum
BPF : Bandpass Filter MIX : Mixer, mixing
BRAKE SOL : Brake Solenoid MM : Monostable Multivibrator
BUFF : Buffer MOD : Modulator, Modulation
B/W : Black and White MPX : Multiplexer, Multiplex
C C : Capacitance, Collector MS SW : Mecha State Switch
CASE : Cassette N NC : Non Connection
CAP : Capstan NR : Noise Reduction
CARR : Carrier O OSC : Oscillator
CH : Channel OPE : Operation
CLK : Clock P PB : Playback
CLOCK (SY-SE) : Clock (Syscon to Servo) PB CTL : Playback Control
COMB : Combination, Comb Filter PB-C : Playback-Chrominance
CONV : Converter PB-Y : Playback-Luminance
CPM : Capstan Motor PCB : Printed Circuit Board
CTL : Control P. CON : Power Control
CYL : Cylinder PD : Phase Detector
CYL-M : Cylinder-Motor PG : Pulse Generator
CYL SENS : Cylinder-Sensor P-P : Peak-to Peak
D DATA (SY-CE) : Data (Syscon to Servo) R R : Right
dB : Decibel REC : Recording
DC : Direct Current REC-C : Recording-Chrominance
DD Unit : Direct Drive Motor Unit REC-Y : Recording-Luminance
DEMOD : Demodulator REEL BRK : Reel Brake
DET : Detector REEL S : Reel Sensor
DEV : Deviation REF : Reference
E E : Emitter REG : Regulated, Regulator
EF : Emitter Follower REW : Rewind
EMPH : Emphasis REV, RVS : Reverse
ENC : Encoder RF : Radio Frequency
ENV : Envelope RMC : Remote Control
EOT : End of Tape RY : Relay
EQ : Equalizer S S. CLK : Serial Clock
EXT : External S. COM : Sensor Common
F F : Fuse S. DATA : Serial Data
FBC : Feed Back Clamp SEG : Segment
FE : Full Erase SEL : Select, Selector
FF : Fast Forward, Flipflop SENS : Sensor
FG : Frequency Generator SER : Search Mode
FL SW : Front Loading Switch SI : Serial Input
FM : Frequency Modulation SIF : Sound Intermediate Frequency
FSC : Frequency Sub Carrier SO : Serial Output
FWD : Forward SOL : Solenoid
G GEN : Generator SP : Standard Play
GND : Ground STB : Serial Strobe
H H.P.F : High Pass Filter SW : Switch
C1-1

KEY TO ABBREVIATIONS
S SYNC : Synchronization
SYNC SEP : Sync Separator, Separation
T TR : Transistor
TRAC : Tracking
TRICK PB : Trick Playback
TP : Test Point
U UNREG : Unregulated
V V : Volt
VCO : Voltage Controlled Oscillator
VIF : Video Intermediate Frequency
VP : Vertical Pulse, Voltage Display
V.PB : Video Playback
VR : Variable Resistor
V.REC : Video Recording
VSF : Visual Search Fast Forward
VSR : Visual Search Rewind
VSS : Voltage Super Source
V-SYNC : Vertical-Synchronization
VT : Voltage Tuning
X X'TAL : Crystal
Y Y/C : Luminance/Chrominance
C1-2

SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and
remocon key simultaneously.
The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug
AC cord and allow at least 5 seconds before Power On.
Set Key Remocon Key Operations
VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of the factory.

VOL. (-) MIN 1
NOTE: Do not use this for the normal servicing.
Horizontal position adjustment of OSD.

VOL. (-) MIN 2 NOTE: Also can be adjusted by using the Adjustment MENU.
Refer to the "ELECTRICAL ADJUSTMENT" (OSD HORIZONTAL).
Adjust the PG SHIFTER automatically.

VOL. (-) MIN 3
Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).
Adjust the PG SHIFTER manually.

VOL. (-) MIN 4
Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).
Adjusting of the Tracking to the center position.

VOL. (-) MIN 5 NOTE: Also can be adjusted by pressing the ATR button for more than 2 seconds
during PLAY.
POWER ON total hours and PLAY/REC total hours are displayed on the screen.
Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS" (CONFIRMATION
OF HOURS USED).
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Writing of EEPROM initial data.

VOL. (-) MIN 8
NOTE: Do not use this for the normal servicing.
Display of the Adjustment MENU on the screen.

VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
Method Operations
Press the ATR button on the Adjusting of the Tracking to the center position.
remote control for more than Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL
2 seconds during PLAY. ADJUSTMENT" (PG SHIFTER).
Make the short circuit between

The EOT/BOT/Reel sensor do not work at this moment.
the test point of SERVICE and
Refer to the "PREPARATION FOR SERVICING"
the GND.
C2-1

PREVENTIVE CHECKS AND SERVICE INTERVALS
The following standard table depends on environmental conditions and usage. Unless maintenance is properly
carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts.
Also, long term storage or misuse may cause transformation and aging of rubber parts.
Time 500 1,000 1,500 2,000 3,000

hours hours hours hours hours Notes
Parts Name
Audio Control Head
Clean those parts in
Full Erase Head contact with the tape.
(Recorder only)
Capstan Belt Clean the rubber, and parts
Pinch Roller which the rubber touches.
Capstan DD Unit
Loading Motor
Tension Band
Capstan Shaft
Tape Running Replace when rolling
Guide Post becomes abnormal.
Cylinder Unit Clean the Head
: Clean
: Replace
CONFIRMATION OF HOURS USED

POWER ON total hours and PLAY/REC total hours can be checked on the screen.
Total hours are displayed in 16 system of notation.
NOTE: The confirmation of using hours will not be possible if clock has been set. To reset clock, either unplug
AC cord and allow at least 5 seconds before Power On.
1. Set the VOLUME to minimum.
2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously.
3. After the confirmation of using hours, turn off the power.
INIT 00 83 Initial setting content of MEMORY IC.
POWER ON 0010 POWER ON total hours.

PLAY/REC 0003 PLAY/REC total hours.
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1

PREVENTIVE CHECKS AND SERVICE INTERVALS
CLEANING
NOTE 2. TAPE RUNNING SYSTEM
After cleaning the heads with isopropyl alcohol, do not When cleaning the tape transport system, use the
run a tape until the heads dry completely. If the heads gauze moistened with isopropyl alcohol.
are not completely dry and alcohol gets on the tape, 3. CYLINDER
damage may occur.
Wrap a piece of chamois around your finger. Dip it in
1. AUDIO CONTROL HEAD isopropyl alcohol. Hold it to the cylinder head softly.
Clean the Audio Control Head with the cotton stick Turn the cylinder head counterclockwise to clean it (in
soaked by alcohol. Clean the full erase head in the the direction of the arrow). (Refer to the figure below.)
same manner. (Refer to the figure below.) NOTE
Do not exert force against the cylinder head. Do not move
the chamois upward or downward on the head.
Use the chamois one by one.
Audio Control Head

Cylinder Head
C3-2

WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow
at least 5 seconds before Power On.
INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00 88 0A 62 63 43 14 34 09 51 38 30 66 00 40 00 10
10 B2 9A 92 93 00 00 00 15 08 00 A9 0F 94 3E 06 04
20 06 29 01 17 10 60 32 3A DA D7 10 15 20 25 26 27
30 28 29 2A 2C 2E 30 32 34 36 38 3A 3C 3E 40 41 42
40 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52
50 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62
60 63 64 66 69 6D 74 79 7C 7E 7F --- --- --- --- --- ---
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.

2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously.
ADDRESS and DATA should appear as FIG 1.
ADDRESS DATA
INIT 00 83
POWER ON 0010
PLAY/REC 0003
Fig. 1
3. ADDRESS is now selected and should "blink". Using the PLAY or STOP button on the remote, step through the
ADDRESS until required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using PLAY or STOP until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
C4-1

SERVICING FIXTURES AND TOOLS
(For 2 heads model) (For 4 heads model) JG002B Adapter JG005 Post Adjustment
VHS Alignment Tape VHS Alignment Tape JG002E Dial Torque Gauge Screwdriver
JG001 (VN 2 S-LI6 3 ) JG001B (VN 1 S-LI6 3 ) (10~90gf•cm) Part No. SV-TG0-030-000
JG001A (VN 2 S-CO13 ) JG001I (VN 1 S-CO13 )
JG002F (60~600gf•cm) (small)
JG001Q (VN 2 S-LI6 3 H) JG001P (VN 1 S-LI6 3 H)
JG001T (VN 2 S-X6 3 ) JG001S (VN 1 S-X6 3 )
JG153 X Value Adjustment JG022 Master Plane JG024A Reel Disk Height JG100A Torque Tape
Screwdriver Adjustment Jig (VHT-063)
JG154 Cable Tentelometer
Ref. No. Part No. Parts Name Remarks

JG001 APJG001000 VHS Alignment Tape (For 2 heads model) Monoscope, 6KHz
JG001A APJG001A00 VHS Alignment Tape (For 2 heads model) Color Bar, 1KHz
JG001Q APJG001Q00 VHS Alignment Tape (For 2 heads model) Hi-Fi Audio
JG001T APJG001T00 VHS Alignment Tape (For 2 heads model) X Value Adjustment
JG001B APJG001B00 VHS Alignment Tape (For 4 heads model) Monoscope, 6KHz
JG001I APJG001I00 VHS Alignment Tape (For 4 heads model) Color Bar, 1KHz
JG001P APJG001P00 VHS Alignment Tape (For 4 heads model) Hi-Fi Audio
JG001S APJG001S00 VHS Alignment Tape (For 4 heads model) X Value Adjustment
JG002B APJG002B00 Adapter VSR Torque, Brake Torque (S Reel/T Reel Ass'y)
JG002E APJG002E00 Dial Torque Gauge (10~90gf•cm) Brake Torque (T Reel Ass'y)
JG002F APJG002F00 Dial Torque Gauge (60~600gf•cm) VSR Torque, Brake Torque (S Reel)
JG005 APJG005000 Post Adjustment Screwdriver Guide Roller Adjustment
JG153 APJG153000 X Value Adjustment Screwdriver X Value Adjustment
JG022 APJG022000 Master Plane Reel Disk Height Adjustment
JG024A APJG024A00 Reel Disk Height Adjustment Jig Reel Disk Height Adjustment
JG100A APJG100A00 Torque Tape (VHT-063) Playback Torque, Back Tension Torque During Playback
JG154 APJG154000 Cable Used to connect the test point of SERVICE and GROUND
PREPARATION FOR SERVICING

How to use the Servicing Fixture
1. Unplug the connector CP757 and CP351, then remove the TV/VCR Block from the set.
2. Remove the Operation PCB from the set, then connect it with the Syscon PCB.
If necessary, connect CP351. (Front A/V Jack Input Terminal)
3. Short circuit between TP1001 and Ground with the cable JG154.
(Refer to MAJOR COMPONENTS LOCATION GUIDE)
4. The EOT, BOT and Reel Sensor do not work at this moment.
At that time, the STOP/EJECT button is available to insert and eject the Cassette Tape.
C5-1

MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION
POST POSITION
Read the following NOTES before starting work.
1. Set to the PLAY mode.
• Place an object which weighs between 450g~500g on 2. Adjust the adjusting parts for the Tension Arm position
the Cassette Tape to keep it steady when you want to so that the Tension Arm top is within the standard line of
make the tape run without the Cassette Holder. (Do not Main Chassis.
place an object which weighs over 500g.) 3. While turning the S Reel clockwise, confirm that the
• When you activate the deck without the Cassette edge of the Tension Arm is located in the position
Holder, short circuit between TP1001 and GND. (Refer described above.
to ELECTRICAL ADJUSTMENT PARTS LOCATION
GUIDE) In this condition the BOT/EOT/Reel Sensor will Standard line of Main Chassis
not function.
1-1: CONFIRMATION AND ADJUSTMENT OF REEL

DISK HEIGHT
Tension Arm
1. Turn on the power and set to the STOP mode.
2. Set the master plane (JG022) and reel disk height
adjustment jig (JG024A) on the mechanism framework,
taking care not to scratch the drum, as shown in Fig. 1-
0.5mm (Adjusting range)
1-A.
Fig. 1-2-A
3. While turning the reel and confirm the following points.
Check if the surface "A" of reel disk is lower than the
surface "B" of reel disk height adjustment jig (JG024A) Adjusting parts for the
Tension Arm position
and is higher than the surface "C". If it is not passed,
place the height adjustment washers and adjust to
10(+2, -0)mm.
4. Adjust the other reel in the same way. Tension Band
Master Plane (JG022)
Reel Disk Height Adjustment Jig The Tension Arm top will The Tension Arm top will
(JG024A) move to the inside direction move to the outside direction
of the Main Chassis. of the Main Chassis.
Bend
Fig. 1-2-B
1-3: CONFIRMATION OF PLAYBACK TORQUE AND

BACK TENSION TORQUE DURING PLAYBACK
1. Load a video tape (T-120) recorded in standard speed
mode. Set the unit to the PLAY mode.
2. Install the tentelometer as shown in Fig. 1-3. Confirm that
the meter indicates 20 ± 2gf in the beginning of playback.
Fig. 1-1-A
• USING A CASSETTE TYPE TORQUE TAPE (JG100A)
1. After confirmation and adjustment of Tension Post
Reel Disk Height
Reel Disk Adjustment Jig position (Refer to item 1-2), load the cassette type
(JG024A) torque tape (JG100A) and set to the PLAY mode.
2. Confirm that the right meter of the torque tape indicates
Master Plane (JG022)
(B) 50~90gf•cm during playback in SP mode.
3. Confirm that the left meter of the torque tape indicates
25~40gf•cm during playback in SP mode.
10(+0.2, -0)mm Tentelometer

(C)
Video Tape
(A)
Height Adjustment
Washer
2.6x4.7xT0.13
2.6X4.7xT0.25 Fig. 1-1-B P1 Post Guide Roller
Fig. 1-3
D1-1

1-4: CONFIRMATION OF VSR TORQUE NOTE
1. Install the Torque Gauge (JG002F) and Adapter (JG002B) If the torque is out of the range, replace the following
on the S Reel. Set to the Picture Search (Rewind) mode. parts.
(Refer to Fig.1-4-B)
2. Then, confirm that it indicates 120~180gf•cm. Check item Replacement Part
NOTE 1-4 Idler Ass'y/Clutch Ass'y
1-5 S Reel side: S Reel/Tension Band/Tension
Install the Torque Gauge on the reel disk firmly. Press the
Connect/Tension Arm Ass'y
REW button to turn the reel disk.
T Reel side: T Reel/T Brake Band//T Brake
Spring/T Brake Arm
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) (Refer to Fig. 1-4-B)
1. Once set to the Fast Forward mode then set to the Stop
2. CONFIRMATION AND ADJUSTMENT
mode. While, unplug the AC cord when the Pinch Roller OF TAPE RUNNING MECHANISM
Block is on the position of Fig. 1-4-A. Tape Running Mechanism is adjusted precisely at the
2. Move the Idler Ass'y from the S Reel. factory. Adjustment is not necessary as usual. When you
3. Install the Torque Gauge (JG002F) and Adapter replace the parts of the tape running mechanism because
(JG002B) on the S Reel. Turn the Torque Gauge of long term usage or failure, the confirmation and
(JG002F) clockwise. adjustment are necessary.
4. Then, confirm that it indicates 60~100gf•cm.
(T Reel Brake) (Refer to Fig. 1-4-B) 2-1: GUIDE ROLLER
1. Once set to the Fast Forward mode then set to the Stop 1. Playback the VHS Alignment Tape (JG001 or JG001B).
mode. While, unplug the AC cord when the Pinch Roller (Refer to SERVICING FIXTURE AND TOOLS)
Block is on the position of Fig. 1-4-A. 2. Connect CH-1 of the oscilloscope to TP4001 (Envelope)
2. Move the Idler Ass'y from the T Reel. and CH-2 to TP1002 (SW Pulse).
3. Install the Torque Gauge (JG002E) and Adapter 3. Press and hold the Tracking-Auto button on the remote
(JG002B) on the T reel. Turn the Torque Gauge control more than 2 seconds to set tracking to center.
(JG002E) counterclockwise. 4. Trigger with SW Pulse and observe the envelope. (Refer
4. Then, confirm that it indicates 30~50gf•cm. to Fig. 2-1-A)
5. When observing the envelope, adjust the Adjusting
The position at FF mode. Driver (JG005) slightly until the envelope will be flat.
Pinch Roller Block Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
Stop at this position.
6. Adjust so that the A : B ratio is better than 3 : 2 as shown
in Fig. 2-1-B, even if you press the Tracking Button to
Cassette move the envelope (The envelope waveform will begin to
Opener
The position at decrease when you press the Tracking Button).
STOP mode.
7. Adjust the PG shifter during playback.
Capstan DD Unit (Refer to the ELECTRICAL ADJUSTMENTS)
NOTE
Cassette Holder Ass'y
After adjustment, confirm and adjust A/C head.
Fig. 1-4-A
(Refer to item 2-2)
Torque Gauge/Adapter
(JG002F/JG002B) CH-1
Envelope
(TP4001)
CH-1 CH-2
Torque Gauge/Adapter Track Track
(JG002E/JG002B)
CH-2
SW Pulse (TP1002)
Fig. 2-1-A
Entrance Exit
S Reel
Max A B Max
T Reel
Fig. 1-4-B
A:B≥3:2
Fig. 2-1-B
D1-2

2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ 2-3: TAPE RUNNING ADJUSTMENT
CONTROL HEAD (X VALUE ADJUSTMENT)
When the Tape Running Mechanism does not work well, 1. Confirm and adjust the height of the Reel Disk.
adjust the following items. (Refer to item 1-1)
2. Confirm and adjust the position of the Tension Post.
1. Playback the VHS Alignment Tape (JG001 or JG001B).
(Refer to item 1-2)
(Refer to SERVICING FIXTURE AND TOOLS)
3. Adjust the Guide Roller. (Refer to item 2-1)
2. Confirm that the reflected picture of stamp mark is
4. Confirm and adjust the Audio/Control Head.
appeared on the tape prior to P4 Post as shown in Fig.
(Refer to item 2-2)
2-2-A.
5. Connect CH-1 of the oscilloscope to TP4001, CH-2 to
a) When the reflected picture is distorted, turn the screw
TP1002 and CH-3 to HOT side of Audio Out Jack.
1 clockwise until the distortion is disappeared.
6. Playback the VHS Alignment Tape (JG001S or
b) When the reflected picture is not distorted, turn the
JG001T). (Refer to SERVICING FIXTURE AND TOOLS)
screw 1 counterclockwise until little distortion is
7. Press and hold the Tracking-Auto button on the remote
appeared, then adjust the a).
control more than 2 seconds to set tracking to center.
3. Turn the screw 2 to set the audio level to maximum.
8. Set the X Value adjustment driver (JG153) to the 4 of
4. Confirm that the bottom of the Audio/ Control Head and
Fig. 2-2-B. Adjust X value so that the envelope waveform
the bottom of the tape is shown in Fig. 2-2-C.
output becomes maximum. Check if the relation between
c) When the height is not correct, turn the screw 3 to
Audio and Envelope waveform becomes (1) or (2) of Fig.
adjust the height. Then, adjust the 1~3 again.
2-3.
Audio/Control Head
Reflected picture of Envelope

Stamp Mark
P4 Post
(1)
CH-3
Audio
(2)
Fig. 2-3
Stamp Mark 2-4: CONFIRM HI-FI AUDIO (Hi-Fi model only)

Fig. 2-2-A
1. Connect CH-1 of the oscilloscope to TP1002 and CH-2 to
Audio/Control Head the Hi-Fi Audio Out Jack.
2. Playback the VHS Alignment Tape (JG001P or JG001Q).
(Refer to SERVICING FIXTURE AND TOOLS)
3. Press and hold the Tracking-Auto button on the remote
3 1 4. Press the Tracking Up button and count number of steps
which the audio output is changed from Hi-Fi (10KHz) to
2
MONO (6KHz).
4 5. Press and hold the Tracking-Auto button on the remote
Fig. 2-2-B 6. Press the Tracking Down button and count number of
steps which the audio output is changed from Hi-Fi
(10KHz) to MONO (6KHz).
Audio/Control Head
7. If the difference are more than 3 steps, set the X Value
Tape adjustment driver (JG153) to 4 of Fig. 2-2-B. Change the
X Value and adjust it so that the value becomes within 2
steps.
0.25±0.05mm
Fig. 2-2-C
D1-3

3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
6
3
2
7
10 9 8
1. Tension Connect 6. P4 Post

2. Tension Arm 7. T Brake Spring
3. Guide Roller 8. T Reel
4. Audio/Control Head 9. S Reel
5. X value adjustment driver hole 10. Adjusting parts for the Tension Arm position
D1-4

ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS
ADJUSTMENTS (VCR SECTION)
Read and perform these adjustments when repairing the 2-1: PG SHIFTER
circuits or replacing electrical parts or PCB assemblies.
1. Connect CH-1 on the oscilloscope to TP1002 and CH-2
CAUTION to pin 4 of CP1003.
• Use an isolation transformer when performing any 2. Playback the alignment tape. (JG001A)
service on this chassis. 3. Press and hold the Tracking-Auto button on the remote
• Before removing the anode cap, discharge electricity control more than 2 seconds to set tracking to center.
because it contains high voltage. 4. Press the VOL. DOWN button on the set and the
• When removing a PCB or related component, after channel button (3) on the remote control simultaneously
unfastening or changing a wire, be sure to put the wire until the indicator REC disappears. If the indicator REC
back in its original position. disappears, adjustment is completed.
Inferior silicon grease can damage IC's and transistors. (If the above adjustments doesn't work well:)
• When replacing IC's and transistors, use only specified
silicon grease (YG6260M). 5. Press the VOL. DOWN button on the set and the
Remove all old silicon before applying new silicon. channel button (3) on the remote control simultaneously
until the indicator REC disappears.
On-Screen Display Adjustment 6. When the REC indicator is blinking, press both VOL.
DOWN button on the set and the channel button (4) on
1. Unplug the AC plug for more than 5 seconds to set the the remote control simultaneously and adjust the
clock to the non-setting state. Then, set the volume Tracking +/- button until the arising to the down of Head
level to minimum. Switching Pulse becomes 6.5 ± 0.5H.
2. Press the VOL. DOWN button on the set and the (Refer to Fig. 2-1-A, B)
Channel button (9) on the remote control simultaneously 7. Press the Tracking Auto button.
to appear the adjustment mode on the screen as shown
in Fig. 1-1.
CH-2
TV
6.5H
CH-1
Fig. 2-1-A
00 OSD 15
Fig. 1-1
3. Use the Channel UP/DOWN button or Channel button CH-2

(0-9) on the remote control to select the options shown
in Fig. 1-2.
4. Press the MENU button on the remote control to end
CH-1
the adjustments.
6.5H
NO. FUNCTION NO. FUNCTION Fig. 2-1-B

00 OSD H 13 BRIGHTNESS
01 CUT OFF 14 CONTRAST
2-2: VCO FREERUN
02 RF AGC DELAY 15 COLOR
03 VIF VCO 16 TINT 1. Place the set with Aging Test for more than 10 minutes.
04 H VCO 17 SHARPNESS 2. Receive the VHF HIGH.
05 H PHASE 18 FM LEVEL 3. Disconnect the Antenna while receiving the VHF HIGH
06 V SIZE 19 LEVEL and set to the Noise screen.
07 V SHIFT 20 SEPARATION 1 4. Once turn off the Power and turn on the Power again.
08 R DRIVE 21 SEPARATION 2 5. Approxi. 3 seconds later, input the Antenna again.
09 B DRIVE 22 TEST MONO 6. Connect the digital voltmeter between the pin 5 of
10 R CUT OFF 23 TEST STEREO CP351 and the pin 1 (GND) of CP351.
11 G CUT OFF 24 X-RAY TEST 7. Activate the adjustment mode display of Fig. 1-1 and
12 B CUT OFF press the channel button (03) on the remote control to
Fig. 1-2 select "VIF VCO".
8. Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.
9. After the 2.5V adjustment, countdown the VIF VCO step
No. by 1 step with the VOL. DOWN button.
D2-1

2-3: RF AGC 2-8: HORIZONTAL PHASE
1. Receive the VHF HIGH (63dB). 1. Receive the center cross signal from the Pattern
2. Connect the digital voltmeter between the pin 5 of Generator.
CP351 and the pin 1 (GND) of CP351. 2. Using the remote control, set the brightness and
3. Activate the adjustment mode display of Fig. 1-1 and contrast to normal position.
press the channel button (02) on the remote control to 3. Activate the adjustment mode display of Fig. 1-1 and
select "RF AGC". press the channel button (05) on the remote control to
4. Press the VOL. UP/DOWN button on the remote control select "H PHASE".
until the digital voltmeter is 2.9V ± 0.05V. 4. Press the VOL. UP/DOWN button on the remote control
until the right and left screen size of the vertical line
(TV SECTION) becomes the same.
2-4: CONSTANT VOLTAGE 2-9: VERTICAL SHIFT
1. Connect the digital voltmeter to the TP601. 1. Receive the center cross signal from the Pattern
2. Set condition is AV MODE without signal. Generator.
3. Using the remote control, set the brightness and contrast 2. Using the remote control, set the brightness and
to normal position. contrast to normal position.
4. Adjust the VR502 until the digital voltmeter is 135 ± 0.5V. 3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
2-5: CUT OFF select "V SHIFT".
1. Adjust the unit to the following settings. 4. Check if the step No. V. SHIFT is "3".
R CUT OFF=128, G CUT OFF=128, B CUT OFF=128, 5. Adjust the VR401 until the horizontal line becomes fit to
BRIGHTNESS=128, CONTRAST=100 the notch of the shadow mask.
2. Place the set with Aging Test for more than 15 minutes.
3. Set condition is AV MODE without signal. 2-10: VERTICAL SIZE
4. Using the remote control, set the brightness and
1. Receive the cross hatch signal from the Pattern
contrast to normal position.
Generator.
5. Activate the adjustment mode display of Fig. 1-1 and
select "CUT OFF".
6. Adjust the Screen Volume until a dim raster is obtained.
select "V SIZE".
2-6: WHITE BALANCE
4. Press the VOL. UP/DOWN button on the remote
NOTE: Adjust after performing CUT OFF adjustment. control until the SHIFT quantity of the OVER SCAN
1. Place the set with Aging Test for more than 15 minutes. on upside and downside becomes 10 ± 2%.
2. Receive the color bar pattern. 5. Receive a broadcast and check if the picture is normal.
contrast to normal position. 2-11: SUB BRIGHTNESS
4. Activate the adjustment mode display of Fig. 1-1 and 1. Receive the monoscope pattern. (RF Input)
press the channel button (10) on the remote control to 2. Using the remote control, set the brightness and
select "R CUT OFF". contrast to normal position.
5. Using the VOL. UP/DOWN button on the remote 3. Activate the adjustment mode display of Fig. 1-1 and
control, adjust the R CUT OFF. press the channel button (13) on the remote control to
6. Press the CH. UP/DOWN button on the remote control select "BRIGHTNESS".
to select the "R DRIVE", "B DRIVE", "G CUT OFF" or 4. Press the VOL. UP/DOWN button on the remote
"B CUT OFF". control until the white 10% is starting to be visible
7. Using the VOL. UP/DOWN button on the remote 5. Receive the monoscope pattern. (Audio Video Input)
control, adjust the R DRIVE, B DRIVE, G CUT OFF or 6. Press the INPUT SELECT button on the remote control
B CUT OFF. to set to the AV mode. Then perform the above
8. Perform the above adjustments 6 and 7 until the white adjustments 2~4.
color is looked like a white.
2-7: FOCUS
1. Receive the monoscope pattern.
3. Turn the Focus Volume fully counterclockwise once.
4. Adjust the Focus Volume until picture is distinct.
D2-2

2-12: SUB CONTRAST MANUAL
White 0%
1. Receive the color bar pattern. (RF Input)
select "CONTRAST". 100%
until the contrast STEP No. becomes "100".
5. Receive the color bar pattern. (Audio Video Input)
6. Press the AV button on the remote control to set to the
AV mode. Then perform the above adjustments 2~4.
Red Level
2-13: SUB TINT White 100%
Fig. 2-3
1. Receive the color bar pattern. (RF Input)
2. Connect the oscilloscope to TP801. 2-15: OSD HORIZONTAL
3. Using the remote control, set the brightness, contrast,
color and tint to normal position. 1. Activate the adjustment mode display of Fig. 1-1.
4. Activate the adjustment mode display of Fig. 1-1 and 2. Press the VOL. UP/DOWN button on the remote control
press the channel button (16) on the remote control to until the difference of A and B becomes minimum.
select "TINT". (Refer to Fig. 2-4)
until the section "A" becomes a straight line.
(Refer to Fig. 2-2) TV
7. Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~5.
00 OSD 15
A B Fig. 2-4
2-16: SUB SHARPNESS

"A"
select "SHARPNESS".
Fig. 2-2 2. Check if the step No. of SHARPNESS is "40".
3. Press the AV button on the remote control to set to the
AV mode. Then perform the above adjustments 1, 2.
2-14: SUB COLOR
1. Receive the color bar pattern. (RF Input) 2-17: H VCO
2. Connect the oscilloscope to TP803. 1. Activate the adjustment mode display of Fig. 1-1 and
3. Using the remote control, set the brightness, contrast, press the channel button (04) on the remote control to
color and tint to normal position. select "H VCO".
4. Activate the adjustment mode display of Fig. 1-1 and 2. Check if the step No. of H VCO is "4".
select "COLOR".
5. Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 4 scales on the screen of the oscilloscope.
until the red color level is adjusted to 110 ± 10% of the
white level. (Refer to Fig. 2-3)
8. Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~6.
D2-3

3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE
CP1003
TP1001
TP4001
TP1002
TP601
VR401 VR502
TU601
FB401
CP351
FOCUS VOLUME
SCREEN VOLUME
SYSCON PCB
TP801
TP803
J801
CRT PCB
D2-4

4. PURITY AND CONVERGENCE 4-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 4-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch pattern
terrestrial magnetism. on the center of the screen by adjusting the pair of 4
3. Turn ON the unit and demagnetize with a Degauss Coil. pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
4-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 4-1) 4-4: DYNAMIC CONVERGENCE
If the deflection yoke and magnet are in one body,
NOTE
untighten the screw for the body.
2. Receive the green raster pattern from the color bar Adjust after performing adjustments in section 4-3.
generator. 1. Adjust the differences around the screen by moving the
3. Slide the deflection yoke until it touches the funnel side deflection yoke upward/downward and right/left.
of the CRT. (Refer to Fig. 4-2-a)
4. Adjust center of screen to green, with red and blue on 2. Insert three wedges between the deflection yoke and
the sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 4-2-b)
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern RGB RGB
on the center of the screen by adjusting the pair of 4
pole magnets.
7. Combine red/blue (magenta) and green by adjusting the R
pair of 6 pole magnets. G
8. Adjust the crosshatch pattern to change to white by B
R
repeating steps 6 and 7. G
B
4-2: PURITY UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE Fig. 4-2-a
Adjust after performing adjustments in section 4-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the WEDGE WEDGE
ends are equally wide.
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching WEDGE
the screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW Fig. 4-2-b
MAGNET SCREW
6 POLE MAGNETS
4 POLE MAGNETS
PURITY MAGNETS
Fig. 4-1
D2-5

TV BLOCK DIAGRAM
V. OUTPUT IC IC401 AN5522
MICON/ SCL
OPERATION/ SDA THERMAL
IN/OUT PROTECTION
Q602, Q603 Q606
AT+12V AMP
AT+5V_BACK UP REG. REG.
AT+12V PUMP Q407
Q601 Q604, Q605 UP H-CONTROL MICON/
TU_AUDIO VCC SW H_CTL OPERATION/
Y/C/AUDIO/ AT+5V IN/OUT
CCD/ TU_VIDEO BUFFER REG. 1 2 3 5 7
HEAD AMP Y/C_AUDIO
CHROMA IC Q405 Q406
NC
IC601 M61206FP H-DRIVE H. OUTPUT
63 48 52 56 57 55 41 42 33 39 46 13 53
DY
5.7V REG OUT (FOR CPU)
POWER ON CONT
VIF APC FILTER
FM DIRECT OUT
EXT AUDIO IN
VIF VIDEO OUT
SW REG CONT
VREG VCC
IF AGC FILTER
8.7V REG OUT

IF AGC
MCU RESET
5V REG
AUDIO OUT 50
TU601 62 RF AGC OUT FB401
SDA 10 3
1 SAW FILTER 1 VIF IN 1 COL
CF601 SCL 5
4 64 VIF IN 2 +B HV
FAST BLK 27 J801
5 1 4 5 6 E180
60 R OUT 14
AFT OUT 7 ABL F F
11
G OUT 15
9 AFC S 7
B OUT 16 V801
10 HEA 11
CRT
8
E180V 6
V OUT 17
Q804
31 ACL/ABCL V PLUSE OUT 29
BLUE AMP Q608
V RAMP FEED BACK 21
CUT OFF SW P. CON+8V
Q806
CHROMA APC FILTER
RED AMP
H. PLUSE OUT
Q805
GREEN
AMP
FBP IN
X' TAL
H OUT
Q404
X-RAY SW. 35 32 12 6 7 Q609
MICON/ POWER ON
OPERATION/ Q403 TV_POWER-H
SW.
IN/OUT VD
X-RAY_TEST SW.
HD
X602
3.579545MHz OSD_BLK MICON/
OPERATION/
OSD_B IN/OUT
OSD_R
DEGAUSS COIL
TH501 OSD_G
2 2
AFT_M
Q611
1 1 SOUND AMP IC
L503
POWER FAIL
POWER_FAIL SW. IC351 AN7511
J351
D518, D520, 2 6 HEAD
D521, D530 JACK
T501
AC IN RECTIFIER CD352
8 11 8
5 SP+
F501 Q511 SP351
13 AT+12V SP– SPEAKER
Q507 FEED BACK SWITCHING
14 UNREG+8V 1 4
FEED BACK IC502 TLP621(GR)
SW. Q510 POWER_FAIL
16
SWITCHING 5 F502
+B ADJ
VR502
5V REG IC P. CON+5V
IC501 VCR_POWER-H
MICON/
KIA78R05PI TV_POWER-H OPERATION/
IN/OUT E-2
E-1 TV_A_MUTE

Y/C/AUDIO/CCD/HEAD AMP BLOCK DIAGRAM
X4001
3.579545MHz
Q4012 Q4010
BUFFER BUFFER
Y/C/AUDIO/CCD/HEAD AMP IC
IC4001
LA71201M-N-MPB
50 49 41 43 38 37
4FSC VSS
VX01 PLL
NC 67 P L REC REC
H APC APC
NC 66 R 3.58M
BPF2
62 HA R P
GND
CP4001 CLAMP AUTO-BIAS
Main
1 65 P CONV
53 Y/C_CLK
2 SP-CH2 (L) 72 P H CCD SERAIL MICON/
CYL 54 Y/C_DATA OPERATION/
L DECODER
3 SP_COM IN/OUT
B-UP 55 Y/C_CS
4 SP-CH1 (R) 73 AGC
R AMP
C-LPF
74 P
OUT
VCA
36
ACC 3.58M
DET 39
TV VD BPF1 VIDEO SYNC C-ROT
AGC SEP RF-SW IN 57 H. SW
AUDIO 58 VCR_A_MUTE
9 REC AMP MUTE HA SW
NYR/COMB
7 QV-QH ENV DET 59 ENV. DET
CP4003 V.REC_ST-H
1 60B MICON/
FE HEAD 1 FE HEAD (HOT) R ALC 2 OPERATION/
8 LINE LPF 3 1 2 3
2 FE HEAD (GND) AMP Q4009 IN/OUT
EQ P SYNC 24 DUMMY_V. SYNC
AUTO BIAS AMP SEP Q4007
26 BUFFER SD_VIDEO
6 PB.EE MUTE
25 SYNC SD_SYNC
IN
Q4011
P. CON+5V BUFFER 11 3 4 5 2 10 80 76 32 30 28
NC
CP4002 COIL, BIAS OSC
6 AUDIO PB T4001 Q4005
5 AUDIO REC BIAS CTL TU_VIDEO
5 2
HEAD 4 CTL+ TU_AUDIO TV
AUDIO
CONTROL 3 CTL- 6 3
Q4006 Y/C_AUDIO
2 AE HEAD(-) BIAS OSC P. CON + 5V
1 AE HEAD(+) 4 1
Q4001, Q4002 Q4003

FRONT_AUDIO
AUDIO PB SW SW
FRONT_VIDEO MICON/
OPERATION/
CTL+ IN/OUT
CTL-
E-3 E-4

MICON/OPERATION/IN/OUT BLOCK DIAGRAM
TIMER SYSCON MICON IC
SW1001 IC1001 OEC7071A
SYSTEM RESET IC
RESET-L 34 1 OUT IC1003
50 TAB SW R3111N311A/C-TR
POWER FAIL2
AT+5.6V
POWER_FAIL_L 85
P. CON+5V 1 4 1 MSSEN-A
X-OUT(12MHz) 39 Q1023
MS_SEN A X1001 J701
2 3 Q1009 12MHz AUDIO L
X-IN(12MHz) 38 X_RAY_SW
3 4 FRONT_VIDEO
1 4 2 MSSEN-B XC-OUT(32KHz) 36
X1002
MS_SEN B 32.768KHz 1 2 FRONT_AUDIO
Q1003 XC-IN(32MHz) 35
2 3
VIDEO
CTL+ 95 CTL+
1 3 80 REEL-T CTL- 94 CTL-
REEL SENS. 66
Q1005 V-REC-START-H V. REC_ST_H
2 4 Y/C/AUDIO/CCD/
CVIN 56 SD_VIDEO HEAD AMP
H_CONTROL 24 H_CONTROL SD_SYNC

VIDEO-H. SW 18 H. SW
TV X-RAY_TEST 41 X-RAY_TEST
SDATA 68 Y/C_DATA
VCR_POWER_H 27 VCR-POWER
SCLK 70 Y/C_CLK
CP1004 12 CAP-LIMIT
1 CAP_FG CS 69 Y/C_CS
76 CAP-PWM
CAPSTAN 4 CAP/M F/R VIDEO ENV 6 ENV_DET
DD UNIT 5 I LIMIT 87 CAP-FG
11 CAP-FWD VCR_A_MUTE 81 VCR_A_MUTE
9 CAP_CTL
10 IIC-DATA1 72 5 SDA EEP ROM IC
LDM_CTL 20 LDM CTL IC1099
11 CTL_FG/PG IIC-CLK1 71 6 SCL S-24C04BDP-LA
90 DRUM FG/PG
12 CYL_CTL X_RAY
77 DRUM-PWM CTL AMP-OUT 97 Q1004
FF/REW_SW SDA
FF/REW-L 73 SCL
R 64 OSD_R
G 63 OSD_G
Y/C/AUDIO/CCD/ B 62 OSD_B
DUMMY_V. SYNC 13 DUMMY-V.SYNC TV
HEAD AMP
AFT(MONI) 7 AFT_M
OSD OUT1 60 OSD_BLK
V-SYNC 59 VD
H/C-SYNC 58 HD
TV_A_MUTE 82 TV_A_MUTE
Q1013
TV_POWER_H
AT+5.6V EOT SENSOR 3 EOT KEY 1 9
D1003 Q1024
POWER REC/OTR STOP/EJECT PLAY FF/CUE REW/REV
LED DRIVER 61 CENTER LED TV-POWER 28 ON/OFF
KEY 2 10
OS753
Q1011
1 2 3 CH DOWN CH UP VOL. UP VOL. DOWN
BOT SENSOR 4 BOT
REMOCON-IN 14
Q1007
REC LED 30 REC LED SW AT+5V
(AI)
REC/OTR T-REC
D793 D791
Q1008
T-REC LED 29 ON TIM/T-REC
LED SW(TO)
E-5 E-6

OPERATION
SOLDER SIDE
SW751
SW799 SW794 SW792 SW793 SW795

W006
SW797
R351
J351
W005
W004
W003
W007
J701_1
R776_1
R775_1
W812
W009
W805 C382 R777_1

SW791 R772_1 R773_1
W811 R774_1 R766
R754_2
W001
R793_2
R771_1
W814
W008
R350_1 OS753
W002
W815 SW798
SW796 R778_1
CD352
C755_1
CD757 CD351_1
D793
D791
F-1 F-2

Service Manual: DBVT1341 Series A

Uploaded by

Copyright:

Available Formats

Service Manual: DBVT1341 Series A

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: DBVT1341 Series A

Uploaded by

Copyright:

Available Formats

DBVT1341 Series A

Design and specifications are subject to change without notice.

Downloaded from www.Manualslib.com manuals search engine

MFR’S VERSION IC4001

Please file this revision with the original version.

Downloaded from www.Manualslib.com manuals search engine

MFR'S INCORRECT CORRECT

ELECTRICAL REPLACEMENT PARTS LIST

MFR'S VERSION A MFR'S VERSION B

IC4001 I03F3200M0 IC LA71200M-MPB I03F301MN0 IC LA71201M-N-MPB

SYSCON PCB's are interchangeable.

PRINTED CIRCUIT BOREDS

ADD W261 ADD R1085

Downloaded from www.Manualslib.com manuals search engine

4.7K FROM/TO Y/C/A/H.AMP

C1080 1.9 W919 Y/C_CS

VCO IN VREG R1044

C1069 0 3.3K R1033 C1062

X_RAY 0.2 X_RAY_SW 1K 1 B

0.0022 B W810 CTL+

11.5 0 71 IIC-CLK1 5.2

RF X IN R1008 C1013 11 5.2 2.6

W OUT X OUT 13 12 2.0 0 HD

1K 1/4W AMP-VREFOUT VSS C-RESET

5 C1018 50V4.7 KA 12MHz

R1012 C1019 C1026

R1013 560 C1049 22P CH

CTL AMP-OUT RESET-L AT+5V_BACKUP

Q1013 2.5 5.2

PNA2604M010R 10 E/V_MASK AT+5V

5.1 4.8 VCR_POWER_H

SW1001 9 0.0022 B IIC_OFF

H.AMP_SW1 H.SW TV_POWER_H

FROM/TO SOUND AMP

FROM/TO MICRO MOTOR TV_POWER_H

1 U-OUT FROM/TO DEFLECTION

1 GND 2SC2412K 1 2 OUT IN GND

CAP_FG Q1003 REEL SENS

CAP_F/R RPI-352Q01R Q1005

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

110 726000A023 SHEET,CRT SERVICEMAN

120 723000A823 FILM,DECORATION

201 8117540B04 SCREW,TAPPING(B0) TRUSS 4x20

210 8109630802 SCREW,TAP TITE(B) BRAZIER 3x8

--- 791WHAA016 LAMIFILM BAG

Downloaded from www.Manualslib.com manuals search engine

320 85OP900739 LOCKER,R

330 85OP400490 LEVER,TENSION

340 85OP600582 GEAR,JOINT

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Y/C/AUDIO/CCD/HEAD AMP SCHEMATIC DIAGRAM

0305 BPF1 50V 4.7 KA TU_VIDEO

PRE GND Sub P R R 2.0