Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
50 views

Gas Turbine Engine Components 4.1 Inlets

The document describes the main components of a gas turbine engine: 1) Inlets slow incoming air and increase pressure through compression. Subsonic inlets use divergent ducts while supersonic inlets use oblique shock waves. 2) Compressors, like centrifugal and axial types, increase air pressure before combustion. 3) Combustors mix and burn fuel with compressed air, delivering hot gases to turbines. 4) Turbines extract energy from expanding gases and power the compressor through a shaft. Impulse turbines alter gas velocity while reaction turbines alter direction and pressure.

Uploaded by

mino
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
50 views

Gas Turbine Engine Components 4.1 Inlets

The document describes the main components of a gas turbine engine: 1) Inlets slow incoming air and increase pressure through compression. Subsonic inlets use divergent ducts while supersonic inlets use oblique shock waves. 2) Compressors, like centrifugal and axial types, increase air pressure before combustion. 3) Combustors mix and burn fuel with compressed air, delivering hot gases to turbines. 4) Turbines extract energy from expanding gases and power the compressor through a shaft. Impulse turbines alter gas velocity while reaction turbines alter direction and pressure.

Uploaded by

mino
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Lecture 4

Gas Turbine Engine Components

4.1 Inlets
An inlet reduces the entering air velocity to a level suitable for the
compressor. The air velocity is reduced by a compression process that increases the
air pressure. The operation and design of the inlet are described in terms of the
efficiency of the compression process, the external drag of the inlet, and the mass
flow into the inlet. The design and operation of the inlet depend on whether the air
entering the duct is subsonic or supersonic.

a) Subsonic inlet. The subsonic inlet can be a divergent duct. This duct is
satisfactory until the Match number becomes greater than 1, at which time a shock
wave occurs at the mouth and the compression process becomes inefficient. The
subsonic divergent duct operates best at one velocity (design point), and at other
velocities, the compression process is less efficient and the external drag is greater.
The airflow patterns for the subsonic inlet are shown in Fig. 4.1.

Fig. 4.1 Subsonic inlet flow patterns.

b) Supersonic inlet. Because shock waves will occur in supersonic flow, the
geometry of supersonic inlets is designed to obtain the most efficient compression
with a minimum of weight. If the velocity is reduced from a supersonic speed to a
subsonic speed with one normal shock wave, the compression process is relatively
inefficient. If several oblique shock waves are employed to reduce the velocity, the
compression process is more efficient. If the geometry is designed to be variable,
the inlet operates more efficiently over a range of Mach numbers. Types of
supersonic inlets are shown in Fig. 4.2.

1
Fig. 4.2 Types of supersonic inlets.

4.2 Compressors.
The function of the compressor is to increase the pressure of the incoming air
so that the combustion process and the power extraction process after combustion
can be carried out more efficiently. By increasing the pressure of the air, the
volume of the air is reduced, which means that the combustion of the fuel/air
mixture will occur in a smaller volume.
There are three main types of compressors:
a) Centrifugal compressor. The compressor consists of three main parts: an
impeller, a diffuser, and a compressor manifold. Air enters the compressor near the
hub of the impeller and is then compressed by the rotational motion of the
impeller. The compression occurs by first increasing the velocity of the air
(through rotation) and then diffusing the air where the velocity decreases and the
pressure increases. The diffuser also straightens the flow, and the manifold serves
as a collector to feed the air into the combustor. A typical single-stage centrifugal
compressor is shown in Fig. 4.3.

Fig. 4.3 Single-stage centrifugal compressor.


2
b) Axial compressor. An axial compressor is shown in Fig. 4.4. The air in an
axial compressor flows in an axial direction through a series of rotating rotor
blades and stationary stator vanes that are concentric with the axis of rotation. Each
set of rotor blades and stator vanes is known as a stage. The flow path in an axial
compressor decreases in the cross-sectional area in the direction of flow. The
decrease of area is in proportion to the increased density of the air as the
compression progresses from stage to stage.

Fig. 4.4 Multistage axial compressor.

c) Axial - Centrifugal Compressor. This type is a combination of axial and


centrifugal compressor stages. It is normally consists of a number of axial stages
followed by a centrifugal stags, as shown in Fig. 4.5. It is suitable for small
airflow type of engines (helicopter and small turbo-prop engines).

Fig. 4.5 Axial - Centrifugal Compressor.

4.3 Combustor or Main Burner.


The combustor is designed to burn a mixture of fuel and air and to deliver the
resulting gases to the turbine at a uniform temperature. The gas temperature must
not exceed the allowable structural temperature of the turbine. A schematic of a
combustor is shown in Fig. 4.6. The ratio of total air to fuel varies among the
different types of engines from 30 to 60 parts of air to 1 part of fuel by weight. The

3
average ratio in new engine designs is about 40:1, but only 15 parts are used for
burning.

Fig. 4.6 Schematic diagram of a combustor.

Combustion chambers may be of the can, the annular, or the can-annular


type, as shown in Fig. 4.7.

Fig. 4.7 The main types of combustion chambers.

4
4.4 Turbines.
The turbine extracts kinetic energy from the expanding gases that flow from
the combustion chamber. The kinetic energy is converted to shaft horsepower to
drive the compressor and the accessories. Nearly three-fourths of all the energy
available from the products of combustion is required to drive the compressor. The
axial-flow turbine consists of a turbine wheel rotor and a set of stationary vanes
stator, as shown in Fig. 4.8.

Fig. 4.8 Axial-flow turbine components.

Like the axial compressor, the axial turbine is usually multistaged. There are
generally fewer turbine stages than compressor stages. The result is that one stage
of turbine can power many compressor stages.
There are two basic types of axial turbines (see Fig. 4.9):
a) Impulse turbine. In the impulse type, the relative discharge velocity of the
rotor is the same as the relative inlet velocity because there is no net change in
pressure between the rotor inlet and rotor exit. The stator nozzles of the impulse
turbine are shaped to form passages that increase the velocity and reduce the
pressure of the escaping gases.
b) Reaction turbine. In the reaction turbine, the relative discharge velocity
of the rotor increases and the pressure decreases in the passages between rotor
blades. The stator nozzle passages of the reaction turbine merely alter the direction
of the flow.

5
Fig. 4.9 Impulse and reaction stages.

4.5 Exhaust Nozzles.


The purpose of the exhaust nozzle is to increase the velocity of the exhaust
gas before discharge from the nozzle and to collect and straighten gas flow from
the turbine. The nozzle supplies a high exit velocity by expanding the exhaust gas
in an expansion process that requires a decrease in pressure. The two basic types of
nozzles used in jet engines are:
a) Convergent nozzle. The convergent nozzle is a simple convergent duct, as
shown in Fig. 4.10. The convergent nozzle has generally been used in low-thrust
engines for subsonic aircraft.

Fig. 4.10 Convergent exhaust nozzle.

b) Convergent-divergent nozzle. The convergent-divergent nozzle can be a


convergent duct followed by a divergent duct (Fig. 4.11). Where the cross-
6
sectional area of the duct is a minimum, the nozzle is said to have a throat at that
position. Most convergent-divergent nozzles used in supersonic aircraft are not
simple ducts, but incorporate variable geometry and other aerodynamic features.

Fig. 4.11 Convergent-divergent nozzle.

You might also like