SECTION 03 55 11 Gypsum Concrete Floor Decks

07-11
SECTION 03 55 11
GYPSUM CONCRETE FLOOR DECKS
SPEC WRITER NOTE:

1. Delete between // ____// if not
applicable to project. Also delete any
other item or paragraph in the section
and renumber the paragraphs.
2. This is a sole source system. Prior
approval for its use is required.
3. Insure details show system.
PART 1 - GENERAL
1.1 DESCRIPTION
A. Section specifies gypsum plank systems for fire rated interstitial decks
//.
B. Optional system for interstitial decks. //
1.2 RELATED WORK
A. Steel Framing: Section 05 12 00, STRUCTURAL STEEL FRAMING
B. Sealer for interstitial floor and floor paint for traffic area in
interstitial space: Section 09 91 00, PAINTING.
1.3 QUALITY CONTROL
A. Work performed by experienced, qualified installers approved by
manufacturer of gypsum plank.
B. Gypsum materials products of one manufacturer.
1.4 SUBMITTALS
A. Submit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA
AND SAMPLES.
B. Fire Tests: Fire tests, data and certifications substantiating that
Gypsum Plank Decking complies with fire rating requirements.
C. Shop Drawings: Show typical plank layouts, perimeter and framed opening
supports and details of construction, installation, fastenings and
grouting.
D. Manufacturer's Literature and Data: Each item specified.
E. Load tables for sub-purlins.
1.5 DELIVERY AND STORAGE
A. Deliver materials in original packages, containers, or bundles bearing
brand name and name of manufacturer.
B. Store materials in a manner that prevents damage before use. When stored
under tarpaulins, provide ventilation to prevent moisture accumulation
under tarpaulin.
03 55 11 - 1
07-11
C. Store gypsum planks flat and off ground. Handle and stack in a manner
to prevent damage to face, ends, and edges and keep dry until used.
D. Store gypsum concrete off ground and keep dry until used.
1.6 APPLICABLE PUBLICATIONS
A. The publications listed below form a part of this specification to the
extent referenced. Publications are referenced in the text by basic
designations only.
B. American Society for Testing and Materials (ASTM):
A36/A36M-08.............Standard Specifications for Carbon Structural
Steel
A82-07..................Standard Specifications for Steel Wire, Plain,
for Concrete Reinforcement
A499-89(R2008)..........Standard Specifications for Steel Bars and
Shapes, Carbon Rolled from "T" Rails
A568/A568M-09...........Standard specification for Steel, Sheet, Carbon,
Structural and High-Strength, Low-Alloy, Hot-
Rolled and Cold-Rolled General Requirements for
A653/A653M-10...........Standard Specification for Steel Sheet, Zinc-
Coated (Galvanized) or Zinc-Iron Alloy-coated
(Galvannealed) by the Hot-Dip Process
C317/C317M-00(R2010)....Standard specification for Gypsum Concrete
C1396/C1396M-09.........Standard Specification for Gypsum Board
E119-10.................Standard Test Methods for Fire Tests of Building
Construction and Materials
C. American Welding Society Publication (AWS):
D1.1/D1.1M-10...........Structural Welding Code - Steel
PART 2 - PRODUCTS
2.1 MATERIALS
A. Sub-purlins:
1. Open web truss-tees, hot-rolled bulb-tees or folded sheet metal tees
as required by design loads, spans and fire ratings.
2. Flanges: Provide 16 mm (5/8-inch) minimum bearing for gypsum planks.
3. Galvanize or factory coat sub-purlins with manufacturer's standard
primer.
4. Open web truss-tees: Fabricate from cold-formed steel wire conforming
to ASTM A82.
03 55 11 - 2
07-11
5. Hot-rolled bulb-tees: Rail-shaped, fabricated from hot-rolled steel

conforming to ASTM A36 or ASTM A499.
6. Folded sheet metal tees: Fabricate from sheet steel conforming to
ASTM A653 and ASTM A568.
B. Cross-Tees:
1. Cold-Formed, Fabrication from sheet steel conforming to ASTM A525 or
ASTM A568.
2. Size: 30 mm (1-1/4-inches) by 13 mm (1/2-inch) by 0.6 mm (0.023-
inch) thick by 600 mm (24-inches) long.
C. Gypsum Deck Plank:
1. Fabricated of gypsum board: ASTM C1396.
2. Nominal Size: 50 mm (2-inches) thick by 600 mm (24-inches) wide by
main purlin span. Where possible, length should span two main purlin
spans.
3. Factory laminate from two 25 mm (1-inch) thick gypsum panels with top
panel edge set back along sub-purlin edge not more than 13 mm (1/2-
inch).
4. Edge encased in water-resistant paper.
D. Gypsum Deck Panels: ASTM C1396, Type "X", 16 mm (5/8-inch) thick by 600
mm (24-inches) wide by main purlin span.
E. Grout: Gypsum Concrete: ASTM C317, Class A, 3.5 MPa (500 psi) minimum
compressive strength.
2.2 DECK SYSTEM
A. Interstitial deck: Provide two-hour fire rating as tested by Gypsum
plank manufacturer under ASTM E119 fire test conditions modified to
simulate the Department of Veterans Affairs Building System test
described in National Institute of Standards and Technology Report NBSIR
85-3158, "Fire Performance of Interstitial Space Construction System".
PART 3 - EXECUTION
3.1 INSPECTION
A. Examine substrates, framing and conditions under which gypsum plank is
to be installed and notify Resident Engineer in writing of conditions
detrimental to proper and timely completion.
B. Do not proceed until unsatisfactory conditions have been corrected.
3.2 INSTALLATION
A. Weld per AWS D1.1.
B. Sub-purlins:
03 55 11 - 3
07-11
1. Space at approximately 650 mm (24-5/8-inches) on center to provide

minimum 16 mm (5/8-inch) continuous bearing for gypsum plank or deck.
2. Install framing of openings.
3. Touch up welds with same type of rust-inhibitive paint used for
primer.
SPEC WRITER NOTE:
1. When sub-purlins are used to carry
superimposed loads, such as ceilings,
lighting fixtures or other building
components, consult load tables for
sub-purlin size selection.
2. Select and detail appropriate
attachment methods.
//4. Interstitial Decks: Use 19 mm (3/4-inch) fillet welds on both sides

of sub-purlins at math purlin. //
C. For Two Hour fire rated interstitial decks //.
1. Place gypsum deck panels on bottom flanges of sub-purlins with 16 mm
(5/8-inch) minimum continuous bearing.
2. Place gypsum deck plank over gypsum deck panels, with off-set edges
"up" to form a "T" receptacle for gypsum grout.
3. Cut to fit around openings shown.
4. Install plank to conform to fire test assembly.
D. Provide continuous 16 mm (5/8-inch) minimum bearing for plank support at
deck perimeter, plank ends and openings exceeding 200 mm (8-inches).
E. Grout:
1. Mix gypsum concrete thoroughly using a minimum amount of water to
form a thick, pourable consistency.
2. Fill edge joints to slight excess with single pour at sub-purlins.
a. Grout end joints on single span system against steel framing.
b. After initial set, strike of excess to form smooth, flush joint.
//c. Form cant strips and curbs where shown. //
//3. Fill joints at roof ridges, hips and valleys. //
F. Patching:
1. Fill with grout and smooth any surface damage to gypsum plank.
2. Remove and replace cracked, broken, and plank damaged beyond repair.
G. Cleaning and Protection:
1. Upon completion of gypsum plank decking, remove, debris and sweep
surface clean. Leave ready for subsequent work.
03 55 11 - 4
07-11
2. Protect finished deck from weather and subsequent construction

operations.
3. Provide hardboard or plywood temporary protection over decking
subject to repetitive impact or wheeled loads.
- - - E N D - - -
03 55 11 - 5

SECTION 03 55 11 Gypsum Concrete Floor Decks

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

SECTION 03 55 11 Gypsum Concrete Floor Decks

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SECTION 03 55 11 Gypsum Concrete Floor Decks

Uploaded by

Copyright:

Available Formats

07-11

SPEC WRITER NOTE:

5. Hot-rolled bulb-tees: Rail-shaped, fabricated from hot-rolled steel

1. Space at approximately 650 mm (24-5/8-inches) on center to provide

//4. Interstitial Decks: Use 19 mm (3/4-inch) fillet welds on both sides

2. Protect finished deck from weather and subsequent construction

You might also like