Type Series Booklet

1798.51/4-10 Movitec VCF

High-pressure In-line Pumps
50 Hz

Movitec VCF

Fields of Application Designation

Movitec VCF are employed for hot water recirculation. They Movitec V C F 4 -- 5
are installed in boiler feed circuits or other high temperature ap- Type-series
plications where thermal pipe expansions may occur. Movitec V
Material variant
Design Flange variant
Multi-stage, vertical (horizontal installation see page 4) high- Pump size
pressure centrifugal pumps, with suction and discharge Number of stages
nozzles of identical nominal diameters arranged opposite to
each other (in-line design). Material variants: C
Flange variants/connections: F = round flange
Materials
Standard variants:
VCF: Pump casing is made of cast iron and all other hy-
Operating Data
draulic components are made of stainless steel Movitec VCF
AISI 304 Capacities Q up to 75 m3/h, (21 l/s)
Heads H up to 228 m
Operating pressures pd up to 25 bar 1)
Bearings Operating temperatures t --15 _C to +120 _C
All VCF pumps are supplied with tungsten carbide plain bearing 1) The sum of inlet pressure and head at zero flow point must not ex-
at the hydraulic rotor.
ceed the value stated.

Shaft Seal
Single-acting, uncooled mechanical seal in accordance with Conformity Marks
EN 12756. CE

Drive
Electric motor, 50 Hz, air-cooled, 2- and 4-pole, standard KSB
motor with main dimensions to IEC. Other motor makes subject
to prior consultation with KSB.
Movitec VCF with PTC resistors for 3 kW and above.
Variants: single-phase a.c. motor, frequency-controlled drives.
 Movitec VCF

Selection Charts
n ≈ 2900 1/min

VCF 2 VCF 4 VCF 10 VCF 18 VCF 32 VCF 45

VCF 65

2
 Movitec

Materials
Part No. Description Material
Movitec VCF
101 Pump casing JL 1040
108 Stage casing 1.4301
160 Cover 1.4301
171 Diffuser 1.4301
10-6 Pump shroud 1.4301
210 Shaft 1.4305
230 Impeller 1.4301
341 Motor stool JL 1040
412 O-ring EPDM E425
525 Spacer sleeve 1.4301
529 Bearing sleeve Tungsten-carbide
1) Bearing Ceramic
905 Tie bolt 1.4057
920 Nut 1.4301
932 Circlip 1.4571
1) Rigidly connected to stage casing 108 or diffuser 171

Legend of materials
Description Code and material no. Standard to ASTM

Cast iron JL1040 / GJL-250 EN 1561 A48:40B

Nickel chrome steel 1.4301 / X5CrNi18-10 EN 10088 A276:304
Nickel chrome molybdenum steel 1.4571 / X6CrNiMoTi17-12-2 EN 10088 A276:316
Nickel chrome steel 1.4057+QT800 / EN 10088-3 A276:431
X17CrNi16-2--QT800
1.4305 / X8CrNiS 18-9 EN 10088 A276:303

Please note: The indication of the material designations to ASTM / AISI is not binding.

Material Codes
Mechanical seal Description Code letter to Material
EN 12756
Spring-loaded ring U3 Tungsten carbide (CrNiMo-binder)
Seat ring B Resin-impregnated carbon graphite
Elastomer E EPDM (Ethylene Propylene rubber)
Spring G CrNiMo steel
Other metal parts G CrNiMo steel
Code number 18 U3BEGG Tungsten carbide/Carbon/EPDM (HP seal)

Pressure and Temperature Limits

Temperature of Flange variant / Material variant Max. operating Code number
medium pumped t 2) Connection pressure ps 1) Mechanical seal
– 15 _C to + 120 _C VCF = round flange 3) Movitec VCF up to 25 bar 18
1) The sum of inlet pressure and head at zero flow point must not exceed the value stated.
2) Subject to application limits (see List of Media Handled)
3) Drilled to EN 1092-2 PN 25

3
 Movitec VCF

Horizontal installation

The Movitec VCF can be installed horizontally in systems Dimensions Movitec VCF 2, 4, 10, 18, 32, 45, 65
where the installation conditions do not allow vertical installa-
tion. Motor rating C 1) H A B Ident No.
set
Motor flange B14 (0.37 to 4.0 kW) [kW] [mm] [mm] [mm] [mm]
Movitec VCF 2, 4
0.37 -- 1.1 F2 + 47 120 100 100 47 116 958
1.5 -- 2.2 F2 + 47 120 100 100 47 116 986
3.0 -- 4.0 F2 + 39 120 100 100 47 116 959
5.5 -- 7.5 F2 -- 17 170 100 210 47 116 960
Movitec VCF 10, 18
0.55 -- 1.1 F2 + 47 140 130 130 47 116 961

Motor flange B5 (5.5 and 7.5 kW) 1.5 -- 2.2 F2 + 47 140 130 130 47 116 987
3.0 -- 4.0 F2 + 39 140 130 130 47 116 962
5.5 -- 7.5 F2 -- 17 170 130 210 47 116 963
Movitec VCF 32, 45, 65
1.5 -- 2.2 F2 + 47 170 210 180 47 116 972
3.0 -- 4.0 F2 + 39 170 210 180 47 116 973
5.5 -- 7.5 F2 -- 17 170 210 180 47 116 974
1) Height F2 based on stages, see tape series booklet Movitec VCF
pp 22
The set for horizontal installation contains 2 stainless steel
holding brackets and the required bolts.
Foundation bolts must be supplied by the operator.

max. Ø 13 mm for M12

Holding bracket (pump) Holding bracket (motor)

89-11.01 89-11.02

4
 Movitec

Design Features Movitec VCF

Universal high-pressure pump

up to 25 bar
• --15 _C to 120 _C
• also for chemically aggressive
media
Space-saving vertical design

Easy-to service, robust

three-phase motor
• multi-range voltage /
frequency
• type of enclosure IP 55
• insulation class F
• with PTC resistor for
3 kW and above

Leak-free and resistant

to thermal shocks
• thanks to pump shroud
• due to confined O-rings

Reliable, easy-to-
service shaft seal
• standardized
mechanical seal
to EN 12756

Easy-to-fit shaft of high-alloy

Corrosion-resistant:
steel with two flat faces for
• hydraulic parts and pump
strong shaft/impeller
shroud of high-alloy stainless
construction
steel

Low noise, since the flow

noise is dampened by
water-filled shroud
High operating
reliability
ensured by torsion-
proof pump shroud
• no partition lines on
the outside
• only 2 seal elements

Simple installation
Highly wear-resistant and and piping layout
maintenance-free plain bearing of thanks to in-line design
tungsten carbide / ceramic • insusceptible to
lubricated by the medium outside nozzle
• self-cleaning by forced flushing forces and moments

5
 Movitec VCF

Casing Characteristic Curves 2)

Cast iron pump casing with suction and discharge nozzles of The characteristic curves are based on the following principles:
identical nominal diameters arranged opposite to each other F Tolerances to ISO 9906, Class 2 / Annex A.
(in-line design).
F The motors used for the measurements are standard KSB
motors 1).
Shaft Seal
The shaft seal is an uncooled, maintenance-free mechanical F The characteristic curves were obtained with deaerated water
seal to EN 12756. at a temperature of 20 _C and a density of 1.0 kg/dm3 1).
F The characteristic curves are valid for a kinematic viscosity
Drive of 1 mm2/s (1 cst) 1).
Standard for VCF:
F A minimum permissible flow must be maintained to prevent
-- Electric motor, 50 Hz, air-cooled, 2- and 4-pole, standard
the pump from overheating (see graph).
KSB motor with main dimensions to IEC. Other motor makes
subject to prior consultation with KSB,
up to 2.2 kW 220--240 V/380--420 V,
3 kW and above 380--420 V/660--725 V, Movitec VCF Qmin in m3/h
type of enclosure IP 55, 2 0.3
insulation class F, 4 0.6
up to 4 kW design V18, 10 1.2
5.5 kW and above design V1, 18 2.4
all motors with PTC resistor for 3 kW and above. 32 4.0
45 4.6
Approved variants: 65 6.1
-- Explosion-proof motor II 2 G Eexd/Eexe T3/T4,
design V1/V18, make acc. to our choice.
-- Motor for 500 V mains voltage, design V1/V18, make acc. to
The following curve shows the minimum flow, corresponding
our choice.
to a percentage of the optimum flow Qopt, as a function of the
-- Motor make acc. to customer’s choice (upon request).
-- PTC thermistor for motors < 3 kW temperature of the medium pumped (flow rate at best effi-
ciency point).
Direction of rotation:
Clockwise, seen from the drive side (see arrow indicating direc- Minimum flow
tion of rotation on the motor stool).
30
25
Installation
Q min [%]

Vertical installation (horizontal installation see page 4) 20

15
Coating 10
Cast iron pump casing with powder coating. 5
Stainless steel parts without any additional protective coating. 0
40 50 60 70 80 90 100 110 120
Tests Temperature [°C]
Standard:
Pressure test according to EN 809. F Maximum pressure at the discharge nozzle:
Leak test with water. 25 bar – head at zero flow point with round flange (VCF).
Approved variant (upon request): F NPSH
Hydraulic test evidenced by test report. This test is always car- The NPSH values of the individual characteristic curves are
ried out using the original motor. minimum values corresponding to the cavitation limit; they
The NPSH or the suction head are not measured. refer to deaerated water.
Materials testing A safety allowance of at least 0.5 m must be added when se-
Certificate of Compliance with the Order (corresponds to lecting the pump to compensate for measuring inaccuracies
EN 10204) and minor manufacturing deviations. The NPSH curve re-
In the certificate of compliance with the order the manufacturing flects mean values.
or processing works confirms by way of an informal report with-
1) In case of different parameters, the performance data must be cor-
out specifying test results that the delivery complies with the sti-
pulations of the purchase order (certificate to 2.2 and 3.1 avail- rected accordingly.
able upon request). 2) See example on the following page.

6
 Movitec

Example

18
Number
of stages
7,5 kW

Motor
size

Qmin

NPSH required. A safety allowance of 0.5 m

must be added to the NPSH value of the
characteristic curve when selecting the system.

Power input per stage

at a density of ρ = 1 kg/dm3

7
 Movitec VCF

Combination of Hydraulics
Movitec VCF 2, 4, 10

01 108.01 Stage casing

02 108.02 Stage casing with ceramic bearing
03 108.03 Stage casing without vannes
04 108.04 Stage casing bottom
05 108.05 Stage casing Upper
06 108.06 Stage casing Upper without vanes
Impeller location

no. of casings

26 05
25 01
24 05 01
23 01 02
22 01 01
21 05 02 01
20 02 01 01
19 05 01 01 01
18 01 01 01 01
17 05 01 01 01 01
16 05 01 01 01 01 01
15 05 01 01 01 01 01 01
14 05 01 01 01 02 01 01 01
13 05 01 01 01 01 01 01 01 02
12 05 01 01 01 02 02 01 01 02 01
11 05 01 01 01 02 01 01 01 02 01 01
10 05 01 01 02 02 01 01 01 01 01 01 01
9 05 01 02 02 01 01 01 01 01 01 01 01 01
8 05 01 01 01 01 01 01 01 01 01 01 01 01 01
7 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01
6 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
5 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
4 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
3 01 01 01 02 02 02 01 01 01 01 01 01 01 01 01 01 01
2 02 02 02 01 01 01 02 02 02 02 02 02 02 02 02 02 02
1 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04

Movitec VCF 2-- 4 5 6 7 8 9 10 11 13 15 16 18 20 23 25

Movitec VCF 4-- 4 5 6 7 8 9 10 11 13 15 16 18 20 23 25
Movitec VCF 10-- 4 5 6 7 8 9 10 12 14 16 18 20

8
 Movitec

Combination of Hydraulics
Movitec VCF 18

01 108.01 Stage casing

02 108.02 Stage casing with ceramic bearing
04 108.04 Stage casing bottom
05 108.05 Stage casing Upper
06 108.06 Stage casing Upper without vanes
Impeller location

no. of casings
17 05
16 02
15 05 01
14 02 01
13 05 01 01
12 02 01 02
11 05 01 01 01
10 02 01 01 01
9 05 01 01 01 01
8 05 02 01 01 02 01
7 05 02 01 01 02 01 02
6 05 02 01 01 02 01 01 01
5 05 01 01 01 01 01 01 01 01
4 01 01 01 01 01 01 01 01 01
3 01 01 01 01 01 01 01 01 01
2 02 01 02 02 02 02 02 02 02
1 04 04 04 04 04 04 04 04 04

Movitec VCF 18-- 4 5 6 7 8 10 12 14 16

Combination of Hydraulics
Movitec VCF 32, 45

01 171.01 Diffuser
02 171.02 Diffuser with ceramic bearing
03 171.03 Diffuser Upper
04 108.04 Stage casing bottom
Impeller location

Anzahl Leiträder
13 03
12 03 02
11 03 02 01
10 03 02 01 01
9 03 02 01 01 02
8 03 02 01 01 01 01
7 03 02 01 01 02 02 01
6 03 02 01 01 01 01 01 01
5 03 02 01 01 02 02 01 01 02
4 03 01 01 01 01 01 01 01 01 01
3 03 01 01 01 01 01 01 01 01 01 01
2 02 02 02 01 02 02 02 02 02 02 02
1 04 04 04 04 04 04 04 04 04 04 04

Movitec VCF 32-- 2 3 4 5 6 7 8 9 10 11 12

Movitec VCF 45-- 2 3 4 5 6 7 8 9 10

9
 Movitec VCF

Combination of Hydraulics
Movitec VCF 65

01 171.01 Diffuser
02 171.02 Diffuser with ceramic bearing
550 550 Disc Bottom
Impeller location

no. of diffusers
10 01
9 01 02
8 01 02 01
7 01 02 01 02
6 01 02 01 02 01
5 01 02 01 02 01 02
4 01 02 01 02 01 02 01
3 01 02 01 01 01 01 01 01
2 02 02 01 02 01 02 02 02 02
1 550 550 550 550 550 550 550 550 550

Movitec VCF 65-- 1 2 3 4 5 6 7 8 9

Recommended Spare Parts Stock for 2 Years’ Continuous Operation

Number of pumps of identical size
(including stand-by pumps) --> 2 3 4 5 6 and 7 8 and 9 10 and more
Part No. Description Quantity of spare parts %
10-5 Stage casing compl. with bearing Kit 1 set 2 sets 3 sets 30
Stage casing with bearing (108.02) +
bearing sleeve (529) + impeller (230) +
spacer sleeve, short (525.01)
433 1 Mechanical seal 433 1 set 2 sets 3 sets 30
2 O-rings 412.01
1 O-ring 412.05 (only for cartridge seal)
1 O-ring 412.06 (only for cartridge seal)

List of Media Handled

The data refer to the materials’ chemical resistance. Relevant regulations / standards for pump applications have to be complied
with.
The actual operating conditions must always be checked (concentration, temperature, solids content).
The penetration of air into the system must be avoided by all means.
If the operating conditions differ from the data given (e.g. mixed products) or if the media are not included in the table below, please
contact KSB.
Basic data:
-- Room temperature means a temperature between +10 °C and + 30 °C.
-- Temperature ranges:
D The reference temperature is 20 °C.
D In the case of temperatures <0 °C, please contact KSB.
D If the temperature exceeds > 50 °C, check and observe the fluid’s vapour pressure.
D Max. temperature = 120 °C, unless indicated otherwise.
-- Max. concentration = 100 %, unless indicated otherwise.
-- Solids content max. 20 ppm (depending of particle size), with the exception of corrosive media. Media with a higher abrasive
solids content are as a rule not permitted (ppm = 1 mg/kg).

Medium handled Content Temperature

p Mechanical seal variant
max. % max. in °C 18
Water:
boiler feed water, fully desalinated VCF
boiler feed water, partly desalinated VCF
boiler water (pH < 11.5) VCF

10
 Movitec

Movitec VCF with standard non-controlled KSB motor

1~230 V
Pump size Number Seal Motor Rated Round flange
of code rating current Movitec VCF
stages
t
kW Inom in A Ident No. kg
2 poles
Movitec VCF 2 4 18 0.55 4.5 47 110 766 22.2
Movitec VCF 2 5 18 0.55 4.5 47 110 767 22.6
Movitec VCF 2 6 18 0.75 6.9 47 110 768 25.9
Movitec VCF 2 7 18 0.75 6.9 47 110 769 26.4
Movitec VCF 2 8 18 1.1 8.7 47 110 770 28.2
Movitec VCF 2 9 18 1.1 8.7 47 110 771 28.6
Movitec VCF 2 10 18 1.1 8.7 47 110 772 29.1
Movitec VCF 2 11 18 1.1 8.7 47 110 773 29.6
Movitec VCF 2 13 18 1.5 11.0 47 110 774 34.1
Movitec VCF 2 15 18 1.5 11.0 47 110 775 35.0
Movitec VCF 2 16 18 2.2 15.2 47 110 776 38.5
Movitec VCF 2 18 18 2.2 15.2 47 110 777 39.4
Movitec VCF 2 20 18 2.2 15.2 47 110 778 40.4
Movitec VCF 4 4 18 0.75 6.9 47 110 808 26.5
Movitec VCF 4 5 18 0.75 6.9 47 110 809 27.0
Movitec VCF 4 6 18 1.1 8.7 47 110 810 28.7
Movitec VCF 4 7 18 1.1 8.7 47 110 811 29.2
Movitec VCF 4 8 18 1.5 11.0 47 110 812 33.3
Movitec VCF 4 9 18 1.5 11.0 47 110 813 33.7
Movitec VCF 4 10 18 1.5 11.0 47 110 814 34.2
Movitec VCF 4 11 18 2.2 15.2 47 110 815 37.7
Movitec VCF 4 13 18 2.2 15.2 47 110 816 38.6
Movitec VCF 4 15 18 2.2 15.2 47 110 817 39.5
Movitec VCF 10 4 18 1.5 11.0 47 110 849 39.6
Movitec VCF 10 5 18 2.2 15.2 47 110 850 43.3
Movitec VCF 10 6 18 2.2 15.2 47 110 851 44.0

11
 Movitec VCF

Movitec VCF with standard non-controlled/controlled KSB motor 1)

3~230/400 V up to 2.2 kW, from 3 kW 3~400/692 V
Pump size Number Seal code Motor Pump- Rated
of rating Drive 1) current
stages
t
kW Type Inenn in A Ident No. kg
2 poles
Movitec VCF 2 4 18 0.55 ..000K55.. 2.6 / 1.5 47 110 779 22.2
Movitec VCF 2 5 18 0.55 ..000K55.. 2.6 / 1.5 47 110 780 22.6
Movitec VCF 2 6 18 0.75 ..000K75.. 3.7 / 2.1 47 110 781 25.9
Movitec VCF 2 7 18 0.75 ..000K75.. 3.7 / 2.1 47 110 782 26.4
Movitec VCF 2 8 18 1.1 ..001K10.. 5.8 / 3.3 47 110 783 28.2
Movitec VCF 2 9 18 1.1 ..001K10.. 5.8 / 3.3 47 110 784 28.6
Movitec VCF 2 10 18 1.1 ..001K10.. 5.8 / 3.3 47 110 785 29.1
Movitec VCF 2 11 18 1.1 ..001K10.. 5.8 / 3.3 47 110 786 29.6
Movitec VCF 2 13 18 1.5 ..001K50.. 7.6 / 4.4 47 110 787 34.1
Movitec VCF 2 15 18 1.5 ..001K50.. 7.6 / 4.4 47 110 788 35.0
Movitec VCF 2 16 18 2.2 ..002K20.. 10.4 / 6.0 47 110 789 38.5
Movitec VCF 2 18 18 2.2 ..002K20.. 10.4 / 6.0 47 110 790 39.4
Movitec VCF 2 20 18 2.2 ..002K20.. 10.4 / 6.0 47 110 791 40.4
Movitec VCF 2 23 18 3 ..003K00.. 7.0 / 4.1 47 110 794 51.7
Movitec VCF 2 25 18 3 ..003K00.. 7.0 / 4.1 47 110 795 52.7
Movitec VCF 4 4 18 0.75 ..000K75.. 3.7 / 2.1 47 110 818 26.5
Movitec VCF 4 5 18 0.75 ..000K75.. 3.7 / 2.1 47 110 819 27.0
Movitec VCF 4 6 18 1.1 ..001K10.. 5.8 / 3.3 47 110 820 28.7
Movitec VCF 4 7 18 1.1 ..001K10.. 5.8 / 3.3 47 110 821 29.2
Movitec VCF 4 8 18 1.5 ..001K50.. 7.6 / 4.4 47 110 822 33.3
Movitec VCF 4 9 18 1.5 ..001K50.. 7.6 / 4.4 47 110 823 33.7
Movitec VCF 4 10 18 1.5 ..001K50.. 7.6 / 4.4 47 110 824 34.2
Movitec VCF 4 11 18 2.2 ..002K20.. 10.4 / 6.0 47 110 825 37.7
Movitec VCF 4 13 18 2.2 ..002K20.. 10.4 / 6.0 47 110 826 38.6
Movitec VCF 4 15 18 2.2 ..002K20.. 10.4 / 6.0 47 110 827 39.5
Movitec VCF 4 16 18 3 ..003K00.. 7.0 / 4.1 47 110 833 50.0
Movitec VCF 4 18 18 3 ..003K00.. 7.0 / 4.1 47 110 834 50.9
Movitec VCF 4 20 18 3 ..003K00.. 7.0 / 4.1 47 110 835 51.8
Movitec VCF 4 23 18 4 ..004K00.. 9.0 / 5.2 47 110 836 62.2
Movitec VCF 4 25 18 4 ..004K00.. 9.0 / 5.2 47 110 837 63.2
Movitec VCF 10 4 18 1.5 ..001K50.. 7.6 / 4.4 47 110 852 39.6
Movitec VCF 10 5 18 2.2 ..002K20.. 10.4 / 6.0 47 110 853 43.3
Movitec VCF 10 6 18 2.2 ..002K20.. 10.4 / 6.0 47 110 854 44.0
Movitec VCF 10 7 18 3 ..003K00.. 7.0 / 4.1 47 110 864 54.9
Movitec VCF 10 8 18 3 ..003K00.. 7.0 / 4.1 47 110 865 55.6
Movitec VCF 10 9 18 4 ..004K00.. 9.0 / 5.2 47 110 866 65.3
Movitec VCF 10 10 18 4 ..004K00.. 9.0 / 5.2 47 110 867 66.0
Movitec VCF 10 12 18 5.5 ..005K50.. 12.0 / 6.9 47 110 868 73.5
Movitec VCF 10 14 18 5.5 ..005K50.. 12.0 / 6.9 47 110 869 74.9
Movitec VCF 10 16 18 7.5 ..007K50.. 15.5 / 8.9 47 110 870 76.3
Movitec VCF 10 18 18 7.5 ..007K50.. 15.5 / 8.9 47 110 871 81.7
Movitec VCF 10 20 18 7.5 ..007K50.. 15.5 / 8.9 47 110 872 83.1
Movitec VCF 18 4 18 4 ..004K00.. 9.0 / 5.2 47 110 890 30.8
Movitec VCF 18 5 18 5.5 ..005K50.. 11.8 / 6.8 47 110 891 36.7
Movitec VCF 18 6 18 5.5 ..005K50.. 11.8 / 6.8 47 110 892 37.6
Movitec VCF 18 7 18 7.5 ..007K50.. 14.3 / 8.3 47 110 893 38.5
Movitec VCF 18 8 18 7.5 ..007K50.. 14.3 / 8.3 47 110 894 39.4
Movitec VCF 18 10 18 11 ..011K00.. 26.6 / 15.4 47 110 895 43.4
Movitec VCF 18 12 18 15 ..015K00.. 26.6 / 15.4 47 110 896 150.2
Movitec VCF 18 14 18 15 ..015K00.. 31.7 / 18.3 47 110 897 166.0
Movitec VCF 18 16 18 15 ..015K00.. 31.7 / 18.3 47 110 898 167.8
1) Voltage for controlled motor generally 3~400 V. for currents please refer to type series booklet 4070.5-10

12
 Movitec

Movitec VCF with standard non-controlled/controlled KSB motor 1)

3~230/400 V up to 2.2 kW, from 3 kW 3~400/692 V
Pump size Number Seal code Motor Pump- Rated
of rating Drive 1) current
stages
t
kW Type Inenn in A Ident No. kg
2 poles
Movitec VCF 32 2 18 4 ..004K00.. 9.0 / 5.2 48 887 053 87.0
Movitec VCF 32 3 18 5.5 ..005K50.. 12.0 / 6.9 48 887 054 95.0
Movitec VCF 32 4 18 7.5 ..007K50.. 15.5 / 8.9 48 887 055 101.0
Movitec VCF 32 5 18 11 ..011K00.. 30.5 / 17.6 48 887 056 173.0
Movitec VCF 32 6 18 11 ..011K00.. 30.5 / 17.6 48 887 057 175.0
Movitec VCF 32 7 18 15 ..015K00.. 31.7 / 18.3 48 887 058 191.0
Movitec VCF 32 8 18 15 ..015K00.. 31.7 / 18.3 48 887 059 194.0
Movitec VCF 32 9 18 15 ..015K00.. 31.7 / 18.3 48 887 060 196.0
Movitec VCF 32 10 18 18.5 ..018K50.. 40.5 / 23.4 48 887 061 213.0
Movitec VCF 32 11 18 18.5 ..018K50.. 40.5 / 23.4 48 887 062 215.0
Movitec VCF 32 12 18 22 ..022K00.. 44.5 / 25.7 48 887 063 254.0
Movitec VCF 45 2--1 18 5.5 ..005K50.. 12.0 / 6.9 48 887 083 96.0
Movitec VCF 45 2 18 7.5 ..007K50.. 15.5 / 8.9 48 887 084 100.0
Movitec VCF 45 3--1 18 11 ..011K00.. 30.5 / 17.6 48 887 085 172.0
Movitec VCF 45 3 18 11 ..011K00.. 30.5 / 17.6 48 887 086 172.0
Movitec VCF 45 4--1 18 11 ..011K00.. 30.5 / 17.6 48 887 087 174.0
Movitec VCF 45 4 18 15 ..015K00.. 31.7 / 18.3 48 887 088 188.0
Movitec VCF 45 5--1 18 15 ..015K00.. 31.7 / 18.3 48 887 089 190.0
Movitec VCF 45 5 18 18.5 ..018K50.. 40.5 / 23.4 48 887 090 206.0
Movitec VCF 45 6--1 18 18.5 ..018K50.. 40.5 / 23.4 48 887 091 208.0
Movitec VCF 45 6 18 22 ..022K00.. 44.5 / 25.7 48 887 092 244.0
Movitec VCF 45 7--1 18 22 ..022K00.. 44.5 / 25.7 48 887 093 246.0
Movitec VCF 45 7 18 30 ..030K00.. 56.1 / 32.4 48 887 094 319.0
Movitec VCF 45 8--1 18 30 ..030K00.. 56.1 / 32.4 48 887 095 322.0
Movitec VCF 45 8 18 30 ..030K00.. 56.1 / 32.4 48 887 096 322.0
Movitec VCF 45 9--1 18 30 ..030K00.. 56.1 / 32.4 48 887 097 324.0
Movitec VCF 45 9 18 37 ..037K00.. 65.5 / 37.8 48 887 098 338.0
Movitec VCF 45 10--1 18 37 ..037K00.. 65.5 / 37.8 48 887 099 340.0
Movitec VCF 45 10 18 37 ..037K00.. 65.5 / 37.8 48 887 100 340.0
Movitec VCF 65 1 18 3 ..003K00.. 7.0 / 4.1 47 110 199 81.5
Movitec VCF 65 2 18 5.5 ..005K50.. 12.0 / 6.9 47 110 200 100.0
Movitec VCF 65 3 18 7.5 ..007K50.. 15.5 / 8.9 47 110 201 107.4
Movitec VCF 65 4 18 11 ..011K00.. 30.5 / 17.6 47 110 202 177.0
Movitec VCF 65 5 18 15 ..015K00.. 31.7 / 18.3 47 110 203 194.4
Movitec VCF 65 6 18 15 ..015K00.. 31.7 / 18.3 47 110 204 197.8
Movitec VCF 65 7 18 18.5 ..018K50.. 40.5 / 23.4 47 110 205 216.1
Movitec VCF 65 8 18 22 ..022K00.. 44.5 / 25.7 47 110 206 255.5
Movitec VCF 65 9 18 22 ..022K00.. 44.5 / 25.7 47 110 207 258.9
1) Voltage for controlled motor generally 3~400 V. for currents please refer to type series booklet 4070.5-10

13
 Movitec VCF

Movitec VCF with standard non-controlled/controlled KSB motor 1)

3~230/400 V from 3 kW
Pump size Number Seal code Motor Pump- Rated
of rating Drive 1) current
stages
t
kW Type Inenn in A Ident No. kg
2 poles
Movitec VCF 2 23 18 3 ..003K00.. 12.1 / 7.0 47 110 792 51.7
Movitec VCF 2 25 18 3 ..003K00.. 12.1 / 7.0 47 110 793 52.7
Movitec VCF 4 16 18 3 ..003K00.. 12.1 / 7.0 47 110 828 50.0
Movitec VCF 4 18 18 3 ..003K00.. 12.1 / 7.0 47 110 829 50.9
Movitec VCF 4 20 18 3 ..003K00.. 12.1 / 7.0 47 110 830 51.8
Movitec VCF 4 23 18 4 ..004K00.. 15.6 / 9.0 47 110 831 62.2
Movitec VCF 4 25 18 4 ..004K00.. 15.6 / 9.0 47 110 832 63.2
Movitec VCF 10 7 18 3 ..003K00.. 12.1 / 7.0 47 110 855 54.9
Movitec VCF 10 8 18 3 ..003K00.. 12.1 / 7.0 47 110 856 55.6
Movitec VCF 10 9 18 4 ..004K00.. 15.6 / 9.0 47 110 857 65.3
Movitec VCF 10 10 18 4 ..004K00.. 15.6 / 9.0 47 110 858 66.0
Movitec VCF 10 12 18 5.5 ..005K50.. 20.8 / 12.0 47 110 859 73.5
Movitec VCF 10 14 18 5.5 ..005K50.. 20.8 / 12.0 47 110 860 74.9
Movitec VCF 10 16 18 7.5 ..007K50.. 26.8 / 15.5 47 110 861 80.3
Movitec VCF 10 18 18 7.5 ..007K50.. 26.8 / 15.5 47 110 862 81.7
Movitec VCF 10 20 18 7.5 ..007K50.. 26.8 / 15.5 47 110 863 83.1
Movitec VCF 18 4 18 4 ..004K00.. 15.6 / 9.0 47 110 881 66.8
Movitec VCF 18 5 18 5.5 ..005K50.. 20.8 / 12.0 47 110 882 73.7
Movitec VCF 18 6 18 5.5 ..005K50.. 20.8 / 12.0 47 110 883 74.6
Movitec VCF 18 7 18 7.5 ..007K50.. 26.8 / 15.5 47 110 884 79.5
Movitec VCF 18 8 18 7.5 ..007K50.. 26.8 / 15.5 47 110 885 80.4
Movitec VCF 18 10 18 11 ..011K00.. 52.8 / 30.5 47 110 886 148.4
Movitec VCF 18 12 18 11 ..011K00.. 52.8 / 30.5 47 110 887 150.2
Movitec VCF 18 14 18 15 ..015K00.. 54.9 / 31.7 47 110 888 166.0
Movitec VCF 18 16 18 15 ..015K00.. 54.9 / 31.7 47 110 889 167.8
Movitec VCF 32 2 18 4 ..004K00.. 9.0 / 5.2 48 887 042 87.0
Movitec VCF 32 3 18 5.5 ..005K50.. 12.0 / 6.9 48 887 043 95.0
Movitec VCF 32 4 18 7.5 ..007K50.. 15.5 / 8.9 48 887 044 101.0
Movitec VCF 32 5 18 11 ..011K00.. 30.5 / 17.6 48 887 045 173.0
Movitec VCF 32 6 18 11 ..011K00.. 30.5 / 17.6 48 887 046 175.0
Movitec VCF 32 7 18 15 ..015K00.. 31.7 / 18.3 48 887 047 191.0
Movitec VCF 32 8 18 15 ..015K00.. 31.7 / 18.3 48 887 048 194.0
Movitec VCF 32 9 18 15 ..015K00.. 31.7 / 18.3 48 887 049 196.0
Movitec VCF 32 10 18 18.5 ..018K50.. 40.5 / 23.4 48 887 050 213.0
Movitec VCF 32 11 18 18.5 ..018K50.. 40.5 / 23.4 48 887 051 215.0
Movitec VCF 32 12 18 22 ..022K00.. 44.5 / 25.7 48 887 052 254.0
Movitec VCF 45 2--1 18 5.5 ..005K50.. 20.8 / 12.0 48 887 072 96.0
Movitec VCF 45 2 18 7.5 ..007K50.. 26.8 / 15.5 48 887 073 100.0
Movitec VCF 45 3--1 18 11 ..011K00.. 30.5 / 17.6 48 887 074 172.0
Movitec VCF 45 3 18 11 ..011K00.. 30.5 / 17.6 48 887 075 172.0
Movitec VCF 45 4--1 18 11 ..011K00.. 30.5 / 17.6 48 887 076 174.0
Movitec VCF 45 4 18 15 ..015K00.. 31.7 / 18.3 48 887 077 188.0
Movitec VCF 45 5--1 18 15 ..015K00.. 31.7 / 18.3 48 887 078 190.0
Movitec VCF 45 5 18 18.5 ..018K50.. 40.5 / 23.4 48 887 079 206.0
Movitec VCF 45 6--1 18 18.5 ..018K50.. 40.5 / 23.4 48 887 080 208.0
Movitec VCF 45 6 18 22 ..022K00.. 44.5 / 25.7 48 887 081 244.0
Movitec VCF 45 7--1 18 22 ..022K00.. 44.5 / 25.7 48 887 082 246.0
Movitec VCF 65 1 18 3 ..003K00.. 12.1 / 7.0 47 110 190 81.5
Movitec VCF 65 2 18 5.5 ..005K50.. 20.8 / 12.0 47 110 191 100.0
Movitec VCF 65 3 18 7.5 ..007K50.. 26.8 / 15.5 47 110 192 107.4
Movitec VCF 65 4 18 11 ..011K00.. 52.8 / 30.5 47 110 193 177.0
Movitec VCF 65 5 18 15 ..015K00.. 54.9 / 31.7 47 110 194 194.4
Movitec VCF 65 6 18 15 ..015K00.. 54.9 / 31.7 47 110 195 197.8
Movitec VCF 65 7 18 18.5 ..018K50.. 70.1 / 40.5 47 110 196 216.1
Movitec VCF 65 8 18 22 ..022K00.. 77.1 / 44.5 47 110 197 255.5
Movitec VCF 65 9 18 22 ..022K00.. 77.1 / 44.5 47 110 198 258.9

14
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 2 2900 1/min 92 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 5 US.gpm 10 15 20

0 5 IM.gpm 10 15
270

Qmin *)
250
25 3 kW 800

23 3 kW

200 20 2,2 kW

600
18 2,2 kW

16 2,2 kW
Förderhöhe 150 15 1,5 kW
TDH
Hauteur
Prevalenza 13 1,5 kW
Opvoerhoogte 400
Altura
11 1,1 kW
100 10 1,1 kW
9 1,1 kW ft
8 1,1 kW
m
7 0,75 kW
6 0,75 kW 200
50 5 0,55 kW
4 0,55 kW

0 0
0 1 m#/h 2 3 4

0.0 0.2 l/s 0.4 0.6 0.8 1.0 1.2

6
5
NPSHR
15
m ft
10
2
60

Eta %

0
Leistungsbedarf 0.11
Power Input 0.14
0.10
Puiss. abs.
Potenza ass. hp
Opgenomen kW
vermogen 0.1
Potencia nec.
0.06
0 1 m#/h 2 3 4
20050462--A/0*
Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

15
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 4 2900 1/min 92 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 10 US.gpm 20 30 40

0 10 IM.gpm 20 30
270

250 Qmin *)
800
25 4 kW

23 4 kW

200
20 3 kW
600
18 3 kW

16 3 kW
Förderhöhe 150
TDH 15 2,2 kW
Hauteur
Prevalenza
Opvoerhoogte 13 2,2 kW
400
Altura
11 2,2 kW
100 10 1,5 kW
ft
9 1,5 kW

m 8 1,5 kW
7 1,1 kW
6 1,1 kW 200
50 5 0,75 kW
4 0,75 kW

0 0
0 2 m#/h 4 6 8

0.0 0.5 l/s 1.0 1.5 2.0 2.5

7
m 20
NPSHR 5 ft
10
2
80

Eta %

0
Leistungsbedarf 0.16
Power Input 0.2
Puiss. abs. kW hp
Potenza ass.
Opgenomen 0.15
vermogen 0.1
Potencia nec.
0.08
0 2 m#/h 4 6 8
20050463--A/0*
Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

16
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 10 2900 1/min 100 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 10 US.gpm 20 30 40 50

0 10 IM.gpm 20 30 40
250
Qmin *) 800
20 7,5 kW

18 7,5 kW

200

16 7,5 kW
600

14 5,5 kW

150 ft
Förderhöhe 12 5,5 kW
TDH
Hauteur
Prevalenza m
Opvoerhoogte 400
10 4 kW
Altura
9 4 kW
100
8 3 kW

7 3 kW

6 2,2 kW

5 2,2 kW 200
50 4 1,5 kW

10
0 2 m#/h 4 6 8 10 12

0 1 l/s 2 3
6
5 15
NPSHR
m ft
5
1
80

Eta %

0
Leistungsbedarf 0.4
Power Input 0.5
Puiss. abs.
Potenza ass.
kW hp
Opgenomen
vermogen 0.3
0.2
Potencia nec.
0 2 m#/h 4 6 8 10 12
20050464--A/0*
Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

17
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 18 2900 1/min 110 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 20 US.gpm 40 60 80 100

0 20 IM.gpm 40 60 80
800
240
Qmin *)
16 15 kW
220

14 15 kW
200

600
180
12 11 kW

160
ft
Förderhöhe 10 11 kW
TDH 140
Hauteur
Prevalenza
Opvoerhoogte 400
Altura
120 8 7,5 kW

7 7,5 kW
100

6 5,5 kW
80
5 5,5 kW

60 4 4 kW 200
m
40

20
0 5 m#/h 10 15 20 25

0 2 l/s 4 6
5 15
NPSHR m ft

0 0
80

Eta %

0
Leistungsbedarf 1.0
Power Input 1.2
Puiss. abs.
Potenza ass. kW 1
Opgenomen hp
vermogen
0.5
Potencia nec. 0.6
0 5 m#/h 10 15 20 25
20050465--A/0*
Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

18
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 32 2900 1/min 132 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 50 US.gpm 100 150

0 50 IM.gpm 100 150

250
Qmin *) 800
12 22 kW

11 18,5 kW

200
10 18,5 kW

600
9 15 kW

8 15 kW
150
Förderhöhe
TDH 7 15 kW
Hauteur
Prevalenza
Opvoerhoogte
400
6 11 kW
Altura

100 5 11 kW
ft

m 4 7,5 kW

200
3 5,5 kW
50
2 4,0 kW

0 0
0 5 m#/h 10 15 20 25 30 35 40

0 2 l/s 4 6 8 10
6
5
NPSHR
15
m ft
10
2
80

Eta %

0
Leistungsbedarf 2
Power Input 2.5
Puiss. abs. 2
Potenza ass. kW
Opgenomen hp
vermogen
1
Potencia nec.
0.5
0 5 m#/h 10 15 20 25 30 35 40
K20070244.1
Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

19
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 45 2900 1/min 145 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 50 US.gpm 100 150 200 250

0 50 IM.gpm 100 150 200

270

250
Qmin *)
800
10 37 kW
10-1 37 kW

9 37 kW
9-1 30 kW
200
8 30 kW
8-1 30 kW 600

7 30 kW
7-1 22 kW
Förderhöhe 150
TDH 6 22 kW
Hauteur 6-1 18,5 kW
Prevalenza
Opvoerhoogte 400
Altura 5 18,5 kW
5-1 15 kW

100
4 15 kW ft
4-1 11 kW

m
3 11 kW
3-1 11 kW
200
50 2 7,5 kW
2-1 5,5 kW

0 0
0 10 m#/h 20 30 40 50 60

0 5 l/s 10 15
6
5 15
NPSHR
m ft
5
1
80

Eta %

0
Leistungsbedarf 4
Power Input
Puiss. abs. 4
Potenza ass. kW
Opgenomen hp
vermogen --1
Potencia nec.
0 0
0 10 m#/h 20 30 40 50 60

Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

20
 Baureihe--Größe Tipo Nenndrehzahl Velocità di rotazione nom. Laufrad--ø ø girante
Type--Size Serie Nom. speed Nominaal toerental Impeller dia. Waaier ø
Modèle Tipo Vitesse nom. Revoluciones nom. Diamètre de roue ø rodete

Movitec VCF 65 2900 1/min 126/131 mm

Projekt Progetto Angebots--Nr. N° offerta Pos.--Nr. N° pos
Project Projekt Quotation No. Offertenr. Item No. Pos. nr.
KSB Aktiengesellschaft
Projet Proyecto N° de l’offre N° oferta N° de pos. N° de art 67225 Frankenthal
Johann--Klein--Straße 9
67227 Frankenthal

0 100 US.gpm 200 300

0 100 IM.gpm 200 300

170

160
Qmin *)
500
9 22 kW

140
8 22 kW

120 400
7 18,5 kW

100 6 15 kW
Förderhöhe
TDH 300
Hauteur
Prevalenza 5 15 kW
80
Opvoerhoogte
Altura
4 11 kW

60 200

3 7,5 kW
ft
40
2 5,5 kW
m 100

20 1 3 kW

0 0
0 10 m#/h 20 30 40 50 60 70 80

0 5 l/s 10 15 20
8
20
NPSHR m
ft
0 0
80

Eta %

0
Leistungsbedarf 2.8
Power Input
Puiss. abs.
3.5
Potenza ass. kW hp
Opgenomen
vermogen 3.0
Potencia nec.
2
0 10 m#/h 20 30 40 50 60 70 80
20050466--A/0*
Fördermenge/Flow/Débit/Portata/Capaciteit/Caudal

*) Qmin up to 40 _C, temperatures >40 _C see table page 6

21
 Movitec VCF

Dimension Tables
Movitec VCF 2 2900 1/min

VCF 2 Round flange

No. of
stages PD E1 E2 E3 F1 F2
1 A 134 107 251 476 257
PumpDrive 2 A 134 107 251 476 257
3 A 134 107 251 497 278
4 A 134 107 251 542 299
5 A 134 107 251 563 320
6 A 150 115 251 585 351
7 A 150 115 251 606 372
8 A 150 115 251 657 393
9 A 150 115 251 678 414
10 A 150 115 251 699 435
11 A 150 115 251 720 456
13 A 176 136 286 783 508
15 A 176 136 286 825 550
16 A 176 136 286 846 571
18 A 176 136 286 888 613
20 A 176 136 286 930 655
23 B 194 147 286 1044 728
25 B 194 147 286 1086 770

PumpDrive Dimensions
Variant A B C
A 260 190 158
B 325 250 170
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)

Flange Variants
Round flange PN 25
Movitec VCF

Terminal Box Position for all pump sizes see page 28

22
 Movitec VCF

Dimension Tables
Movitec VCF 4 2900 1/min
VCF 4 Round flange

No. of
stages PD E1 E2 E3 F1 F2
1 A 134 107 251 476 257
PumpDrive 2 A 134 107 251 476 257
3 A 134 107 251 521 278
4 A 150 115 251 543 309
5 A 150 115 251 564 330
6 A 150 115 251 615 351
7 A 150 115 251 636 372
8 A 176 136 286 678 403
9 A 176 136 286 699 424
10 A 176 136 286 720 445
11 A 176 136 286 741 466
13 A 176 136 286 783 508
15 A 176 136 286 825 550
16 B 194 147 286 897 581
18 B 194 147 286 939 623
20 B 194 147 286 981 665
23 B 233 162 305 1052 728
25 B 233 162 305 1094 770

PumpDrive Dimensions
Variant A B C
A 260 190 158
B 325 250 170
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)

Flange Variants
Round flange PN 25
Movitec VCF

Terminal Box Position for all pump sizes see page 28

23
 Movitec VCF

Dimension Tables
Movitec VCF 10 2900 1/min

VCF 10

No. of
stages PD E1 E2 E3 F1 F2
1 A 150 115 251 556 322
PumpDrive 2 A 150 115 251 556 322
3 A 150 115 251 613 349
4 A 176 136 286 661 386
5 A 176 136 286 688 413
6 A 176 136 286 715 440
7 B 194 147 286 793 477
8 B 194 147 286 820 504
9 B 233 162 305 855 531
10 B 233 162 305 882 558
12 B 233 162 328 961 632
14 B 233 162 328 1015 686
16 B 233 162 328 1097 740
18 B 233 162 328 1151 794
20 B 233 162 328 1205 848

PumpDrive Dimensions
Variant A B C
A 260 190 158
B 325 250 170
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)

Flange Variants
Round flange PN 25
Movitec VCF

Terminal Box Position for all pump sizes see page 28

24
 Movitec VCF

Dimension Tables
Movitec VCF 18 2900 1/min
VCF 18

No. of
stages PD E1 E2 E3 F1 F2
1 A 150 115 251 611 347
PumpDrive
2 A 176 136 286 632 357
3 B 194 147 286 717 401
4 B 233 162 305 760 436
5 B 233 162 328 819 490
6 B 233 162 328 854 525
7 B 233 162 328 916 559
8 B 233 162 328 951 594
10 C 315 206 431 1195 693
12 C 315 206 431 1264 762
14 C 315 206 431 1333 831
16 C 315 206 431 1402 900

PumpDrive Dimensions
Variant A B C
A 260 190 158
B 325 250 170
C 420 320 235
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)

Flange Variants
Round flange PN 25
Movitec VCF

Terminal Box Position for all pump sizes see page 28

25
 Movitec VCF

Dimension Tables
Movitec VCF 32 2900 1/min
VCF 32
E3
No. of
stages PD E1 E2 E3 F1 F2
2 B 233 162 305 830 506
PumpDrive 3 B 233 162 328 904 575
4 B 233 162 328 980 623
5 C 315 206 431 1279 777
6 C 315 206 431 1327 825
7 C 315 206 431 1376 874
8 C 315 206 431 1424 922
9 C 315 206 431 1473 971
10 C 315 206 431 1565 1019
11 C 315 206 431 1614 1068
12 C 350 225 431 1711 1116

PumpDrive Dimensions
Variant A B C
B 325 250 170
C 420 320 235
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)

Flange Variants
Round flange PN 25
Movitec VCF

Terminal Box Position for all pump sizes see page 28

26
 Movitec VCF

Dimension Tables
Movitec VCF 45 2900 1/min
VCF 45
E3
No. of
stages PD E1 E2 E3 F1 F2
2-1 B 233 162 328 855 526
2-1 B 233 162 328 883 526
PumpDrive
3-1 C 315 206 431 1182 680
3-1 C 315 206 431 1182 680
4-1 C 315 206 431 1230 728
4-1 C 315 206 431 1230 728
5-1 C 315 206 431 1279 777
5-1 C 315 206 431 1323 777
6-1 C 315 206 431 1371 825
6-1 C 350 225 431 1420 825
7-1 C 350 225 431 1469 874
7-1 D 398 323 518 1524 874
8-1 D 398 323 518 1572 922
8-1 D 398 323 518 1572 922
9-1 D 398 323 518 1621 971
9-1 D 398 323 518 1621 971
10-1 D 398 323 518 1669 1019
10-1 D 398 323 518 1669 1019

PumpDrive Dimensions
Variant A B C
B 325 250 170
C 420 320 235
D 600 450 290
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)
Flange Variants
Round flange PN 25
Movitec VCF

Terminal Box Position for all pump sizes see page 28

27
 Movitec VCF

Dimension Tables
Movitec VCF 65 2900 1/min
VCF 65 Round flange
PN 16
No. of
No
stages PD E1 E2 E3 F1 F2
1 B 194 147 286 886 570
PumpDrive 2 B 233 162 328 1008 679
3 B 233 162 328 1125 768
4 C 315 206 431 1389 887
5 C 315 206 431 1478 976
6 C 315 206 431 1567 1065
7 C 315 206 431 1700 1154
8 C 350 225 431 1838 1243
9 C 350 225 431 1927 1332

PumpDrive Dimensions
Variant A B C
B 325 250 170
C 420 320 235
Dimensions in mm (Details see Type Series Booklet PumpDrive 4070.5-10)

Terminal Box Position for all Pump Sizes

Terminal box position

(plant view)

Flange Variants
Round flange PN 16 Position 3
(Standard Movitec VCF)

Position 9

Position 6

Position 12

28
Movitec VCF

29
 Movitec VCF

Sectional Drawing
Movitec VCF 2, 4, 10, 18

20040174

30
 Movitec VCF

Part No. Description

10-6 Pump shroud

101 Pump casing
108.01 Stage casing
108.02 Stage casing with ceramic bearing
108.04 Stage casing, bottom
108.05 Stage casing, upper
160 Cover
210 Shaft
230 Impeller
341 Motor stool
411.01 Joint ring
411.02 Joint ring
412.01 O-ring
412.02 O-ring
412.03 O-ring
433 Mechanical seal
509.01 Intermediate ring
525.01 Spacer sleeve, short
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
529 Bearing sleeve
554.01 Washer
554.02 Washer
560 Pin
681 Coupling guard
800 Motor (>5.5 kW 801 Flange motor)
862 Coupling shell
901.01 Hexagon head bolt
901.02 Hexagon head bolt
903.01 Screwed plug
905 Tie bolt
914.01 Hexagon socket head cap screw
914.02 Hexagon socket head cap screw
920.01 Nut
920.02 Nut Lock with non metallic insert
920.03 Nut
930 Safety device nord-Lock
932 Circlip (1/1)

31
 Movitec VCF

Schnittbild
Movitec VCF 32

20070217

32
 Movitec VCF

Part No. Description Detail Patronen-Dichtung

from 7.5 kW
10-6 Pump shroud
101 Pump casing
108.04 Stage casing, bottom
160 Cover
171.01 Diffuser
171.02 Diffuser, with ceramic bearing
171.03 Diffuser, upper
210 Shaft
230 Impeller
341 Motor stool
411.01 Joint ring
411.03 Joint ring
412.01 O-ring
412.02 O-ring
412.03 O-ring
412.05 O-ring
412.06 O-ring
433 Mechanical seal
471 Seal cover
500 Ring, cartridge
509.01 Intermediate ring
509.02 Intermediate ring, upper
525.01 Spacer sleeve, short
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
525.06 Spacer sleeve, seal extention
525.07 Spacer sleeve, cartridge
529 Bearing sleeve
554.01 Washer
560 Pin
681 Coupling guard
800 Motor (> 5,5 kW 801 Flange motor)
862 Coupling shell
901.01 Hexagon head bolt
904 Grub screw
905 Tie bolt
913 Vent plug
914.01 Hexagon socket head cap screw
914.02 Hexagon socket head cap screw
914.03 Hexagon socket head cap screw
920.01 Nut
920.02 Nut, lock with non metallic insert
920.03 Nut
930 Safety device, nord-lock
932 Circlip (1/2)

33
 Movitec VCF

Schnittbild
Movitec VCF 45

20070219

34
 Movitec VCF

Part No. Description Detail cartridge seal

from 7.5 kW
10-6 Pump shroud
101 Pump casing
108.04 Stage casing, bottom
160 Cover
171.01 Diffuser
171.02 Diffuser, with ceramic bearing
171.03 Diffuser, upper
210 Shaft
230.01 Impeller
230.02 Impeller, half head
341 Motor stool
411.01 Joint ring
411.03 Joint ring
412.01 O-ring
412.02 O-ring
412.03 O-ring
412.05 O-ring
412.06 O-ring
433 Mechanical seal
471 Seal cover
500 Ring, cartridge
509.01 Intermediate ring
509.02 Intermediate ring, upper
525.01 Spacer sleeve, short
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
525.06 Spacer sleeve, seal extention
525.07 Spacer sleeve, cartridge
529 Bearing sleeve
554.01 Washer
560 Pin
681 Coupling guard
800 Motor (> 5.5 kW 801 Flange motor)
862 Coupling shell
901.01 Hexagon head bolt
904 Grub screw
905 Tie bolt
913 Vent plug
914.01 Hexagon socket head cap screw
914.02 Hexagon socket head cap screw
914.03 Hexagon socket head cap screw
920.01 Nut
920.02 Nut, lock with non metallic insert
920.03 Nut
930 Safety device, nord-lock
932 Circlip (1/2)

35
 Movitec VCF

Sectional Drawing
Movitec VCF 65

Detail cartridge seal

20040437--A

36
 Movitec VCF

Part No. Description

10-6 Pump shroud

101 Pump casing
160 Cover
171.01 Diffuser
171.02 Diffuser, with ceramic bearing
210 Shaft
230 Impeller
341 Motor stool
411.01 Joint ring
411.02 Joint ring
412.01 O-ring
412.02 O-ring
412.03 O-ring
412.05 O-ring
412.06 O-ring
433 Mechanical seal
471 Seal cover
500 Ring Cartridge
509.01 Intermediate ring
509.02 Intermediate ring, upper
509.03 Intermediate ring, lower
525.01 Spacer sleeve, short
525.02 Spacer sleeve, middle
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
525.06 Spacer sleeve, sealextension
525.07 Spacer sleeve, cartridge
529 Bearing sleeve
550 Disc Bottom
554.01 Washer
560 Pin
681 Coupling guard
800 Motor (> 5.5 kW 801 Flange motor)
862 Coupling shell
901.01 Hexagon head bolt
903.01 Screwed plug
904 Grub screw
905 Tie bolt
914.01 Hexagon socket head cap screw
914.02 Hexagon socket head cap screw
914.03 Hexagon socket head cap screw
920.01 Nut
920.02 Nut Lock with non metallic insert
920.03 Nut
930 Safety device, nord-Lock
932 Circlip (1/2)

37
 Movitec VCF

38
Movitec VCF

39
 Movitec VCF

Subject to technical modifications without prior notice.

1798.51/3-10 / 1.3.2008

KSB Aktiengesellschaft
67225 Frankenthal • Johann-Klein-Str. 9 • 67227 Frankenthal (Germany)
Tel. +49 6233 86-0 • Fax +49 6233 86-3401 • www.ksb.com