Product Manual: Synel MLL Payway LTD
Product Manual: Synel MLL Payway LTD
Product Manual: Synel MLL Payway LTD
SY-777/A
Product Manual
All rights reserved. to Synel MLL Payway Ltd. Reproduction or use, without express permission of edi-
torial or pictorial content, in any manner is prohibited. No patent liability is assumed with respect to the
use of the information contained herein. While every precaution has been taken in the preparation of this
manual, Synel MLL Payway Ltd. assumes no responsibility for errors or omissions. Neither is any liability
assumed for damages resulting from the use of the information contained herein. Pictures in this manual
are for illustration purposes only. SY-777/A is a trademark of Synel MLL Payway Ltd. All trade names ref-
erenced herein are either trademarks or registered trademarks of their respective companies.
2
Table of ContentsHarmony Operation and Installation Manual - DRAFT
Table of Contents
Chapter 1 -Introduction ..................................................................................... 5
Chapter 2 -Technical Specifications .................................................................. 6
2.1.Additional Technical and Interface Specifications.................................... 6
2.1.1Options ..................................................................................................................... 7
2.1.2Physical characteristics ............................................................................................ 7
2.1.3Power Requirements ................................................................................................ 7
2.1.4Communication and configurations ......................................................................... 7
2.1.4.1Communication parameters.............................................................................. 7
2.1.4.2Multiple terminal configuration ....................................................................... 7
2.1.4.3Point to point configuration.............................................................................. 8
2.1.4.4Network connections ........................................................................................ 8
2.1.5Selection of the data entry function.......................................................................... 8
Chapter 3 -Apparatus......................................................................................... 9
3.1.Front panel ................................................................................................. 9
3.2.Bottom connection sockets ........................................................................ 9
3.3.Internal components................................................................................. 10
3.3.1Battery back-up modules........................................................................................ 10
3.3.2Memory .................................................................................................................. 10
3.3.3RS-232/485 internal Card....................................................................................... 11
Chapter 4 -Unpacking ...................................................................................... 12
4.1.Contents ................................................................................................... 12
Chapter 5 -Installation ..................................................................................... 13
5.1.Mounting the terminal on a wall.............................................................. 13
5.2.Communication connections ................................................................... 14
Chapter 6 -Technician Mode (Setup) .............................................................. 15
Chapter 7 -Host Computer Interfacing .......................................................... 19
7.1.Installing communication cables ............................................................. 20
7.2.Connecting your PC to the SY-65 ........................................................... 21
7.3.Connecting the SY-65 to a connection box ............................................. 22
7.3.1If communication problems occur.......................................................................... 22
7.4.Making a multi-drop connection ............................................................. 23
7.4.1Cable from the terminal to the connection box ...................................................... 24
3
Table of ContentsHarmony Operation and Installation Manual - DRAFT
4
SY-777A Introduction
Chapter 1 - Introduction
The Synel SY-777/A terminal is intended for use in an industrial environment, where the solid metal casing
and overall structure make installation simple, safe and durable.
SY-777/A offers the broadest range of effective time & attendance monitoring, shop floor control, job cost-
ing, and access control applications.
The terminal has three mediums of access input: Magnetic, bar code, and proximity readers.
The terminal features online/offline modes of operation and communicates in real-time interface using
TCP/IP protocol, which makes it a comprehensive interactive system. It provides online system manage-
ment of employee reports as well as communication of current employees' data.
Terminal communication programming employs Synel's user-friendly interface provided by SYncomm or
other advanced applications. This wide range of compatible communication applications supported enable
easily customizing the terminal to your unique requirements, while Synel's SAL compiler enables flexible
programming. Firmware can be upgraded remotely to facilitate maintenance.
SY-777/A terminals mechanical design offers easy programming, while the back light and 32 character
display allow quick and easy reading. The solid casing and overall structure make installation in an indus-
trial environment simple and safe.
Numeric keys 10
Control keys - 4
Escape, Return,. (dot) and Clear
Browsing keys 2
Modem Yes
TCP/IP Yes
Printer Yes
I/O 2/2
POE Yes
1.1.1 Options
• Reader Types:
• Bar-code slot reader model (Codes: 128, 2/5, 3/9, UPC-EAN)
• Magnetic (Track I, Track II, Track III)
• Proximity reader (125 KHz)
• Mifare reader (13.56 MHz) - Serial Number only
• Wiegand 26/27/34/36/37/44/48bit (as of version 6.201)
• 14400 bps internal modem
full compatibility to: v.32bis, v.32, v.23, v.22, v.21, Bell 212A and Bell 103
to use a modem JP1 of the modem card must be in set to default state (1-2) see “Jumpers” on page -37
for additional information about setting the jumpers.
• Net connection
• Ethernet (10BASE-T/100BASE-T or AUI)
• POE (Power over Ethernet)
For information for using POE see “Setting the terminal for POE (Power over Ethernet) Use”
on page -38.
Chapter 1 - Apparatus
This terminal series is enclosed in a rugged plastic molded casing and is secured to the wall using four
screws and a removable panel.
2 5
3
4
6
1. A 32 character LCD with a back light display is located in the upper part of the front panel. Two
arrow keys are located to the right of the display panel for line up and line down maneuvering.
2. The Alarm light is located to the left of the display. The alarm light is an LED that lights up when:
Half of the memory has been used up
If the terminal is defined as “On-Line” and has lost communication with the host (no pooling
command has been received from the host for more then the value of parameter 8 in SYS table)
The light blinks when the memory is full or when the terminal has not been programmed.
3. The ON button enables a 15 seconds (modifiable using program) manual operation.
4. Eight function keys are located on the left, below the display, and are marked as follows:
IN- ,OUT- , F1, F2, F3, F4, F5, and F6.
5. Up and Down keys for scrolling the LCD screen.
6. A numerical keyboard of fourteen keys, including Return, Escape, and Clear is located in the lower
center of the front panel.
NA
The socket openings for external connections reside at the bottom of the panel from left to right:
• Power
• Reader 1
• Reader 2
• I2C – NOT AVAILABLE
• Network
• Serial – Serial port connection for printer
• Host – RS-232/RS-485
1.3.2 Memory
As a standard feature, the terminal contains a 512 Kb user memory providing storage for data from more
than 50,000 simple operations. This number depends on the length of the programming tables contained in
Chapter 1 - Unpacking
Note: Do not throw away the box or packing materials.
Check the box and contents for signs of damage that may have occurred during shipment. After checking
the box, carefully unpack and check for the following items:
1.1. Contents
The terminal package contains:
• 1 Terminal
• 1 Power cable (assembled or detachable)
• Connector cables cover
• Communication connector complying to the communication type ordered:
• For TCP/IP - TCP/IP communication cable
• For modem - modem to phone cable
• For 232/485 -
- Splitter box
- 8 pin communication cable
• 3 Phillips flat head screws and anchors (3 for brick/cement walls and 3 for plaster walls) for
mounting the terminal.
• Mounting / drilling template.
• User guide on CD.
Chapter 1 - Installation
1.1. Mounting the terminal on a wall
The following section explains the way in which to mount the terminal to the wall. A Mounting template is
provided to mark the places to drill holes for hanging the unit.
The following figure for mounting the unit shows where the hinges for mounting the unit on the wall.
C D
A - 2 drill holes for hanging the unit.
B - Drill hole for element C.
C - Element for securing the unit in place.
D - Security screw for securing the unit to Element C.
Step 1: Make sure the unit is not plugged into a power source. If you have already connected your ter-
minal to a PC, disconnect it. You can reconnect it after you have completed mounting the unit.
Caution: The terminal contains computer components. It should not be mounted where it will be
exposed to extreme heat or cold, water, steam, violent vibrations, high electromagnetic
radiation including high voltage power lines and electrical equipment.
Step 2: Select a location for the terminal. The following guidelines will help you find the best place for
the terminal:
•The terminal should be placed by an easily accessible power outlet.
•Make sure that there is enough space around the terminal for the communication cabling.
•Do not place the communication cable near a source of electromagnetic radiation or radio inter-
ference such as power lines, large machinery, etc.
•If the communication cable is to be wired through the wall, make sure that it is safe to drill a
hole at the desired location.
•For best usability the terminal should be mounted at employee eye-height. The recommended
height is 140cm (4’7”).
Step 3: Mark the place for drilling the holes (A and B) using the provided Mounting template.
Step 4: Drill holes using a 6 mm. (0.23”) drill bit.
Warning: Live wires in the vicinity may contain 115V or 220V. Make sure not to drill into any live
electric wires. Overlooking this warning may result in harmful contact with an electrical
current.
Step 5: The cables can be wired through the wall and positioned with the bottom of the terminal where
they are connected.
Step 6: Screw the screws into the wall leaving enough space (approx. 4mm./0.16”) for hanging the unit
on them (A in the figure above).
Step 7: Detach Security Element C, screwed to the bottom of the unit, and screw it to the wall in
hole location B.
Step 8: Hang the unit on screws A, so that the unit is resting on the Security Holder (C).
Step 9: Screw Security Screw (D) to the bottom of the unit, securing the unit in place.
Step 10: Connect the communication cables to the terminal.
Use the Enter key to scroll between screens, and the line up/down keys for moving between options
within the selected screen. To return to the previous screen use the C key. To exit technician mode double-
click the Enter key. Technician mode enables setting up:
• Real Time Clock (RTC) Calibration
• Baud rate
• Fingerprint unit Baud rate
• Printer Baud rate
• Station ID settings
• Modem rings
• Network connection
Once the technician mode settings are entered into the system and the user exits the Technician menu, the
settings are automatically saved to the terminals Flash memory. If a “Mem Crash” occurs, the terminal
loads the parameters saved in the Flash memory.
Polling Y/N
For polling the user will be asked to choose between Y and N. Then, the terminal will send data
to the server as per the Polling sec. definition.
Polling Sec
Determines the frequency of data transmission to the SY-Server software. If your terminals are
not in online (query) mode, define the polling time as approximately 10-20 sec. Otherwise,
raise polling time to avoid network collisions. Use the numeric keys to define your required
polling time.
MAC SEND (Y/N)
If you want to confirm sending your terminal’s network MAC address to the host. Then after
exiting technician mode the terminal will send the host a “Hardware configuration network”
message informing it of its MAC address, IP etc.
My MAC Address
Displays your MAC address on your terminal’s prompt. here your terminal’s MAC address will
be displayed.
My IP Address
Press line up/down to view the TCP/IP address of the terminal. Use the numeric keys to enter
the IP Address.
Gateway Address
Press line up/down and key-in the required gateway address.
Remote Address
Press line up/down to view the TCP/IP address of the personal computer on which the SY-
Server runs. Use the numeric keys.
Subnet Mask
The subnet mask is the network address plus the bits reserved for identifying the subnetwork.
Use the numeric keys to determine the terminal’s subnet mask affiliation within your local net.
My Port
TCP/IP enables connecting multiple applications via the same address. The port number
selected here is the application identification number used by the computer when communicat-
ing with the terminal. Synel applications use the default port number = 3734 (a designated
Synel port). However, you may change this according to your specific needs.
Host Port
Synel applications use the default port number=3734. However, you may change this according
to your specific needs. Use the numeric keys to change the port number.
Disconct Sec
Disconnect seconds defines the number of waiting seconds before reverting to offline mode.
Click 03 to enable a fast disconnection.
DHCP (Y/N)
To automatically assign a dynamic IP address to your terminal choose Y.
Note: If no IP address was filled-in under My IP Address, then you must use DHCP, therefore
the only option available will be Y!
Set:
MAC Send (Y/N)
Confirms sending the terminal network MAC address to the host. After exiting technician mode
the terminal sends the host a “Hardware configuration network” message informing it of its
MAC address, IP etc.
My IP Address
Press line up/down to view the TCP/IP address of the terminal. Use the numeric keys to enter
the IP Address.
Gateway Address
Press line up/down and key-in the required gateway address.
Remote Address
Press line up/down to view the TCP/IP address of the personal computer on which the SY-
Server runs. Use the numeric keys.
Subnet Mask
The subnet mask is the network address plus the bits reserved for identifying the subnetwork.
Use the numeric keys to determine the terminal’s subnet mask affiliation within your local net.
My Port
TCP/IP enables connecting multiple applications via the same address. The port number
selected here is the application identification number used by the computer when communicat-
ing with the terminal. Synel applications use the default port number = 3734 (a designated
Synel port). However, you may change this according to your specific needs.
Host Port
Synel applications use the default port number=3734. However, you may change this according
to your specific needs. Use the numeric keys to change the port number.
Disconct Sec
Disconnect seconds defines the number of waiting seconds before reverting to offline mode.
Click 03 to enable a fast disconnection.
DHCP (Y/N)
To automatically assign a dynamic IP address to your terminal choose Y.
Note: If no IP address is defined under My IP Address, you must use DHCP.
Step 11: User Field - specify 4 digits which characterize the terminal. This data can also be sent to the
terminal via a system table. This value is sent to the host when the Status command is used.
Step 12: Terminal mode - Specify whether the terminal works in master or slave mode.
Step 13: Global threshold - Skip - not used for SY-777/A.
Step 14: Exiting Technician mode - After setting the previous parameters you get the following
options:
Save Param - Saves your specified setting.
Exit - Exits Technician mode.
Set - Returns to the beginning of the Technician mode parameters enabling you to change or
reset parameters.
Additional - Displays additional parameters according to the parameters selected before, such
as Network parameters if TCP or UDP, or Network mode of Server or Client.
On exiting Technician mode, all of the settings are saved into the terminals Flash protected memory. In
case of memory crash the terminal reloads the settings from the flash memory (does not revert to the fac-
tory default), which enables quick communication after formatting the memory.
Method 1 Method 2
4 (Gnd) (Gnd) 4
5 (TxD) (TxD) 5
6 (RxD (RxD 6
7 7
8 8
The RJ45 connector on the terminal’s side must be a short (12.35mm) RJ45 connector to enable the termi-
nal connector case that hides the connectors to close.
Chapter 1 - Maintenance
1.1. Terminal Maintenance
1.1.1 Once a month
For badge readers:
1. For magnetic badge readers use a special cleaning badge made of plastic with a polishing paper
(made of Al2O3, with a grain size of approximately 16 microns) attached to the part of the badge
where it contacts the magnetic head. Swipe the badge once or twice. Excessive polishing will result
in wearing out of the magnetic reader head.
2. For barcode badge readers use an air gun to remove dirt/dust or a special optical cleaner (e.i.: one
used for eye glasses).
Caution: Alcohol based cleaning solutions must never be used to clean barcode readers.
Card readers
Bar code readers: Use a blower to clean dust off of the head of the reader.
Magnetic badge readers: Clean the reader with a cleaning solution (such as pure alcohol).
Electric system
• Check the voltage of the UPS battery. If it has less than 7 volts, the batteries need to be changed.
• Visually check the battery for leakage.
• Clean all of the electrical contacts inside the terminal with a contact cleaner.
Backup battery:
Making sure that the backup battery is in good condition, according to the following steps:
1. Collect and clear all the data stored in the terminal.
2. Open the terminal.
3. Remove jumper JP7.
4. Check the voltage of the memory back-up battery and make sure it is between 2.8V and 3.1V.
5. Replace jumper JP7.
Step 3: Remove the JP4 jumper from the 1-2 position to 2-3 position.
Step 4: Reposition JP4 to (1-2).
Step 5: Plug the terminal back into a power source and make sure that MEM CRASH reappears in the
terminal display.
On exiting Technician mode, all of the settings are saved into the terminals Flash protected memory. In
case of memory crash the terminal reloads the settings from the flash memory (does not revert to the fac-
tory default), which enables quick communication after formatting the memory.
Display card
2 Led 1
3 Led 2
4 VCC
5 GND
6 Led 3
7 Clock Clock +, For RS-422
8 DATA Data +, For RS-422
9 VS 9v
10 Clock - For RS-422 signal only
Bar code reader
Pin Signal Value Remarks
1 Data(-) For RS-422
2 Led 1
3 Led 2
4 VCC
5 GND
6 Led 3
7
8 DATA Data +, For RS – 422
9 VS 9v
10
Wiegand
Pin Signal Value Remarks
1 Data (6) - For RS-422
2 Led 1
3 Led 2
4 VCC
5 GND
6 Led 3
7 DATA1 Clock+, for RS-422
8 DATA0 + DATA+, for RS-422
9 VS 9v
10 Data (-) Data (-) for RS-422
Note: Change JP18/19 accordingly.
Appendix C - Jumpers
PSD Programming
No. Jumper Description Value Default/Note
5 JP6 Jtag OPEN - Normal work OPEN
programming CLOSED - Programming
Miscellaneous
No. Jumper Description Value Default/Note
6 JP12 Watch Dog in OPEN WDI Disable CLOSED
CLOSED - Normal WORK
7 JP13 RTC 1-2 Normal work Normal work
2-3 Calibration
8 JP7 Battery OPEN Battery OFF CLOSED
CLOSED Battery ON
9 JP18 Reader 1 type Wiegand - CLOSED JP30 must be in (1-2) & JP31 must
Other readers - OPEN be CLOSED
10 JP19 Reader 2 type Wiegand - CLOSED JP30 must be in (1-2) & JP31 must
Other readers - OPEN be CLOSED
11 JP30/ Reader selection JP30 [1-2]
JP31 JP31 [CLOSED]
12 JP5 Tamper switch [1-2] - Enabled
[2-3] - Disabled
13 JP21 Connect (R2 Input) [1-2] - External FPU
to the printer busy [2-3] - Printer busy
or to the external
FPU
14 JP11 VCC CLOSED - VCC ON
OPEN - VCC OFF
15 JP10 Testing current CLOSED - Normal work
charging OPEN - Test current
16 JP14/ VART selection (1) (1-2)/(1-2)/(2-3)/(2-3) Default = value 1
15/16/ u.CPU--> Host
17 u.URT --> Printer
(2) (2-3)/(2-3)/(1-2)/(1-2)
u.CPU--> Printer
u.URT --> Host
17 JP104 POE CLOSED when the POE option is Default OPEN
used
18 JP105 WIFI CLOSED when the WIFI option is Default OPEN
used
19 JP107 SY-795/Modem (1-2) managing the SY-795 graphic Default OPEN
LCD board.
(2-3) CTSB for modem
20 JP106 Rechargable battery for future use Default OPEN
21 JP108 VIno / VIn for future use (2-3)
22 J100 Buzzer ON - enable buzzer (ON)
OFF - disable buzzer
23 J101 for future use (2-3)
24 J102 for future use (OFF)
25 J103 for future use (OFF)
When using POE on the terminal you will need to make the following changes:
CPU Board REV-D:
JP104 should be shorted / P101 should have 7 PINs.
Network cars type B:
V2 should be compatible with POE.
C6/R7/8/9/10 should be removed
P2 Should be 7 PIN
JP13 should be on (1-2)
Net Card Type F:
R1/R2 should be removed / P11 should be mounted /
P2 should have 7 PINs / JP13 should be on (1-2).
For more details please refer to the BOM & scheme file of these two boards.
When using POE use the additional POE-DC2DC board using the Ag90120-S DC2DC module. The
maximum output power is 9Watt, this means that the over-all power consumption of the POE-terminal
with this module is less than 9Watt. Other modules can be used if you need more power.
Program tables
Weekly Message
Fun Fun
Input Test
Data tables
Valid Emp Non Valid
There is an inter-dependency between the different *.jpr tables built by the SAL program which are the
body of the application.
SYncomm builds the tables as per SAL requirements. On the next page please find a brief outline of the
role of these tables.
The correct and logical order for building a project is to begin from the bottom of the flow chart as follows:
Mandatory
1. Input
2. Test
3. Transaction (Test + Input)
4. General (Transaction to Function Key)
5. Weekly (General to day of week)
Optional
1. Employee, Valid, Non valid - optional
2. Messages
3. Time Zone (to be linked to an employee)
4. Printer notes (i.e.: for meal labels)
5. Day Light Saving Time
6. System
7. Scheduler- for relay/modem activated function keys
8. Project info - general information which is not transmitted to the terminal
Messages
Fixed system messages. These messages can be edited or re-written.
Input
Enables defining up to 4 Input sources that typify a reader/sensor. Input sources are as follows:
Magnetic track 1 (ANSI) Requires swiping of an employee card
Proximity Requires placing the card upto a distance of 6-8 cm from the reader
Touch memory
Codabar
Sensor 1
A sensor can activate either a buzzer or a LED.
Sensor 2
Scroll in list A list to be displayed on the clock prompt from which the user can
choose the relevant data (without card) and scroll using the arrow
key.
Valid
An list of IDs of authorized cards. See screen in the page below:
Please note that the IDs indicated in the Employee (see “Employees” on page -3) table and the valid table
must be identical!
The Valid screen is used for defining and determining access levels for each employee:
Step 1: Fill-in the Valid table header row:
Header Table name
ID
Record size These constitute the header (structure) of the valid table.
The data will be filled-in on the right.
Type
Key length
Step 2: On the right fill-in all authorized employee numbers.
Step 3: On the bottom the user can allocate permitted terminals to each employee.
Note: The Valid table ID SHOULD NOT be identical to the Employee table ID.
Not Valid
Parameters identical to those of the valid table but used for denying access to specified employee cards.
Employees
Here you can assign an employee list/employee to a terminal. More than one authorized employee table
can be imported from an external database
Unlike the “Valid” table, this table includes various employee details as you can learn from the table
below:
1 3
2 4
6
5
1 Employee table header (name). It is possible to import various employee tables from an external text
file.
2 The updated terminal list into which updated employee files will be sent.
3 Employee authorized list layout. Here, employees can also be added manually!
4 A list of the terminals to which authorized employees can be assigned and thus allowed access.
nal/s, or the Security Group check box to assign employees according to a security group.
Step 4: If you use the Assign Terminals option, you must now add a terminal to the Permitted termi-
nals for a specified employee. Mark one or more terminal/s on the Terminals list and use
arrow to move it to the permitted terminals list.
Step 5: Employee access through that terminal will be permitted/denied.
Select All Select all terminals from list, a check sign marks the selected terminal.
Clear All Clear all terminals, a circle marks the unselected terminal.
Properties ON/OFF option defines communication software properties.
Printer Notes
This feature is used for printing labels (For example.: meals). First you must go to Set-up | Program Con-
figuration | Printer and define the printer type you are using in your organization. There are several pre-
defined default printer definitions. If none match your specific printer brand, you should define printer
parameters.
Test
This is a mini set-up table for activities and terms to be performed on the transactions. It is possible to per-
form one activity or a sequence of several activities. Some of the relatively simple activities are: saving
transactions, employee access/other validation, displaying specific timed messages. Some of the more
complex activities are: calculation activities (sum, subtract, multiply, compare etc.), variable to variable,
inter-buffer activities.
The Test table is divided into 2 parts:
HEADER
BASE
The header is the test name, it is recommended that the given name will portray the purpose of the test, see
above screen. A new header can be created by either clicking the New button or the key.
The base part is where actual definitions are set, when double clicking a row the following screen appear:
Display message Enables choosing a constant message from the system messages list.
Write last transaction Transmits data that was stored in a designated directory, to be displayed a later stage.
Write transaction Transmits data that was stored to the terminal’s memory. Cannot be displayed.
I - Input data The last value that was received by the terminal.
L - Input length The Number of designated spaces for counting total value length.
P - Input source From which source the last input has arrived, upto four spaces:
1st=type, 2nd+3rd=reader number, 4th=status.
F - File buffer The results of a table search (either employee or valid)= the last record (approx. 30
spaces).
Defines the input length limitation (KB, card number, identification ID etc.) and the offset of
that input number.
File check Enables validating an authorized list with one of the tables on the Locate section. Under File
choose the specific file.
Query A query is sent to the software that is performing an online scan - using SYServer.
Write last Enables saving the last transaction setup in a temporary file for later display as t he employee’s
transaction last transaction.
Store transaction Enables adding transaction data to a buffer.
Write transaction Enables saving all transaction steps (see Transaction folder) in the terminal’s memory. Later
this data can be collected by the host.
Transaction
In this screen the user can define a multi-step transaction, combining Test, Input and prompt message def-
initions. The screen shot below demonstrates the enrolment procedure that requires a supervisor card to be
swiped first.
General
Combines the transaction definitions with a function key on the terminal’s panel.
MM/DD
HH:mm
711/715
HH:mm a/p
DD/MM HH:mm
MM/DD, a/p
HH:mm
Global parameters- Timing of terminal activities.
Sensor parameters- sensor operational parameter.
Error notification- Setting-up error indicators.
Weekly
Combines General definitions of the terminal function keys with a day of the week. Thus, the terminal can
be used differently for each day.
Algorithm 3:
Input: 1 (Even Parity bit) - 10 bits - 20 bits - 1 (Odd Parity bit)
Output - Card number 6 bytes (only 20 bits are decoded)
Algorithm 4:
Input: 1 (Even Parity bit) - 6 bits - 24 bits - 1 (Odd Parity bit)
Output - Card number 8 bytes (only 24 bits are decoded)
33 bit
Algorithm 0
Input: 1 (Even Parity bit) - 7 bits - 24 bits - 1 (Odd Parity bit)
Output - Facility code 2 bytes (7 bits)
Card Number 8 bytes (24 bits)
Algorithm 1
Input: 1 (Even Parity bit) - 10 bits - 21 bits - 1 (Odd Parity bit)
Output - Facility code 4 bytes (10 bits)
Card Number 7 bytes (21 bits)
Algorithm 2
Input: 1 (Do not check parity bit) - 10 bits - 21 bits - 1 (Do not check parity bit)
Output - Facility code 4 bytes (10 bits)
Card Number 7 bytes (21 bits)
36 bit
Algorithm 4
Input: 1 (Even Parity bit) - 6 bits - 12 bits - 16 bits - 1 (Odd Parity bit)
Output - Factory code 2 bytes (6 bits)
Facility code 4 bytes (12 bits)
Card number 5 bytes (16 bits)