Chapter 2. Portland Cement

Chapter 2: Portland Cement
2.1 Definition
A cement is any substance which binds together other materials by a combination of chemical
processes known collectively as setting. Cements are dry powders and should not be confused
with concretes or mortars, but they are an important constituent of both of these materials.
Cement act as the 'glue' that gives strength to structures. Mortar is a mixture of cement and
sand whereas concrete also includes rough aggregates.
Cement is a powdered material with water forms a paste that hardens slowly. It has an
important property that when mixed with water a chemical reaction (hydration) takes place.
2.2 History of Cement
1. The cementitious properties of lime in mortars and concrete have been known since
early historic times. The Romans used lime concretes and developed pozzolanic
cements of lime and certain volcanic earths.
2. Lime mortars and concretes continued to be used in the middle Ages.
3. 1824, Joseph Aspdin from Leeds city - England, produced a powder made from the
calcined mixture of limestone and clay.
4. He called it "Portland Cement", because when it hardened it produced a material similar
to stones from the quarries near Portland Island in UK.
2.3 Raw Materials of Portland Cement
2.3.1 Raw Materials
1. Calcareous rocks such as limestone, marl, chalk.

2. Argillaceous rocks (silica and alumina) such as in clay and shale.
Portland cement production must contain, in proper form and proportions of lime, silica and
alumina.
2.3.2 Chemical Composition of Portland Cements
The raw materials used in the manufacture of Portland cement consist mainly of lime, silica,
alumina and iron oxide .The oxides account for over 90% of the cement. The oxide
composition of (ordinary) Portland cement may be expressed as follows:
The oxide composition of ordinary PC

Approximate
Common Name Oxide Abbreviation
composition limits (%)
Lime CaO C 60-66
Silica SiO2 S 19-25
Alumina Al2O3 A 3-8
İron oxide Fe2O3 F 1-5
Magnesia MgO M 0-5
Alkalies: Na2O N 0.5-1
-soda
K2O K 0.5-1
-potassa
Sulfur trioxide SO3 S 1-3
A Typical Chemical Composition of Ordinary Portland Cement (OPC)

2.4 Manufacturing of Portland Cement
The details of the cement making process vary widely. However, the fundamental stages in
cement production are all the same and as follow.
1- The raw materials are reduced to fine particle size.
2- Raw materials are blended and mixed to produce uniform chemical composition
containing calcium carbonate, silica, alumina, iron oxide etc.
3- The blended raw mix is heated to the point where all the moisture is driven off as steam
or water vapor.
4- The dried mix is heated to 800oC. At this temperature, the calcium carbonate
dissociated into calcium oxide (free lime), and carbon dioxide which driven off as gas.
5- As the temperature rises, principal active compounds of Portland cement form. This
process is completed at a temperature of around 1400oC. Resulting product is Portland
cement clinker (1.8 tons of raw material produces 1 ton of clinker).
6- Clinker is cooled to a temperature of about 60-150oC and stockpiled.
7- Clinker is ground to the specified fineness with the addition of a small proportion of
gypsum to control the setting time of the finished cement.
8- The finished cement is stored in silos for a relatively short time before being sent to the
customer in bags or in bulks.
Production Steps of Portland Cement
1- Crushing, screwing, and stockpiling the raw materials.
2- Calculating the proportions of raw materials.
3- Preparing the raw mix by blending.
4- Feeding the raw mix into rotary kiln.
5- 100oC: Free water is evaporated.
6- 150-300oC: Loosly bound water is evaporated.
7- 500oC: More firmly bound water is evaporated.
8- 600oC: MgCO3 MgO + CO2
9- 900oC: CaCO3 CaO + CO2
10- Reaction between lime and clay starts.
11- 1300oC: Major compound formation starts.
12- 1400-1600oC: Output temperature.
13- (Around 1600oC clinker forms C3A, C2S, C3S, C4AF)
14- Clinker cooled and stored.
15- Clinker is ground with gypsum.
16- Storing and marketing.
2.5 Main Chemical Compounds of Portland Cement
(a) Major Compounds

Portland cements are composed of four basic chemical compounds shown with their names,
chemical formulas, and abbreviations:
Tricalcium silicate = 3CaO·SiO2 = C3S (Alite) (White)
Dicalcium silicate = 2CaO·SiO2 = C2S (Belite) (White)
Tricalcium aluminate = 3CaO. Al2O3 = C3A (White/grey)
Tetracalcium aluminoferrite = 4CaO.Al2O3.Fe2O3 = C4AF (Ferrite) (Dark)
Tricalcium silicate:
Hardens rapidly. Responsible for initial set and early strength.
Dicalcium silicate:
Hardens slowly and its effect on strength increases occurs at ages beyond one week.
Tricalcium aluminate:
Contributes to strength development in the first few days. It is the first compound to hydrate.
The least desirable component because of its high heat generation and its reactiveness with
soils and water which contains moderate to high sulfate concentrations. Cements made with
low C3A contents usually generate less heat, develop higher strengths, and show greater
resistance to sulfate attacts.
Tetracalcium aluminoferrite:
C4AF contributes very little to strength of concrete even though it hydrates very rapidly.
C3S and C2S are the most stable compounds of cement. They are together form from 70 to
80 percent of the constituents in the cement. When cement comes into contact with water, C3S
begins to hydrate rapidly, generating a considerable amount of heat and making a significant
contribution to the development of the early strength particularly in the first 14 days.
In contrast C2S which hydrates slowly and is mainly responsible for the development in
strength after about 7 days. The cement rich in C2S result in a greater resistance to chemical
attack and a smaller drying shrinkage than the other Portland cements.
The hydration of C3A is extremely exothermic and takes place very quickly. It contributes to
high early strength but produces little strength after about 24 hours. C3A is the least stable and
cements containing more than 10 percent of this compound produces concretes, which are
susceptible to sulphate attack.
(b) Minor components

The most important minor components are gypsum, MgO, and alkali sulphates.
Gypsum (2CaSO42H2O) is an important component added to avoid flash set.
Alkalies (MgO, Na2O, K2O) can increase pH value up to 13.5 which is good for reinforcing
steel protection. However, for some aggregates, such a high alkaline environment can cause
alkali aggregate reaction problem.
2.6 Physical Properties of Cement

2.6.1 Fineness:
The reaction between the water and cement starts on the surface of the cement particles. So
the greater the surface area of a given volume of cement the greater the hydration. A fine
cement will develop strength and generate heat more quickly than a coarse cement. It will of
course cost more for grinding the clinker more finely.
Fine cement in general improve the cohesiveness of fresh concrete and can be effective in
reducing the risk of bleeding but they increase the risk of being air-set before use and they
increase the tendency of shrinkage cracking.
The measurement of fineness is defined as specific surface and is expressed as surface area of
the grains in a sample per mass of that sample. In practice, the fineness is usually in the range
350-380 m2/kg.
2.6.2 Hydration:
The chemical combination of cement and water known as hydration produces a very hard and
strong binding medium for the aggregate particles in the concrete. At the end of hydration
normally a heat is liberated which is expressed as calories per gram. The rate of hydration
depends on the relative properties of silicates and aluminate compounds, the fineness of the
cement, and the ambient temperature.
Time taken to achieve 80% hydration and heat of hydration of the main chemical compounds
of Portland cement.
In normal construction where the sizes of the structural members are not so large, the
dissipation of this heat creates no problems. On cold weather concreting, this heat is
advantageous. But in hot weather and in mass concrete construction, this generated heat may
cause thermal cracks, and should be avoided.
The principal hydration product is C3S2H4, calcium silicate hydrate, or C-S-H and is called
glue gel binder. C-S-H is believed to be the material governing concrete strength. Another
product is CH [Ca(OH)2], calcium hydroxide. CH can bring the pH value to over 12 and it is
good for corrosion protection of steel.
The rate of hydration during the first few days is in the order of C3A > C3S > C4AF >C2S.
A typical calorimetric curve of Portland cement is shown in the following figure.

2.6.3 Setting and Hardening:
Setting and hardening of the cement paste are the main physical characteristics associated with
hydration of cement.
The setting times: The time from the addition of the water to the initial and final set are
known as the setting times.
The initial set: The beginning of noticeable stiffening in the cement paste is known as
the initial set.
The final set: The final hardening process which is responsible for its strength known as
the final set.
Setting time is affected by cement composition, cement fineness, rate of hydration, and the
ambient temperature.
2.6.4 Strength:
The strength of hardened cement is its most important property. The rate of hardening of
cement depends on the chemical and physical properties of the cement, the curing conditions
and the water/cement ratio.
2.6.5 Soundness:
Soundness is a physical property of cement paste, which determines the ability of the cement
paste to retain its volume after setting is completed.
The unsoundness is due to the presence of free CaO (lime) and free MgO (magnesia) in
cement. These constituents hydrate very slowly after setting of cement. Since Ca(OH) 2 and
Mg(OH)2 occupy larger volume, expansion takes place.
The unsoundness may be reduced by;
1- limiting MgO content to less than 5%,
2- fine grinding,
3- thorough mixing,
4- Allow cement to aerate for several days (lime may have hydrated or carbonated in
cement).
Tests to measure soundness are (Self Study);
 Le Chatelier test (due to free lime only).
 Autoclave test (sensitive to free CaO and MgO).
2.7 Types of cements
The same type of cement may not be suitable for different locations and climatic conditions.
Therefore, various types of cement have been developed as per the actual requirements. The
necessary changes have been achieved by different methods such as:
1- Changing the oxide composition
2- Changing fineness of cement.
3- Using different additives or mineral mixtures like slag, fly-ash or silica fumes etc.
2.7.1 Types of Cement based on ASTM
ASTM (American Society for Testing and Materials) Types:
Type I: Normal (ordinary) Portland Cement.
Type I-A: Air-entrained type-I Cement.
Type II: Modified Portland Cement.
Type II-A: Air-entrained type-II Cement.
Type III: High Early strength Portland Cement.
Type III-A: Air-entrained type-III Cement.
Type IV: Low heat Portland Cement.
Type V: Sulfate Resistant Portland Cement.
Other Types
White Portland Cement.
High Alumina Cement.
Portland Pozzolan Cement.
Portland Blast Furnace Slag Cement.
Masonry Cement.
Natural Cement.
Expansive Cement.
Type I (Ordinary Portland cement):
It is used for general construction work when the special properties of the other types are not
required and the concrete is not subjected to special sulfate hazard, heat of hydration is not
objectionable, where freezing-thawing is not expected.
Type I-A (Air-Entrained Type-I):
It is used where air entrainment is necessary.
Type II (Modified Portland Cement):
It has better resistance to the action of sulfates than normal (ordinary) Portland cement and
used where sulfate concentrations in groundwater are higher than normal but not very severe.
It also generates heat at a slower rate than OPC and is used in certain concrete mass work like
retaining walls. Reduced temperature rise is beneficial for hot weather concrete, too.
Type II-A (Air-Entrained Type II Cement)
Type III: (High Early Strength Cement)

It is used where high early strengths are required at early periods, usually a week or less. It is
particularly usefull where it is required to remove forms as soon as possible or when the
structure must be brought into service quickly. High-early strength makes it possible to reduce
the period of protection for concrete during cold weather.
Type III-A (Air Entrained Type III)
Type IV (Low Heat Portland Cement):

It is used where the amount and rate of heat generation must be minimized. Strength is also
developed at a slower rate. It is intended for use in massive concrete structures such as dams.
Type V (Sulfate Resistant Portland Cement):
It is used in structures subject to sulfate attack, chemical plants, etc. It is also resistant to the
action of sea water.
2.7.2 Types of Cements based on European Standards (EN 197-1)
European Standards ENV 197-1 classification of common cement types by strength

Chapter 2. Portland Cement

Uploaded by

Copyright:

Available Formats

Chapter 2. Portland Cement

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 2. Portland Cement

Uploaded by

Copyright:

Available Formats

Chapter 2: Portland Cement

2.2 History of Cement

1. Calcareous rocks such as limestone, marl, chalk.

2.3.2 Chemical Composition of Portland Cements

The oxide composition of ordinary PC

A Typical Chemical Composition of Ordinary Portland Cement (OPC)

2.5 Main Chemical Compounds of Portland Cement

(a) Major Compounds

(b) Minor components

2.6 Physical Properties of Cement

A typical calorimetric curve of Portland cement is shown in the following figure.

Type II-A (Air-Entrained Type II Cement)

Type III: (High Early Strength Cement)

Type III-A (Air Entrained Type III)

Type IV (Low Heat Portland Cement):

You might also like