PHYSICS MANUAL (PHY 214L)

DATE: EXPERIMENT NO:

Transistor Biasing Configurations and CE Characteristics.

Objective:

1. To study the transistor biasing configurations.

2. To study the input and output characteristics of a PNP transistor in Common
Base mode and determine transistor parameters.
3. To study the input and output characteristics of an NPN transistor in Common Emitter
mode and determine transistor parameters.

Overview:

A Bipolar Junction Transistor, or BJT is a three terminal device having two p-n-junctions
connected together in series. Each terminal is given a name to identify it and these are
known as the Emitter (E), Base (B) and Collector (C). There are two basic types of bipolar
transistor construction, NPN and PNP, which basically describes the physical arrangement
of the p-type and n-type semiconductor materials from which they are made. Bipolar
Transistors are "CURRENT" Amplifying or current regulating devices that control the
amount of current flowing through them in proportion to the amount of biasing current
applied to their base terminal. The principle of operation of the two transistor types NPN
and PNP, is exactly the same the only difference being in the biasing (base current) and
the polarity of the power supply for each type.
 PHYSICS MANUAL (PHY 214L)
PNP NPN

The symbols for both the NPN and PNP bipolar transistor are shown above along with the
direction of conventional current flow. The direction of the arrow in the symbol shows
current flow between the base and emitter terminal, pointing from the positive p-type
region to the negative n-type region, exactly the same as for the standard diode symbol.
For normal operation, the emitter-base junction is forward-biased and the collector-base
junction is reverse-biased.

Transistor Configurations:

There are three possible configurations possible when a transistor is connected in a circuit:
(a) Common base, (b) Common emitter (c) Common collector. We will be focusing on the
first two configurations in this experiment. The behaviour of a transistor can be
represented by d.c. current-voltage (I-V) curves, called the static characteristic curves of
the device. The three important characteristics of a transistor are: (i) Input characteristics,
(ii) Output characteristics and (iii) Transfer Characteristics. These characteristics give
information about various transistor parameters, e.g. input and out dynamic resistance,
current amplification factors, etc.

Common Base Transistor Characteristics:

In common base configuration, the base is made common to both input and output as
shown in its circuit diagram.

(1) Input Characteristics: The input characteristics is obtained by plotting a curve

between IE and VEB keeping voltage VCB constant. This is very similar to that of a forward-
biased diode and the slope of the plot at a given operating point gives information about
its input dynamic resistance.
 PHYSICS MANUAL (PHY 214L)

Input Dynamic Resistance (ri): This is defined as the ratio of change in base emitter
voltage ( VEB) to the resulting change in emitter current ( IE) at constant collector-emitter
voltage (VCB). This is dynamic as its value varies with the operating current in the
transistor.

∆V EB
r i= ∨ At constant V CB
∆IE

(2) Output Characteristics: The output characteristic curves are plotted between IC
and VCB, keeping IE constant. The output characteristics are controlled by the input
characteristics. Since IC changes with IE, there will be different output characteristics
corresponding to different values of IE. These curves are almost horizontal. This shows that
the output dynamic resistance, defined below, is very high.

Output Dynamic Resistance (ro): This is defined as the ratio of change in collector-base
voltage ( VCB) to the change in collector current ( IC) at a constant base current IE.

∆V CB
r i= ∨ At constant I E
∆IC

(3) Transfer Characteristics: The transfer characteristics are plotted between the input
and output currents (IE versus IC).

Δ IC
Current amplification factor: (α ac = V ¿
Δ I E CB

This is defined as the ratio of the change in collector current to the change in emitter
current at a constant collector-base voltage (VCB) when the transistor is in active state.

Δ IC
α ac = V CB
Δ IE
 PHYSICS MANUAL (PHY 214L)
This is also known as small signal current gain and its value is very large.

The ratio of IC and IE is called α dc of the transistor. Hence,

IC
α dc = V
I E CB

Since IC increases with IE almost linearly, the values of bothα dc andα ac are nearly equal.

Common Emitter Transistor Characteristics:

In a common emitter configuration, emitter is common to both input and output as

shown in its circuit diagram.

(1) Input Characteristics: The variation of the base current IB with the base-emitter
voltage VBE keeping the collector-emitter voltage VCE fixed, gives the input characteristic in
CE mode.

Input Dynamic Resistance (ri): This is defined as the ratio of change in base emitter
voltage ( VBE) to the resulting change in base current ( IB) at constant collector-emitter
voltage (VC E). This is dynamic and it can be seen from the input characteristic, its value
varies with the operating current in the transistor:

∆V BE
r i= ∨At constant V CE
∆IB

The value of ri can be anything from a few hundreds to a few thousand ohms.

(2) Output Characteristics: The variation of the collector current IC with the collector-
emitter voltage VCE is called the output characteristic. The plot of IC versus VCE for different
fixed values of IB gives one output characteristic. Since the collector current changes with
the base current, there will be different output characteristics corresponding to different
values of IB. Output Dynamic Resistance (ro): This is defined as the ratio of change in
collector-emitter voltage ( VCE) to the change in collector current ( IC) at a constant base
current IB.

∆ V CE
rO= ∨ At constant I B
∆ IC
 PHYSICS MANUAL (PHY 214L)

The high magnitude of the output resistance (of the order of 100 kW) is due to the reverse
biased state of this diode.

(3) Transfer Characteristics: The transfer characteristics are plotted between the input
and output currents (IB versus IC). Both IB and IC increase proportionately.

Current amplification factor ( β ac )

This is defined as the ratio of the change in collector current to the change in base current
at a constant collector-emitter voltage (VCE) when the transistor is in active state.

∆ IC
β ac = ∨V CE
∆ IB

This is also known as small signal current gain and its value is very large. The ratio of IC and
IB we get what is called β dcof the transistor. Hence,

IC
β dc = ∨V CE
IB

Since IC increases with IB almost linearly, the values of both β dc and β ac are nearly equal.

Circuit components/Equipment’s:
(i) Transistors (2 Nos: 1 PNP (CK 100 or equivalent) and 1 NPN (BC 107 or equivalent)), (ii)
Resistors (4 Nos.) (iii) Multimeters (3 Nos.), (iv) D.C. power supply, (v) Connecting wires and
(vi) Breadboard.
 PHYSICS MANUAL (PHY 214L)

Circuit Diagrams:

PNP transistor in CB configuration

NPN

transistor in CE configuration
 PHYSICS MANUAL (PHY 214L)
Procedure:

1. Note down the type number of both the transistors.

2. Identify different terminals (E, B and C) and the type (PNP/NPN) of the transistors. For
any specific information refer the datasheet of the transistors.
(I) PNP Common Base (CB) characteristics:
1. Configure CB circuit using the PNP transistor as per the circuit diagram. Use RE = RC =

150Ω.

2. For input characteristics, first fix the voltage VCB by adjusting VCC to the minimum

possible position. Now vary the voltage VEB slowly (say, in steps of 0.05V) by varying

VEE. Measure VEB using a multimeter. If VCB varies during measurement bring it back to

the initial set value to determine IE, measure VRE across the resistor RE and use the

relation IE = VRE/RE.

3. Repeat the above step for another value of VCB say, 2V.

4. Take out the multimeter measuring VEB and connect in series with the output circuit to

measure IC. For output characteristics, first fix IE = 0, i.e. VRE = 0. By adjusting VCC, vary

the collector voltage VCB in steps of say 1V and measure VCB and the corresponding IC

using multimeters. After acquiring sufficient readings, bring back V CB to 0 and reduce it

further to get negative values. Vary VCB in negative direction and measure both VCB and

IC, till you get 0 current.

5. Repeat the above step for at least 5 different values of I E by adjusting VEE. You may

need to adjust VEE continuously during measurement in order to maintain a constant IE.

6. Plot the input and output characteristics by using the readings taken above and
determine the input and output dynamic resistance.

7. To plot transfer characteristics, select a suitable voltage VCB well within the active

region of the output characteristics, which you have tabulated already. Plot a graph
 PHYSICS MANUAL (PHY 214L)
between IC and the corresponding IE at the chosen voltage VCB. Determine α ac from

the slope of this graph.

(II) NPN Common Emitter (CE) characteristics:

1. Now configure CE circuit using the NPN transistor as per the circuit diagram. Use RB =

100kΩ and RC = 1 kΩ.

2. For input characteristics, first fix the voltage VCE by adjusting VCC to the minimum

possible position. Now vary the voltage VBE slowly (say, in steps of 0.05V) by varying

VBB. Measure VBE using a multimeter. If VCE varies during measurement bring it back to

the set value to determine IB, measure VRB across the resistor RB and use the relation
V RB
I B=
RB

3. Repeat the above step for another value of VCE say, 2V.

4. For output characteristics, first fix IB = 0, i.e. VRB = 0. By adjusting VCC, vary the collector

voltage VCE in steps of say 1V and measure VCE and the corresponding IC using

multimeters. If needed vary VCE in negative direction as described for CB configuration

and measure both VCE and IC, till you get 0 current.

5. Repeat the above step for at least 5 different values of IB by adjusting VBB. You may

need to adjust VBB continuously during measurement in order to maintain a constant

IB .

6. Plot the input and output characteristics by using the readings taken above and
determine the input and output dynamic resistance.
 PHYSICS MANUAL (PHY 214L)
7. Plot the transfer characteristics between IC and IB as described for CB configuration for

a suitable voltage of VCE on the output characteristics. Determine β ac from the slope of

this graph.

Observations:
CB configuration:

Transistor code: ________, Transistor type: ______ (PNP/NPN)

RE = _____, RC = ________.

Table (1): Input Characteristics:

Sl. VCB = ___V VCB = ___V

No. VEB (V) VRE (V) IE (mA) VEB (V) VRE (V) IE (mA)
1
2
..
..
10

Table (2): Output Characteristics:

Sl. IE1 = 0 IE2 = __ IE3 = __ IE4 = __ IE5 = __

No. VCB IC VCB IC VCB IC VCB IC VCB IC
(V) (mA) (V) (mA) (V) (mA) (V) (mA) (V) (mA)
1
2
..
..
10
 PHYSICS MANUAL (PHY 214L)

Table (3): Transfer Characteristics: VCB = _______ V

Sl. IE (mA) IC (mA)

No.
1
2
3
4
5

CE configuration:

Transistor code: ________, Transistor type: ______ (PNP/NPN) RB = _____, RC = ________.

Table (5): Input Characteristics:

Sl. VCE = ___V VCE = ___V

No. VBE (V) VRB (V) IB ( A) VBE (V) VRB (V) IB ( A)
1
2
..
..
10
 PHYSICS MANUAL (PHY 214L)

Table (4): Output Characteristics:

Sl. IB1 = 0 IB2 = __ IB3 = __ IB4 = __ IB5 = __

No. VCE IC VCE IC VCE IC VCE IC VCE IC
(V) (mA) (V) (mA) (V) (mA) (V) (mA) (V) (mA)
1
2
..
..
10

Table (6): Transfer Characteristics: VCE = _______ V

Sl. IB ( A) IC (mA)
No.
1
2
3
4
5
 PHYSICS MANUAL (PHY 214L)
Graphs:

Plot the input, output and transfer characteristics for each configuration.

Fig (1). Transistor characteristics in CE Configuration.

 PHYSICS MANUAL (PHY 214L)

CB configuration:

(1) Input characteristics: Plot VEB ~ IE, for different VCB and determine the input
dynamic resistance in each case at suitable operating points.
(2) Output characteristics: Plot VCB ~ IC, for different IE and determine the output
dynamic resistance in each case at suitable operating points in the active region.
(3) Transfer characteristics: Plot IE ~ IC, for a fixed VCB and determine α ac

CE configuration:

(1) Input characteristics: Plot VBE ~ IB, for different VCE and determine the input
dynamic resistance in each case at suitable operating points.
(2) Output characteristics: Plot VCE ~ IC, for different IB and determine the output
dynamic resistance in each case at suitable operating points in the active region.
(3) Transfer characteristics: Plot IB ~ IC, for a fixed VCE and determine β ac.

Precautions:
1. Connect the circuit as per circuit diagram.
2. Make sure that the connections are tight.
3. Take care to apply i) suitable forward voltage across base - emitter junction and ii)
suitable reverse voltage across the collector - emitter junction for . Otherwise the
transistor may be damaged.

Results/Discussions: