BS 4504-Part 1

1 B S I BS*4504: P A R T S 1 67 1 6 2 4 b b î 0277780 T m'
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
BRITISH STANDARD 4504 : 'Part 1 :1969

UDC 621.643.4-034.669.1
SPECIFICATION FOR
FLANGES AND BOLTING FOR
PIPES, VALVES AND FITTINGS
METRIC SERIES
Part 1. Ferrous
O B S 0LESC E N.f
AUG 1989
BRITISH STANDARDS I N S m O N
Copyright British Standards Institution

Provided by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Hong Kong Polytechnic University/9976803100, User=WONG, Kit Chun
No reproduction or networking permitted without license from IHS Not for Resale, 12/26/2018 09:40:02 MST
B S I BS*4504: PARTS3 6 9 Lb24bb9 0277983 I W
BS 4504 : 1969
THIS
BRITISHSTANDARD,
having been approved by the Mechanical Engincering Industry Standards
Committee, was published under the authority of the Executive Board on 23 September, 1969.
SBN: 58005742 9
The Institution desires to call attention to the fact that this British Standard does not purport to incliidc
all the necessary provisions of a contract.
In order to keep abreast of progress in the industries concerned, British Standards are subject to
periodical review. Suggestions for improvements will he recorded and in due course brought to the
notice of the committees charged with the revision of the standards to wliich they rcfcr.
A complete list of British Standards, numbering over 5000, fully indexed and with a note of the contents
of each, will be found in the British Standards Yearbook. The BS Year-book may be consultcd in
many public libraries and similar institutions.
This standard makes rcferencc to the following ßriiisli Standards:
BS 21, Pipe threads.

BS 309. Whiteheart malleable iron castings.
BS 310. Blackheart malleable iron castings.
BS 970. Wrought steels in the form of bars, billets, and forgings, up to 6 in ruling section, foi.
automobile and general engineering purposes. Enseries.
A BS 1400;-- S c h e d u l c - o f - e o p p e r r t I l e ) c i n g o r 4 - a n d - e o y p.
BS 1452, Grey iron castings,
. I
BS 1501. Steels for fired and unfired pressure vesscls. Plates.

BS 1501-6. Steels for use in the chemical, petroleum and allied industrics.
BS 1821. Class I oxy-acetylene welding of steel pipelincs and pipe assemblies for carrying fluids.
BS 2633. Class I arc welding of ferritic steel pipework for carrying fluids. .
BS 2640. Class II oxy-acetylene welding of steel pipelines and pipe nsscniblihs for carrying fluids.
BS 2789. Iron castings with spheroidal or nodular graphite.
Etsw%--.-p-
*sa8?4743~w-effd-eeppw-all-...O-.’
BS 2971. Class I l metal-arc welding of steel pipelines and pipe nsscmblies for carrying fluids:
BS 3643. I S 0 metric screw threads. Part 2, Limits and tolerances for coarse pitch series threads.
BS 3692. IS0 mctric precision hexagon bolts, screws and nuts.
BS 4190. I S 0 metric black hexagon bolts, screws and nuts.
BS 4320. Metal washers for general purposes.
A BS b37.R Ductile iron pipes a d Vtttings.
BS 4622. Grey cast iron pipes and fittings (mctric diinetisions). 1
British Statidrirds are revised, wlieti iiecessary, by the issire eitlier oJotiicticltt~ctitslips or of revised e;l.Ìioris.
It is imporlotif that risers of British Stoti;lurtls slioirltl osrrrtciiti tliot tliiy ore irr possi*ssiori of tiie latest
ntneti(lt,ients or edifiotrs.
’BS4439. Screwed studs for gcneril purposcs. .

.BS4882. Bolting for Ranges and pressurecontaining piirposes.
,
* l i 1 coiirsc of prepuriilion.
Thc following BSI references rrlutc lo ihc work o n I I . .stuiidurd:
~
Conimiiiec refereiicc MEE/i I . MEF./I I;I t h I l for commcnl
67!7402.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*l b9 lb24669 0277982 3 mL
BS 4504 : 1969
CONTENTS
Page P'age
Co-opcrating organizations . . . . . 5 16/1, Integral steel flanges. Nominal pressure
. . . . . .
Forcword , , , . . , . . 6 16bar
1612. Steel welding neck flanges, Nominal pressure
34
SPECIFICATION
16bar . . . . . . .
1613, Steel plate flanges for welding. Nominal
35
I. Scopc . . . . . . . pressure 16 bar . . . . . . 36

2, Design tcmperaturc and prcssurc . i6/4. Steel screwed boss flanges. Nominal pressure
. . . . . . .
3. Dcsignation . . . . . . 16 bar 37
4. Flanges . . 16/5. Steel slip-on boss flanges for welding. Nominal
. . . . . .
. . . . . . . 38
. i , .
pressure 16 bar
5. Bolting
ri Attachmcnt of flanges . .
, ,
16/8. ,Steel plate blank flanges. Nominal pressure
. . .
1. . . .
Hydraiilic tcsting of flangcs.
16bar * .
16/11. Integral grey cast iron flanges. Nominal
39
8. Dctails to Uc supplied by thc piircliascr t4hcn
. . *
ordcring flangcs and/or bolting
pressure 16 bar . . . . . . 40
9. Marking . . . . . . . . . 16/12. Mallcable cast iron integral flanges. Nominal
pressure 10 bar and i 6 bar . . . . 41
16/13. Malleable cast iron screwed boss flanges.
' TABLES
Nominal pressure 10 bar and 16 bar
46/21: Intcgral copper-.-alloy .- flangesr-Nominal
. . 42
AI.
A2,
Prcssurc/tcmpcrature ratings for steel flanges.
Prcssurc/tcmpcratiire ratings for grcy and
IO 0 .pressUrel6 bar-,- r- --
25/1. Intcgral stcel flanges. Nominal pressure 25 bar
.. .- 43-
44
.mallcable cast iron and copper alloy flanges . 13 25/2. Steel welding neck flanges. Nominal pressurc
B. Summary of contents of flange tables , . 14 25 bar . . . . . 45
2.5/2. Stccl wclding ncck flangcs. Nominal pressure 25/3. Steel plate flanges for welding. Nominal
2.5 bar , . . . . 16 pressurc 25 bar , . . , 46
2.513. Siccl plaic flanges for welding. Nominal 25/5. Steel slip-on boss flanges for welding. Nominal
. . . . . .
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
prcssurc 2.5 bar. 17 pressure 25 b a r . 47
2.5/1 I . Intcgral grcy cast iron flangcs. Nominal 25/8.. Steel plate blank flanges. Nominal pressure
prcssurc 2.5 bar. . . . 18 25bar . . , . .
, 48
612. Stccl wclding ncck flanges. Nominal pressure 25/11. Integral grcy cast iron flanges. Nominal
6/3.
6bar , . . .
Stccl plate flangcs for welding. Noiiiinal
19 prcssurc 25 bar
25/12. Mailcablc cast iron integral flanges. Nominal
. . . 49
prcssurc 6 bar , . . 20 prcssurc 25 bar . . so

614. Stccl scrcwcd boss flangcs. Nominal prcssurc 25/13. Mallcablc cast iron screwed boss flanges.
6 bar , . ' 21 Noniinal pressure 25 bar , . 51
B/S. Stccl slip-on boss flanges for wclding. Nominal 25/21;-.lntcgrnl copper -alloy flanges. Nominttt
prcssurc 6 bar . . 22 pr~ssure-25bar-.- .-- .
- - -I-- ,- . -52
616, Stccl loose flangcs for wcldcd on lappcd pipe 40/1, Integral stccl Rangcs. Nominal prcssurc 40 bar 53
cnds, Nominal prcssiirc 6 bar . . 23 40/2. Stccl welding ncck flanges. Nominal pressure
618. Stccl platc blank flanges: Nominal prcssure 40 bar . . . . . 54
6 bar . . 24 40/3. Stccl platc flanges for welding. Nominal
6/l I . Iiitcgral grcy cast iron flanges. Nominal pressure 40 bar . ,. . 55
prcssiirc 6 bar .
, .
6/12. Mallcablc cast iron integral flangcs. Nominal
. . 25 40/4. Stcel screwed boss flanges. Nominal pressure
25 barand40 bar . . , , . 56
prcssurc 6 bar . . 26 40/5. Stcel slip-on boss flanges for welding, Nominal
. .
< I . .
6/13. Mallcnblc cast iron scrcwed boss flangcs. prcssure 40 bar 57

. . .
e . .
Nominal prcssurc6 bar , 27 40/8. Stccl plate blank flangcs. Noniinal pressure
I0/2. Stccl wclding ncck flangcs. Nominal pressure 40bar . . . . . . . 58
IO bar , . .
,
IO/3. Stcci platc flangcs for wclding. Nominal
. 28 .40/2~~ntegral--copper~-silIoy-- flanges.---Nominat
..pressure 4bar-<--. . ,..- . - - - - - .- ..-, -.. . . .59.
. . .
a .
prcssurc IO bar 29 64/1. Integral stcel flanges. Nominal prcssiirc 64 bar 60

1015. Stccl slip-on boss flanges for wclding. Nominal 64/2. Steel welding ncck flangcs. Nominal pressure
pressure IO bar . . . . . . 30 64 bar . . . . . . . 61
I0/6. Stccl loose flangcs for wcldcd on lappcd p i p 64/3. Stcel plate .flanges for welding. Nominal
cnds, Nominal pressurc 10 bar
I0/8. Stccl plate blank flangcs. Nominal prcssurc
. . 31 pressure 64 bar . . . . 62
64/4. Steel screwed boss flanges. Nominal pressure
IO bar
.
, .
1o/ I I Intcgral grcy cast iron flangcs. Nominal
. . . a . 32 6 4 b a r . . . . . . . 63
lOO/l. Intcgral steel flanges. Nominal pressure
prcssurc IO bar , , . 33 100 bar . 64

,.
BSI B S 8 4 5 0 4 : PART*L 6 9 L b 2 4 6 6 9 0277983 5
BS 4504 :1969
pap Page
lOO/2, Steel welding neck flanges. N o r h a 1 pressure 250/1. Integral steel flanges. N&inal pressure
100bar. . . . . . .65 250bar. . . . . . . 7 1
1OO/3, Steel plate flanges for welding. s o m i r i a l 250/2. Steel welding neck flangcs. Nominal pressure
pressure100bar . . . . . 66
l00/4. Steel screwed boss flanges. Nominal pnssure
250 bar . . . . . . . .
320/1. Integral steel flanges. Nominal pressure
72
100bW . . a
160/1. Intcgral steel flanges. Nominal pressurc
67 320 bar . . . . . . . .
320/2. Steel welding neck flange% Nominal pressure
73
160bar . . . . . . . 68 320brri . . . . . . .
&û/i. Integral steel flanges. Nominal pressurc
74
160/2. Steel welding neck flanges. Nominal pressure
160bar . . . . . . . 69 4ûObar. . . . . . . 75
160/3. Steel plate flanges f& welding. Nominal 400/2. Steel welding neck flanges, Nominal pressure
pressure160bar . . . . . 70 4ûObar . . . . . . . . 76
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

a
BSI B S * 4 5 0 4 : P A R T * l 69 = Lb24669 0277984 7
BS 4504 : 1969
CO-OPERATING ORGANIZATIONS
- . .
The Mechanical Engineering Industry Standards Commjttec, under whose supervision this British
Standard was prepared, consists of representatives from the following Government. departments and
scientific and industrial organizations:
*Associated Offices' Technical Committee *Institution of Civil Engineers

*Association of Consulting Engineers *Institution of Gas Engineers
Association of Mining Electrical and Mechanical .. p. Institution of and Ventilating ~~~i~~~~
Engineers
Board of Trade *Institution of Mechanical Engineers
British Chemical Plant Manufacturers' . Institution of Mechanical Engineen
Association (Autamobile Division)
*British Cornprcssed Air Society Institution of Production Engineers
*British Electrical and Allied Manufacturers' - Locomotive and Allied Manufacturers'
Association Association of Great Britain
British Gear Manufacturers' Association
British Internal Combustion Engine
London Transport Board
Machine Tool Trades Associaion
. .
Manufacturers' Association Ministry of Defence
*British Mechanical Engineering Federatioli
British Pump Manufacturers' Association Ministry df Defence, Army Department
*British Steel Industry Ministry of Power
Crown Agents for Oversea Governments and Ministry of Public Building and Works
Administrations Ministry of Technology
Of and Productivity *Ministry of Technology-National Engineering
(H.M. Factory Inspectorate) Laboratory
'Electricity Council, the Central Electricity Ministry of Transport
Generating Board and the Area Boards in
England and Wales National Coal Board
*Engineering Equipment Users' Association National Physical Laboratory (Ministry of
Gas Council Technology)
Institute of Marine Engineers Royal Institute of British Architects
The Government departments and scientific and industrial organizations marked with an asterisk in the
above list, together with the following, were directly represented on the committee entrusted with the
fireparalion of this British Standard:
Black Bolt & Nut Association of Great Britain Ministry of Defence, Navy Department
British Malleable Tubc Fittings Association National Association of Drop Forgers and
British Valve Manufacturers' Association Stampers
British Waterworks Association North East Coast Institution of Engineers and
Copper Development Association Shipbuilders
Institute of British Foundrymen Tank and Industrial Plant Association
Institution of Water Engineers The Welding Institute
Lloyd's Register of Shipping Water-Tube Boilermakers' Association
Metropolitan Water Board Manufacturers of Pipes and Flanges
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*I, 69 Lb24bb9 0277985 9 =
BRITISH STANDARD SPECIFICATION FOR

BS 4504 : 1969
FLANGES AND BOLTING FOR PIPES,
VALVES' AND 'FITTINGS. METRIC SERIES
, ,
. . ...
- - __ . -
--'FOREWORD _.
h SHOULD-BE.NOTED THAT. AT-THE TIME ÖF ISSUING <HI; AMENDMENT, PROPOSALS A R E

UNDER CONSIDERATION WITHIN CEN/WG 74, FLANGES, EFFECTJVELY RECOMMENDING THAT
THE USE OF DIN-BASEDFLANGES IN.BS 4504 BE LIMITEDTO A MAXIMUM PRESSURE m.40 BAR,
IF THESE PROPOSALS ARE AGREED AND RESULT IN THE PUBLICATION OF A EUROPEAN
STANDARD, BS 4504 WILL BE AMENDED ACCORDINGLY. - .
L-
~
This British Standard has baen prepared under the direction of the Mechanid Engineering Industry Standards Committee
and is ohe of those intended for use by industry as it adopts the metric system.
Before 1939 the I.S.A. (International Federation of the National Standardization Associations) prepared bulletins for:
European Standardization and in 1940, Bulletin 5% ' Pipes and connections *, was circulated, and this has been reflected
in the national standards of European countries since that time.
On the formation of the I S 0 (International Organization for Standardization) Technical Committee 5, ' Pipes and
fittings ', set up subcommittees to deal with pipes and flanges and recommendations have been published for 'pipes as
follows: 4
ISO/R 7. Pipe thrads for gas list tubes and screwed fittings where pressure-tightjoints are made on the threads (% in'
to 6 in). (BS 21 is in accord.)
ISO/R 13. Cast iron pipes, spcial castings and cast iron parts for pressure main lines.
ISO/R 64. S e l tubes. Outside diameters. (The appendices to BS 36014 are in accord.) ~
ISO/R 65. Steel tubes suitable for screwing in accordance with I S 0 Recommendation R 7. (BFf387 is in accord.)
ISO/R 134. Non-screwed steel tubes for general purposes (2nd edition).
ISO/R 221. Steel tubes. Thicknesses. (The appendices to BS 36014 are in accord.)
ISOjK 228. Pipe threads where pressure-tight joints are not made on the threads (% in to 6 in).
ISO/R 336. Plain end steel tubes, welded or seamless, General table of dimensions and masses per unit length.
Tho I S 0 TC5 subcommittee concerned with the standardization of flange dimensions was unable to come to any
agreement as the ISA, ASA and BS 10 flange dimensions were not compatible.
Since the publication of the 180 recommendations mentioned above European national standards organizations' have
been revising their flange standards to bring the flange to pipe connecting dimensions into accord with Recommendations
N64,and R/336. The German Standards Association (DNA) has made much progress in this field.
\
The BSI committee reviewed the ISA flange tables and particularly the German DIN standards and has modelled this
British Standard ont them. Acknowledgement is here made for the co-operation extended by the DNA. The mating
dimensions in this standard are therefore in accord with European practice. However, the pressureltemperature ratings
given in Table AI have been adjusted to take advantage of the long term testing and long experience of the BS 10' ratings
AJ alfered fot W b o n S t d flanges.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
'an"ory 19'
It is the practice in Europe to use steel welding neck flanges for all pressure/temperature ranges. Plate flanges are more;
commonly used in the UK and are therefore included in this standard.
Q A i olrrrrd This British Standard incorporates current European practice, It should be noted that there are some European stnnd-
1971 ards for cast iron pipes based on ISO/R 13, 'Cast iron pipes, special castings and cast iron parts for pressure lines ', the
flange dimensions of which differ marginally from those given in Tables lO/ll and 16/11 but these differences do not
'affect mating dimensions. It is intended to develop ductile cast iron flanges to the ISA bulletin mating dimensions and in
add them to this standdrd in due-course.
'NOTE 1. Rcssurci in this standard am liven in bar (gauge) 1 b u = 10 N'hi'.
NOTE 2. All dimensions throuihout this standard am in mill¡melms unless othcrwiw stated.'
. . BS 10, ' Flanges and bolting for pipes, valves and Rttinp *.

B S I BS*Li504: PART*3 bï m 3624bbï 0277986 O m
DS 4504 : 1969
SPECIFICATION
Details for ductile iron pipesand ductile iron pipe fittings are specified in BS 4772.
A t addrd
January 1972
and
Frbruary 1972
A Immediately after this new sentence insert the following new paragraph:
Detailsol flanges for grey iron pipesand grey iron pipe fittings are specified in BS 4622-
The types and materials of gaskets used shall be agreed .
1.1 SCOPE between the purchaser and the manufacturer.

This British Standard specifies requirements for circular . For the purpose of interchangeability in the mating of
flanga of the following types and materials with the flanges, the dimensions which relate to the outside dia-
appropriate batting : meter of the flange, pitch circle diameter of drilled holes,
and the number and size of bolts, shall apply regardless of
Integral: steel, cast iron, malleable cast iron the materials from which the flanges are manufactured,
It should be noted, however. that full face gaskets are
Welding neck: steel. necessary for copper alloy integral flanges up to 100 mm
Plate: steel. nominal diameter.
Screwed boss: steel and malleable cast iron:
NOTE I. The term plate Bange ' indicates the shape or the flange.
Slip-on boss: steel. Such flanges are not necessarily made from steel plaie but may be
Loose for welded on lapped pipe ends: steel. . made from forged or cast steel.
Blank: steel. NOTE 2. The term ' integral flange applies to flangc2in'cgrd wilh
pipes, valves rind things.
6-Q
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

E S 1 BS*4504: PART*L 69 = Lb24669 0277987 2
2. DESIGN TEMPERATURE AND PRESSURE

The temperature end pressure ratings given in Table AI
and A2 arc design pressures and temperatures for the
materials listed. Where there is an appropriate application
standard it is the responsibility of the purchaser to ensura
that the des.@ pressure and temperature stated comply
with the requirements of that standard.
The pressure ratings for materiais other than grey cast
iron am applicable to installations subject to moderate
shock such as may m u r in well designed and efficiently
operated boiler feed mains. Where a system may be subject
to severe shock it is the responsibility of the purchaser to
make a suitable allowance when stating the design
pressure.
The pressure rating for grey cast iron flanges, where
such are used in pipelines containing water, are for non- I
shock conditions. Where moderate shock (such as may

occur in an efficiently designed and operated boiler feed
main) is likely to be present, the pressure and temperature
rating should be reduced by 25 %.
3. DESIGNATION
The flanges shall be designated by the nominal sizC and
flange table reference.
The first part of the table referena is the nominal
pressure<Pl.r),
’ The second part of the table reference indicates the
material and type of flange as follows:
1. Steel-integral.
2. Steel-welding neck.
3. Steel-plate for welding.
4. Steel-screwed boss.
5. Steel-slip-on boss.
6. Steel-loose for welded-on lapped pipe ends.
8. Steel-blank plate.
11. &ey cast iron-integral.

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
12. Malleable cast iron-integral.

13. Malleable cast iron-screwed boss.
4. FLANGES
4.1 Materials. Materials shall be. those given in Ta-iles A
and A2 except that alternativc materials may be used
provided that their mechanical properties are not inferior
at the operating temperature. Where there is an appropriate
application standard it is the responsibility of the purchaser
to ensure that the materials comply with the requirements
of that standard. In this respect attention is drawn to
BS 806 and BS 759,
Certified materials are specified for carbon steel flanges
for use at temperatures in excess of 400°C ynd recorn=
mended for alloy steel flanges for use at temperatures in
excess of 475°C. Representative elevated temperature
tests at the temperature or temperatures specified by the
purchaser shall not be required for material specified to
the order provided the manufacturcr has obtained ccrti-
fication approval for thc supply of matcrial covcîxd by thc
relevant material spccification, following the procedure
described in BS 3920, which lays down conditions undcr
wliich he shall denionstratc thut ihc siccl in questioh
consistently has ihe properties specified in the relevant
maferial specification. . 7

E S 1 BS*4504: P A R T * L 69 = 1624669 0277988 4
I
I
l
. ..-
4.2 Machining of flanges.
4.2.1 All flanges shall be free froni laminations and surface defects.
4.2.2 Flanges shall be finished as follows.
( i ) All flanges shall have their jointing surfaces machine finished, The finish,of jointing surfaces up to and including
PN 40 shall not be coarser than given in the following table appropriate to the method of machining. For flanges
. above PN 40 it is recoinmendcd that ihc surface finish should comply with the rcquirements of BS 1560.
hlclhod of mnrhlnlng 1 R. I R.= 1 Rr

' I
RSll34
, Grade ref. ' A
iim pin Irm
Turning 12.5 500 50 1087.5 N.10
Other than tiirning 3.2. 125 12.5 1022.85 N.8
NOTE. Thc term 'tiirning' ixludes any method oîmuchining producing conccniric or spiral grooves.
(I)Flange outside diameters may be unniachined unless a machine finish is specified by the purchaser.
(3) Unlcss otherwise specified by the purchaser, all bolt holes shall be drilled, shall be equally spaced on the pitch I
circle diameter and, in the caw of integral Ranges. shnll be drilled off-centre.
(4) Bearing surfaces for nuts shall be parallel to the flange jointing face within I O..
4.3 Tolerances on Bange &meter, thickness and length of

.
weldlng necks Flanges shall be subject to the following
tolerances.
4.3.1 Outside diameter (O)

Nqt
Machined machined
Up to 200 inclusive f l &2
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Over 200 to 300 inclusive fl.5 *2
Over 300 to 400 inclusive f2 *3
Over 400 f2 d3
43.2 Thickness (b)
43.2.1 Flanges integral with valves and fittings (other than

forged stee) Q
No!
Thickness Machined mnchined
at back at back
up to IO +1*5 3-2.5
-0 -0
Over 10 up to 20 inclusive +2-o +3-5
-0 -0
Over 20 up to 30 inclusiva 3-23 +4*5
-0 -0
Over 30 up to 50 inclusivo +3*0 +6*5
-0 -0
Over 50 up to 70 inclusive 3-4.0 t a s 5
A i alrered
-0 -0 January i972
Over 70 up to 100 inclusive 3.5.0 3.104

-0 -0
Over 100 +7*0 +14.5
-0 -0
4.3.23 Flanges not integral with valves and fittings and
forged steel
and fittings.
integral with valves A
AI O d d d
Frbruary i972
Not
Thkknesr Machined machined
at back at back
Up to 35 inclusiva +les f 3
I -0 -0
Over 35 +3 3.5
-0 -0
a Ductile iron pipo filtlngs and accessories for pteuure pipelines : A

-
(In course of preparntion.)
For tolerances on grey cast iron pipes with flanges scs BS 4622
' Grey erst iron pipes and fillings (iiietric dinipnsions) I.
-
1 BSI BS*Ll504: PART*:L 69 m L b 2 4 b b 9 0277989 b m
6. ATTACHMENT OF FLANGES
6.1 The method of securing flanges (othcr than inteprii;
BS 4504 : 1969 tlanges) to pipes and fittings shall be in accordance with
the appropriatc applicatlon standard. Where there is no
4.33 Leqyerh of welding neck ßmge (hi) application standard the method of attachment shall tx
Machined the subject of agreement between the purchaser and the
Up to 80 nominal size inclusive fl.5 manufacturer.
Over 80 to 250 nominal
size inclusive f2 6.2 Flanges shall be prepared for attachment to pipes as
Over 250 nominal site f3 follows.
6.2.1 ScrewedJunges. Screwed flanges shall be screwed in

4.4Joint faces accordance with the appropriate table (see Clause 8.
item (5) ì.
Ar alrered
January I972
4.G.l The standard form ofjoint face for flanges covered by
this specification shall be as follows: 6.2.2 Sfeeiplate and steel slip-on 60ss~%7nges.Steel platc
and steel slip-on boss flanges shall be machined in tlie borc
to a diameter to be specified by the purchaser and suirablc
A for welding to form one of the types in the appropriatc
application standard as required by the purchaser. Tlic
purchaser shall speciiy the weid preparation required.
(t 1 cast iron integral
flanges shall have raised joint faces as shown in the tables 6.2.3 Welding neckflanges. Welding neck flanges shall tx
unless specified otherwise by the purchaser. machined in the bore to a diameter to be specified by thc
(2) Malleable cast iron screwed flanges shall have flat purchaser, and suitably prepared for welding to pipes an2
joint faces. fittings. The thickness of the portion.of the flange whicl-
(3)Steel flanges shall have raiscd joint faces except that connects it to the pipe shall be not less than the p i p
blank flanges may be flat faced or have a spigot at the thickness nor more than 3 mm thicker.
option of the manufacturer.
6.2.4 Looseflanges. Loose flanges shall he machined ir
4k.2 Where i t is impractical for tlie manufacturer to accordance with the appropriate table.
provide a raised joint facc on cast iron or steel Ilanges the
flange may be flat faced, its tliickncss being in accordance
with the values specified for dimension 'b' clscwhere in this
standard. --
Q 4.rc.3 I t is thc rcsponsibility of ihc user to sclcct gasket material which is suitable for the fluid at the intended working
tenipcraturc and prcssurc conditions.
5. BOLTING
Material8 and threads. The design temperature and
pressure ratings given in Tables A l and A2 are for the
bolting materials listed. Alternative materials may be used
provided their mechanical properties are not inferi0.r at
. -
the operating temperature.
A 5.1.2 The diiiicnsions and finish of studs arid hexagon hcadcd holts with hexagon niits shall coniply wiíli the require-
ments of OS 3692, BS 4 190 or RS 4439 as iippropriiile.
5.1.3 The diiiiensions and finish of stiid bolts with hexagon nuts shall comply with ihc rcquircments of ES 4882:
1973, Scctioiis I aiid 2.
5.1.4 S t u d bolls may bc of the foriiis shown in BS 4882 exccpt that forni 'b' applies only to stud bolts of othcr than
illloy stccl.
5.1.5 Frcc cutting stcels for studs. bolts. stud bolts and nuts shall only be perniillcd when spccificd by ihc piirchascr,
und their iisc shiill bc rcstrictcd to thc tenipcratiirc range -10 "C to 100 "Cfor noininal prcssiircs tip l o and including
IO ber,
5.1.6 Whcrc washers arc uscd they shall bc of an appropriutc iiiiitcrial and their dimcnsions shall coniply with the
rcqiiirciiicnts ofTul>lc3 of HS 4320:1968.
Siiindard Muck noriiiul scrics wushcrs coniplying with thc rcqiiircnlcnts of nS 4320 may be iiscd for thc tcinpcrutiirc
-
rungc 30 "C to 2M "C.
I
* ' BS 3692, I S 0 rnelric precision hexagon bolts, scre\va niid 111:'
t ES 4190, ' I S 0 mciric black hexagon bolts, screws iitiil 11111s.
BS 3643, ' IS0 mciric x r i c s threads,*. Pari 2, ' I.tniii\
tolerances for coursc pitch scrici threads .
4320, ~ ~ i wiislicrs
d l lor gcncrul cnginccring piiriww-
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

B S I BS*4504: PART*I, b9 l b 2 4 b b 9 0277990 2
BS 4504 : Part i : It/!
- 1
7, HYDRAULIC TESTING OF FLANGES
This standard does not specify the hydraulic test pressures
for flanged pipes or components, details of which should
be obtained from the appropriate standards which
(2) Whether test certificates of .the material are
'
specify test pressures for pipes or components, but the
test pressure applied to the joint shall not exceed 1-5 times
*I required.
(3) Details of bolting (if required) (see C l a w 5).
the nominal pressure for the flanges. (4) Details of the machining for the attachment of
A flanges (see Clause 6).
(5) Whether taper or parallel screwing is required (sce
6.2).
(a) Whether flanges are to be machined (sec 4.2G4.3) A
8. DETAILS TO BE SUPPLIED BY THE PURCHASER 9. MARKING
WHEN ORDERING FLANGES AND/OR BOLTING Flanges made of alloy steel shall be clearly marked so that
The following information shall be supplied by the the material from which the flange is made can be
purchaser when placing an order or making an enquiry: identiRed, except that integral flanges need not be marked
(1) Nominal size, nominal pressure, type of flange where the component itself is marked.
(see flange tables) and material (see Tables A l and A2).
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

E S 1 BS*4504: P A R T * 3 69 3624669 0277993 4 a
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*q504: PART*KL 6 9 W L b 2 4 b b 9 0277992 b
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
.&.-*- --.--..
. t .* LB
II

BSI B S * 4 5 0 4 : PART*KL 69 3 6 2 4 b 6 9 0277993 B =
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
12

B S I BS*4504: P A R T * 1 69 m 1624669 0277994 T m
-. ..... ....
< . t +, M
I'
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*4504: P A R T * L 69 m 1624669 O277995 L m
d
?i
:
w
14
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PARTUL 69 L b 2 4 6 6 9 0277996 3
4 4
BS 4504 :1969
I i
,
-
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
I
1 ,
r
)r.
I5

B S I BS84504: PART*KL 69 L b 2 4 6 6 9 O277997 5 =
BS 4504 : 1969
Ø
TABLE B. SUMMAR / OF CC JTENTS ~
A i rlrrrrd Marrh. 1971
mm li
Q
6
8
10 j,
15
20
25
32
40
50
65
80
100
125 $
150 2
175
'200 3
250
300
3
350
A 400
450
500
600
--700
800.
900
lo00 7
1200 x
1400 X
1600 x
1800 x
2Ooox
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
2200
2400
2600
2800
3Ooo
3200
3400
3600
3800
4ooo

BSI B S * 4 5 0 4 : P A R T r 1 69 1624669 0277998 7
ES 4504 : 1969
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BS 4504 :1969
TABLE2q2. STEEL WELDING NECK FLANGES

Nomind press& 2.5 bar (1 bar = 10' N/my .
NOTE, For nominal iIzes 10 to loo0 usa Tablo 6/2,
1 For weld preparation see

B.S 2633 and B.S.2971or
B.C. 1821 and B.C.2640
"
---- I
1200
1400
1ôW
1220
1420
1620
1375
1575
17%
26
26
26
M27
M27
M27
32
36
40
30
30
30
1320
1520
1730
1245
1445
1645
1 16
16
20
16
16
16
1800
2000
1 m
2020
1990
21%
26
26
M27
M27
44
48
30
30
L 1930
2130
1845
2045 I 20
22
16
16
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : P A R T * 1 69 1624669 0278000 T =
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
BS 4504 : 1969
TABLE 2.5/3. STEEL PLATE FLANGES FOR WELDING
Nominal pressure 2-5 bar (1 bar = lo8N/mv
NOTE. For nominal i h s IO to loo0 uso Table 6/3.
Nom.
size
1 200
1400
1600
1 220
1420
1 620
1375
1575
1790
36
42
46
1280
1480
1 690
5
5
5
M27
M27
M27
36
32I 30
30
30
1320
1520
1730
1800
2000
i a20
2 O20
1990
2190
I
52
58 '
i 890
2090
l
5
5
M27
M27 ;
i */
48
30
30
I
1930
2130

BSI B S * 4 5 0 4 : PART*L b î 3b24bbî 0278003 3
BS 4504 :1969
TABLE 23/11. INTEGRAL*GREYCAST IRON FLANGES

Nominal prekure 2.5 bar (1 bar = 10' N/d)
NOTE.For nominal alzes 10 to loo0 usa Table 6/i 1.
Raked face Neck

Nom
#lu
4 k 4 r
fm.5
---
1200 1375 30 1280 5 M27 32 I 30 1 320 1250 8
1400 1 575 30 1 490 5 M27 36 i 30 1 520 1452 8
1600 1790 32 1 690 5 M27 40 '' 30 1730 1654 10
1800 1990 34 1 890 5 M 27 44 30 1930 1856 10
2000 2 190 34 2090 5 M27 48 30 2 130 2 056 10
2 200 2 405 36 2 295 6 2 340

2400 2 605 38 2 495 6 2 540
2600 2 805 40 2 695 6 2 740
2800 3030 42 2 910 6 2960 2868 12
3000 3 230 42 3 110 6 3 160 3068 12
3200 3 430 44 3 310 6 3 360 3 268 12

3400 3 630 46 3 510 6 3 560 3 472 12
3600 3 840 48 3 720 6 3 770 3 676 12
3800 4 045 48 3 920 6 3 970 3 876 12
4000 4 245 50 4 120 6 4 170 4 076 12
A IJOTE. A l t e r n a t i v e neck form, shown dotted, t o have a maximum d r a f t angle of 12'
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*4504: PART*l 69 l b 2 4 b b î 0278002 3
BS 4504
TABLE 6/2. STEEL WELDING NECK FLANGES

Nominal pressure 6 har (1 bar = lo8N/m*)
I
For weid preparation SPG
B.S.2633and B.S.2971 or
B.S. 1821 and B.S.2640
I J as BDDI
mr I
,is olrrrcd
Aiirrrh, 1971
Nom.
SlZe
Pipe
0.d.
Hange
-- Ralsec
-
IC0
Bolting
DriUIi
-- --
Neck
di D b h 4 f No. di h di hi r
-~ - -- - -- - -
10 17.2 75 12 28 35 2 M 10 4 11 50 26 6 4
15 21.3 80 12 30 40. 2 M10 4 11 55 30 6 4
20 26.9 90 14 32 50 2 M10 4 11 65 38 6 4
25 33.7 100 14 35 60 2 M 10 4 11 75 42 6 4
32 42.4 120 14 35 70 2 M12 4 14 90 55 6 6
40 48.3 130 14 38 80 3 M12 4 14 1cO 62 7 6

50 6093 140 14 38 90 3 M12 4 14 110 74 8 6
65 70-1 160 14 38 110 3 M12 4 14 130 88 9 6
80 88.9 190 16 42 128 3 M 16 4 18 150 102 10 8
100 114.3 210 16 45 148 3 M 16 4 18 170 130 10 8
125 139.7 240 18 48 178 3 M16 8 18 200 155 1c 8

150 168.3 265 18 48 202 3 M 16 8 18 225 184 12 10
200 219.1 320 20 55 258 3 M16 8 18 780 236 15 10
250 273 s'I5 22 60 312 3 M16 12 18 335 290 15 12
300 323.9 440 22 62 365 4 M20 12 22 395 342 15 12
350 355.6 490 22 62 415 4 M20 12 n 445 385 15 12

400 406-4 540 22 65 465 4 M20 16 22 495 438 15 12
450 45712 595 24 65 520 4 M20 16 22 550 492 15 12
.m 508 645 24 68 570 4 M20 20 22 600 538 15 12
600 609g6 755 24 70 670 5 M24 20 26 705 640 16 12
700 711.2 24 70 775 5 M24 24 26 810 740 16 12
800 812.8 975 24 70 880 5 M27 24 30 920 842 16 12
903 9 1414 1075 26 70 980 5 M27 21 30 1 O20 942 16 12
loo0 1016 1175 26 70 1080 5 M27 28 30 1 120 1045 16 16
1 200 1220 1405 28 90 1295 5 M30 32 33 1340 1248 20 16
1400 1420 1Gx) 32 90 1510 5 M33 36 36 1560 1452 20 16
1600 1 620 1830 34 90 1710 5 M33 40 36 1 760 1655 20 16
1800 1 820 2 045 36 100 1 920 5 M36 44 39 1 970 1 855 20 16
2000
-2 O20 2 265
_I_ -- 38
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
110 2 125
- 5 M 39 48 42 2 180 2 058 25 16
21
B S I BS*4504: PART*l b î = lb24bbî 0278003 5
ils 4504 : 1969
TABLE 6/3. STEEL PLATE FLANGES FOR WELDING

Nominal pressure 6 bar (1 bar = lo6 N/m*)
A i altrird
March, 1971
Nom. Drüüng
aim ~-
f I No. h
30 17.2 75 12 35 2 M10 4 11 50
15 21.3 80 12 40 2 M 10 4 11 55
20 26-9 Co 14 50 2 M10 4 ' 11 65
25 33.7 100 14 60 2 M10 4 11 75
32 42.4 120 16 70 2 M 12 4 14 90
40 48.3 130 16 80 3 M12 4 14 100

50 60.3 140 16 90 3 M 12 4 14 110
76.1 16 110 M 12 14 130
A 65
80
100
88.9
114.3
160
190
210
18
18
IZf?
148
3
3
3
M16
M16
4
4
4
18
18
150
170
125 139.7 240 20 178 3 M16 8 18 200

150 168.3 265 20 202 3 M16 8 18 225
200 219.1 320 22 258 3 M16 8 18 280
250 273 375 24 312 3 M16 12 18 335
300 323.9 440 24 365 4 M20 12 22 395
350 355.6 490 26 415 4 M20 12 22 445

400 406 *4 540 28 46 4 M20 16 22 495
450 457.2 595 30 520 4 M20 16 22 550
500 508 645 30 570 4 M20 20 22 600
600 609.6 755 32 670 5 M24 20 26 705
700 711.2 860 34 775 5 M24 24 26 810
800 81243 975 38 880 5 M27 24 30 920

900 914.4 1075 42 980 5 M27 24 30 1 o20
1000 1016 1175 46 1080 5 M27 28 30 1120
1200 1 220 1 405 56 1295 5 M30 32 33 1340
1400 1420 1630 66 1510 5 M33 36 36 1 560
1
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
1600 1620 1830 74 1710 5 M33 40 36 1760

1800 1820 2 045 84 1 920 5 M36 44 39 1970
2000 2020 I 2265 92 2125 5 M39 48 42 2 180
22

BSI B S * 4 5 0 4 : P A R T * 2 67 2624667 O278004 7 m
BS 4504 : 1965
TABLE 6/4, STEEL SCREWED BOSS FLANGES

, Nominal pressure 6 bar (1 bar = louN/rn')
Ali dimendom am In millimetres (exœpt tho inch nomlnal alzo column). Scmwd to ES 21, 'Pipo threads '.
diameter
Nominal a h
- --- I Rihedface
- -
mm b . h I 4
- f
Bolting
No.
-
34 6 10.2 65 10 18 25 2 M10 4 18
w 10
8 13.5
17.2
70
75
10
12
18
20
30
35
2
2
M10
M10
4
4
22
25
96
?4 15 21.3 80 12 20 40 2 M10 4 30
94 20 26.9 90 14 24 50 2 M10 4 40
1 25 33.7 100 14 24 60 2 Ml0 4 50

1% 32 42.4 120 14 26 70 2 M12 4 90 60
1% 40 48.3 130 14 26 80 3 M12 4 100 70
2 50 60.3 140 14 28 90 3 Ml2 4 110 80
2% 65 76.1 160 14 32 110 3 M12 4 130 100
3 80 88.9 190 16 34 128 3 M 16 4 18 150 110

4 100 114.3 210 16 40 148 3 M16 4 18 170 130
5 125 139.7 240 18 44 178 3 M16 8 18 200 160
6 150 165.1 265 - 18 44 202 3 M16 8 18 225
-
185
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*:L 6'7 = Lb24bb9 0278005 9
cS 4504 : 1969
TABLE 6/5. STEEL SLIP-ON BOSS FLANGES FOR WELDING

Nominal pressure 6 bar (1 bar = 10' N/m3
Nom. Flange Driülng I Boss

Bolting
size N
N
D b h dr f 1-
Y dl h dl
- - ~ -
6 10.2 65 10 18 25 2 M 10 4 11 40 18
8 13.5 70 10 18 30 2 M10 4 11 15 22
10 17.2 75 12 20 35 2 M10 4 11 50 25
15 21.3 80 12 20 40 2 M10 4 11 55 30
20 26.9. 90 14 24 50 2 MlO 4 11 65 40
25 33.7 100 14 24 60 2 M 10 4 11 75 . 50
32 42-4 120 14 26 70 2 M12 4 14 90 60
40 48.3 130 14 26 80 3 M12 4 14 100 IO
50 60.3 140 a 14 28 90 3 M12 4 14 110 80
65 76.1 160 14 32 110 3 M12 4 14 130 100
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
80 88.9 190 16 34 128 3 M16 4 18 150 110

100 114.3 210 16 40 148 3 M16 4 18 170 130
125 139.7 240 18 44 178 3 M16 8 18 200 160
150 168.3 265 18 44 202 3 M16 8 18 225 185
200 219.1 320 20 44 258 3 M1C 8 18 280 240
250 273 375 22 44 312 3 M 16 12 18 335 295

300 323-9 440 22 44 365 4 M20 12 22 395 355
- - - 1

BSI B S * 4 5 0 4 : P A R T * & 69 Lb24669 0278006 O W
. BS 4504 : 1969
TABLE 6/& STEEL LOOSE FLANGES FOR WELDED ON LAPPED PiPE ENDS
Nominal pressure 6 bar (1 bar = 10' N/m?
.'
AI alrrrrd
I.' 0
--
.ilarrh, 1971
Flange Drllllag Pipe eod

Pipe -
Nom.
size 0.d.
dl D
-
b 4 8 '
Bolting
No. k '4
max. I r
10 17.2 75 10 . 20 5 M 10 4 11 50 35 3
15 21.3 80 10 24 5 M10 4 11 55 40 3
20 26.9 90 10 30 5 M10 4 11 65 50 3
25 33-7 100 12 37 6 M 10 4 11 75 60 4
32 42.4 120 12 46 6 M12 4 14 90 70 4
40 48.3 130 12 52 G M12 4 14 100 80 4

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
50 60.3 140 12 65 6 M 12 4 14 110 90 5

65 76-1 1M3 12 81 6 M12 4 14 130 110 5
80 88.9 190 14 94 G M16 4 18 150 128 5
100 114.3 210 14 119 6 M16 4 18 170 148 5
125 139.7 240 14 145 6 M16 8 18 200 178 5

150 168.3 265 14 174 6' M16 8 18 225 202 5
33 219.1 320 18 225 8 M 16 8 18 280 258 5
250 273 375 20 279 8 M16 12 18 335 312 5
300 323.9 440 24 330 8 M20 12 22 395 365 5
350 355-6 490 26 362 8 M20 12 22 44s 415 6

400 406.4 540 30 426 8 M20 16 22 495 465 6
450 457.2 595 32 465 8 M20 16 22 550 520 6
500 508 645 32 516 8 M 20 20 22 600 570 6
600 609.6 755 36 618 8 M 24 20 26 705 670 6
700 711.2 860 40 720 8 M 24 24 26 810 775 6
800 812.8 975 44 822 8 M27 24 30 920 880 6

933 914.4 1075 48 926 8 M27 24 30 1 O20 980 6
loo0 1016 1 175 52 1028 8 M27 28 30 1 120 1080 6
1 200 1 220 1405
-
€0 1 232 -
10 M30 32 - 33 1340 1 295 8

- _y-
BSI B S X 4 5 0 4 : P A R T 8 1 6 9 l b 2 4 6 6 9 0278007 2 =
BS 4504 : 1969
TABLE 6/& STEEL PLATE BLANK FLANGES

Nominal pressure 6 bar (1 bar = 10' N/m*)
NOTE. The two types of flanges shown are alternatives at the option of the manufacturer.
Form B Form C
As altrrrd
Marrh. 1971
__ ~~ ~ ~~~
Nom.
size
Flange
Bolting
Drilling
--
D b No. h
- 4 11 !io
10
15
75
'80
12
12 ' - M10
M 10 4
4
11
11
55
65
20
25
90
100
14
14 --
4 M10
M 10 4
4
* 11
14
75
90
32 120 14 . M12
40 130 14 - M 12 4 14 1c3
50 140 14 - M12 4 14 110
65 160 14 55 M12 4 14 130
80 190 16 70 M16 4 18 150
100 210 16 90 M16 4 18 170
125 240 18 115 M16 8 18 200

350 265 18 140 M16 8 18 225
175 295 20 165 M 16 8 18 255
200 320 20 190 M 16 8 18 250
250 375 22 237 M 16 12 18 335
300 440 22 285 M20 12 22 395

350 490 22 332 M20 12 22 445
400 540 22 380 M20 16 I 22 495
450 - 595 24 428 M20 16 1 22 550
500 645 24 475 M20 20 I 22 600
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : P A R T * 1 69 1624669 0278008
TABLE 6/11. INTEGRAL GREY CAST IRON FLANGES

Nominal pressure 6 bar (I bar 10' N/m*)
A r alirrrd
M u r c h , 1971
Flange Ralscd face Drilling Neck

Xom. Bolling -- --
she
P I b No. da k
--- da r
10 75 12 35 2 M10 4 11 50 26 3
15 80 12 40 2 M 10 4 11 55 31 3
20 90 14 50 2 M 10 4 11 65 38 4
25 60 2 M10 4 11 75 47 x 4
32 70 2 M12 4 14 90 56 4
40 80 3 M12 4 14 100 64 4
50 90 3 M 12 4 14 110 74 4
65 110 3 M12 4 14 130 89 4
ao 190 18 128 3 M 16 4 18 150 108 5
100 210 18 148 3 M 16 4 18 170 128 5
125 240 20 178 3 M16 8 18 200 155 5
150 265 20 202 3 M16 8 18 225 180 5
200 320 22 258 3 M16 8 18 280 234 6
250 375 24 312 3 M16 12 18 335 286 6
300 440 24 365 4 M20 12 22 395 336 6
350 490 26 415 4 M 20 12 22 445 390 8
400 540 28 465 4 A120 16 22 495 442 8
550 595 30 520 4 M20 16 22 550 492 8
500 645 30 570 4 M20 20 22 600 546 8
600 755 30 670 5 M 24 20 26 705 646 8
7co 32 775 5 M 24 24 26 810 748 10
i
800 975 34 880 5 M 27 24 30 920 852
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
10
900 1075 980 5 M27 24 30 1 O20 954 10
loo0 1175 36 : 1 080 5 M 27 28 30 1120 1054 10
1 200 1 405 40 1 295 5 M30 32 33 1340 1 260 10
1 400 1630 44 1510 5 M33 36 36 1560 1466 12
1600 1830 48 1710 5 M33 40 36 1760 1672 12
1 800 2 045 50 1 920 5 M 36 44 39 1970 1876 15
2OKJ 2 265 54 2 125 5 M39 48 42 2 180 2 082 15
2 200 2 475 60 2 335 6 M 39 52 42 2 390 2 290 15
2 400 2 685 62 2 545 6 M39 56 42 2600 2 494 18
2 fi@? 2 905 64 2 750 6 M45 60 48 2 810 2 696 18
2 893 3 115 68 2960 6 M45 64 48 3 O20 2902 18
soo0 3 315 70 3 160 6 M45 '68 48 3 220 3 106 18
3 200 3 525 76 3 370 6 M45 72 48 3 430 3 314 18
3 400 3 735 80 3 580 6 M45 76 48 3 640 3 520 20
3 m 3970 f a4 3 790 6 M 52 80 56 3 860 3726 i 20

BSI B S * 4 5 0 4 : P A R T 8 1 69 Lb24669 0278009 b
TABLE 6/12. MALLEABLE CAST IRON INTEGRAL FLANGES

Nominal pressure 6 bar (1 bar = 106 N/rna)
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Nom. Flange I 1-
Rghedface
Bolting
Drilling Neck
a
h
10
D
75 9 35
f
2
I
M10
No.
4
da
11
-
50
k da
26
-__-
r
3
15 80 10 40 2 M10 4 11 55 31 3
20 90 10 50 2 M10 4 11 65 38 4
25 100 11 60 2 M10 4 11 75 47 4
32 120 11 70 2 M12 4 14 90 56 4
40 130 12 80 3 M12 4' 14 100 64 4

50 140 12 90' 3 M12 4 14 110 74 4
65 160 13 110 3 M12 4 14 130 89 4
80 193 13 128 3 M16 4 18 150 108 5
100 210 15 148 3 M16 4 18 170 128 5
125 240 17 178 3 M16 8 18 200 155 5

150 265 17 202 3 M16 8 18 225 180 5
-
/A
-- idOTE, Alternative nec!; foxpi, ehovtri Clotted, t o have a m a x i m u draft angle of 12'
...

B S I BS84504: PART83 69 m 3 6 2 4 6 6 9 0278030 2 m
TABLE 6/13. MALLEABLE CAST IRON SCREWED BOSS FLANGES

Nominal pressure 6 bar (1 bar = 10' N/m*)
All dimensions are in millimetres (except the inch nominal size column). Screwed to BS 21. ' Pipe threads *.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
'+ Taper 1:6*25on diameter
As ulrerrd
Alurrh, 1971
Drilling
Bolting
No. 4 k
10.2 65 8 15 M 10 4 11 40 ia
13.5 70 a 15 M 10 4 11 45 22
17-2 75 9 17 M10 4 11 50 26
21.3 80 10 17 M 10 4 11 55 32
26.9 90 ' 10 19 M10 4 11 65 38
1 25 33.7 100 11 20 M10 4 11 75 46
1% 32 42.4 120 11 22 M12 4 14 90 56
1% 40 48.3 130 12 22 M12 4 14 100 63
2 50 60.3 140 12 26 M12 4 14 110 77
236 65 76.1 160 13 31 M12 4 14 130 92
88-9 190 13 34 M16 4 ia 150 106
114-3 210 15 40 M 16 4 ia 170 132
139.7 240 17 44 M16 8 18 200 160
165.1 265 M16 8 18 225 185

IS 4504 : 1969

Nominal pressure 10 bar (1 bar = lo5N/m9)
NOTE. For nominal sizes 10 to 175 use Table 16/2.
1 For weld Dreoaration see

B . S . 2 6 3 3 ’ a n d B.S.2971 or
8.S. 1821 and B.S.2640
I J as a m r o o r i a t e
k
D
4 w
I !
Nom. --
Flnnge Rslsed face
-- BolIlna
Drilling Ncek
size
I !TT Ï
- , - I -
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
D b h, f No. d, I h r
I
- -- - _----___- i 2 ,
-
16 I 10
I
M 20
200
250
219.1
273
340
395
24
26
62
68
268
320
3
3 M20
’
i
8
12
22
22 1 295’
350 ’
235
292
1 16 ! 12
300 323-9 445 26 68 370 4 M 20 I 12 22 I 400 ! 344 16 12
350 355.8 505 26 68 430 4 M20 i 16 [ 22 i 460 385 1 16 . 12
4 1 ,lll~lt~d
400 406.4 565 26 72 482 4 M24 ’! 16 j 25 I 515 I 440 1G 13
Jiiiiuury 1972 450 457.2 615 28 73 532 4 M 24 20 26 565 493 ; IG . II
‘ I
500 508 670 28 75 585 4 M 24 20 ; 26 ’ 620 ’ 542 I 16 , 12
600 609-6 780 28 80 685 5 h127 20 ‘ 30 725 ’ 642 ; 18 ! 12
700 711-2 895 30 80 800 5 M27 24 . 30 840 745 i 18 ! 12
800 812.8 1015 32 90 905 5 M 30 24 I 33 , 950 850 ‘ 18 12
900 91444 1115 34 95 1 005 5 M30 28 I 33 , 1050 . 950 i 20 ’
12
i
loo0 1016 1230 34 95 1110 5 M33 28 i 36 : 1160 1052 I 20 16
1 200 1 220 1455 38 115 1330 5 M36 32 , 39 1380 1255 25 :
16
1400 1420 1675 42 120 1 535 5 hl 39 36 . 42 ’ 15’30 1460 i 25 , 16
1600 1620 1915 46 130 1760 5 i hl45 40 48 1820 1665 25 16
1 800 1 820 2 115 50 140 1960 5 i M45 44 48 2020 1868 30 16
I
2000 I 2020 I 2325

- 54 150 I 2170 5 i h145 , 48 48 2230 2072 30 1G

Provided
f by IHS Markit under license with BSI - Uncontrolled Copy Licensee=Hong Kong Polytechnic University/9976803100, User=WONG, Kit Chun
B S I BS*4504: PART*3 b ï m 3b24bbî 0278032 b
BS 504 : 1969 I
TABLE lop.STEEL PLATE FLANGES FOR WELDING
Nominal pressure 10 bar (1 bar = los N/m*)
NOTE. For nomlnnl sizes 10 to 175 use Tnblc M/3.
-
Nom. Fiange Raked face Drilling
yize I Bolting
D l b No. k
200 219.1 340 24 268 M20 8 295

250 273 395 26 320 M20 350
300 323.9 445 26 370 M20 400
350 355-8 505 28 430 M20 16 460
400 406-4 565 32 482 M24 16 515
450 457.2 615 36 532 M 24 20 565 Ar n l t r d
Juniary 197:
500 508 670 38 585 M24 20 620

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
600 609.6 780 42 685 M27 20 725

700 711.2 895 46 800 M27 24 840
am 812.8 1015 52 905 M30 24 950
900 914.4 1115 56 1005 M30 28 33 1050
loo0
1 200
1016
12-20 i 1230
1455 :
62
74 I 1110
1330 I 5 I M33
M36
28
32 39
1160
1380

BSI B S * V 5 0 V : PART*<L 6 9 162Libbî 0278013 8 W
1969
TABLE 1015. STEEL SLIP-ON BOSS FLANGES FOR WELDING

Nominal pressurê 10 bar (1 bar = 10’ N/ma)
NOTE. For nominal sizes 6 to 65 mm inclusive uso Table 16/5.’
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
As alrrrrd
March, 1971
I
Nom.
ao
121 ?i!:
88-9
D
200
Flange
-
b
-
h
u)
-4
-
f
34
Ralsedrace
138 3
Bolting
M16
--I
-No,
8
Drilling
4
18
1
--
160 118
100 114.3 220 20 40 158 3 M16 8 18 180 140
125 139.7 250 22 44 188 3 . M16 8 18 210 168
. 150 168.3 285 22 44 212 3 M20 8 22 240 195
200 219.1 340 24 44 268 3 M20 8 295 247
250 273 395 26 46 320 3 M 20 350 292

300 323.9 445 26 46 370 4 M20 12 400 344
- I -- I

~ ~~
BSI B S * 4 5 0 4 : PART*1 b î 1 6 2 4 b b î 0278014 T
TABLE 10/6. STEEL LOOSE FLANGES FOR WELDED ON LAPPED PIPE ENDS
Nominal pressure 10 bar (1 bar = 106 N/m*)
I L ! ,il
*edfor
4301
Ar olrrrrd
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
hlnrrh, 1971 '
Nom. Pipe
0.d.
Finnge i DriUing 1 Pipeenà
sire
dl D b k $1
r
max.
-
10 17.2 90 14 M12 4 14 60 40 3
15 21.3 95 14 M12 4 14 65 45 3
20 26.9 105 14 M 12 4 14 75 58 3
25 33-7 115 16 M12 4 14 85 68 4
32 42.4 140 16 18 100 78 4
40 48.3 150 16 18 110 88 4
50 60.3 165 16 65 6 M 16 4 18 125 102 5
65 76.1 185 16 81 6 M 16 4 18 145 122 5
80 88.9 200 18 94 6 M 16 a 18 160 138 5
100 114.3 220 18 18 180 158 5
125 13907 250 18 18 210 188 5
150 168.3 285 18 22 240 212 5
200 219.1 340 20 22 295 268 5
250 273 395 22 22 350 320 5
200 323.9 445 26
M20 I l2 i 22 I
I
400 370 5
-

BSI B S X 4 5 0 4 : P A R T U L 69 Lb24669 0 2 7 8 0 3 5 L
us 4504 : 969
TABLE 10/8. STEEL PLATE BLANK FLANGES

Nominal pressure 10 bar (1 bar =I lo6N/ml)
NOTE 1. The two types of flanges shown arc alternatives al the option of the manufacture.
NOTE 2. For nominal shes 10 to 175 usc Table 16/8.
Form B Form C
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
I5
200 340 24 190 M20 8 22 295

250 395 26 237 M20 12 22 350
300 445 26 285 M20 12 22 400
350 505 26 332 M20 16 22 460
400 565 26 380 M24 16 26 515
As added 428
January I972 450 615 28 M24 20 26 565
500 I 670 I 28 . 1 475 M24 1 20 1 26 1 620

BSI B S * q 5 0 4 : P A R T * L 69 Lb24669 027BOlb 3
BS 4504 ; 19U9
TABLE lO/ll. INTEGRAL GREY CAST IRON FLANGES

Nominal pressure 10 bar (i bar = 10' N/m*)
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Nom. 1 mange Raked face Drilling Neck
b 4 Li.
Bolting
I No. k 4 r
26 268 3 M20 8 22 295 240 8

250 395 28 320 3 M20 12 22 350 292 8
300 445 28 370 4 M20 12 22 400 342 8
350 505 30 430 4 h120 16 22 460 396 8
400 565 32 482 4 Ai24 16 26 515 448 10
450 615 32 532 4 M24 20 26 565 498 10

500 670 34 585 4 M24 20 26 620 552 10
600 780 36 685 5 M27 20 30 725 654 10
700 895 40 800 5 M27 24 30 840 760 10
800 1015 44 905 5 M30 24 33 950 866 12
46 1 005 5 M30 28 33 1 050 970 12

50 1110 5 M 33 28 36 1160 1 076 12
1 200 1455 56 1330 5 M36 32 39 1380 1 284 15
1 400 1675 62 1 535 5 M 39 36 42 1590 1494 18
68 1760 5 M45 40 48 1820 1 702 18
1 800 70 1960 5 48 2 020 1906 18
2 m 2 325 74 2 170 5 48 2 230 2 112 18
2 200 2 550 80 2 370 6 56 2 440 2 320 20
2 400 2 760 82 2 570 6 56 2 650 2 524 20
2 GOO 2 960 88 2 780 6 56 2 850 2 732 20
2 800 3 180 ; 94 300 6 56 3 070 2 940 20
3000 3405 I 100 3 210 6 62 3 290 3 150 20
A NOTE. Alternative neck form, shown dotted, t o have a maximum draft angle of 12'

BSI BS*4504: PART*3 6 7 3624667 0278037 5
ils 4504 : 1969
TABLE 16/L INTEGRAL STEEL FLANGES

Nominal pressure 16 bar (1 bar = 10' N/rn2)
Nom. Fiange Raised face Drilling

size Bolting
D b i No. d: r
65 185 18 122 3 M16 4 18

80 200 20 138 3 M16 8 18
100 220 20 158 3 M16 8 18
125 250 22 188 3 M16 8 18 210 159
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
150 285 22 212 3 M20 8 22 240 184
175 315 24 242 3 M20 8 22 270 211

200 340 24 268 3 M20 12 22 295 236
250 405 26 320 3 M24 12 26 355 290
300 460 28 378 4 M24 12 26
350 520 30 438 4 M2.l 16 26
,iddid
400 580 32 490 4 M27 16 30 525 ' 448 10
Jriiiuury 1972 450 640 34 550 4 M 27 20 30 585 502 10
50 715 36 610 4 k130 20 33 650 554 10
600 840 40 725 5 M33 20 36 770 660 10
700 910 42 795 5 h.133 24 36 * 840 760 12
800 1025 42 900 5 M36 24 39 950 664 12 1
900 1 125 44 1000 5 M36 28 39 1050 966 12
loo0 1255 46 1115 5 M39 28 42 1170 1070 12
1 200 1485 52 1330 5 M45 32 48 1 390 1278 15
1400 1685 58 1530 5 M45 36 48 1 590 1488 15
1600 1930 64 1750 5 M52 40 56 1820 1696 18
1800 2 130 68 1 950 5 M52 44 56 2 O20 1902 18

2000 2 345 70 2 150 5 M56 48 62 2 230 2 106 18
2 200 2 555 74 2360 6 M56 52 62 2 440 2 312 18

BSI BS*95OY: P A R T * 1 69 1624669 02780l18 7
BS 4504 : 1969

Nominal pressure 16 bar (1 bar = 10' N/rn*)
I For weld preparation see

* EIS2633 and B.C.2971 or
. 8.C.1821 and B.S.2640
L( as appropriate
- - - - t - L t I VA n,
D
Ar alirrrd
Slarrh, 1971
Nom.
size
Raked face
L__
4
1- biting --
No.
Drilling 1 Neck
--
lo 40 2 M12 4 14 60 28 6 4
15 21 -3 45 2 M12 4 14 65 32 6 4
20
25
32
26.9
337
42.4
I
.
105
115
140
16
16
16
38
38
40
58
68
78
2
2
2
M 12
M 12
M 16
4
4
4
14
14
18
75
85
100
40
46
56
6
6
6
4
4
6
40 48.3 150 16 42 88 3 M16 4 18 110 64 7 6
50 60.3 165 18 45 102 3 M16 4 18 125 75 8 6
65 76.1 185 18 45 122 3 M16 4 18 145 90 10 6
80 88*9 200 20 50 138 3 M 16 8 18 160 105 10 8
100 114.3 220 20 52 158 3 M16 8 18 180 131 12 8
1?5 139.7 250 22 55 188 3 M16 8 18 210 156 12 8

150 168.3 285 212 3 M20 8 22 240 184 12 10
I i
175 193.7 315 21 60 242 3 M20 8 22 270 210 12 10
200 219.1 ~ 340 62 268 3 M20 12 23 295 235 16 10
250 213 ! 405 26
24 70 320 3 M24 12 26 355 25 16 12
300
350
523.9
355.6
I
[ 460
520
28
30
78
82
!
j
378
438
4
4
1 M24
M24
ia
16
26
26
410 344 16 12
400 4064 ' 580 32 85 I 490
!
1
I
4 I M27 16 30
470
525
390
445
16
16
12
12 AI added191
January
150
500
600
457.2
508
609.6
0
,
640
715
840
34
34
36
87
90
'
¡
550
610
4
4
5
I M27
M30
M33
20
20
20
30
33
36
585
650
770
.
496
548
652
16
16
18
12
12
12
700 711.2 I 910 36 5 M33 24 36 a40 755 18 12
800 812.8 1025 38 5 M36 24 39 950 855 20 12
300 914.4 1125 40 5 M36 28 39 1050 955 20 12
loo0 1016 1255 42 120 1115 5 MJ9 28 42 1170 1058 22 16
1 200 1220 1485 48 130 1330 5 M45 33 4a 1390 1262 30 16
1400 1 420 1685 52 145 1530 5 M45 36 48 1590 1465 30 16
1 boo 1620 1930 58 5 M 52 40 56 1820 1668 35 16 .
1 800 1820 2 130 62 44 56 2020 1870 35 16
---
2003 2 O20 2 345 66
--48 - 62 2230 2072
-
40
- 16
37
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

B S I BS*4504: PART*L 69 = lb24669 0278037 9 =
BS 4504 : 1969
TABLE 16/3. STEEL PLATE FLANGES FOR WELDING
Nominal pressure 16 bar (1 bar 10' N/m*)
. .
Pipe Flange Ratted face Drilling

Nom. 0.d. Bolting
a h
dl D b f NO. k
~
10 17-2 90 14 40 2 M12 4 14 60
15 21.3 95 14 45 2 M12 4 14 65
20 26.9 105 16 58 2 M12 4 14 75
25 33.7 115 16 68 2 M12 4 14 85
32 42.4 140 16 78 2 M16 4 18 100
,
40 48a3 150 16 88 3 M16 4 18 110
50 00.3 165 18 102 3 . M16 4 18 125
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
65 76.1 185 18 122 3 M16 .4 18 143
80 88.9 200 20 138 3 M16 8 18 160
100 114.3 220 20 158 3 MIG 8 18 180
125 139.7 250 22 188 3 M 16 8 18 210

150 168.3 285 22 212 3 M20 8 22 240
175 193.7 315 24 242 3 M20 8 22 270
200 219.1 340 24 268 3 M20 12 22 295
250 273 405 26 320 3 M24 12 26 355
300 323.9 460 28 378 4 M24 12 26 410

350 355-6 520 32 438 4 M24 16 26 470
400 406.4 580 36 490 4 M27 16 30 525
A i addcd
Junuary 1972 450 457.2 640 40 550 4 M27 20 30 585
500 508 715 44 610 4 M30 20 33 650
600 609-6 840 52 725 5 M33 20 36 770
700 711.2 910 58 795 5 M33 24 36 840

800 81243 1025 64 900 5 M36 24 39 950
wo 914-4 1 125 72 lo00 5 M36 28 39 1050
loo0 1016 1255 78 1115 5 M39 28 42 1170
1 200 1220 1485 94 1330 - 5 M45 32 48
--
1 393

BSI B S * 4 5 0 4 : PART*L 69 Lb24669 0 2 7 8 0 2 0 5 =
BS 4504 : i969
TABLE 16/4. STEEL SCREWED BOSS FLANGES
Nominal pressure 10 and 16 bar (1 bar = 106 Wm9
All dimendona are In milllmetres (except the inch nominal alza column). Screwed to BS 21, ' Pipa threads *.
diameter
AI afirrtd
hfarrh. 1971
I I.' k
I
---
Nomlnal size Flange I Ralsedface
in I mm N D b
~~ 3___- --
?4 6 10.2 75 12 18 32 2 M10 4 11 50 20
?4 8 13.5 80 12 18 38 2 M10 4 11 55 25
94 10 17.2 90 14 20 40 2 M12 4 14 60 30
w 15 2163 95 14 20 45 2 M12 4 14 65 35
w 20 26.9 105 16 24 58 2 M12 4 14 75 45
1 25 33.7 115 16 24 63 2 M12 4 14 85 52
1% 32 42.4 140 16 36 78 a M16 4 18 100 60
1% 40 48.3 150 16 26 88 3 M 16 4 18 110 70
2 50 60.3 165 18 28 102 3 M16 4 18 125 85
2% 65 76.1 185 18 32 122 3 M16 4 18 145 105
3 80 88.9 200 20 34 138 3 M16 8 18 160 118
4 100 114.3 220 20 40 158 3 M16 8 18 180 140
5 125 139.7 250 22 44 188 3 M16 ' 8 18 210 368
6 150 165-1 285 22 44 212 3 M20 8 22 240 195
I -
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
39

BSI BS*4504: PART*3 b î l b 2 4 6 6 9 0278023 7
I
.IS 4504 : 1959
TABLE 16/5. STEEL SLIP-ONBOSS FLANGES FOR WELDING

Nominal pressure 16 bar (i bar = lO'N/m*)
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
eter
As alrrrrd
March, 1971
:!r I-
I I
Nom. ;tange Drnllng Boss

alae d.
b TI 4 f i NO, 4 It
6 10.2 75 12 2 M10 4 11 50 20
8 13-5 80 12 2 MlO 4 11 55 25
10 17-2 90 14 2 Ml2 4 14 60 30
15 21.3 95 14 20 45 2 Ml2 4 14 65 35
20 26-9 105 16 24 58 2 M12 4 14 75 45
25 33.7 115 16 24 68 2 M12 4 14 85 52
32 42.4 140 16 26 78 2 M 16 4 18 100 60
40 48-3 150 16 26 88 3 M16 4 18 110 70
50 60.3 165 18 28 102 3 M16 4 18 125 85
65 76.1 185 18 32 122 3 M16 4 18 145 105
80 88.9 2oos 20 34 138 3 M16 8 18 €lQ 118
100 114.3 220 20 40 158 3 M16 8 18 180 140
125 139-7 250 22 44 188 3 M16 8 18 210 168
150 168.3 285 22 44 212 3 M20 8 22 240 195
200 219.1 340 24 44 260 3 M20 12 n 295 247
250 273 405 26 46 320 3 M24 12 26 355 300
300 323.9 460 28 46 378 4 M24 12 26 410 355
I
-
40

~
P A R T S 1 69 m 1624bb9 0278022 9
BS 4504 ; 1969
TABLE 16/& STEEL PLATE BLANK FLANGES
Nominal pressure 16 bar (i bar = IO8 N/m*)
NOTE. The two types of flanges shown aro altcmativts at the option of the manufacturer.
Form 0 Form C
icIi 4
k-+I
k
? b
4 0 -P
1 I
Nom. Flange
aim
b k
10 90 14 - M12 4 14 60
15 95 14 - M 12 4 14 65
2" 105 16 - M12 4 14
-
75
25 115 16 - M12 4 14 85
32 140 16 - M16 4 18 100
40 150 16 - M16 4 18 110
50 165 18 - M16 4 18 125
65 185 18 55 M16 4 18 145
80 200 20 70 M16 8 18 160
100 220 -20 90 M 16 8 18 180
125 250 22 115 M16 8 18 210
150 285 22 140 M20 8 22 240
175 315 24 165 M20 8 22 270
200 340 24 190 M20 12 22 295
250 405 26 237 M24 12 26 355
300 460 28 285 M24 12 26 410
350 520 30 332 M24 16 26 470
400 580 32 380 M27 16 30 525
450 640 34 428 M27 20 30 585 As addrd
January i972
500 715 36 475 M30 I 20 33 . 650
41
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

ßS 4504 : 1969

Nominal pressure 16 bar (1 bar = 106 N/ms)
Nom. Flange Raked face Neck

Bolting
Size
D 6
10 90 14 40 2 M12 4 14 60
15 95 . 14 45 2 M 12 4 14 65
20 105 16 58 2 M 12 4 14 75
25 115 16 68 2 M12 4 14 85
32 140 18 78 2 M 16 4 18 100
I
40 150 18 88 3 M16 4 18 110
50 165 20 102 3 M16 4 18 125
65 185 20 122 3 M16 4 18 145
80 200 22 138 3 M 16 8 18 160
100 220 24 158 3 M16 8 18 180
125 250 26 \ 188 3 M16 8 18 210

150 285 26 212 3 M20 8 22 240
175 315 28 242 3 M20 8 22 270 217 8
200 340 30 268 3 M20 12 22 295 246 8
250 405 32 320 3 M24 12 26 355 298 10
300 460 32 378 4 . M24 12 26 410 348 10

350. 520 36 438 4- M24 16 26 470
400 580 38 490 4 M27 16 30 525
450 640 40 550 4 M27 20 30 585 510 10
500 715 42 610 4 M30 20 33 650 564 12
600 840 48 725 5 M33 20 36 770 672 12

700 910 54 795 5 M33 24 36 840 764 12
800 1025 58 900 5 M36 24 39 . 950 870 12
900 1125 62 loo0 5 M36 28 39 1 050 976 12
loo0 1 255 66 1115 5 M39 28 42 1 170
l!& NOTE. Alternative neck form, Bhown dotted, to have a maximum draft angle of 12'
42
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

Nominal pressure 10 bar and 16 bar (1 bar 10' N]m') -
Fiange Raised face Drilling
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
size Boltlng
b f No. I 48 h
14 40 2 M12 4 14 60
15 14 . 45 2 M12 4 14 65
20 105 16 58 2 M12 4 14 75
25 115 16 68 2 M12 4 14 85
32 140 16 78 2 M16 4 18 100
16 * 88 3 M16 4 18 110
50 18 102 3 M16 1 18 125 80 5
65 I 185 18 122 3 M16 4 18 145 95 5
80 zoo 20 138 3 M16 8 18 160 114 6
20 158 3 M16 8 18 180 136 6
I
125 i 250 22 , 188 3 M16 8 18 210 165 8
150 i 285 . 22 3 M20 8 22 240 190 8
I I
43

BSI B S * 4 5 0 4 : P A R T * 1 69 = 1624669 0278025 4
ß S 4504 :1969
TABLE 16/13. MALLEABLE CAST IRON SCREWED BOSS FLANGES

Nominal pressure 10 bar and 16 bar (i bar = 10' N/m*)
All dimcnslons aro In millimctns (except the Inch nominal sizo column). Screwed to BS 21, ' Pipe threads *.
per I :6.25 on didmeter
?4 6 10.2 75 12 18
Boltlag
M10
1 No.
4 11 i 50
w 8 13.5 80 12 18 M10 4 11 55
36 10 17.2 90 14 20 M12 4 1 4 i 6 0 1 3 0
34 15 21*3 95 14 20 M12 4 14 65 i 35
w 20 26.9 105 16 24 M12 4 14 75 1 45 i
1 25 33-7 115 16 24 MI2 4 14 85 ! 52
1% 32 42.4 140 16 26 M16 4 18 i 100 ' i 60
1% 40 48.3 150 16 26 M16 4 18 110 70
2 50 60.3 165 18 28 M16 4 18 i 125
2% 65 76.1 185 18 32 M16 4 18 1: 145
3 80' 88.9 200 20 34 M16 8 18 - 150 118
4 100 114.3 220 20 40 M16 8 18 180 140
5 125 139-7 250 22 44 M16 8 18 210 ! 168
6 150 165-1 285 22 44 M 20 8 22 210 I 195
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
44

E S 1 BS*4504: PART*L 69 = Lb24bbï 0278026 b
9s 4504 : 1963
TABLE W/l. INTEGRAL STEEL FLANGES
Nominal pressure 25 bar (1 bar = 10' N/rn*)
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
NOTE. For.nomlnal skes 10 mm to I50 mm use Table 40/1.
I
~ ~~
Nom. mange Raised face Drillhg Neck
I D b f
Bolting
k dt
--
r
175 330 28 248 3 M24 12 26 280 217 8

200 360 30 278 3 M24 12 26 310 246 8
250 425 32 335 3 M27 12 30 370 298 10
300 485 34 395 4 M27 16 30 430 352 10
350 555 38 450 4 M30 16 33 490 408 10
400 620 40 505 4 M33 16 36 550 460 10

Ar added 450 670 42 555 4 M 33 20 36 600 514 12
J a y a r y 1972
500 730 44 615 4 M33 20 36 660 566 12
600 845 46 720 5 M36 20 39 770 670 12
700 960 50 820 5 M39 24 42 875 776 12
800 lo85 54 930 5 M45 24 48 990 882 15
900 1185 58 1030 5 M45 28 i 48 1090 988 15

1000 1 320 62 1140 5 M 52 28 1094 18
1200 1530 70 1350 5 M 52 32 1 306 18
1400 1755 76 1560 5 M56 36 62 1640 1514 18
1600 1975 84 1 780 5 M56 40 62 1860 1726 20
1800 2 195 90 1 985 5 M64 44 1936 20

2000 2 425 96 2 210 5 M64 48 2 144 20

ES 4204 : 1969

* Nominal pressure 25 bar (i bar = lo5 N/m')
NOTE. For nominal siles 10 mrn to 150 m m use Table 40/2.

B.S. 2 6 3 3 and 8.S.2971 or
B.S. 1821 and B.S.264@
--Flange
--- -Bolting - -
Raked face Drilling I Neck
-- -
ha
-- --h l - - - -
D b dc f No. r
da
-% -
175 193.7 330 28 75 248 3 M 24 12 26 280 218 15 10
200 219.1 360 30 80 278 3 M24 12 26 310 244 16 10
250
300
273
323.9
425
485
32
34
88
92
335
395 I 3
4
M27
M27
12
16
30
30
370
430
298
352
18
18
12
12
350 355.6 555 38 100 450 4 M30 16 33 490 398 20 12
400 406.4 620 40 110 505 4 M33 16 36 550 452 20 12

457.2 555 505 As added192.
January
450 610 42 110 4 M33 20 36 600 U) 12
500 508 730 44 125 615 4 M33 20 36 660 558 20 12
600 609.6 845 46 125 720 5 M36 20 39 770 660 20 12
700 711.2 960 46 125 820 5 M39 24 42 875 760 20 12
8íXl 12
1
812.8 1085 50 135 930 5 M45 24 48 99(j 865 22
900 914.4 1185 54 145 1030 M45 28 48 1090 968 24 12

loo0 1016 1320 58 -
155 1140 5 M52 -
28 56 1210 I 1070
-
24
-
16
47
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*KL bï 3b24bbï 0278028 T
ns 4504 : 1969
TABLE S/3. STEEL PLATE FLANGES FOR WELDING
NomInal pressure 25 bar (1 bar = 10' N/m3
NOTE For nominal rizcs 10 m m lo 1Mm m use Table 40/3.
Drillhg
Nam.
Site P
o
rl Flange hlsed face
Bolting --
4 D b r, I r k
-
175 193.7 330 26 248 3 M24 280
200 219-1 360 2.8 278 3 M24 310
250 273 425 32 335 3 M27 12 370
300 323.9 485 38 395 4 M27 16 30 430
350 355.6 555 42 450 4 M30 33 490
400 406.4 620 46 505 4 ! M33 16 36 550

Ar added
457.2 670 52 555 4 ' M33 Mjo
Jitnuary 1972 450
500
600
508
õO9.6
730
845
58
66
615
720
4 1 M33 660
770
48
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

ES1 B S * 4 5 0 4 : PART*l 69 Lb24669 0278029 1 =
BS 4504 : 1969
TABLE 25/5. STEEL SLIP-ON BOSS FLANGES FOR WELDING

eter
As alrrrrd
hiarch. 1971
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
I
-
lange Rsbedface
-- Boss
D b h
~~
6 10.2 75 14 20 32 2 M 10 4 11 50 20
a 13.5 ao 14 20 38 2 M10 4 11 55 25
10 17.2 90 16 22 1 40 2 M12 4 14 60 30
15 21.3 95 16 22 45 .2 M 12 4 14 65 35
;i
20 26.9 105 ia 26 58 2 M12 4 14 75 45
25 115 ia 2 M 12 4 14 52
i
33.7 85
32 42.4 140 18 2 M16 4 18 100 60
40 48.3 150 18 102 3 M 16 4 18 110 70
50 60.3 165 20 3 M16 4 ia 125 85
65 76.1 185 22 38 122 3 M16 a 18 145 105
250 24 40 138 3 M16 a ia 160 118
235 24 44 162 3 M26 a 22 190 145
no 26 48 188 3 M24 a 26 220 170
300 28 52 218 3 M24 a 26 250 200
360 32 52 278 3 M24 12 26 310 256
425
485
40
48
60 I 335
395
3
4
370
430
310
364
- 67 I - 1

ES1 BS*4504: P A R T * I 6 9 l b 2 4 b b î 0278030 8
DS 4504 : 1969
TABLE ZS/8. STEEL PLATE BLANK FLANGES
Nominal pressure 25 bar (1 bar = los N/m')
NOTE 1. Thc twu -.ypes o f flango shown are altcrnativcs at thc option o f thc manufacturer.
NOTE 2. For nomi' QI sizes 10 inm to 150 mm usc Table 40/8.
Form B Form C
Nom. Flange
size
26 280
26 310
250 237 12 30 370
300 16 30 430
350 555 332 M30 16 33 490
400 620 40
Ar added 450 670 42
January 1972
500 730 45
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

E S 1 BS*4.504: P A R T * 3 69 3624669 0278033 T m
BS 4504 : 1969
-
. Nominal prcssurc 25 bar (1 bar 10' N/m3
k U
Ai dirrrd
\/tirch. I Y I I
Nom. Flange Neck
J8 P
30 4
15 37 4
20 44 5
25 115 68 M 12 85 cd 5
32 140 hí16 18 100 62 5
40 15@ 20 aa M16 18 110 70 5

50 155 102 M 16 18 125 84 6
GS ia5 122 3 M 16 a 18 145 101 6
80 200 26 138 3 M16 a 18 160 120 6
100 235 28 162 3 M20 a 22 190 142 6
125 270 30 188 M24 B 26 220 171 6

150 399 34 218 M 24 8 26 250 202 8
175 330 34 248 M24 12 26 280 223 10
203 360 34 278 M24 12 26 310 252 10
250 425 3G 335 M27 12 30 370 304 10
303 435 40 395 4 M27 16 30 430 360 10
hí 30 16 33 490 416 12
400 M33 16 36 550 l2 As addt.d
4 50 670 555 20 36 600 January 1972
503 733 615 20 36 660 578 15
/5\ WOT!3. Alterh&tAve neck r'orm, ehown ùotted, t o have a maximum àraft angle of 12''
I . ..
'
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S X 4 5 0 4 : P A R T X L b 7 m L b 2 4 b b 9 0 2 7 8 0 3 2 L m
ES 4504 : 196Y

Nominal pressure 25 bar (1 bar = IO6 Nlm')
Nom. Neck
Si20
~~
da I r
10 90 16 40 M12 4 14 60 4
15 95 16 45 4 14 65
20 105 18 58 2 4 14 75 44 5
25 115 18 68 2 M12 4 14 85
I
32 140 ] 18 78 M16 4 18 100
I
40 150 18 I 8 8 3 M16 4 18 70 5
50
65
165
185
20
22
1P2
122
3
3
I
I
M16
M16
1 4
8 I ;: 125
145
84
101
1 6
6
80
100
200
235
24
24
138
162
3
3
M16
M20 1 8
8
18
22
120
143 i 6
125
150
270
300
26
28
188
218
3
3
I
M24
M24 I
I .
26
26 1 220
250
171
202 I 8
A.% NOTE. Alternative neck form, show dotted, t o have a maximum draft angle of 12'.
52
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*4504: P A R T m L b7 l b 2 4 b b 7 0278033 3 =
BS 4504 : 1969
TABLE 25/13. MALLEABLE CAST IRON SCREWED BOSS FLANCIES

Nominid pressum 2S bar (1 bar 10' N/m? -
All dlmcniloni ira In milllmircs (oxcapt tho inch nomlail Jrs column). Screwed to 8s 11, ' Pl# thraadr '.
er 1:6*25 on dldmetcr
Nominal atze 0.r I

PI
-- b No. 4
6 10.2 75 14 4 11 50 20
8 13.5 80 14 4 11 55 25
10 i7.a 90 16 4 14 60 30
15 21.3 95 16 4 14 65 35
20 26.9 105 18 Ml2 4 14 75 45
25 33.7 115 18 2.8 Ml2 4 14 a5 52

32 424 140 18 30 M16 4 18 100 60
40 48.3 150 18 33 M16 4 18 110 70
50 60.3 165 20 34 M 16 4 18 125 85
65 764 185 22 38 M16 8 18 145 105
80 88.9 200 24 40 M 16 8 18 160 118
100 1144 2.35 24 44 M20 8 . 2 2 190 145
125 139-7 270 26 48 M24 8 26 220 170
150 165.1 300 28 52 Ma4 8 26 a50 200
53
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BS 4504 : 196'1
TABLE 40/1. INTEGRAL STEEL FLANGES

Nominal pressurc 40 bar (i bar = 10' N/m')
Nom. Drilling
612C
r
10 2 1 M12 1 4 14 60 30 4
15 2 14 65 37 4
20 2 M 12 14 75 44 5
25
32
2
2
M 12
M16 I
I
4
4
14
18
85
100
53
60
5
5
40 3 M 16 4 18 110 68 5
50 3 M16 4 18 125 80 5
65 185 ; 22 i22 3 M16 a 18 145 99 6
80 200 24 138 3 M16 a 18 160 116 6
100 235 I 24 162 3 M20 8 22 190 136 6
I a a
125
150
175
200
250
270
300
350
375
450
Ii 26
28
32
34
38
188
218
260
285
345
3
3
3
3
3
M 24
M24
M27
M27
M30
ia
12
12
a
26
26
30
30
33
220
250
295
320
305
.165
192
223
252
308
8
10
10
10
300 515 42 I 410 4 M30 16 33 450 364 12
350 4 M33 16 36 510 420 12
A p:: 4
'4
5
M36
M39
M45
16
20
20
39
42
48
585
670
795
476
578
690
12
15
15
ri36 AO 610 5a6 IA
700 995 64 a40 5 M45 24 48 900 796 18
800 M 52 24 56 1050 908 18
900 1250 i 76 M52 20 56 1 x40 1014 18
loo0 1360 80 1180 5 M 52 28 56
1 200 1575 f
'
88 I 1380 I
i
5 M56 31 62
1250
1460
1120
1332
20
20
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
1 400 1795 '

I
I
98
i 5 M56 36 62 1680 1548 20
1600 2025 108 M64 40 70 1900 1763 20
A NOTE. Alternative neck form, sham dotted,'to have a maximum draft ongle of .'21
55

~
BSI B S * 4 5 0 4 : P A R T * 1 69 1624669 0278035 7
BS 4504 : 1969
TABLE 40/ZSTEEL WELDING NECK FLANGES

Nominal pressure 40 bar (1 bar = 10' N/m')
1 For weld preparation see

8.S.2633 and 8.S.2971 or
8.S. 1821 and B.S.2640
Nom.
P h
0.d.
Fînnge 1 ~atsedface Doltlng Drilling Neck
size dl hi
-- da I
- No. I--d: I k
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
10 17.2 35 40 2 M12 14 60 28 6 . 4
15 21.3 38 45 2 M12 14 65 32 6 4
20 26.9 40 58 a k112 14 75 40 6 1 4
25 33.7 40 68 2 M12 14 85 46 6 ; 4
32 42.4 42 78 2 M16 18 100 55 6 1 6
40 48.3 150 18 45 88 3 M16 18 110 64 7 : 6
50 60.3 165 20 48 102 3 F.416 18 125 75 8 . 6
65 76-1 185 22 52 122 3 M16 145 90 10: 5
80 88*9 200 24 58 138 3 M16 160 105 12 j 8
100 114-3 235 24 65 162 3 M20 190 134 12 : 8
I !
125 139.7 270 26 6û 188 3 M24 8 26 220 162 12 8
150 168-3 300 28 75 218 3 M24 8 26 250 192 12 10
175 193.7 350 32 82 260 3 M27 12 30 295 218 15 10
200 219.1 375 34 88 285 3 M27 12 30 320 244 16 : 10
250 273 450 38 105 345 3 hI30 12 3 3 3 8 5 306 18 12
300 323.9 515 42 115 410 4 M30 16 33 450 362 18 12

350 355.6 580 46 125 465 4 M33 16 36 510 4oa 20 12
406.4 660 50 135 535 4 M36 16 39 585 462 20 12
508 755 52 140 615 4 M39 20 , 42 670 562 20 12
w7-A 6B5 50 135 560 it. M 36 - 20 I 500 20 IL
56

BSI B S * 4 5 0 4 : P A R T * 1 69 m 1624669 0278036 9 m
BS 4504 : 1969
TABLE 4/3. STEEL PLATB FLANGES FOR WELDING
Nominal pressure 40 bar (1 bar = 10' N)m3
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Nom. Drillhg
size
f I ~~ ~
11
10 1712 90 16 40 2 M12 4 14 60
15 22.3 95 16 45 2 M12 4 14 65
20 26.9 105 18 58 2 M12 4 14 75
25 33.7 115 18 68 2 M12 4 14 85
32 42.4 140 18 78 2 M16 4 18 100
40 48.3 150 2 0 ' 88 3 M16 4 18 110
50 60.3 ' 165 20 102 3 M 16 4 18 125
65 7611 185 22 122 3 M16 8 18 145
80 88.9 200 24 138 3 M16 8 18 160
100 114.3 235 26 162 3 M20 8 22 190
125 139.7 270 3 M24 8 26 220
150 16813 300 30 218 3 M24 8 26 250
175 193-7 350 32 260 3 M27 12 30 295
200 219.1 375 34 285 3 M27 12 30 320
250 273 450 42 345 M30 12 33 365
300 323.9 515 16 33 450
350 355.6 580 16 36 510
fA P E 406.4
508
660
755
16
20
39
42
585
670
WO (t57'A b 83- AO
--
39 610

BSI. BSa4504: P A R T * L 69 -- O
1624663 0278037 =
BS 4504 :1969
All dlmonsionr
TABLE EL SCRkWED BOSS FLANGES
Nominal p'css&'25 biV and 40 bar (1 bar 10' N/m? -
4
I.' k
0 c
- I Rilsedîaee
- Bolt Inp Boss
4
I
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
-
b
-
f
.~
No. I, k
14 2 M10 4 11 50 20
14 2 M 10 4 11 55 25
16 2 Ml2 4 14 60 30
16 2 Ml2 4 14 65 35
18 2 M12 4 14 75 45
18 2 Ml2 4 14 85 52
18 2 M16 4 18 100 60
18 3 M 16 4 18 110 70
20 3 M16 4 18 125 85
22 3 M 16 8 18 145 105
3 80 88.9 200 24 40 138 3 M16 8 18 160 118
4 100 114.3 235 24 44 162 3 M20 8 22 190 145
5 125 139.7 270 26 48 188 3 M24 8 26 220 170
6 150 365.1 300 28 52 218 3 M24 8 26 250 200
- I
58

BSI B S * 4 5 0 4 : PART*<L b î 1624669 0278038 2 =
ES 4504 : 1969
.
TABLE 4015. STEEL SLlP-ON BOSS FLANGÈS FOR WELDING
Nominal pressure 40 bar (1 bar 10' N/m9 '
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
I
iter
Nom.
R a W face
size Bolting
-- D b i f
6 10.2 75 14 20 32 2 M10 11 50 20
8 13.5 80 14 20 38 2 M10 11 55 25
10 17.2 90 16 22 40 2 M12 14 60 Y)
15 21.3 95 16 22 45 2 M12 14 65 35
20 26.9 105 18 26 58 2 M12 14 75 45
25 33-7 115 18 28 68 2' M12 14 85 52

32 42.4 140 18 30 78 2 hí 16 18 100 60
40 48.3 150 18 32 88 3 M16 18 110 70
50 60.3 165 20 34 102 3 M16 18 125 85
65 76.1 185 22 38 122 3 M16 18 145 105
80 88-9 200 24 40 138 3 M16 8 18 160 118

100 114.3 235 24 44 162 3 M20 8 22 190 145
125 139*7 270 26 48 188 3 M24 8 26 220 170
150 168.3 300 28 52 218 3 M24 8 26 250 200
200 219.1 375 32 52 285 3 M27 12 30 320 260
250 273 450 40 60 345 3 M30 12 33 385 320

300 323.9 515 48 67 410 4 M30 16 33 450 380
--
59

BSI BS*4504: PART*& 6 9 W 3b24bb9 0 2 7 8 0 3 9 4 =
BS 4504 : 1969
TABLE 'STEELPLATE BLANK FLANGES
Nomlrial pressure 40 bar (1 bar = IO5 N/m*)
.
NOTE The two types of flanges shown am alternatives at the option of the manufacturer.
. .
Form B Form C
b
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
10 M12 60
15 M12 65
20 M12 75
25 M 12 85
32 140 18 M16 4 18 100
40 150 18 -
- M16 4 18
18
110
125
50 165 20 M 16 * 4
65 185 22 . 55 M 16 8 18 145
80 200 24 70 M 16 8 18 160
100 235 24 90 M20 8 22 190.
125 270 26 115 M24 8 26 220

150 300 28 140 M24 ' 8 26 250
175 350 32 165 M27 12 30 295
200 375 34 190 M27 12 30 320
250 450 38 237 M30 12 33 385
300 515 42 285 M30 16 33 450

350 580 46 332 M33 16 36 510
n I 660
755
6SS
50
56
54.
380
475
-
+A 5%
M36
M39
m36
16
20
020
39
42
39
585.
670
6I O
60

~
BSI B S * 4 5 0 4 : PART*l 69 Lb24669 0 2 7 8 U 4 0 O
BS 4504 :1969
TABLE 64/1. INTEGRAL STEEL =ANGES
Nominal pressure 64 bar (1 bar = 10' N/rn')
NOTE.For nomlnd iIzcs 10 m m to 40 mm use Table 160/1.

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
I I .-
L I-
4 -il I I
I k
I
Nom. Flange Drlulng Neck
n
h
b No. 4 h
50 102 3 M20 4 22 135 gr) 5

65 122 3 M20 a n 360 105 5
80 138 3 M20 8 22 170 122 5
100 30 162 3 M24 8 26 200 146 5
125 34 188 3 M27 8 30 240
150 345 36 218 8 33 280 6

175 375 40 260 3 M30 12 33 310 8
200 515 42 285 3 M33 12 36 345 264 8
250
300
470
530
46
52
345
410
3
4
M33
M33
12
16
36
36
400
460
320
378
1
I 8
10
350 600 56 465 4 M36 16 39 525 434 10
400 670 60 535 4 M39 16 42 585 490 12
500 800 68 615 4 M45 20 4a 705 602 12
600 930 76 735 4 M 52 20 56 820 714 15
700 1045 84 840 4 M52 24 56 935 826 15
800 1165 92 960 4 M56 24 62 1050 938 18

900 1285 98 1070 4 M56 28 62 1170 1048 18
loo0 1415 108 1180 4 M64 28 70 1 290 1 162 18
1200 1665 126 1380 4 M72 32 70 1 530 1390 18
c-. 2
NOTE Alternative neck form, shown dotted, to have a maximum draft angle of 12'
62

Nominal pressure 64 bar (1 bar = 10' N/mp
NOTE For nomInal shes 10 mm to 40 mm uso Table lW/2.
I
For weld preparation sec
B.S.2633 and 0.S.2971or
8.S. 1821 and B.S.2640
f 1 ,(as appropriate
f
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
I L k
n
I
Nom. ',!a: -
FlangeI Rnlsedface Bolthg
Drluiog Neck
size ~
c
--,
dl D
-
b
-
hl
- 4
- f
-
No.
-
4 4
-
c
50 60.3 180 26 62 102 3 M20 4 22 135 82 10 6

65 76-1 205 26 68 122 3 M20 8 22 160 98 12 6
80 88.9 215 28 72 138 3 M20 8 22 170 112 12 8
100 1144 250 30 78 162 3 M24 8 26 200 138 12 8
125 139.7 295 34 88 188 3 M27 8 30 240 168 12 8
150 168.3 345 36 95 218 3 Ai30 8 33 280 202 12 10

175 193.7 375 40 105 260 3 M30 12 33 310 228 16 10
200 219-1 415 42 110 285 3 M33 12 36 345 256 16 10
250 273 470 46 125 345 3 M 33 12 36 400 316 18 12
300 323.9 530 52 140 410 4 M33 16 36 460 372 18 12
350 355.6 600 56 150 465 4 M36 16 39 525 420 20 12

400 406.4 670 60 160 535 4 M39 16 42 585 475 20 12
--
.
.
63

BsI B S * 4 5 0 4 : PART*L 69 Lb24669 0 2 7 8 0 4 2 4 rn
BS 4504 :1969
TABLE 64;3. STEEL PLAm FLANGES FOR WELDING
Nominal pmm 64 bar (1 bar 10' N/m3 -
N O ï Z For nodoal rtes 10 m m to 40 mm uso Table 100jJ.
I D
k
I
'ofr i
;
Fiange 1 Raisedfao
Bolting
milling
26
26
30
102
d.
122
138
I,
i
3
3
M20
M20
M20
4
8
8
22
22
22
~
k
135
160
170
-
114.3 250 32 162 I 3 M24 8 26 200

139-7 295 34 188 3 M27 240
168.3 345 36 218 3 M30 280

393.7 375 40 260 3 M30 310
219.1 415 46 285 3 M33 345
273 470 54 345 3 M33 400
323.9 530 62 410 4 M33 460
350 72 465 4 M36 525

400 78 535 4 M39 585
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

ES1 B S * 4 5 0 4 : PART*1 69 = 1624669 0278043 b
BS 4504 ; 1969

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

Ali dimensions m fn miilirnctrcs (except tho Inch nominal atz0 column). Screwed to BS 21, ' Pipe threads *.
NOTE. For nominal sizes % in to 1% in uso Tabla 10014.
diameter
17
Flange Raked face Drilling Boss
-- - Bolting
D b h f No.
- - - -
da
- -
2 50 60.3 180 26 36 102 3 M2û 4
2% 65 76-1 205 26 40 122 3 M20 8
3 80 88.9 215 28 44 138 3 M2û 8 22 3
4 100 114.3 250 30 52 162 3 M24 8
5 125 139.7 295 34 56 188 3 M27 8 30 185
I
6 150 165.1
I 3 3 I 2ao I 215

BSI B S * 4 5 0 4 : PART*KL bî m' L b 2 4 6 6 9 0278044 8
BS 4504 : 1969
TABLE lOO/l. INTEGRAL STEEL FLANGES

Nominal pressure 100 bar (1 bar = 10' N/m')
NOTE. For nominal s h r 10 mm to 100 mm uso Table 160/1.
I I l k
Y
d I I I
I It' d4
'U I
Nom.
iise
Flange Raked face
-I Bolting
r I No.
125 315 40 188 8. 6
150 355 44 218 12 6
175 385 48 260 3 M30 12 8
200 430 52 285 3 M33 12 36 360 278 8
250 505 60 345 3 M36 12 39 430 340 8
!
300 585 68 410 4 M39 16 10
350 655 74 465 4 M45 16 10
400 715 78 535 4 M45 16 12
500 870 94 615 4 M52 20 15
600 990 104 735 4 M56 20 15
700 1145 120 840 24 70 i 1020 860 i 18

i
A NOTE. Alternative neck form, shown dotted, t o have a maximum draft angle of 12'
66
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

B S I BSW4504: PART*L 69 Lb24669 0 2 7 8 0 4 5 T
BS 4504 : 1969
TABLE lûû/2.. STEEL WELDING NECK FLANGES

Nominal piessure 100 bar (I bar = 10' N/rn*)

B.S. 2633 and B.S.2971 or
B.S. 1821 and B.S.2640
Nom. Pipe
0.d.
Flange
- Bolting
Drilling I Neck
-
size -I
dt D b
-- -
No. 4 I & I dr ha
x
--
10 17.2 100 20 45 40 2 M 12 4 14 70 32 6
15 21.3 105 20 45 45 2 M 12 4 14 75 34 6
20 26.9 130 22 58 58 2 M16 4 18 90 42 8
25 33.7 140 24 58 68 2 M16 4 18 100 52 8
32 42.4 155 24 60 78 2 M 20 4 22 110 62 8
40 48-3 170 26 62 M20 4 22 125 70 10

50 60.3 195 28 68 M24 4 26 145 90 10
65 76-1 220 30 76 M24 8 26 170 108 12
ao 88.9 230 32 78 M24 8 26 12
100 114.3 265 36 90 M 27 8 30 12
125 139.7 315 40. 105 M30 o 33 250 180 12 8
1
150
175
200
16803
19307
219-1
1i 505355
385 I
44
48
115
127
130
M30
M 30
M33
12
12
12
33
33
36
290
320
360
210
215
278
12
16
16
- 10
10
10
250 273 , 157 M36 12 39 430 340 18 12
300 323.9 585 Ge 170 M 39 16 42 500 400 18 12
350 355.6 i ,655 ' 74 189 M45 16 48 560 460 20 12
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
67

BSI B S * 4 5 0 4 : PART*:L 6 9 W L b 2 4 b b î 0 2 7 8 0 4 b 1
BS 4504 : 1969
TABLE l00/3. STEEL PLATB FLANGES FOR WELDING

Nominal pressure 100 bar (1 bar = 10' N/m?
Nom. Drilling
Stze
b I 4' f I No. h
10 17.2 100 20 40 2 M12 4 14 70

15 21.3 105 20- 45 2 M12 4 14 75
20 26.9 130 22 58 2 M16 4 18 90
25 33.7 140 24 68 2 M16 4 18 100
32 42.4 . 155 24 78 2 M20 4 22 110
40 48.3 170 26 88 3 M20 4 22 125

50 60.3 195 28 102 3 M24 4 26 145
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
65 76.1 220 30 122 3 M24 8 26 170

80 88*9 230 ' 34 138 3 M24 8 26 180
100 114.3 265 36 162 3 M27 8 30 210
125 139.7 315 42 188 3 M30 8 33 250

150 168.3 355 48 218 3 M30 12 33 290
175 193.7 385 54 260 3 M30 12 33 320
200 219-1 430 60 2-05 3 M33 12 36 360
250 273 505 72 345 3 M36 12 39 430
300 323.9 585 84 410 4 M39 16 42 500

350 355.6 655 95 465 4 M45 16 48 560
400 406-4 715 106 535 4 M45 16 48 620
500 508 870 128 615 4 M52 20 56 760
68

BSI BS*4504: P A R T * 1 b î 1624bbî 0278047 3 m
BS 4504 : 1969

All dimensions a n in millimetrcs (except Inch nominal slze column). Screwed to BS 21, Pipe threa' '.
k dS
For seal welding

diameter
Boss
___- - Ralsed face
in b I No. k
94 10 17.2 100 20 28 40 2 M12 4 14 70 2

'/a 15 21.3 105 20 28 45 2 M12 4 14 75 2
w 20 26.9 130 22 30 58 2 M16 4 18 90
100
2
3
1 25 35.7 140 24 32 68 2 M16 4 18
1% 32 42.4 155 24 32 78 2 M20 4 22 110 68 3
1% 40 484 170 26 34 88 3 M20 4 22 125 80 3

2 50 60.3 195 28 36 102 3 M24 4 26 145 95 3
2% 30 40 122 3 ' M24 8 26 170 3
3 32 44 138 3 M24 8 26 180 3
4
5 125 139.7 I 315

36
40
52
56
162
188
3
3
M27
M30
8
8
30
33
210
250
3
3
6 150
I
165.1
I
355 44
- - --
60 218 3 M30 12
-
33
290 i 225 I 7
3
-
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
69

BSI BS*450q: P A R T * 1 69 1624669 0278048 5 rn
BS 4504 :1969
. TABLE 160/i INTEGRAL STEEL FLANCiES
N o d d pr~ssura160 bar (1 bar = 10' N/m$
Nom.
rlze
D
Nango
I '
Raiseà face
f I
I . biting
No.
Drillhg
k 48
Neck
10 100 20 40 2 M12 4 14 70 40
15 105 20 45 2 M12 4 14 75 45
20 130 22 58 2 M16 4 18 90 50
25 140 24 68 2 M16 4 18 100 61
32 155 26 78 2 M20 4 .. 22 110 68
40 170 28 a8 3 M20 4 22 125 82
50 195 30 102 3 M24 4. 26 145 96
65 220 34 122 3 M24 8 26 170 118
80 230 36 138 3 M24 8 26 180 128
100 265 40 162 3 M27 8 30 210 150
125 315 44 188 3 M30 8 33 250 184
150 355 50 218 3 M30 12 33 290 224
175 390 54 260 3 M33 12 36 320 250
200 430 60 285 3 M33 12 36 360 288
250 515 68 345 3 M 39 12 42 430 346
300 585 78 410 4 M 39 16 42 500 414 10
/2\
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
NOTB. Altemintive riock form,' d oI t~t e d , have ' a 'm&muxi'h~aft of 1 Z"

S ~ O W
. .. . ' $0
70

BSI BS*4504: P A R T * l 69 M 1624667 0278049 7
BS 4504 : 1969
TABLE 16% STEEL WELDIN0 NECK W û E S

Nomlnal pressura 160 bar (1 bar = IO' N/m?
I
For weld DtcDaration see
B.S 2633'and 8.C.2971 or
B.S.1821 and BS2640
I I + "4
I I
Nom. PlPo
0.d. --
Fiange Drllltnp I Neck
size
10
15
---
dl
17.2
2113
DI'
100
105
20
20
45
45
40
45
2
2
M12
M12
NOU
4
4
14
14
70
75
~~
32
34
-
x -
rha
6
6
4
4
20 26.9 130 22 58 58 2 M 16 4 18 90 42 8 4
25 33.7 140 24 58 68 2 M16 4 18 100 52 8 4
32 42.4 155 26 60 78 2 M20 4 22 110 55 8 6
40 48.3 170 28 64 88 3 M20 4 22 125 70 10 6
50 60.3 195 30 75 102 3 M24 4 26 145 90 10 6
65 '76.1 220 34 82 122 3 M24 8 26 170 108 12 6
80 88 b9 230 36 86 138 3 M24 8 26 180 120 12 8
100 11403 265 40 100 162 3 M27 8 30 210 150 12 8
125 139-7. 315 44 115 188 3 M30 8 33 250 180 14 8
150 168.3 355 50 128 218 3 M30 12 33 290 210 14 10
175 193.7 390 54 138 260 3 M33 12 36 320 245 16 10
200 219.1 430 60 140 285 3 M33 12 36 .360 278 16 10
250 273 515 68 155 345 h139 12 42 430 340 18 12
300 323-9 585 78 175 410 M 39 16 42 I 500 I 400 18 12
- --
71
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

B S I BS*4504: PART*L 67. Lb24667 0278050 3
I b
m
BS 4504 :1969
Nom. PI
dm ?!.o
4 D I ' 4 I f k
10 1742 100 1 2 2 40 2 M12 4 14 70

15 21.3 105 24 45 2 M12 4 14 75
20 26.9 130 26 58 a M16 4 18 90
85 33.9 1W 26 6a i ht16 4 18 100
32 424 155 28 78 a M20 4 22 110
40 483 170 34 83 3 M2û 4 22 125

50 60.3 1% 34 10a 3 MaQ 4 26 145
65 76.1 220 36 122 3 M24 8 26 170
80 88.9 230 40 138 3 M24 8 26 180
100 114.3 265 44 162 3 M27 8 30 210
l25 139.7 315 54 188 3 M30 8 33 250

150 1683 355 6a 218 3 M30 la 33 290
175 19517 390 68 260 3 M33 i2 36 520
200 219.1 430 76 285 3 M33 12 36 siw
250 273 515 90 345 3 M39 12 42 430
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
.300 ,723.9 585 lo6 410 4 M39 16 42 500

--
7?

BSI BS%4504: P A R T * 3 6 9 3b24bb9 0278053 5 m
- . BS 4504 : 1969
.~
T ..
.. _ -...
.
.
Neck
Nom. Bolting
size
No. c
.-
10 125 24 40 2 M16 4 18 85 46 1
15 130 26 45 2 M16 4 18 90 52 4
20 135 28 58 2 M16 4 18 95 57 4
25 150 28 68 2 M20 4 22 105 63 4
32 165 32 78 2 M20 4 22 120 78 4
40 185 34 88 3 M24 4 26 135 90 4

50 2 0 38 102 3 M24 8 26 150 102 5
65 230 42 122 3 M24 8 26 180 125 5
80 255 46 138 3 M27 8 30 200 142 6
100 m 54 162 3 M30 8 33 235 168 6
125 340 60 188 3 M30 12 33 275 207 6

150 390 68 218 3 M33 12 36 320 246 8
175 430 74 260 3 M36 12 39 355 275 8
200 485 82 285 3 M39 12 42 400 314 8
250 585 100 345 3 M45 16 48 490 394 10
300 690 120 410 4 M48 16 52 590 480 10
4 NOTE. Alternative neck form, shorn dotted, t o have a

maximum draft angle of 12 ,
73
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*:YSO:Y: PART*I 69 = Lb2:Ybhî 0 2 7 8 0 5 2 7
~
r -
EIS 4504 :1969 .-
ELWELDÍNG
, - < - ..- NECK FLA
'ih6ar (1 bar ='IO1 N/m9
. .
'm.- , _.. .
~. . ~
fi..'.
. . I. -: . .... . _.. . .
. .
.~
: ...
-
N6m.
rLe
PI
0.g: - -
Rilscd fica
- Driiihg
-
h
dl D
--
4 f
-
No.
-4 h 48 r
-
15 21.3 130 26 60 45 2 MI6 4 18 90 48 6 4
20 26.9 135 28 65 58 2 M16 4 18 95 55 6 4
25 33*7 150 28 65 68 2 M20 4 22 105 60 8 4
32 42.4 165 32 75 78 2 M20 4 22 120 74 8 6
40 48.3 185 34 80 88 3 M24 4 26 135 84 10 6
50 60.3 200 38 85 102 3 M24 8 26 150 95 10 6

65 76.1 230 42 95 ' 122 3 M24 8 26 180 124 12 6
80 1016 255' 46 102 138 3 M27 8 30 m 136 12 8
100 127 300 54 120 162 3 M30 8 33 235 164 14 8
125 152.4 340 60 140 188 3 M30 12 33 275 200 16 8
150 171.8 390 68 160 218 3 M3.3 12 36 320 240 18 10

175 219.1 430 74 170 260 3 M36 12 39 355 270 22 10
200 244.5 485 82 190 285 3 M39 12 42 400 305 25 10
250 298 a5 585 100 215 345 3 M45 16 48 490 3 8 5 3 0 12
---- - -
14
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S U 4 5 0 4 : PART*l 69 l b 2 4 b b 9 0278053 9
BS 4504 : 1969
TABLE32011. I~TEGRAL=EL
Nominai pressure 320 bar (1 bar
. -
- FLANGES
10' N/m3
Nom. I Neck
size Bolthg .
0 b 4 f Na c
10 125 24 40 2 M16 4 18 85 46 4
15 130 26 45 2 M16 4 18 90 52 4
20 150 30 58 2 M20 4 22 105 62 4
25 160 34 68 2 M20 4 22 115 72 4
32 180 36 78 2 M24 4 26 130 a2 5
40 195 38 88 3 M24 4 26 145 96 5

50 210 42 102 3 M24 8 26 160 110 5
65 255 51 122 3 M27 8 30 200 137 6
80 275 55 138 3 M27 8 30 220 160 6
100 335 65 162 3 M33 8 36 265 190 8
125 380 75 188 3 M33 12 36 310 235 8

150 425 84 218 3 M36 12 39 350 24x 10
175 485 95 260 3 M39 12 42 400 310 10
200 525 103 285 3 M39 16 42 440 350 10
250 640 125 345 3 M48 16 52 540 432 10
A . ..NOTE.Alternatlve:neck form, shown d o t t e d , t o have a m a x i m draft angle of 12'
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*L 69 M Lb24669 0278054 O I
ns 4504 :1969
. TABLE3 2 0 ~STEEL WELDING NECK FLANGES
NomInal p m - 320 bar (1 bar = 10' N/m?
I . For weld DrcDaration see

0.S2633'and B.S.2971or
rw
B.S.1821 and B.S.2640
ofappropriate
-- m-I-Neck -
No.
- -
41
-
ha
%
.
r
- I d8
10 17.2 125 24 58 40 2 M16 4 18 85 44 6 4

15 21.3 130 26 60 45 2 M16 4 18 90 48 6 4
20 26.9 150 30 72 58 2 M20 4 22 105 58 6 4
25 33.7 160 34 78 68 2 M20 4 22 115 68 8 4
32 42.4 180 36 84 78 2 M24 4 26 130 78 8 6
40 48-3 195 38 88 88 3 M24 4 26 145 92 10

50 63'5 210 42 100 102 3 M24 8 26 160 106 10
65 88.9 255 51 120 122 3 M27 8 30 200 138 12
80 101.6 275 55 130 138 3 M27 8 30 220 156 14
100 139.7 335 65 145 162 3 M33 8 36 265 186 16
125 168.3 380 75 175 188 3 M33 12 36 310 230 20 8
150 193.7 425 84 195 218 3 M36 12 39 350 265 25 10
175 219.1 485 95 215 260 3 M39 12 42 400 308 28 10
200 244.5 525 103 235 285 3 M39 16 42 440 345 30 10
250 323*8 640 125 300 345 3 M48 16 52 540 428 40 12
-
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*L 69 = Lb24bbî 0278055 2
TABLE 4Uû/i. INTEGRAL STEEL FIANGES .

Nominal pressun 400 bar (1 bat 10' Nlrn')
p.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
AI olirrrd
.\lmrh, 1371
Sl7Æ
1 Rakeitace I Neck
M 16
M20
20 I 160 M20
25 f 180 3 8 ' 6 8 1 2 M24
32 : 205 , 44 78 2 I MZ7
40 220i 4 8 ! 8 8 [ 3 M27 165

5 0 1 2 3 5 52 102 I 3 M27 180
6 5 ' 2 9 0 . 64 , 1 2 2 1 3 M30 8 33 225
80 "335 68 138 ! 3 M30 a 33 240
100 ~ 370 80 162 i 3 M36 8 39 295
I
125 . 415 92 188 . 3 M36 12 39 340

150 475 ! 105 218 ' 3 M39 12 42 390
175 I 545 r 120 2 6 0 1 3 M45 12 48 450
200 130 : M45 16 48 490
I I
/h\NOTE. . .._.-.
Álternaiivc neck form, shown dotted, to have ----.---.draft angle
a maximum . of 12 O,.
77

BSI B S * 4 5 0 4 : P A R T * L 69 L624bbî 0 2 7 8 0 5 6 4
Lsi 4504 :1969

TABLE 4ûûK STEEL WELDING NECK FLANGES
Nominal prrssun 400 bar (1 bar l(r Nlm3
I Far weld preparation see

0.S 2633 and 0.S.2971 or
B.S. 1821 and 88.2640
I g as appropriate
r
8 f
i L k I
A i alrrnd
Ahlatch. 19II
NOUI.
r h
10
15 2 M20
20 3 M20
25 2 M24
32
40
48.3
60.3
1 205
220
I 4 4
48
Ilo1
110
78
88
2
3
M27
M27 165 106 ; 12 G
50 76.1 1 235 52 120 102 3 M27 120 15 1 6
I
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
65 101.6 290 64 135 122 3 M30 158 18 I>

80 114.3 305 68 150 138 3 M30 174 20 : 8
100 139.7 1 370 80 175 162 3 M36 216 25 8
125 193.7
I
I 415 92 200 188
i M36 340 i 258 : 30 ' 8
I
150
200
219.1 475 105 225
280
218
285
- I
48 ; 490 i 302
388
i
35
40
'
!
10
10

E S 1 BS*4504: PART*KL b 7 H L b 2 4 b b 7 0278057 b
Amendment Slip No. i, published 17 March, 1971

to BS 4504: 1969 *
Flanges and bolting for pipes, valves and fittings
Metric series
Revised text
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Page 2. In the list of reference standards delete the last item and substitute
'BS 4622. Grey cast iron pipes and fittings (Metric dimensions).'
Contents. In the title of Table 6/8 delete 'blank figures' and substitute 'blank
flanges'.
Foreword, In thc first line of the final paragraph delete 'and is published as an
interim measure'.
Add a full stop after 'European practice'.
At the bottom of the Foreword delete the existing Note and substitute the
following:
'NOTE I. Pressures in this standard are given in bar (gauge) 1 bar=lO N'/ma.
NOTE 2. All dimensions throughout this standard are in millimetres unless otherwise stated.'
Claw 4.3.1. Outside diameter (D). Delete 'mm' in all cases.
Clause 4.3.2.1. Delete 'mm' in all cases.
Claw 4.3.2.2. Delete 'mrn' in all cases.
Page 7. In the first line of the second paragraph of the footnote under column 2
. .'
delete 'see BS , and substitute 'see BS 4622'.
In the second and third lines of this paragraph delete '(In course of
preparation)'.
Claw 4.3.2.3. Dzlete the whole of this clause.
Ciause 4.3.3. Delete 'mm' in all cases.
Claw 5.1. Matertiìs and threads. At the end of the first paragraph add the
following:
'Free cutting steel for bolts, stud bolts and nuts shall only be permitted when
specified by the purchaser, and its use shall be restricted to the temperature
range-lo "C to 200 "C for nominal pressures up to and including 16 bar.'
Delete the whole of the fourth paragraph.

~
E S 1 BS*4504: PART*:L bï L b 2 4 b b î O278058 8
TABLE, A i Page io.

In column 3 under the heading 'Steel forgings'
Line Delete Substiiui?
1 BS 1 W - 5 0 3 LT 100 BS 1sWscM LT 100
2 BS 1503-161A LT 50 BS 1503-224-28A LT 50-
3 BS lbüJ-161A BS 1m-161G rade %A
a 070 M20t 070 M20t
BS 1503-161 G rade 26A
BS 1503-161A
6 BS 1503-503 LT 100 RS 1503-503 LT 100 -.
7 161A LT 50 BS . .
1503 224 28A LT 56
1503-161A BS 1563-161 Grade 26A
O M20t OïO M20t
lo BS 1503-161A BS 1503-161 Grade 26A
BS 1503-503 LT 100 BS EXB-503 LT 100
12 LT 50 - -
BS 150322428A LT 50
1 3 B S T 5 m - 1 6 1 A BS 1503-161 Grade 26A
14 070 M20t 070 M2Ot
5 BS 1503-161A BS 1503-161 G rade 26A -
16 BS 1503-161 B BS 1503-161 Grade 28A -
LT 100 BS 1303-503 LT 100
8 BS 1503-161A LT 50 BS 1503-224-28A LT 50 -
+?O%h,
9 6 A
BS 1503-161 Grade 28A--
BS 1503-161
070 M2ût Grade 26A
zz BS 1333-%B-LT100 BS 1503-503 LT 100

BS 1403-161A LT 50 BS 1503-234-28A LT 50
24 1 5 ú 3 Z - t B S 7 5 0 3 - 1 6 r G r a d e %A
26
070 M20
BS 1503- BS 1503-161 Grade 28A
-
2 7 7 K T 5 @ 3 - 1 6 1 B 1
6-
3
0
5
1 Grade B A -
29 BS l
1503-2408
~ S ~ 2
mmA----z7 l __ A
30 BS 1503-620 BS 1503-621
Si BS 1503-620 BS 1503-621
32 BS 1503-503 LT 100 BS 150.3-503 LT 100
7 BS 1503-161A LT 50 BS 1503-224-28A L T ~ O -
34- BS 1503-161A BS 1503-161 Grade %A
35-70 M2û 070 M2ût
r F d 6 1 B BS 1503-161 Grade 2ûA
3'1 03-161B BS 503-1 Grade 2ûA-
BS 1503-SWB 4 X E +
39 BS 1503-240B BS 1503-271A
625 BS 1 5 0 3 - 6 2 1 -
7 B S 1503-620 BS 1503-621
In column 5, lines 20,25 and 35, delete '6.6' and substitute '4.6'.
In column 6, lines 20, 25 and 35, delete '6' and substitute '4'.
In columns 5 and 6, line 31, delete 'See Note 5' and substitute 'See Note 4'.
TABLE Al, Pages 10,11,12
In the column headings for 'Nominal pressure' and 'Design pressure' on each of
these pages delete 'bars' and substitute 'bar'.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
TABLE Ai, Page i1

In column IO, line IO, under '-10 to 120' deletc '110' and substitute '100'.
In column 2 delete ali references to steel plate materials for NP wl.
in column 3 under 'Steel forgings'
Line Delete Substitute

1 HS 1503-503 LT 100 BS 15a3-5¢ I
2
3
BS 1505161A LT 50
BS 1503-16149
BS 1503-22
BS 1503-lf
&YE 50
rade 26A
--
4 BS 1503-161B Bs 1503-16 e 28A
5 BSm61B BS 1503-16 Grade 28A
6 BS 1503-240B BS 1503-27
7 BS 1503-2408 BS 1503-27
BS 1503-620 a
A
19 1
n I
I
r--- I
23 I
36 1
A
n7
3s 1503-622 BS 1503-622
3s 1503-503 LT 100 BS 1503-503 LT 100
3S 1503-161A LT 50 BS 1503-2&&4 LT 50
ES 1503-161A BS 1503-161 Grade '&A
ß S 1503-161B BS 1503-161 Grade 28A
ES 1503-161B BS 1503-161 Gr& 28A
3s 1503-2408 BS 1503-27lA
ES 1503-2408 BS 1503-27lA
BS 1503-620 BS 1503-621

BSI BS*:4504: PART*1 b ï = 1624669 0278060 b =
TABLE Al, Page 12

In column 2, delete all references to steel plate materials for NP 320 and NP400.
In column 3 under 'Steel forgings'
Line Delete Substitute

1 BS 1503-503 LL' 100 tis 1503-503 L I 100
2 BS 1503-161A LT 50 BS l!X3-2&2&4 LT 50
3 BS 1503-161A BS 1503-161 Gr 26A
BS 1503-1618 BS 1 5 0 5 1 A
5 BS 1503-1618 BS 1503-161 Gr& %A
BS 1503-2408 BS 1503-271A
7 BS 1503-2408 BS 1503-271A
__ BS 1503-620 BS 1503-621
ES 1503-621
6- BS
BS
1503-620
15û3-6a BS 1503-622
i--13 ; 2 K E BS%1503-16lA
E2EL 1 BS 1503-403LT 100
BS 1503-224-28ALT 50
BS 1503-161 Gr& 26A
14- BS 1505-1618 BS 1503-161 G r d e 28A
L B S W A 6 1B BS 1503-161 Q& 28A
Bs l u i
17 1503-1.408 BS 1503-271A
18 1503-620 ES 1503-621
19 BS 1503-+~0 BS 1503-621
20 BS 1503-622 BS 1503-622
TABLE A2, Page 13. In iolumn IS, line 14, under '220' delete '18' and substitute
']Y,
In the column headings for 'Nominal pressure' and 'Design pressure' delete
'bars' and substitute 'bar'.
TABLE B, Page 14. Under column 10/8 delete 'Use Table 16/7' and substitute
'Use Table i6/S1.
TABLE BI Page 15. Under column 25/8 delete 'Use Table 4Ö/7' and substitute
'Use Table 40/8'.
Under column 250/2, line 3, insert '*',
At the bottom of the Table add the following footnote:
'*Use Table 320/2'.
Ai the right hand side of ihc Table add a further column repeating the sizes
given in Column 1.
TABLE 2.5/2. Steel welding neck flanges. Under the heading delete 'Ail dimen-
sions are in milliinetres'.
TABLE 2,5/3. Steel plate flanges for weldfng. Under the heading delete 'All
dimensions are in millimetres'.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*4504: PART*1 69 m L b 2 4 6 6 9 0 2 7 8 0 6 1 8
TABLE 2.5111. Integral grey cast Iron Ranges. Under thc heading delete 'All
dimensions are in millimetrcs'.
TABLE 612. Steel welding neck flanges. Under the heading delete 'All dimensions
are in millimetres'. Add the following:
TABLE 6/3. Steel plate flanges for welding. Under the heading delete 'All dimen-
sions are in millimetres'. Add the following:
TABLE 6/5. Steel slipon boss íianges for wekiing. Under the heading delete 'All
In the drawing delete dimension 'K'*and substitute 'A'
TABLE 6/6. Steel locwe flanges for welded on lapped pipe ends. Under the heading
delete 'All dimensions are in millimetres'.
In column 2, line 17, delete '419' and substitute '406.4'.
450
1 I
Add the following:
dl
457-2 595
D I b m F
32 465
I8 (b'tlwI E i""'T 1
M20 22
-
k ?ye[!
550 520
TABLE 6/8. Steel plate blank flanges. Under the heading delete 'All dimensions
are in millimetres'. Add the following:
450 1 5DJ%4 I I ;4
TABLE 6/11, Integrai grey cast ir00 Ranges. Under the heading deletc 'All
;;b I 5;

Delete the whole of tho NOTE.
Add the following:
Nom.iIza I Dmy6 I Ri1ptdfice
dc I f
I E.ltIu8 I N a 1Drllllng
da I k I d~NeckI f
450 I595 I 30 15201 4 I M20 16 I 22 1550 1492 I 8 I

TABLE 6/12. Malleabk cast ir00 lategral Rpnges. Under the heading delete
'All dimensions aro in millimetres'.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*L 69 m Lb24669 0278062 T m
TABLE 6/13. Malleable casi iron screwed boss flanges. In column 4, line 11,
delete '180' and substitute '190'.
TABLE 10/2. Steel welding neck finges. Under the heading delete 'All dimensions
are in millimetres'.
TABLE 10/3, Steel plate flanges for weldlng. Under the heading delete 'All
TABLE 1015. Steel sllp-on boss Ranges for welding. Under the heading delete
'All dimensions are in millimetres'.
In column 12, line 5, delete '237' and substitute '247'.
In the drawing delete dimension 'K' and substitute 'k'.
TABLE 10/6. Steel loose fianges for welded on lapped pipe ends. Under the
heading delete 'All dimensions are in m¡llimetres'.
TABLE lo/& Steel plate blank flanges. Under the heading delete 'All dimensions
TABLE 10/11. Integral grey cast iron flanges. Under the heading delete 'All
rABLE lall. Integral steel flanges. Under the heading delete 'All dimensions
TABLE l6/2. Steel welding neck ílanges. Under the heading delete 'All dimensiow
TABLE 16/3. Steel plate fianges for weldlng. Under the heading delete 'All
TABLE 16/4. Steel screwed boss flanges. Delete the drawing and substitute the
following:
I
diameter
I k
I
6
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

- --
BSI BS*4504: P A R T 8 1 69 W 1624669 0278063 1 =
TABLE 16/5. Stecl slipon bms flanges for welding. Under the heading delete
All dimensions art: in millimetres'..
Delete thc whole of the NOTE.
In column 9, line IS, delete '8' and substitute '12'.
i n thc drawing delete dimension 'K' and substitute 'k'.
TABLE 16/11. Integral grey cast iron flanges. Under the heading delete 'All
TABLE 16/12. Malleable cast iron Integral flanges. Under the heading delete
TABLE 16/21. Integral copper alloy flanges. Under the heading delete 'All
In the drawing delete dimension 'K' and substitute 'k'. -
TABLE =/l. Integral steel flanges. Under the heading delete 'All dimensions
TABLE 25/2. Steel welding neck finges. Under the heading delete 'All dimensions
TABLE 25/3. Steel plate flanges for welding. Under the heading delete 'All
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
dimensions are !n millimetres'.

TABLE S/S. Steel slipon boss flanges for weldlng. Under the heading delete 'All
Delete the drawing and substitute the following:

BSI B S U 4 5 0 4 : PARTaL 69 L b 2 4 6 6 9 0278064 3
ar.e in millimetres'.
TABLE 25/11. Internal grey cast iron Ranges. Under the heading delete 'All
TABLE 25/12 Malleable cast iron Integral flanges. Under the heading delete 'All
dimensions are in miilimetre~'.
TABLE 25/21. Integral copper alloy flanges. Under the heading deletc 'All
TABLE 40/1. Integral steel flanges. Under the heading delete 'All dimensions
Delete the whole of the NOTE.
TABLE #/2. Steel welding neck flanges. Under the heading delete 'All dimensions
TABLE 4/3. Steel plate flanges for weelding. Under the heading delete 'All
TABLE 4û/5. Steel slipon boss flanges for welding. Under the heading delete
In the drawing delete dimension 'K' and substitute 'P.
TABLE 4û/& Steel plate blank ñanges. Under the heading delete 'All dimensions
In the heading 'NOTE 1' delete '1'.
Delete the whole of NOTE 2.
TABLE 4/21, Integral copper d o y flanges. Under the heading delete 'All
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
In the drawing delete dimension 'K' and substitute 'k'.
TABLE (%/l.Integral steel flanses. Under the heading delete 'All dimensions
TABLE 64/2. Steel welding neck fianges.Under the hcading delete 'All dimensions

BSI B S 8 4 5 0 4 : P A R T * L 69 1624667 0 2 7 8 0 6 5 5
TABLE ó4/3. Steel plate flanges for we:&!.!.. Under the heading delete 'All
TABLE lûû/l. Integral Steel Ilanges. Under the heading delete 'All dimensions
TABLE l b / X Steel weldlng neck flanges. Under the heading delete 'Ali
TABLE 100/3. Steel plate flanges for welding. Under the heading delete 'All
dimensions are in dllimetrcs'.
TABLE 160/1. Integral steel flanges, Under the h&ding delete 'All dimensions
Dclete the whole of the NOTE.
TABLE 160/2. Steel weldlng neck flanges. Under the heading delete 'All
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
TABLE 160/3. Steel plate flanges for welding. Under the heading deiete 'All
TABLE 250/1. Integral stecl flanges. Under the heading delete 'All dimensions
TABLE 250/2. Steel welding neck flanges. Under the heading delete 'All
dimensions are in millimctres',
TABLE 320/1. Integral steel flanges. Under the heading delete 'All dimensions
TABLE 320/2. Steel welding neck fianges. Under the heading delete 'All
Delete the whole of the 'NOTE'.
TABLE 400/1. Integral steel flanges, Under the heading delete 'All dimensions
In column 6, line 3, delete 'M24' and substitute 'M2O'.
In column 8, line 3, deletc '26' and substitute '22'.
TABLE 400/2. Steel welding neck flanges. Under the heading delei: 'All
In column 8, line 3, delete 'M24'and substitute 'M20'.

B S I BS*4504: P A R T * % 69 1624669 0278066 7 W
AMD 837
Amendment Slip No. 2, published 3 January, 1972

to BS 4504 :1969
Flanges and bolting for pipes, valves and fittings
Metric series
Revised text
Forewd. Delete the last two sentenctb of the sixth paragraph.

Clause 1. Scope.Insert the following new paragraph at the end of Clause 1 :
'For the purpose of interchangeability in the mating of flanges, the dimensions
which relate to the outside diameter of the flange, pitch ckcle diameter of drilled
holes, and the number and size of bolts, shall apply regardless of the materials
from which the flanges are manufactured.'
Clause 4.1 Matertals. Delete the existing text of this clause and substitute the
following:
'4.1 Matedab. Materials shall be those given in Tables A I and A2 except that
alternative materials may bc used provided that their mechanical properties are
not inferior at the operating temperature. Whm there is an appropriate
application standard it is the responsibility of the purchaser to ensurs that the
materials comply with the requirements of that standard. In this respect attention
is drawn to BS 806 and BS 759.'
Clause 4.5 Joint faces, Delete the existing text of this clause and substitute the
following:
'4.5 Joint faces
43.1 The standard form of joint face for flanges covered by this specification
shall bc as follows:
(i) Copptr alloy flanges shall have flat joint faces. When a copper alloy
flange is bolted to a flange of any other material the raised face on that
other fiange shall bc removed. The inevitable reduction in thickness is
acceptable.
(2) Ductile, grey and malleable cast iron integral fianges shdi have raised
joint faces as shown in the tables unless specified otherwise by the
purchaser.
(3) Malleable cast iron screwed flanges shall have ñat joint faces.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BSs4504: P A R T * I , 69 W 1624667 0278067 9
(4) Stcel flangcs shall have raiscd joint l a a s except that blank flanges may
be flat faced o r have a spigot at the option of the manufacturer.
4.5.2 Where it is impractical for the manufacturer to provide a raised joint face
on cast iron or steel flanges the flange may be flat faced, its thickness being in
accordance with the values specified for dimension 'b' elsewhere in this standard,
4.5.3 Where full face gaskets are used with flat faced flanges it is the responsi-
bility of the user to ensure the suitability of this type of gasket and the grade
of bolting for the particular duty and prcssure loading.'
Clause 5.1 Materials and threads. Insert the following after the first paragraph:
'Frec cutting steel for bolts, stud bolts and nuts shall only be permitted when
specified by the purchaser, and its use shall be restricted to the temperature
range -10 'C to 100 "C for nominal pressures up to and including 16 bar.'
Table 10/2. Steel welding neck fianges

Add the following:
Table 10/3. Steel plate Ranges for welding

Add the following:
Table 10/8. Steel plate blank Bang=

Add the following:
I
No*
size
450 I I
2
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*4504: P A R T * I 69 Lb24669 0278068 O m
Table lall. Integral steel flanges

Add the following:
Table 16/2. Steel welded neck flanges

Add the following:
Table 16/3. Steel plate flanges for welding

Add the following:
Table 16/8. Steel plate blank flanges

Add the following:
Nom. - Flange Driillng

rlzc D k
450 610 34 3 O w
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BS*4504: PART*3 6 9 3624669 0278069 2
Table U/2. Steel welding neck fhnges

Add the following:
I I I %;^3 I 1 o
Table 25/3.Steel plate Ranges for welding
Add the following:
y2 ;
: que;2 Bolting r13i ~
450 457.2 M33
Table 25/8. Steel plate blank flanges

Add the following:
Drilling
da
36
Table 25/11, Integral grey cast iron ñanga

Add the following:
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S U 4 5 0 4 : P A R T * L 6 9 L b 2 4 6 6 9 0278070 9
Tables 2.512, 612, 1012, 1612, 2512, 4012, 64th 10012, 16012, W12, 32012 pnd
40012. Steel welding neck flansea
Insert on the diagrams 'r* and an arrow pointing to the transition radius between
the taper and parallel portions of the welding neck, as in the typical illustration
below.
5
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * q 5 0 4 : PART*3 69 m 3 b 2 4 b b î 0278073 O m
.,*I ~ .( p .--I.) . , i .. .*;:**1 1- ,

. NOjomlN~dZ4
-- b
.-
15 6 ~
20 . PI' 6
25 8
32 8
40 9
50 11
65 13
80 13
loo 16
I
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Table 25/21. Integral copper alloy flanges
Delete the values in Column h, and substitulc the following:
~~
Nomlnil size
~
I b
15 8
20 8
25 9
32 9
40 11
50 11
65 13
80 14
100 17
Table 40/21. Integral copper illoy flanges
Delete tho values in Column b, and substftutc tho following:
Nomlnil i l t e
15
20
25
32
40 13
50 13
65 14 .
80 16
100 19

E S 1 BSU4504: P A R T * 1 69 1624669 0 2 7 8 0 7 2 2 m
, AMD861
- Amendment Slip No. 3,-pÜbgshed 15 February, 1972

*m-.
~
Flanges and b
. ~
.- -- . .
. . Metric series ,
Revised text
Section 1, Scope
Add the following before the second paragraph:

'Details of ductilc iron flanges arc spacificd in ES 4772.'
Add the following before the Notes at the end of the section:
'It should be noted, liowcvcr, that full face gaskets are necessary for copper alloy integral flanges up to 100 mm nominal
diameter.'
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
C l a w 4,l Materiais
Add tHe following paragraph at the end oí this clause:

'Certified materials are specified lor carbon stecl Ranges lor use at temperatures iricxccss of 400°C and recommended for
alloy stecl Ranges for use at temperatures in excess of 475°C Representative clevatcd temperalure tests at the tempera-
ture or tcmpcratures specified by the purchaser shall not bc rcquired for material specificd to the order provided the
manufacturer has obtained certification approval for the supply of material covered by Ihcrelcvantmaterial spcclficaiion,
following the procedure described in BS 3920, which lays down conditions undcr which he shall demonstrate that the
sttel In question consistently has the properties specified in thc rclcvant material specification.'
I
I
Table Al. Pressure/temperature ntlngs for steel fiangeji
Dcletc Table A I and its footnotes and substitute ihc table attached. I-' *
Table A2. Preqsure/temperaturo ratings for grey and molleablc casi Iron and copper alloy Ranges.
Undcr thc heading 'Bolts and stud bolts', in the last line of 'Nominal prcssurc 25 bar', substitute '64' for '4.6'. in the same
linc, undcr tho heading 'Nuts' subslitutc '6' for '4'.
Undcr lhe hcadlng 'Bolls and stud bolls', in the last linc of'Nominal prcssurc 40 bar', substitute '6.6' for '4.6'. In thc same
line, undcr lhe heading 'Nuts' rubsîitute '6' for '4',
. Gr3

BSI B S * 4 5 0 4 : P A R T 8 1 69 E 1 b 2 4 6 6 7 0278073 4 E
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

B S I BS*4504: P A R T * l 69 m 3b246b9 0278074 b
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
tu 0
w s

B S I BSX4504: PART*L b ï = Lh2Llhhï 0278075 8 I
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI B S * 4 5 0 4 : PART*l bî = 3b24bbî 027807b T W
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---

BSI BSU4504: P A R T U L 69 362qbbï 0278077 L
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
i

BSI B S * 4 5 0 4 : PART*l bî L b 2 4 b b î 0278078 3 m
.- ..
AMD 14&S
Amendment Slip No.4, ptibiished 28 June, 1974.

to ES 4504 : 1969
Flanges and boIting for pipes, vaives and fittings

Metric series
Rcvised tcxt
c page 6. .4ùd ‘Part 1 : ’and ‘Part 1. Ferrous’ t o tlie
Ccveï, lide l i ~ g 2nd
!3S n m b e : 2nd title so that they rcad:
’BS4504: Patt 1 : 1969
Flanges and bulting for pipes, valvzs and fittings
Metric series
Part 1. Ferrous’
I‘iige 2. In tlia list of rcfcreiicc stafidxds deletc BS 1400, BS 2372, and
LIS 2874.
Delete tlie pcnulliinate refcrcnce and substitute
‘BS4772. Ductile iron pipes and fittings.’
Cuctcnts. Delste the fo!lowing:
‘Table 16/21. Integral coppcr alloy flanges. Nominal pressure 16 bar.
Table 2513 I. Integrzl coppcr alloy flanges. Nominal p r m u r c 35 bar.
Table 40/21, Integral coppcr alloy flanges. Nominal pressure 40 bar.’
Foreword. In paragraph 7 dtletc the last sentunce
...................
‘Also n o gcncrally alloy flanges’.
C h s e 1. (as amendcd hy Amendments Nos. 3 and 3). In lines 4 aiid 5
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
dciere ‘arid coppcr alloy’,

Clause 3. De!& thc last line:
‘2 1 Copper alloy-iii tegral‘.
Claine 4.3.2.1 (as uinended b y Amendment No. 2). In Line 2 delete
‘and copper alloy’.
Clause 4.3:2.2 (as amended b y Amcndnient No.3) In line 2 de!ete
‘and coppcr dloy fliingcs’.
Clause 4.5.1 (as amendcd by Aiiicndincnt No. 2). Delete item (1) and
renumScr the remaining items (i), (2), and (3) respectivcly.
Gr O

B S I BS*450Li: PART*L 69 = Lb24669 0278079 5
Tzblc A1 (as aiiicnded by Amendment No. 3). In t h title dclctc

‘and coppcr alloy’.
In colunin 1 dclctc ‘40’.
Dclcte Columns 4 , 7 , 8 , 9 , 2 n d i0 complelcly.
in Columns 5 and G delete the 12th’ 13th’ 14th. 15th’ 16th’ 20th’ 21% 23nd,
23:d, 24th’ 25th 26th’ 27th, 28th and 29th lines of values.
In the Ibth lin$ of valucs delete tlie design prcssurc ratinss @ven i3 colucins
11 to 17.
Iii th6 24th line of values dclets the design pressure ratings givcn in co!umns
11 t o 17.
In the 29th line of values delete thc design prcssurc ratings givcn in columns
l i to 17.
Table D. Delctc tlie following columns completely:
‘16121
25/21
40121’
Table 16/11. Delete this table.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Table 13/21. Dclcte this table.
Ta‘ulc40/21. Delete this tablc.

AILIL) 1756
Amendment Slip No. 9, pubIished 31 JuIy 1975

-_ .
.
to BS 4504 :.Part 1 :1969
. .
Flanges and bolting for"pipes, vaIvp and
fittings. Metric series
Part '1: Ferrous -
. -.
Revised text
UDCnumber. Delete the existing UDCnumberand substifute'621.643.d034.669.1'.
Page 2. Insert the following in the list of British Standards, maintaining the numerical order of references:
'BS 4439. Screwed studs for general purposes.
BS 4882. Bolting for flanges and pressure containing purposes.'
Foreword. Insert the following new paragraph:
'IT SHOULD BE NOTED THAT. AT THE TIME OF ISSUING THIS AMENDMENT, PROPOSALS ARE
UNDER CONSIDERATION WITHIN CEN/WG 74. FLANGES, EFFECTIVELY RECOMMENDING THAT
THE USE O F DIN-BASED FLANGES IN BS 4504 BE LIMITED TO A MAXIMUM PRESSURE OF 40 BAR.
IF THESE PROPOSALS ARE AGREED AND RESULT IN THE PUBLICATION OF A EUROPEAN
STANDARD, BS 4504 WILL BE AMENDED ACCORDINGLY.'
Clause 1. Scope. Delete the number of this clause and substitute '1.1'.
in line4. imniediately before 'cast iron', delete 'grey'.
Delete 'Details ofductile iron flanges are specified in OS 477L'and substitute the following:
'Details foi.ductile iron pipes and ductile iron pipc fittings aie specified in ES 4772.'
Imrncdiatcly after this ncw sentence insert the following new paragraph:
'Details of flanges for grey iron pipes and grey iron pipc fittings are specified in BS 4622.'
New clause. Insert the following new Clause 1.2:
'1.2 DEFINITION
Nomínal size (DN). A nunierical designation of size which is common to all components in a piping system other than
those using valves, fittings, couplings or tubes which are designated by the outside diameter. It is a convenieiit round
nuinber for reference purposes and it is norinally only l o o d y related to manufacturing dimensions.'
Clnuse 3. Designation. At the end of paragraph 2, immediately after 'nominal pressure', insert '(PN)'. In item 1 I, delete
'Grey'.
Clause 4.2 Machining of Ranges. Delete the existing text entirely and substitute the following:
'4.2.1 All flanges shall bc free from leniinations and surface defects.
4.2.2 Flanges shall be finished as follows.
(I) All flanges shall have their jointing surfaces machine finished. The finish ofjointing surfaces up to and including
PN 40 shall not be coarser than given in the following table appropriate to the method ohachining. For flanges
above PN 40 i t i s recommended that the surface finish should comply with the requirements of BS W .
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
BS 1134
Turning 12.5 50 t087-5 N.10

Oihcr than turning
NOTE.Thc tcrm'iurning' includes any mcthod or machining producing concentric or spirol grooves.
(2) Flange outside diameters may be unmachined unlessa mach.¡ne finish is specified by the purchaser.
(3) Unless otherwise specified by the purchascr, all bolt holes shall be drilled, shall be equally spaced on the pitch
circle dianietcr and, in the case of integral flanges, shall be drillcd ofl-centre,
(4) l3earing surfices for nuts shall be parallel to the Rangejointing face within 1 O.'
Clause 4.3 Tolemnces on flange dianietcr, thickness and length of weldfng necks. Delete the asterisk a i the end of this
titk iintl tlcl1:ic i h c i i ~ S ~ ~ i í ifiiotnotc~.
tcd

BSI B S * 4 5 0 4 : P A R T 8 1 69 M l b 2 4 6 6 9 02780B1 3 =
Clause 4.4 Finish of joint surfaces. Delete this clause entirely.

Clause 4.5 Joint faces. Renumber tliis clausc as 4.4.
Clause 4.5.1. Renumber this clause as 4.4.1.
I n iten?( I ) dclcle 'Ductile, grey and malleable'.
. Clause 4.5.2. Rcnumbcr this c l a w as 4.4.2.
Clause 4.5.3. Renumber this clausc as 4.4.3,
Delete the existing text and substitute the following: - -- .
'It is thc responsibility of the user to select gasket material which is suitable for the fluid at the intended working
temperature and pressure conditions.'
I
Clause 5.1 Materials and threads. Delete paragraphs 2,3 and 4.
Renunibcr the existing paragraph 1 as 5.1 . I ,
Insert the following new subclauses:
'5.1.2 The dimensions and finish of studs and hcxagon hcaded bolts with hcxagon nuts shall comply with the require-
ments of BS 3697, BS 4190 or OS 4439 as appropriate.
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
5.1.3 Thc dimensions and finish of stud bolts with hexagon nuts shall comply with the requirements of BS 4882:
1973, Sections I and 2.
5.1.4 Stud bolts may be of the forms shown in BS 4882 except that form 'b' applies only to stud bolts of other than
iilloy SICCI.
5.1.5 Free cutting stccis for studs, bolts, stud bolts and nuts shall only be permitted when specified by the purchaser,
and their use shall be restricted to the temperature range -10 "C to Io0 "C for nominal pressures up to and including
I6 bar.
5.1.6 Where washers ;ire used they shall be of an appropriate niaierial and their dimensions shall comply with the
rcqiiircnicnts of Table 3 of BS 4320:1908.
Siaiidurd black normal series washers complying with the requirements of BS 4320 may be used for the temperature
rntige - 30 'CIO 260 "C.'
Clause 5.2 Stud bolts. Delete this clause entircly.
Ciaiise 5.3 \Yudiers. Delete this clause entirely.
Clausc 7. I-lydriiulie testing of'flanges. Delete the note at the end of this clause.
Clause 8. Deta¡¡s to be supplied by the purchnser when ordering flanges and/or bolting. In item (6) delete '(see 4.2, 4.3
iiiitl4.4)' and substitute '(scc4.2and 4.3)'.
Fig, I , Stud bolt screwed at cach end and plain in the rentre. Delete this figure entirely.
Fig, 2. Stud bolt screwed full length. Delctc this figiirc cntircly.
Fig. 3. Sliapcd stud bolt. Dclctc this figure entirely.
0
Tnhle Al. Prcssurc/tcmpernture ratlngs for steel flangcs. In the footnotc marked 'i'on pages IO, I I , 12, 13 and 14
delete '250 'C'and substitute '300 O C ' .
l'iible A2, I'rcssurc/tcnipcrntiirc ratings for grey and inallcablc cast iron tlangcs. Insert an asterisk at the cnd of the
. iiilcaiid inscrt ihc following footnoic:
"Tlic tensile strcnyih of the cast iron sclccted for the appropriate standard flungc thickness shall not fall below:
( 1 ) for iioniinal prcssiircs up to and including 16 bar: 180 N/nima;
(2)for noiiiinul pressures greater than 16 bar: 220 N/mma.'
For ndiiiinal pressure 2 3 , in column 2 of the tablc, deletc 'Gradc IO' and 'Grade 12' and substitute 'Gradc 12' and
'Grade 14' respectively.
For noniinal pressure 6, in column 2 of the table, dclcic 'Grade IO' and 'Gradc 12' and substiiutc 'Grade 12' and
'Gradc 14' respectively.
For noiiiinal piessurc IO, in caliinin 2 of the table, deletc 'Grade IO' and 'Gradc 12' and substitute 'Grude 12' and
'Grade 14' rcspcctively,
For nominal prcssurc 16, in coliinin 2 of the tuble, delete'uradc W a n d substitutc'Gradc 14',
'I'ublc U. Sunininry of contents of f l u n p lablcs. For noniinal size 450 mm inscrt 'X' under thc column hcadings 6/2,
6/3,6/6,6/l I, 10/2, lop, i0/8, IW, 16/2, 16/3, 16/8, 25/Il 25/2,25/3,25/8,25/11,40/1,40/2,40/3 add 40/5.
T a b h 23/11, 6/11, 6/12, iO/ii, 16/1, 16/Jl, 25/11, 25/12, 40/11, a/I,iOO/i, laO/l, zsO/i, 320/1 and 400/1. Insert
thc rollowiny foolnotc bcneuih cuch of thcsc tubles:
'
'NOTE.Alternative ncck form, shown doitcd, to havc u niuximum draft angle of 12 O.'
Tubk 6/3,Steel plate ílungcs for wclding. For nominal size 80 mni, in column 5 of the table, deletc '120' and substituto
'128'.

--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---
Table 40/1, Integral steel flanges. Insert the following details for nominal size 450 mm:
. .-
Nom. s t ~ c dl û b hl d. f Bolting NO. da . k da -h. r

-
-
-.
450 457.2 685 50 135 560 4- M36 ' 20 39 610 '500 20 12
-..--Num. size
450
4
457.2
D
-___
685
h
~-
68
d,
560
I; ~~lti 1 No.
20
4
39
k
610
Noin. size D h 4 Dolilng 4 k

--------- --- NO.
450 685 54 425 M36 20 39 610

m-
.-a
@J
p.
rrl
ci
X
3
--``,,,`,`,`````,,,,,,,,,,,`,,``-`-`,,`,,`,`,,`---


BS 4504-Part 1

Uploaded by

Copyright:

Available Formats

BS 4504-Part 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BS 4504-Part 1

Uploaded by

Copyright:

Available Formats

1 B S I BS*4504: P A R T S 1 67 1 6 2 4 b b î 0277780 T m'

BRITISH STANDARD 4504 : 'Part 1 :1969

Copyright British Standards Institution

BS 21, Pipe threads.

BS 1501. Steels for fired and unfired pressure vesscls. Plates.

’BS4439. Screwed studs for gcneril purposcs. .

Copyright British Standards Institution

I. Scopc . . . . . . . pressure 16 bar . . . . . . 36

prcssurc 6 bar , . . 20 prcssurc 25 bar . . so

6/13. Mallcnblc cast iron scrcwed boss flangcs. prcssure 40 bar 57

prcssurc IO bar 29 64/1. Integral stcel flanges. Nominal prcssiirc 64 bar 60

Copyright British Standards Institution

Copyright British Standards Institution

*Associated Offices' Technical Committee *Institution of Civil Engineers

Copyright British Standards Institution

BRITISH STANDARD SPECIFICATION FOR

h SHOULD-BE.NOTED THAT. AT-THE TIME ÖF ISSUING <HI; AMENDMENT, PROPOSALS A R E

Copyright British Standards Institution

The types and materials of gaskets used shall be agreed .

1.1 SCOPE between the purchaser and the manufacturer.

Copyright British Standards Institution

2. DESIGN TEMPERATURE AND PRESSURE

shock conditions. Where moderate shock (such as may

11. &ey cast iron-integral.

12. Malleable cast iron-integral.

Copyright British Standards Institution

hlclhod of mnrhlnlng 1 R. I R.= 1 Rr

4.3 Tolerances on Bange &meter, thickness and length of

4.3.1 Outside diameter (O)

43.2.1 Flanges integral with valves and fittings (other than

Over 70 up to 100 inclusive 3.5.0 3.104

a Ductile iron pipo filtlngs and accessories for pteuure pipelines : A

6.2.1 ScrewedJunges. Screwed flanges shall be screwed in

Copyright British Standards Institution

BS 4504 : Part i : It/!

Copyright British Standards Institution

Copyright British Standards Institution

Copyright British Standards Institution

Copyright British Standards Institution

Copyright British Standards Institution

Copyright British Standards Institution

Copyright British Standards Institution

A i rlrrrrd Marrh. 1971

Copyright British Standards Institution

Copyright British Standards Institution

TABLE2q2. STEEL WELDING NECK FLANGES

NOTE, For nominal iIzes 10 to loo0 usa Tablo 6/2,

1 For weld preparation see

Copyright British Standards Institution

NOTE. For nominal i h s IO to loo0 uso Table 6/3.

Copyright British Standards Institution

TABLE 23/11. INTEGRAL*GREYCAST IRON FLANGES

NOTE.For nominal alzes 10 to loo0 usa Table 6/i 1.

Raked face Neck

2 200 2 405 36 2 295 6 2 340

3200 3 430 44 3 310 6 3 360 3 268 12

A IJOTE. A l t e r n a t i v e neck form, shown dotted, t o have a maximum d r a f t angle of 12'

Copyright British Standards Institution

TABLE 6/2. STEEL WELDING NECK FLANGES

Associated Offices' Technical Committee Institution of Civil Engineers