EN 1092-1

FLANGES
WELLGROW INDUSTRIES CORP.

Plate Flange
Loose Plate Flange With Weld-on Plate Collar
Loose Plate Flange With Weld-Neck Collar
Blind Flange
Weld-Neck Flange
Hubbed Slip-On Flange
Hubbed Threaded Flange
Integral Flange
Lapped Pipe Ends

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 Flanges Summary Chart

Rated Pressure (in bar)

(1 bar = 14.5 psi = 100 kPa)
Description
6 10 16 25 40 63 100 160 250 320 400

01 Plate flanges for welding V V V V V V V

Loose plate flanges with

02 V V V V V
weld-on plate collar

Loose plate flanges with

04 V V V V V
weld-neck collar

05 Blank <blind> flanges V V V V V V V

11 Weld-Neck Flanges V V V V V V V V V V V

Hubbed slip-on flanges for

12 V V V V V V V
welding

13 Hubbed threaded flanges V V V V

21 Integral flanges V V V V V V V V V V V

32 Weld-on plate collars V V V V V

33 Lapped pipe ends V V V V V

34 Weld-neck collars V V V V V

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Flange Facing Type EN 1092-1

Note 1: For facings types B, D, F and G, the transition from the edge of the raised face to the flange shall be radius,
or chamfer at the choice of the flange manufacturer.
Note 2: B1 and B2 are raised face (type B) for different applications.
For flanges and collars (except types 33, 36 and 37) with facing types A, B1, E and F, turning shall be
carried out with a round nosed tool in accordance with Table as hereunder.

Surface finish for jointing faces

Radius of tool nose Raa Rza
Method of
Facing types mm μm μm
machining
Min. Min. Max. Min. Max.
A, B1 b, E, F Turning c 1.0 3.2 12.5 12.5 50
B2 b, C, D, G, H Turning c - 0.8 3.2 3.2 12.5
For certain applications, e.g. low temperature gases, it may be necessary to stipulate closer control to the surface
finish.
a} Ra and Rz are defined in EN ISO 4287.
b) Types B1 and B2 are raised face (type B) flanges with different specified surface roughness values.
B1 : Standard facing for all PN numbers.
B2 : Only if agreed between the purchaser and the flange manufacturer.
c) The term 'turning' includes any method of machine operation producing either serrated concentric or serrated
spiral grooves.

Flanges type 05 up to PN 40 and collars (except types 33, 36 and 37) shall have type A facing, other
flanges shall have type B1 facings; unless type B2 facing is agreed between the purchaser and the supplier.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Flange Facing Dimensions EN 1092-1

Type A Type B Type C Type D Type E Type F Type G Type H

flat face raised face tongue face groove face spigot recess O ring recess O ring groove
(B1 and B2)

d1 f1 f2 f3 f4 w** x y z** a≈ R
DN PN2.5* PN6* PN10 PN16 PN25 PN40 PN63 PN100 PN160 PN250 PN320 PN400
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm Mm mm mm mm
10 35 35 40 40 40 40 40 40 40 40 40 40 24 34 35 23 -
15 40 40 45 45 45 45 45 45 45 45 45 45 29 39 40 28 -
20 50 50 58 58 58 58 58 58 58 58 58 58 2 36 50 51 35
25 60 60 68 68 68 68 68 68 68 68 68 68 43 57 58 42
32 70 70 78 78 78 78 78 78 78 78 78 78 4.5 4.0 2.0 51 65 66 50 2.5
40 80 80 88 88 88 88 88 88 88 88 88 88 61 75 76 60 41°
50 90 90 102 102 102 102 102 102 102 102 102 102 73 87 88 72
65 110 110 122 122 122 122 122 122 122 122 122 122 95 109 110 94
80 128 128 138 138 138 138 138 138 138 138 138 138 106 120 121 105
100 148 148 158 158 162 162 162 162 162 162 162 162 3 129 149 150 128
125 178 178 188 188 188 188 188 188 188 188 188 188 155 175 176 154
150 202 202 212 212 218 218 218 218 218 218 218 218 183 203 204 182
5.0 4.5 2.5 32° 3
200 258 258 268 268 278 285 285 285 285 285 285 285 239 259 260 238
250 312 312 320 320 335 345 345 345 345 345 345 - 292 312 313 291
300 365 365 370 378 395 410 410 410 410 - - - 343 363 364 342
350 415 415 430 438 450 465 465 465 - - - - 395 421 422 394
400 465 465 482 490 505 535 535 535 - - - - 4 447 473 474 446
50 520 520 532 550 555 560 560 560 - - - - 497 523 524 496
500 570 570 585 610 615 615 615 615 - - - - 549 575 576 548
5.5 5.0 3.0 27° 3.5
600 670 670 685 725 720 735 735 - - - - - 649 675 676 648
700 775 775 800 795 820 840 840 - - - - - 751 777 778 750
800 880 880 905 900 930 960 960 - - - - - 856 882 883 855
900 980 980 1005 1000 1030 1070 1070 - - - - - 961 987 988 960
1000 1080 1080 1110 1115 1140 1180 1180 - - - - - 1062 1092 1094 1060
1200 1280 1295 1330 1330 1350 1380 1380 - - - - - 1262 1292 1294 1260
1400 1480 1510 1535 1530 1560 1600 - - - - - - 1462 1492 1494 1460
6.5 6.0 4.0 28° 4
1600 1690 1710 1760 1750 1780 1815 - - - - - - 1662 1692 1694 1660
1800 1890 1920 1960 1950 1985 - - - - - - - 1862 1892 1894 1860
2000 2090 2125 2170 2150 2210 - - - - - - - 2062 2092 2094 2060
2200 2295 2335 2370 - - - - - - - - - - - - - - - - - -
2400 2495 2545 2570 - - - - - - - - - - - - - - - - - -
2600 2695 2750 2780 - - - - - - - - - - - - - - - - - -
2800 2910 2960 3000 - - - - - - - - - - - - - - - - - -
3000 3110 3160 3210 - - - - - - - - - - - - - - - - - -
3200 3310 3370 - - - - - - - - - - - - - - - - - - -
3400 3510 3580 - - - - - - - - - - - - - - - - - - -
3600 3720 3790 - - - - - - - - - - - - - - - - - - -
3800 3920 - - - - - - - - - - - - - - - - - - - -
4000 4120 - - - - - - - - - - - - - - - - - - - -
* Flange facing types C, D, E, F, G and H according to Figure 4 are not used for PN 2,5 and 6.
** Flange facing types G and H according to Figure 4 are only used for PN 10 to PN 40.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Wall thickness and end preparation EN 1092-1

Weld-end preparation for flanges types 11 and 34

Unless otherwise specified, for flanges in accordance with this European Standard the welding end connections
given in A1 to A3 shall be used. Additional types of welding ends are specified in EN ISO 9692-2 and example
of designs in EN 1708-1 and may be used by agreement between the component or pressure equipment
manufacturer and the flange manufacturer.

● Wall thickness S ≦ 3 mm: Flanges/collars may be delivered with square cut ends.
● Wall thickness 3 < S < 22: Bevelled ends with an angle of 30° +5° −0 and root face of (1,6 ± 0,8) mm.

● If flange wall thickness (S) > pipe wall thickness (T), the inner diameter shall be chamfered with an angle of
15°+5°−0 to match (see A3).

A1 — Welding end connection for wall thickness S up to 22 mm

6 min. for ≦ DN200 (H3 length)

A2 — Welding end connection for wall thickness S ≧ 22 mm

x
6 min. for ≦ DN200 (H3 length)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Wall thickness and end preparation EN 1092-1

Weld-end preparation for flanges types 11 and 34

A3 — Permissible bevel design for unequal wall thickness

S Flange wall thickness

Sp Reduced flange wall thickness

NOTE 1: For flanges required to connect to non-austenitic steel pipe of nominal wall thickness less than 4,8 mm, the welding ends should be
finished to a slight chamfer or be square, at the option of the flange manufacturer, if nothing else has been agreed between flange
manufacturer and purchaser or pressure equipment manufacturer.
NOTE 2: For flanges required to connect to austenitic stainless steel pipe of nominal wall thickness 3,2 mm or less, the welding ends should
be square cut ends.
NOTE 3: The mating wall thickness of the flange (Sp) shall match to the pipe wall thickness (T).

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Wall thickness and end preparation EN 1092-1

Wall thickness for flange type 11

PN2.5 PN6 PN10 PN16 PN25 PN40 PN63 PN100
ψA
S Sp S Sp S Sp S Sp S Sp S Sp S Sp S Sp
17.2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
21.3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3.2 2
26.9 2.3 2.3 2.3 2.3 2.3 2.3 2.3 2.3 2.3 2.3 2.3 2.3 2.6 2.3 3.2 2.3
33.7 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 3.6 2.6
42.4 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.9 2.6 3.6 2.9
48.3 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.9 2.9 3.6 3.2
60.3 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 4 3.2 4 3.6
76.1 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 4 3.6 4 4
88.9 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 4.5 4 5 5
114.3 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 4.5 4.5 5.6 5.6
139.7 4 4 4 4 4 4 4 4 4 4 4 4 5.6 5.6 6.3 6.3
168.3 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 6.3 6.3 8 8
219.1 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 7.1 7.1 8.8 8.8
273.0 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 7.1 7.1 7.1 7.1 8.8 8.8 10 10
323.9 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 8 8 8 8 11 10 12.5 12.5
355.6 7.1 7.1 7.1 7.1 7.1 7.1 8 8 8 8 8.8 8.8 12.5 10 14.2 14.2
406.4 7.1 7.1 7.1 7.1 7.1 7.1 8 8 8.8 8.8 11 11 14.2 11 16 16
457 7.1 7.1 7.1 7.1 7.1 7.1 8 8 8.8 8.8 12.5 12.5
508 7.1 7.1 7.1 7.1 7.1 7.1 8 8 10 10 14.2 14.2
610 7.1 7.1 7.1 7.1 8 7.1 10 8.8 11 11 16 16
711 7.1 7.1 8 7.1 8.8 8 10 8.8 14.2 12.5
813 7.1 7.1 8 7.1 8.8 8 12.5 10 16 14.2
914 7.1 7.1 8 7.1 12.5 10 12.5 10 17.5 16
1016 7.1 7.1 8 7.1 12.5 10 12.5 10 20 17.5
1219 8 7.1 8.8 8 12.5 11 14.2 12.5
1422 8 7.1 8.8 8 14.2 12.5 16 14.2
1626 8.8 8 10 9 16 14.2 17.5 16
1829 10 10 11 10 17.5 16 20 17.5
2032 11 10 12.5 11 17.5 16 22 20
2235 11 10 14 12.5 20 18
2438 11 10 15 14.2 22.2 20
2620 11 10 16 14.2 25 22.2
2820 11 10 17 16 25 22.2
3020 11 10 20 16 32 24
3220 11 10 20 16
3420 11 10 22 17.5
3620 11 10 22 17.5
3820 11 10
4020 11 10
Sp Valves shall match those given in EN 10220 respectively EN ISO 1127.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Wall thickness and end preparation EN 1092-1

Wall-end preparation for type 35

Chamfer A Chamfer B

Wall thickness for flange type 35

PN2.5 PN6 PN10 PN16 PN25 PN40

ψA Chamfer
S Sp S Sp S Sp S Sp S Sp S Sp
17.2 3 2 3 2 3 2 3 2 3 2 3 2
21.3 3 2 3 2 3 2 3 2 3 2 3 2
26.9 3 2 3 2 3 2 3 2 3 2 3 2
33.7 3 2 3 2 3 2 3 2 3 2 3 2
42.4 3 2 3 2 3 2 3 2 3 2 3 2
48.3 3 2 3 2 3 2 3 2 3 2 3 2 A
60.3 3 2 3 2 3 2 3 2 4 2.6 4 2.6
76.1 4 2 4 2 4 2 4 2 5 2.6 5 2.6
88.9 4 2 4 2 4 2 4 2 6 2.6 6 2.6
114.3 4 2 4 2 4 2 4 2 6 3.2 6 3.2
139.7 5 2 5 2 5 2 5 2 6 3.2 6 3.2
168.3 6 2 6 2 6 2 6 2 8 3.2 8 4
219.1 6 2.6 6 2.6 6 2.6 6 2.6 8 3.2 10 5
273 8 3.2 8 3.2 8 3.2 8 3.2 10 5 12 6.3
323.9 8 3.2 8 3.2 8 3.2 10 4 10 6.3 12 8
355.6 8 3.2 8 3.2 8 3.2 10 4 12 6.3 14 8
406.4 8 3.2 8 3.2 8 3.2 12 5 14 8 16 10
457 8 3.6 8 3.6 8 3.6 12 5 15 8 B
508 8 4 8 4 8 4 12 6.3 16 10
610 8 5 8 5 10 5 12 8 18 10
711 8 5 8 5 10 6.3 14 8 20 14.2
813 10 6.3 10 6.3 12 6.3 16 10 20 14.2
914 10 6.3 10 6.3 12 8 18 10
1016 12 8 12 8 12 8 18 10
1219 14 10 14 10 16 10

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 Wall thickness and end preparation EN 1092-1

Wall-end preparation for types 36 and 37

Chamfer A Chamfer B

Wall thickness for flange types 36 and 37

PN2.5 to PN10 PN16

ψA Type 36 Type 37 Type 36 Type 37 Chamfer
S Sp S Sp S Sp S Sp
17.2 2 2 2 2 2 2 2 2
21.3 2 2 2 2 2 2 2 2
26.9 2.6 2.6 2 2 2.6 2.6 2 2
33.7 2.6 2.6 2 2 2.6 2.6 2 2
42.4 3.2 3.2 2 2 3.2 3.2 2 2
A
48.3 3.2 3.2 2 2 3.2 3.2 2 2
60.3 3.2 3.2 2 2 3.2 3.2 2 2
76.1 3.2 3.2 2 2 3.2 3.2 2 2
88.9 3.2 3.2 2 2 3.2 3.2 3.2 3.2
114.3 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2
139.7 4 3.2 3.2 3.2 4 3.2 3.5 3.2
168.3 5 3.2 3.5 3.2 5 3.2 4.5 3.2
219.1 5 3.2 4.5 3.2 6 3.2 5.6 3.2
273 8 3.2 10 3.2
323.9 8 3.2 10 4**
355.6 8 3.2 10 4**
406.4 8 3.2 10 4**
457 8* 3.2*
508* 8* 3.2*
*These values are valid only for PN 2,5 and PN 6.
** Like chamfer B for Type 35.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN2.5 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 21 (Integral flanges)

02 (Loose plate flanges with weld-on plate collar) 35 (Weldring neck)

05 (Blank [blind] flanges) 36 (Pressed collar with long neck)

11 (Weld-neck flanges) 37 (Pressed collar)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN2.5 Flanges
Mating dimensions

Corner Radius
Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter
Outside

Outside

Neck Bore Flange Neck

Bolting Diameter thickness Collar thickness Length diameters
DN G
D K L No Size A B1 B2 C1 C2 C3 C4 F max H2 H3 H4 H5 N1 N3 R1 S
Flange type
11
11 35
21 01 01 11 11 36
01, 02, 05, 11, 21 35-37 32 02 02 21 05 32 35 36 37 05 11 11 35 36 37 11 21 13 37
10 75 50 11 4 M10 17.2 18.0 21 12 12 12 10 5 2.0 2.5 - 28 6 28 35 7 26 20 4
15 80 55 11 4 M10 21.3 22.0 25 12 12 12 10 5 2.0 2.5 - 30 6 30 38 7 30 26 4
20 90 65 11 4 M10 26.9 27.5 31 14 14 14 10 6 2.5 3.0 - 32 6 32 40 8 38 34 4
25 100 75 11 4 M10 33.7 34.5 38 14 14 14 10 7 2.5 3.0 - 35 6 35 40 10 42 44 4
32 120 90 14 4 M12 42.4 43.5 46 16 14 14 10 8 3.0 3.0 - 35 6 35 42 12 55 54 6
40 130 100 14 4 M12 48.3 49.5 53 16 14 14 10 8 3.0 3.0 - 38 7 38 45 15 62 64 6
50 140 110 14 4 M12 60.3 61.5 65 16 14 14 12 8 3.0 3.0 - 38 8 38 45 20 74 74 6
65 160 130 14 4 M12 76.1 77.5 81 16 14 14 12 8 3.0 3.0 55 38 9 38 45 20 88 94 6
80 190 150 18 4 M16 88.9 90.5 94 18 16 16 12 10 3.0 4.0 70 42 10 42 50 25 102 110 8
100 210 170 18 4 M16 114.3 116 120 18 16 16 14 10 4.0 4.0 90 45 10 45 52 25 130 130 8
125 240 200 18 8 M16 139.7 141.5 145 20 18 18 14 10 4.0 4.0 115 48 10 48 55 25 155 160 8
150 265 225 18 8 M16 168.3 170.5 174 20 18 18 14 10 5.0 4.0 140 48 12 48 55 25 184 182 10
200 320 280 18 8 M16 219.1 221.5 226 22 20 20 16 11 5.0 5.0 190 55 15 55 62 30 236 238 10

See “Wall thickness and end preparation”

250 375 335 18 12 M16 273.0 276.5 281 24 22 22 18 12 8.0 - 235 60 15 60 68 - 290 284 12
300 440 395 22 12 M20 323.9 327.5 333 24 22 22 18 12 8.0 - 285 62 15 62 68 - 342 342 12
350 490 445 22 12 M20 355.6 359.5 365 26 22 22 18 13 8.0 - 330 62 15 62 68 - 385 392 12
400 540 495 22 16 M20 406.4 411.0 416 28 22 22 20 14 8.0 - 380 65 15 65 72 - 438 442 12
450 595 550 22 16 M20 457.0 462.0 467 30 22 24 20 15 8.0 - 425 65 15 65 72 - 492 494 12
500 645 600 22 20 M20 508.0 513.5 519 30 24 24 22 16 8.0 - 475 68 15 68 75 - 538 544 12
600 755 705 26 20 M24 610.0 616.5 622 32 30 30 22 16 - - 575 70 16 70 - - 640 642 12
700 860 810 26 24 M24 711.0 721 40 30 40 - 16 - - 670 76 16 70 - - 740 746 12
800 975 920 30 24 M27 813.0 824 44 30 44 - 16 - - 770 76 16 70 - - 842 850 12
900 1075 1020 30 24 M27 914.0 926 48 30 48 - 16 - 860 74 16 70 - - 942 950 12
1000 1175 1120 30 28 M27 1016 1028 52 30 52 - 18 - - 960 74 16 70 - - 1045 1050 16
1200 1375 1320 30 32 M27 1219 ** 1234 60 32 50 - 20 - - 1160 94 16 90 - - 1245 - 16
1400 1575 1520 30 36 M27 1422 - - 38 - - - - - 1346 96 16 - - - 1445 - 16
1600 1790 1730 30 40 M27 1626 - - 46 - - - - - 1546 102 20 - - - 1645 - 16
1800 1990 1930 30 44 M27 1829 - - 46 - - - - - 1746 110 20 - - - 1845 - 16
2000 2190 2130 30 48 M27 2032 - - 50 - - - - - 1950 122 22 - - - 2045 - 16
2200 2405 2340 32 52 M30 2235 - - - 56 - - - - - - 129 25 - - - 2248 - 18
2400 2605 2540 33 56 M30 2438 - - - 62 - - - - - - 143 25 - - - 2448 - 18
2600 2805 2740 33 60 M30 2620 - - - 64 - - - - - - 148 25 - - - 2648 - 18
2800 3030 2960 36 64 M33 2820 - - - 74 - - - - - - 161 25 - - - 2848 - 18
3000 3230 3160 36 68 M33 3020 - - - 80 - - - - - - 170 25 - - - 3050 - 18
3200 3430 3360 36 72 M33 3220 - - - 84 - - - - - - 180 25 - - - 3250 - 20
3400 3630 3560 36 76 M33 3420 - - - 90 - - - - - - 194 28 - - - 3475 - 20
3600 3840 3770 36 80 M33 3620 - - - 96 - - - - - - 201 28 - - - 3652 - 20
3800 4045 3970 39* 80 M36 3820 - - - 102 - - - - - - 212 28 - - - 3852 - 20
4000 4245 4170 39 84 M36 4020 - - - 106 - - - - - - 226 28 - - - 4052 - 20
Note 1: Dimensions N1 is measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
** To be specified by the purchaser.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN6 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 21 (Integral flanges)

02 (Loose plate flanges with weld-on plate collar) 32 (Weld-on plate collars)
33 (Lapped pipe ends without determination of
05 (Blank [blind] flanges)
thickness of thickness and height)

11 (Weld-neck flanges) 35 (Weldring neck)

12 (Hubbed slip-on flanges for welding) 36 (Pressed collar with long neck)

13 (Hubbed threaded flanges) 37 (Pressed collar)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN6 Flanges
Mating dimensions

Corner Radius
Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter

Chamfer
Outside

Outside

Neck

Bore Flange Neck

Bolting Diameter thickness Collar thickness Length diameters
DN C2 G
D K L No Size A B1 B2 C1 C3 C4 E F max H1 H2 H3 H4 H5 N1 N2 N3 R1 S
Flange type
11 11 11
11 01 12 12 35
21* 12 01 13 12 12 13 36
01, 02, 05, 11, 12, 13, 21 35-37 32 02 02 21 05 02 32 35 36 37 05 13 11 11 35 36 37 11 13 21 21 37
10 75 50 11 4 M10 17.2 18.0 21 12 12 12 3 10 5 2.0 2.5 - 20 28 6 28 35 7 26 25 20 4
15 80 55 11 4 M10 21.3 22.0 25 12 12 12 3 10 5 2.0 2.5 - 20 30 6 30 38 7 30 30 26 4
20 90 65 11 4 M10 26.9 27.5 31 14 14 14 4 10 6 2.5 3.0 - 24 32 6 32 40 8 38 40 34 4
25 100 75 11 4 M10 33.7 34.5 38 14 14 14 4 10 7 2.5 3.0 - 24 35 6 35 40 10 42 50 44 4
32 120 90 14 4 M12 42.4 43.5 46 16 14 14 5 10 8 3.0 3.0 - 26 35 6 35 42 12 55 60 54 6
40 130 100 14 4 M12 48.3 49.5 53 16 14 14 5 10 8 3.0 3.0 - 26 38 7 38 45 15 62 70 64 6
50 140 110 14 4 M12 60.3 61.5 65 16 14 14 5 12 8 3.0 3.0 - 28 38 8 38 45 20 74 80 74 6
65 160 130 14 4 M12 76.1 77.5 81 16 14 14 6 12 8 3.0 3.0 55 32 38 9 38 45 20 88 100 94 6
80 190 150 18 4 M16 88.9 90.5 94 18 16 16 6 12 10 3.0 4.0 70 34 42 10 42 50 25 102 110 110 8
100 210 170 18 4 M16 114.3 116 120 18 16 16 6 14 10 4.0 4.0 90 40 45 10 45 52 25 130 130 130 8
125 240 200 18 8 M16 139.7 141.5 145 20 18 18 6 14 10 4.0 4.0 115 44 48 10 48 55 25 155 160 160 8
150 265 225 18 8 M16 168.3 170.5 174 20 18 18 6 14 10 5.0 4.0 140 44 48 12 48 55 25 184 185 182 10

See “Wall thickness and end preparation”

200 320 280 18 8 M16 219.1 221.5 226 22 20 20 6 16 11 5.0 5.0 190 44 55 15 55 62 30 236 240 238 10
250 375 335 18 12 M16 273.0 276.5 281 24 22 22 8 18 12 8.0 - 235 44 60 15 60 68 - 290 295 284 12
300 440 395 22 12 M20 323.9 327.5 333 24 22 22 8 18 12 8.0 - 285 44 62 15 62 68 - 342 355 342 12
350 490 445 22 12 M20 355.6 359.5 365 26 22 22 8 18 13 8.0 - 330 - 62 15 62 68 - 385 - 392 12
400 540 495 22 16 M20 406.4 411 416 28 22 22 8 20 14 8.0 - 380 - 65 15 65 72 - 438 - 442 12
450 595 550 22 16 M20 457.0 462 467 30 22 24 8 20 15 8.0 - 425 - 65 15 72 72 - 492 - 494 12
500 645 600 22 20 M20 508.0 513.5 519 30 24 24 8 22 16 8.0 - 475 - 68 15 75 75 - 538 - 544 12
600 755 705 26 20 M24 610.0 616.5 622 32 30 30 8 22 16 - - 575 - 70 16 70 - - 640 - 642 12
700 860 810 26 24 M24 711.0 721 40 30 40 4 - 16 - - 670 - 76 16 70 - - 740 - 746 12
800 975 920 30 24 M27 813.0 824 44 30 44 4 - 16 - - 770 - 76 16 70 - - 842 - 850 12
900 1075 1020 30 24 M27 914.0 926 48 34 48 4 - 16 - 860 - 78 16 70 - - 942 - 950 12
1000 1175 1120 30 28 M27 1016.0 1028 52 38 52 4 - 18 - - 960 - 82 16 70 - - 1045 - 1050 16
1200 1405 1340 33 32 M30 1219.0 ** 1234 60 42 60 5 - 20 - - 1160 - 104 20 90 - - 1248 - 1264 16
1400 1630 1560 36 36 M33 1422.0 - 42 56 68 - - - - - 1346 - 114 20 - - - 1452 - 1480 16
1600 1830 1760 36 40 M33 1626.0 - 80 63 76 - - - - - 1546 - 119 20 - - - 1655 - 1680 16
1800 2045 1970 39 44 M36 1829.0 - 88 69 84 - - - - - 1746 - 133 20 - - - 1855 - 1878 16
2000 2265 2180 42 48 M39 2032.0 - 96 74 92 - - - - - 1950 - 146 25 - - - 2058 - 2082 16
2200 2475 2390 42 52 M39 2035.0 - - - 81 - - - - - - - - 154 25 - - - 2260 - - 18
2400 2685 2600 42 56 M39 2438.0 - - - 87 - - - - - - - - 168 25 - - - 2462 - - 18
2600 2905 2710 48 60 M45 2620.0 - - - 91 - - - - - - - - 175 25 - - - 2665 - - 18
2800 3115 3020 48 64 M45 2820.0 - - - 101 - - - - - - - - 188 30 - - - 2865 - - 18
3000 3315 3220 48 68 M45 3020.0 - - - 102 - - - - - - - - 192 30 - - - 3068 - - 18
3200 3525 3430 48 72 M45 3220.0 - - - 106 - - - - - - - - 202 30 - - - 3272 - - 20
3400 3735 3640 48 76 M45 3420.0 - - - 110 - - - - - - - - 214 35 - - - 3475 - - 20
3600 3970 3860 56 80 M52 3620.0 - - - 124 - - - - - - - - 229 35 - - - 3678 - - 20
* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
** To be specified by the purchaser.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1"
Note 4: Type 33; lapped pipe end without determination of thickness and height.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN10 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 21 (Integral flanges)

02 (Loose plate flanges with weld-on plate collar) 32 (Weld-on plate collars)
33 (Lapped pipe ends without determination of
04 (Loose plate flanges with weld-neck collar)
thickness and height)

05 (Blank [blind] flanges) 35 (Weld-neck collars)

11 (Weld-neck flanges) 36 (Pressed collar with long neck)

12 (Hubbed slip-on flanges for welding) 37 (Pressed collar)

13 (Hubbed threaded flanges)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN10 Flanges
Mating dimensions

Corner Radius

Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter

Chamfer
Outside

Outside

Neck

Bore Flange Neck

Bolting Diameter thickness Collar thickness Length diameters
DN G
D K L No Size A B1 B2 B3 C1 C2 C3 C4 E F max H1 H2 H3 H4 H5 N1 N2 N3 R1 S
Flange type
11
11 12 11
21*** 01 01 11 13 35
34* 12 02 12 02 32 12 11 11 11 12 21 36
01, 02, 04, 05, 11, 12, 13, 21 35-37 32 02 04 04 13 21 05 04 34 35 36 37 05 13 34* 34* 35 36 37 34* 13 21 34 34 37
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3 12 5 2.0 2.5 - 22 35 6 35 35 7 28 30 28 4 1.8
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3 12 5 2.0 2.5 - 22 38 6 38 38 7 32 35 32 4 2.0
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4 14 6 2.5 3.0 - 26 40 6 40 40 8 40 45 40 4 2.3
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4 14 7 2.5 3.0 - 28 40 6 40 40 10 46 52 50 4 2.6
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5 14 8 3.0 3.0 - 30 42 6 42 42 12 56 60 60 6 2.6
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5 14 8 3.0 3.0 - 32 45 7 45 45 15 64 70 70 6 2.6
50 165 125 18 4 M16 60.3 61.5 65 77 20 18 18 18 5 16 8 3.0 4.0 - 28 45 8 45 45 20 74 84 84 6 2.9
65 185 145 18 8 M16 76.1 77.5 81 96 20 18 18 18 6 16 8 3.0 4.0 55 32 45 10 45 45 20 92 104 104 6 2.9
80 200 160 18 8 M16 88.9 90.5 94 108 20 20 20 20 6 16 10 3.0 4.0 70 34 50 10 50 50 25 105 118 120 6 3.2
100 220 180 18 8 M16 114.3 116.0 120 134 22 20 20 20 6 18 10 4.0 4.0 90 40 52 12 52 52 25 131 140 140 8 3.6
125 250 210 18 8 M16 139.7 141.5 145 162 22 22 22 22 6 18 10 4.0 4.0 115 44 55 12 55 55 25 156 168 170 8 4.0

See “Wall thickness and end preparation”

150 285 240 22 8 M20 168.3 170.5 174 188 24 22 22 22 6 20 10 4.0 4.0 140 44 55 12 55 55 25 184 195 190 10 4.5
200 340 295 22 8 M20 219.1 221.5 226 240 24 24 24 24 6 20 11 5.0 5.0 190 44 62 16 62 62 30 234 246 246 10 6.3
250 395 350 22 12 M20 273.0 276.5 281 294 26 26 26 26 8 22 12 8.0 - 235 46 68 16 68 68 - 292 298 298 12 6.3
300 445 400 22 12 M20 323.9 327.5 333 348 26 26 26 26 8 22 12 8.0 - 285 46 68 16 68 68 - 342 350 348 12 7.1
350 505 460 22 16 M20 355.6 359.5 365 400 30 26 26 26 8 22 13 8.0 - 330 53 68 16 68 68 - 385 400 408 12 7.1
400 565 515 26 16 M24 406.4 411.0 416 450 32 26 26 26 8 24 14 8.0 - 380 57 72 16 72 72 - 440 456 456 12 7.1
450 615 565 26 20 M24 457.0 462.0 467 498 36 28 28 28 8 24 15 - - 425 63 72 16 72 - - 488 502 502 12 7.1
500 670 620 26 20 M24 508.0 513.5 519 550 38 28 28 28 8 26 16 - - 475 67 75 16 75 - - 542 559 559 12 7.1
600 780 725 30 20 M27 610.0 616.5 622 650 42 30 34 34 8 26 18 - - 575 75 82 18 80 - - 642 658 658 12 -
700 895 840 30 24 M27 711.0 721 - 50 35 38 8 - 20 - - 670 - 85 18 80 - - 746 - 772 12 -
800 1015 950 33 24 M30 813.0 824 - 56 38 48 8 - 20 - - 770 - 96 18 90 - - 850 - 876 12 -
900 1115 1050 33 28 M30 914.0 ** 926 - 62 38 50 8 - 22 - - 860 - 99 20 95 - - 950 - 976 12 -
1000 1230 1160 36 28 M33 1016 1028 - 70 44 54 8 - 24 - - 960 - 105 20 95 - - 1052 - 1080 16 -
**
1200 1455 1380 39 32 M36 1219 1234 - 83 55 66 8 - 26 - - 1160 - 132 25 115 - - 1256 - 1292 16 -
1400 1675 1590 42 36 M39 1422 - - - 65 - - - - - - - - 143 25 - - - 1460 - 1496 16 -
1600 1915 1820 48 40 M45 1626 - - - 75 - - - - - - - - 159 25 - - - 1666 - 1712 16 -
1800 2115 2020 48 44 M45 1829 - - - 85 - - - - - - - - 175 30 - - - 1868 - 1910 16 -
2000 2325 2230 48 48 M45 2032 - - - 90 - - - - - - - - - 186 30 - - - 2072 - 2120 16 -
2200 2550 2440 56 52 M52 2235 - - ** 100 - - - - - - - - - 202 35 - - - 2275 - - 18 -
2400 2760 2650 56 56 M52 2438 - - - 110 - - - - - - - - - 218 35 - - - 2478 - - 18 -
2600 2960 2850 56 60 M52 2620 - - - 110 - - - - - - - - - 224 40 - - - 2680 - - 18 -
2800 3180 3070 56 64 M52 2820 - - - 124 - - - - - - - - - 244 40 - - - 2882 - - 18 -
3000 3405 3290 62 68 M56 3020 - - 132 - - - - - - - - - 257 45 - - - 3085 - - 18 -
* Use is limited up to DN600.
** To be specified by the purchaser.
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".
Note 4: Type 33; lapped pipe end without determination of thickness and height.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN16 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 21 (Integral flanges)

02 (Loose plate flanges with weld-on plate collar) 32 (Weld-on plate collars)
33 (Lapped pipe ends without determination of
04 (Loose plate flanges with weld-neck collar)
thickness and height)

05 (Blank [blind] flanges) 34 (Weld-neck collars)

11 (Weld-neck flanges) 35 (Weldring neck)

12 (Hubbed slip-on flanges for welding) 36 (Pressed collar with long neck)

13 (Hubbed threaded flanges) 37 (Pressed collar)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN16 Flanges
Mating dimensions

Corner Radius

Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter

Chamfer
Outside

Outside

Neck

Bore Flange Neck

Bolting Diameter thickness Collar thickness Length diameters
DN G
D K L No Size A B1 B2 B3 C1 C2 C3 C4 E F max H1 H2 H3 H4 H5 N1 N2 N3 R1 S
Flange type
11
11 12 11
21*** 01 01 11 13 35
34* 12 02 12 02 32 12 11 11 11 12 21 36
01, 02, 04, 05, 11, 12, 13, 21 35-37 32 02 04 04 13 21 05 04 34 35 36 37 05 13 34** 34** 35 36 37 34** 13 21 34 34 37
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3 12 5 2.0 2.5 - 22 35 6 35 35 7 28 30 28 4 1.8
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3 12 5 2.0 2.5 - 22 38 6 38 38 7 32 35 32 4 2.0
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4 14 6 2.5 3.0 - 26 40 6 40 40 8 40 45 40 4 2.3
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4 14 7 2.5 3.0 - 28 40 6 40 40 10 46 52 50 4 2.6
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5 14 8 3.0 3.0 - 30 42 6 42 42 12 56 60 60 6 2.6
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5 14 8 3.0 3.0 - 32 45 7 45 45 15 64 70 70 6 2.6
50 165 125 18 4 M16 60.3 61.5 65 77 20 18 18 18 5 16 8 3.0 4.0 - 28 45 8 45 45 20 74 84 84 6 2.9
65 185 145 18 8 a M16 76.1 77.5 81 96 20 18 18 18 6 16 8 3.0 4.0 55 32 45 10 45 45 20 92 104 104 6 2.9
80 200 160 18 8 M16 88.9 90.5 94 108 20 20 20 20 6 16 10 3.0 4.0 70 34 50 10 50 50 25 105 118 120 6 3.2

See “Wall thickness and end preparation”

100 220 180 18 8 M16 114.3 116.0 120 134 22 20 20 20 6 18 10 4.0 4.0 90 40 52 12 52 52 25 131 140 140 8 3.6
125 250 210 18 8 M16 139.7 141.5 145 162 22 22 22 22 6 18 10 4.0 4.0 115 44 55 12 55 55 25 156 168 170 8 4.0
150 285 240 22 8 M20 168.3 170.5 174 188 24 22 22 22 6 20 10 5.0 5.0 140 44 55 12 55 55 25 184 195 190 10 4.5
200 340 295 22 12 M20 219.1 221.5 226 240 26 24 24 24 6 20 11 6.0 6.0 190 44 62 16 62 62 30 235 246 246 10 6.3
250 405 355 26 12 M24 273.0 276.5 281 294 29 26 26 26 8 22 12 10.0 - 235 46 70 16 70 68 - 292 298 296 12 6.3
300 460 410 26 12 M24 323.9 327.5 333 348 32 28 28 28 8 24 14 10.0 - 285 46 78 16 78 68 - 344 350 350 12 7.1
350 520 470 26 16 M24 355.6 359.5 365 400 35 30 30 30 8 26 18 10.0 - 330 57 82 16 82 68 - 390 400 410 12 8.0
400 580 525 30 16 M27 406.4 411.0 416 454 38 32 32 32 8 28 20 10.0 - 380 63 85 16 85 72 - 445 456 458 12 8.0
450 640 585 30 20 M27 457.0 462.0 467 500 42 34 40 40 8 30 22 - - 425 68 83 16 87 - - 490 502 516 12 8.0
500 715 650 33 20 M30 508.0 513.5 519 556 46 36 44 44 8 32 22 - - 475 73 84 16 90 - - 548 559 576 12 8.0
600 840 770 36 20 M33 610.0 616.5 622 660 55 40 54 54 8 32 24 - - 575 83 88 18 95 - - 670 658 690 12 8.8
700 910 840 36 24 M33 711.0 721 - 63 40 58 8 - 26 - - 670 83 104 18 100 - - 755 760 760 12 -
800 1025 950 39 24 M36 813.0 824 - 74 41 62 8 - 28 - - 770 90 108 20 105 - - 855 864 862 12 -
**
900 1125 1050 39 28 M36 914.0 926 - 82 48 64 8 - 30 - - 860 94 118 20 110 - - 955 968 962 12 -
1000 1255 1170 42 28 M39 1016 1030 - 90 59 68 8 - 35 - - 960 100 137 22 120 - - 1058 1072 1076 16 -
1200 1485 1390 48 32 M45 1219 - - - 78 ** - - - - - - 1160 - 160 30 - - - 1262 - 1282 16 -
1400 1685 1590 48 36 M45 1422 - - - 84 - - - - - - 1346 - 177 30 - - - 1465 - 1482 16 -
1600 1930 1820 56 40 M52 1626 - - - ** 102 - - - - - - 1546 - 204 35 - - - 1668 - 1696 16 -
1800 2130 2020 56 44 M52 1829 - - - 110 - - - - - - 1746 - 218 35 - - - 1870 - 1896 16 -
2000 2345 2230 62 48 M56 2032 - - - 124 - - - - - - 1950 - 238 40 - - - 2072 - 2100 16 -
⒜According to EN 1092-2 (Cast Iron Flanges) and EN1092-3 (Copper Alloy Flanges), the flanges in this DN and PN may be supplied with 4
holes. Where steel flanges are required with 4 holes, these may be supplied by agreement between flange manufacturer and purchaser.
* Use is limited up to DN600.
** To be specified by the purchaser.
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".
Note 4: Type 33; lapped pipe end without determination of thickness and height.

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN25 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges)

02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)

04 (Loose plate flanges with weld-neck collar) 32 (Weld-on plate collars)

05 (Blank [blind] flanges) 34 (Weld-neck collars)

11 (Weld-neck flanges) 35 (Weldring neck)

12 (Hubbed slip-on flanges for welding)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN25 Flanges
Mating dimensions

Corner Radius

Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter

Chamfer
Outside

Outside

Collar
Neck
Bore Flange thicknes Neck
Bolting Diameter thickness s Length diameters
DN G
D K L No Size A B1 B2 B3 C1 C2 C3 C4 E F max H1 H2 H3 H4 N1 N2 N3 R1 S
Flange type
11
11 12
21*** 01 01 11 13
34* 12 02 12 02 32 12 11 11 11 12 21 11
01, 02, 04, 05, 11, 12, 13, 21 35 32 02 04 04 13 21 05 04 34 35 05 13 34* 34* 35 34 13 21 34 34 35
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3 12 5 - 22 35 6 35 28 30 28 4 1.8
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3 12 5 - 22 38 6 38 32 35 32 4 2.0
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4 14 6 - 26 40 6 40 40 45 40 4 2.3
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4 14 7 - 28 40 6 40 46 52 50 4 2.6
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5 14 8 - 30 42 6 42 56 60 60 6 2.6
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5 14 8 - 32 45 7 45 64 70 70 6 2.6
50 165 125 18 4 M16 60.3 61.5 65 77 20 20 20 20 5 16 10 - 34 48 8 48 75 84 84 6 2.9
65 185 145 18 8 M16 76.1 77.5 81 96 22 22 22 22 6 16 11 55 38 52 10 52 90 104 104 6 2.9
80 200 160 18 8 M16 88.9 90.5 94 114 24 24 24 24 6 18 12 70 40 58 12 58 105 118 120 8 3.2

See t “Wall thickness and end preparation”

100 235 190 22 8 M20 114.3 116.0 120 138 26 24 24 24 6 20 14 90 44 65 12 65 134 145 142 8 3.6
125 270 220 26 8 M24 139.7 141.5 145 166 28 26 26 26 6 22 16 115 48 68 12 68 162 170 162 8 4.0
150 300 250 26 8 M24 168.3 170.5 174 194 30 28 28 28 6 24 18 140 52 75 12 75 192 200 192 10 4.5
200 360 310 26 12 M24 219.1 221.5 226 250 32 30 30 30 6 26 18 190 52 80 16 80 244 256 252 10 6.3
250 425 370 30 12 M27 273.0 276.5 281 302 35 32 32 32 8 26 18 235 60 88 18 88 298 310 304 12 7.1
300 485 430 30 16 M27 323.9 327.5 333 356 38 34 34 34 8 28 20 285 67 92 18 92 352 364 364 12 8.0
350 555 490 33 16 M30 355.6 359.5 365 408 42 38 38 38 8 32 22 332 72 100 20 100 398 418 418 12 8.0
400 620 550 36 16 M33 406.4 411.0 416 462 48 40 40 40 8 34 24 380 78 110 20 110 452 472 472 12 8.8
450 670 600 36 20 M33 457.0 462.0 467 510 54 46 46 50 8 36 26 425 84 110 20 110 500 520 520 12 8.8
500 730 660 36 20 M33 508.0 513.5 519 568 58 48 48 51 8 38 28 475 90 125 20 125 558 580 580 12 10
600 840 770 39 20 M36 610.0 616.5 622 670 68 48 58 66 8 40 30 575 100 125 20 115 660 684 684 12 11
700 960 875 42 24 M39 711.0 721 - 85 50 8 - 30 - - 129 20 125 760 - 780 12 -
800 1085 990 48 24 M45 813.0 ** 824 - 95 53 8 - 35 - - 138 22 135 864 - 882 12 -
** **
900 1185 1090 48 28 M45 914.0 - - 57 - - - - - 148 24 - 968 - 982 12 -
**
1000 1320 1210 56 28 M52 1016 - - - 63 - - - - - 160 24 - 1070 - 1086 16 -
1200 1530 1420 56 32 M52 1219
1400 1755 1640 62 36 M56 1422
1600 1975 1860 62 40 M56 1626 To be specified by the purchaser
1800 2195 2070 70 44 M64 1829
2000 2425 2300 70 48 M64 2032
* Use is limited up to DN500.
** To be specified by the purchaser.
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN40 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges)

02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)

04 (Loose plate flanges with weld-neck collar) 32 (Weld-on plate collars)

05 (Blank [blind] flanges) 34 (Weld-neck collars)

11 (Weld-neck flanges) 35 (Weldring neck)

12 (Hubbed slip-on flanges for welding)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN40 Flanges
Mating dimensions

Corner Radius

Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter

Chamfer
Outside

Outside

Collar
Neck
Bore Flange thicknes Neck
Bolting Diameter thickness s Length diameters
DN G
D K L No Size A B1 B2 B3 C1 C2 C3 C4 E F max H1 H2 H3 H4 N1 N2 N3 R1 S
Flange type
11
11 01 01 11 12
21*** 12 02 12 02 32 12 11 11 11 12 13 11
01, 02, 04, 05, 11, 12, 13, 21 34* 32 02 04 04 13 21 05 04 34* 35 05 13 34* 34* 35 34 13 21 21 34* 35
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3 12 5 - 22 35 6 35 28 30 28 4 1.8
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3 12 5 - 22 38 6 38 32 35 32 4 2.0
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4 14 6 - 26 40 6 40 40 45 40 4 2.3
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4 14 7 - 28 40 6 40 46 52 50 4 2.6
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5 14 8 - 30 42 6 42 56 60 60 6 2.6
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5 14 8 - 32 45 7 45 64 70 70 6 2.6
50 165 125 18 4 M16 60.3 61.5 65 77 20 20 20 20 5 16 10 - 34 48 8 48 75 84 84 6 2.9
65 185 145 18 8 M16 76.1 77.5 81 96 22 22 22 22 6 16 11 55 38 52 10 52 90 104 104 6 2.9
80 200 160 18 8 M16 88.9 90.5 94 114 24 24 24 24 6 18 12 70 40 58 12 58 105 118 120 8 3.2

See “Wall thickness and end preparation”

100 235 190 22 8 M20 114.3 116.0 120 138 26 24 24 24 6 20 14 90 44 65 12 65 134 145 142 8 3.6
125 270 220 26 8 M24 139.7 141.5 145 166 28 26 26 26 6 22 16 115 48 68 12 68 162 170 162 8 4.0
150 300 250 26 8 M24 168.3 170.5 174 194 30 28 28 28 6 24 18 140 52 75 12 75 192 200 192 10 4.5
200 375 320 30 12 M27 219.1 221.5 226 250 36 34 34 36 6 28 20 190 52 88 16 88 244 260 254 10 6.3
250 450 385 33 12 M30 273.0 276.5 281 312 42 38 38 38 8 30 22 235 60 105 18 105 306 312 312 12 7.1
300 515 450 33 16 M30 323.9 327.5 333 368 52 42 42 42 8 34 25 285 67 115 18 115 362 380 376 12 8.0
350 580 510 36 16 M33 355.6 359.5 365 418 58 46 46 46 8 32 28 330 72 125 20 125 408 424 432 12 8.8
400 660 585 39 16 M36 406.4 411.0 416 472 65 50 50 50 8 42 32 380 78 135 20 135 462 478 498 12 11.0
450 685 610 39 20 M36 457.0 462.0 467 510 57 57 57 8 46 - 425 84 135 20 - 500 522 522 12 12.5
500 755 670 42 20 M39 508.0 513.5 519 572 ** 57 57 57 8 50 - 475 90 140 20 - 562 576 576 12 14.2
600 890 795 48 20 M45 610.0 616.5 622 676 72 72 72 8 40 - 575 100 150 20 - 666 686 686 12 16.0
700 995 900 48 24 M45
800 1140 1030 56 24 M52
900 1250 1140 56 28 M52
1000 1360 1250 56 28 M52
1200 1575 1460 62 32 M56 To be specified by the purchaser
1400 1795 1680 62 36 M56
1600 2025 1900 70 40 M64
1800 2195 2070 70 44 M64
2000 2425 2300 70 48 M64
* Use is limited up to DN600.
** To be specified by the purchaser.
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN63 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 12 (Hubbed slip-on flanges for welding)

05 (Blank [blind] flanges) 13 (Hubbed threaded flanges)

11 (Weld-neck flanges) 21 (Integral flanges)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN63 Flanges
Mating dimensions

Corner Radius

Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter
Outside

Outside

Neck
Bore Flange Neck
Bolting Diameter thickness Length diameters
DN G
D K L No Size A B1 C1 C2 C3 C4 max H1 H2 H3 N1 N2 N3 R1 S
Flange type
11
11 12
11 01 12 12 12 13
01, 05, 11, 12, 13, 21 21*** 12 01 13 21 05 05 13 11 11 11 13 21 21 11
10 100 70 14 4 M12 17.2 18.0 20 20 20 20 - 28 45 6 32 40 40 4
15 105 75 14 4 M12 21.3 22.0 20 20 20 20 - 28 45 6 34 43 45 4
20 130 90 18 4 M16 26.9 27.5 22 22 22 22 - 30 48 8 42 52 50 4
25 140 100 18 4 M16 33.7 34.5 24 24 24 24 - 32 58 8 52 60 61 4
32 155 110 22 4 M20 42.4 43.5 24 24 26 24 - 32 60 8 62 68 68 6
40 170 125 22 4 M20 48.3 49.5 26 26 26 26 - 34 62 10 70 80 82 6
50 180 135 22 4 M20 60.3 61.5 26 26 26 26 - 36 62 10 82 90 90 6

See “Wall thickness and end preparation”

65 205 160 22 8 M20 76.1 77.5 26 26 26 26 45 40 68 12 98 112 105 6
80 215 170 22 8 M20 88.9 90.5 30 28 28 28 60 44 72 12 112 125 122 8
100 250 200 26 8 M24 114.3 116.0 32 30 30 30 80 52 78 12 138 152 146 8
125 295 240 30 8 M27 139.7 141.5 34 34 34 34 105 56 88 12 168 185 177 8
150 345 280 33 8 M30 168.3 170.5 36 36 36 36 130 60 95 12 202 215 204 10
200 415 345 36 12 M33 219.1 221.5 48 42 42 42 180 - 110 16 256 - 264 10
250 470 400 36 12 M33 273.0 276.5 55 46 46 46 220 - 125 18 316 - 320 12
300 530 460 36 16 M33 323.9 327.5 65 52 52 52 270 - 140 18 372 - 378 12
350 600 525 39 16 M36 355.6 359.5 72 56 56 56 310 - 150 20 420 - 434 12
400 670 585 42 16 M39 406.4 411.0 80 60 60 60 360 - 160 20 475 - 490 12
500 800 705 48 20 M45
600 930 820 56 20 M52
700 1045 935 56 24 M52
800 1165 1050 62 24 M56 To be specified by the purchaser
900 1285 1170 62 28 M56
1000 1415 1290 70 28 M64
1200 1665 1530 78 32 M72x6
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN100 Flanges

Flange type (typ) as in EN 1092-1

01 (Plate [slip-on] flanges for welding) 12 (Hubbed slip-on flanges for welding)

05 (Blank [blind] flanges) 13 (Hubbed threaded flanges)

11 (Weld-neck flanges) 21 (Integral flanges)

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN100 Flanges
Mating dimensions

Corner Radius

Wall thickness
Diameter of

Diameter of

Diameter of

Diameter of
Bolt Circle

Shoulders
Bolt Hole
Diameter
Outside

Outside

Neck
Bore Flange Neck
Bolting Diameter thickness Length diameters
DN G
D K L No Size A B1 C1 C2 C3 C4 max H1 H2 H3 N1 N2 N3 R1 S
Flange type
11
11 12
11 01 12 12 12 13
01, 05, 11, 12, 13, 21 21*** 12 01 13 21 05 05 13 11 11 11 13 21 21 11
10 100 70 14 4 M12 17.2 18.0 20 20 20 20 - 28 45 6 32 40 40 4
15 105 75 14 4 M12 21.3 22.0 20 20 20 20 - 28 45 6 34 43 45 4
20 130 90 18 4 M16 26.9 27.5 22 22 22 22 - 30 48 8 42 52 50 4
25 140 100 18 4 M16 33.7 34.5 24 24 24 24 - 32 58 8 52 60 61 4

See “Wall thickness and end preparation”

32 155 110 22 4 M20 42.4 43.5 24 24 26 24 - 32 60 8 62 68 68 6
40 170 125 22 4 M20 48.3 49.5 26 26 28 26 - 34 62 10 70 80 82 6
50 195 145 26 4 M24 60.3 61.5 28 28 30 30 - 36 68 10 90 95 96 6
65 220 170 26 8 M24 76.1 77.5 30 30 34 30 45 40 76 12 108 118 118 6
80 230 180 26 8 M24 88.9 90.5 34 32 36 32 60 44 78 12 120 130 128 8
100 265 210 30 8 M27 114.3 116.0 36 36 40 36 80 52 90 12 150 158 150 8
125 315 250 33 8 M30 139.7 141.5 42 40 40 40 105 56 105 12 180 188 185 8
150 355 290 33 12 M30 168.3 170.5 48 44 44 44 130 60 115 12 210 225 216 10
200 430 360 36 12 M33 219.1 221.5 60 52 52 52 180 - 130 16 278 - 278 10
250 505 430 39 12 M36 273.0 276.5 72 60 60 60 210 - 157 18 340 - 340 12
300 585 500 42 16 M39 323.9 327.5 84 68 68 68 260 - 170 18 400 - 407 12
350 655 560 48 16 M45 355.6 359.5 95 74 74 74 300 - 189 20 460 - 460 12
400 715 620 48 16 M45 406.4 411.0 80 60 60 60 360 - 160 20 475 - 490 12
500 870 760 56 20 M52 508.0 513.5 To be specified by the purchaser
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1, N2 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2:The centre portion of the face of a flange type 05 need not be machined provided that the diameter of the un-machined portion does
not exceed the recommended diameter for G max.
Note 3: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN160 Flanges

Flange type (typ) as in EN 1092-1

11 (Weld-neck flanges) 21 (Integral flanges)

Mating dimensions

Wall thickness
Diameter of

Diameter of

Diameter of
Bolt Circle

Bolt Hole
Diameter
Outside

Outside

Neck

Flange Neck Corner

DN Bolting thickness Length diameters Radius

D K L No Size A C2 C3 H2 H3 N1 N3 R1 S
Flange type

11
11, 21 21*** 11 21 11 11 11 21 11 21 11
10 100 70 14 4 M12 17.2 20 20 45 6 32 40 4 4 2.0
15 105 75 14 4 M12 21.3 20 20 45 6 34 45 4 4 2.0
25 140 100 18 4 M16 33.7 24 24 58 8 52 61 4 4 2.9
40 170 125 22 4 M20 48.3 28 28 64 10 70 82 6 4 3.6
50 195 145 26 4 M24 60.3 30 30 75 10 90 96 6 4 4.0
65 220 170 26 8 M24 76.1 34 34 82 12 108 118 6 5 5.0
80 230 180 26 8 M24 88.9 36 36 86 12 120 128 8 5 6.3
100 265 210 30 8 M27 114.3 40 40 100 12 150 150 8 5 8.0
125 315 250 33 8 M30 139.7 44 44 115 14 180 184 8 6 10.0
150 355 290 33 12 M30 168.3 50 50 128 14 210 224 10 6 12.5
200 430 360 36 12 M33 219.1 60 60 140 16 278 288 10 8 16.0
250 515 430 42 12 M39 273.0 68 68 155 18 340 346 12 8 20.0
300 585 500 42 16 M39 323.9 78 78 175 18 400 414 12 10 22.2
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN250 Flanges

Flange type (typ) as in EN 1092-1

11 (Weld-neck flanges) 21 (Integral flanges)

Mating dimensions

Wall thickness
Diameter of

Diameter of

Diameter of
Bolt Circle

Bolt Hole
Diameter
Outside

Outside

Neck

Flange Neck Corner

DN Bolting thickness Length diameters Radius

D K L No Size A C2 C3 H2 H3 N1 N3 R1 S
Flange type

11
11, 21 21*** 11 21 11 11 11 21 11 21 11
10*** 125 85 18 4 M16 - - 24 - - - 46 - 4 -
15 130 90 18 4 M16 21.3 26 26 60 6 48 52 4 4 2.6
25 150 105 22 4 M20 33.7 28 28 65 8 60 63 4 4 3.6
40 185 135 26 4 M24 48.3 34 34 80 10 84 90 6 4 5.0
50 200 150 26 8 M24 60.3 38 38 85 10 95 102 6 5 6.3
65 230 180 26 8 M24 76.1 42 42 95 12 124 125 6 5 8.0
80 255 200 30 8 M27 101.6 46 46 102 12 136 142 8 6 11.0
100 300 235 33 8 M30 127.0 54 54 120 14 164 168 8 6 14.2
125 340 275 33 12 M30 152.4 60 60 140 16 200 207 8 6 16.0
150 390 320 36 12 M33 177.8 68 68 160 18 240 246 10 8 17.5
200 485 400 42 12 M39 244.5 82 82 190 25 305 314 10 8 25.0
250 585 490 48 16 M45 298.5 100 100 215 30 385 394 12 10 32.0
300* 690 590 52 16 M48 - - 120 - - - 480 - 10 -
* For flange type 21.
** For flange type 11 use flanges PN320.
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN320 Flanges

Flange type (typ) as in EN 1092-1

11 (Weld-neck flanges) 21 (Integral flanges)

Mating dimensions

Wall thickness
Diameter of

Diameter of

Diameter of
Bolt Circle

Bolt Hole
Diameter
Outside

Outside

Neck

Flange Neck Corner

DN Bolting thickness Length diameters Radius

D K L No Size A C2 C3 H2 H3 N1 N3 R1 S
Flange type

11
11, 21 21*** 11 21 11 11 11 21 11 21 11
10 125 85 18 4 M16 17.2 24 24 58 6 44 46 4 4 2.6
15 130 90 18 4 M16 21.3 26 26 60 6 48 52 4 4 3.2
25 160 115 22 4 M20 33.7 34 34 78 8 68 72 4 4 5.0
40 195 145 26 4 M24 48.3 38 38 88 10 92 96 6 5 6.3
50 210 160 26 8 M24 63.5 42 42 100 10 106 110 6 5 8.0
65 255 200 30 8 M27 88.9 51 51 120 12 138 137 6 6 11.0
80 275 220 30 8 M27 101.6 55 55 130 14 156 160 8 6 12.5
100 335 265 36 8 M33 133.0 65 65 145 16 186 190 8 8 16.0
125 380 310 36 12 M33 168.3 75 75 175 20 230 235 8 8 20.0
150 425 350 39 12 M36 193.7 84 84 195 25 265 266 10 10 25.0
200 525 440 42 16 M39 244.5 103 103 235 30 345 350 10 10 30.0
250 640 540 52 16 M48 323.9 125 125 300 40 428 432 12 10 40.0
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578

 EN 1092-1 PN400 Flanges

Flange type (typ) as in EN 1092-1

11 (Weld-neck flanges) 21 (Integral flanges)

Mating dimensions

Wall thickness
Diameter of

Diameter of

Diameter of
Bolt Circle

Bolt Hole
Diameter
Outside

Outside

Neck

Flange Neck Corner

DN Bolting thickness Length diameters Radius

D K L No Size A C2 C3 H2 H3 N1 N3 R1 S
Flange type

11
11, 21 21*** 11 21 11 11 11 21 11 21 11
10 125 85 18 4 M16 17.2 28 28 65 8 48 48 4 4 3.6
15 145 100 22 4 M20 26.9 30 30 68 8 56 57 4 4 5.0
25 180 130 26 4 M24 42.4 38 38 90 10 82 81 4 5 7.1
40 220 165 30 4 M27 60.3 48 48 110 12 106 105 6 5 10.0
50 235 180 30 8 M27 76.1 52 52 120 15 120 120 6 6 12.5
65 290 225 33 8 M30 101.6 64 64 135 18 158 158 6 6 16.0
80 305 240 33 8 M30 114.3 68 68 150 20 174 174 8 8 17.5
100 370 295 39 8 M36 139.7 80 80 175 25 216 216 8 8 22.2
125 415 340 39 12 M36 193.7 92 92 200 30 258 259 8 10 30.0
150 475 390 42 12 M39 219.1 105 105 225 35 302 302 10 10 35.0
200 585 490 48 16 M45 273.0 130 130 280 40 388 388 10 10 40.0
*** For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note 1: Dimensions N1 and N3 are measured at the intersection of the hub draft angle and the back face of the flange.
Note 2: For d1 dimensions see document "Flange Facing Dimensions EN 1092-1".

Website: www.pipefittingweb.com Email: wellgrow@pipefittingweb.com Fax: 886-423112578