Product description Important instructions for assembly and Synchronisation mode.

y and Synchronisation mode. (To use synchronised mode all sensors ■ Measurement range set to maximum ran-
■ The mic+sensor with one switched outpus application If the assembly distances shown in Fig.1 for must be set to address »00«.) ge
measures the distance to an object within All employee and plant safety-relevant two or more sensors are exceeded the inte-
the detection zone contactless. Depen- measures must be taken prior to assembly, grated synchronisation should be used. Con- Assembly instructions Set the parameters of the sensor manually or
ding on the adjusted detect distance the start-up, or maintenance work (see operation nect Sync/Com-channels (pin 5 at the units re- ☞ Assemble the sensor at the installation lo- use the Teach-in procedure to adjust the de-
switched output is set. manual for the entire plant and the operator ceptable) of all sensors (10 maximum). cation. tect points.
■ All settings are done with two push-but- instruction of the plant). ☞ Plug in the connector cable to the M 12
tons and a three-digit LED-display A B connector.
The sensors are not considered as safety measuring range
(TouchControl). cm mm %
equipment and may not be used to ensure <10 cm <1,0 m 3-digit
■ Light emitting diodes (three-colour LEDs)
human or machine safety! <30 cm <1,7 m LED-display
indicate the switching status. 2 1
■ The output functions are changeable <60 cm <5,4 m 3 5 4 LED D1 and D2
The mic+ sensors indicate a blind zone, in
from NOC to NCC. <1,6 m <16 m colour
which the distance cannot be measured. The
■ The sensors are adjustable manually using <2,6 m <30 m 1 +UB brown Push-buttons T1 and T2
operating range indicates the distance of the T1 D1 D2 T2
the numerical LED-display or may be trai- sensor that can be applied with normal re- 3 -UB blue
ned using Teach-in processes. 4 D black
flectors with sufficient function reserve. 2 - white
■ Useful additional functions are set in the When using good reflectors, such as a calm Fig. 1: Assembly distances, indicating syn- 5 Sync/Com. grey Fig. 3: TouchControl
Add-on-menu. chronisation/multiplex
Instruction manual ■ Using the LinkControl adapter (optional
water surface, the sensor can also be used up
Operation
to its maximum range. Objects that strongly
mic+ Ultrasonic Sensors with accessory) all TouchControl and additio- absorb (e.g. plastic foam) or diffusely reflect Multiplex mode Fig. 2: Pin assignment with view onto sensor mic+sensors work maintenance free. Small
two switched outputs nal sensor parameter settings may be sound (e.g. pebble stones) can also reduce The Add-on-menu allows to assign an indivi- plug and colour coding of the amounts of dirt on the surface do not influ-
made by a Windows-Software. the defined operating range. dual address »01« to »10« to each sensor microsonic connection cable ence function. Thick layers of dirt and caked-
mic+25/D/TC mic+25/E/TC connected via the Sync/Com-channel (Pin5). on dirt affect sensor function and therefore
The sensors perform the ultrasonic measure- Start-up must be removed.
mic+35/D/TC mic+35/E/TC
ment sequentially from low to high address. mic+ sensors are delivered factory made with
mic+130/D/TC mic+130/E/TC Therefore any influence between the sensors the following settings: Note
mic+340/D/TC mic+340E/TC is rejected. ■ Switched output on NOC
The address »00« is reserved to synchronisa- ■ Detecting distance at operating range ■ mic+sensors have internal temperature
mic+600/D/TC mic+600/E/TC tion mode and deactivates the multiplex and half operating range compensation. Because the sensors heat
up on their own, the temperature com-
pensation reaches its optimum working
point after approx. 30 minutes of operati-
Start here on.
T1 + T2
 ■ During normal mode operation, a yellow
LED D2 signals that the switched output
Press T1 and T2 simultaneously for about
3 s until welcome message has passed has connected.

■ During normal mode operation, the mea-

sured distance value is displayed on the
LED-indicator in mm (up to 999 mm) or
 T1 T2  cm (from 100 cm). Scale switches auto-
matically and is indicated by a point on
T1 + T2 top of the digits.

T1
T2 Set detect distance in ■ During Teach-in mode, the hysteresis
mm or cm loops are set back to factory settings.

1 T1 + T2 1 2
■ If no objects are placed within the detec-
 tion zone the LED-indicator shows »- - -«.

 For single detect

point press T2  For window mode
operation set far ■ If no push-buttons are pressed for 20 se-
T2 until »- - -« is T1 T2 detect point in conds during parameter setting mode the
displayed  mm or cm made changes are stored and the sensor
returns to normal mode operation.
T1 + T2
 ■ You can lock the key pad to provide in-
 Choose » « for NCC or puts, see »Key lock and factory setting«.
T1 T2
» « for NOC
 ■ You can reset the factory settings at any
time, see »Key lock and factory setting«.
T1 + T2

Set switched output Show parameters

 Tapping push-button T1 shortly during nor-
mal mode operation shows »PAr« on the
LED-display. Each time you tap push-button
 T2 T1  T1 the actual settings of the switched output
are shown.
T1 + T2

Set sensor parameters alternatively 

Ready
numerically using LED-display...
89/336/EEC
...or with the Teach-in procedure Key lock and factory setting

1
Activate/deactivate Reset to factory set-
1 1 2
TouchControl ting

Turn supply voltage Turn supply voltage

OFF OFF
Adjust two-way reflectiv
Adjust detect point Adjust window mode Set NOC/NCC
barrier

While pressing T1 turn While pressing T1 turn

Place object at position ➀ Place object at position ➀ Place reflector at position ➀ supply voltage ON supply voltage ON
until »on« or »off« is until »on« or »off« is
displayed displayed

Press T2 until countdown »on« or

passed from »- 8 -« to »- 0 -« »off«
Press T2 until »d« is shown Press T2 until »d« is shown Press T2 until »d« is shown
and NOC or NCC symbol is
displayed To activate or
deactivate press T1
Current measu- Current measu- Current measu- Symbol
ring value ring value ring value NOC or NCC »on« or
»off«
Place object at position ➁
To activate or
deactivate press T1
Current measu-
ring value

Press T2 until countdown

Press T2 until »End« is Press T2 until »End« is To change output function
passed from »- 8 -« to »- 0 -«
shown shown press T2
and »End« is displayed

Symbol
NOC or NCC

Press T1 and T2 simultaneous-

ly until »End« is displayed

Normal mode operation

Teach-in swítched output Normal mode operation

Usefull additional functions in Add-on menu (for experienced users only, settings not required for standard applications)
Start here
T1 + T2

Press T1 and T2 simultaneously for about 13 s
until »Add« is shown in the LED-display

T1 T2  T1  T1

T2  T1
T2 T2  T1 T2  T1  T1
T2  T1
T2  T1
T2  T1
T2  T1
T2 T2 
T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2

                     
T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2
 T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2  T1 + T2
          

T2 
T1

T1 + T2
 »C01«: Display
bright
Minimum value:
»001«
»F00«: no filter Defines the strength
of the chosen filter.
Delay in seconds
between the detec-
Minimum value:
blind zone
»00«: synchronisati-
on
To optimize multi-
plex speed the hig-
Minimum value: sen-
sor-distant window
Put plane reflector
vertically disposed in
Affects the size of
the detection zone.
»F01«: standard fil-
Ready »C02«: Display dim- Maximum value: dif- ter »P00«: weak filter
tion of an object
and the output of
Maximum value: ne- »01« to »10«: sensor
hest sensor address
may be set.
margin front of sensor: in
an exact distance of
»E01«: high
med ference between up to arwindow limit - 1 address for multi- Maximum value: 999
»F02«: averaging fil- the measured dis- 250 mm for mic+ »E02«: standard
maximum range and plex mode Setting range »01« mm for mic+
»C03«: Display off ter »P09«: strong filter tance in case of ob- 25... and mic+35...
detect point - 1 to »10« 25/...,mic+35/..., »E03«: slight
ject approach (beha- »oFF«: synchronisati- and 900 mm for all
»F03«: foreground 999 cm for mic+
During window ves as on-delay). on deactivated other typs.
filter 130/...,mic+340/...,
mode operation hys- Adjust display to
"00": 0 s (no delay) mic+600/...
teresis influences »F04«: background 250 mm or 900 mm.
up to
Note both detect points. filter Confirm calibration
Changes in the Add-on "20": 20 s response with T1 + T2.
menu may impair the time
sensor function.
A6, A7, A8 , A10 , A11,
A12 have influence on
the response time of
the sensor.
Low power mode Hysteresis Measurement filter Filter strength Response time Foreground Multiplex mode Multiplex mode Measurement range Calibration Detection zone
switched output suppression device addressing highest device display sensitivity
dd
 1 +UB
U
2 mic+25… mic+35… mic+130… mic+340… mic+600…
4 D
5 Sync/Com
3 -UB
1 pnp switched output

1 +UB
U
2
4 E
5 Sync/Com
3 -UB
1 npn switched output

Blind zone 0 to30 mm 0 to 60 mm 0 to 200 mm 0 to 350 mm 0 to 600 mm

Operating range 250 mm 350 mm 1.300 mm 3.400 mm 6.000 mm
Maximum range 350 mm 600 mm 2.000 mm 5.000 mm 8.000 mm
Angle of beam spread Please see detection zone Please see detection zone Please see detection zone Please see detection zone Please see detection zone
Transducer frequency 320 kHz 400 kHz 200 kHz 120 kHz 80 kHz
Resolution, sampling rate 0,18 mm 0,18 mm 0,18 mm 0,18 mm 0,18 mm
Reproducibility ± 0,15 % ± 0,15 % ± 0,15 % ± 0,15 % ± 0,15 %
Accuracy Temperature drift internal compensated, ≤ 2 % Temperature drift internal compensated, ≤ 2 % Temperature drift internal compensated, ≤ 2 % Temperature drift internal compensated, ≤ 2 % Temperature drift internal compensated, ≤ 2 %
may be deactivated1) (0,17%/K without compensation) may be deactivated1) (0,17%/K without compensation) may be deactivated1) (0,17%/K without compensation) may be deactivated1) (0,17%/K without compensation) may be deactivated1) (0,17%/K without compensation)
Detection zones

20 cm

10 cm

10 cm

20 cm
10 cm

10 cm

1,6 m

0,8 m

0,8 m

1,6 m

2,4 m

1,2 m

1,2 m

2,4 m
0,8 m

0,4 m

0,4 m

0,8 m
0 cm
5 cm

0 cm

5 cm

0m

0m
0m
for different objects:
The dark grey areas are determind 0 cm 0 cm 0m 0m 0m
with a thin round bar (10 or 27 mm dia.)
and indicate the typical operating range
of a sensor. In order to obtain the light grey
areas, a plate (500 x 500 mm) is introduced 5 cm 10 cm 0,8 m 1,2 m
into the beam spread from the side. ausgerichtete
Plate Platte ausgerichtete
Plate Platte 0,4 m Plate
ausgerichtete Platte Plate
ausgerichtete Platte
In doing so, the optimum angle between ausgerichtete Platte
Plate
plate and sensor is always employed.
10 cm 1,6 m 2,4 m
This therefore indicates the maximum 20 cm
Rohr ø 10bar
Round mm Round
Rohr ø 27bar
mm Round
Rohr ø 27bar
mm
detection zone of the sensor. Round
Rohr ø 27bar
mm
0,8 m
It is not possible to evaluate ultrasonic Round
Rohr ø 27bar
mm
reflections outside this area. 15 cm 2,4 m 3,6 m
30 cm

35 cm 1,2 m
20 cm 1,3 m 3,2 m 4,8 m
40 cm 3,4 m

25 cm 1,6 m 4m 6m
50 cm

30 cm 4,8 m 7,2 m
60 cm 2m

35 cm 5,6 m 8,4 m

Opperating voltage UB 9 V to 30 V DC, reverse polarity protection 9 V to 30 V DC, reverse polarity protection 9 V to 30 V DC, reverse polarity protection 9 V to 30 V DC, reverse polarity protection 9 V to 30 V DC, reverse polarity protection
Voltage ripple ±10 % ±10 % ±10 % ±10 % ±10 %
No-load supply current ≤ 80 mA ≤ 80 mA ≤ 80 mA ≤ 80 mA ≤ 80 mA
Housing Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU;
Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam,
epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content
Class of protection to EN 60529 IP 67 IP 67 IP 67 IP 67 IP 67
Norm conformity EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2
Type of connection 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT
Controls 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl)
Indicators 3-digit LED-display, 2 three-colour LEDs 3-digit LED-display, 2 three-colour LEDs 3-digit LED-display, 2 three-colour LEDs 3-digit LED-display, 2 three-colour LEDs 3-digit LED-display, 2 three-colour LEDs
Programmable Yes, with TouchControl and LinkControl Yes, with TouchControl and LinkControl Yes, with TouchControl and LinkControl Yes, with TouchControl and LinkControl Yes, with TouchControl and LinkControl
Operating temperature -25°C to +70°C -25°C bis +70°C -25°C bis +70°C -25°C bis +70°C -25°C bis +70°C
Storage temperature -40°C to +85°C -40°C bis +85°C -40°C bis +85°C -40°C bis +85°C -40°C bis +85°C
Weight 150 g 150 g 150 g 210 g 270 g
Switching hysteresis1) 3 mm 5 mm 20 mm 50 mm 100 mm
switching frequency1) 11 Hz 8 Hz 6 Hz 3 Hz 2 Hz
Response time1) 50 ms 70 ms 110 ms 180 ms 240 ms
Time delay before availibility < 300 ms < 300 ms < 300 ms < 300 ms < 300 ms

Order No. mic+25/D/TC mic+35/D/TC mic+130/D/TC mic+340/D/TC mic+600/D/TC

Switched output pnp, UB - 2 V, Imax = 200 mA pnp, UB - 2 V, Imax = 200 mA pnp, UB - 2 V, Imax = 200 mA pnp, UB - 2 V, Imax = 200 mA pnp, UB - 2 V, Imax = 200 mA
switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof

Order No.
mic+25/E/TC mic+35/E/TC mic+130/E/TC mic+340/E/TC mic+600/E/TC
Switched output
npn, -UB + 2 V, Imax = 200 mA npn, -UB + 2 V, Imax = 200 mA npn, -UB + 2 V, Imax = 200 mA npn, -UB + 2 V, Imax = 200 mA npn, -UB + 2 V, Imax = 200 mA
switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof
1) Can be programmed with TouchControl and LinkControl

The contents of this document are subject to technical changes. Specifications are presented in a descripted way only. They
do not warrant product features.
Sensor Partners BV • Postbus 270 • 5151 AG Drunen • The Netherlands • Phone +31 (0)416 - 378239 • Fax +31 (0)416 - 377439 • E-Mail info@sensor.nl • Internet www.sensor.nl Sensor Partners BV