HL1606 is an LED driver IC that uses SPI communication to control LEDs. It allows for complex lighting effects through fewer data inputs. It has features like NMOS output, PWM output at 500Hz, internal modes for fading LEDs in/out with only data input, and a speed control bit to double the rate of LED changes. It can drive 2 pixels from its 3 outputs and uses SPI to control 16 LEDs in groups of 3 through input pins and internal fading modes.
HL1606 is an LED driver IC that uses SPI communication to control LEDs. It allows for complex lighting effects through fewer data inputs. It has features like NMOS output, PWM output at 500Hz, internal modes for fading LEDs in/out with only data input, and a speed control bit to double the rate of LED changes. It can drive 2 pixels from its 3 outputs and uses SPI to control 16 LEDs in groups of 3 through input pins and internal fading modes.
HL1606 is an LED driver IC that uses SPI communication to control LEDs. It allows for complex lighting effects through fewer data inputs. It has features like NMOS output, PWM output at 500Hz, internal modes for fading LEDs in/out with only data input, and a speed control bit to double the rate of LED changes. It can drive 2 pixels from its 3 outputs and uses SPI to control 16 LEDs in groups of 3 through input pins and internal fading modes.
HL1606 is an LED driver IC that uses SPI communication to control LEDs. It allows for complex lighting effects through fewer data inputs. It has features like NMOS output, PWM output at 500Hz, internal modes for fading LEDs in/out with only data input, and a speed control bit to double the rate of LED changes. It can drive 2 pixels from its 3 outputs and uses SPI to control 16 LEDs in groups of 3 through input pins and internal fading modes.
DESCRIPTION HL1606 is a LED driver IC with SPI controlled. We can get “complex mode changes” by fewer data.
FEATURES NMOS output SPI controlled，plus synchronization speed control port: S-I PWM output,frequency:500Hz With a internal “change model” unit，only data calls, reducing the amount of data. Speed control bit，can speed up “changes in a pixel” rate of 2 times. Latch enable bit，concatenated string at a point can be read or not read data. Built-6 road, drive two pixels（three-output get a pixel）
Control bit Latch A1（B1）Control bit A2（B2）Control bit A3（B3）Control bit of speed enable bit
Page 1 / 6 D2=0、D1=0 A1 Light out D4=0、D3=0 A2 Light out D6=0、D5=0 A3 Light out D7=0 D8=0 Default Can not D2=0、D1=1 A1 Light on D4=0、D3=1 A2 Light on D6=0、D5=1 A3 Light on rate latch
2 times Allowed to D2=1、D1=1 A1 fadeout D4=1、D3=1 A2 fadeout D6=1、D5=1 A3 fadeout rate latch Description of build-in module Fadein module： When a data bit is 10(D2D1 or D4D3 or D6D5) and the latch is enable, corresponding output state of LED is fadein. After get the brightest state, it will keep the state, until the new data input by effective latch. Fadeout module： When a data bit is 11(D2D1 or D4D3 or D6D5) and the latch is enable, corresponding output state of LED is fadeout. After the lights out, it will keep the state, until the new data input by effective latch. T Cycle time of change--T： When D7=0,T=Tzc×128 set ,series is 128. For example: When Zc=50Hz,T=2.56s,if every latch is effective, fadein/fadeout module will resume the change. Electric parameter （VDD=5V，temperature=25℃） ITEM SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Threshold voltage of output VOL IDS≤1µA，VDD=5V -- -- 6 V tube Stable and functioning Operating voltage VCC 3 5 5.5 V properly Operating current ICC VDD=5V，oscillations, no load -- 200 400 µA DATA input, changes of high Stable and functioning VIN 3.8 -- 6 V level and low level properly Output current of drive IOL VDD=5V，VDS=0.8V -- 30 -- mA IOH VDD=5V，VDS=-0.8V -- 5 -- mA Output current of buffer IOL VDD=5V，VDS=0.8V -- 10 -- mA temperature Temp 0 25 70 ℃ Work frequency of Fs VDD=5V 200 Hz terminal-S
Page 2 / 6 Timing diagram(entry data from high level) t0≥300ns ；t1≥1µs；T≥250N(ns)，N: the number of cascade；t2≈100ns。
Impression Drawing & Data Format
1. Monochrome , one-way, gradually run
Running direction
Description: There is a “gradual change” mode in HL1606, so D_I only need one set of data”10110000”, then input ”0” to the end is okay. Clock signal has been sent to CK_I, sent a “1” to L_I after 8 clock signal. Change once the signal of S_I, the output decline in a series. A clock cycle in S_I,. output is keep in 512Hz refresh frequency, to maintain the same level(series) of output duty cycle refresh. If no data sent to S_I, Page 3 / 6 output will remain the same duty cycle refresh.
2. Colorful fluttering
Fluttering direction
Description: There is a “gradual change” mode in HL1606, so D_I only need one set of data”10001011”, then input ”0” to the end is okay(red to green gradually). Clock signal has been sent to CK_I, sent a “1” to L_I after 8 clock signal. Change once the signal of S_I, the output series change once. A clock cycle in S_I,. output is keep in 512Hz refresh frequency, to maintain the same level(series) of output duty cycle refresh. If no data sent to S_I, output will remain the same duty cycle refresh. Just finished in a color change, change the data of D-I. 3.Full-color fluttering
Description: There is a “gradual change” mode in HL1606, so D_I only need one set of data”10001001”, Page 4 / 6 then input ”0” to the end is okay(red to yellow gradually). Clock signal has been sent to CK_I, sent a “1” to L_I after 8 clock signal. Change once the signal of S_I, the output series change once. A clock cycle in S_I,. output is keep in 512Hz refresh frequency, to maintain the same level(series) of output duty cycle refresh. If no data sent to S_I, output will remain the same duty cycle refresh. Just finished in a color change, change the data of D-I.
