Piping Specification Breaks

PIPING SPECIFICATION BREAKS
Specification breaks are required in piping systems for transition from high to
low pressure, between high and low temperature service (sometimes), and
between corrosive and non-corrosive environments. Temperature is also a
consideration because it has an effect on material strength and corrosion
resistance.
When setting specification breaks it is important to look at the complete

piping system from source to destination. The specification break must be
positioned so that there is no possibility for the lower pressure, lower/higher
temperature or less corrosive resistant piping to be exposed to the harsher
condition under any circumstance. Situations to consider include; operator or
instrument failure, startup/shut down conditions, line plugging due to hydrate
formation or water deposition and freezing, Joule-Thompson expansion (sub-
cooling) and plugging with corrosion products or dirt. Also, the destination
system must be properly protected with appropriately sized relief valves,
vents, etc.
Methods that are used to protect a lower pressure piping system downstream
from the specification break can include:
a. No valves downstream
b. CSO valves downstream, plus a stringent management policy for such
valves.
c. Where appropriate, instrument and control valve failure modes that
ensure piping system integrity.
d. Tracing and insulation where appropriate to prevent hydrate formation
and ice plugs.
e. Frequent inspection where line plugging or corrosion is suspected to be a
problem.
f. Thermal expansion reliefs for trapped fluids.
Where appropriate, the procedural solutions discussed above can be covered

in a note on the P&ID, and ultimately can be addressed in the plant operating
procedures.
Note: Reference is made to API RP 14J for pressure breaks (Fig 3 to Fig 6,
Page 19 & 20) on a typical offshore oil & gas production facility.
10.1 High-pressure process systems flowing into lower pressure process
systems
Locate the specification break at the outlet flange of the furthest downstream
block valve in the system that is not protected by one of the methods
listed above.
L o w T e m p M a te r ia l S p e c B re a k
H ig h e r P re s su re S p e c L o w e r P re ssu re S p e c
10.2 High-pressure gas or mixed phase systems flowing into lower

pressure systems, resulting in Joule Thomson cooling.
If the Joule Thomson cooling can result in a temperature that

requires special low temperature piping, locate the low temperature
material specification break at the inlet flange of the control or globe
valve in the system as illustrated below and the pressure
specification break as illustrated in figure below. The piping
downstream of the pressure specification break also needs to be low
temperature material.
NC NC
Min
600 mm
HT Spec LT Spec
Key : HP Spec LP Spec
: Globe Valve
10.3 High-pressure utility systems flowing into lower pressure process
systems.
Locate the specification break at the outlet flange of the furthest

downstream block valve in the utility line.
Utility Spec. Process Spec
10.4 Non-Corrosive material flowing into a corrosive system.
Generally, there will be a check valve in the line to prevent corrosive

material from back flowing into the non-corrosive resistant system
and block valve or control valve to control or shut off flow. If the
check valve is upstream of the block or control valve, locate the
material specification break at the inlet flange to the check valve. If
the check valve is downstream of the block or control valve, locate
the material specification break at the inlet flange to the block or
control valve.
N o n -C o r ro s iv e S p e c . C o r r o s iv e S p e c .
10.5 Corrosive material flowing into a non-corrosion resistant system.
As a minimum, the specification break should be at the last valve

flange (block or check) before the material enters the non-corrosive
system. If the corrosive material flow is continuous, this may not be
enough. Depending on the nature of the corrosive material, it may be
necessary to use an injection quill or to provide corrosion resistant
materials in the non-corrosion resistant piping system a few
diameters upstream and downstream of the mix point. If there is any
doubt about the application, a metallurgist should be consulted.
In cases where there is a corrosive material and also pressure

differences that would cause piping specification changes, both need
to be considered. In some unusual cases, this might result in two
specification breaks; one for pressure and the other for piping
metallurgy.
N o n - C o r r o s iv e S p e c . C o r r o s iv e S p e c .
10.6 Pump suction piping components should be rated for pump discharge
pressure downstream of:
a. automatically operated suction valves, and

b. manually operated suction or pump isolation valve which may
be erroneously closed out of sequence (e.g. during a
maintenance operation).
This may be waived if appropriate administrative controls are

provided that preclude the operation of the suction valve(s) prior to
adequate isolation from high pressure sources, and a properly sized
relief path is available that will prevent the suction piping from
being overpressured.
If the discharge of the pump enters a high pressure system which has
an independent source of pressure which could overpressure the
pump suction in the event of a pump shutdown and discharge check
valve failure, then a pump discharge SDV actuated by pump SD or
suction PSH is required. Example of such an installation would be
crude shipping pumps discharging into pipelines with several
independent pressure sources.
10.7 Compressor piping should be rated and specification breaks shown
based on the following:
a. For positive displacement type compressors (e.g. reciprocating),

all piping downstream of and including the suction block valve
should be equal in design rating to the discharge piping.
b. For kinetic energy type compressors (e.g. centrifugal), the pressure rating of the
suction piping downstream of and including the suction block valve(s) should be at or
above the settle out pressure of the compressor system following emergency or other
shutdown of the compressor.

Piping Specification Breaks

Uploaded by

Copyright:

Available Formats

Piping Specification Breaks

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Piping Specification Breaks

Uploaded by

Copyright:

Available Formats

What factors need to be considered when setting specification breaks in piping systems?

What methods can be used to protect a lower pressure piping system downstream from the specification break?

PIPING SPECIFICATION BREAKS

When setting specification breaks it is important to look at the complete

Where appropriate, the procedural solutions discussed above can be covered

10.2 High-pressure gas or mixed phase systems flowing into lower

If the Joule Thomson cooling can result in a temperature that

Key : HP Spec LP Spec

Locate the specification break at the outlet flange of the furthest

Utility Spec. Process Spec

10.4 Non-Corrosive material flowing into a corrosive system.

Generally, there will be a check valve in the line to prevent corrosive

As a minimum, the specification break should be at the last valve

In cases where there is a corrosive material and also pressure

a. automatically operated suction valves, and

This may be waived if appropriate administrative controls are

a. For positive displacement type compressors (e.g. reciprocating),

You might also like