2-wire transmitter with HART protocol

5335D
– RTD, TC, Ohm, or mV input
– Extremely high measurement accuracy
– HART 5 protocol
– Galvanic isolation
– For DIN form B sensor head mounting

Application
Applications
• Linearized temperature measurement with Pt100...Pt1000,
Ni100...Ni1000, or TC sensor.
• Difference or average temperature measurement of 2
resistance or TC sensors.
• Conversion of linear resistance variation to a standard analog
current signal, for instance from valves or Ohmic level
sensors.
• Amplification of a bipolar mV signal to a standard 4...20 mA
current signal.
• Connection of up to 15 transmitters to a digital 2-wire signal
with HART communication.

Technical characteristics
• Within a few seconds the user can program PR5335D to
measure temperatures within all ranges defined by the norms.
• The RTD and resistance inputs have cable compensation for
2-, 3- and 4-wire connection.
• The 5335D has been designed according to strict safety
requirements and is therefore suitable for application in SIL
installations.
• Continuous check of vital stored data for safety reasons.
• Sensor error detection according to the guidelines in NAMUR
NE89.

Mounting / installation
• For DIN form B sensor head mounting.

This page is automatically generated on the basis of information provided on www.prelectronics.com and affiliated websites. It is provided to you as a service and for information
purpose only. While we have attempted to maintain the information as accurately as possible, the page may contain errors or omissions for which we disclaim any and all liability
Environmental Conditions Output specifications
Operating temperature................................... -40°C to +85°C
Current output
Calibration temperature................................. 20...28°C
Signal range................................................... 4…20 mA
Relative humidity............................................ < 95% RH (non-cond.)
Min. signal range............................................ 16 mA
Protection degree (encl./terminal).................. IP68 / IP00
Load (@ current output)................................. ≤ (Vsupply - 8) / 0.023 [Ω]
Load stability.................................................. ≤ 0.01% of span / 100 Ω
Mechanical specifications Sensor error indication................................... Programmable 3.5…23 mA
Dimensions.................................................... Ø 44 x 20.2 mm NAMUR NE43 Upscale/Downscale............... 23 mA / 3.5 mA
Weight approx................................................ 50 g
Wire size........................................................ 1 x 1.5 mm2 stranded wire of span........................................................... = of the presently selected
range
Screw terminal torque.................................... 0.4 Nm
Vibration......................................................... IEC 60068-2-6
2...25 Hz......................................................... ±1.6 mm I.S. / Ex marking
25...100 Hz..................................................... ±4 g ATEX.............................................................. II 1 G Ex ia IIC T4...T6 Ga, II 1
D Ex ia IIIC Da, I M1 Ex ia Ma
Common specifications IECEx............................................................. Ex ia IIC T4...T6 Ga, Ex ia IIIC
Da, Ex ia I Ma
Supply FM, US........................................................... Cl. I, Div. 1, Gp. A, B, C, D
Supply voltage............................................... 8.0...30 VDC T4/T6; Cl. I Zone 0, AEx ia IIC
T4/T6; Cl. 1, Div. 2, Gp. A, B,
Isolation voltage C, D, T4/T6
Isolation voltage, test / CSA................................................................ Cl. I, Div. 1, Gp. A, B, C, D Ex
working........................................................... 1.5 kVAC / 50 VAC ia IIC, Ga
INMETRO....................................................... Ex ia IIC T6...T4 Ga, Ex ia IIIC
Response time Da, Ex ia I Ma
Response time (programmable).................... 1...60 s
Warm-up time................................................. 30 s Observed authority requirements
Programming................................................. Loop Link & HART EMC............................................................... 2014/30/EU
Signal / noise ratio......................................... Min. 60 dB ATEX.............................................................. 2014/34/EU
Accuracy........................................................ Better than 0.05% of selected RoHS.............................................................. 2011/65/EU
range EAC................................................................ TR-CU 020/2011
Signal dynamics, input................................... 22 bit EAC Ex........................................................... TR-CU 012/2011
Signal dynamics, output................................. 16 bit
Effect of supply voltage change..................... < 0.005% of span / VDC Approvals
EMC immunity influence................................ < ±0.1% of span DNV Marine.................................................... TAA0000101
Extended EMC immunity: NAMUR ATEX.............................................................. KEMA 03ATEX1537
NE21, A criterion, burst.................................. < ±1% of span
IECEx............................................................. KEM 10.0083X
c FM us.......................................................... FM17US0013X
Input specifications CSA................................................................ 1125003
Common input specifications INMETRO....................................................... DEKRA 18.0002X
Max. offset...................................................... 50% of selected max. value EAC Ex........................................................... RU C-DK.HA65.B.00355/19
SIL.................................................................. Hardware assessed for use in
RTD input SIL applications
RTD type........................................................ Pt100, Ni100, lin. R
Cable resistance per wire.............................. 5 Ω (up to 50 Ω per wire is
possible with reduced
measurement accuracy)
Sensor current............................................... Nom. 0.2 mA
Effect of sensor cable resistance
(3-/4-wire)....................................................... < 0.002 Ω / Ω
Sensor error detection................................... Yes

TC input
Thermocouple type........................................ B, E, J, K, L, N, R, S, T, U,
W3, W5
Cold junction compensation
(CJC).............................................................. < ±1.0°C
Sensor error detection................................... Yes
Sensor error current: When
detecting / else............................................... Nom. 33 μA / 0 μA

Voltage input
Measurement range....................................... -800...+800 mV
5335D-012221

Min. measurement range (span).................... 2.5 mV