GMA 347 Audio Panel Installation Manual: Garmin Ltd. or Its Subsidiaries

GMA 347
AUDIO PANEL
INSTALLATION
MANUAL
Garmin Ltd. or its subsidiaries
190-00325-01 Revision A
August 2005
© Copyright 2005
Garmin Ltd. or its subsidiaries
All Rights Reserved
Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated,
downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin.
Garmin hereby grants permission to download a single copy of this manual and of any revision to this manual onto a
hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision
hereto, provided that such electronic or printed copy of this manual or revision must contain the complete text of
this copyright notice and provided further that any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
Garmin International, Inc.

st
1200 E. 151 Street
Olathe, KS 66062 USA
Telephone: 913-397-8200
www.garmin.com
Garmin (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park Industrial Estate
Romsey, SO51 9DL, U.K.
Telephone: 44/0870.851241
RECORD OF REVISIONS
Revision Revision Description ECO #

Date
A 8/24/05 Initial Release 33101
DOCUMENT PAGINATION
Section Page Range

Table of Contents i-viii
Section 1 1-1 – 1-6
Section 2 2-1 – 2-8
Section 3 3-1 – 3-14
Section 4 4-1 – 4-14
Section 5 5-1 – 5-10
Appendix A A-1-A-6
Appendix B B-1-B-6
Appendix C C-1-C-24
Page A GMA 347 Installation Manual

Revision A 190-00325-01
NOTE
At the time of this edition, the current software version for the GMA 347 is 2.09.
The software version and information in this document are subject to change without
notice. Visit the Garmin web site (www.garmin.com) for current manual updates and
supplemental information concerning the operation of this and other Garmin
products.
INFORMATION SUBJECT TO EXPORT CONTROL LAWS
This document may contain information which is subject to the Export Administration Regulations
("EAR") issued by the United States Department of Commerce (15 CFR, Chapter VII, Subchapter C) and
which may not be exported, released, or disclosed to foreign nationals inside or outside of the United
States without first obtaining an export license. A violation of the EAR may be subject to a penalty of up
to 10 years imprisonment and a fine of up to US $1,000,000 under Section 2410 of the Export
Administration Act of 1979. Include this notice with any reproduced portion of this document.
WARNING
This product, its packaging, and its components contain chemicals known to the state of California to
cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with
California’s proposition 65. If you have any questions or would like additional information, please refer
to our web site at www.garmin.com/prop65.
GMA 347 Installation Manual Page i

190-00325-01 Revision A
This page intentionally left blank
Page ii GMA 347 Installation Manual

Revision A 190-00325-01
TABLE OF CONTENTS
PARAGRAPH PAGE
1 GENERAL DESCRIPTION..............................................................................................................1-1
1.1 Introduction........................................................................................................................................1-1
1.2 Equipment Description ......................................................................................................................1-1
1.3 Technical Specifications ...................................................................................................................1-3
1.4 Certification .......................................................................................................................................1-5
1.5 Reference Documents ........................................................................................................................1-6
1.6 Limited Warranty...............................................................................................................................1-6
2 INSTALLATION OVERVIEW ........................................................................................................2-1

2.1 Introduction........................................................................................................................................2-1
2.2 Wiring ................................................................................................................................................2-1
2.3 Cooling Air ........................................................................................................................................2-1
2.4 Installation Materials .........................................................................................................................2-2
2.5 GMA 347 Wiring and Software Configuration Options....................................................................2-3
2.6 Marker Beacon Antenna Installation .................................................................................................2-5
2.7 Installation Approval Considerations for Pressurized Aircraft..........................................................2-6
2.8 Electrical Noise..................................................................................................................................2-6
2.9 GMA 347 Mounting ..........................................................................................................................2-7
3 INSTALLATION PROCEDURE......................................................................................................3-1
3.1 Unpacking Unit..................................................................................................................................3-1
3.2 Marker Beacon Antenna Installation .................................................................................................3-1
3.3 Marker Beacon Antenna Cable Connectors.......................................................................................3-1
3.4 Electrical Connections .......................................................................................................................3-1
3.5 Backshell Assembly and D-Subminiature Connectors ......................................................................3-3
3.6 Circuit Breaker Placard....................................................................................................................3-11
3.7 GMA 347 Unit Installation ..............................................................................................................3-11
3.8 Post Installation Configuration and Checkout .................................................................................3-11
4 SYSTEM INTERCONNECTS..........................................................................................................4-1
4.1 Connector Description .......................................................................................................................4-1
4.2 Connectors J3471 and J3472 .............................................................................................................4-1
4.3 J3472 Connector Pin Assignments ....................................................................................................4-6
4.4 J3471 Connector Pin Assignments ..................................................................................................4-10
GMA 347 Installation Manual Page iii

190-00325-01 Revision A
TABLE OF CONTENTS
PARAGRAPH PAGE
5 POST INSTALLATION CONFIGURATION AND CHECKOUT PROCEDURE .........................5-1

5.1 Post Installation Configuration Harness ............................................................................................5-1
5.2 Program Information..........................................................................................................................5-1
5.3 GMA Configuration Tool Version ....................................................................................................5-1
5.4 GMA Configuration Tool Introduction .............................................................................................5-1
5.5 Connect and Disconnect Buttons.......................................................................................................5-2
5.6 Configuration Tool Settings ..............................................................................................................5-4
5.7 Marker Beacon...................................................................................................................................5-5
5.8 Keypad Annunciators ........................................................................................................................5-5
5.9 Configuration Inputs..........................................................................................................................5-5
5.10 Code Upload ......................................................................................................................................5-6
5.11 Configuration Example......................................................................................................................5-9
5.12 Valid Data Ranges ...........................................................................................................................5-10
APPENDIX A CERTIFICATION DOCUMENTS

A.1 Airworthiness Approval.................................................................................................................... A-1
A.2 Continued Airworthiness .................................................................................................................. A-1
A.3 Environmental Qualification Forms, GMA 347 Audio Panel .......................................................... A-3
APPENDIX B ASSEMBLY AND INSTALLATION DRAWINGS
APPENDIX C INTERCONNECT DRAWINGS
LIST OF ILLUSTRATIONS
FIGURE PAGE
2-1 GMA 347 Unit Rack .........................................................................................................................2-7
3-1 Shield Block Install onto Backshell Connector Assembly ................................................................3-4

3-2 Shielded Cable Preparation................................................................................................................3-5
3-3 Daisy Chain Method for Shield Termination.....................................................................................3-8
3-4 Parallel Shield Termination ...............................................................................................................3-8
3-5 Configuration Module Installation...................................................................................................3-10
4-1 Back of Unit, Connector Location .....................................................................................................4-1

4-2 Rear Connectors J3471 and J3472, Viewed From Back of Unit .......................................................4-1
4-3 GMA 347 Configuration Upload Connections ..................................................................................4-7
Page iv GMA 347 Installation Manual

Revision A 190-00325-01
LIST OF ILLUSTRATIONS
FIGURE PAGE
5-1 About GMA Config Tool ..................................................................................................................5-1

5-2 GMA Configuration Tool Screen ......................................................................................................5-2
5-3 Connecting to the GMA 347..............................................................................................................5-2
5-4 Radio Button Not Chosen and Upload Selected ................................................................................5-6
5-5 File Selection .....................................................................................................................................5-6
5-6 Wrong Hex File Selected (Selecting Boot Code for System Code Upload)......................................5-6
5-7 Wrong Hex File Selected (Selecting System Code for System Code Upload)..................................5-7
5-8 Erasing Flash .....................................................................................................................................5-7
5-9 Uploading Flash.................................................................................................................................5-7
5-10 Canceling a Code Upload ..................................................................................................................5-7
5-11 Code Upload Failed ...........................................................................................................................5-8
5-12 Code Upload Complete......................................................................................................................5-8
A-1 GMA 347 Environmental Qualification Form ................................................................................. A-4

B-1 GMA 347 Outline Drawing .............................................................................................................. B-1
B-2 GMA 347 Rack Dimensions (115-00427-00)................................................................................... B-3
B-3 GMA 347 Connector/Rack Assembly Drawing .............................................................................. B-5
C-1 GMA 347 Power, Antenna and Speaker Interconnect Wiring Diagram........................................... C-1
C-2 Mic and Phone Jack Connections, Interconnect Wiring Diagram .................................................... C-3
C-3 Transceiver Analog Connections, Interconnect Wiring Diagram..................................................... C-5
C-4 Discrete Lines, Interconnect Wiring Diagram .................................................................................. C-7
C-5 GMA 340 to GMA 347 Comparison ................................................................................................ C-9
GMA 347 Installation Manual Page v

190-00325-01 Revision A
LIST OF TABLES
TABLE PAGE
3-1 Pin Contact Part Numbers..................................................................................................................3-1

3-2 Recommended Crimp Tools ..............................................................................................................3-2
3-3 Backshell Assembly...........................................................................................................................3-3
3-4 Shield Block Components .................................................................................................................3-4
3-5 Shielded Cable Preparation................................................................................................................3-5
3-6 Configuration Module Kit – 011-00979-00.......................................................................................3-9
3-7 Configuration Module Wire Color Reference Chart .......................................................................3-10
4-1 J3471 Pin Assignments......................................................................................................................4-2
4-2 J3472 Pin Assignments......................................................................................................................4-4
4-3 Aircraft Power Pin Assignments, J3472 ............................................................................................4-6
4-4 Aircraft Lighting Pin Assignments, J3472.........................................................................................4-6
4-5 RS-232 Pin Assignments, J3472........................................................................................................4-7
4-6 Marker Beacon Pin Assignments, J3472 ...........................................................................................4-8
4-7 Installation Selection Inputs Pin Assignments, J3472 .......................................................................4-8
4-8 External Configuration Module Pin Assignments, J3472..................................................................4-9
4-9 Speaker Pin Assignments, J3472 .......................................................................................................4-9
4-10 PA MUTE Pin Assignments, J3472 ..................................................................................................4-9
4-11 Mic Audio Inputs and Mic Key Pin Assignments, J3471................................................................4-10
4-12 ICS Key Pin Assignments, J3471 ....................................................................................................4-10
4-13 Com Audio and Mic Keys Pin Assignments, J3471........................................................................4-11
4-14 Nav Audio Pin Assignments, J3471 ................................................................................................4-11
4-15 Headset Outputs Pin Assignments, J3471 .......................................................................................4-11
4-16 Music Inputs Pin Assignments, J3471 .............................................................................................4-12
4-17 Unswitched Audio Inputs Pin Assignments, J3471.........................................................................4-12
4-18 Telephone Inputs/Outputs Pin Assignments, J3471 ........................................................................4-12
4-19 AUX, DME and ADF Audio Pin Assignments, J3471....................................................................4-13
4-20 Failsafe Audio Pin Assignments, J3471 ..........................................................................................4-13
Page vi GMA 347 Installation Manual

Revision A 190-00325-01
GMA 347 HARDWARE MOD LEVEL HISTORY
The following table identifies hardware modification (Mod) Levels for the GMA 347 Audio Panel. Mod
Levels are listed with the associated service bulletin number, service bulletin date, and the purpose of the
modification. The table is current at the time of publication of this manual (see date on front cover) and is
subject to change without notice. Authorized Garmin Sales and Service Centers are encouraged to access
the most up-to-date bulletin and advisory information on the Garmin Dealer Resource web site at
www.garmin.com using their Garmin-provided user name and password.
MOD SERVICE SERVICE PURPOSE OF MODIFICATION

LEVEL BULLETIN BULLETIN
NUMBER DATE
GMA 347 Installation Manual Page vii

190-00325-01 Revision A
Page viii GMA 347 Installation Manual

Revision A 190-00325-01
1 GENERAL DESCRIPTION
1.1 Introduction
This manual presents mechanical and electrical installation requirements for installing the Garmin
GMA 347 Audio Panel. The GMA 347 can be installed into a variety of airframes by means of an STC,
TC or Field Approval. Each airframe installation may vary. Use only approved data for specific
installation instructions in a particular aircraft. After installation of the GMA 347, FAA Form 337 must
be completed by an appropriately certificated agency to return the aircraft to service.
1.2 Equipment Description
CAUTION
The operation of cellular telephones or other cellular mobile devices aboard aircraft while
airborne is prohibited by FCC rules. Due to the potential for interference with onboard
systems, the operation of cellular communication devices while onboard an aircraft that is
on the ground is subject to (FAA) 14 CFR 91.21.
(FCC) 47 CFR 22.925 prohibits airborne operation of cellular telephones installed in or

carried aboard aircraft. Cellular telephones must not be operated aboard any aircraft
while the aircraft is off the ground. When any aircraft leaves the ground, all cellular
telephones on board that aircraft must be turned off.
Cellular telephones that are on, even in a monitoring state, can disrupt GPS performance.
The Garmin GMA 347 is a horizontally oriented panel-mounted audio control panel and marker beacon
system. The system delivers reliability and versatility for all audio controlling functions. LED-
illuminated pushbuttons and logical panel layout allow audio selection of NAV, COM. LED annunciator
brightness is adjusted to an appropriate level for ambient cockpit light conditions automatically by
photocell dimming. Key brightness is controlled manually with the radio lighting dimming bus. A
failsafe circuit connects the pilot’s left headset channel and microphone directly to COM 1 in case power
is interrupted or the unit is turned off.
The Garmin GMA 347 Audio Panel incorporates a microcontroller for processing front panel key
commands, annunciator control, input/output functions, and communication.
The GMA 347 includes a six-position intercom system (ICS) with electronic cabin noise de-emphasis,
two stereo music inputs, and combined pilot, copilot, and passenger volume controls. The intercom
provides four selectable modes of isolation (All, Crew, Pilot, Copilot). A pilot-selectable cabin speaker
output can be used to listen to the selected aircraft radios or to broadcast PA announcements. The PA
function is pilot selectable.
The GMA 347 provides a digital voice recorder with playback capability. Recording is automatic when a
COM signal is received. Playback is controlled by pressing the PLAY button or a remote mounted
switch.
GMA 347 Installation Manual Page 1-1

190-00325-01 Revision A
The Recorder can be disabled using an external switch. The digital recorder can playback up to two and a
half minutes of recording. Refer to the GMA 347 Pilot’s Guide (190-00325-00) for complete system
operation.
The GMA 347 is FAA TSO approved to C50c and C35d Class A, and ETSO approved to C50c and
2C35d (pending). A marker beacon receiver with dual sensitivity and audio muting with automatic re-
arming is included in the unit. Operating voltage range is from 11 to 33 volts.
The GMA 347 provides two stereo auxiliary entertainment inputs; MUSIC 1 and MUSIC 2. Two 3.5 mm
stereo phone jacks should be installed in a convenient location for this purpose. These inputs are
compatible with popular portable entertainment devices such as MP3 and CD players. The headphone
outputs of these devices are plugged into the MUSIC 1 or MUSIC 2 jacks.
Only the pilot and copilot hear MUSIC 1. MUSIC 2 is a non-muted input heard only by the passengers.
MUSIC 1 and MUSIC 2 characteristics are affected by the active intercom mode. Refer to the GMA 347
pilot’s manual for details.
MUSIC 1 is soft-muted when an interruption occurs from an aircraft radio. Soft muting is the gradual
return of MUSIC 1 to its original volume level. MUSIC 1 can also be configured to mute during ICS
activity. MUSIC 2 is a non-muted input.
1.2.1 Features Summary
• Logical front panel layout

• LED annunciators indicate selected function
• Six position intercom: pilot, copilot, four passengers
• Three stereo headset amplifiers: one for pilot, one for copilot, and one for the passengers
• Two stereo music source inputs
• Four selectable intercom operational modes
• Independent pilot, copilot, and passenger volume control
• VOX control for mic inputs
• Automatic selection of radio audio source when corresponding mic is selected
• MASQTM Processing
• Split COM transceiver function. Copilot may transmit and receive on COM 2 while pilot
transmits and receives on COM 1
• COM swap function
• TX indication
• SmartMuteTM marker audio muting
• Autosquelch
• Speaker output for radios or PA function
• Power-off fail safe connection for Pilot PTT, mic and Pilot’s Headset-Left to COM 1
• Voice Recorder with Playback
• Configurable Options. See Sections 4 and 5 for connection and configuration details.
Page 1-2 GMA 347 Installation Manual

Revision A 190-00325-01
1.2.2 Interface Summary
The following is an interface summary for the GMA 347. See Section 4 and Appendix C for connection
details.
• 3 Transceiver Inputs (Figure C-3)

• 5 Receiver Inputs (Figure C-3)
• 4 Unswitched Inputs (Figures C-3)
• 2 Aircraft Power Inputs (Figure C-1)
• Discrete Inputs/Outputs (Figure C-4)
• Marker Beacon Antenna Input (Figure C-1)
• External Marker Beacon Lamp Driver Outputs (Figure C-4)
1.3 Technical Specifications

The following tables present general environmental specifications. For detailed specifications, see the
Environmental Qualification form in Appendix A.
1.3.1 Physical Characteristics
Specification Characteristic
Bezel Height 1.3 inches (33 mm)
Bezel Width 6.29 inches (160 mm)
Rack Height 1.325 (34 mm)
Rack Width 6.30 inches (160 mm)
Depth Behind Panel with 7.79 inches (198 mm)
Connectors (measured from face
of aircraft panel to rear of
connector backshells)
GMA 347 Unit Weight 1.7 lbs. (0.8 kg)
GMA 347 Rack Weight (Installed 2. 4 lbs. (1.1 kg)
with rack and connectors)

190-00325-01 Revision A
1.3.2 Electrical Characteristics
Specification Characteristic
Regulatory Compliance RTCA/DO-160D Environmental Conditions and EUROCAE/ED-14D
Unit Software RTCA/DO-178B Level D
Temperature Range -45°C to +70°C
Altitude 55,000 Feet
Audio Panel Transceiver inputs: 3

Receiver inputs: 5
Unswitched inputs: 4
Input impedance: 500
Input isolation: 60 dB minimum
Special functions: Failsafe operation, MASQTM
processing
Maximum Input: COM, NAV, DME, AUX, Failsafe, Unswitched inputs 1-3,
Altitude Warning; 4 V rms
TEL; 3.5 V rms
Intercom Positions: 6 (pilot, copilot, 4 passengers)
Volume controls: 2 (pilot, copilot/passengers)
VOX level controls: 2 (pilot, copilot/passengers)
VOX circuits: 6 (one per mic input)
Music inputs (stereo): 2 (one input mutable)
Music input impedance: 5 k
Music input level: Less than 500 mVac RMS for full output (typical).
1 Vac RMS MAX (3 Vac p-p)
Microphone signal processing: 9 pole characteristic and special cabin
noise band de-emphasis
Intercom isolation modes: 4 (All, Pilot Isolate, Copilot Isolate, Crew
Isolate)
Special functions: Recorder with playback (automatic recording of
selected COMs) up to 2.5 minutes of recording time.
Automatic squelch: 6 (one per mic input) pilot selectable between auto
and manual.
Headphone Outputs Output amplifiers: 3, stereo (pilot, copilot, passengers)
Fidelity: Power into 150 Distortion
50 mW <0.5%
100 mW <5%
Frequency response: music; 50 Hz to 20 kHz nominal
Aircraft radio: 200 Hz to 6 kHz nominal
ICS mic: (Special cabin noise band de-emphasis)
Speaker Outputs Outputs selectable: 1, pilot selectable
Output power: 10 watts into 4 or 8 , @ any normal supply voltage.
Frequency response: 350 Hz to 6 kHz nominal
Special functions: PA Mode, pilot selectable, including split operation
Marker Beacon Receiver Frequency: Crystal controlled at 75 MHz
Sensitivity: LO 1000 µV hard; HI 200 µV hard
Selectivity: 6 dB @ ±10 kHz min, 40 dB @ ±200 kHz max.
Input impedance: 50
External lamp drive: 125 mA max each output
Other outputs: Middle MKR sense
Special functions: SmartMuteTM marker audio muting

Revision A 190-00325-01
1.3.3 Power Requirements
Characteristic Specification
Input Voltage Range 11.0 to 33.0 Vdc. See the Environmental Qualification
Form in Appendix A for details on surge ratings and
minimum/maximum operating voltages.
Power Input Operating Current:
3.75 amps max at 13.75 V
1.75 amps max at 27.5 V
1.4 Certification
The conditions and tests required for TSO approval of this article are minimum performance standards. It
is the responsibility of those installing this article either on or within a specific type or class of aircraft to
determine that the aircraft installation conditions are within the TSO standards. TSO articles must have
separate approval for installation in an aircraft. The article may be installed only if performed under 14
CFR part 43 or the applicable airworthiness requirements.
1.4.1 TSO/ETSO Compliance

The GMA 347 is FAA TSO approved to TSO-C50c, TSO-C35d Class A, ETSO-C50c (pending) and
ETSO-2C35d (pending).
For a list of ETSO deviations see the GMA 347 Declaration of Design and Performance, Garmin part
number 190-00325-03.
1.4.2 TSO Deviations

The following table provides a list of applicable TSO deviations for the GMA 347.
TSO Deviation
TSO-C35d Garmin was granted a deviation from TSO-C35d to use RTCA DO-160D instead of RTCA
DO-138 as the standard for Environmental Conditions and Test Procedures for Airborne
Equipment.
Garmin was granted a deviation from TSO-C35d to use FAR §21.607(d) instead of FAR
§37.7 as the general rules governing holders of the TSO authorizations.
TSO-C50d Garmin was granted a deviation from TSO-C50d to use RTCA DO-178B instead of RTCA
DO-178A as the standard for Software Considerations in Airborne Systems and
Equipment Certification.
Garmin was granted a deviation from TSO-C50d to use RTCA DO-160D instead of RTCA
DO-160A as the standard for Environmental Conditions and Test Procedures for Airborne
Equipment.

190-00325-01 Revision A
1.5 Reference Documents
The following publications are sources of additional information for installing the GMA 347. Before
installing the unit, the technician should read all referenced materials along with this manual.
Part Number Document

190-00325-00 GMA 347 Pilot’s Guide
1.6 Limited Warranty

This Garmin product is warranted to be free from defects in materials or workmanship for two years from
the date of purchase. Within this period, Garmin will at its sole option, repair or replace any components
that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or
labor, provided that the customer shall be responsible for any transportation cost. This warranty does not
cover failures due to abuse, misuse, accident or unauthorized alteration or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY
LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR

CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR
INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not
allow the exclusion of incidental or consequential damages, so the above limitations may not apply to
you.
Garmin retains the exclusive right to repair or replace the unit or software or offer a full refund of the
purchase price at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE
REMEDY FOR ANY BREACH OF WARRANTY.
To obtain warranty service, contact your local Garmin Authorized Service Center. For assistance in
locating a Service Center near you, call Garmin Customer Service at one of the numbers shown below.
Products sold through online auctions are not eligible for rebates or other special offers from Garmin.
Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an
original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing
components from any package purchased through an online auction.
Garmin International, Inc. Garmin (Europe) Ltd.

1200 East 151st Street Unit 5, The Quadrangle, Abbey Park Industrial Estate
Olathe, Kansas 66062, U.S.A. Romsey, SO51 9DL, U.K.
Phone: 913/397.8200 Phone: 44/0870.851241
FAX: 913/397.0836 FAX: 44/0870.851251

Revision A 190-00325-01
2 INSTALLATION OVERVIEW
2.1 Introduction
This section provides hardware equipment information for installing the GMA 347 Audio Panel, related
hardware and suggestions relating to the marker beacon antenna. Installation of the GMA 347 should
meet the requirements of FAA Advisory Circulars AC 43.13-1B and AC 43.13-2A where applicable.
Cabling is fabricated by the installing agency to fit each particular aircraft.
2.2 Wiring
Use AWG #22 or larger wire for all connections unless otherwise specified in the interconnect diagrams
in Appendix C. The standard pin contacts supplied in the connector kit are compatible with up to AWG
#22 wire. In cases where some installations have more than one unit sharing a common circuit breaker,
sizing and wire gauge is based on aircraft circuit breaker layout, length of wiring, current draw of units,
and internal unit protection characteristics. Do not attempt to combine more than one unit on the same
circuit breaker unless it is specified on aircraft manufacturer approved drawings.
In some cases, a larger gauge wire such as AWG #18 or #16 may be needed for power connections.
Extended barrel contacts for AWG #16 and #18 wire are available from Garmin, if required. Special
thin-wall heat shrink tubing is also provided to insulate the extended barrels inside the backshell. If using
#16 or #18 barrel contacts, ensure that no two contacts are mounted directly adjacent to each other. This
minimizes the risk of contacts touching and shorting to adjacent pins and to ground.
Ensure that routing of the wiring does not come in contact with sources of heat, RF or EMI interference.
Check that there is ample space for the cabling and mating connectors. Avoid sharp bends in cabling and
routing near aircraft control cables.
2.3 Cooling Air

The GMA 347 does not have provisions for attaching cooling air and does not generate an excessive
amount of heat during typical operations, however the thermal characteristics of the installation should
always be assessed. An undesireable thermal condition could be created due to the unit's own internal
power dissipation combined with restricted ventilation, or due to heat generated by adjacent equipment.
Limiting thermal build up, by means of fan or natural convection is always a good practice and is
recommended to increase the product life.

190-00325-01 Revision A
2.4 Installation Materials
2.4.1 Configurations Available
The GMA 347 is available in three versions under the following part numbers. Catalog part numbers are
shown with and without the installation kit.
Model Front Panel Unit P/N Catalog P/N Installation

Color Kit
GMA 347 Black 011-00807-00 010-00275-00 No
GMA 347 Black 011-00807-00 010-00275-01 Yes
GMA 347 Gray 011-00807-10 010-00275-10 No
GMA 347 Gray 011-00807-10 010-00275-11 Yes
GMA 347H Black 011-00807-20 010-00275-20 No
GMA 347H Black 011-00807-20 010-00275-21 Yes
2.4.2 Equipment Available
Each of the following accessories is provided separately or in kit form for the GMA 347. The installation
kit includes the unit and the following hardware:
Item Garmin P/N

Sub Assy, Connector Kit, GMA 347 011-00813-01
SMP, Install Rack, GMA 347 115-00427-00
Sub Assy, Backplate, GMA 347 011-00812-00
Configuration Module Kit 011-00979-00
Garmin Marker Beacon Antenna Kit** 010-10175-00
** Note: A marker beacon antenna approved to TSO C35d that has been installed to meet the
requirements of this manual may be approved for use with the GMA 347.
2.4.3 Additional Equipment Required
• Antenna sealant (use manufacturer’s instructions, install according to FAA Advisory Circular
AC 43.13-2A).
• Cables: The installer will fabricate and supply all system cables. Interconnect wiring
diagrams are detailed in Appendix C.
• Hardware #6-32 x 100° Flat Head SS Screw [(MS24693, AN507R or other approved
fastener) (6 ea.)] and #6-32 Self-Locking Nut [MS21042 or other approved fastener (6 ea.)].
Hardware required to mount the installation rack is not provided.
• Stereo headphone jacks (up to 6), microphone jacks (up to 6), 3.5 mm stereo jacks (up to 2),
and insulating washers for all.

Revision A 190-00325-01
2.5 GMA 347 Wiring and Software Configuration Options
The GMA 347 can be configured in different ways for the flight crew. Consideration of options should
be discussed with the end user(s) of the aircraft before wiring begins. While Section 4 and Appendix C
contain connection details, the actual features employed or omitted are dependent on the wiring options
and the Software configuration selected. Refer to Section 5 for configuration instructions.
2.5.1 Hard Wiring Configuration Options
The following list shows the hard wiring configuration options available for the GMA 347.
Function and Purpose Hard Wiring Configuration Options

Com Swap. Transfers the active Com Swap Pushbutton Switch
microphone between Com 1 and
Com 2.
External lamps. Provides an extra External Marker Beacon Lights
set of Marker Beacon indicators
located away from the GMA 347.
Two Playback Options: Record Playback Pushbutton Switch
An external pushbutton activates
voice recorder playback.
A toggle switch enables or Record Playback Toggle Switch
disables recording.
PA MUTE is an output from the
GMA that is pulled low when PA mute
active. It is used to trigger the
mute function of an external PA
system.
A remote switch can be used to Remote Auxiliary Switch
enable or disable the auxiliary
input.

190-00325-01 Revision A
2.5.2 Software Configuration Options
The following list shows the software configurations available for the GMA 347. Configuration program
instructions are found in section 5.
Function and Purpose Software Configuration

Audio Inputs. Allow or disable the Enable or Disable DME, ADF, COM3, Play, PA,
use of external receivers SPKR, TEL, and Split COM
Defeate the (MASQ) Master Deactivate MASQ
Squelch feature
Telephone. Remove telephone Disable Telephone Channel
capability
Sidetone. Disable the sound of Enable or Disable Sidetone
transmission in the headset
COM MUTE ON TX Can be disabled. Audio on unselected COMs is
muted while the selected COM is transmitting
audio
COM MUTE ON RX Can be disabled. Audio on unselected COMs is
muted while the selected COM is receiving audio
Audio level. Volume control Adjust Audio level of Music 1 and Music 2,
adjustment Unswitched 1, Unswitched 2, Unswitched 3 and
Altitude Warning, SPKR, Pilot and Copilot Mic
Volume, Master Squelch Threshold, and Marker
volume
Marker Threshold Marker Beacon threshold levels are adjustable for
HI and LO sense
ICS Mute ICS Muting of Music 1 can be enabled or disabled
Record Com2 Pilot or Copilot COM recording. During the Split
Com mode, COM 1 or COM 2 audio can be
selected for voice recording and playback
2.5.1 Transmit Interlock and Split COM Operation
NOTE
Garmin makes no expressed or implied guarantees regarding the

suitability of the Split COM feature in any given installation.
In small aircraft, COM and Nav receiver interference is affected by both the distance between antennas
and the tuned frequency separation.
With transmit interlock activated in either the GMA 347 or the COM transceivers, Split COM operation
between a flight crew of more than one pilot is affected.
In aircraft that have a transmit interlock feature, when either transmitter is keyed, all other receivers are
muted so that they won’t pick up interference from the active COM transmitter. This is the preferred
option for single pilot operation.
For aircraft with two flight crew members, transmit-interlock would probably interfere with
communications. When the pilot or the copilot transmit, no audio is heard on any other receiver. This

Revision A 190-00325-01
For aircraft with two flight crew members, transmit-interlock would probably interfere with
communications. When the pilot or the copilot transmit, no audio is heard on any other receiver. This
means that if the pilot is communicating with ATC while the copilot transmits on another radio, all pilot
reception is cut off during the time of copilot transmission.
If the installation does not have transmit-interlock activated, all the receivers are listening all the time
whether any radio is transmitting or not. Split COM performance varies significantly across installations.
If the transceivers interfere with each other, transmission by one radio produces static or squeal, thus loss
of communication from any other radio.
2.6 Antenna Installation

2.6.1 Location Considerations
The marker beacon antenna should be mounted on a flat surface on the underside of the aircraft. Mount
the antenna so that there is a minimum of structure between it and the ground radio stations. Locate it as
far away as possible from transmitter antennas.
Best results with split COM mode will be obtained when the COM 1 and COM 2 antennas are mounted
on opposite sides of the aircraft (top/bottom).
2.6.2 Marker Beacon Antenna Mounting

Install the marker beacon antenna according to the antenna manufacturer’s instructions and FAA
Advisory Circulars AC 43.13-1B and AC 43.13-2A, Chapters 2 and 3, as applicable. If the antenna is
being installed on a composite aircraft, ground planes must be added. Conductive wire mesh, radials or
thin aluminum sheets embedded in the composite material provide the proper ground plane allowing the
antenna pattern (gain) to be maximized for optimum performance.
2.6.3 Marker Beacon Antenna Cable Installation

Use coaxial cable meeting the applicable aviation regulation for the marker beacon antenna. Any cable
meeting specifications is acceptable for the installation. When routing antenna cables, observe the
following precautions:
• All cable routing should be kept as short and as direct as possible.
• Avoid sharp bends.
• Avoid routing cables near power sources (e.g., 400 Hz generators, trim motors, etc.) or near
power for fluorescent lighting.
• Avoid routing cable near ADF antenna cable (allow at least a 12-inch separation).

190-00325-01 Revision A
2.7 Installation Approval Considerations for Pressurized Aircraft
Antenna and cable installations on pressurized cabin aircraft require FAA approved installation design
and engineering substantiation data whenever such installations incorporate alteration (penetration) of the
cabin pressure vessel by connector holes and/or mounting arrangements.
For needed engineering support pertaining to the design and approval of such pressurized aircraft antenna
installations, it is recommended that the installer proceed according to any of the following listed
alternatives:
1. Obtain approved antenna installation design data from the aircraft manufacturer.
2. Obtain an FAA approved Supplemental Type Certificate (STC) pertaining to and valid for the
subject antenna installation.
3. Contact the FAA Aircraft Certification Office in the appropriate Region and request identification
of FAA Designated Engineering Representatives (DERs) who are authorized to prepare and
approve the required antenna installation engineering data.
4. Obtain FAA Advisory Circular AC-183C and select (and contact) a DER from the roster of
individuals identified thereunder.
5. Contact an aviation industry organization such as the Aircraft Electronics Association and request
their assistance.
2.8 Electrical Noise

Because the audio panel is a point in the aircraft where signals from many pieces of equipment are
brought together, take care to minimize effects from coupled interference and ground loops.
Coupled interference can creep into audio system interconnecting cables when they are routed near large
AC electric fields, AC voltage sources and pulse equipment (strobes, spark plugs, magnetos, EL displays,
CRTs, etc). Interference can also couple into audio system interconnecting cables by magnetic induction
when they are routed near large AC current-carrying conductors or switched DC equipment (heaters,
solenoids, fans, autopilot servos, etc).
Ground loops are created when there is more than one path in which return currents flow or when signal
returns share the same path as large currents from other equipment. These large currents create
differences in ground potential between the various equipment operating in the aircraft. These differences
in potential can produce an additive effect on audio panel input signals.
The audio panel may “see” the desired input signal plus an unwanted component injected by ground
differentials, a common cause of alternator-related noise. This is the main reason why all audio jacks
should be isolated from ground. Terminating audio shields just at one end eliminates another potential
ground loop injection point.
Single-point grounding cannot be overstressed for the various avionics producing and processing audio
signals. Single-point, in this context, means that the various pieces of equipment share a single common
ground connection back to the airframe. Good aircraft electrical/charging system ground bonding is also
important.
The wiring diagrams and accompanying notes in this manual should be followed closely to minimize
noise effects.

Revision A 190-00325-01
2.9 GMA 347 Mounting
The GMA 347 mounting surface must be capable of providing structural support and electrical bond to
the aircraft to minimize radiated EMI and provide protection from High-Intensity Radiation Fields
(HIRF).
The GMA 347 is mounted using it’s own system rack. Figure 2-1 shows the GMA 347 unit rack.
1 Slide the unit into the rack until the front lobe of the unit touches the rack.
2 Insert a 3/32” hex wrench into the access hole on the faceplate.
3 Turn the hex wrench clockwise until the unit is secured in the rack. Continue turning until
tight. Do not over-tighten the screw.
4 To remove the unit from the rack, turn the hex wrench counterclockwise until it disengages
from the rack.
Figure 2-1. GMA 347 Unit Rack (115-00427-00)

190-00325-01 Revision A

Revision A 190-00325-01
3 INSTALLATION PROCEDURE
3.1 Unpacking Unit
Carefully unpack the equipment and make a visual inspection of the unit for evidence of damage incurred
during shipment. If the unit is damaged, notify the carrier and file a claim. To justify a claim, save the
original shipping container and all packing materials. Do not return the unit to Garmin until the carrier
has authorized the claim.
Retain the original shipping containers for storage. If the original containers are not available, a separate
cardboard container should be prepared that is large enough to accommodate sufficient packing material
to prevent movement of the item within the container.
3.2 Marker Beacon Antenna Installation

Install the marker beacon antenna according to the antenna manufacturer’s instructions and FAA
Advisory Circulars AC 43.13-1B and AC 43.13-2A Chapters 2 and 3, as applicable.
3.3 Marker Beacon Antenna Cable Connectors

The marker beacon antenna cable requires a BNC or similar coax connector on the antenna end. Follow
connector manufacturer instructions for assembly of the antenna connector.
3.4 Electrical Connections

All electrical connections to the GMA 347, including the marker beacon antenna and shield ground, are
made through two 78-pin D-subminiature connectors (see Figure 4-1). Tables in Section 4 define the
electrical characteristics of all input and output signals. Required connector and associated hardware are
supplied in the connector kit (P/N 011-00813-01). See figures in Appendix C for interconnect wiring
diagrams.
CAUTION
Check wiring connections for errors before inserting the GMA 347 into
the rack. Incorrect wiring could cause internal component damage.
Table 3-1. Pin Contact Part Numbers (Hi Density)

78 pin D-Subminiature Connectors (P3471, 3472)
Manufacturer
16 AWG 18 AWG 20 AWG 22-28 AWG
(Power Only) (Power Only)
Garmin P/N 336-00044-01 336-00044-00 336-00044-02 336-00021-00
Military P/N N/A N/A N/A M39029/58-360
AMP N/A N/A N/A 204370-2
Positronic N/A N/A N/A MC8522D
ITT Cannon N/A N/A N/A 030-2042-000

190-00325-01 Revision A
Table 3-2. Recommended Crimp Tools (Hi Density)
16 & 18 & 20 AWG 22-28 AWG
Manufacturer Hand
Positioner Insertion/ Positioner Insertion/
Crimping Tool
Extraction Tool Extraction
(Note 2) Tool
Military P/N M22520/2-01 N/A M81969/1-04 M22520/2-09 M81969/1-04
Positronic 9507 9502-11 M81969/1-04 9502-3 M81969/1-04
ITT Cannon 995-0001-584 N/A N/A 995-0001-739 N/A
AMP 601966-1 N/A 91067-1 601966-6 91067-1
Daniels AFM8 K774 M81969/1-04 K42 M81969/1-04
Astro 615717 N/A M81969/1-04 615725 M81969/1-04
NOTES
1. Non-Garmin part numbers shown are not maintained by Garmin and

consequently are subject to change without notice.
2. Extracting the #16, #18 and #20 contact requires that the expanded wire
barrel be cut off from the contact. It may also be necessary to push the
pin out from the face of the connector when using an extractor due to the
absence of the wire. A new contact must be used when reassembling the
connector.

Revision A 190-00325-01
3.5 Backshell Assembly and D -Subminiature Connectors
The GMA 347 connector kit (011-00813-01) includes two Garmin backshell assemblies. Backshell
connectors give the installer the ability to terminate shield grounds at the backshell housing using the
Shield Block ground kit. The term ‘D-Sub’ (D-Subminiature) connectors have a letter "D" physical
shape. D-Sub refers only to the polarized shell that holds the contacts (pins or sockets) in place. Table
3-3 lists Garmin part numbers for the GMA 347 D-Sub Connectors and the Backshell Assembly.
Table 3-3. Backshell Assembly (011-00812-00)
Figure Ref Description Garmin P/N

1 Cast Housing (From Garmin Backshell kit.) 125-00085-00
2 Shield block 117-00147-xx
3 Screw, 4-40 x.250, FLHP100°, SS/P, Nylon. 211-63234-08
4 Multiple Conductor Shielded Cable As Required
(See Interconnect Diagrams, Appendix C)
5 Shield Termination As Required
6 Braid, Flat (19 – 20 AWG equivalent, tinned As Required
plated copper strands 36 AWG, Circular Mil
Area 1000 – 1300)
7 Shrink Tubing As Required
8 Pins 336-00021-00
9 Ring terminal, #8, insulated, 18-22 AWG, MS25036-149,
14-16 AWG, 10-12 AWG MS25036-153,
MS25036-156
10 Screw, PHP, 8-32x.312", Stainless or Cad MS51957-42,
Plated Steel MS35206-242
11 Split Washer, #8, (.045" compressed MS35338-137,
thickness) Stainless or Cad-plated steel MS35338-42
12 Flat Washer, #8, .032" thick, .174"ID, .375" NAS1149CN832R,
OD, Stainless or Cad Plated Steel NAS1149FN832P
13 Silicon Fusion Tape 249-00114-00
14 Strain Relief 115-00499-xx
15 Screw,4-40x.375,PHP,SS/P,w/Nylon 211-60234-10
16 Lid 115-00500-xx
17 Screw,4-40x.187,FLHP100,SS/P,w/Nylon 211-63234-06

190-00325-01 Revision A
3.5.1 Shield Block Assembly Procedure
The parts for the connector and backshell assembly, GMA 347 installations, are listed in Table 3-3 and
shown in Figure 3-1.
16 15
17
14
13
1
2
3 7
6 5
9
4
12
11
10
Figure 3-1. Shield Block Install onto Backshell Connector Assembly
Table 3-4. Shield Block Components
Backshell Assembly Shield Block

Garmin P/N Garmin P/N
011-00950-04 011-01169-01
(78 Pin High Density)

Revision A 190-00325-01
1. Attach the Shield Block(s) (2) to the backshell (1) by inserting the flathead screws (3) through the
holes on the Shield Block and threading into the tapped holes on the backshell (1). (See Figure 3-1).
The appropriate number of Shield Block kits is included in the GMA 347 connector kit.
Table 3-5. Shielded Cable Preparation
Float Float Ideal Window Window Ideal

Min Max Float Min Max Window
1.5” 2.5” 2.0” 3.0” 5.5” 4.5”
Figure 3-2. Shielded Cable Preparation
2. At one end of a shielded cable (4) measure back a distance between “Window Min” to “Window
Max” (Table 3-5) and cut a window (max size 0.35”) in the jacket to expose the shield. (See Figure
3-2). Use caution when cutting the jacket to avoid damaging the individual braids of the shield.
When dealing with a densely populated connector with many cables it may prove beneficial to
stagger the windows throughout the “Window Min” to “Window Max” range. If staggering is not
needed the “Ideal Window” length is recommended.
Tools needed to Accomplish the Window Cut:

• Coaxial Cable Stripper
• Thermal Stripper
• Sharp Razor Blade
3. Connect a Flat Braid (6) to the shield exposed through the window of the prepared cable assembly
(4). The Flat Braid goes out the front of the termination towards the connector. Do not allow wires
to exit the rear of the termination and loop back towards the connector. (See Figure 3-2). Make this
connection using an approved shield termination technique. Refer to FAA Advisory Circular AC
43.13 as a reference for termination techniques.
Preferred Method, Solder Sleeves:

Slide a solder sleeve (5) onto the prepared cable assembly (4) and connect the Flat Braid (6) to the shield
using a heat gun approved for use with solder sleeves. It may be easier to use a solder sleeve with a pre-
installed Flat Braid versus having to cut a length of Flat Braid to be used. The chosen size of solder
sleeve must accommodate both the number of conductors present in the cable and the Flat Braid (6) to be
attached.
190-00325-01 Revision A
NOTE
Solder Sleeves with pre-installed Flat Braid: A preferred solder sleeve

is the Raychem S03 Series with the thermochromic temperature
indicator. These solder sleeves come with a pre-installed braid and
effectively take the place of items 5 and 6. For detailed instructions on
product use, refer to Raychem installation procedure RCPS 100-70.
Raychem Recommended Heating Tools:

• HL1802E
• AA-400 Super Heater
• CV-1981
• MiniRay
• IR-1759
Individual Solder Sleeves and Flat Braid

Solder Sleeves:
Reference the following MIL-Specs for general solder sleeves:
(M83519/1-1, M83519/1-2, M83519/1-3, M83519/1-4, M83519/1-5).
Flat Braid:
If the preferred Raychem sleeves are not being used, the individual flat braid selected should conform to
ASTMB33 for tinned copper and be made up of 36 AWG strands to form an approximately 19-20 AWG
equivalent flat braid. A circular mil area range of 1000 to 1300 is required. The number of individual
strands in each braid bundle is not specified.
NOTE
Flat Braid as opposed to insulated wire is specified in order to insure

continuing airworthiness by allowing for visual inspection of the
conductor.
Secondary Method, Heat Shrink instead of Solder Sleeves:

Solder a Flat Braid (6) to the shield exposed through the window of the prepared cable assembly (4).
Ensure a solid electrical connection through the use of acceptable soldering practices. Use care to avoid
applying excessive heat that burns through the insulation of the center conductors and shorts the shield to
the signal wire. Slide a minimum 0.75” of Teflon heat shrinkable tubing (5) onto the prepared wire
assembly and shrink using a heat gun. The chosen size of heat shrinkage tubing must accommodate both
the number of conductors present in the cable and the Flat Braid (6) to be attached.

Revision A 190-00325-01
4. At the same end of the shielded cable (4) and ahead of the previous shield termination, strip back
“Float Min” to “Float Max” (Table 3-5) length of jacket and shield to expose the insulated center
conductors. (See Figure 3-2). It may be best to build the “Ideal Float” length optimally.
Preferred Method:
The jacket and shield should be cut off at the same point so no shield is exposed. Slide 0.75” minimum of
Teflon heat shrinkable tubing (7) onto the cable and use a heat gun to shrink the tubing. The chosen size
of heat shrinkage tubing must accommodate the number of conductors present in the cable
Secondary Method:
Leave a max 0.35” of shield extending past the jacket. Fold this 0.35” of shield back over the jacket.
Slide a solder sleeve (7) over the end of the cable and use a heat gun approved for solder sleeves to secure
the connection. The chosen size of solder sleeve must accommodate the number of conductors present in
the cable.
5. Strip back 1/8” of insulation and crimp a pin (8) to each of the conductors in the shielded cable.
6. Insert newly crimped pins and wires into the appropriate connector housing location as specified by
the installation wiring diagrams.
7. Cut the Flat Braid (6) to a length with the addition of a ring terminal that will reach one of the tapped
holes of the Shield Block (2). (See Figure 3-1). An appropriate amount of excess length without
looping should be given to the Flat Braid (6) to allow it to move freely with the wire bundle. Note
that the maximum distance from the backshell allowed for the window splice should keep the Flat
Braid (6) to a worst case length of approximately 4”.
8. Guidelines for terminating the newly cutoff Flat Braid(s) (item 6) with insulated ring terminals (9):
• Each tapped hole on the Shield Block (2) may accommodate only two ring terminals (9).
• It is preferred that only two Flat Braids (6) be terminated per ring terminal. Two Flat Braids per
ring terminal will necessitate the use of a Ring terminal, #8, insulated, 14-16 AWG
(MS25036-153).
• If only a single Flat Braid is left or if only a single Flat Braid is need for this connector, a Ring
terminal, #8, insulated, 18-22 AWG (MS25036-149) can accommodate this single Flat Braid.
• If more braids exist for this connector than two per ring terminal, it is permissible to terminate
three braids per ring terminal. This will necessitate the use of a Ring terminal, #8, insulated,
10-12 AWG (MS25036-156).
• In rare situations where more braids need to be terminated for this connector than three per ring
terminal it is allowable to daisy chain a maximum of two shields together before coming to the
ring terminal. (See Figure 3-3).

190-00325-01 Revision A
Figure 3-3: Daisy Chain Method for Shield Termination
9. Repeat steps 2 through 8 as needed for the remaining shielded cables.
10. Terminate the ring terminals to the Shield Block (2) by placing items on the Pan Head Screw (10) in
the following order: Split Washer (11), Flat Washer (12), first Ring Terminal, second Ring Terminal
if needed, before finally inserting the screw into the tapped holes on the Shield Block. Do not violate
the guidelines presented in Step 8 regarding ring terminals.
11. It is recommended to wrap the cable bundle with Silicone Fusion Tape (13) (GPN: 249-00114-00 or a
similar version) at the point where the backshell strain relief and cast housing will contact the cable
bundle. Note: Choosing to use this tape is at the discretion of the installer.
12. Place the smooth side of the backshell strain relief (14) across the cable bundle and secure using the
three screws (15). Warning: Placing the grooved side of the strain relief across the cable bundle may
risk damage to wires.
13. Attach the cover (16) to the backshell (1) using two screws (17).
7
9
6
Figure 3-4: Parallel Shield Termination

Revision A 190-00325-01
3.5.2 Configuration Module Installation
Table 3-6 lists part numbers for the Configuration Module Kit.
Table 3-6. Configuration Module Kit – 011-00979-00
Item Description Garmin P/N

Configuration Module PCB Board Assembly w/EEPROM 012-00605-00
Cable 4-Conductor Harness 325-00122-00
Crimp Pins #22 AWG (HD) 336-00021-00
Spacer Spacer, Config Module 213-00043-00

190-00325-01 Revision A
3.5.3 Configuration Module Assembly Procedure
Table 3-7. Configuration Module Wire Color Reference Chart
Color Function J3472 Pin

Black Ground 1
Red Vcc 21
Yellow Data 40
White Clock 60
1. Crimp pins (4) onto each wire of the four-conductor wire harness (3). Strip 1/8” of insulation
from each wire prior to crimping.
2. Insert newly crimped pins and wires (3, 4) into the appropriate connector housing (5) location
shown in the figure below.
3. Apply the spacer (2) by wrapping it around the PCB Board (1) making sure to insert the plastic
connector mounted on the board into the hole provided in the spacer.
4. Plug the four-conductor wire harness (3) into the connector on the PCB Board (1).
5. Insert into the backshell (6) recess, PCB Board (1) with pad (2) in position.
6. Attach cover (7) to backshell (6) using screws (8).
Figure 3-5. Configuration Module Installation

Revision A 190-00325-01
3.6 Circuit Breaker Placard
Install a Circuit Breaker Placard labeled Audio Panel, Audio Panel 1 or Audio Panel 2 as appropriate as
indicated in FAA Advisory Circular AC 43.13-2A, Paragraph 27c(4).
3.7 GMA 347 Unit Installation
CAUTION
Do not use excessive force when inserting the GMA 347 into the rack.
This may damage the connectors, unit, and/or unit rack. If heavy
resistance is felt during installation, stop! Remove the GMA 347 and
identify the source of resistance.
For final installation and assembly, refer to the outline and installation drawings shown in Appendix B of
this manual.
1. Assemble the backshell as described in Section 3.5.

2. Connect both backshells to the rear plate using the screws provided in the connector kit.
3. Mount the unit rack to a suitable mounting location on the panel using the provided nutplates.
4. Assemble the rear plate into the GMA 347 unit rack.
5. Insert the GMA 347 into the rack, noting proper orientation as shown on the installation
drawing in Appendix B.
6. Lock the GMA 347 in place using a 3/32 hex wrench.
3.8 Post Installation Configuration and Checkout

Refer to Section 5 for GMA 347 System Configuration.
CAUTION
Check wiring connections for errors before inserting the GMA 347 into
the tray. Incorrect wiring could cause internal component damage.
Except for marker beacon operation, an in-aircraft checkout may be performed in the aircraft on the ramp
with a known good microphone, headset, speaker and avionics receivers.
For testing the marker beacon, use a ramp tester that transmits a 75 MHz marker beacon test signal.
For installation checkout procedures refer to the GMA 347 Pilot’s Guide (190-00325-00) for GMA 347
operation. Verify that every function of the GMA 347 operates correctly.

190-00325-01 Revision A
NOTE
In the following procedural steps outlined below, allow for variations in

configuration settings for the particular unit under test.
3.8.1 Lamp Test

Apply power to the unit by rotating the Pilot’s intercom volume knob clockwise out of the detent.
During power-up, the unit undergoes a self-test, illuminating all panel annunciator lights for
approximately two seconds (between 1/2 and 2 seconds).
Confirm the operation of the GMA 347 internal LED annunciators and marker beacon LED’s. Cover the
photocell with a finger and observe that the LED annunciators dim automatically. Check the front panel
key backlighting and dimming function. Key brightness is controlled with the aircraft radio lights
dimming bus.
3.8.2 Failsafe Operation Check

1. Turn the unit off by rotating the Pilot’s intercom volume knob counter clockwise.
2. Check the failsafe operation by exercising the COM 1 microphone, microphone key and audio
over the headphones. A stereo headset connected to the Pilot headphone jack will provide audio
in the left earphone only.
3. Turn the unit back on to continue testing.
3.8.3 Transceiver Operational Check

1. Perform a ramp test radio check by exercising the installed transceivers, microphone, microphone
key and audio over the headphones and speaker.
2. Verify that communications are loud and clear and PTT operation is correct.
NOTE
Split COM performance varies significantly across installations and is

affected by both the distance between the antennas and the separation of
the tuned frequencies.
3. In appropriate installations, check for Pilot/Copilot microphone operation when using the Split
COM (COM 1/2 key) function.

Revision A 190-00325-01
3.8.4 Intercom System (ICS) Check
NOTE
If a monaural headset is plugged into any stereo phone jack position, no

damage will occur to the GMA 347. In the case of plugging a monaural
headset into any passenger position, any stereo listener will lose one
channel when another passenger plugs in a monaural headset.
1. Set the intercom to the ALL mode (Pilot and Copilot LED’s off.)
2. Plug in headsets at each ICS position.
3. Adjust squelch and volume for each position and verify that the ICS is working properly.
4. Check Pilot and Copilot ICS positions for isolation and proper operation of volume and squelch
controls.
5. Press and hold the SPKR key for two seconds. Verify that the SPKR key annunciator flashes,
indicating the PA mode, and that microphone audio is heard over the speaker.
3.8.5 Aircraft Receivers Check

1. Select the audio source for each avionics unit installed in the aircraft and check for audio over the
headsets.
2. Check for Pilot/Copilot audio isolation when pressing the Split COM (COM 1/2) key.
3. Press the SPKR key and verify that any selected audio is heard over the speaker.
3.8.6 Clearance Recording Check

1. Allow COM 1 receiver to operate for at least two and one half (2.5) minutes of active operation.
2. Press the PLAY key once to play back the latest recorded memory block of COM 1 audio.
3. Press the PLAY key again to play the previous memory block of COM 1 audio. Continue
stepping backward into the memory blocks until listening to the first block of audio. A total of
2.5 minutes of audio is recorded.
4. Verify that after playing back the full 2.5 minutes of stored audio, that the playback system audio
stops.
3.8.7 Music System Check

1. Set the intercom to the ALL mode (Pilot and Copilot LED’s off.)
2. Connect a stereo audio source to MUSIC 1. Verify that stereo audio is heard over the Pilot and
Copilot headset positions.
3. Tune a station on COM 1 and verify that the sound is muted by active COM 1 audio (break
squelch on COM 1 if necessary).
4. Connect a stereo music source to MUSIC 2. Verify that stereo audio is heard in the passenger
headsets.

190-00325-01 Revision A
3.8.8 Flight Check
CAUTION
Be sure to check all aircraft control movements before flight is attempted

to insure that the wiring harness does not touch any moving part. Verify
proper operation of the marker beacon during a flight test under VFR
conditions.
Perform a flight test after installing the unit to ensure satisfactory performance of the audio and marker
beacon receiver functions. Verify proper operation of the marker lamps and marker audio, including the
marker audio mute function. Check proper operation of the sensitivity selection, using the SENS key, by
flying towards the outer marker (OM) position initially using HI sensitivity. When the OM audio is just
barely audible in the headset, switching to LO sensitivity should reduce or eliminate the audio.
This completes the in-aircraft post installation checkout.

Revision A 190-00325-01
4 SYSTEM INTERCONNECTS
NOTE
When installations that have a Garmin GMA 340 audio panel are being
upgraded to a GMA 347, refer to figure C-5 in appendix C for a pin-to-
pin comparison of the two units.
4.1 Connector Description

The GMA 347 has two 78-pin connectors located at the rear of the unit designated P3471 and P3472.
P3471 and P3472 are clearly marked on the back of the rack. P3471 and P3472 pins are configured as
shown in the following illustration:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Figure 4-1. Backshell Rear Connector Plate
60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Figure 4-2. Rear Connectors J3471 and J3472, Viewed From Back of Unit
4.2 Connectors J3471 and J3472

J3471 and J3472 pin assignments are given in Tables 4-1 and 4-2.
Following the pin assignment table, additional tables group pin connections by function.
An asterisk (*) following a signal name denotes that the signal is an Active Low, requiring a ground to
activate.

190-00325-01 Revision A
Table 4-1. J3471 Pin Assignments
Pin Pin Name I/O
1 FAIL SAFE WARN AUDIO IN In
2 RESERVED --
3 TEL RINGER AUDIO IN HI In
4 TEL RINGER AUDIO IN LO In
5 RESERVED --
6 ON-SIDE NAV AUDIO IN HI In
7 ON-SIDE COM AUDIO IN HI In
8 ON-SIDE COM AUDIO LO I/O
9 PILOT HEADSET AUDIO OUT LEFT Out
10 PILOT HEADSET AUDIO OUT RIGHT Out
11 PILOT HEADSET AUDIO OUT LO Out
12 CROSS-SIDE COM AUDIO IN HI In
13 CROSS-SIDE COM AUDIO LO I/O
14 CROSS-SIDE NAV AUDIO IN HI In
15 DME AUDIO IN HI In
16 DME AUDIO IN LO In
17 MUSIC IN 1 LEFT In
18 MUSIC IN 1 RIGHT In
19 UNSWITCHED AUDIO IN 1 HI In
21 RESERVED --
22 RESERVED --
23 TEL MIC AUDIO OUT HI Out
24 PASS ICS KEY* In
25 ON-SIDE NAV AUDIO IN LO In
26 ON-SIDE COM MIC AUDIO OUT HI Out
27 ON-SIDE COM MIC KEY* Out
28 PILOT MIC AUDIO IN HI In
29 PILOT MIC KEY* IN In
30 PILOT MIC IN LO In
31 PILOT ICS KEY* In
32 CROSS-SIDE COM MIC AUDIO OUT HI Out
33 CROSS-SIDE COM MIC KEY* Out
34 CROSS-SIDE NAV AUDIO IN LO In
35 ADF AUDIO IN HI In
36 ADF AUDIO IN LO In
37 MUSIC IN 1 LO In
* Denotes Active Low (Ground to activate).

Revision A 190-00325-01
Table 4-1. J3471 Pin Assignments (Continued)
Pin Pin Name I/O
39 UNSWITCHED AUDIO IN LO In
40 RESERVED --
41 RESERVED --
42 TEL AUDIO IN HI In
43 TEL AUDIO IN LO In
44 PASS 3 MIC AUDIO IN HI In
45 PASS 3 MIC AUDIO IN LO In
48 PASS HEADSET AUDIO OUT LO Out
49 COPILOT MIC AUDIO IN HI In
50 COPILOT MIC KEY* IN In
51 COPILOT MIC IN LO In
52 COPILOT ICS KEY* In
53 RESERVED --
54 ALTITUDE WARN AUDIO IN HI In
55 ALTITUDE WARN AUDIO IN LO In
58 COM 3 AUDIO IN HI In
59 COM 3 AUDIO LO I/O
60 RESERVED --
61 RESERVED --
62 TEL MIC AUDIO OUT LO Out
67 PASS HEADSET AUDIO OUT LEFT Out
68 PASS HEADSET AUDIO OUT RIGHT Out
69 COPILOT HEADSET AUDIO OUT LEFT Out
70 COPILOT HEADSET AUDIO OUT RIGHT Out
71 COPILOT HEADSET AUDIO OUT LO Out
72 RESERVED --
73 RESERVED --
74 AUX AUDIO IN HI In
75 AUX AUDIO IN LO In
76 MUSIC IN 2 LO In
77 COM 3 MIC AUDIO OUT HI Out
78 COM 3 MIC KEY* Out

190-00325-01 Revision A
Table 4-2. J3472 Pin Assignments
Pin Pin Name I/O
1 CONFIG MODULE GROUND --
2 RESERVED --
3 PROGRAM GROUND --
4 RECORDER PLAY* In
5 PROGRAM GROUND --
6 RS-232 OUT 1 Out
7 RS-232 IN 1 In
8 RESERVED --
9 RESERVED --
10 RESERVED --
11 PROGRAM GROUND --
12 RESERVED --
13 RESERVED --
14 POWER GROUND --
15 RESERVED --
16 POWER GROUND --
17 COM SWAP* In
19 RESERVED --
20 RESERVED --
21 CONFIG MODULE POWER OUT Out
22 RESERVED --
24 RECORDER OFF SELECT* In
26 AUX SOURCE SELECT* In
27 RESERVED --
28 RESERVED --
29 RESERVED --
30 AIRCRAFT POWER 2 In
31 RESERVED --
33 RESERVED --
34 MIDDLE MARKER SENSE Out
35 RESERVED Out
36 RESERVED --
37 GROUND RETURN --

Revision A 190-00325-01
Table 4-2. J3472 Pin Assignments (Continued)
Pin Pin Name I/O
38 RS-232 OUT 2 Out
39 RS-232 IN 2 In
40 CONFIG MODULE DATA I/O
41 SPEAKER AUDIO OUT LO Out
42 SPEAKER AUDIO OUT HI Out
43 RESERVED --
45 RESERVED --
47 RESERVED --
48 RESERVED --
49 RESERVED --
50 RESERVED --
51 14 V LIGHTING HI In
52 28 V LIGHTING HI In
54 RESERVED --
56 RESERVED --
57 GROUND RETURN --
58 RESERVED --
59 MARKER ANTENNA LO In
60 CONFIG MODULE CLOCK Out
61 RESERVED --
62 RESERVED --
63 RESERVED --
64 PA MUTE* OUT Out
65 TEL DISCRETE RINGER* In
66 RESERVED --
68 RESERVED --
69 POWER GROUND --
70 RESERVED --
71 POWER GROUND --
72 RESERVED --
73 RESERVED --
74 AIRWAY/INNER MARKER EXT LAMP OUT Out
75 MIDDLE MARKER EXT LAMP OUT Out
76 OUTER MARKER EXT LAMP OUT Out
77 RESERVED --
78 MARKER ANTENNA HI In

190-00325-01 Revision A
4.3 J3472 Connector Pin Assignments
This section covers the pin connections of J3472 only.
4.3.1 Aircraft Power and Lighting

Power Input requirements and Lighting Bus inputs are listed in the following tables. The power-input
pins accept 11-33 Vdc. AIRCRAFT POWER 2 is for connecting to an alternate power source, such as on
aircraft with two electrical buses. Refer to Figure C-1 for power interconnections.
Table 4-3. Aircraft Power Pin Assignments, J3472
Pin Pin Name Description I/O
53 AIRCRAFT POWER 1 Unit power In
69 POWER GROUND Aircraft ground --
4.3.2 Lighting Bus

The GMA 347 can be configured to track a 28 Vdc or 14 Vdc lighting bus using these inputs. Refer to
Figure C-1 for lighting interconnections.
Table 4-4. Aircraft Lighting Pin Assignments, J3472
51 14 V LIGHTING HI 14V Backlighting input, 0 to 14 Vdc In
52 28 V LIGHTING HI 28V Backlighting input, 0 to 28 Vdc In

Revision A 190-00325-01
4.3.3 RS -232 Serial Input/Output
Table 4-5. RS-232 Pin Assignments, J3472

6 RS-232 OUT 1 Output level greater than ±5 Volts Out
7 RS-232 IN 1 Input level up to ±25 volts In
38 RS-232 OUT 2 Output level greater than ±5 Volts Out
39 RS-232 IN 2 Input with level up to ±25 volts In
The RS-232 outputs conform to EIA/TIA-232C with an output voltage swing of at least ±5 V when
driving a standard RS-232 load. The RS-232 IN/OUT 1 connections are used to upload configuration
data into the unit. The unit is configured out of the aircraft, before final installation. Refer to Section 5
for configuration instructions.
Figure 4-3. GMA 347 Configuration Upload Connections

190-00325-01 Revision A
4.3.4 Marker Beacon Functions
Marker Beacon connections are listed in the following table. The antenna input is connected to pins 78
(HI or Center Conductor) and 59 (LO or Shield).
Table 4-6. Marker Beacon Pin Assignments, J3472
34 MIDDLE MARKER SENSE 2.5-8 Vdc into 4.7 k Out
AIRWAY/INNER MARKER EXT
74 MKR I-HI white 2.5-8 Vdc into 56 Out
LAMP OUT
MKR M-HI amber. 2.5-8 Vdc into
75 MIDDLE MARKER EXT LAMP OUT Out
56
76 OUTER MARKER EXT LAMP OUT MKR O-HI blue. 2.5-8 Vdc into 56 Out
78 MARKER ANTENNA HI Marker antenna input, 50 In
59 MARKER ANTENNA LO Ground reference for pin 78 --
4.3.5 Installation Selection Inputs

The following table shows the Installation Selection Inputs of J3472. The selection inputs have an input
and a program ground. When the input is grounded, the input function is selected.
Table 4-7. Installation Selection Inputs Pin Assignments, J3472
4 RECORDER PLAY* An external pushbutton switch activates voice In
5 PROGRAM GROUND recorder playback. --
17 COM SWAP* When enabled, COM 1 and COM 2 are In
swapped. This is used with a switch tied to
18 PROGRAM GROUND ground for momentary operation. --
24 RECORDER OFF SELECT* In
When enabled, the voice recorder is disabled.
This input is used for an external switch tied to
26 AUXILIARY SOURCE SELECT* In
ground to control the auxiliary audio.
This input is for use with a cellular phone with a
65 TEL DISCRETE RINGER* In
digital output.

Revision A 190-00325-01
4.3.6 External Configuration Module
The configuration module contains an I2C temp sensor and EEPROM. The configuration module is
located in the connector backshell. The configuration module stores a backup of the unit configuration.
Table 4-8. External Configuration Module Pin Assignments, J3472

1 Configuration Module Ground Ground --
21 Configuration Module Power +3.3 VDC In
40 Configuration Module Data Bi-directional data line In/Out
60 Configuration Module Clock Signal used to clock data input\output Out
4.3.7 Speaker
The speaker output is capable of driving up to 10 Watts into a 4 ȍ or 8 ȍ speaker.
Table 4-9. Speaker Pin Assignments, J3472

41 SPEAKER AUDIO OUT LO Ground reference for speaker audio --
42 SPEAKER AUDIO OUT HI Speaker audio output Out
4.3.8 PA MUTE
PA MUTE is an output that when pulled low is active. It is used to trigger the mute function on
an external PA system.
Table 4-10. PA MUTE Pin Assignments, J3472
64 PA MUTE* OUT Output capable of sinking 500 mA Out

190-00325-01 Revision A
4.4 J3471 Connector Pin Assignments
This section covers the pin connections of J3471 only.
4.4.1 Mic Audio Inputs and Mic Keys
Table 4-11. Mic Audio Inputs and Mic Key Pin Assignments, J3471
29 PILOT MIC KEY* IN Enables audio into the respective In
50 COPILOT MIC KEY* IN transceiver unit In
28 PILOT MIC AUDIO IN HI In
Pilot Mic audio input and ground reference
30 PILOT MIC IN LO --
49 COPILOT MIC AUDIO IN HI In
Copilot Mic audio input and ground
51 COPILOT MIC IN LO reference --
46 PASS 1 MIC AUDIO IN HI Passenger 1 Mic audio and ground In
47 PASS 1 MIC AUDIO IN LO reference --
4.4.2 ICS Keys
Table 4-12. ICS Key Pin Assignments, J3471

31 PILOT ICS KEY* In
52 COPILOT ICS KEY* Enables audio into the intercom system In
24 PASS ICS KEY* In

Revision A 190-00325-01
4.4.3 Com Audio and Mic Keys
Table 4-13. Com Audio and Mic Keys Pin Assignments, J3471
27 ON-SIDE COM MIC KEY* In
Enables audio into the respective
33 CROSS-SIDE COM MIC KEY* transceiver unit In
78 COM 3 MIC KEY* In
7 ON-SIDE COM AUDIO IN HI Com 1 audio input In
26 ON-SIDE COM MIC AUDIO OUT HI Com 1 audio output Out
8 ON-SIDE COM AUDIO LO Ground reference for Com 1 audio --
12 CROSS-SIDE COM AUDIO IN HI Com 2 audio input In
32 CROSS-SIDE COM MIC AUDIO OUT HI Com 2 audio output Out
13 CROSS-SIDE COM AUDIO LO Ground reference for Com 2 audio --
58 COM 3 AUDIO HI Com 3 audio input In
77 COM 3 MIC AUDIO OUT HI Com 3 audio output Out
59 COM 3 AUDIO LO Ground reference for Com 3 audio --
4.4.4 Nav Audio
Table 4-14. Nav Audio Pin Assignments, J3471

6 ON-SIDE NAV AUDIO IN HI Nav 1 audio input In
25 ON-SIDE NAV AUDIO IN LO Nav 1 ground reference --
14 CROSS-SIDE NAV AUDIO IN HI Nav 2 audio input In
34 CROSS-SIDE NAV AUDIO IN LO Nav 2 ground reference --
4.4.5 Headset Outputs
Table 4-15. Headset Outputs Pin Assignments, J3471

9 PILOT HEADSET AUDIO OUT LEFT Out
Pilot headset audio output
10 PILOT HEADSET AUDIO OUT RIGHT Out
11 PILOT HEADSET AUDIO OUT LO Ground reference for pilot headset --
69 COPILOT HEADSET AUDIO OUT LEFT Out
Copilot headset audio output
70 COPILOT HEADSET AUDIO OUT RIGHT Out
71 COPILOT HEADSET AUDIO OUT LO Ground reference for copilot headset --
67 PASS HEADSET AUDIO OUT LEFT Out
Passenger headset audio output
68 PASS HEADSET AUDIO OUT RIGHT Out
Ground reference for passenger
48 PASS HEADSET AUDIO OUT LO --
headset

190-00325-01 Revision A
4.4.6 Music Inputs
Table 4-16. Music Inputs Pin Assignments, J3471

Music 1 input
37 MUSIC IN 1 LO Ground reference for music 1 --
Music 2 input
76 MUSIC IN 2 LO Ground reference for music 2 --
4.4.7 Unswitched Audio Inputs
Table 4-17. Unswitched Audio Inputs Pin Assignments, J3471

20 UNSWITCHED AUDIO IN 2 HI Unswitched audio inputs In
39 UNSWITCHED AUDIO IN LO Ground reference for unswitched audio --
54 ALTITUDE WARN AUDIO IN HI Unmuted/unswitched input In
55 ALTITUDE WARN AUDIO IN LO Ground reference for altitude warning --
4.4.8 Telephone I/O
Table 4-18. Telephone Inputs/Outputs Pin Assignments, J3471

3 TEL RINGER AUDIO IN HI Ringtone audio input In
Ground reference for telephone ringer
4 TEL RINGER AUDIO IN LO In
audio input
23 TEL MIC AUDIO OUT HI Transmitted telephone audio output Out
62 TEL MIC AUDIO OUT LO Ground reference for telephone Mic audio --
42 TEL AUDIO IN HI Received telephone audio input In
43 TEL AUDIO IN LO Ground reference for telephone input --

Revision A 190-00325-01
4.4.9 AUX, DME and ADF Audio
Table 4-19. AUX, DME and ADF Audio Pin Assignments, J3471
74 AUX AUDIO IN HI Extra switched audio input In
75 AUX AUDIO IN LO Ground reference for extra switched audio input --
15 DME AUDIO IN HI Distance measuring equipment audio input In
16 DME AUDIO IN LO Ground reference for DME audio input --
35 ADF AUDIO IN HI Automatic direction finder audio input In
Ground reference for automatic direction finder
36 ADF AUDIO IN LO --
audio input
4.4.10 Failsafe Audio
Table 4-20. Failsafe Audio Pin Assignments, J3471

1
Audio summed to the pilots headset left In
FAIL SAFE WARN AUDIO IN
and COM 1 when power fails

190-00325-01 Revision A

Revision A 190-00325-01
5 POST INSTALLATION CONFIGURATION AND CHECKOUT
PROCEDURE
5.1 Post Installation Configuration Harness
Refer to figure 4-3 for GMA 347 Configuration Upload Connections.
5.2 Program Information
Garmin Product GMA 347 Configuration Tool

Used for: GMA 347, GMA 347H, GMA 347 2ADF
Program Archive 006-A0115-00
File Name GMA_CONFIG.EXE
GMA_CONFIG.EXE version at time of this document 2.02
5.3 GMA Configuration Tool Version
NOTE
To find the version of the GMA Configuration Tool, right click anywhere along the top
of the GMA Configuration Tool window and choose “About GMA Configuration Tool”.
See Figure 5-1.
Figure 5-1 About GMA Config Tool
5.4 Configuration Tool Introduction
References to the GMA 347 throughout this document apply to all versions of the GMA 347 unit types,
the GMA 347, GMA 347H, and the GMA 347 2ADF.
The GMA Configuration Tool, GPN 006-A0115-00, is used to configure the GMA 347 through a PC
serial port. The GMA Configuration Tool allows the ability to send updated configuration information
and upload SYSTEM or BOOT BLOCK Hex file code to a GMA 347 via a PC’s RS-232 COM port. The
application can also be used to query the GMA 347 for its current configuration information. Figure 5-2
shows the configurations that can be altered. Each configuration item has a SET value and an ACTIVE
value. The ACTIVE value is what the unit currently has stored, and the SET value is used to change the
current ACTIVE state.

190-00325-01 Revision A
The Configuration Tool program will show the Hardware Unit type as being a GMA 347, the current
system Software Version, the Software Part Number, and the Product Serial Number.
Figure 5-2 GMA Configuration Tool Screen
5.5 Connect and Disconnect Buttons
When the GMA Configuration Tool is first opened, all available COM ports will continuously be queried
until a connection is made with a GMA 347 (Figure 5-3). All SET boxes will become editable and the
product information will appear in place of the “No Connection” message once the initial connection is
made.
Figure 5-3 Connecting to the GMA 347

Revision A 190-00325-01
If the user presses the Disconnect button after an initial connection is made with the GMA 347, the
Connect button will replace the Disconnect button. After the Connect button is pressed the application
will behave similarly to initial startup in that it will continuously try to connect to a GMA 347 on COM
ports 1 – 10 until successful.
If a GMA 347 is connected to the PC COM port, the Disconnect button will be visible above the Apply
button. Pressing the Disconnect button causes the GMA 347 Configuration Tool to disconnect from the
GMA 347 and the Connect button will have to be pressed to reconnect.
NOTE
If there is a connection between the PC and the GMA 347 and the connection gets
interrupted for more than five seconds (either by loss of power to the GMA 347 or a
disconnected data cable), the effect will be identical to pressing the Disconnect button.
5.5.1 Save and Exit Buttons

The Save and Exit button will apply the SET settings and will close the Configuration Tool.
5.5.2 Cancel Button

The Cancel button will NOT apply the SET settings and will close the Configuration Tool.
5.5.3 Apply Button

The Apply button will apply the SET settings and the Configuration Tool will remain open.
5.5.4 Upload Button

The Upload button is used to perform a system or boot block code upload.
5.5.5 Load Config and Save Config Buttons

The Load Config option will load settings from a configuration file into the GMA 347. The data format
of the config file is shown in the CONFIG EXAMPLE at the end of this document. The config file
format should never be changed, only the values that follow the equals (=) signs.
If values entered are not valid as specified in the VALID DATA RANGES section at the end of this
document, the incorrect value will be replaced with a default value.
For options that have a data range of –31 to 31 the Load Config operation will accept a two digit number
with or without a negative sign (Ex…. -15, 15). If characters are entered after a number (i.e. 8c), the 8
will be the only value output to the application’s window. If only characters are entered, a zero (0) will
be output to the display for that value.
For options that use a 0 or 1 for the config, a 0 represents NOT SET, and a 1 represents that the option
will be SET.
The Save Config button queries the GMA 347 for the current config values, then stores those values in a
“.ini” file regardless of whether or not the SET box is different than the ACTIVE box. The default file
type is “.ini”. When saving the config file leave the file type as “.ini”. This will make it easier when
loading the Config using the Load Config button (since the file type is defaulted to “.ini”).

190-00325-01 Revision A
5.6 Configuration Tool Settings
5.6.1 Numeric Adjustments
Volume and threshold levels can be adjusted from –31 to +31. To change the level use the computer
mouse and click in the “SET” field to be modified, enter a number within the range and hit the enter key.
Or, use the mouse and click the up or down arrow in the field to change the value. After changing a
value, click the Apply button at the bottom right corner of the GMA 347 Configuration Tool. After
clicking the Apply button, the “ACTIVE” field will be updated to show the current settings.
5.6.2 Configuration Settings

Clicking in the “SET” field of an enable/disable (checkbox) option will modify the option. The
configuration of the enable/disable item will become “ACTIVE” in the unit upon clicking the Apply
button. Modifying a numeric value in the “SET” field and clicking the Apply button will make the
numeric value “ACTIVE” in the unit
5.6.3 Configuration Options

Each setting will have a SET value and an ACTIVE value shown on the GMA 347 Configuration Tool.
The SET values can be altered. The ACTIVE values represent the value that the unit currently has stored.
5.6.4 Headset Volume
MUSIC #1 Volume adjustments can be made by adjusting the volume up or

MUSIC #2 down for each of the listed audio selections. Increasing the
UNSWITCHED IN #1 number will increase the volume and decreasing the number will
UNSWITCHED IN #2 decrease the volume.
UNSWITCHED IN #3
ALTITUDE WARNING
5.6.5 Master Squelch
The sensitivity level of the Master Squelch can be adjusted up or down.

Increasing the number will increase the receiver sensitivity (decrease
SENSITIVITY VALUE the amount of audio required to break squelch). Decreasing the
number will decrease the receiver sensitivity (increase the amount of
audio required to break squelch).
5.6.6 Speaker Volume
Volume adjustments can be made by adjusting the volume up or

CREW AUDIO down. Increasing the number will increase the volume and
decreasing the number will decrease the volume.
Volume adjustments can be made by adjusting the volume up or
PILOT MIC TO SPKR
down. Increasing the number will increase the volume and
COPILOT MIC TO SPKR decreasing the number will decrease the volume.

Revision A 190-00325-01
5.7 Marker Beacon
HI SENSE Both High and Low sensitivity threshold numbers can be adjusted up or
THRESHOLD down. Increasing the number will decrease the threshold required for a
LO SENSE lamp on condition. Decreasing the number will increase the threshold
THRESHOLD required for a lamp on condition.
Volume adjustments can be made by adjusting the volume up or down.
VOLUME Increasing the number will increase the volume and decreasing the
number will decrease the volume.
5.8 Keypad Annunciators
DISABLE COM3 Each of the following keys can be disabled so that pushing the
DISABLE TEL associated button will do nothing.
DISABLE DME
DISABLE ADF
DISABLE SPLIT COM
DISABLE PLAY
DISABLE PA
DISABLE SPKR
5.9 Configuration Inputs
MASQ INHIBIT Setting this option will turn off the Master Squelch.
ICS MUTE Setting this option will mute Music 1 during ICS activity.
INTERNAL Setting this option will provide sidetone for installations using
SIDETONE transceivers that do not provide sidetone.
Setting this option will mute all secondary COM audio when transmitting
MUTE AUDIO ON TX
audio on the primary COM.
Setting this option will mute all secondary COM audio when receiving
MUTE AUDIO ON RX
audio on the primary COM.
Setting this option will record COM 2 audio on the voice recorder when
RECORD COM2
the unit is in Split COM mode.

190-00325-01 Revision A
5.10 Code Upload
To upload code, first select the type of code to be loaded into the unit. SYS is SYSTEM code and BB is
BOOT BLOCK code. If no selection is made by using the mouse to select a radio button and “Upload” is
selected, Figure 5-4 will appear to indicate a selection must be made to specify the code type to be loaded.
Figure 5-4 Radio Button Not Chosen and Upload Selected
After selecting the type of code to load, Figure 5-5 will open for the Hex file of the software to be
selected.
Figure 5-5 File Selection
Select the Hex file to upload and click on Open. If boot code is selected while attempting to do a system
code upload, Figure 5-6 will warn about the possible user error. Clicking cancel will allow the correct
Hex file to be selected.
Figure 5-6 Wrong Hex File Selected (Selecting Boot Code for System Code Upload)
If system code is selected for a boot block upload, Figure 5-7 will warn that the wrong hex file has been
selected.

Revision A 190-00325-01
Figure 5-7 Wrong Hex File Selected (Selecting System Code for Boot Code Upload)
Selecting the correct Hex file and clicking Open will start the code upload. After the correct Hex file is
selected, Figure 5-8 will open with the title “Erasing Flash…”. In approximately 20 seconds the window
displayed in Figure 5-8 will turn into the window displayed in Figure 5-9. The “Uploading Flash…”
window shows the percentage of code uploaded, the time remaining, and the time elapsed
Flash being erased
Figure 5-8 Erasing Flash
Code Upload window after flash has been erased
Figure 5-9 Uploading Flash
If the Cancel button is clicked while the code is being uploaded, Figure 5-10 will warn that a code upload
is in progress. Click No to resume the code upload. Click Yes to cancel the code upload.
Figure 5-10 Canceling a Code Upload
If the code upload is cancelled, Figure 5-11 will show that the code upload failed.

190-00325-01 Revision A
NOTE
If this failure occurs DO NOT turn the unit power off. Reselect the code to be uploaded and
attempt the code upload again.
Figure 5-11 Code Upload Failed
When the code upload is finished, Figure 5-12 will appear to indicate code upload completion.
Figure 5-12 Code Upload Complete

Revision A 190-00325-01
5.11 Configuration Example
hs_music1_vol=0
hs_music2_vol=0
hs_unswch1_vol=0
hs_unswch2_vol=0
hs_unswch3_vol=0
hs_altwarn_vol=0
spkr_crew_vol=0
mkr_vol=0
dsbl_spkr=0
pil_mic_vol=0
cop_mic_vol=0
master_sql_level=0
lo_sens_thrd=0
hi_sens_thrd=0
masq_inht=0
ics_mute=0
intl_sidetone=0
dsbl_play=0
dsbl_pa=0
mute_tx=0
mute_rx=0
dsbl_split_com=0
rec_com2=0
dsbl_com3=0
dsbl_tel=0
dsbl_dme=0
dsbl_adf=0

190-00325-01 Revision A
5.12 Valid Data Ranges
DESCRIPTION VALID DATA

Headset music 1 volume -31 – 31
Headset music 2 volume -31 – 31
Headset unswitched 1 volume -31 – 31
Headset altitude warning volume -31 – 31
Speaker crew audio volume -31 – 31
Headset marker beacon volume -31 – 31
Disable speaker 0 or 1
Pilot mic to speaker volume -31 – 31
CoPilot mic to speaker volume -31 – 31
Master squelch sensitivity level -31 – 31
LO sense threshold -31 – 31
HI sense threshold -31 – 31
MASQ inhibit 0 or 1
ICS mute 0 or 1
Select internal sidetone 0 or 1
Disable play 0 or 1
Disable PA 0 or 1
Mute audio on TX 0 or 1
Mute audio on RX 0 or 1
Disable split com 0 or 1
Select to record COM 2 0 or 1
Disable COM3 annunciator 0 or 1
Disable TEL annunciator 0 or 1
Disable DME annunciator 0 or 1
Disable ADF annunciator 0 or 1

Revision A 190-00325-01
APPENDIX A CERTIFICATION DOCUMENTS
A.1 Airworthiness Approval
Airworthiness approval of the GMA 347 may be acquired by the use of FAA Form 337. The following is
provided as sample wording for Form 337, when replacing an existing audio panel with a Garmin
GMA 347 Audio Panel. Modify appropriately for new installations.
Removed the existing [model] audio panel and replaced with a Garmin GMA 347 Audio Panel
and Marker Beacon, P/N 010-00275-xx in [aircraft location].
The GMA 347 is FAA TSO Approved to C50c and C35d Class A. The GMA 347 meets RTCA
DO-160D environmental qualifications for this installation. See Section 1 of the GMA 347
Installation Manual.
Installed in accordance with the Garmin GMA 347 Installation Manual 190-00325-01, Revision
[ ], and AC 43.13-2, Chapters 2, and 3.
The GMA 347 interfaces with existing aircraft radios per the Installation Manual instructions.
The Installation Manual provides detailed installation instructions and wiring diagrams (Sections
2, 3, and 4 and Appendices B and C).
Power is supplied to the GMA 347 through an existing [AUDIO 5] 5-Amp circuit breaker that
was previously used by the existing audio panel. The net electrical load is unchanged.
Aircraft equipment list, weights and balance amended. Compass compensation checked and
found to conform to applicable regulations.
A.2 Continued Airworthiness
Maintenance of the GMA 347 is “on condition” only. Refer to the GMA 347 Maintenance Manual
(Garmin P/N 190-00325-02). Periodic maintenance of the GMA 347 is not required.
The following sample Instructions for Continued Airworthiness (ICA) provides assistance in preparing
ICA for the Garmin GMA 347 unit installation as part of an FAA Type Certificate (TC) or Supplemental
Type Certificate (STC) project, to comply with 14 CFR §§23.1529 and 25.1529, “Instructions for
Continued Airworthiness”.
Items that may vary by aircraft make and model are shown in braces (“[ ]”) and should be filled in as
appropriate. Some of the checklist items do not apply, in which case they should be marked “N/A” (Not
Applicable).
GMA 347 Installation Manual Page A-1

190-00325-01 Revision A
Instructions For Continued Airworthiness, Garmin GMA 347 Audio Panel In An
[Aircraft Make And Model]
1. Introduction
[Aircraft that has been altered: Registration (N-) number, Make, Model and Serial Number]
Content, Scope,
Purpose and Arrangement: This document identifies the Instructions for Continued Airworthiness
for a Garmin GMA 347 installed in an [aircraft make and model].
Applicability: Applies to a Garmin GMA 347 installed in an [aircraft make and
model].
Definitions/Abbreviations: None, N/A.
Precautions: None, N/A.
Units of Measurement: None, N/A.
Referenced Publications: Garmin GMA 347 Audio Panel Installation Manual,
P/N 190-00325-01
Garmin GMA 347 Audio Panel Maintenance Manual,
P/N 190-00325-02
Garmin GMA 347 Audio Panel Pilot’s Guide, P/N 190-00325-00
STC/TC # [applicable STC/TC number for the specific aircraft
installation]
Distribution: This document should be a permanent aircraft record.
2. Description of the System

Garmin GMA 347 Audio Panel with interface to external transceivers and [include other
equipment/systems as appropriate]. Refer to Appendix C and Figures C-1 through C-5 of this
manual for interconnect information. Refer to aircraft manufacturer approved interconnect for
actual installation. Marker Beacon antenna installation, removal and replacement should be in
accordance with applicable provisions of AC 43.13-1B and AC 43.13-2A.
3. Control, Operation Information

Refer to the GMA 347 Audio Panel Pilot’s Guide, P/N 190-00325-00.
4. Servicing Information
N/A
5. Maintenance Instructions
Maintenance of the GMA 347 Audio Panel is ‘on condition’ only. Periodic maintenance is not
required. Refer to the GMA 347 Audio Panel Maintenance Manual.
6. Troubleshooting Information
Refer to the GMA 347 Audio Panel Maintenance Manual.
7. Removal and Replacement Information

Refer to Sections 2 and 3 of the GMA 347 Audio Panel Installation Manual. If the unit is removed
and reinstalled, a functional check of the equipment should be conducted.
Page A-2 GMA 347 Installation Manual

Revision A 190-00325-01
8. Diagrams
Refer to Appendices B and C of the GMA 347 Audio Panel Installation Manual for installation
drawings and interconnect examples.
9. Special Inspection Requirements

N/A
10. Application of Protective Treatments

N/A
11. Data: Relative to Structural Fasteners

GMA 347, antenna and appropriate mounting hardware installation, removal and replacement
should be in accordance with applicable provisions of AC 43.13-1B and AC 43.13-2A.
12. Special Tools

N/A
13. This Section is for Commuter Category Aircraft Only

A. Electrical loads: Refer to Sections 1 and 4 of the GMA 347 Audio Panel Installation Manual.
B. Methods of balancing flight controls: N/A.
C. Identification of primary and secondary structures: N/A.
D. Special repair methods applicable to the airplane: Antenna installation, removal, and
replacement should be in accordance with applicable provisions of AC 43.13-1B and AC 43.13-2A.
14. Overhaul Period

No additional overhaul time limitations.
15. Airworthiness Limitation Section

N/A.
A.3 Environmental Qualification Form, GMA 347 Audio Panel

The following pages are copies of the Environmental Qualification Forms for the Garmin GMA 347
Audio Panel (005-00155-79), provided for reference only.

190-00325-01 Revision A
Figure A-1. GMA 347 Environmental Qualification Form (Sheet 1 of 3)

Revision A 190-00325-01

190-00325-01 Revision A

Revision A 190-00325-01
1.30 33.0 1.59 40.5
6.29 159.8 6.30 160.0
3.15 80.0
.13 3.2
3.65 92.7
6.39 162.4
7.79 197.8
.35 8.9
.65 16.5
.95 24.1
.66 16.8
1.325 33.66
.437 11.10
.60 15.2
3.925 99.70
5.600 142.24
Figure B-1. GMA 347 Outline Drawing
GMA 347 Installation Manual Page B-1 (Page B-2 blank)
190-00325-01 Revision A
+.010 +0.25
6.300 160.02
-.005 -0.13
.125 3.18 OUTSIDE
+.020 +0.51 1.275 32.39

1.195 30.35 INSIDE
-.000 0.00 OUTSIDE
6.140±.005 155.96±0.13
INSIDE
NOTES:
1. DIMENSIONS: INCHES [mm]
Figure B-2. GMA 347 Rack Dimensions (115-00427-00)

190-00325-01 Revision A
211-60234-08
(2 PLACES)
1
115-00427-00
211-63234-12
(4 PLACES)
2
125-00080-00
1
330-00185-78
336-00021-00 (AS REQ'D)
(2 PLACES)
2
011-00950-04
(2 PLACES)
2
011-01169-01
NOTES: (2 PLACES)
1. PART OF 011-00812-XX GMA 1347 BACKPLATE ASSY 2
2. PART OF 011-00813-XX GMA 1347 CONNECTOR KIT
3. APPLY THREAD LOCKING COMPOUND TO ALL THREADED FASTENERS
Figure B-3. GMA 347 Connector/Rack Assembly Drawing

190-00325-01 Revision A
Figure C-1. GMA 347 Power, Antenna and Speaker Interconnect Wiring Diagram
GMA 347 Installation Manual Page C-1 (Page C-2 blank)
190-00325-01 Revision A
Figure C-2. Mic and Phone Jack Connections, Interconnect Wiring Diagram
190-00325-01 Revision A
Figure C-3. Transceiver Analog Connections, Interconnect Wiring Diagram

190-00325-01 Revision A
Figure C-4. Discrete Lines, Interconnect Wiring Diagram

190-00325-01 Revision A
Figure C-5. GMA 340 to GMA 347 Comparison

190-00325-01 Revision A

GMA 347 Audio Panel Installation Manual: Garmin Ltd. or Its Subsidiaries

Uploaded by

Copyright:

Available Formats

GMA 347 Audio Panel Installation Manual: Garmin Ltd. or Its Subsidiaries

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GMA 347 Audio Panel Installation Manual: Garmin Ltd. or Its Subsidiaries

Uploaded by

Copyright:

Available Formats

What is the purpose of this document?

What is the purpose of this document?

What are the main sections covered in the document?

What are the main sections covered in the document?

GMA 347

Garmin Ltd. or its subsidiaries

Garmin International, Inc.

Garmin (Europe) Ltd.

Revision Revision Description ECO #

Section Page Range

Page A GMA 347 Installation Manual

INFORMATION SUBJECT TO EXPORT CONTROL LAWS

GMA 347 Installation Manual Page i

Page ii GMA 347 Installation Manual

2 INSTALLATION OVERVIEW ........................................................................................................2-1

GMA 347 Installation Manual Page iii

5 POST INSTALLATION CONFIGURATION AND CHECKOUT PROCEDURE .........................5-1

APPENDIX A CERTIFICATION DOCUMENTS

APPENDIX B ASSEMBLY AND INSTALLATION DRAWINGS

APPENDIX C INTERCONNECT DRAWINGS

2-1 GMA 347 Unit Rack .........................................................................................................................2-7

3-1 Shield Block Install onto Backshell Connector Assembly ................................................................3-4

4-1 Back of Unit, Connector Location .....................................................................................................4-1

Page iv GMA 347 Installation Manual

5-1 About GMA Config Tool ..................................................................................................................5-1

A-1 GMA 347 Environmental Qualification Form ................................................................................. A-4

GMA 347 Installation Manual Page v

3-1 Pin Contact Part Numbers..................................................................................................................3-1

Page vi GMA 347 Installation Manual

MOD SERVICE SERVICE PURPOSE OF MODIFICATION

GMA 347 Installation Manual Page vii

Page viii GMA 347 Installation Manual

1.2 Equipment Description

(FCC) 47 CFR 22.925 prohibits airborne operation of cellular telephones installed in or

GMA 347 Installation Manual Page 1-1

1.2.1 Features Summary

• Logical front panel layout

Page 1-2 GMA 347 Installation Manual

• 3 Transceiver Inputs (Figure C-3)

1.3 Technical Specifications

1.3.1 Physical Characteristics

GMA 347 Installation Manual Page 1-3

Audio Panel Transceiver inputs: 3

Page 1-4 GMA 347 Installation Manual

1.4.1 TSO/ETSO Compliance

1.4.2 TSO Deviations

GMA 347 Installation Manual Page 1-5

Part Number Document

1.6 Limited Warranty

IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR

Garmin International, Inc. Garmin (Europe) Ltd.

Page 1-6 GMA 347 Installation Manual

2.3 Cooling Air

GMA 347 Installation Manual Page 2-1

Model Front Panel Unit P/N Catalog P/N Installation

2.4.2 Equipment Available

Item Garmin P/N

2.4.3 Additional Equipment Required

Page 2-2 GMA 347 Installation Manual