SOIL

CONSOLIDATION

Settlement

Submitted to
Professor Myoung Soo Won

By Sanchari Halder
 Consolidation:
 When water drains from the soil pores, the load is gradually shifted from water to soil particles. For
fully saturated soils, the load transfer is accompanied by a volume change equal to the volume of
drained water. This process is known as CONSOLIDATION.

(a) (b) (c)

W
W
W

Figure : Terzaghi Spring analogy.

Types of Consolidation:

 Immediate Consolidation: Caused by elastic Initial

deformation of dry soil or moist and saturated compression
soil without change in moisture content.
 Primary Consolidation: Caused as a result of

Deformation
Primary Consolidation
volume change in saturated cohesive soils due
to exclusion of water occupied the void space.
 Secondary Consolidation: Occurs in saturated
cohesive soils as a result of the plastic
adjustment of soil fabrics. Secondary
Consolidation

Time (log scale)

 One-dimensional Consolidation:
Z Vertical Flow of
 Since water can flow out of a saturated soil
sample in any direction, the process of water.
consolidation is essentially three-dimensional.
 However, in most field situations, water will
not be able to flow out of the soil by flowing
horizontally because of the vast expanse of
the soil in horizontal direction.
 Therefore, the direction of flow of water is X
primarily vertical or one-dimensional.
 As a result, the soil layer undergoes one
dimensional or 1-D consolidation settlement
in the vertical direction. Y
Terzaghi's theory of one-dimensional
consolidation:
All quantifiable changes in stress to a soil are a direct result of a change in effective stress

Total Stress, σ = Effective Stress,σ´ + Pore Pressure, u

Assumptions of Terzaghi's Principle σ
 The soil is homogenous & is laterally confined
 The soil is fully saturated.
 The solid particles and water are incompressible.
 Compression and flow are one-dimensional.
 Soil’s own weight is relatively small.
 Darcy's Law is valid for all hydraulic gradients. σ
 The coefficient of permeability, k and the coefficient of volume compressibility, mv remain
constant.
 The relationship between the void ratio, e and effective stress σ is linear during a stress increment.
Coefficient of Consolidation,Cv :

 The rate by which compression can occur in soil. The rate and amount of
compression in soils varies with the rate at which pore water is lost, and therefore
depends on permeability.

Coefficient of permeability, k
Cv =
Coefficient of compressibility, mv × Density of water, γw
 Determination of Consolidation Coefficient,Cv
during Primary Consolidation:

 Square-Root-Time
 Log-Time Method Method
 Nonlinear (1-D) relation between Void
Ratio (e ) & Settlement (Δh) :

 Void Ratio, e = e0 - εv (1+ e0 )

Load
𝜟𝒉
= e0 - (1+ e0)
ho
Porous Disks
Soil
Initial Δh
Height,ho

Figure: Basic Experiment setup of consolidation cell.

Void Ratio,e Vs Effective Stress, σ Curves:

 Void ratio-effective

Compression
stress and

Void Ratio
compression-time plots
for Sand

Effective Stress Time (min)

Compression
 Void ratio-effective

Void Ratio
stress and
compression-time plots
for Clay

Effective Stress Time (min)

 Normally Consolidated Soils:
It is a soil deposit that has never subjected to
a vertical effective stress greater Void Ratio
than the present vertical stress.

σpc´ σ2´ Log σv

Figure: Void ratio versus effective stress (log scale)

 Over Consolidated Soils:

It is a soil deposit that has been subjected to A B C
vertical effective stress greater than
the present vertical effective stress. Void Ratio

σ2A´ σ2B´ σpc´ Log σv

Figure: Void ratio versus effective stress (log scale)
 Over-consolidated Ratio, OCR:

 OCR is defined as the ratio of maximum

past vertical effective stress (σ’vmax) over
present vertical effective stress (σ’v).
 The maximum past vertical effective
stress is also called the preconsolidation
pressure (σ’c).

σ´v max
Over-consolidated Ratio, OCR =
σ´v
 Recompression line Normally Consolidation line
Compression Index, Cc:
 The slope of the loading curve is called Cr
1
the Compression Index, Cc and it’s Cr~ Recompression index Loading
dimensionless.
e Cc
e1−e0 Unloading
Cc = -
log(σ´v1−σ´v0) 1
Cc~ Compression index
 The negative sign is used because the
void ratio decreases when the effective Cs
1
Or swelling index
stress is increased. Swelling or Reloading line

Log σ´
Recompression
Swelling Index, Cs:
It is the average slope of the
unloading/reloading curves in e – log´ plot Virgin Compression
given by
Average line of Swelling
e e1
/ Reloading
Cs = e1−e2 e2
log 10σ´2 Expansion
σ´1
Normally Consolidated

σ´2 σ´1 Log σ´

 Coefficient of compressibility, mv:

 The coefficient of volume compressibility mv

is defined as the ratio of volumetric strain
over change in effective stress.

 The units for mv are the inverse of pressure,

i.e. m²/kN and its value depends on the
stress range over which it is calculated.
Consolidation Test(1-D Oedometer Test):

 This test is performed to determine the magnitude and rate of volume decrease that a laterally confined
soil specimen undergoes when subjected to different vertical pressures.
 From the measured data, the consolidation curve (pressure-void ratio relationship) can be plotted.
 This data is useful in determining the compression index Cc, the recompression index Cr and the
preconsolidation pressure (or maximum past pressure) of the soil.
 In addition, the data obtained can also be used to determine the coefficient of consolidation Cv and the
coefficient of secondary compression mv of the soil.

Equipment:
 Consolidation device (including ring, porous stones, water reservoir, and load
 plate),
 Dial gauge (0.0001 inch = 1.0 on dial),
 Sample trimming device, glass
 plate, Metal straight edge, Clock, Moisture can, Filter paper.
 Test Procedure:

 Weighing the empty consolidation ring together with

glass plate.

 Measuring the height (h) of the ring and its inside

diameter (d).

 Extruding the soil sample from the sampler, generally

thin-walled Shelby tube.
 Cutting approximately a three-inch long sample.
 Being careful throughout the trimming process to insure
that there is no void space between the sample and the
ring.
 Turning the ring over carefully and removing the portion
of the soil protruding above the ring. Using the metal
straight edge, cutting the soil surface flush with the
surface of the ring.

 Place the previously weighed Saran-covered glass plate

on the freshly cut surface, turn the ring over again, and
carefully cut the other end in a similar manner.
 Weigh the specimen plus ring plus glass plate.

 Carefully remove the ring with specimen from

the Saran-covered glass plate and peel the
Saran from the specimen surface.

 Adjust the dial gauge to a zero reading. set the

pressure gauge dial (based on calibration curve)
to result in an applied pressure of 0.5 tsf (tons
per square foot).

 Record the consolidation dial readings at the

elapsed times given on the data sheet. & Etc.
 Calculation:

 Determine the height of solids (Hs ) of the  Calculate the coefficient of consolidation (Cv )
specimen in the mold from t90

Hs = Ws Cvt90
(𝜋4 D²) Gs ρw Tv = H²
 Determine the change in height (ΔH)
 Calculate the coefficient of consolidation (Cv )
from t50
 Determine the final specimen height, (Ht(f))
𝐂𝐯t50
Tv = 𝐻²

 Determine the height of voids (Hv )  Plot e-log p curve and find: σc, Cc, Cr
Hv = Ht(f) - Hs
 Plot σc – log p curves
 Determine the final void ratio
Hv
e=
Hs
Example:
Thank you all……….