Effective Stress in Soil Seeee

EFFECTIVE STRESS IN SOIL, DEVELOPMENT, IMPORTANCE AND PRINCIPLES
DECEMBER 11, 2016 SHANMUKHA LEAVE A COMMENT

When a building is constructed, its weight is transmitted to the ground through its foundation, thus inducing
stresses in the underlying strata. These induced stresses might cause problems such as excessive
settlement or shear failure and thus are important to geotechnical engineers.
Stresses in Sub-Soil:
Stresses in sub-soil are caused by:
(i) Self weight of soil
(ii) Structural load on the soil
Stresses developed in saturated soil are:

(i) Effective stresses
(ii) Neutral stresses
(iii) Total stresses.
Effective Stress:
Karl Terzaghi was the first to recognize the importance of effective stress. It is the stress transmitted
through grain to grain at the point of contact through soil mass. It is also known as inter-granular stress. It is
denoted by σ’. When soil mass is loaded. The load is transferred to the soil gains through their point of
contact. If at the point of contact, the applied load is greater than the resistance of the grains, then there will
be compression in the soil mass.
This compression is partly due to the elastic compression of the grains at the points of contact and partly
due to relative sliding between particles. This load per unit area of soil mass responsible for deformation of
the soil mass is termed as effective stress.
Neutral Stress:
It is the stress or pressure transmitted through the pore fluid. It is also termed as pore pressure and is
denoted by u. In saturated soil, pores of the soil mass are filled with water. When the saturated soil mass is
loaded, the load is not transmitted through the grains. The load is transferred to the pore water. As water is
incompressible, a pressure is developed in the pore water.
This pressure is called pore pressure or pore water pressure. Pore pressure does not have any measurable
influence on the mechanical property of the soil like void ratio, shear strength etc. This pressure or stress is
called neutral stress.
Total Stress:
Total stress is equal to the sum of the effective stress and the neutral stress. It is denoted by σ.
σ=σ+u
Effective stress cannot be measured in the field by any instrument. It can only be calculated after
measuring total stress and pore pressure. Thus effective stress is not a physical parameter, but is only very
useful mathematical concept for determination of engineering behaviour of soil.
Importance of Effective Stress in Engineering Problems:

The effective stress plays an important role in:
(i) Settlement of soil
(ii) Shear strength of soil
Settlement of Soil:
The phenomenon of gradual reduction in volume of soil due to expulsion of water from soil pores is called
consolidation or compression or settlement of soil. Figure 5.3 shows a compression curve of clay. It is a
curve between effective stress σ and void ratio e. It is clear from the graph that when σ increases e
decreases i.e., due to increase in the effective stress the compression of soil will increase.
The final consolidation settlement may be calculated by using
the formula
S = mV H
where mV is the coefficient of volume compressibility
H is the thickness of compressible layer
∆σ is the average increase in effective pressure.
From the above equation it is clear that settlement of soil is directly proportional to the effective pressure.
So the settlement of soil depends upon the effective stress or effective pressure. As the effective stress
increases, the settlement of the soil also increases.
Shear Strength of Soil:

Many geotechnical engineering problems require an assessment of shear strength including:
(a) Structural foundations:
Load from a structure is transferred to ground through foundation. This produces shear stress and
compressive stress. If shear stress produced is more than the shear strength of soil, shear failure occurs
which cause the structure to collapse.
(b) Earth slopes:
On a sloping ground, gravity produces shear stresses in the soil. If these stresses exceed the shear
strength, a landside occurs.
(c) Highway pavements:
Wheel loads, from vehicles are transferred through pavement to the ground. These loads produce shear
stress which causes shear failure.
Do You Know?
The value of K in x-direction is equal to that in y-direction for a level ground surface.
Shear strength of soil is calculated by using the formula
S = σ tan ɸ
Where σ = Effective stress
ɸ= Effective friction angle
For a given soil, f is constant. Shear strength is then directly proportional to effective stress. So with
increase in effective stress the strength increases. If shear strength of soil is more, shear failure will be
less.
Principle of Effective Stress:

If the saturated soil mass is loaded, the load is transferred to the pore water. After expulsion of pore water it
is transferred to the soil grains. Let YY be the wavy plane passing through the points of contact of the soil
grains. Let A be the area of the wavy plane YY. This area A is the sum of area of grains contact (A g) and
area of the pore water (Aw) as shown in figure 5.5. It is evident from figure 5.6 that area of grains contact
(Ag) is much less than the area of pore water (Aw) i.e., Aw = A.
Let F be the total load on area A.

The principle of effective stress in its simplest from can be stated as
(i) The effective stress is equal to the total stress minus the pore pressure for a saturated soil
σ=σ–u
(ii) The effective stress controls certain aspects of soil behaviour like strength, deformation etc.

Effective Stress in Soil Seeee

Uploaded by

Copyright:

Available Formats

Effective Stress in Soil Seeee

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Effective Stress in Soil Seeee

Uploaded by

Copyright:

Available Formats

EFFECTIVE STRESS IN SOIL, DEVELOPMENT, IMPORTANCE AND PRINCIPLES

DECEMBER 11, 2016 SHANMUKHA LEAVE A COMMENT

(ii) Structural load on the soil

Stresses developed in saturated soil are:

(ii) Neutral stresses

(iii) Total stresses.

Importance of Effective Stress in Engineering Problems:

(ii) Shear strength of soil

∆σ is the average increase in effective pressure.

Shear Strength of Soil:

Shear strength of soil is calculated by using the formula

Where σ = Effective stress

ɸ= Effective friction angle

Principle of Effective Stress:

The principle of effective stress in its simplest from can be stated as

You might also like