Nxplus C

Medium-Voltage Switchgear
Type NXPLUS C Fixed-Mounted Circuit-Breaker Switchgear up to 24 kV,

Extendable
Single Busbar, Metal-Enclosed, Gas-Insulated
M edium -Voltage S witchgear
INSTALLATION AND
OPERATING
INSTRUCTIONS
Order No.: 802-9081.9

Revision: 11
Issue: 19-01-2018
About these Instructions
These instructions do not purport to cover all details or For further details, e.g. about additional equipment, please
variations in equipment, nor to provide for every possible refer to catalog HA 35.41.
contingency to be met in connection with installation or
Should further information be desired or should particular
operation.
problems arise which are not covered sufficently by these
For details about technical design and equipment like e.g. instructions, the matter should be referred to the
technical data, secondary equipment, circuit diagrams, competent Siemens department.
please refer to the order documents.
The contents of this instruction manual shall not become
The switchgear is subject to continuous technical part or modify any prior or existing agreement,
development within the scope of technical progress. If not commitment or relationship. The Sales Contract contains
stated otherwise on the individual pages of these the entire obligations of Siemens. The warranty contained
instructions, we reserve the right to modify the specified in the contract between the parties is the sole warranty of
values and drawings. All dimensions are given in mm. Siemens. Any statements contained herein do not create
new warranties or modify the existing warranty.
2/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

Contents
Safety instructions ............................................. 6 10.7 Rating plates .................................................... 72
1 Signal terms and definitions ............................... 6 10.8 Vacuum circuit-breaker..................................... 72
2 General instructions ........................................... 6 10.9 Three-position disconnector for
circuit-breaker, disconnector and bus sectionalizer
3 IT security .......................................................... 8
panels ≥ 1000 A.............................................. 76
4 Due application .................................................. 9
10.10 Three-position switch-disconnector for
5 Qualified personnel ............................................ 9 switch-disconnector panels, ring-main panels
Description ....................................................... 10 and circuit-breaker panels up to 630 A, vacuum
contactor panel and metering panel ................. 76
6 Features........................................................... 10
10.11 Endurance classes ............................................ 77
7 Panel types....................................................... 12
10.12 Vacuum contactor ............................................ 78
8 Examples for panel versions ............................. 13
10.13 Insulating gas................................................... 79
8.1 Circuit-breaker panels....................................... 13
11 End of life ........................................................ 80
8.2 Disconnector panels ......................................... 17
Installation........................................................ 81
8.3 Bus sectionalizer............................................... 19
12 Constructional stipulations ............................... 81
8.4 Switch-disconnector panel................................ 21
12.1 Switchgear room.............................................. 81
8.5 Vacuum contactor panel................................... 22
12.2 Constructional data of the foundation .............. 84
8.6 Ring-main panel ............................................... 23
12.3 Transport units................................................. 94
8.7 Metering panel................................................. 23
13 Before installation ............................................ 96
9 Components .................................................... 24
13.1 Preliminary clarifications................................... 96
9.1 Circuit-breaker ................................................. 24
13.2 Intermediate storage ........................................ 96
9.2 Vacuum contactor ............................................ 25
13.3 Tools/auxiliary means ....................................... 97
9.3 Three-position disconnector ............................. 26
13.4 Comments on electromagnetic compatibility .... 98
9.4 Three-position switch-disconnector .................. 26
14 Unloading and erecting the switchgear........... 100
9.5 Operating mechanisms for three-position
switch .............................................................. 27 14.1 Packing and transport unit.............................. 100
9.6 Voltage transformers 4MT ................................ 28 14.2 Completeness and transport damages ............ 100
9.7 Current transformers 4MC ................................ 31 14.3 Unloading and transporting to place of
installation ..................................................... 101
9.8 HV HRC fuse assembly ...................................... 32
14.4 Checking the ready-for-service indicator ......... 105
9.9 Busbar system .................................................. 33
15 Assembling the switchgear............................. 107
9.10 Cable connection ............................................. 34
15.1 Aligning and joining the panels ...................... 108
9.11 Ready-for-service indicator ............................... 52
15.2 Fastening the panel to the foundation ............ 110
9.12 Interlocks ......................................................... 53
15.3 Removing transport braces ............................. 110
9.13 Voltage detecting systems ................................ 54
15.4 Assembling the busbars.................................. 111
9.14 Accessories ...................................................... 54
15.5 Mounting the busbar support ......................... 122
10 Technical data .................................................. 58
15.6 Installi ng current transformers on the
10.1 Complete switchgear........................................ 58 busbar ........................................................... 124
10.2 Classification of NXPLUS C according to 15.7 Installing busbar voltage transformers ............ 127
IEC 62271-200 ................................................. 59
15.8 Interconnecting the earthing busbars ............. 132
10.3 Standards, specifications, guidelines................. 60
15.9 Switchgear earthing ....................................... 132
10.4 Selection of HV HRC fuse-links .......................... 61
15.10 Installing the low-voltage compartment ......... 133
10.5 Motor protection table (with HV HRC fuses
make SIBA)....................................................... 70 15.11 Installing the horizontal pressure relief duct.... 134
10.6 Fuse protection table for metering panel 15.12 Installing the switchgear termination.............. 143
(with HV HRC fuse-links make SIBA) .................. 71 15.13 Mounting the busbar covers ........................... 144
802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 3/293

15.14 Mounting the air guides ................................. 151 21.4 De-earthing with the three-position switch..... 194
15.15 Extension with individual panels .................... 154 21.5 Operating the three-position switch with
motor-operating mechanism.......................... 195
16 Electrical connections .................................... 154
21.6 Protection tripping of the
16.1 Installation work at the floor cover ................. 155
switch-fuse combination ................................ 195
16.2 Connecting cable T-plugs ............................... 158
21.7 Emergency operation of the three-position
16.3 Panels 2000 A, 2500 A with double switch with slow motion mechanism
connections ................................................... 163 (900 mm panel width) ................................... 196
16.4 Connecting surge arresters............................. 164 22 Work-in-progress earthing.............................. 201
16.5 Connecting surge limiters .............................. 165 23 Verification of safe isolation from supply ........ 203
16.6 Connecting auxiliary circuits........................... 166 23.1 LRM plug-in sockets ....................................... 203
17 Installation of degree of protection 23.2 VOIS and CAPDIS indications .......................... 205
versions IP31D, IP32D and IP34D .................... 171
23.3 WEGA indications........................................... 207
17.1 IP31D - protection against vertically
24 Replacing HV HRC fuse-links ........................... 208
falling water drops......................................... 171
17.2 IP32D - protection against vertically falling water 25 Operating the feeder voltage transformer ...... 212
drops for switchgear inclined up to 15° .......... 175 25.1 Disconnecting the feeder voltage
transformer ................................................... 212
17.3 IP34D - protection against splashing water from
any direction.................................................. 176 25.2 Connecting the feeder voltage transformer .... 213
18 Commissioning .............................................. 177 26 Short instructions .......................................... 214
18.1 Final work...................................................... 177 26.1 Operating circuit-breaker panels (600 mm panel
width) ........................................................... 214
18.2 Checking the accessories................................ 179
18.3 Instructing operating personnel ..................... 179 26.2 Operating circuit breaker panels (900 mm panel
width) ........................................................... 220
18.4 Function test / Test operation ......................... 179
26.3 Operating vacuum contactor panels ............... 226
18.5 Performing the power- frequency
26.4 Operating switch-disconnector, disconnector,
voltage test.................................................... 183
ring-main and metering panels with 600 mm
18.6 Primary injection test ..................................... 184 panel width ................................................... 230
18.7 Correcting circuit diagrams ............................ 184 26.5 Operating disconnector panels as of 2000 A
18.8 Applying operating voltage ............................ 184 (900 mm panel width) ................................... 234
Operation........................................................ 186 26.6 Operating bus sectionalizer panels with 600 mm

panel width ................................................... 238
19 Control elements and indicators..................... 187
26.7 Operating bus sectionalizer panels with 900 mm
19.1 Position indicators.......................................... 188 panel width ................................................... 242
19.2 "Spring charged" indicator.............................. 188 26.8 Operating bus sectionalizer panels with two three-
19.3 Operations counter ........................................ 188 position disconnectors and with 600 mm panel
width............................................................. 246
19.4 Ready-for-service indicator ............................. 189
26.9 Operating bus sectionalizer panels with two three-
19.5 Circuit-breaker locking device for
position disconnectors and with 900 mm panel
"feeder earthed"............................................. 189
width............................................................. 253
20 Operating the circuit-breaker ......................... 190
26.10 Operating the circuit-breaker panel with busbar
20.1 Closing the circuit-breaker.............................. 190 earthing switch.............................................. 261
20.2 Opening the circuit-breaker............................ 190 27 Cable testing.................................................. 266
20.3 Charging the closing spring............................ 190 Service information ........................................268
20.4 Circuit-breaker test operation ......................... 191 28 Maintenance.................................................. 268
21 Operating the three-position switch ............... 192 28.1 Maintenance of circuit-breaker 3AH25 with
21.1 Closing the three-position switch ................... 193 30000 operating cycles .................................. 268
21.2 Opening the three-position switch ................. 193 29 Checks and maintenance work in case of special
operating conditions ...................................... 275
21.3 Earthing/ready-to-earth with the three-position
switch............................................................ 194

29.1 Visual check at the operating mechanisms and the 31 Extending the switchgear or replacing panels and
three-position switches .................................. 276 components................................................... 284
29.2 Visual check of spring-operated mechanism.... 276 Annex ............................................................. 285
29.3 Visual check of slow motion mechanism ......... 278 32 MCU-MH
29.4 Visual check of spring-operated/stored-energy (Motor Control Unit - Module Housing) ........... 285
mechanism .................................................... 279 32.1 Extract from the Technical Description ............ 285
29.5 Visual check of circuit-breaker operating 32.2 Application..................................................... 285
mechanism .................................................... 281
32.3 Design, function............................................. 285
29.6 Visual check of vacuum contactor operating
32.4 Technical data ................................................ 286
mechanism .................................................... 282
32.5 Fault signals ................................................... 286
29.7 Cleaning, greasing and lubricating the operating
mechanisms................................................... 283 32.6 Terminal assignment of motor control unit ..... 287
29.8 Test operation of the operating mechanisms .. 283 Siemens Service Hotline ................................. 288
30 Permissible lubricants..................................... 284 Index............................................................... 289

Safety instructions
Safety instructions
1 Signal terms and definitions
The signal words "danger," "warning" and "caution" used in this instruction manual indicate
the degree of hazard that may be encountered by the user.
DANGER
Danger - Indicates an imminently hazardous situation.
If this hazardous situation is not avoided, death or serious injury will be the consequence.
➭ Observe the safety instructions.
WARNING
Warning - Indicates a potentially hazardous situation.
If this hazardous situation is not avoided, death or serious injury can be the consequence.
CAUTION
Caution - Indicates a potentially hazardous situation.
If this hazardous situation is not avoided, minor or moderate injury can be the
consequence.
NOTICE
Note - Indicates a potentially hazardous situation.
If this hazardous situation is not avoided, damage to property or environment can be the
consequence.
➭ Observe the notes.
INFORMATION
Information - Indicates an important information or facilitation of work.
➭ Observe the information.
Symbols used ➭ Operation symbol: Identifies an operation. Asks the operator to perform an operation.
✔ Result symbol: Identifies the result of an operation.
2 General instructions
Important • The personnel must read and understand this manual before starting to work.
• Observe all safety instructions and warnings in this manual, and follow the instructions.
• Store this manual carefully, and so that it is accessible to the personnel at any time.
• This manual is a part of the product. When the switchgear is transferred, supply this manual
as well.
INFORMATION
The illustrations included in this manual are simplified and serve to create a general
understanding. The illustrations may therefore deviate from the actual product.

Safety instructions
INFORMATION
Preconditions for perfect and safe operation of the switchgear:
➭ Observance of operating and installation instructions.
➭ Qualified personnel.
➭ Proper transportation and correct storage of the switchgear.
➭ Correct installation and commissioning.
➭ Diligent operation and maintenance.
➭ Observance of the installation, operation and safety regulations applicable at the place of
installation.
WARNING
Any kind of modification on the product or alteration of the product must be coordinated
with the manufacturer in advance.
Uncoordinated modifications or alterations can cause the expiration of warranty claims,
cause danger to life, limb and other legally protected interests.
The fulfillment of the type tests (according to IEC 62271-200) may not be guaranteed
anymore. This applies especially though not exclusively to the following actions, e.g. in the
course of maintenance or repairs.
➭ Use Siemens original parts only.
➭ Service technicians performing replacement are trained and certified by Siemens.
➭ Install or adjust parts properly.
➭ Perform settings in accordance with Siemens specifications.
➭ After installation and setting, have a final check performed by a service engineer approved
by Siemens, including documentation of the test results.
➭ Perform maintenance according to the operating instructions of the Siemens products.
The switchgear corresponds to the relevant laws, prescriptions and standards applicable at the
time of delivery. If correctly used, it provides a high degree of safety by means of logical
mechanical interlocks and shockproof metal enclosure of live parts.
Independently of the safety instructions given in these operating instructions, the local laws,
ordinances, guidelines and standards for operation of electrical equipment as well as for labor,
health and environmental protection apply.
The switchgear operator or owner must keep the technical documents supplied with the
switchgear throughout the entire service life, and keep them up-to-date in case of
modifications of the switchgear.
Five Safety Rules of The Five Safety Rules of Electrical Engineering must be complied with during operation of the
Electrical Engineering products and components described in these operating instructions:
• Isolate.
• Secure against reclosing.
• Verify safe isolation from supply.
• Earth and short-circuit.
• Cover or barrier adjacent live parts.
Hazardous substances If hazardous substances are required to perform the work, the relevant safety data sheets and
operating instructions must be observed.
Personal protective For switchgear with proof of internal arc classification according to IEC 62271 Part 200, no
equipment (PPE) personal protective equipment must be worn for operating the switchgear.
For switchgear without proof of internal arc classification according to IEC 62271 Part 200,
personal protective equipment must be worn for operating the switchgear.
If covers have to be removed to work on switchgear, personal protective equipment must be
worn for protection against hot gases exhausting in case of internal arc. In case of internal arc,
full personal protection is not provided, even if the personal protective equipment is worn.

Safety instructions
To select the protective equipment, the local laws and regulations must be observed and
accomplished.
The personal protective equipment consists of:
• Protective clothing
• Safety shoes
• Gloves
• Helmet and face protection
• Ear protection
Removing the front cover from the operating mechanism compartment
WARNING
High speed moving parts
Can cause serious injury.
Do not remove the front cover of the operating mechanism until the following actions have
been performed:
➭ To avoid impermissible switching operations, switch off auxiliary voltage, e.g.:
- Switch the auxiliary voltage supply of the motor.
- Trip the MCB.
- Disconnect the control cables from the low-voltage compartment.
➭ To discharge the spring energy store in the operating mechanism, execute the following
instructions:
- Actuate the manual OFF pushbutton.
- Actuate the manual ON pushbutton.
- Actuate the manual OFF pushbutton again.
➭ Check if the "spring charged" indicator shows "spring charged".
Fig. 1: "Spring not charged" indication Fig. 2: "Spring charged" indication
3 IT security
The Siemens software is regularly checked for safety. If weak points are identified in the
process, which may allow third parties to access protection devices, information thereto is
distributed through the SIPROTEC and SICAM Security Update Report Newsletter.
The Newsletter can be subscribed to at the following website:
www.siemens.com/gridsecurity
Before commissioning the switchgear, it must be verified that the current firmware version is
installed on the protection devices. The latest version of firmware can be obtained from the
following website:
http://w3.siemens.com/smartgrid/global/en/products-systems-solutions/downloads/
Pages/Overview.aspx
For information to updates for other makes of protection devices, please contact the
respective manufacturer.

Safety instructions
4 Due application
Extendable fixed-mounted circuit-breaker switchgear NXPLUS C, single busbar, is used in
transformer and distribution substations as well as for switching duties in industrial plants.
The panels are designed for rated voltages up to 24 kV and rated currents up to 2500 A. In
distribution systems up to 24 kV (15 kV), a maximum short-circuit current of 25 kA (31.5 kA) is
permissible.
5 Qualified personnel
Qualified personnel in accordance with these instructions are persons who have been instructed
by the Switchgear Factory Frankfurt (participation in an assembly and installation training with
certificate), who are familiar with transport, installation, commissioning, maintenance and
operation of the product, and who have appropriate qualifications for their work.
• Training and instruction or authorization to switch on, switch off, earth and identify power
circuits and equipment / systems as per the relevant safety standards.
• Training regarding the applicable specifications for the prevention of accidents and the use
of appropriate safety equipment.
• Training in first aid and behavior in the event of possible accidents.

Description
Description
6 Features
Technology • Factory-assembled, type-tested and metal-enclosed switchgear for indoor installation
• Stainless-steel vessel welded gas-tight
• Gas-insulated switching-device compartment
• Cable connection and busbar, single-pole insulated
• Installation and extension of the switchgear possible without SF 6 gas work
• Screened busbar, silicone-rubber insulated
• Cable connection from front with cable plugs
• Maintenance-free under normal operating conditions
Insulating gas SF6 Sulfur hexafluoride SF6 is used as insulating gas. SF6 insulates live parts between each other
and against the vessel wall. For panels with switch disconnector, SF 6 serves also for
extinguishing the internal arc.
The switchgear is delivered ex works with SF6 filling, ready for service. The SF 6 filling is
provided to last the total service life of the switchgear.
No gas work is required for installation on site and later extensions.
Filling quantity as per rating plate.
Personal safety • Safe-to-touch due to metal enclosure of live parts

• Clear mimic diagram with mechanical position indicators
• HV HRC fuses are only accessible when outgoing feeders are earthed
• Logical mechanical interlocking
• Capacitive voltage detecting system to verify safe isolation from supply
• Earthing of outgoing feeders by means of make-proof earthing switch (this does not apply
to disconnector panels)
• Resistance to internal arcing
- Pressure-resistant design of connection compartments
- Rear pressure relief duct (optional for wall-standing arrangement)
Security of operation and • Hermetically sealed primary enclosure independent of environmental effects, such as
availability pollution, humidity and small animals
• Welded switchgear vessel, sealed for life
• Operating mechanisms of switching devices accessible outside the switchgear vessel
• Maloperation is practically excluded due to interlocks and logical arrangement of operating
elements
• Self-monitoring ready-for-service indicator, easy to read, independent of temperature and
environmental pressure variations, with contactless measured-value acquisition and with
signaling switch (option) 1 changeover contact for telecommunication
• Minimum fire load
• Switchgear vessel designed as "sealed pressure system" according to IEC 62271-200, i.e. the
insulating gas filling requires no maintenance
Cost-efficiency Extremely low "lifecycle costs" and maximum availability thanks to:
• Maintenance-free design under normal operating conditions (for the service life)
• Minimum space requirement
• Long service life

Description
National approvals NXPLUS C switchgear has obtained the following national approval:
• GOST R certificate
Type approval NXPLUS C switchgear has been type-approved by the following classification societies:
• Lloyds Register (LR)
• Det Norske Veritas (DNV)
• Germanischer Lloyd (GL)
• Russian Maritime Register of Shipping (RMRS)
• American Bureau of Shipping (ABS)
The switchgear is therefore also approved for application on ships and platforms.
Seismic withstand NXPLUS C switchgear can be upgraded for regions at risk from earthquakes. For upgrading,
capability (option) earthquake qualification testing has been carried out in accordance with the following
standards:
• IEC 60068-3-3 “Guidance – seismic test methods for equipment”
• IEC 60068-2-57 “Test Ff: Vibration – Time-history method”
• IEC 60068-2-59 “Test Fe: Vibration – Sine-beat method”
• IEEE 693-2005 “Recommended Practice for Seismic Design of Substations”.
For installation on even and rigid concrete or steel structure (without considering building
influences), the tested ground accelerations meet the following requirements:
• Uniform Building Code 1997 (UBC) – Zone 4
• California Building Code 1998 (CBC) – Zone 4
• IEEE 693-2005 – High required response spectrum.

Description
7 Panel types
Circuit-breaker panel Disconnector panel Switch-disconnector panel Bus sectionalizer
Metering panel Vacuum contactor panel Ring-main panel
Vacuum circuit- Three-position switch- Capacitive voltage

Three-position disconnector
breaker disconnector detecting system
These components can be

Cable (not included in the
Current transformer Voltage transformer -------------- connected partially or
scope of supply)
optionally
HV HRC fuse Vacuum contactor

Description
8 Examples for panel versions
8.1 Circuit-breaker panels
① Rear pressure relief duct

② Busbar voltage transformer (option)
③ Busbar system
④ Three-position disconnector
⑤ Switchgear vessel, hermetically welded, filled with SF 6
gas, with bursting disc
⑥ Circuit-breaker with vacuum interrupters
⑦ Ring-core current transformer (option)
⑧ Cable with cable plug for outside-cone plug-in system
⑨ Voltage transformer (option)
⑩ Voltage transformer disconnector (option)
⑪ Cover to cable compartment
⑫ Capacitive voltage detecting system (busbar: left side,
cable feeder: right side)
⑬ Control board
⑭ SIPROTEC bay controller (option)
⑮ Low-voltage compartment
Fig. 3: Circuit-breaker panel (630 A)

③ Busbar system
⑬ Control board

Description

③ Busbar system
⑤ Switchgear vessel, hermetically welded, filled with SF6
⑬ Control board
* 752 mm for deep cable compartment cover

** 1120 mm for deep cable compartment cover
① Air guide
② Busbar system
③ Three-position disconnector
④ Switchgear vessel, hermetically welded, filled with SF 6
⑤ Circuit-breaker with vacuum interrupters
⑥ Ring-core current transformer (option)
⑦ Cable with cable plug for outside-cone plug-in system
⑧ Voltage transformer (option)
⑨ Voltage transformer disconnector (option)
⑩ Cover to cable compartment
⑪ Capacitive voltage detecting system (busbar: left side,
⑫ Control board
⑬ Low-voltage compartment
* 2650 mm for high low-voltage compartment

** 752 mm for deeper cable compartment cover
*** 1245 mm for deeper cable compartment cover
Fig. 6: Circuit-breaker panel (2000 A and 2500 A)

Description

③ Busbar system
⑬ Control board

** 752 mm for deep cable compartment cover
*** 1120 mm for deep cable compartment cover
Fig. 7: Circuit-breaker panel (1000 A and 1250 A with
30000 operating cycles)

Description
① Rear pressure relief duct / cable

compartment
③ Busbar system
⑤ Switchgear vessel, hermetically welded,
filled with SF6 gas, with bursting disc
⑧ Cable with cable plug for outside-cone
plug-in system
⑨ Cover to cable compartment
⑩ Capacitive voltage detecting system
(busbar: left side, cable feeder: right side)
⑪ Control board
⑫ SIPROTEC bay controller (option)
* 2650 mm for high low-voltage

compartment
** When only one cable is connected, the
dimension is reduced by 275 mm
Fig. 8: Circuit-breaker panel with top-rear cable connection (1250 A)
Fig. 9: Circuit-breaker panel with bottom-rear cable connection (1250 A)

Description
8.2 Disconnector panels

③ Busbar system
⑤ Switchgear vessel, hermetically welded, filled with
SF6 gas, with bursting disc
⑦ Cable with cable plug for outside-cone plug-in
system
⑪ Capacitive voltage detecting system (busbar: left
side, cable feeder: right side)
⑫ Control board
⑬ SIPROTEC bay controller (option)
⑭ Low-voltage compartment
Fig. 10: Disconnector panel (1000 A)

③ Busbar system
⑫ Control board
⑬ SIPROTEC bay controller (option)
⑭ Low-voltage compartment
Fig. 11: Disconnector panel (1250 A)

Description
① Air guide
② Busbar system
⑤ Cable with cable plug for outside-cone plug-in system
⑦ Voltage transformer (option)
⑧ Voltage transformer disconnector (option)
⑨ Cover to cable compartment
⑩ Capacitive voltage detecting system (busbar: left side,
⑪ Control board
Fig. 12: Disconnector panel (2000 A and 2500 A)

Description
8.3 Bus sectionalizer
① Rear pressure relief duct (option)

② Busbar system
④ Switching-device vessel, hermetically
welded, filled with SF6 gas, with bursting
disc
⑥ Cable compartment cover
⑦ Socket for capacitive voltage detecting
system (busbar: left side, cable feeder: right
side)
⑧ Control board
⑨ SIPROTEC bay controller (option)
⑩ Low-voltage compartment
* 2650 mm for high low-voltage

compartment
Fig. 13: Bus sectionalizer panel with one or two disconnectors (1 panel spacing)
(1000 A)
Fig. 14: Bus sectionalizer panel with one or two disconnectors (1 panel spacing)
(1250 A)

Description
① Air guide
② Twin busbar system
④ Switching-device vessel,
hermetically welded, filled
with SF6 gas, with bursting
disc
⑤ Circuit-breaker with
vacuum interrupters
(only for 2500 A with
ventilation)
⑦ Socket for capacitive
voltage detecting system
(busbar: left side, cable
feeder: right side)
⑧ Control board
⑨ SIPROTEC bay controller
(option)
* 2650 mm for high low-

Fig. 15: Bus sectionalizer panel with one or two disconnectors (1 panel spacing) (2000 A and voltage compartment
2500 A)
① Rear pressure relief duct (option)

② Busbar system
④ Switching-device vessel, hermetically
welded, filled with SF6 gas, with
bursting disc
⑦ Socket for capacitive voltage detecting
system (busbar: left side, cable feeder:
right side)
⑧ Control board
⑨ SIPROTEC bay controller (option)
1) 2650 mm for high low-voltage

compartment
Fig. 16: Bus sectionalizer panel with disconnector (2 panel spacings) (1250 A)

Description
8.4 Switch-disconnector panel

③ Busbar system
④ Three-position switch-disconnector
⑥ Fuse assembly with HV HRC fuses
⑨ Cover of cable compartment
⑩ Capacitive voltage detecting system (busbar: left side,
⑪ Control board
Fig. 17: Switch-disconnector panel with HV HRC fuses

Description
8.5 Vacuum contactor panel

③ Busbar system
⑤ Switching-device vessel, hermetically welded, filled with SF 6
⑥ Contactor with vacuum interrupters
⑦ HV HRC fuse assembly with HV HRC fuses
⑨ Ring-core current transformer (option)
⑪ Cover of cable compartment
⑫ Socket for capacitive voltage detecting system (busbar: left
side, cable feeder: right side)
⑬ Control board
Fig. 18: Vacuum contactor panel with HV HRC fuses
Fig. 19: Vacuum contactor panel without HV HRC fuses

Description
8.6 Ring-main panel

③ Busbar system
⑫ Control board
Fig. 20: Ring-main panel (switch-disconnector panel without HV HRC

fuses)
8.7 Metering panel

② Busbar system
③ Three-position switch-disconnector
⑤ HV HRC fuses in the fuse assembly
⑥ Voltage transformer (option)
⑦ Cover to cable compartment
⑧ Control board
⑨ Low-voltage compartment
Fig. 21: Metering panel with HV HRC fuses

Description
9 Components
9.1 Circuit-breaker
Design The Siemens vacuum circuit-breaker (VCB) 3AH55/3AH25 is a three-pole indoor circuit-breaker
for rated voltages from 7.2 kV to 24 kV.
The circuit-breaker consists of the following components:
• Operating mechanism with stored-energy spring mechanism and control elements
• Three circuit-breaker poles with vacuum interrupters
• Partition plate
• Operating rods for contact operation, mounted in the vessel front (partition plate) in a
movable way and without seals by means of welded-in metal bellows.
The operating mechanism accommodates all electrical and mechanical components required
for closing and opening the circuit-breaker. The removable cover of the operating mechanism
contains the openings for the control elements and indicators.
The circuit-breaker is closed by pressing the ON pushbutton. After closing, the motor
recharges the closing spring. If the motor supply voltage fails, the closing spring can be
charged manually.
Vacuum interrupters The vacuum interrupter is fixed at the interrupter support. The fixed contact is directly
connected to the housing. The moving contact is firmly connected to the connection bolt and
is centrally aligned in the guide. A metal bellows forms the vacuum-tight connection to the
interrupter housing.
Fig. 22: Vacuum interrupter
Equipment The basic version of the circuit-breaker is equipped as follows:

• Electrical operating mechanism (charging motor) with mechanical and electrical anti-
pumping device (-M1)
• Closing solenoid (-Y9)
• Shunt release (-Y1)
• Low-voltage plug connector with 10-pole wiring (-Q0)
• Auxiliary switch 4NO + 4NC or 3NO + 4NC freely available (-S1)
• Position switch for "closing spring charged" indication (-S41, -S42)
• Circuit-breaker tripping signal, cutout switches (-S6, -S7)
• Operations counter
• Feeder locking device
Option • Extended auxiliary switch with 10NO + 6NC or 9NO + 6NC freely available (-S1)
• Shunt release (-Y2)
• Undervoltage release (-Y7)
• C.t.-operated release (-Y4)
• Low-energy c.t.-operated release (-Y6)
• Interlocking of feeder locking device against three-position disconnector
- Circuit-breaker only lockable in earthed position

Description
• Interlocking of feeder locking device against three-position disconnector and cable

compartment cover
- Circuit-breaker only lockable in earthed position
- Cable compartment cover only removable in earthed position
Possible release combinations
Release Release combination
1 2 3 4 5
1st shunt release Type 3AY1510 X X X X X
2st shunt release Type 3AX1101 – X – – X
C.t.-operated release Type 3AX1102; 0.5 A or – – X – X
Type 3AX1104, 0.1 Ws
Undervoltage release Type 3AX1103 – – – X –
X: 1 unit of each release, a maximum of 3 releases can be combined
9.2 Vacuum contactor
Design The Siemens high-voltage vacuum contactor 3TL72, 3TL73 and 3TL74 is a three-pole indoor
contactor for rated voltages from 7.2 kV to 24 kV. The vacuum contactor can be controlled
from remote and has an electromagnetic operating mechanism suitable for high switching
rates and unlimited operating time. The electromagnetic operating mechanism is suitable for
AC operation or DC operation.
The vacuum contactor consists of the following components:
• Operating mechanism with magnetic actuator and control elements
• Three contactor poles with vacuum interrupters
• Partition plate
• Operating rods for contact operation, mounted in the vessel front (mounting plate) in a
movable way and without seals by means of welded-in metal bellows.
• Mechanical closing latch
The vacuum contactor is latched mechanically in CLOSED position. A latch then holds the
vacuum contactor in closed position even without auxiliary voltage.
The vacuum contactor is released electrically either mechanically by means of a pushbutton
in the switchgear front, or electrically (option) by a shunt release or undervoltage release.
① Pole support
② Vacuum interrupter
③ Switchgear vessel
④ Metal bellows
⑤ Operating mechanism box
⑥ Auxiliary contactors and
rectifiers
⑦ Operating kinematics
⑧ Mechanical lockout
⑨ Magnet coil
⑩ Mechanical closing latch
⑪ Electrical latch release
The operating mechanism box accommodates all electrical and mechanical components
required for closing and opening the contactor.
The vacuum contactor has opening springs to ensure that the contactor switches off if the
supply voltage fails.
Equipment The basic version of the vacuum contactor is equipped as follows:

• Electromagnetic operating mechanism for unlimited operating time
• Auxiliary switch with 3NO + 4NC freely available
Optional • Extended auxiliary switch with 5NO + 6NC freely available

Description
9.3 Three-position disconnector

The three-position disconnector combines the DISCONNECTING and READY-TO-EARTH
functions.
Application:
• Circuit-breaker panel 1000 A to 2500 A
• Disconnector panel 1000 A to 2500 A
• Bus sectionalizer 1000 A to 2500 A
In circuit-breaker panels, earthing and short-circuiting the cable connection is completed by
closing the vacuum circuit-breaker.
Features • Operation via metal bellows or rotary bushings welded without seals into the front of the
switchgear vessel.
Basic equipment Basic version of the three-position disconnector:

• Auxiliary switch, freely available
- In READY-TO-EARTH function with 6NO + 6NC
- in DISCONNECTING function with 6NO + 6NC
• Manual operating mechanism
• Mechanical interlocking to the circuit-breaker
Additional equipment • Motor operating mechanism

• Electromechanical interlock
9.4 Three-position switch-disconnector

Designed as a multi-chamber switch with the functions DISCONNECTING and EARTHING, with
the switch positions: CLOSED – OPEN – EARTHED.
Application:
• Circuit-breaker panel 630 A
• Switch-disconnector panel
• Ring-main panel
• Vacuum contactor panel
• Metering panel
In the following panel types, earthing and short-circuiting the cable connection is performed
by switching the three-position switch-disconnector to EARTHED position.
• Ring-main panels
• Vacuum contactor panels
• Switch-disconnector panels
• Metering panels
Features • Operation via metal bellows welded without seals into the front of the switching-device
vessel.
Basic equipment Basic version of the three-position switch-disconnector:

• Auxiliary switch, freely available
- in EARTHING function with 6NO + 6NC
- in DISCONNECTING function with 6NO + 6NC
• Manual operating mechanism
Additional equipment • Motor operating mechanism

• Electromechanical interlock
• Mechanical interlocking (fuse compartment cover can only be removed in earthed position)

Description
9.5 Operating mechanisms for three-position switch

In NXPLUS C switchgear, the three-position switch-disconnector is used both as a simple
three-position disconnector in combination with the circuit-breaker and as a three-position
switch-disconnector.
The three-position disconnector and the three-position switch-disconnector are operated from
the switchgear front.
Spring-operated mechanism (rotary lever mechanism 90°, panel width 600 mm)
• Application in the following panel types:
- Circuit-breaker panel 630 A, 1000 A, 1250 A
- Disconnector panel 1000 A, 1250 A
- Bus sectionalizer panel 1000 A, 1250 A
- Vacuum contactor panel
- Metering panel
- Ring-main panel
① Position indicator for three-position switch

(DISCONNECTING function)
② Position indicator for three-position switch
(EARTHING/READY-TO-EARTH function)
③ Interrogation lever
④ Actuating opening for earthing switch
⑤ Actuating opening for disconnector
⑥ Control gate
⑦ Ready-for-service indicator
Slow motion mechanism (rotary lever mechanism 180°, panel width 600 mm)
• Application in circuit-breaker panel 1000 A, 1250 A with increased number of operating
cycles 5000 / 5000, 30000 operating cycles (option: 10000 / 10000, 30000 operating
cycles)

② Interrogation lever
③ Position indicator for three-position switch (EARTHING/
READY-TO-EARTH function)
④ Ready-for-service indicator
⑤ Actuating opening for earthing switch (EARTHING/
⑥ Actuating opening for disconnector (DISCONNECTING
function)
⑦ Control gate
Slow motion mechanism (rotary lever mechanism 180°, panel width 900 mm)
• Application in the following panel types:
- Circuit-breaker panel 2000 A, 2500 A
- Disconnector panel 2000 A, 2500 A
- Bus sectionalizer panel 2000 A, 2500 A

Description

② Interrogation lever
③ Position indicator for three-position switch
④ Ready-for-service indicator
⑤ Actuating opening for earthing switch (EARTHING/
⑥ Actuating opening for disconnector
⑦ Control gate
Spring-operated/stored-energy mechanism (rotary lever mechanism 90°)

• Application in switch-disconnector panel
• With additional energy store for the function "stored-energy OPEN" after tripping by a
HV HRC fuse-link (striker tripping) or a shunt release

② Position indicator for three-position switch
③ Interrogation lever
④ Actuating opening for earthing switch
⑤ Actuating opening for disconnector
⑥ Control gate
⑦ Ready-for-service indicator
Options for all operating • Motor operating mechanism

mechanisms - Remote operation (standard) applied to terminal
- Local operation by momentary-contact rotary control switch (option)
- Manual operation possible with operating lever
• Shunt release (f-release)
- Spring-operated/stored-energy mechanisms can be equipped with a shunt release. Remote
electrical tripping of the three-position switch-disconnector is possible via the magnetic coil
of the shunt release, e.g. transformer overtemperature tripping.
• Wiring
- Auxiliary switches, motor operating mechanisms or shunt releases are wired to terminal
strips in the low-voltage compartment.
9.6 Voltage transformers 4MT

In NXPLUS C switchgear, voltage transformers type 4MT2 and type 4MR can be mounted
optionally.
Common features • According to VDE 0414-9-3 and IEC 61869-3

• Cast-resin insulated
• Inductive type
• Arranged outside the primary enclosure (switchgear vessel)
Mounting locations • At the busbar (4MT2)

Description
• At the panel connection (4MT3)
Voltage transformer types • Busbar voltage transformer

- Pluggable in the cross pieces of the busbar using adapters
- No separate metering panel required
- Repeat test at 80% of the rated short-duration power-frequency withstand voltage possible
with mounted voltage transformer
• Voltage transformer at the panel connection
- Switchable through an SF6-insulated disconnecting facility in the switchgear vessel
- Positions: "CLOSED" and "EARTHED"
- Operation of the disconnecting facility from outside through a metal bellows welded in the
switchgear vessel
- Voltage testing of switchgear and cables possible with mounted and earthed voltage
transformer
- Not suitable for 80% of the rated short-duration power-frequency withstand voltage
(disconnect and earth voltage transformer through disconnecting facility)

Description
Electrical data
Primary data for types 4MT3 and 4MT2

For operating voltages from 3.3 to 23 kV, rated voltage factor Un/8h = 1.9; Un/continuous = 1.2
Rated voltage [kV] Rated short-duration power- Rated lightning impulse Standar Operating voltage [kV]
frequency withstand voltage withstand voltage [kV] d
[kV]
3.6 10 20 IEC 3.3/ √ 3
7.2 20 60 IEC 3.6/ √ 3; 4.0/ √ 3; 4.16/ √ 3; 4.2 √ 3; 4.8/ √ 3;
5.0 √ 3; 5.5/ √ 3; 6.0/ √ 3; 6.24/ √ 3; 6.3/ √ 3;
6.6/ √ 3; 6.9/ √ 3
32 60 GOST 6.0/ √ 3; 6.3/ √ 3; 6.6/ √ 3
12 28 75 IEC 7.2/ √ 3; 7.6/ √ 3; 8.0/ √ 3; 8.3/ √ 3; 8.4/ √
3;8.9/ √ 3; 10/ √ 3; 10.5/ √ 3; 11/ √ 3; 11.4/ √
3; 11.5/ √ 3; 11.6/ √ 3
38 75 GOST 10/ √ 3; 10.5/ √ 3; 11/ √ 3
42 75 GB 10/ √ 3; 10.5/ √ 3; 11/ √ 3
17.5 38 95 IEC 12/ √ 3; 12.4/ √ 3; 12.47/ √ 3; 12.5/ √ 3; 12.8/
√ 3; 13.2/ √ 3; 13.4/ √ 3; 13.8/ √ 3; 14.4/ √ 3;
15/ √ 3; 15.8/ √ 3; 16/ √ 3; 17/ √ 3
24 50 125 IEC 17.5/ √ 3; 18/ √ 3; 19/ √ 3;20/ √ 3; 22/ √ 3; 23/
√ 3
GOST: Russian standard, GB: Chinese standard
Secondary data
For type Operating voltage Auxiliary Thermal limit Rated long- Rating at accuracy class [VA]
[V] winding current time current 0.2 0.5 1 3
(measuring 8h
winding)
4MT3 100/ √ 3; 100/ √ 3; 6 4 IEC
110/ √ 3; 110/ √ 3 10, 15, 20, 25, 30 10, 15, 20, 25, 10, 15, 20, 25, 10, 15, 20, 25,
120/ √ 3 120/ √ 3 30, 45, 50, 60, 30, 45, 50, 60, 30, 45, 50, 60,
75, 90 75, 90, 100, 75, 90, 100,
120, 150, 180 120, 150, 180
GOST 32/60 kV
10, 15, 20, 25, 30 10, 15, 20, 25, 10, 15, 20, 25, 10, 15, 20, 25,
30, 45, 50, 60, 30, 45, 50, 60, 30, 45, 50, 60,
75, 90 75, 90, 100, 75, 90, 100,
120, 150, 180 120, 150, 180
GOST 42/75 kV, GB 42/75 kV
10, 15, 20, 25 10, 15, 20, 25, 10, 15, 20, 25, 10, 15, 20, 25,
30, 45, 50, 60, 30, 45, 50, 60, 30, 45, 50, 60,
75 75, 90, 100, 75, 90, 100,
120, 150 120, 150
4MT2 100/ √ 3; 100/ √ 3; 8 6 IEC
110/ √ 3; 110/ √ 3; 5, 10, 15, 20, 25 10, 15, 20, 25, 10, 15, 20, 25, 10, 15, 20, 25,
120/ √ 3 120/ √ 3 30, 45 30, 45, 50, 60, 30, 45, 50, 60,
75 75
GOST 32/60 kV
5 10, 15 10, 15, 20, 25, 10, 15, 20, 25,
30 30
GOST 42/75 kV, GB 42/75 kV
5, 10 10, 15, 20, 25, 10, 15, 20, 25, 10, 15, 20, 25,
30 30, 45, 50, 60 30, 45, 50, 60
GOST: Russian standard, GB: Chinese standard
Conformity of voltage The voltage transformer can be used as measuring transformer.

transformers
The approval symbol for the voltage transformer is located on the type plate. The approval
symbol is valid throughout the entire service life of the voltage transformer.
Observe deviating country-specific statutory regulations, if applicable.
For an inspection by a calibration office or an officially recognized inspecting authority, the
test adapter (802-8061.3) shown below can be mounted on the voltage transformer 4MT3.

Description
① Secondary lead
② Connection of measuring
equipment
Fig. 23: Mounting the test adapter on voltage transformer

4MT3
The test adapter can be procured from the regional Siemens representative.
9.7 Current transformers 4MC
Features • According to IEC 60044-1 and VDE 0414 Part 1

• Designed as ring-core current transformers:
- Ring core as carrier of secondary winding
- Main circuit corresponds to primary winding
• Arranged outside the primary enclosure (switchgear vessel) due to single-pole design of
cable connection and busbar
• Free of dielectrically stressed cast-resin parts (due to design)
Mounting locations • Around the busbar

• At the panel connection
• Around the cable
Current transformer types • Busbar current transformer

- Inside diameter of transformer 56 mm
- Usable height for 1250 A busbar: 170 mm
- Usable height for 1600 A, 2000 A, 2500 A busbar: 90 mm
• Feeder current transformer
- Max. usable height 214 mm

Description
• Cable-type current transformer

- Max. usable height 170 mm
Electrical data of current transformer type 4MC
Operating voltage max. 0.8 kV

Rated short-duration power- frequency withstand 3 kV
voltage (winding test)
Rated frequency 50/60 Hz
Rated continuous thermal current 1.0 / 1.2 / 1.33 / 1.5 / 2.0 x rated current (primary)
Rated short-time thermal current, max. 3 s 31.5 kA
Rated current dynamic unlimited
primary 40 A to 2500 A
secondary 1 A and 5 A
Multiratio (secondary) 200 - 100 A to 2500 - 1250 A
Core data dependent on rated primary current max. 3 cores
Measuring core Rating 2.5 VA to 30 VA
Class 0.2; 0.5; 1
Overcurrent FS5, FS10
factor
Protection core Rating 2.5 VA to 30 VA
Class 5P or 10P
Overcurrent 10 to 30
factor
Permissible ambient air temperature max. 60 °C
Insulation class E
9.8 HV HRC fuse assembly
① Bushing
② Switchgear vessel
③ Sealing cover with seal
④ Tripping pin for spring-operated/
stored-energy mechanism
⑤ Striker of the HV HRC fuse-link
and articulation for tripping the
spring-operated/stored-energy
mechanism
⑥ HV HRC fuse-link
⑦ Fuse box
Features • With fuse slide for fuse replacement without tools

• HV HRC fuse-links according to DIN 43625 (main dimensions) with striker in "medium"
version according to IEC 60282-1
- as short-circuit protection before transformers or motors,
- with selectivity to upstream and downstream connected equipment,
- 1-pole insulated
• Reference dimension e of the fuse-links
- Ur = 12 kV: e = 292 mm (option e = 442 mm)
- Ur = 24 kV: e = 442 mm
• Requirements according to IEC 62271-105 / VDE 0671-105 met for HV HRC fuse-links in
combination with the three-position switch-disconnector
• Thermal striker tripping when the corresponding HV HRC fuse-link is used
• Climate-independent and maintenance-free, with fuse boxes made of cast resin
• Arrangement of the HV HRC fuse assembly underneath the switching-device vessel
• HV HRC fuse assembly connected to the three-position switch-disconnector / vacuum
contactor via welded-in bushings and connecting bars

Description
• Fuse replacement is only possible when the feeder is earthed

• Option for HV HRC fuse-links: "Tripped" indication for remote electrical indication with a
NO contact
Mode of operation If a HV HRC fuse-link operates, the switch is tripped via an articulation which is integrated into
the cover of the fuse box.
Thermal protection If the fuse tripping fails, the sudden overpressure trips the switch via a diaphragm and the
articulation situated in the cover of the fuse box.
The thermal protection works independently of the type and design of the HV HRC fuse-link
used. The thermal protection is maintenance-free and independent of any outside climatic
effects.
Basic scheme of fuse

tripping
HV HRC fuse-link in service condition
Fuse tripping through striker of HV HRC fuse-link
Fuse tripping due to sudden overpressure in the

fuse box
The HV HRC fuse-links make SIBA (see page 61, "Selection of HV HRC fuse-links") release the
striker depending on the temperature and trip the switch-disconnector as early as in the
overload range of the fuses. Impermissible heating of the fuse box can be avoided in this way.
9.9 Busbar system
Fig. 24: 1250 A busbar system Fig. 25: 1600 A, 2000 A, 2500 A busbar
system
The busbar is single-pole insulated with silicone rubber. Each phase has an earthed layer on
the outside (screened busbar system). This design makes the busbar independent of climatic
effects.
As the busbar system is arranged outside the gas compartment, extension, replacement or
increasing the current carrying capacity by doubling the system is possible within a very short
period of time without requiring any gas work.
To by-pass a removed panel, busbars with double length are available. With these, a defective
panel can be by-passed within a few hours, and switchgear operation can continue.

Description
9.10 Cable connection
Possible combinations of cable connection types (T-plugs, coupling inserts) and

surge arresters up to 24 kV
NOTICE
Flashovers due to incompatible plug combinations
Can damage the switchgear.
➭ Use the same makes for combining plug types, surge arresters and limiters.
For gas-insulated switchgear NXPLUS C, only cable plugs shielded by means of an external
conductive layer (also called screened cable T-plugs) can be used. This external semi-
conductive layer must be earthed. Earthing is normally done through a cable connection.
Insulated cable T-plugs (without external conductive layer) are not permissible, as partial
discharges can arise very quickly due to the proximity to earthed parts. Partial discharges
destroy the cable T-plug, causing an arc between phase and earth.
The connection of conventional cable sealing ends with elbow adapters (e.g. type AKE) is not
permissible, as this connection system is insulated and not screened (no external conductive
layer).

Description
Installation possibilities for cable connections and surge arresters, single-core PE- and XLPE-insulated
Circuit-breaker panel 630 A, 1000 A ● Switch-disconnector panel 630 A ● Disconnector panel 1000 A ● Ring-main panel 630 A ● Vacuum
contactor panel ● Circuit-breaker panel with top-rear cable connection 1250 A 1
Panel spacing 600 mm
Make Conductor Cable T-plugs Coupling inserts/ Surge arresters with coupling inserts According to
cross- coupling plugs standard
Insulation
section2
[mm2] bolted bolted with arresters Coupling inserts • GOST

(Russia, CIS)
12 kV 12 kV additionally
24 kV* 24 kV* • GB/DL (China)
1 cable per panel and phase

Nexans 35…300 EPDM 1x 430TB/G - 300SA-5(10)SA - IEC, GOST, GB/DL
Euromold 1x K430TB/G* - 300SA-5(10)SA - IEC
1x K430TB/G-CSxxx* - 300SA-5(10)SA - GOST, GB/DL
35…300 EPDM 1x 480TB/G - 800SA-10-xxx - IEC, GOST, GB/DL
1x K480TB/G* - 800SA-10-xxx - IEC
50…630 EPDM 1x 484TB/G - 800SA-10-xxx - IEC
35…630 1x K484TB/G* - 800SA-10-xxx - IEC
1x K489TB/G* - 800SA-10-xxx - IEC
Südkabel 50…300 Silicon 1x SET 12 - MUT 23 - IEC, GOST, GB/DL
25…240 e 1x SET 24* - MUT 23 - IEC, GOST, GB/DL
300…500 Silicon 1x SEHDT 13 - MUT 23 - IEC, GOST, GB/DL
300…630 e 1x SEHDT 23* - MUT 23 - IEC, GOST, GB/DL
nkt cables 25…300 Silicon 1x CB 12-630 - CSA 12-x - IEC
25…500 e 1x CB 17,5-630 - CSA 17,5-x - GOST, GB/DL
25…300 1x CB 24-630* - CSA 24-x - IEC, GOST, GB/DL
185…500 Silicon 1x CB 24-1250-2 - CSA 12-x - IEC
95…500 e 1x CB 24-1250-2* - CSA 24-x - IEC
400…630 Silicon 1x CB 36-630(1250) - CSA 12-x - IEC, GOST, GB/DL
e 1x CB 36-630(1250)* - CSA 24-x - IEC, GOST, GB/DL
e 1x CB 42-1250-3* - CSA 24-x - IEC
Tyco 25…300 Silicon 1x RSTI-58xx - RSTI-CC-58SAxxxx - IEC
Electronics e 1x RSTI-58xx* - RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
Raychem
25…300 Silicon 1x RSTI-58xx-CEE01 - RSTI-CC-58SAxxxx - GOST
e 1x RSTI-58xx-CEE01* - RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
400…800 Silicon 1x RSTI-395x - RSTI-CC-58SAxxxx RSTI-SA-PIN IEC
e 1x RSTI-595x* - RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
400…800 Silicon 1x RSTI-595x-CEE01 - RSTI-CC-58SAxxxx RSTI-SA-PIN GOST
e 1x RSTI-595x-CEE01* - RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
3M 50…240 Silicon 1x 93-EE 705-6 - - - IEC, GOST, GB/DL
25…240 e 1x 93-EE 705-6* - - - IEC, GOST, GB/DL
300…400 Silicon 1x 93-EE 715-6 - - - IEC, GOST, GB/DL
e 1x 93-EE 715-6* - - - IEC, GOST, GB/DL
GCA 35…500 Silicon 1x CJB10-630 - - - GB/DL
25…500 e 1x CJB20-630* - - - GB/DL
ABB 25…630 EPDM 1x CSE-A 12630-xx - - - IEC, GOST
Kabeldon 1x CSE-A 24630-xx* - - - IEC, GOST
Cellpack 50…400 EPDM 1x CTS 630A 24kV - CTKSA - IEC
25…300 1x CTS 630A 24kV* - CTKSA - IEC
Ample 25…400 EPDM 1x AQT3-15/630 - AHY5WZ7 - GB/DL
35…500 1x AQT3-24/630* - AHY5WZ7 - GB/DL

Description
Insulation
section2
[mm2 ] bolted bolted with arresters Coupling inserts • GOST

(Russia, CIS)
2 cables per panel and phase

Nexans 35…300 EPDM 1x 430TB/G 1x 300PB/G 300SA-5(10)SA - IEC, GOST, GB/DL
Euromold 1x K430TB/G* 1x K300PB/G* 300SA-5(10)SA - IEC
1x K430TB/G-CSxxx* 1x K300PB/G-CSxxx* 300SA-5(10)SA - GOST, GB/DL
35…300 EPDM 2x 480TB/G 1x 800PB/G 800SA-10-xxx - IEC, GOST, GB/DL
2x K40TB/G* 1x K800PB/G* 800SA-10-xxx - IEC
50…630 EPDM 1x 484TB/G 1x 804PB/G 800SA-10-xxx - IEC
35…630 1x K484TB/G* 1x K804PB/G* 800SA-10-xxx - IEC
Südkabel 50…300 Silicon 1x SET 12 1x SEHDK 13.1 - - IEC, GOST, GB/DL
25…240 e 1x SET 24* 1x SEHDK 23.1* - - IEC, GOST, GB/DL
50…300 Silicon 2x SET 12 1x KU 23.2 - - IEC, GOST, GB/DL
25…240 e 2x SET 24* 1x KU 23.2* - - IEC, GOST, GB/DL
300…500 Silicon 2x SEHDT 13 1x KU 23 - - IEC, GOST, GB/DL
300…630 e 2x SEHDT 23* 1x KU 23* - - IEC, GOST, GB/DL
nkt cables 25…300 Silicon 1x CB 12-630 1x CC 12-630 CSA 12-x - IEC
25…500 e 1x CB 17,5-630 1x CC 17,5-630 CSA 17,5-x - GOST, GB/DL
25…300 1x CB 24-630* 1x CC 24-630* CSA 24-x - IEC, GOST, GB/DL
25…300 Silicon 2x CB 12-630 1x CP 630-C CSA 12-x - IEC
e 2x CB 24-630* 1x CP 630-C* CSA 24-x - IEC, GOST, GB/DL
185…500 Silicon 1x CB 24-1250-2 1x CC 24-1250-2 CSA 12-x - IEC
95…500 e 1x CB 24-1250-2* 1x CC 24-1250-2* CSA 24-x - IEC
185…500 Silicon 2x CB 24-1250-2 1x CP 630-C CSA 12-x - IEC
95…500 e 2x CB 24-1250-2* 1x CP 630-C* CSA 24-x - IEC
400…630 Silicon 1x CB 36-630(1250) 1x CC 36-630(1250) CSA 12-x - IEC, GOST, GB/DL
e 1x CB 36-630(1250)* 1x CC 36-630(1250)* CSA 24-x - IEC, GOST, GB/DL
400…630 Silicon 2x CB 36-630(1250) 1x CP 630-M16 CSA 12-x - IEC, GOST, GB/DL
e 2x CB 36-630(1250)* 1x CP 630-M16* CSA 24-x - IEC, GOST, GB/DL
e 1x CB 42-1250-3* 1x CC 42-2500-3* CSA 24-x - IEC
Tyco 25…300 Silicon 1x RSTI-58xx 1x RSTI-CC-58xx RSTI-CC-58SAxxxx - IEC
Electronics e 1x RSTI-58xx* 1x RSTI-CC-58xx* RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
Raychem
25…300 Silicon 1x RSTI-58xx-CEE01 1x RSTI-CC-58xx-CEE01 RSTI-CC-58SAxxxx - GOST
e 1x RSTI-58xx-CEE01* 1x RSTI-CC-58xx-CEE01* RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
400…800 Silicon 1x RSTI-395x 1x RSTI-CC-395x RSTI-CC-58SAxxxx RSTI-SA-PIN IEC
e 1x RSTI-595x* 1x RSTI-CC-595x* RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
400…800 Silicon 1x RSTI-595x-CEE01 1x RSTI-CC-595x-CEE01 RSTI-CC-58SAxxxx RSTI-SA-PIN GOST
e 1x RSTI-595x-CEE01* 1x RSTI-CC-595x-CEE01* RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
3M 50…240 Silicon 2x 93-EE 705-6 1x KU 23.2 - - IEC, GOST, GB/DL
25…240 e 2x 93-EE 705-6* 1x KU 23.2* - - IEC, GOST, GB/DL
240 Silicon 1x 93-EE 705-6 1x 93-EE 718-6 - - IEC, GOST, GB/DL
150…240 e 1x 93-EE 705-6* 1x 93-EE 718-6* - - IEC, GOST, GB/DL
300…400 Silicon 2x 93-EE 715-6 1x KU 23.2 - - IEC, GOST, GB/DL
e 2x 93-EE 715-6* 1x KU 23.2* - - IEC, GOST, GB/DL
GCA 35…500 Silicon 1x CJB10-630 1x CJBK10-630 - - GB/DL
25…500 e 1x CJB20-630* 1x CJBK20-630* - - GB/DL
ABB 25…630 EPDM 2x CSE-A 12630-xx 1x PC 630-3 - - IEC, GOST
Kabeldon 2x CSE-A 24630-xx* 1x PC 630-3* - - IEC, GOST

Description
Insulation
section2
[mm2] bolted bolted with arresters Coupling inserts • GOST

(Russia, CIS)
Cellpack 50…400 EPDM 2x CTS 630A 24kV 1x CKS 630A 24kV - - IEC
25…300 2x CTS 630A 24kV* 1x CKS 630A 24kV* - - IEC
50…240 EPDM 1x CTS 630A 24kV 1x CTKS 630A 24kV CTKSA - IEC
25…240 1x CTS 630A 24kV* 1x CTKS 630A 24kV* CTKSA - IEC
Ample 25…400 EPDM 1x AQT3-15/630 1x AHT3-15/630 AHY5WZ7 - GB/DL
35…500 1x AQT3-24/630* 1x AHT3-24/630* AHY5WZ7 - GB/DL
Nexans 35…300 EPDM 1x 430TB/G 2x 300PB/G - - IEC, GOST, GB/DL
Euromold 1x K430TB/G* 2x K300PB/G* - - IEC
1x K430TB/G-CSxxx* 2x K300PB/G-CSxxx* - - GOST, GB/DL
35…300 EPDM 1x 480TB/G 2x 800PB/G - - IEC
1x K480TB/G* 2x K800PB/G* - - IEC
35…630 1x K484TB/G* 2x K804PB/G* - - IEC
1x K489TB/G* 2x K809PB/G* - - IEC
nkt cables 25…300 Silicon 1x CB 12-630 2x CC 12-630 - - IEC
25…500 e 1x CB 17,5-630 2x CC 17,5-630 - - GOST, GB/DL
25…300 1x CB 24-630* 2x CC 24-630* - - IEC, GOST, GB/DL
185…500 Silicon 1x CB 24-1250-2 2x CC 24-1250-2 - - IEC
95…500 e 1x CB 24-1250-2* 2x CC 24-1250-2* - - IEC
400…630 Silicon 1x CB 36-630(1250) 2x CC 36-630(1250) - - IEC, GOST, GB/DL
e 1x CB 36-630(1250)* 2x CC 36-630(1250)* - - IEC, GOST, GB/DL
e 1x CB 42-1250-3* 2x CC 42-2500-3* - - IEC
Tyco 25…300 Silicon 1x RSTI-58xx 2x RSTI-CC-58xx - - IEC
Electronics e 1x RSTI-58xx* 2x RSTI-CC-58xx* - - IEC
Raychem
25…300 Silicon 1x RSTI-58xx-CEE01 2x RSTI-CC-58xx-CEE01 - - GOST
e 1x RSTI-58xx-CEE01* 2x RSTI-CC-58xx-CEE01* - - GOST
400…800 Silicon 1x RSTI-395x 2x RSTI-CC-395x - - IEC
e 1x RSTI-595x* 2x RSTI-CC-595x* - - IEC
400…800 Silicon 1x RSTI-595x-CEE01 2x RSTI-CC-595x-CEE01 - - GOST
e 1x RSTI-595x-CEE01* 2x RSTI-CC-595x-CEE01* - - GOST
Cellpack 50…240 EPDM 1x CTS 630A 24kV 2x CTKS 630A 24kV - - IEC
25…240 1x CTS 630A 24kV* 2x CTKS 630A 24kV* - - IEC
1
At a continuous current of more than 1150 A, cable sealing ends with tin-plated, nickel-plated or silver-plated cable lugs are required.
2
Observe the actual current- and short-circuit-carrying capacity of the cables and sealing ends.

Description
Circuit-breaker panel 1250 A1 ● Disconnector panel 1250 A1
Insulation
section2
[mm2 ] bolted bolted Arresters Coupling inserts • GOST

(Russia, CIS)

1x K480TB/G* - 800SA-10-xxx - IEC
35…630 1x K484TB/G* - 800SA-10-xxx - IEC
1x K489TB/G* - 800SA-10-xxx - IEC
Südkabel 50…300 Silicon 1x SET 12 - MUT 23 - IEC, GOST, GB/DL
25…240 e 1x SET 24* - MUT 23 - IEC, GOST, GB/DL
300…500 Silicon 1x SEHDT 13 - MUT 23 - IEC, GOST, GB/DL
300…630 e 1x SEHDT 23* - MUT 23 - IEC, GOST, GB/DL
nkt cables 25…300 Silicon 1x CB 12-630 - CSA 12-x - IEC
25…500 e 1x CB 17,5-630 - CSA 17,5-x - GOST, GB/DL
95…500 e 1x CB 24-1250-2* - CSA 24-x - IEC
400…630 Silicon 1x CB 36-630(1250) - CSA 12-x - IEC, GOST, GB/DL
e 1x CB 36-630(1250)* - CSA 24-x - IEC, GOST, GB/DL
e 1x CB 42-1250-3* - CSA 24-x - IEC
Tyco 25…300 Silicon 1x RSTI-58xx - RSTI-CC-58SAxxxx - IEC
Electronics e 1x RSTI-58xx* - RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
Raychem 25…300 Silicon 1x RSTI-58xx-CEE01 - RSTI-CC-58SAxxxx - GOST
e 1x RSTI-58xx-CEE01* - RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
400…800 Silicon 1x RSTI-395x - RSTI-CC-58SAxxxx RSTI-SA-PIN IEC
e 1x RSTI-595x* - RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
400…800 Silicon 1x RSTI-595x-CEE01 - RSTI-CC-58SAxxxx RSTI-SA-PIN GOST
e 1x RSTI-595x-CEE01* - RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
3M 50…240 Silicon 1x 93-EE 705-6 - - - IEC, GOST, GB/DL
25…240 e 1x 93-EE 705-6* - - - IEC, GOST, GB/DL
300…400 Silicon 1x 93-EE 715-6 - - - IEC, GOST, GB/DL
e 1x 93-EE 715-6* - - - IEC, GOST, GB/DL
GCA 35…500 Silicon 1x CJB10-630 - - - GB
25…500 e 1x CJB20-630* - - - GB

35…500 1x AQT3-24/630* - AHY5WZ7 - GB/DL

Description
Insulation
section2
[mm2] bolted bolted Arresters Coupling inserts • GOST

(Russia, CIS)

Südkabel 50…300 Silicon 1x SET 12 1x SEHDK 13.1 MUT 23 - IEC, GOST, GB/DL
25…240 e 1x SET 24* 1x SEHDK 23.1* MUT 23 - IEC, GOST, GB/DL
50…300 Silicon 2x SET 12 1x KU 23.2 MUT 23 - IEC, GOST, GB/DL
25…240 e 2x SET 24* 1x KU 23.2* MUT 23 - IEC, GOST, GB/DL
300…500 Silicon 2x SEHDT 13 1x KU 23 MUT 23 - IEC, GOST, GB/DL
300…630 e 2x SEHDT 23* 1x KU 23* MUT 23 - IEC, GOST, GB/DL
25…300 Silicon 2x CB 12-630 1x CP 630-C CSA 12-x - IEC
e 2x CB 24-630* 1x CP 630-C* CSA 24-x - IEC, GOST, GB/DL
95…500 e 1x CB 24-1250-2* 1x CC 24-1250-2* CSA 24-x - IEC
185…500 Silicon 2x CB 24-1250-2 1x CP 630-C CSA 12-x - IEC
95…500 e 2x CB 24-1250-2* 1x CP 630-C* CSA 24-x - IEC
400…630 Silicon 2x CB 36-630(1250) 1x CP 630-M16 CSA 12-x - IEC, GOST, GB/DL
e 2x CB 36-630(1250)* 1x CP 630-M16* CSA 24-x - IEC, GOST, GB/DL
e 1x CB 42-1250-3* 1x CC 42-2500-3* CSA 24-x - IEC
Raychem
3M 50…240 Silicon 2x 93-EE 705-6 1x KU 23.2 - - IEC, GOST, GB/DL
25…240 e 2x 93-EE 705-6* 1x KU 23.2* - - IEC, GOST, GB/DL
240 Silicon 1x 93-EE 705-6 1x 93-EE 718-6 - - IEC, GOST, GB/DL
150…240 e 1x 93-EE 705-6* 1x 93-EE 718-6* - - IEC, GOST, GB/DL
300…400 Silicon 2x 93-EE 715-6 1x KU 23.2 - - IEC, GOST, GB/DL
e 2x 93-EE 715-6* 1x KU 23.2* - - IEC, GOST, GB/DL
GCA 35…500 Silicon 1x CJB10-630 1x CJBK10-630 - - GB
25…500 e 1x CJB20-630* 1x CJBK20-630* - - GB

Description
Insulation
section2

(Russia, CIS)
Cellpack 50…400 EPDM 2x CTS 630A 24kV 1x CKS 630A 24kV CTKSA - IEC
25…300 2x CTS 630A 24kV* 1x CKS 630A 24kV* CTKSA - IEC
25…300 Silicon 3x CB 12-630 2x CP 630-C - - IEC
e 3x CB 24-630* 2x CP 630-C* - - IEC, GOST, GB/DL
95…500 e 1x CB 24-1250-2* 2x CC 24-1250-2* CSA 24-x - IEC
185…500 Silicon 3x CB 24-1250-2 2x CP 630-C - - IEC
95…500 e 3x CB 24-1250-2* 2x CP 630-C* - - IEC
400…630 Silicon 3x CB 36-630(1250) 2x CP 630-M16 - - IEC, GOST, GB/DL
e 3x CB 36-630(1250)* 2x CP 630-M16* - - IEC, GOST, GB/DL
e 1x CB 42-1250-3* 2x CC 42-2500-3* CSA 24-x - IEC
Raychem
1x K480TB/G* 3x K800PB/G* - - IEC
35…630 1x K484TB/G* 3x K804PB/G* - - IEC
1x K489TB/G* 3x K809PB/G* - - IEC

Description
Insulation
section2

(Russia, CIS)
nkt cables 185…500 Silicon 1x CB 24-1250-2 3x CC 24-1250-2 - - IEC

95…500 e 1x CB 24-1250-2* 3x CC 24-1250-2* - - IEC
e 1x CB 42-1250-3* 3x CC 42-2500-3* - - IEC
Tyco 25…300 Silicon 1x RSTI-58xx 3x RSTI-CC-58xx - - IEC
Electronics e 1x RSTI-58xx* 3x RSTI-CC-58xx* - - IEC
Raychem 25…300 Silicon 1x RSTI-58xx-CEE1 3x RSTI-CC-58xx-CEE1 - - GOST
e 1x RSTI-58xx-CEE1* 3x RSTI-CC-58xx-CEE1* - - GOST
1
2

Description
Circuit-breaker panel and disconnector panel 2000 A, 2500 A (panel spacing 900 mm)
Make Conductor Cable T-plugs Coupling inserts/ Surge arresters with According to
Insulation
section1

(Russia, CIS)

2x K480TB/G* - 800SA-10-xxx - IEC
35…630 2x K484TB/G* - 800SA-10-xxx - IEC
Südkabel 50…300 Silicone 2x SET 12 - MUT 23 - IEC, GOST, GB/DL
25…240 2x SET 24* - MUT 23 - IEC, GOST, GB/DL
300…500 Silicone 2x SEHDT 13 - MUT 23 - IEC, GOST, GB/DL
300…630 2x SEHDT 23* - MUT 23 - IEC, GOST, GB/DL
nkt cables 25…300 Silicone 2x CB 12-630 - CSA 12-x - IEC
25…500 2x CB 17.5-630 - CSA 17.5-x - GOST, GB/DL
185…500 Silicone 2x CB 24-1250-2 - CSA 12-x - IEC
95…500 2x CB 24-1250-2* - CSA 24-x - IEC
400…630 Silicone 2x CB 36-630(1250) - CSA 12-x - IEC, GOST, GB/DL
2x CB 36-630(1250)* - CSA 24-x - IEC, GOST, GB/DL
Tyco 25…300 Silicone 2x RSTI-58xx - RSTI-CC-58SAxxxx - IEC
Electronics 2x RSTI-58xx* - RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
Raychem
25…300 Silicone 2x RSTI-58xx-CEE01 - RSTI-CC-58SAxxxx - GOST
2x RSTI-58xx-CEE01* - RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
400…800 Silicone 2x RSTI-395x - RSTI-CC-58SAxxxx RSTI-SA-PIN IEC
2x RSTI-595x* - RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
400…800 Silicone 2x RSTI-595x-CEE01 - RSTI-CC-58SAxxxx RSTI-SA-PIN GOST
2x RSTI-595x-CEE01* - RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
3M 50…240 Silicone 2x 93-EE 705-6 - - - IEC, GOST, GB/DL
25…240 2x 93-EE 705-6* - - - IEC, GOST, GB/DL
300…400 Silicone 2x 93-EE 715-6 - - - IEC, GOST, GB/DL
2x 93-EE 715-6* - - - IEC, GOST, GB/DL
GCA 35…500 Silicone 2x CJB10-630 - - - GB
25…500 2x CJB20-630* - - - GB
35…500 2x AQT3-24/630* - AHY5WZ7 - GB/DL

Description
Insulation
section1

(Russia, CIS)
Südkabel 50…300 Silicone 2x SET 12 2x SEHDK 13.1 MUT 23 - IEC, GOST, GB/DL
25…240 2x SET 24* 2x SEHDK 23.1* MUT 23 - IEC, GOST, GB/DL
50…300 Silicone 4x SET 12 2x KU 23.2 MUT 23 - IEC, GOST, GB/DL
25…240 4x SET 24* 2x KU 23.2* MUT 23 - IEC, GOST, GB/DL
300…500 Silicone 4x SEHDT 13 2x KU 23 MUT 23 - IEC, GOST, GB/DL
300…630 4x SEHDT 23* 2x KU 23* MUT 23 - IEC, GOST, GB/DL
nkt cables 25…300 Silicone 2x CB 12-630 2x CC 12-630 CSA 12-x - IEC
25…500 2x CB 17.5-630 2x CC 12-630 CSA 17.5-x - GOST, GB/DL
25…300 Silicone 4x CB 12-630 2x CP 630-C CSA 12-x - IEC
4x CB 24-630* 2x CP 630-C* CSA 24-x - IEC, GOST, GB/DL
185…500 Silicone 2x CB 24-1250-2 2x CC 24-1250-2 CSA 12-x - IEC
95…500 2x CB 24-1250-2* 2x CC 24-1250-2* CSA 24-x - IEC
185…500 Silicone 4x CB 24-1250-2 2x CP 630-C CSA 12-x - IEC
95…500 4x CB 24-1250-2* 2x CP 630-C* CSA 24-x - IEC
400…630 Silicone 2x CB 36-630(1250) 2x CC 36-630(1250) CSA 12-x - IEC, GOST, GB/DL
2x CB 36-630(1250)* 2x CC 36-630(1250)* CSA 24-x - IEC, GOST, GB/DL
400…630 Silicone 4x CB 36-630(1250) 2x CP 630-M16 CSA 12-x - IEC, GOST, GB/DL
4x CB 36-630(1250)* 2x CP 630-M16* CSA 24-x - IEC, GOST, GB/DL
Tyco 25…300 Silicone 2x RSTI-58xx 2x RSTI-CC-58xx RSTI-CC-58SAxxxx - IEC
Electronics 2x RSTI-58xx* 2x RSTI-CC-58xx* RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
Raychem 25…300 Silicone 2x RSTI-58xx-CEE01 2x RSTI-CC-58xx-CEE01 RSTI-CC-58SAxxxx - GOST
2x RSTI-58xx-CEE01* 2x RSTI-CC-58xx-CEE01* RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
400…800 Silicone 2x RSTI-395x 2x RSTI-CC-395x RSTI-CC-58SAxxxx RSTI-SA-PIN IEC
2x RSTI-595x* 2x RSTI-CC-595x* RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
400…800 Silicone 2x RSTI-595x-CEE01 2x RSTI-CC-595x-CEE01 RSTI-CC-58SAxxxx RSTI-SA-PIN GOST
2x RSTI-595x-CEE01* 2x RSTI-CC-595x-CEE01* RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
3M 50…240 Silicone 4x 93-EE 705-6 2x KU 23.2 - - IEC, GOST, GB/DL
25…240 4x 93-EE 705-6* 2x KU 23.2* - - IEC, GOST, GB/DL
240 Silicone 2x 93-EE 705-6 2x 93-EE 718-6 - - IEC, GOST, GB/DL
150…240 2x 93-EE 705-6* 2x 93-EE 718-6* - - IEC, GOST, GB/DL
300…400 Silicone 4x 93-EE 715-6 2x KU 23.2 - - IEC, GOST, GB/DL
4x 93-EE 715-6* 2x KU 23.2* - - IEC, GOST, GB/DL
GCA 35…500 Silicone 2x CJB10-630 2x CJBK10-630 - - GB
25…500 2x CJB20-630* 2x CJBK20-630* - - GB
Cellpack 50…400 EPDM 4x CTS 630A 24kV 2x CKS 630A 24kV - - IEC
25…300 4x CTS 630A 24kV* 2x CKS 630A 24kV* - - IEC

Description
Insulation
section1

(Russia, CIS)
nkt cables 25…300 Silicone 2x CB 12-630 4x CC 12-630 CSA 12-x - IEC

25…500 2x CB 17.5-630 4x CC 12-630 CSA 17.5-x - GOST, GB/DL
25…300 Silicone 6x CB 12-630 4x CP 630-C - - IEC
6x CB 24-630* 4x CP 630-C* - - IEC, GOST, GB/DL
185…500 Silicone 2x CB 24-1250-2 4x CC 24-1250-2 CSA 12-x - IEC
95…500 2x CB 24-1250-2* 4x CC 24-1250-2* CSA 24-x - IEC
185…500 Silicone 6x CB 24-1250-2 4x CP 630-C - - IEC
95…500 6x CB 24-1250-2* 4x CP 630-C* - - IEC
400…630 Silicone 2x CB 36-630(1250) 4x CC 36-630(1250) CSA 12-x - IEC, GOST, GB/DL
2x CB 36-630(1250)* 4x CC 36-630(1250)* CSA 24-x - IEC, GOST, GB/DL
Tyco 25…300 Silicone 2x RSTI-58xx 4x RSTI-CC-58xx RSTI-CC-58SAxxxx - IEC
Electronics 2x RSTI-58xx* 4x RSTI-CC-58xx* RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
Raychem
25…300 Silicone 2x RSTI-58xx-CEE01 4x RSTI-CC-58xx-CEE01 RSTI-CC-58SAxxxx - GOST
2x RSTI-58xx-CEE01* 4x RSTI-CC-58xx-CEE01* RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
400…800 Silicone 2x RSTI-395x 4x RSTI-CC-395x RSTI-CC-58SAxxxx RSTI-SA-PIN IEC
2x RSTI-595x* 4x RSTI-CC-595x* RSTI-CC-68SAxxxx RSTI-SA-PIN IEC
400…800 Silicone 2x RSTI-595x-CEE01 4x RSTI-CC-595x-CEE01 RSTI-CC-58SAxxxx RSTI-SA-PIN GOST
2x RSTI-595x-CEE01* 4x RSTI-CC-595x-CEE01* RSTI-CC-68SAxxxx RSTI-SA-PIN GOST
2x K480TB/G* 6x K800PB/G* - - IEC
35…630 2x K484TB/G* 6x K804PB/G* - - IEC
nkt cables 185…500 Silicone 2x CB 24-1250-2 6x CC 24-1250-2 - - IEC
95…500 2x CB 24-1250-2* 6x CC 24-1250-2* - - IEC
Tyco 25…300 Silicone 2x RSTI-58xx 6x RSTI-CC-58xx - - IEC
Electronics 2x RSTI-58xx 6x RSTI-CC-58xx - - IEC
Raychem 25…300 Silicone 2x RSTI-58xx-CEE1 6x RSTI-CC-58xx-CEE1 - - GOST
2x RSTI-58xx-CEE1 6x RSTI-CC-58xx-CEE1 - - GOST
1 Observe the actual current- and short-circuit-carrying capacity of the cables and sealing ends.

Description
Installation possibilities for cable connections and surge arresters, three-core PE- and XLPE-insulated
Make Conductor Cable T-plugs Coupling inserts/ Distribution kit for Surge arresters According to
cross- Insulation coupling plugs three-core cables standard
section2
[mm2] bolted bolted additionally • GOST (Russia,

CIS)
12 kV 12 kV
• GB/DL (China)
24 kV* 24 kV*
Nexans 35…300 EPDM 1x 430TB/G - 1x distribution kit 300SA-5(10)SA IEC, GOST, GB/DL
Euromold 1x K430TB/G* - 1x distribution kit* 300SA-5(10)SA IEC
1x K430TB/G-CSxxx* - 1x distribution kit* 300SA-5(10)SA GOST, GB/DL
35…300 EPDM 1x 480TB/G - 1x distribution kit 800SA-10-xxx IEC, GOST, GB/DL
1x K480TB/G* - 1x distribution kit* 800SA-10-xxx IEC
Südkabel 50…300 Silicon 1x SET 12 - 1x distribution kit SAT MUT 23 IEC, GOST, GB/DL
25…240 e 1x SET 24* - 1x distribution kit SAT* MUT 23 IEC, GOST, GB/DL
nkt cables 25…300 Silicon 1x CB 12-630 - 1x distribution kit ATS CSA 12-x IEC
25…500 e 1x CB 17,5-630 - 1x distribution kit ATS CSA 17,5-x GOST, GB/DL
25…300 1x CB 24-630* - 1x distribution kit ATS* CSA 24-x IEC, GOST, GB/DL
185…500 Silicon 1x CB 24-1250-2 - 1x distribution kit ATS CSA 12-x IEC
95…500 e 1x CB 24-1250-2* - 1x distribution kit ATS* CSA 24-x IEC
Tyco 25…300 Silicon 1x RSTI-58xx - 1x distribution kit RSTI- RSTI-CC-58SAxxxx IEC
Electronics e TRF0x
Raychem 1x RSTI-58xx* - 1x distribution kit RSTI- RSTI-CC-68SAxxxx IEC
TRF0x*
25…300 Silicon 1x RSTI-58xx-CEE01 - 1x distribution kit RSTI- RSTI-CC-58SAxxxx GOST
e TRF0x
1x RSTI-58xx-CEE01* - 1x distribution kit RSTI- RSTI-CC-68SAxxxx GOST
TRF0x*
3M 50…240 Silicon 1x 93-EE 705-6 - 1x distribution kit - IEC, GOST, GB/DL
25…240 e 1x 93-EE 705-6* - 1x distribution kit* - IEC, GOST, GB/DL
300…400 Silicon 1x 93-EE 715-6 - 1x distribution kit - IEC, GOST, GB/DL
e 1x 93-EE 715-6* - 1x distribution kit* - IEC, GOST, GB/DL
GCA 35…500 Silicon 1x CJB10-630 - 1x distribution kit - GB
25…500 e 1x CJB20-630* - 1x distribution kit* - GB
ABB 25…300 EPDM 1x CSE-A 12630-xx - 1x distribution kit - IEC, GOST
Kabeldon 1x CSE-A 24630-xx* - 1x distribution kit* - IEC, GOST
Cellpack 50…400 EPDM 1x CTS 630A 24kV - 1x distribution kit CTKSA IEC
25…300 1x CTS 630A 24kV* - 1x distribution kit* CTKSA IEC
Ample 25…400 EPDM 1x AQT3-15/630 - 1x distribution kit AHY5WZ7 GB/DL
35…500 1x AQT3-24/630* - 1x distribution kit* AHY5WZ7 GB/DL
Nexans 35…300 EPDM 1x 430TB/G 1x 300PB/G 2x distribution kit 300SA-5(10)SA IEC, GOST, GB/DL
Euromold 1x K430TB/G* 1x K300PB/G* 2x distribution kit* 300SA-5(10)SA IEC
1x K430TB/G-CSxxx* 1x K300PB/G-CSxxx* 2x distribution kit* 300SA-5(10)SA GOST, GB/DL
35…300 EPDM 2x 480TB/G 1x 800PB/G 2x distribution kit 800SA-10-xxx IEC, GOST, GB/DL
2x K480TB/G* 1x K800PB/G* 2x distribution kit* 800SA-10-xxx IEC
Südkabel 50…300 Silicon 1x SET 12 1x SEHDK 13.1 2x distribution kit SAT - IEC, GOST, GB/DL
25…240 e 1x SET 24* 1x SEHDK 23.1* 2x distribution kit SAT* - IEC, GOST, GB/DL
50…300 Silicon 2x SET 12 1x KU 23.2 2x distribution kit SAT - IEC, GOST, GB/DL
25…240 e 2x SET 24* 1x KU 23.2* 2x distribution kit SAT* - IEC, GOST, GB/DL

Description
cross- coupling plugs three-core cables standard
Insulation
section2
[mm2 ] bolted bolted additionally • GOST (Russia,

CIS)
12 kV 12 kV
• GB/DL (China)
24 kV* 24 kV*
nkt cables 25…300 Silicon 1x CB 12-630 1x CC 12-630 2x distribution kit ATS CSA 12-x IEC
25…500 e 1x CB 17,5-630 1x CC 17,5-630 2x distribution kit ATS CSA 17,5-x GOST, GB/DL
25…300 1x CB 24-630* 1x CC 24-630* 2x distribution kit ATS* CSA 24-x IEC, GOST, GB/DL
25…300 Silicon 2x CB 12-630 1x CP 630-C 2x distribution kit ATS CSA 12-x IEC
e 2x CB 24-630* 1x CP 630-C* 2x distribution kit ATS* CSA 24-x IEC, GOST, GB/DL
185…500 Silicon 1x CB 24-1250-2 1x CC 24-1250-2 2x distribution kit ATS CSA 12-x IEC
95…500 e 1x CB 24-1250-2* 1x CC 24-1250-2* 2x distribution kit ATS* CSA 24-x IEC
185…500 Silicon 2x CB 24-1250-2 1x CP 630-C 2x distribution kit ATS CSA 12-x IEC
95…500 e 2x CB 24-1250-2* 1x CP 630-C* 2x distribution kit ATS* CSA 24-x IEC
Tyco 25…300 Silicon 1x RSTI-58xx 1x RSTI-CC-58xx 2x distribution kit RSTI- RSTI-CC-58SAxxxx IEC
Electronics e TRF0x
Raychem 1x RSTI-58xx* 1x RSTI-CC-58xx* 2x distribution kit RSTI- RSTI-CC-68SAxxxx IEC
TRF0x*
25…300 Silicon 1x RSTI-58xx-CEE01 1x RSTI-CC-58xx-CEE01 2x distribution kit RSTI- RSTI-CC-58SAxxxx GOST
e TRF0x
1x RSTI-58xx-CEE01* 1x RSTI-CC-58xx- 2x distribution kit RSTI- RSTI-CC-68SAxxxx GOST
CEE01* TRF0x*
3M 50…240 Silicon 2x 93-EE 705-6 1x KU 23.2 2x distribution kit - IEC, GOST, GB/DL
25…240 e 2x 93-EE 705-6* 1x KU 23.2* 2x distribution kit* - IEC, GOST, GB/DL
240 Silicon 1x 93-EE 705-6 1x 93-EE 718-6 2x distribution kit - IEC, GOST, GB/DL
150…240 e 1x 93-EE 705-6* 1x 93-EE 718-6* 2x distribution kit* - IEC, GOST, GB/DL
300…400 Silicon 2x 93-EE 715-6 1x KU 23.2 2x distribution kit - IEC, GOST, GB/DL
e 2x 93-EE 715-6* 1x KU 23.2* 2x distribution kit* - IEC, GOST, GB/DL
GCA 35…500 Silicon 1x CJB10-630 1x CJBK10-630 2x distribution kit - GB
25…500 e 1x CJB20-630* 1x CJBK20-630* 2x distribution kit* - GB
ABB 25…300 EPDM 2x CSE-A 12630-xx 1x PC 630-3 2x distribution kit - IEC, GOST
Kabeldon 2x CSE-A 24630-xx* 1x PC 630-3* 2x distribution kit* - IEC, GOST
Cellpack 50…400 EPDM 2x CTS 630A 24kV 1x CKS 630A 24kV 2x distribution kit - IEC
25…300 2x CTS 630A 24kV* 1x CKS 630A 24kV* 2x distribution kit* - IEC
50…240 EPDM 1x CTS 630A 24kV 1x CTKS 630A 24kV 2x distribution kit CTKSA IEC
25…240 1x CTS 630A 24kV* 1x CTKS 630A 24kV* 2x distribution kit* CTKSA IEC
Ample 25…400 EPDM 1x AQT3-15/630 1x AHT3-15/630 2x distribution kit AHY5WZ7 GB/DL
35…500 1x AQT3-24/630* 1x AHT3-24/630* 2x distribution kit* AHY5WZ7 GB/DL
Nexans 35…300 EPDM 1x 430TB/G 2x 300PB/G 3x distribution kit - IEC, GOST, GB/DL
Euromold 1x K430TB/G* 2x K300PB/G* 3x distribution kit* - IEC
1x K430TB/G-CSxxx* 2x K300PB/G-CSxxx* 3x distribution kit* - GOST, GB/DL
35…300 EPDM 1x 480TB/G 2x 800PB/G 3x distribution kit 800SA-10-xxx IEC, GOST, GB/DL
1x K480TB/G* 2x K800PB/G* 3x distribution kit* 800SA-10-xxx IEC
nkt cables 25…300 Silicon 1x CB 12-630 2x CC 12-630 3x distribution kit ATS - IEC
25…500 e 1x CB 17,5-630 2x CC 17,5-630 3x distribution kit ATS - GOST, GB/DL
25…300 1x CB 24-630* 2x CC 24-630* 3x distribution kit ATS* - IEC, GOST, GB/DL
185…500 Silicon 1x CB 24-1250-2 2x CC 24-1250-2 3x distribution kit ATS - IEC
95…500 e 1x CB 24-1250-2* 2x CC 24-1250-2* 3x distribution kit ATS* - IEC
Tyco 25…300 Silicon 1x RSTI-58xx 2x RSTI-CC-58xx 3x distribution kit RSTI- - IEC
Electronics e TRF0x
Raychem 1x RSTI-58xx* 2x RSTI-CC-58xx* 3x distribution kit RSTI- - IEC
TRF0x*
25…300 Silicon 1x RSTI-58xx-CEE01 2x RSTI-CC-58xx-CEE01 3x distribution kit RSTI- - GOST
e TRF0x
1x RSTI-58xx-CEE01* 2x RSTI-CC-58xx- 3x distribution kit RSTI- - GOST
CEE01* TRF0x*

Description
cross- coupling plugs three-core cables standard
Insulation
section2
[mm2] bolted bolted additionally • GOST (Russia,

CIS)
12 kV 12 kV
• GB/DL (China)
24 kV* 24 kV*
Cellpack 50…240 EPDM 1x CTS 630A 24kV 2x CTKS 630A 24kV 3x distribution kit - IEC
25…240 1x CTS 630A 24kV* 2x CTKS 630A 24kV* 3x distribution kit* - IEC
1
2 Observe the actual current- and short-circuit-carrying capacity of the cables and sealing ends.

Description
Installation possibilities for paper-insulated non-draining cables
contactor panel ● Circuit-breaker panel 1250 A1 ● Disconnector panel 1250 A1
Make Conductor Cable T-plugs Coupling inserts/coupling Distribution kit Surge arresters According to
cross- plugs for three-core standard
Insulation
section 2 cables
[mm2] bolted bolted additionally • GOST

(Russia, CIS)
12 kV 12 kV
• GB/DL (China)
Nexans 35…300 EPDM 1x 430TB/G 1x distribution 300SA-5(10)SA IEC, GOST, GB/DL
-
Euromold kit MIND
nkt cables 25…120 Silicon 1x SÜEV10-120CU-xxxx- CSA 12-x IEC, GOST, GB/DL
- -
e CB24
150…240 Silicon 1x SÜEV10-240CU-xxxx- CSA 12-x IEC, GOST, GB/DL
- -
e CB24
Nexans 35…300 EPDM 1x 430TB/G 1x 300PB/G 2x distribution IEC, GOST, GB/DL
-
Euromold kit MIND
nkt cables 25…120 Silicon 1x SÜEV10-120CU-xxxx- 1x SÜEV10-120CU-xxxx- CSA 12-x IEC, GOST, GB/DL
-
e CB24 CC24
150…240 Silicon 1x SÜEV10-240CU-xxxx- 1x SÜEV10-240CU-xxxx- CSA 12-x IEC, GOST, GB/DL
-
e CB24 CC24
Nexans 35…300 EPDM 1x 430TB/G 2x 300PB/G 3x distribution IEC, GOST, GB/DL
-
Euromold kit MIND
1 At a continuous current of more than 1150 A, cable sealing ends with tin-plated, nickel-plated or silver-plated cable lugs are required.
2
Installation possibilities for paper-insulated mass-impregnated cables
contactor panel ● Circuit-breaker panel 1250 A1 ● Disconnector panel 1250 A1
Make Conductor Cable T-plugs Coupling inserts/ Distribution kit Surge arresters According to
cross- coupling plugs for three-core standard
Insulation
section 2 cables
[mm2] bolted bolted • GOST

(Russia, CIS)
12 kV 12 kV
• GB/DL (China)
nkt cables 25…120 Silicone 1x SÜEV10-120CU- - - CSA 12-x IEC, GOST, GB/DL
xxxx-CB24
150…240 Silicone 1x SÜEV10-240CU- - - CSA 12-x IEC, GOST, GB/DL
xxxx-CB24
nkt cables 25…120 Silicone 1x SÜEV10-120CU- 1x SÜEV10-120CU- - CSA 12-x IEC, GOST, GB/DL
xxxx-CB24 xxxx-CC24
150…240 Silicone 1x SÜEV10-240CU- 1x SÜEV10-240CU- - CSA 12-x IEC, GOST, GB/DL
xxxx-CB24 xxxx-CC24
1
2

Description
Thermoplastic-insulated cables ≤ 12 kV (according to IEC 60502-2 and VDE 0276-620)
Cable type Cable sealing end Remark
Make Type Cross-

section
[mm2]
1-core cable, PE- and Nexans Euromold 430TB/G 35...300 EPDM with conductive layer
XLPE-insulated 480TB/G 35...300 EPDM with conductive layer
N2YSY (Cu) and N2XSY 484TB/G 50...630 EPDM with conductive layer
(Cu) 489TB/G 800...1200 EPDM with conductive layer
or nkt cables CB 12-630 25...300 Silicone with conductive layer (optionally with metal housing)
NA2YSY (Al) and CB 17.5-630 25...500 Silicone with conductive layer
NA2XSY (Al)
CB 24-1250-2 185...500 Silicone with conductive layer
CB 36-630(1250) 400...630 Silicone with conductive layer
Südkabel SET 12 50...300 Silicone with conductive layer (optionally with metal housing)
SEHDT 13 400...500 Silicone with conductive layer (optionally with metal housing)
Tyco Electronics RSTI-58xx 25...300 Silicone with conductive layer, with capacitive measuring point
Raychem RSTI-395x 400...800 Silicone with conductive layer, with capacitive measuring point
3M 93-EE 705-6 50...240 Silicone with conductive layer (optionally with metal housing)
93-EE 715-6 300...400 Silicone with conductive layer (optionally with metal housing)
GCA CJB10-630 35...500 Silicone with conductive layer
ABB Kabeldon CSE-A 12630-xx 25...630 EPDM with conductive layer
Cellpack CTS 630A 24 kV 50...400 EPDM with conductive layer, with capacitive measuring point
Ample AQT3-15/630 25...400 EPDM with conductive layer
3-core cable, PE and Nexans Euromold 430TB/G 35...300 EPDM with conductive layer, in combination with distribution kit
XLPE-insulated 480TB/G 35...300 EPDM with conductive layer, in combination with distribution kit
N2YSY (Cu) and N2XSY nkt cables CB 12-630 25...300 Silicone with conductive layer (optionally with metal housing), in
(Cu) combination with distribution kit
or CB 24-1250-2 185...500 Silicone with conductive layer, in combination with distribution
NA2YSY (Al) and kit
NA2XSY (Al) CB 17.5-630 25...500 Silicone with conductive layer, in combination with distribution
kit
Südkabel SET 12 50...300 Silicone with conductive layer (optionally with metal housing), in
combination with distribution kit
SEHDT 13 400...500 Silicone with conductive layer (optionally with metal housing), in
Tyco Electronics RSTI-58xx 25...300 Silicone with conductive layer, with capacitive measuring point,
Raychem in combination with distribution kit RSTI-TRFOx
3M 93-EE 705-6 50...240 Silicone with conductive layer (optionally with metal housing), in
93-EE 715-6 300...400 Silicone with conductive layer (optionally with metal housing), in
GCA CJB10-630 25...500 Silicone with conductive layer, in combination with distribution
kit
ABB Kabeldon CSE-A 12630-xx 25...630 EPDM with conductive layer, in combination with distribution kit
Cellpack CTS 630A 24kV 50...400 EPDM with conductive layer, with capacitive measuring point, in
Ample AQT3-15/630 25...400 EPDM with conductive layer, in combination with distribution kit

Description
Thermoplastic-insulated cables 15/17.5/24 kV (according to IEC 60502-2 and VDE 0276-620)
Make Type Cross-section

[mm2]
1-core cable, PE- and Nexans Euromold K430TB/G 35...300 EPDM with conductive layer
XLPE-insulated K480TB/G 35...300 EPDM with conductive layer
N2YSY (Cu) and N2XSY K484TB/G 35...630 EPDM with conductive layer
(Cu)
K489TB/G 800...1200 EPDM with conductive layer
or
nkt cables CB 24-630 25...300 Silicone with conductive layer (optionally with metal housing)
NA2YSY (Al) and NA2XSY
(Al)
CB 36-630(1250) 400...630 Silicone with conductive layer
Südkabel SET 24 50...300 Silicone with conductive layer (optionally with metal housing)
SEHDT 23 400...500 Silicone with conductive layer (optionally with metal housing)
Tyco Electronics RSTI-58xx 25...300 Silicone with conductive layer, with capacitive measuring
Raychem point
RSTI-595x 400...800 Silicone with conductive layer, with capacitive measuring
point
3M 93-EE 705-6 25...240 Silicone with conductive layer (optionally with metal housing)
93-EE 715-6 300...400 Silicone with conductive layer (optionally with metal housing)
GCA CJB20-630 35...500 Silicone with conductive layer
ABB Kabeldon CSE-A 24630-xx 25...630 EPDM with conductive layer
Cellpack CTS 630A 24kV 25...300 EPDM with conductive layer, with capacitive measuring point
Ample AQT3-24/630 35...500 EPDM with conductive layer
3-core cable, PE and XLPE- Nexans Euromold K430TB/G 35...300 EPDM with conductive layer, in combination with distribution
insulated kit
N2YSY (Cu) and N2XSY K480TB/G 35...300 EPDM with conductive layer, in combination with distribution
(Cu) kit
or nkt cables CB 24-630 25...300 Silicone with conductive layer (optionally with metal housing),
NA2YSY (Al) and NA2XSY in combination with distribution kit
(Al) CB 24-1250-2 185...500 Silicone with conductive layer, in combination with
distribution kit
Südkabel SET 24 50...300 Silicone with conductive layer (optionally with metal housing),
in combination with distribution kit
SEHDT 23 400...500 Silicone with conductive layer (optionally with metal housing),
Tyco Electronics RSTI-58xx 25...300 Silicone with conductive layer, with capacitive measuring
Raychem point, in combination with distribution kit RSTI-TRF0x
3M 93-EE 705-6 25...240 Silicone with conductive layer (optionally with metal housing),
93-EE 715-6 300...400 Silicone with conductive layer (optionally with metal housing),
GCA CJB20-630 35...500 Silicone with conductive layer, in combination with
distribution kit
ABB Kabeldon CSE-A 24630-xx 25...630 EPDM with conductive layer, in combination with distribution
kit
Cellpack CTS 630A 24kV 25...300 EPDM with conductive layer, with capacitive measuring point,
Ample AQT3-24/630 35...500 EPDM with conductive layer, in combination with distribution
kit
Paper-insulated belted cables (non-draining cables) ≤ 12 kV (according to IEC 60055 and VDE 0255)

2
Make Type Cross-section [mm ]
3-core cable, paper-insulated Nexans Euromold 430TB/G 35...300 EPDM with conductive layer, in combination
NKBA (Cu), NKBY (Cu), NKRA with distribution kit MIND
(Cu) and NKFA (Cu) nkt cables CB 24-630 25...240 Silicone with conductive layer (optionally
or with metal housing), in combination with
NAKBA (Al), NAKBY (Al), transition sealing end type SÜEV 10
NAKRA (Al) and NAKFA (Al)

Description
Paper-insulated belted cables (non-draining cables) ≤ 12 kV (according to GOST 18410-73)

2
3-core cable, paper-insulated Nexans Euromold 430TB/G 35...300 EPDM with conductive layer, in combination
ASB and ASBL with distribution kit MIND
nkt cables CB 24-630 25...240 Silicone with conductive layer (optionally
with metal housing), in combination with
transition sealing end type SÜEV 10
Paper-insulated belted cables (mass-impregnated cables) ≤ 12 kV (according to IEC 60055 and VDE 0255)

2
3-core cable, paper-insulated nkt cables CB 24-630 25...240 Silicone with conductive layer (optionally
NKBA (Cu), NKBY (Cu), NKRA with metal housing), in combination with
(Cu) and NKFA (Cu) transition sealing end type SÜEV 10
or
NAKBA (Al), NAKBY (Al),
NAKRA (Al) and NAKFA (Al)
Paper-insulated belted cables (mass-impregnated cables) ≤ 12 kV (according to GOST 18410-73)

2
3-core cable, paper-insulated nkt cables CB 24-630 25...240 Silicone with conductive layer (optionally
ASB and ASBL with metal housing), in combination with
transition sealing end type SÜEV 10
Commercially available bar systems
Bar type Bar connection Remark
Make Type Conductor material Maximum rated current

Solid-insulated MGC Moser Glaser Duresca DE Copper 1250 A / 2500 A Outer sheath made of polyamide
busbars (polyamide tube)
Duresca DG Copper 1250 A / 2500 A Outer sheath made of CrNi steel or
aluminum (metal sheath)
Preissinger ISOBUS MB Copper 1250 A / 2500 A Outer sheath made of epoxy resin
(with heat shrinkable tube, if
required)
Ritz SIS Copper 1250 A / 2500 A Outer sheath made of epoxy resin
(with heat shrinkable tube, if
required)
Surge-proof caps
Make Type Size Rated voltage Remark

3M SP 33 Outside cone type "C" 12 kV Silicone with semi-conductive layer
SP 33 Outside cone type "C" 24 kV
Nexans Euromold 400DR-B Outside cone type "C" 12 kV EPDM with semi-conductive layer
K400DR-B Outside cone type "C" 24 kV
nkt cables CBC 40,5-630 Outside cone type "C" 12 kV Silicone with semi-conductive layer
CBC 40,5-630 Outside cone type "C" 24 kV
Südkabel SP 33 Outside cone type "C" 12 kV Silicone with semi-conductive layer
SP 33 Outside cone type "C" 24 kV
Cellpack CIK Outside cone type "C" 12 kV EPDM with semi-conductive layer
CIK Outside cone type "C" 24 kV
Ample AJM-15/630 Outside cone type "C" 12 kV EPDM with semi-conductive layer
AJM-24/630 Outside cone type "C" 24 kV

Description
INFORMATION
For 3-, 4-, 6- or 8-fold cable connection:
➭ Observe the manufacturer’s specifications to the rated normal current of the cable plugs
used.
Cable T-plug connection • Connection of cable T-plugs suitable for bushings with outside cone as interface type C
according to EN 50181
• Connection cross-sections up to 800 mm 2
Surge arresters • Pluggable on cable T-plug

• Surge arresters recommended if, at the same time,
- the cable system is directly connected to the overhead line,
- the protection zone of the surge arrester at the end tower of the overhead line does not
cover the switchgear
Surge limiters • Pluggable on cable T-plug (Nexans Euromold, nkt cables, Tyco Electronics Raychem)
• Nexans Euromold
- Use of the cable T-plug 300PB-630A-U-BEGRENZ for connection of the surge limiter
• nkt cables
- Use of the cable T-plug CC 12-630, CC 17,5-630 or CC 24-630 in combination with the
assembly kit 26 500 33 for connection of the surge limiter
• Tyco Electronics Raychem
- Use of the cable T-plug SMOE 63862 for connection of the surge limiter
• Surge limiters recommended when motors with small starting currents (<600 A) are
connected
9.11 Ready-for-service indicator
Fig. 26: Ready-for-service indicator on the front cover
Features • Self-monitoring, easy to read

• Independent of temperature and external pressure variations
• Independent of the site altitude
• Only responds to changes in gas density
• Option: Signaling switch 1°changeover contact for remote electrical indication
Mode of operation
① Switchgear vessel (filled with SF 6 gas
② Measurement box
③ Magnetic coupling
④ Red indication: not ready for service
⑤ Green indication: ready for service
Fig. 27: Principle of gas monitoring with ready-for-

service indicator
For the ready-for-service indicator, a gas-tight measurement box is installed inside the
switchgear vessel.

Description
A coupling magnet, which is fitted to the bottom end of the measurement box, transmits its
position to an armature outside the switchgear vessel through the non-magnetizable
switchgear vessel (magnetic coupling). This armature moves the ready-for-service indicator at
the operating front of the panel.
While changes in the gas density during the loss of gas, which are decisive for the dielectric
strength, are displayed, changes in the relative gas pressure resulting from temperature and
external pressure variations are not. The gas in the measurement box has the same
temperature as that in the switchgear vessel.
The temperature effect is compensated via the same pressure change in both gas volumes.
9.12 Interlocks
• The three-position switch is equipped with a mechanical interlock. This interlock prevents
the circuit-breaker from being closed while the three-position switch is being operated.
Furthermore the mechanical interlock prevents the three-position switch from being
operated while the circuit-breaker is closed.
• The switching gate prevents switching straight from CLOSED to READY-TO-EARTH or from
READY-TO-EARTH to CLOSED, as the operating lever must be replaced and re-inserted in the
OPEN position.
• The control gate of the switching gate of the three-position switch can be padlocked in all
three switch positions. Control gate lever on the left: the three-position (switch-
)disconnector can be operated, in the center: switching operations are not possible, on the
right: ready-to-earth/earthing is possible.
• Interlocking between feeder locking device and three-position disconnector (circuit-breaker

only lockable in earthed position)
• Interlocking between feeder locking device, three-position disconnector and cable
compartment cover (circuit-breaker only lockable in earthed position, cable compartment
cover only removable in earthed position)
• To do this, lift the interlocking lever ① and remove the cable compartment cover ② .
INFORMATION
To avoid mixing up, the cable compartment covers of panels with a width of 600 mm are
marked with different holes.
Fig. 28: Coding of cable compartment cover for 600 mm panel without fuses (view from
above)

Description
Fig. 29: Coding of cable compartment cover for 600 mm panel with fuses (view from above)
9.13 Voltage detecting systems

For voltage detection according to IEC 61243-5 and VDE 0682 Part 415 with the following
voltage detecting systems:
• Plug-in LRM voltage indicator
• Integrated voltage indicators:
- VOIS
- CAPDIS
- WEGA
① Integrated voltage indicator

② Plug-in LRM voltage indicator
Fig. 30: Voltage detecting system via capacitive voltage

divider (principle)
• -C1: Capacitance integrated into bushing

• -C2: Capacitance of the connection leads and the voltage indicator to earth
• ULE = UN/ √ 3 during rated operation in the three-phase system
• U2 = U A = Voltage at the interface (plug-in sockets) of the plug-in voltage indicator or the
test socket of the integrated voltage indicator
9.14 Accessories
Standard accessories The standard accessories are located in the service flap in the switchgear termination.
CAUTION
Risk of injury when closing the service flap
Fingers can be trapped between service flap and switchgear front.
➭ Hold service flap at the provided handle when closing it, and close it in a controlled
manner.
NOTICE
Service flap slamming closed
➭ Hold service flap at the provided handle, and close it in a controlled manner.
• The label "Service flap equipment" shows the arrangement of the accessories inside the
service flap.

Description
① Torx screwdriver
② Double-bit key (diameter 5 mm)
③ Adapter for emergency operation
④ Operating lever (DISCONNECTING function)
⑤ Installation and operating instructions
⑥ Hand crank
⑦ Operating lever (EARTHING/READY-TO-EARTH
function)
⑧ Double-bit key (diameter 3 mm)
⑨ Adhesive label
Fig. 31: Equipment of service flap with standard accessories
• Installation and operating instructions

• One operating lever for DISCONNECTING function with black ball handles
• One operating lever for EARTHING/READY-TO-EARTH function with red ball handles
Operating levers for the three-position disconnector, only for switchgear with panel widths of 600 mm
(spring-operated mechanism, spring-operated/stored-energy mechanism)
Fig. 32: Operating lever for Fig. 33: Operating lever for EARTHING/
DISCONNECTING function (black READY-TO-EARTH function (red
ball handles) ball handles)
Operating levers for the three-position disconnector, for switchgear with panel widths of 600 and
900 mm (spring-operated mechanism, spring-operated/stored-energy mechanism, slow motion
mechanism)
Fig. 34: Operating lever for DISCONNECTING Fig. 35: Operating lever for EARTHING/
function (black ball handles) READY-TO-EARTH function (red
ball handles)
• Hand crank for charging the circuit-breaker closing spring

Description
• Adapter for emergency operation (to be used only with motor-operated slow motion
mechanisms)
• Double-bit key with a diameter of 3 mm (door of low-voltage compartment)
• Double-bit key with a diameter of 5 mm (voltage transformer disconnector and door of low-
voltage compartment)
• Torx screwdriver T25 to open the cable compartment cover
Other accessories According to the order documents / purchase order (selection):

• Surge arresters
• Surge limiters
• Cable plugs / adapter systems
• Cable plugs
• HV HRC fuse-links
• Test fuses for mechanical simulation of the striker of HV HRC fuse-links in transformer
feeders, with extension tube (for slide lengths 292 mm or 442 mm)
• LRM voltage indicators

• Units to check the capacitive interface and the voltage indicators
• Unit to test the plug-in voltage indicators
• Phase comparison test units
• Holder for operating tools such as hand crank, double-bit key, operating lever

Description
① Holder for operating tools

② Handle of the cable compartment cover

Description
10 Technical data
10.1 Complete switchgear
General electrical data
Rated voltage kV 7.2 12 15 17.5 24

Rated short-duration power-frequency withstand
voltage
- phase-to-phase, phase-to-earth, open contact kV 20 281 36 38 50
gap
- across the isolating distance kV 23 321 39 45 60
Rated lightning impulse withstand voltage
- phase-to-phase, phase-to-earth, open contact kV 60 751 95 95 125
gap
- across the isolating distance kV 70 851 110 110 145
Rated frequency Hz 50/60
Rated short-circuit breaking current kA 31.5 25
Rated short-circuit making current kA 63/80
Rated peak withstand current kA 63/80
Rated short-time withstand current kA max. 31.5 (3 s) max. 25 (3 s)
Rated normal current of busbar, max. A 1250/1600/2000/2500
Rated normal current for incoming and outgoing A 630/1000/1250/2000/2500 630/1000/1250/2000
feeders
Rated normal current for switch-disconnector panel, A 50 ... 250
max. (depending on fuse-link)
Rated normal current
- Vacuum contactor panel without fuses A 450
- Vacuum contactor panel with fuses A 4502
Ring-main panel A 630
Temperature range oC -5/-253 ... +55
1
Higher rated short-duration power-frequency withstand voltage available with:- 42/95 kV for
phase-to-phase, phase-to-earth, open contact gap- 48/110 kV across isolating distance
2
Depending on HV HRC fuse-link. Observe the let-through current of the HV HRC fuse.
3
Option
Test voltages for busbar voltage transformers at 50 Hz

The busbar voltage transformers can be tested together with the switchgear at 80% of the
rated short-duration power-frequency voltage.
Primary voltage [kV] Standard Rated short-duration power- 80% permissible test
frequency withstand voltage value [kV]
[kV]
up to 3.6 IEC 10 8.0
up to 7.2 IEC 20 16.0
GB 23 18.4
GOST 32 25.6
up to 12 IEC 28 22.4
GB 42 33.6
GOST 42 33.6
up to 17.5 IEC 38 30.4
up to 24 IEC 50 40.0
High-voltage test equipment

The following table shows the power consumption per panel for dimensioning the high-
voltage test equipment. The test voltage is supplied through a feeder panel of NXPLUS C.
Further panels to be tested are switched off during the test.

Description
Test voltage [kV] Current consumption of the Current consumption of further

incoming panel [mA] panels (busbar) [mA]
50 10 5
Power losses per panel

Rated normal Rated voltage [kV]
current [A]
7,2 12 15 17.5 24
400 70 W
630 160 W
800 250 W
1000 400 W
1250 600 W
2000 1100 W
2300 1100 W - -
2500 1300 W - -
10.2 Classification of NXPLUS C according to IEC 62271-200
Design and construction

Partition class PM (metallic partition)
Loss of service continuity Panels with HV HRC fuses LSC 2
category Panels without HV HRC fuses LSC 2
Accessibility to compartments Busbar compartment Tool-based
(enclosure) Switching-device compartment Non-accessible
Low-voltage compartment Tool-based
Cable compartment without HV HRC fuses Tool-based
with HV HRC fuses Interlock-controlled and
tool-based
Internal arc classification (IAC) according to IEC 62271-200
Room height Type of installation for the IAC class for rated voltage [kV]
panel
7.2 12 15 17.5 24
≥ 2750 mm Wall-standing arrangement IAC A FL 31.5 kA, 1 s IAC A FL 25 kA, 1 s
Free-standing arrangement IAC FLR 31.5 kA, 1 s IAC FLR 25 kA, 1 s
≥ 2400 mm1 Wall-standing arrangement IAC A FL 25 kA, 1 s IAC A FL 25 kA, 1 s
Free-standing arrangement IAC FLR 25 kA, 1 s IAC FLR 25 kA, 1 s
1
With 1250 A busbar and low-voltage compartment with a height of 761 mm
A Type of accessibility: Switchgear in closed electrical service location, access "for authorized
personnel only".
F Front
L Lateral
R Rear (for free-standing arrangement)
31.5 kA, 25 kA Arc test current
1s Test duration

Description
10.3 Standards, specifications, guidelines
Basic prescriptions and NXPLUS C switchgear complies with the following prescriptions and standards:
standards
IEC standard VDE standard EN standard
Switchgear NXPLUS C IEC 62271-1 VDE 0671-1 EN 62271-1
IEC 62271-200 VDE 0671-200 EN 62271-200
IEC 62271-304 - eLC/TS 62271-304
Devices Circuit-breakers IEC 62271-100 VDE 0671-100 EN 62271-100
Vacuum contactors IEC 60470 VDE 0670-501 EN 60470
Disconnectors
IEC 62271-102 VDE 0671-102 EN 62271-102
Earthing switches
Switch-disconnectors IEC 62271-103 VDE 0671-301 EN 62271-103
Switch-fuse combination IEC 62271-105 VDE 0671-105 EN 62271-105
HV HRC fuses IEC 60282 VDE 0670-4 EN 60282
Voltage detecting systems IEC 61243-5 VDE 0682-415 EN 61243-5
Degree of IP code IEC 60529 VDE 0470-1 EN 60529
protection IK code IEC 62262 VDE 0470-100 EN 50102
Insulation IEC 60071 VDE 0111 EN 60071
Instrument - IEC 61869-1 VDE 0414-9-1 EN 61869-1
transformers Current transformers IEC 61869-2 VDE 0414-9-2 EN 61869-2
Voltage transformers IEC 61869-3 VDE 0414-9-3 EN 61869-3
Installation and erection IEC 61936-1 VDE 0101 -
Insulating Specification for new SF6
IEC 60376 VDE 0373-1 EN 60376
gasSF6
Type approval according The vacuum interrupters fitted in the vacuum circuit-breakers are type-approved in
to German X-ray accordance with the X-ray regulations of the Federal Republic of Germany. They conform to
regulations (RöV) the requirements of the X-ray regulations of January 8, 1987 (Federal Law Gazette I 1987,
Page 114) in the new edition of April 30, 2003 (Federal Law Gazette I 2003, No. 17) up to the
value of the rated voltage stipulated in accordance with IEC/DIN VDE.
Electromagnetic The a.m. standards as well as the "EMC Guide for Switchgear"* are applied during design,
compatibility (EMC) manufacture and erection of the switchgear. 1 Installation, connection and maintenance have
to be performed in accordance with the stipulations of the operating instructions. For
operation, the legal stipulations applicable at the place of installation have to be observed
additionally. In this way, the switchgear assemblies of this type series fulfil the basic
protection requirements of the EMC guide.
Protection against solid The panels of NXPLUS C fulfill the following degrees of protection according to IEC 62271-200,
foreign objects, electric IEC 60529 and DIN VDE 0671-200:
shock and water • IP3XD standard for switchgear enclosure of operating front and side walls
• IP31D option for switchgear enclosure of operating front and side walls
• IP54 option for switchgear enclosure of operating front and side walls
• IP65 for parts under high voltage in switchgear panels without HV HRC fuses
Aseismic capacity (option) NXPLUS C switchgear can be upgraded for regions at risk from earthquakes. For upgrading,
earthquake qualification testing has been carried out in accordance with the following
standards:
• IEC 60068-3-3 “Guidance – seismic test methods for equipment”
• IEC 60068-2-57 “Test Ff: Vibration – Time-history method”
• IEC 60068-2-59 “Test Fe: Vibration – Sine-beat method”
• IEEE 693-2005 “Recommended Practice for Seismic Design of Substations”.
1
Dr. Bernd Jäkel, Ansgar Müller, "Medium-Voltage Systems – EMC Guide for Switchgear", Siemens AG
2012

Description
For installation on even and rigid concrete or steel structure (without considering building
influences), the tested ground accelerations meet the following requirements:
• Uniform Building Code 1997 (UBC) – Zone 4
• California Building Code 1998 (CBC) – Zone 4
• IEEE 693-2005 - High required response spectrum (Figure A.1).
Shock and vibration NXPLUS C switchgear can be upgraded to withstand stress caused by shock and vibration. For
safety (option) upgrading, shock and vibration tests have been carried out in accordance with the following
standards:
• ETSI EN 300 019-2-2; T2.3 Public Transportation
• IEC 60068-2-6, Environmental Testing – Part 2-6:Tests – Test Fc: Vibration (sinusoidal)
• IEC 60068-2-64, Environmental Testing – Part 2-64:Tests – Test Fh: Vibration, broad-band,
random and guidance (noise spectrum according to DNV).
10.4 Selection of HV HRC fuse-links
Note to HV HRC fuse-links According to IEC 60282-1 (2009) Clause 6.6, the breaking capacity of HV HRC fuse-links is
tested within the scope of the type test at 87% of their rated voltage.
In three-phase systems with resonance-earthed or isolated neutral, under double earth fault
and other conditions, the full phase-to-phase voltage may be available at the HV HRC fuse-link
during breaking. Depending on the size of the operating voltage of such a system, this applied
voltage may then exceed 87% of the rated voltage.
To be observed during configuration of switching devices and selection of HV HRC fuse-links:
• Use only fuse-links satisfying the stated operating conditions.
• Use only fuse-links whose breaking capacity was tested at least with the maximum system
voltage.
In case of doubt, select a suitable HV HRC fuse-link together with the manufacturer.
The three-position switch-disconnector in the transformer feeder (transformer switch) was
combined with HV HRC fuse-links and tested in accordance with IEC 62271-105.
The following protection tables show recommended HV HRC fuse-links for protection of
transformers, motors and voltage transformers in the metering panel.
Furthermore, the switchgear also permits fuse protection of transformers up to ratings of
2000 kVA. Please contact us for such applications.
The protection tables are valid for:
• Maximum ambient air temperature in the switchgear room of 40°C according to
IEC 62271-1/VDE 0670-1000 considering the influence of the switchgear enclosure
Requirements according to IEC 62271-105
Protection of distribution transformers according to IEC 60787/VDE 0670-402
Rated power of transformer (no overload operation)
The specified SIBA HV HRC fuses are type-tested partial range fuses according to IEC 60282-1.
The dimensions correspond to DIN 43625. The HV HRC fuses have a thermal protection in
form of a temperature-limiting striker tripping operating in case of defective HV HRC fuse-links
or high overload currents.
Please contact us if you want to use HV HRC fuses from other manufacturers.
The selection of HV HRC fuse-links is based on:
• IEC 60282-1
• IEC 62271-105/VDE 0671-105
• IEC 60787/VDE 0670-402
• Recommendations and data sheets of fuse manufacturers
• Permissible power loss in the switchgear enclosure at an ambient air temperature up to
40° C

Description
NOTICE
Use of HV HRC fuse-links with incorrect characteristic
Do not use HV HRC fuse-links with different characteristics for nominally equal rated normal
current.
➭ Use exactly specified HV HRC fuse-links from the protection table.
Fuse protection table for transformer panel NXPLUS C (HV HRC fuse-links make SIBA)
Order number of SIBA extension tube: 34 006 01 (Siemens part number: 02911500)
System operating Transformer HV HRC fuse-link

voltage
Un [kV] Sr [kVA] uk [%] Ir [A] Ir [A] Ur [kV] e [mm] Order No. SIBA Extension tube SIBA
3.3 … 3.6 20 4 3.5 6.3 3 … 7.2 292 30 098 13.6,3 X
10 3 … 7.2 292 30 098 13.10 X
3.3 … 3.6 30 4 5.25 10 3 … 7.2 292 30 098 13.10 X
16 3 … 7.2 292 30 098 13.16 X
3.3 … 3.6 50 4 8.75 16 3 … 7.2 292 30 098 13.16 X
20 3 … 7.2 292 30 098 13.20 X
3.3 … 3.6 75 4 13.1 20 3 … 7.2 292 30 098 13.20 X
25 3 … 7.2 292 30 098 13.25 X
3.3 … 3.6 100 4 17.5 31.5 3 … 7.2 292 30 098 13.31,5 X
40 3 … 7.2 292 30 098 13.40 X
3.3 … 3.6 125 4 21.9 31.5 3 … 7.2 292 30 098 13.31,5 X
40 3 … 7.2 292 30 098 13.40 X
3.3 … 3.6 160 4 28 40 3 … 7.2 292 30 098 13.40 X
50 3 … 7.2 292 30 098 13.50 X
3.3 … 3.6 200 4 35 50 3 … 7.2 292 30 098 13.50 X
63 3 … 7.2 292 30 099 13.63 X
3.3 … 3.6 250 4 43.7 63 3 … 7.2 292 30 099 13.63 X
80 3 … 7.2 292 30 099 13.80 X
3.3 … 3.6 315 4 55.1 80 3 … 7.2 292 30 099 13.80 X
100 3 … 7.2 292 30 099 13,100 X
3.3 … 3.6 400 4 70 100 3 … 7.2 292 30 099 13,100 X
4 … 4.8 20 4 2.9 6.3 3 … 7.2 292 30 098 13.6,3 X
4 … 4.8 30 4 4.4 10 3 … 7.2 292 30 098 13.10 X
4 … 4.8 50 4 7.3 16 3 … 7.2 292 30 098 13.16 X
4 … 4.8 75 4 11 16 3 … 7.2 292 30 098 13.16 X
20 3 … 7.2 292 30 098 13.20 X
4 … 4.8 100 4 14.5 20 3 … 7.2 292 30 098 13.20 X
25 3 … 7.2 292 30 098 13.25 X
4 … 4.8 125 4 18.1 25 3 … 7.2 292 30 098 13.25 X
31.5 3 … 7.2 292 30 098 13.31,5 X
4 … 4.8 160 4 23.1 31.5 3 … 7.2 292 30 098 13.31,5 X
40 3 … 7.2 292 30 098 13.40 X
4 … 4.8 200 4 28.7 40 3 … 7.2 292 30 098 13.40 X
50 3 … 7.2 292 30 098 13.50 X
4 … 4.8 250 4 36.1 50 3 … 7.2 292 30 098 13.50 X
63 3 … 7.2 292 30 099 13.63 X
4 … 4.8 315 4 45.5 63 3 … 7.2 292 30 099 13.63 X
80 3 … 7.2 292 30 099 13.80 X
4 … 4.8 400 4 57.8 80 3 … 7.2 292 30 099 13.80 X
100 3 … 7.2 292 30 099 13,100 X
4 … 4.8 500 4 72.2 100 3 … 7.2 292 30 099 13,100 X
5 … 5.5 20 4 2.3 6.3 3 … 7.2 292 30 098 13.6,3 X
5 … 5.5 30 4 3.4 6.3 3 … 7.2 292 30 098 13.6,3 X
10 3 … 7.2 292 30 098 13.10 X

Description

voltage
5 … 5.5 50 4 5.7 10 3 … 7.2 292 30 098 13.10 X
16 3 … 7.2 292 30 098 13.16 X
5 … 5.5 75 4 8.6 16 3 … 7.2 292 30 098 13.16 X
20 3 … 7.2 292 30 098 13.20 X
5 … 5.5 100 4 11.5 16 3 … 7.2 292 30 098 13.16 X
20 3 … 7.2 292 30 098 13.20 X
5 … 5.5 125 4 14.4 20 3 … 7.2 292 30 098 13.20 X
25 3 … 7.2 292 30 098 13.25 X
5 … 5.5 160 4 18.4 31.5 3 … 7.2 292 30 098 13.31,5 X
40 3 … 7.2 292 30 098 13.40 X
5 … 5.5 200 4 23 40 3 … 7.2 292 30 098 13.40 X
50 3 … 7.2 292 30 098 13.50 X
5 … 5.5 250 4 28.8 40 3 … 7.2 292 30 098 13.40 X
50 3 … 7.2 292 30 098 13.50 X
5 … 5.5 315 4 36.3 50 3 … 7.2 292 30 098 13.50 X
63 3 … 7.2 292 30 099 13.63 X
5 … 5.5 400 4 46.1 63 3 … 7.2 292 30 099 13.63 X
80 3 … 7.2 292 30 099 13.80 X
5 … 5.5 500 4 57.7 80 3 … 7.2 292 30 099 13.80 X
100 3 … 7.2 292 30 099 13,100 X
5 … 5.5 630 4 72.74 100 3 … 7.2 292 30 099 13,100 X
6 … 7.2 20 4 1.9 6.3 6 … 12 292 30 004 13.6,3 X
6.3 3 … 7.2 292 30 098 13.6,3 X
6.3 6 … 12 442 30 101 13.6,3 ---
6 … 7.2 30 4 2.8 6.3 6 … 12 292 30 004 13.6,3 X
6.3 3 … 7.2 292 30 098 13.6,3 X
6.3 6 … 12 442 30 101 13.6,3 ---
6 … 7.2 50 4 4.8 10 3 … 7.2 292 30 098 13.10 X
10 6 … 12 292 30 004 13.10 X
10 6 … 12 442 30 101 13.10 ---
16 3 … 7.2 292 30 098 13.16 X
16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
6 … 7.2 75 4 7.2 16 3 … 7.2 292 30 098 13.16 X
16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
6 … 7.2 100 4 9.6 16 3 … 7.2 292 30 098 13.16 X
16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
20 3 … 7.2 292 30 098 13.20 X
20 6 … 12 292 30 004 13.20 X
20 6 … 12 442 30 101 13.20 ---
6 … 7.2 125 4 12 20 3 … 7.2 292 30 098 13.20 X
20 6 … 12 292 30 004 13.20 X
20 6 … 12 442 30 101 13.20 ---
25 3 … 7.2 292 30 098 13.25 X
25 6 … 12 292 30 004 13.25 X
25 6 … 12 442 30 101 13.25 ---
6 … 7.2 160 4 15.4 31.5 3 … 7.2 292 30 098 13.31,5 X
31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
6 … 7.2 200 4 19.2 31.5 3 … 7.2 292 30 098 13.31,5 X
31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
40 3 … 7.2 292 30 098 13.40 X
40 6 … 12 292 30 004 13.40 X
40 6 … 12 442 30 101 13.40 ---

Description

voltage
6 … 7.2 250 4 24 40 3 … 7.2 292 30 098 13.40 X
40 6 … 12 292 30 004 13.40 X
40 6 … 12 442 30 101 13.40 ---
50 3 … 7.2 292 30 098 13.50 X
50 6 … 12 292 30 004 13.50 X
50 6 … 12 442 30 101 13.50 ---
6 … 7.2 315 4 30.3 50 3 … 7.2 292 30 098 13.50 X
50 6 … 12 292 30 004 13.50 X
50 6 … 12 442 30 101 13.50 ---
63 6 … 12 292 30 012 43.63 X
6 … 7.2 400 4 38.4 63 3 … 7.2 292 30 099 13.63 X
63 6 … 12 292 30 012 13.63 X
63 6 … 12 442 30 102 13.63 ---
63 6 … 12 292 30 012 43.63 X
80 6 … 12 292 30 012 43.80 X
80 6 … 12 442 30 102 43.80 ---
6 … 7.2 500 4 48 80 6 … 12 292 30 012 43.80 X
80 6 … 12 442 30 102 43.80 ---
80 3 … 7.2 292 30 099 13.80 X
80 6 … 12 292 30 012 13.80 X
80 6 … 12 442 30 102 13.80 ---
100 6 … 12 292 30 012 43,100 X
100 6 … 12 442 30 102 43,100 ---
6 … 7.2 630 4 61 100 3 … 7.2 292 30 099 13,100 X
100 6 … 12 292 30 012 13,100 X
100 6 … 12 442 30 102 13,100 ---
100 6 … 12 292 30 012 43,100 X
100 6 … 12 442 30 102 43,100 ---
125 6 … 12 292 30 020 43,125 X
125 6 … 12 442 30 103 43,125 ---
6 … 7.2 800 5…6 77 125 6 … 12 442 30 103 43,125 ---
7.6 … 8.4 20 4 1.5 6.3 6 … 12 292 30 004 13.6,3 X
6.3 6 … 12 442 30 101 13.6,3 ---
7.6 … 8.4 30 4 2.27 5 6 … 12 292 30 004 13.5 X
6.3 6 … 12 292 30 004 13.6,3 X
6.3 6 … 12 442 30 101 13.6,3 ---
7.6 … 8.4 50 4 3.7 10 6 … 12 292 30 004 13.10 X
10 6 … 12 442 30 101 13.10 ---
7.6 … 8.4 75 4 5.7 16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
7.6 … 8.4 100 4 7.6 16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
7.6 … 8.4 125 4 9.5 20 6 … 12 292 30 004 13.20 X
20 6 … 12 442 30 101 13.20 ---
7.6 … 8.4 160 4 12.1 31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
7.6 … 8.4 200 4 15.2 31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
7.6 … 8.4 250 4 19 40 6 … 12 292 30 004 13.40 X
40 6 … 12 442 30 101 13.40 ---
7.6 … 8.4 315 4 23.9 50 6 … 12 292 30 004 13.50 X
50 6 … 12 442 30 101 13.50 ---
7.6 … 8.4 400 4 30.3 63 6 … 12 292 30 012 13.63 X
63 6 … 12 442 30 102 13.63 ---
7.6 … 8.4 500 4 37.9 80 6 … 12 292 30 012 43.80 X
80 6 … 12 442 30 102 43.80 ---
7.6 … 8.4 630 4 47.8 100 6 … 12 292 30 012 43,100 X
100 6 … 12 442 30 102 43,100 ---

Description

voltage
8.9 20 4 1.3 6.3 6 … 12 292 30 004 13.6,3 X
6.3 6 … 12 442 30 101 13.6,3 ---
8.9 30 4 2 5 6 … 12 292 30 004 13.5 X
6.3 6 … 12 292 30 004 13.6,3 X
6.3 6 … 12 442 30 101 13.6,3 ---
8.9 50 4 3.3 10 6 … 12 292 30 004 13.10 X
10 6 … 12 442 30 101 13.10 ---
8.9 75 4 4.9 16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
8.9 100 4 6.5 16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
8.9 125 4 8.1 20 6 … 12 292 30 004 13.20 X
20 6 … 12 442 30 101 13.20 ---
8.9 160 4 10.4 25 6 … 12 292 30 004 13.25 X
25 6 … 12 442 30 101 13.25 ---
8.9 200 4 13 31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
8.9 250 4 16.2 40 6 … 12 292 30 004 13.40 X
40 6 … 12 442 30 101 13.40 ---
8.9 315 4 20.5 50 6 … 12 292 30 004 13.50 X
50 6 … 12 442 30 101 13.50 ---
8.9 400 4 26 63 6 … 12 292 30 012 13.63 X
63 6 … 12 442 30 102 13.63 ---
8.9 500 4 32.5 80 6 … 12 292 30 012 43.80 X
80 6 … 12 442 30 102 43.80 ---
8.9 630 4 41 100 6 … 12 292 30 012 43,100 X
100 6 … 12 442 30 102 43,100 ---
10 … 12 20 4 1.15 4 6 … 12 292 30 004 13.4 X
10 … 12 30 4 1.7 6.3 6 … 12 442 30 101 13.6,3 ---
10 … 12 50 4 2.9 10 6 … 12 292 30 004 13.10 X
10 6 … 12 442 30 101 13.10 ---
10 10 … 17.5 292 30 255 13.10 X
10 10 … 17.5 442 30 231 13.10 ---
10 10 … 24 442 30 006 13.10 ---
10 … 12 75 4 4.3 10 6 … 12 292 30 004 13.10 X
10 6 … 12 442 30 101 13.10 ---
10 10 … 17.5 292 30 255 13.10 X
10 10 … 17.5 442 30 231 13.10 ---
10 10 … 24 442 30 006 13.10 ---
10 … 12 100 4 5.8 16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
16 10 … 17.5 292 30 255 13.16 X
16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
10 … 12 125 4 7.2 16 6 … 12 292 30 004 13.16 X
16 6 … 12 442 30 101 13.16 ---
16 10 … 17.5 292 30 255 13.16 X
16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
10 … 12 160 4 9.3 20 6 … 12 292 30 004 13.20 X
20 6 … 12 442 30 101 13.20 ---
20 10 … 17.5 292 30 221 13.20 X
20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---

Description

voltage
10 … 12 200 4 11.5 25 6 … 12 292 30 004 13.25 X
25 6 … 12 442 30 101 13.25 ---
25 10 … 17.5 292 30 221 13.25 X
25 10 … 17.5 442 30 231 13.25 ---
25 10 … 24 442 30 006 13.25 ---
10 … 12 250 4 14.5 25 6 … 12 292 30 004 13.25 X
25 6 … 12 442 30 101 13.25 ---
25 10 … 17.5 292 30 221 13.25 X
25 10 … 17.5 442 30 231 13.25 ---
25 10 … 24 442 30 006 13.25 ---
31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
31.5 10 … 17.5 292 30 221 13.31,5 X
31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
10 … 12 315 4 18.3 31.5 6 … 12 292 30 004 13.31,5 X
31.5 6 … 12 442 30 101 13.31,5 ---
31.5 10 … 17.5 292 30 221 13.31,5 X
31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
40 6 … 12 292 30 004 13.40 X
40 6 … 12 442 30 101 13.40 ---
40 10 … 17.5 292 30 221 13.40 X
40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---
10 … 12 400 4 23.1 40 6 … 12 292 30 004 13.40 X
40 6 … 12 442 30 101 13.40 ---
40 10 … 17.5 292 30 221 13.40 X
40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---
50 6 … 12 292 30 004 13.50 X
50 6 … 12 442 30 101 13.50 ---
50 10 … 17.5 292 30 221 13.50 X
50 10 … 17.5 442 30 232 13.50 ---
50 10 … 24 442 30 014 13.50 ---
10 … 12 500 4 29 50 6 … 12 292 30 004 13.50 X
50 6 … 12 442 30 101 13.50 ---
50 10 … 17.5 292 30 221 13.50 X
50 10 … 17.5 442 30 232 13.50 ---
50 10 … 24 442 30 014 13.50 ---
63 6 … 12 292 30 012 43.63 X
63 10 … 24 442 30 014 43.63 ---
10 … 12 630 4 36.4 63 6 … 12 292 30 012 13.63 X
63 6 … 12 442 30 102 13.63 ---
63 10 … 17.5 442 30 232 13.63 ---
63 6 … 12 292 30 012 43.63 X
63 10 … 24 442 30 014 43.63 ---
80 6 … 12 292 30 012 43.80 X
80 6 … 12 442 30 102 43.80 ---
80 10 … 24 442 30 014 43.80 ---
10 … 12 800 5…6 46.2 63 6 … 12 292 30 012 13.63 X
63 6 … 12 442 30 102 13.63 ---
80 6 … 12 292 30 012 43.80 X
80 6 … 12 442 30 102 43.80 ---
10 … 12 1000 5…6 58 100 6 … 12 292 30 012 43,100 X
100 6 … 12 442 30 102 43,100 ---
100 10 … 24 442 30 022 43,100 ---

Description

voltage
10 … 12 1250 5…6 72 125 6 … 12 292 30 020 43,125 X
125 6 … 12 442 30 103 43,125 ---
12.4 … 13.4 20 4 0.94 4 10 … 24 442 30 006 13.4 ---
12.4 … 13.4 30 4 1.4 6.3 10 … 24 442 30 006 13.6,3 ---
6.3 10 … 24 442 30 231 13.6,3 ---
12.4 … 13.4 50 4 2.4 10 10 … 17.5 442 30 231 13.10 ---
10 10 … 24 442 30 006 13.10 ---
12.4 … 13.4 75 4 3.5 10 10 … 17.5 442 30 231 13.10 ---
10 10 … 24 442 30 006 13.10 ---
12.4 … 13.4 100 4 4.7 16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
12.4 … 13.4 125 4 5.9 16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
12.4 … 13.4 160 4 7.5 16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
12.4 … 13.4 200 4 9.4 20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---
12.4 … 13.4 250 4 11.7 25 10 … 17.5 442 30 231 13.25 ---
31.5 10 … 17.5 442 30 231 13.31,5 ---
25 10 … 24 442 30 006 13.25 ---
31.5 10 … 24 442 30 006 13.31,5 ---
12.4 … 13.4 315 4 14.7 31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
12.4 … 13.4 400 4 18.7 40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---
12.4 … 13.4 500 4 23.3 50 10 … 17.5 442 30 232 13.50 ---
50 10 … 24 442 30 014 13.50 ---
12.4 … 13.4 630 4 29.4 63 10 … 17.5 442 30 232 13.63 ---
63 10 … 24 442 30 014 13.63 ---
12.4 … 13.4 800 5…6 37.3 80 10 … 24 442 30 014 43.80 ---
13.8 20 4 0.8 3.15 10 … 24 442 30 006 13.3 ---
13.8 30 4 1.25 4 10 … 24 442 30 006 13.4 ---
13.8 50 4 2.1 6.3 10 … 17.5 442 30 231 13.6,3 ---
6.3 10 … 24 442 30 006 13.6,3 ---
13.8 75 4 3.2 6.3 10 … 17.5 442 30 231 13.6,3 ---
10 10 … 17.5 442 30 231 13.10 ---
10 10 … 24 442 30 006 13.10 ---
13.8 100 4 4.2 10 10 … 17.5 442 30 231 13.10 ---
16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
13.8 125 4 5.3 10 10 … 17.5 442 30 231 13.10 ---
16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
13.8 160 4 6.7 16 10 … 17.5 442 30 231 13.16 ---
13.8 200 4 8.4 16 10 … 17.5 442 30 231 13.16 ---
20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---
13.8 250 4 10.5 20 10 … 17.5 442 30 231 13.20 ---
25 10 … 17.5 442 30 231 13.25 ---
25 10 … 24 442 30 006 13.25 ---
13.8 315 4 13.2 25 10 … 17.5 442 30 231 13.25 ---
31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
13.8 400 4 16.8 31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
13.8 500 4 21 40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---

Description

voltage
13.8 630 4 26.4 50 10 … 17.5 442 30 232 13.50 ---
50 10 … 24 442 30 014 13.50 ---
13.8 800 5…6 33.5 63 10 … 17.5 442 30 232 13.63 ---
63 10 … 24 442 30 014 13.63 ---
63 10 … 24 442 30 014 43.63 ---
13.8 1000 5…6 41.9 80 10 … 24 442 30 014 43.80 ---
13.8 1250 5…6 52.3 100 10 … 24 442 30 022 43,100 ---
14.4 20 4 0.8 3.15 10 … 24 442 30 006 13.3 ---
14.4 30 4 1.2 3.15 10 … 24 442 30 006 13.3 ---
14.4 50 4 2 6.3 10 … 17.5 442 30 231 13.6,3 ---
6.3 10 … 24 442 30 006 13.6,3 ---
14.4 75 4 3 6.3 10 … 17.5 442 30 231 13.6,3 ---
6.3 10 … 24 442 30 006 13.6,3 ---
14.4 100 4 4 10 10 … 17.5 442 30 231 13.10 ---
16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
14.4 125 4 5 10 10 … 17.5 442 30 231 13.10 ---
16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
14.4 160 4 6.5 16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
14.4 200 4 8 16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---
14.4 250 4 10 20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---
25 10 … 17.5 442 30 231 13.25 ---
25 10 … 24 442 30 006 13.25 ---
14.4 315 4 12.6 20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---
25 10 … 17.5 442 30 231 13.25 ---
25 10 … 24 442 30 006 13.25 ---
14.4 400 4 16.1 31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
14.4 500 4 20.1 40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---
14.4 630 4 25.3 50 10 … 17.5 442 30 232 13.50 ---
50 10 … 24 442 30 014 13.50 ---
14.4 800 5…6 32.1 63 10 … 24 442 30 014 43.63 ---
14.4 1000 5…6 40.1 80 10 … 24 442 30 014 43.80 ---
14.4 1250 5…6 50.2 100 10 … 24 442 30 022 43,100 ---
15 … 17.5 20 4 0.77 3.15 10 … 24 442 30 006 13.3 ---
15 … 17.5 30 4 1.15 3.15 10 … 24 442 30 006 13.3 ---
15 … 17.5 50 4 1.9 6.3 10 … 17.5 442 30 231 13.6,3 ---
6.3 10 … 24 442 30 006 13.6,3 ---
15 … 17.5 75 4 2.9 6.3 10 … 17.5 442 30 231 13.6,3 ---
15 … 17.5 100 4 3.9 10 10 … 17.5 442 30 231 13.10 ---
15 … 17.5 125 4 4.8 16 10 … 17.5 442 30 231 13.16 ---
16 10 … 24 442 30 006 13.16 ---
15 … 17.5 160 4 6.2 16 10 … 17.5 442 30 231 13.16 ---
15 … 17.5 200 4 7.7 20 10 … 17.5 442 30 231 13.20 ---
20 10 … 24 442 30 006 13.20 ---
15 … 17.5 250 4 9.7 25 10 … 17.5 442 30 231 13.25 ---
25 10 … 24 442 30 006 13.25 ---
15 … 17.5 315 4 12.2 31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---

Description

voltage
15 … 17.5 400 4 15.5 31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
15 … 17.5 500 4 19.3 31.5 10 … 17.5 442 30 231 13.31,5 ---
31.5 10 … 24 442 30 006 13.31,5 ---
40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---
15 … 17.5 630 4 24.3 40 10 … 17.5 442 30 231 13.40 ---
40 10 … 24 442 30 006 13.40 ---
50 10 … 17.5 442 30 232 13.50 ---
50 10 … 24 442 30 014 13.50 ---
63 10 … 24 442 30 014 43.63 ---
15 … 17.5 800 5…6 30.9 63 10 … 24 442 30 014 43.63 ---
15 … 17.5 1000 5…6 38.5 63 10 … 24 442 30 014 43.63 ---
80 10 … 24 442 30 014 43.80 ---
15 … 17.5 1250 5…6 48.2 100 10 … 24 442 30 022 43,100 ---
18 … 19 20 4 0.64 3.15 10 … 24 442 30 006 13.3 ---
18 … 19 30 4 0.96 3.15 10 … 24 442 30 006 13.3 ---
18 … 19 50 4 1.6 6.3 10 … 24 442 30 006 13.6,3 ---
18 … 19 75 4 2.4 6.3 10 … 24 442 30 006 13.6,3 ---
18 … 19 100 4 3.2 10 10 … 24 442 30 006 13.10 ---
18 … 19 125 4 4 10 10 … 24 442 30 006 13.10 ---
18 … 19 160 4 5.1 16 10 … 24 442 30 006 13.16 ---
18 … 19 200 4 6.4 16 10 … 24 442 30 006 13.16 ---
18 … 19 250 4 8.1 20 10 … 24 442 30 006 13.20 ---
18 … 19 315 4 10.1 25 10 … 24 442 30 006 13.25 ---
18 … 19 400 4 12.9 31.5 10 … 24 442 30 006 13.31,5 ---
18 … 19 500 4 16.1 31.5 10 … 24 442 30 006 13.31,5 ---
40 10 … 24 442 30 006 13.40 ---
18 … 19 630 4 20.2 40 10 … 24 442 30 006 13.40 ---
50 10 … 24 442 30 006 13.50 ---
63 10 … 24 442 30 014 43.63 ---
18 … 19 800 4…5 25.7 50 10 … 24 442 30 014 13.50 ---
63 10 … 24 442 30 014 43.63 ---
18 … 19 1000 5…6 32.1 63 10 … 24 442 30 014 43.63 ---
18 … 19 1250 5…6 40.1 80 10 … 24 442 30 014 43.80 ---
20 … 23 20 4 0.57 3.15 10 … 24 442 30 006 13.3 ---
20 … 23 30 4 0.86 3.15 10 … 24 442 30 006 13.3 ---
20 … 23 50 4 1.5 6.3 10 … 24 442 30 006 13.6,3 ---
20 … 23 75 4 2.2 6.3 10 … 24 442 30 006 13.6,3 ---
20 … 23 100 4 2.9 6.3 10 … 24 442 30 006 13.6,3 ---
20 … 23 125 4 3.6 10 10 … 24 442 30 006 13.10 ---
20 … 23 160 4 4.7 10 10 … 24 442 30 006 13.10 ---
20 … 23 200 4 5.8 16 10 … 24 442 30 006 13.16 ---
20 … 23 250 4 7.3 16 10 … 24 442 30 006 13.16 ---
20 … 23 315 4 9.2 16 10 … 24 442 30 006 13.16 ---
20 10 … 24 442 30 006 13.20 ---
20 … 23 400 4 11.6 20 10 … 24 442 30 006 13.20 ---
25 10 … 24 442 30 006 13.25 ---
20 … 23 500 4 14.5 25 10 … 24 442 30 006 13.25 ---
31.5 10 … 24 442 30 006 13.31,5 ---
20 … 23 630 4 18.2 31.5 10 … 24 442 30 006 13.31,5 ---
40 10 … 24 442 30 006 13.40 ---
20 … 23 800 5…6 23.1 31.5 10 … 24 442 30 006 13.31,5 ---
20 … 23 1000 5…6 29 50 10 … 24 442 30 014 13.50 ---
20 … 23 1250 5…6 36 50 10 … 24 442 30 014 13.50 ---
63 10 … 24 442 30 014 43.63 ---

Description

voltage
20 … 23 1600 5…6 46.5 80 10 … 24 442 30 014 43.80 ---
100 10 … 24 442 30 022 43,100 ---
20 … 23 2000 5…6 57.8 100 10 … 24 442 30 022 43,100 ---
Un System operating voltage

Sr Rated power of transformer
uk Relative impedance voltage of transformer
Ir Rated current of transformer
Ir Rated current of fuse-link
Ur Operating voltage / rated voltage of fuse-link
e Dimension of fuse-link
10.5 Motor protection table (with HV HRC fuses make SIBA)
Number of Maximum permissible motor starting current in A at rated normal current

starts per of HV HRC fuse
hour
40 A 50 A 63 A 80 A 100 A 125 A 160 A 200 A 224 A 250 A
3.3 - 7.2 kV Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
>7.2 - 12 kV Yes Yes Yes Yes Yes Yes Yes Yes No No
>12 - 23 kV Yes Yes Yes Yes Yes No No No No No
HV motors with 2 95 115 135 160 210 415 560 765 860 960
starting times up to 5 4 85 105 120 145 190 370 500 705 840 960
s 8 75 95 110 130 170 340 455 640 760 960
16 70 85 95 115 150 300 405 575 680 925
32 63 75 85 105 140 270 370 520 615 840
HV motors with 2 90 105 120 145 190 335 445 625 730 960
starting times up to 4 80 95 110 130 170 300 400 560 655 890
15 s 8 70 85 100 120 155 270 360 510 595 805
16 65 75 90 105 140 240 325 455 535 720
32 60 70 80 95 125 220 290 410 485 655
HV motors with 2 85 100 115 140 185 300 390 555 645 865
starting times up to 4 75 90 105 125 165 265 350 500 575 780
30 s 8 70 80 95 115 150 245 320 450 525 705
16 60 75 85 100 135 210 285 405 470 630
32 55 65 75 90 120 190 260 365 425 570

Description
Fuse protection table for vacuum contactor (with HV HRC fuse-links make SIBA)
Motor HV HRC fuse-link
Operating voltage Rated current Reference Maximum permissible Order No. SIBA Order No. of SIBA Part number of
dimension normal current extension tube Siemens
extension tube
U [kV] Ir [A] e [mm] I [A]
3.3…7.2 40 292 30 30 098 13.40 34 006 01 02911500
50 442 38 30 108 53.50 --- ---
63 442 47 30 108 53.63 --- ---
80 442 60 30 108 53.80 --- ---
100 442 75 30 108 53,100 --- ---
125 442 85 30 109 53,125 --- ---
160 442 109 30 109 53,160 --- ---
200 442 130 30 110 54,200 --- ---
224 442 137 30 110 54,224 --- ---
250 442 157 30 110 54,250 --- ---
>7.2…12 40 442 29 30 101 13.40 --- ---
50 442 36 30 101 53.50 --- ---
63 442 45 30 101 53.63 --- ---
80 442 47 30 102 53.80 --- ---
100 442 59 30 102 53,100 --- ---
125 442 74 30 102 53,125 --- ---
160 442 90 30 103 53,160 --- ---
200 442 105 30 103 54,200 --- ---
12 125 442 78 30 469 13,125 --- ---
>12…23 40 442 23 30 006 13.40 --- ---
50 442 29 30 014 13.50 --- ---
63 442 36 30 014 43.63 --- ---
80 442 46 30 014 43.80 --- ---
100 442 54 30 022 43,100 --- ---
10.6 Fuse protection table for metering panel (with HV HRC fuse-links make SIBA)
Voltage HV HRC fuse-link

transformer
Operating voltage Rated current Reference Order No. SIBA Order No. of SIBA Part number of
dimension extension tube Siemens
extension tube
U [kV] Ir [A] e [mm]
3.3 - 5.5 6.3 292 30 098 13.6,3 34 006 01 02911500
6.0 - 7.2 0.5 292 30 004 11.0,5 34 006 01 02911500
2.0 292 30 004 13.2 34 006 01 02911500
4.0 292 30 004 13.4 34 006 01 02911500
6.3 292 30 098 13.6,3 34 006 01 02911500
> 7.2 - 12 0.5 292 30 004 13.0,5 34 006 01 02911500
2.0 292 30 004 13.2 34 006 01 02911500
4.0 292 30 004 13.4 34 006 01 02911500
6.3 442 30 101 13.6,3 --- ---
> 12 - 23 0.5 442 30 006 11.0,5 --- ---
2.0 442 30 006 13.2 --- ---
4.0 442 30 006 13.4 --- ---
6.3 442 30 006 13.6,3 --- ---

Description
10.7 Rating plates
Fig. 36: Rating plate on the inside of the low- Fig. 37: Rating plate at the switchgear
voltage compartment vessel
① Switchgear type ⑤ Number of operating cycles

② Serial number ⑥ Year of manufacture
③ Panel number ⑦ Technical data
④ Internal arc classification
IAC classification The data ④ describes the internal arc classification of the panel according to IEC 62271-200.
The data describes the areas classified for the corresponding panel (see page 59,
"Classification of NXPLUS C according to IEC 62271-200").
10.8 Vacuum circuit-breaker
Operating cycles 3AH55

Rated current A ≥ 1000/1250/2000/2500 ≥ 1000/1250/2000
Rated short-time withstand kA 31.5 25
current
Rated normal current Operating 10000
cycles
Short-circuit breaking current Operating 50
cycles
Fig. 38: Permissible number of operating cycles n as a function of the breaking current I a
(r.m.s. value) in kA

Description
Operating cycles 3AH25
Rated voltage kV 7.2 12 15

Rated current A ≥ 1000/1250
Rated short-time withstand kA 31.5
current
Rated normal current Operating cycles 30,000
Short-circuit breaking current Operating cycles 50
Fig. 39: Permissible number of operating cycles n as a function of the breaking current I a
(r.m.s. value) in kA
Rated operating sequences:

Rapid transfer (U): O-t-CO-t'-CO (t = 0.3 s, t'= 3 min)
Auto-reclosing (K): O-t-CO-t'-CO (t= 0.3 s, t'= 3 min)
Auto-reclosing (K): O-t-CO-t'-CO (t= 0.3 s, t'= 15 s)
O = OPEN operation
C = CLOSE operation
CO = CLOSE operation with subsequent OPEN operation at the internal close-open time of the vacuum circuit-
breaker
Operating times
Operating times Component Item designation Duration Unit
3AH55 3AH25
Closing time 75 75 ms
Charging time <15 <15 s
Opening time Shunt release (-Y1) <65 <65 ms
Additional release 3AX (-Y2), (-Y4), (-Y6), (-Y7) <50 <50 ms
11
Arcing time <15 <15 ms
Break time Shunt release (-Y1) <80 <80 ms
11
Dead time 300 300 ms
Close-open contact time Shunt release (-Y1) <75 <80 ms
11
Minimum command duration
CLOSE Closing solenoid (-Y9) 45 45 ms
OPEN Shunt release (-Y1) 40 40 ms
OPEN Additional release 3AX (-Y2), (-Y4), (-Y6), (-Y7) 20 20 ms
11
Shortest impulse duration of the c.b. tripping signal 10 10 ms

Description
Closing time The interval of time between the initiation (command) of the closing operation and the
instant when the contacts touch in all poles.
Opening time The interval of time between the initiation (command) of the opening operation and the
instant when the contacts separate in all poles.
Arcing time The interval of time from the first initiation of an arc and the instant of final arc extinction in
all poles.
Break time The interval of time between the initiation (command) of the opening operation and the
instant of final arc extinction in the last-pole-to-clear (=opening time and arcing time).
Close-open contact time The interval of time - in a make-break operating cycle - between the instant when the contacts
touch in the first pole in the closing process, and the instant when the contacts separate in all
poles in the subsequent opening process.
Motor operating The operating mechanisms of the 3AH55 and 3AH25 circuit-breakers are suitable for auto-
mechanism reclosing. For DC operation, the maximum power consumption is approx. 600 W. For AC
operation, the maximum power consumption is approx. 750 VA
The rated current of the line protection motor operating mechanism is shown in the following
table.
Fuse protection table: Line protection of motor operating mechanism for vacuum
circuit-breaker
Rated voltage of Operating voltage1 Power consumption Rated current of Normal current Smallest possible rated
operating mechanism of motor operating current of the
110% 80% mechanism miniature circuit-
breaker
Ua [V] Umax [V] Umin [V] P [W] S [VA] Ia_A [A] Imax [A] Imin [A] Ia_S [A]
DC 24 26 19 600 – 25.0 31.3 22.7 16
30 33 24 600 – 20.0 25.0 18.2 16
32 35 26 600 – 18.8 23.4 17.0 16
48 53 38 600 – 12.5 15.6 11.4 10
60 66 48 600 – 10.0 12.5 9.1 8
110 121 88 600 – 5.5 6.8 5.0 4
120 132 96 600 – 5.0 6.3 4.5 4
125 138 100 600 – 4.8 6.0 4.4 4
127 140 102 600 – 4.7 5.9 4.3 4
220 242 176 600 – 2.7 3.4 2.5 2
240 264 192 600 – 2.5 3.1 2.3 2
AC 100 110 80 – 750 7.5 9.4 6.8 6
110 121 88 – 750 6.8 8.5 6.2 4
120 132 96 – 750 6.3 7.8 5.7 4
125 138 100 – 750 6.0 7.5 5.5 4
230 253 184 – 750 3.3 4.1 3.0 2
240 264 192 – 750 3.1 3.9 2.8 2
1
The operating voltage may deviate from the rated voltage specified in the table by –20% to +10%.

Description
Breaking capacity of auxiliary switch 3SV92:
Breaking capacity Operating voltage [V] Normal current [A]

AC 40 to 60 Hz up to 240 10
DC 24 10
30 10
32 10
48 9
60 7
110 4
125 4
127 4
220 2
240 2
Time constant of the auxiliary circuit: t = L/R = 20 ms
Closing solenoid (-Y9) The closing solenoid 3AY1510 closes the circuit-breaker. After completion of a closing
operation, the closing solenoid is de-energized internally. It is available for AC or DC voltage.
Power consumption: 140 W or 140 VA.
Shunt releases Shunt releases are used for automatic or deliberate tripping of circuit-breakers. They are
designed for connection to external voltage (DC or AC voltage). They can also be connected to
a voltage transformer for deliberate tripping.
Shunt releases based on two different principles are used:
• The shunt release (-Y1) 3AY1510 is used as standard in the basic circuit-breaker version.
With this design, the circuit-breaker is opened electrically. Power consumption: 140 W or
140 VA.
• The shunt release (-Y2) 3AX1101 with energy store is fitted if more than one shunt release
is required. With this design, the electrical opening command is transferred magnetically
and thus, the circuit-breaker is opened. Power consumption: 70 W or 50 VA.
Undervoltage release Untervoltage releases (-Y7) 3AX1103 are tripped automatically through an electromagnet or
deliberately. The deliberate tripping of the undervoltage release generally takes place via an
NC contact in the tripping circuit or via an NO contact by short-circuiting the magnet coil. With
this type of tripping, the short-circuit current is limited by the built-in resistors. Power
consumption: 20 W or 20 VA.
Circuit-breaker tripping When the circuit-breaker is tripped by a release (e.g. by protection tripping) there is a signal
signal through the NO contact -S6. If the circuit-breaker is tripped deliberately with the mechanical
pushbutton, this signal is suppressed by the NC contact -S7.
Varistor module
NOTICE
Overvoltages in inductive circuits
Electrical control devices can be damaged by switching overvoltages.
➭ Do not switch off inductive consumers in DC circuits.
The inductances of the circuit-breaker operating mechanism and the circuit-breaker control
system (motor, closing solenoid, shunt release and auxiliary contactor) are equipped with the
varistor module 3AX1526 for DC operation. The module limits the overvoltage to approx. 500
V and is available for rated operating voltages from 60 V (DC) up to 220 V (DC). It contains two
separate varistor circuits.

Description
10.9 Three-position disconnector for circuit-breaker, disconnector and bus

sectionalizer panels ≥ 1000 A

Rated current A ≥ 1000/1250/2000/2500 ≥ 1000/1250/2000
Rated short-time withstand kA (3 s) 31.5 25
current
Rated peak withstand current kA 80 kA 63 kA
10.10 Three-position switch-disconnector for switch-disconnector panels, ring-

main panels and circuit-breaker panels up to 630 A, vacuum contactor panel
and metering panel
Rated voltage Ur kV 7.2 12 15 17.5 24

Rated insulation level Rated short-duration power-frequency Ud kV 20 28 35 38 50
withstand voltage
Rated lightning impulse withstand voltage Uw kV 60 75 95 95 125
Rated frequency fr Hz 50/60 50/60 50/60 50/60 50/60
Rated normal current Panels without HV HRC fuses Ir A 630 630 630 630 630
Transformer feeders1 Ir A 200 200 200 200 200
Rated short-time withstand Panels without HV HRC fuses tk = 1 s tk up to kA 20/25 20/25 20/25 20/25 20/-
current tk = 3 s tk kA 20/- 20/- 20/- 20/- 20/-
Panels with HV HRC fuses tk = 1 s tk up to kA 31.5 31.5 31.5 25 25
tk = 3 s tk kA 31.5 31.5 31.5 25 25
Rated peak withstand current Panels without HV HRC fuses Ip up to kA 50/63 50/63 50/63 50/63 50/-
Panels with HV HRC fuses Ip up to kA 80 80 80 63 63
Rated short-circuit making Transformer feeders2 Ima kA 80 80 80 63 63
current Ring-main feeders Ima up to kA 50/63 50/63 50/63 50/63 50/-
1
Depending on HV HRC fuse-link
2
Depending on let-through current of HV HRC fuse
Fuse protection table: Line protection of motor operating mechanism for three-
position switch
Rated voltage of Operating voltage1 Power consumption Rated current of Normal current Smallest possible rated
operating mechanism of motor operating mechanism current of the miniature
110% 80%
circuit-breaker
Ua [V] Umax [V] Umin [V] P [W] S [VA] Ia_A [A] Imax [A] Imin [A] Ia_S [A]
DC 24 26 19 150 – 6.3 7.8 5.7 6
30 33 24 150 – 5.0 6.3 4.5 6
32 35 26 150 – 4.7 5.9 4.3 6
48 53 38 150 – 3.1 3.9 2.8 4
60 66 48 150 – 2.5 3.1 2.3 3
110 121 88 150 – 1.4 1.7 1.2 2
120 132 96 150 – 1.3 1.6 1.1 2
125 138 100 150 – 1.2 1.5 1.1 2
127 140 102 150 – 1.2 1.5 1.1 2
220 242 176 150 – 0.7 0.9 0.6 1
240 264 192 150 – 0.6 0.8 0.6 1
AC 100 110 80 – 190 1.9 2.4 1.7 2
110 121 88 – 190 1.7 2.2 1.6 2
120 132 96 – 190 1.6 2.0 1.4 2
125 138 100 – 190 1.5 1.9 1.4 2
230 253 184 – 190 0.8 1.0 0.8 1
240 264 192 – 190 0.8 1.0 0.7 1
1
The operating voltage may deviate from the rated voltage specified in the table by –20% to +10%.

Description
10.11 Endurance classes

The switching devices of NXPLUS C switchgear conform to the classes according to IEC 62271-
100, -102 and -103.
Overview
Panel type Circuit-breaker Disconnector Switch-disconnector Earthing switch
Circuit-breaker panel M2 M1 E2 1
E2
C2
Bus sectionalizer panel M2 M1 E21
E2
C2
Disconnector panel M1 E0
Vacuum contactor M1 M1 E3 E2
panel2
Transformer panel M0 M1 E3 E2
Ring-main panel M1 M1 E3 E2
Metering panel M1 M1 E3 E2
1
By closing the circuit-breaker
2
For the switching device "vacuum contactor", no classes have been defined in the standard.
Circuit-breaker (standard)
Function Class Standard Property

BREAKING M2 IEC 62271-100 10000 times mechanically without maintenance
E2 IEC 62271-100 • 10000 times rated normal current
• 50 times rated short-circuit breaking current without
maintenance
C2 IEC 62271-100 Very low probability of restrikes
Circuit-breaker up to 15 kV, 31.5 kA, 1250 A (option)

BREAKING M2 IEC 62 271-100 30000 times mechanically with maintenance
E2 IEC 62 271-100 30000 times rated normal current
50 times rated short-circuit breaking current
C2 IEC 62 271-100 Very low probability of restrikes
Three-position disconnector (standard)

DISCONNECTING M1 IEC 62271-102 2000 times mechanically
READY-TO-EARTH M0 IEC 62271-102 1000 times mechanically
E0 IEC 62271-102 No making capacity
EARTHING E21 IEC 62721-200 50 times rated short-circuit making current I ma
IEC 62271-102
1
The EARTHING function with class E2 is reached by closing the circuit-breaker in combination with
the three-position disconnector (class E0)
Three-position disconnector up to 15 kV, 31.5 kA, 1250 A (option)

EARTHING E21 IEC 62721-200 50 times rated short-circuit making current I ma
IEC 62271-102
1

Description
Three-position disconnector up to 15 kV, 31.5 kA, 1250 A (option)

EARTHING E21 IEC 62271-200 50 times rated short-circuit making current Ima
IEC 62271-102
1
Three-position switch-disconnector (application in vacuum contactor panel, ring-main panel,

metering panel)

LOAD BREAKING M1 IEC 60265-1 1000 times mechanically
E3 IEC 60265-1 100 times rated mainly active load breaking current I11
5 times rated short-circuit making current Ima
EARTHING M0 IEC 62271-102 1000 times mechanically
E2 IEC 62271-102 5 times rated short-circuit making current Ima
1
In addition to I 1 the class also covers the test currents I 2ar, I4a, I4b, I6a and I6b
Three-position switch-disconnector (application in switch-disconnector panel)

LOAD BREAKING M1 IEC 60265-1 1000 times mechanically
E3 IEC 60265-1 1000 times mechanically
100 times rated mainly active load breaking current I11
5 times rated short-circuit making current Ima
EARTHING M0 IEC 62271-102 1000 times mechanically
E2 IEC 62271-102 5 times rated short-circuit making current Ima
1 In addition to I 1 the class also covers the test currents I 2ar, I4a, I4b, I6a and I6b
10.12 Vacuum contactor
Rated voltage 7.2/12/17.5/24 kV

Rated current 450 A
Rated short-time withstand current 8 kA (1 s)
Rated peak withstand current 20 kA
Number of operating cycles at rated normal 100 000 or 500 000 operating cycles
current:
Auxiliary switch 3 NO + 4 NC or 5 NO + 6 NC freely available
Counter Option
Short-circuit breaking current 4 kA

Description
Fuse protection table: Line protection of magnet coil for vacuum contactor
Rated voltage Operating voltage Power consumption Rated current of Normal current Smallest possible rated
of main coil main coil current of the
miniature circuit-
110% 80% Pickup Holding
breaker
Ua [V] Umax [V] Umin [V] P [W] Ia [A] Imax [A] DC Imin [A] DC Ia_S [A]
DC 110 121 88 3100 – 28.18 35.2 25.6 16
– 120 1.09 1.4 1.0
120 132 96 3100 – 25.83 32.3 23.5 16
– 120 1.00 1.3 0.9
125 138 100 3100 – 24.80 31.0 22.5 16
– 120 0.96 1.2 0.9
220 242 176 3700 – 16.82 21.0 15.3 10
– 145 0.66 0.8 0.6
VA Imax [A] AC Imin [A] AC
AC 110 121 88 3200 – 29.09 36.4 26.4 16
– 114 1.04 1.3 0.9
230 253 184 3200 – 13.91 17.4 12.6 10
– 114 0.50 0.6 0.5
240 264 192 3200 – 13.33 16.7 12.1 10
– 127 0.53 0.7 0.5
10.13 Insulating gas

The sealed pressure system of the switchgear contains the insulating gas SF 6 (fluorinated
greenhouse gas, GWP 22,800).
Example for a typical amount of SF6 gas: NXPLUS C circuit-breaker panel with 3.2 kg SF 6 (CO2e
= 73 t).
The respective amount of SF6 gas included is indicated on the rating plate of the switchgear.
Gas leakage rate The gas leakage rate is < 0.1% per year (referred to the absolute gas pressure).

Description
11 End of life
SF6 gas The equipment contains the fluorinated greenhouse gas SF6 registered by the Kyoto Protocol
with a global warming potential (GWP) of 22 800 2 .
CAUTION
Danger of suffocation and risk of environmental damages
A high concentration of SF6 in the air can cause suffocation. Larger amounts of SF 6 in the
atmosphere can cause environmental damages.
➭ SF6 has to be reclaimed and must not be released into the atmosphere.
➭ For use and handling of SF6, IEC 62271-4: High-voltage switchgear and controlgear - Part
4: Use and handling of sulphur hexafluoride (SF6) has to be observed.
Before recycling the materials, evacuate the SF 6 gas professionally and prepare it for further
use. For further information, please contact the Siemens Service Hotline.
Recycling The switchgear is an environmentally compatible product.

The components of the switchgear can be recycled in an environmentally compatible way by
dismantling into sorted scrap and residual mixed scrap.
Insulating gas SF6 has to be evacuated professionally as a reusable material and recycled. SF 6
must not be released into the environment.
After evacuating the SF6 gas, the switchgear mainly consists of the following materials:
• Galvanized steel (enclosure and operating mechanisms)
• Stainless steel (vessel)
• Copper (conductor bars)
• Silver (contacts)
• Cast-resin based on epoxy resin (bushings and fuse boxes)
• Plastic material (arcing chamber and fuse slide)
• Silicone rubber
The switchgear can be recycled in ecological manner in compliance with existing legislation.
Auxiliary devices such as short-circuit indicators have to be recycled as electronic scrap.
Any existing batteries have to be recycled professionally.
As delivered by Siemens, the switchgear does not contain hazardous materials as per the
Hazardous Material Regulations applicable in the Federal Republic of Germany. For operation
in other countries, the locally applicable laws and regulations must be observed.
For further information regarding declarable or restricted substances in this product, please
contact materialcompliance.ms.ehs@siemens.com .
2
Source: "Regulation (EU) No 517/2014 of the European Parliament and of the Council of 16th April 2014
on fluorinated greenhouse gases and repealing Regulation (EC) No 842/2006"

Installation
Installation
12 Constructional stipulations
12.1 Switchgear room

The switchgear can be used at the following locations as an indoor installation according to
IEC 61936 (Power Installations exceeding AC 1 kV) and VDE 0101:
• Lockable electrical service locations. Requirements on lockable electrical service locations
(room or location):
- Are exclusively used for operation of electrical equipment.
- Are kept under lock and key.
- Access is exclusively restricted to electricians and persons who have been properly
instructed in electrical engineering.
- Untrained or unskilled persons may only enter under the supervision of electricians or
persons who have been properly instructed in electrical engineering.
• Outside lockable electrical service locations at places which are not accessible to the public.
Enclosures of switchgear can only be removed with tools.
Preparing the switchgear Observe the following points when preparing the switchgear room:
room • Base frame and switchgear dimensions
• Transport ways to the switchgear room
• Distribution and intermediate storage spaces
• Size of the room and the doors
• Construction and load-bearing capacity of the floor
• Illumination, heating, power and water supply
• Dimensions of installation scaffoldings and foundation rails
• Installation of high-voltage cables
• Earthing system
• Switchgear room free of dirt and dust

Installation
Room planning
Fig. 40: Wall-standing arrangement (panels without pressure

relief duct)
Fig. 41: Wall-standing arrangement (panels with pressure
relief duct)
* Pressure relief duct: Depth 125 mm

** Depending on national requirements
Recommendation for panel replacement / panel extension:
Control aisle ≥ 1400 mm for panel with 600 mm panel width
Control aisle ≥ 1600 mm for panel with 900 mm panel width
*** Lateral wall distance on left or right ≥ 500 mm recommended
**** 125 mm, if there are exclusively 600 mm panels
Fig. 42: Free-standing arrangement (panels with pressure relief

duct)
Room height • NXPLUS C, all technical data, all types of installation: ≥ 2750 mm
• NXPLUS C, 25 kA 1 s and 3 s, 1250 A busbar, 761 mm low-voltage compartment:
≥ 2400 mm
• NXPLUS C with horizontal pressure relief duct: ≥ 2750 mm
Load data and minimum

Constant loads Vertical single load 8 / 14 kN1
distances
Not constant loads Live load 12 kN/m2
Minimum distances Control aisle 800 mm2
Wall distance on the left 50 mm3
Wall distance on the right 50 mm 3
Ceiling height 2750 (2400) mm
Minimum door opening Height 2500 mm
Width 900 / 1200 mm1
1
Depending on panel width 600 / 900 mm.
2
Depending on national requirements; for extension/panel replacement, a control aisle of at least
1400 mm (for panels with a panel width of 900 mm, at least 1600 mm) is recommended.
3
For wall-standing arrangement, a wall distance (on left or right) of at least 500 mm is recommen -
ded.

Installation
Construction of the floor

DANGER
Heavy weight
Will cause death, serious injury or property damage.
Properly support switchgear when moving across openings in floor.
➭ Use adequate bridging material to support switchgear when moving across openings in
floor.
➭ Ensure that load-bearing capacity of bridging materials is adequate.
➭ Secure bridging members to prevent displacement of bridging members during movement
of switchgear.
The floor covering must be even, easy to clean, pressure-resistant, slip-resistant, abrasion-
resistant and electrically discharging.
As floor construction, the following is possible:
Steel girder layer
Suitable for large and numerous floor openings, and advantageous for later modifications or
extensions of the switchgear. The frame construction should feature longitudinal and cross
girders to enable later panel replacements without problems. The dimensions result from the
constructional data of NXPLUS C (see page 84, "Constructional data of the foundation").
Fig. 43: Frame construction with Fig. 44: Frame construction with longitudinal and
longitudinal and cross girders cross girders (cable basement, example)
(example)
Reinforced-concrete plate
Suitable for small room dimensions or spans, as well as for few and smaller floor openings.
Double floor
Suitable if neither a cable basement nor sufficient cable ducts can be installed; it consists of
removable, flame-retardant floor plates mounted on a supporting structure. The supporting
floor is about 30 to 80 cm lower depending on the cable routing (bending radius).

Installation
Fig. 45: Double floor (example)
Earthing system • Important: Observe the corresponding national and international standards and building
regulations.
• Provide effective earthing system for the substation building (e.g. foundation earth
electrode, ring earth electrode, earth rod). Provide for the corresponding earthing
connection points inside the substation building.
• Connect components brought into the substation building - such as metallic constructions,
floor reinforcement, doors, pressure relief systems, cable tracks, etc. - to the substation
earth, and earth them.
• Dimension the cross-sections of the earth electrodes sufficiently (e.g. foundation earth
electrode, ring earth electrode, earth rod).
Cable basement
NOTICE
Incorrectly dimensioned cable basement
Can damage cables or cable connections.
➭ The cable basement must allow adequate space for connecting and laying the cables.
➭ Do not violate the minimum cable bending radius of the cables.
The cable basement must have the following characteristics:

• Dry
• Accessible at any time
• Sufficiently illuminated
12.2 Constructional data of the foundation

• A suitable foundation can be a false floor, a double floor or a reinforced-concrete
foundation. The reinforced-concrete floor must be equipped with foundation rails for
supporting the panels.
• As for design and construction of the foundation, the relevant standards DIN 43661
“Fundamentschienen in Innenanlagen der Elektrotechnik” (Foundation rails in electrical
indoor installations) and DIN 18202 “Maßtoleranzen im Hochbau” (Blatt 3) (Measuring
tolerances in structural engineering (Sheet 3)) apply.
• Dimensions of the floor opening and the fixing points of the switchgear frame (see page 85,
"Floor openings and fixing points" and see page 110, "Fastening the panel to the
foundation").

Installation
Stipulations for evenness Evenness/straightness tolerance according to DIN 43661: 1 mm for 1 m length, 2 mm over
and straightness the width of the complete switchgear.
• Determine level differences between the installation surfaces of the panels using a
measuring sheet, and compensate with shims (0.5 - 1.0 mm).
Fig. 46: Measuring sheet for the foundation (example)
Floor openings and fixing points
Fig. 47: Panel with 600 mm panel width Fig. 48: Panel with 900 mm panel width
① Left-side floor opening for control cables

② Pressure relief duct (option)
③ Fixing point
④ Fixing point (additionally for resistance against
shock, vibration, earthquakes)
⑤ Floor opening for high-voltage cables
⑥ Cable compartment / pressure relief duct
⑦ Right-hand floor opening for control cables (only
required for zero-sequence current transformers in
the cable basement)
⑧ Cross member
1 When only one cable is connected, the dimension is
reduced by 275 mm
2 45 mm for deep cable compartment cover
Fig. 49: Circuit-breaker panel with top-rear

cable connection

Installation
Fig. 50: Circuit-breaker panel (450 mm) Fig. 51: Auxiliary transformer panel
① Left-hand floor opening for control cables

② Pressure relief duct
③ Fixing point
④ Fixing point (option)
⑤ Floor opening for high-voltage cables1
⑥ Right-hand floor opening for control cables (only
required for zero-sequence current transformers in
the cable basement)
⑦ Cross member
Fig. 52: Air-insulated metering panel

1
Only for auxiliary transformer panels with lateral cable connection

Installation
Resistance against shock, vibration and earthquakes (option)

For fastening against shock, vibration and earthquakes, the panels must be equipped with
additional floor bracings. The panel and the floor bracings are bolted together onto the
foundation rails.
On panels with a panel width of 900 mm, an additional bracing bar must be mounted.
Fig. 54: Floor bracings for panel with a panel

Fig. 53: Floor bracings for panel with a width of 900 mm (view from the
panel width of 600 mm (view from rear)
the front)
① Floor bracing at the rear ③ Fixing point
② Floor bracing at the front ④ Bracing bar (only panel width of 900 mm)

Installation
Core drillings (incl. new plug systems)
INFORMATION
For proper installation of the cable plugs, the following must be observed:
➭ Observe the specifications of the cable manufacturers.
➭ Drilling diameters depend on the cable cross-section.
Core drillings
• Circuit-breaker panel (panel width 450 mm, 630 A, 800 A)
① 1st cable
② 2nd cable
③ 50...80 mm
Conductor distances
Make 1st cable 2nd cable
Plug type Distance [mm] Plug type Distance [mm]

3M 93-EE 705-6 383 93-EE 718-6 275
Nexans Euromold (K)400TB/G 383 --- ---
(K)440TB/G 383 --- ---
(K)430TB/G 383 (K)300PB/G 278
(K)480TB/G 383 (K)800PB/G 273
(K)484TB/G 383 (K)804PB/G 273
Südkabel SET 12/24 383 SEHDK 13.1/23.1 273
nkt cables CB xx-630 383 CB xx-630 283
CB 24-1250-2 383 CB 24-1250-2 283
CB 36-630(1250) 383 CB 36-630(1250) 273
Tyco Electronics Raychem RSTI-L56xx 383 RSTI-CC-L56xx 283
RSTI-58xx 383 RSTI-CC-58xx 283
RSTI-x95x 383 --- ---
GCA CJBxx-630 383 CJBKxx-630 268
ABB Kabeldon CSE-A xx630-xx 383 --- ---
CSE-A xx630-03 383 --- ---
Cellpack CTS 630A 24kV 383 CTKS 630A 24kV 268
Ample AQT3-15/630 383 AHT3-15/630 283
Solid-insulated bar Moser-Glaser --- ---
Preissinger 372 --- ---
Ritz --- ---

Installation
Core drillings
• Circuit-breaker panel (630 A, 1000 A)
• Disconnector panel (1000 A)
• Ring-main panel (630 A)
① 1st cable
② 2nd cable
③ 3rd cable
④ 50...80 mm
Conductor distances
Make 1st cable 2nd cable 3rd cable
Plug type Distance [mm] Plug type Distance [mm] Plug type Distance [mm]
3M 93-EE 705-6 448 93-EE 718-6 340 --- ---
93-EE 705-6 448 93-EE 705-6 275 --- ---
93-EE 715-6 448 93-EE 715-6 275 --- ---
Nexans Euromold (K)400TB/G 448 (K)400TB/G 203 --- ---
(K)440TB/G 448 (K)440TB/G 203 --- ---
(K)430TB/G 448 (K)300PB/G 343 (K)300PB/G 238
(K)480TB/G 448 (K)800PB/G 343 (K)800PB/G 238
(K)484TB/G 448 (K)804PB/G 338 (K)804PB/G 228
(K)489TB/G 448 (K)809PB/G 338 (K)809PB/G 228
Südkabel SET 12/24 448 SEHDK 13.1/23.1 338 --- ---
SET 12/24 448 SET 12/24 268 --- ---
SEHDT 13/23 448 SEHDT 13/23 203 --- ---
nkt cables CB xx-630 448 CB xx-630 268 --- ---
CB xx-630 448 CC xx-630 348 CC xx-630 248
CB 24-1250-2 448 CB 24-1250-2 268 --- ---
CB 24-1250-2 448 CC 24-1250-2 348 CC 24-1250-2 248
CB 36-630 (1250) 448 CB 36-630 (1250) 268 --- ---
CB 36-630 (1250) 448 CC 36-630 (1250) 338 CC 36-630 (1250) 228
CB 42-1250-3 448 CC 42-2500-3 321 CC 42-2500-3 194
Tyco Electronics RSTI L56xx 448 RSTI -CC-L56xx 348 RSTI-CC-L56xx 248
Raychem RSTI 58xx 448 RSTI -CC-58xx 348 RSTI-CC-58xx 248
RSTI-x95x 448 RSTI-CC-x95x 328 RSTI-CC-x95x 208
RSTI x6Lxx 448 RSTI -x6Lxx 273 --- ---

Installation
GCA CJBxx-630 448 CJBKxx-630 333 --- ---
ABB Kabeldon CSE-A xx630-xx 448 CSE-A xx630-xx 276 --- ---
CSE-A xx630-03 448 CSE-A xx630-03 268 --- ---
Cellpack CTS 630A 24kV 448 CTS 630A 24kV 241 --- ---
CTS 630A 24kV 448 CTKS 630A 24kV 333 CTKS 630A 24kV 218
Ample AQT3-15/630 448 AHT3-15/360 348 --- ---
Solid-insulated bar Moser-Glaser 437 --- --- --- ---
Preissinger ---
Ritz ---

Installation
Core drillings
• Circuit-breaker panel (1250 A)
• Disconnector panel (1250 A)
① 1st cable
② 2nd cable
③ 3rd cable
④ 4th cable
⑤ 50...80 mm
Conductor distances
Make 1st cable 2nd cable 3rd cable 4th cable
Plug type Distance Plug type Distance Plug type Distance Plug type Distance
[mm] [mm] [mm] [mm]
3M 93-EE 705-6 595 93-EE 718-6 485 --- --- --- ---
93-EE 705-6 595 93-EE 705-6 425 --- --- --- ---
93-EE 715-6 595 93-EE 715-6 425 --- --- --- ---
Nexans (K)400TB/G 595 (K)400TB/G 350 (K)400TB/G 105 --- ---
Euromold (K)440TB/G 595 (K)440TB/G 350 (K)440TB/G 105 --- ---
(K)430TB/G 595 (K)300PB/G 490 (K)300PB/G 385 (K)300PB/G 280
(K)489TB/G 595 (K)809PB/G 485 (K)809PG/G 375 (K)809PB/G 265
Südkabel SET 12/24 595 SEHDK 13.1/23.1 485 --- --- --- ---
SET 12/24 595 SET 12/24 415 --- --- --- ---
SEHDT 13/23 595 SEHDT 13/23 350 --- --- --- ---
nkt cables CB xx-630 595 CB xx-630 415 CB xx-630 235 --- ---
CB xx-630 595 CC xx-630 495 CC xx-630 395 --- ---
CB 24-1250-2 595 CB 24-1250-2 415 CB 24-1250-0 235 --- ---
CB 24-1250-2 595 CB 24-1250-2 495 CC 24-1250-2 395 CC 24-1250-2 295
CB 36-630 (1250) 595 CB 36-630 (1250) 415 CB 36-630 (1250) 235 --- ---
CB 36-630 (1250) 595 CC 36-630 (1250) 485 CC 36-630 (1250) 375 --- ---
CB 42-1250-3 595 CC 42-2500-3 468 CC 42-2500-3 341 CC 42-2500-3 214
Tyco Electronics RSTI-L56xx 595 RSTI -CC-L56xx 495 RSTI -CC-L56xx 395 --- ---
Raychem RSTI-58xx 595 RSTI -CC-58xx 495 RSTI -CC-58xx 395 RSTI-CC-58xx 295
RSTI-x95x 595 RSTI-CC-x95x 475 RSTI-CC-x95x 355 --- ---
RSTI-x6Lxx 595 RSTI -x6Lxx 420 RSTI -x6Lxx 245 --- ---
GCAGCA CJBxx-630 595 CJBKxx-630 480 --- --- --- ---
ABB Kabeldon CSE-A xx630-xx 595 CSE-A xx630-xx 423 --- --- --- ---
CSE-A xx630-03 595 CSE-A xx630-03 415 --- --- --- ---

Installation
Make 1st cable 2nd cable 3rd cable 4th cable
[mm] [mm] [mm] [mm]
Cellpack CTS 630A 24kV 595 CTS 630A 24kV 388 --- --- --- ---
CTS 630A 24kV 595 CTKS 630A 24kV 480 CTKS 630A 24kV 365 --- ---
Ample AQT3-15/630 595 AHT3-15/630 495 --- --- --- ---
Solid-insulated Moser-Glaser 584 --- --- --- --- --- ---
bar Preissinger
Ritz
Core drillings
• Circuit-breaker panel (630 A, 1000 A, 1250 A)
• Disconnector panel (1000 A, 1250 A)
• Ring-main panel (630 A)
① 1st cable
② 2nd cable
③ 3rd cable
④ 50...80 mm
Deep floor cover:
Conductor distances
3M 93-EE 705-6 521 93-EE 718-6 371 --- ---
93-EE 705-6 521 93-EE 705-6 371 --- ---
93-EE 715-6 521 93-EE 715-6 371 --- ---
Nexans Euromold (K)400TB/G 521 (K)400TB/G 371 --- ---
(K)430TB-630 521 (K)300PB-630 371 (K)300PB-630 221
Südkabel SET 12/24 521 SEHDK 13.1/23.1 371 --- ---
SET 12/24 521 SET 12/24 371 --- ---
nkt cables CBxx-630 521 CBxx-630 371 --- ---
CBxx-630 521 CCxx-630 371 CCxx-630 221
Tyco Electronics RSTI L56xx 521 RSTI -CC-L56xx 371 RSTI -CC-L56xx 221
Raychem RSTI L58xx 521 RSTI -CC-58xx 371 RSTI -CC-58xx 221

Installation
Core drillings
• Circuit-breaker panel (2000 A, 2500 A)
• Disconnector panel (2000 A, 2500 A)
① 1st/2nd cable
② 3rd/4th cable
③ 5th/6th cable
④ 7th/8th cable
⑤ 50...80 mm
* The distance of the bushings in
the vessel is 100 mm.
Conductor distances
Make 1st/2nd cable 3rd/4th cable 5th/6th cable 7th/8th cable
[mm] [mm] [mm] [mm]
3M 93-EE 705-6 595 93-EE 718-6 485 --- --- --- ---
93-EE 705-6 595 93-EE 705-6 425 --- --- --- ---
93-EE 715-6 595 93-EE 715-6 425 --- --- --- ---
Nexans (K)400TB/G 595 (K)400TB/G 350 (K)400TB/G 105 --- ---
Euromold (K)440TB/G 595 (K)440TB/G 350 (K)440TB/G 105 --- ---
Südkabel SET 12/24 595 SEHDK 13.1/23.1 485 --- --- --- ---
SET 12/24 595 SET 12/24 415 --- --- --- ---
SEHDT 13/23 595 SEHDT 13/23 350 --- --- --- ---
nkt cables CBxx-630 595 CBxx-630 415 CCxx-630 235 --- ---
CBxx-630 595 CCxx-630 495 CCxx-630 395 --- ---
CB 24-1250-2 595 CB 24-1250-2 415 CB 24-1250-2 235 --- ---
CB 24-1250-2 595 CC 24-1250-2 495 CC 24-1250-2 395 CC 24-1250-2 295
CB36-630 (1250) 595 CB36-630 (1250) 415 CC 36-630 (1250) 235 --- ---
CB 36-630 (1250) 595 CC 36-630 (1250) 485 CC 36-630 (1250) 375 --- ---
Tyco Electronics RSTI-L56xx 595 RSTI -CC-L56xx 495 RSTI -CC-L56xx 395 --- ---
Raychem RSTI-58xx 595 RSTI -CC-58xx 495 RSTI -CC-58xx 395 RSTI-CC-58xx 295
RSTI-x95x 595 RSTI-CC-x95x 475 RSTI-CC-x95x 355 --- ---
RSTI x6Lxx 595 RSTI -x6Lxx 420 RSTI -x6Lxx 245 --- ---
GCA CJBxx-630 595 CJBKxx-630 480 --- --- --- ---
ABB Kabeldon CSE-A xx630-xx 595 CSE-A xx630-xx 423 --- --- --- ---
CSE-A xx630-03 595 CSE-A xx630-03 415 --- --- --- ---
Cellpack CTS 630A 24kV 595 CTS 630A 24kV 388 --- --- --- ---
CTS 630A 24kV 595 CTKS 630A 24kV 480 CTKS 630A 24kV 365 --- ---

Installation
Make 1st/2nd cable 3rd/4th cable 5th/6th cable 7th/8th cable
[mm] [mm] [mm] [mm]
Ample AQT3-15/630 595 AHT3-15/630 495 --- --- --- ---
Solid-insulated Moser-Glaser 584 --- --- --- --- --- ---
bar Preissinger
Ritz
12.3 Transport units
Transport dimensions and transport weights
Transport Panel spacing Transport dimensions Transport weight [approx. kg] 1

Width x Height x Depth
[mm] [mm] x [mm] x [mm] with packing without packing

Rail or truck 1 x 450 1100 x 2460 x 1450 900 800
1 x 600 1100 x 2460 x 1450 900 800
1x 600 (top-rear cable 1100 x 2460 x 2100 900 800
connection)
1 x 900 1100 x 2460 x 1450 13002 / 1500 12002 / 1400
Auxiliary transformer 800 x 1200 x 1200 500 425
Ship or 1 x 450 1130 x 2550 x 1450 900 800
airplane 1 x 600 1130 x 2550 x 1450 900 800
1x 600 (top-rear cable 1130 x 2550 x 2100 900 800
connection)
1 x 900 1130 x 2550 x 1450 13002 / 1500 12002 / 1400
Auxiliary transformer 800 x 1200 x 1200 500 425
1
Average value, depending on the degree to which the panel is equipped
2 Auxiliary transformer panel and air-insulated metering panel
Center of gravity The center of gravity of NXPLUS C (all panels) is located at the following position:
Position of the center of gravity

Panel width 600 mm Panel width 900 mm Panel width 600 mm and top-rear cable connection
① Low-voltage compartment ② Pressure relief duct
The center of gravity is identified with the following symbol (arrow):

Installation
Fig. 55: Symbol for the center of gravity
The symbol for the center of gravity is attached on both sides of the panel.
Transport regulations According to "Annex A of the European Agreement Concerning the International Carriage of
Dangerous Goods by Road (ADR)", Siemens gas-insulated medium-voltage switchgear does
not belong to the category of dangerous goods in respect of transportation, and is exempted
from special transport regulations according to ADR, Clause 1.1.3.1 b).

Installation
13 Before installation
13.1 Preliminary clarifications

In order to load the transport units in a suitable installation order, the regional Siemens
representative requires the following information from you several weeks before delivering the
switchgear:
• Sketch of the installation room including the locations and numbers of the individual panels
and the storage space for the accessories
• Sketch of the access route from the public road to the switchgear building and information
concerning the condition thereof (meadows, arable soil, sand, gravel, etc.)
• Sketch of the transport route inside the switchgear building with the locations and
dimensions of doors and other narrow points, as well as the floor number of the installation
room
• Information about available lifting equipment, e.g. mobile crane, fork-lift truck, lifting truck,
hydraulic jack, roller pads. If no lifting equipment is available, please notify this explicitly
13.2 Intermediate storage
WARNING
Overloading of the storage space
Can cause serious injury. Can damage the storage place or the stored goods.
➭ Observe the load-bearing capacity of the floor.
➭ Do not stack the transport units.
➭ Do not overload lighter components by stacking.
WARNING
Fire risk
The transport unit is packed in flammable materials.
➭ No smoking.
➭ Keep fire extinguishers in a weatherproof place.
➭ Mark the location of the fire extinguisher.
NOTICE
Damaged packings of desiccant bags
Can cause corrosion of switchgear parts and formation of creepage distances by high air
humidity.
In the ambient air, the desiccant bags lose their effectiveness and cannot be used anymore.
➭ Do not damage or remove packing of desiccant bags.
➭ Do not unpack desiccant bags before use.
NOTICE
Outdoor storage of unpacked transport units
Can damage the transport units.
➭ Store transport units outdoors packed in seaworthy crates and in a weatherproof place.
If the comprehensive accessories, the delivered switchgear or parts thereof have to be stored
before installation, a suitable storage room or place has to be selected and prepared.
Intermediate storage of the transport units:
• In original packing as far as possible
• Observe the permissible storage temperature from -25 °C to +70 °C in accordance with the
installed secondary devices

Installation
• In a weatherproof place
• Protected against damage
• If packed in seaworthy crates, the switchgear can be stored for a maximum of 6 months
(desiccant bags)
• Store transport units in such a way that they can be taken out later in the correct order for
installation
Switchgear storage in Store the switchgear in a closed room. The storage room must have the following
closed rooms characteristics:
• Floor with adequate load-bearing capacity (weights as per delivery note)
• Even floor to enable stable storage.
• Well-ventilated and as free of dust as possible
• Dry and protected against humidity and vermin (e.g. insects, mice, rats)
• Heatable up to at least 2 °C above outside temperature to prevent condensation.
• Check humidity in the packings every 4 weeks (condensation)
• Do not unpack small parts to avoid corrosion and loss.
Outdoor storage of If the switchgear or parts thereof are delivered in seaworthy crates, the crates can be stored up
switchgear packed in to 6 months in other rooms or outdoors. The storage place must have the following
seaworthy crates characteristics:
• Floor with adequate load-bearing capacity (weights as per delivery note)
• Roofed, protected against humidity (rain water, flooding, melting water from snow and ice),
pollution, vermin (rats, mice, termites, etc.) and unauthorized access
• For protection against floor humidity, place all crates on planks and square timber.
• After 6 months of storage, have the desiccant agent regenerated professionally. To do this,
ask for expert personnel via the regional Siemens representative
13.3 Tools/auxiliary means

Before starting to work on the switchgear, provide for the tools/auxiliary means required:
• Hexagonal screwdriver insert (min. length 140 mm) for hexagon socket-head bolt 10 mm
DIN 7422
• Torx screwdriver Tx25
• Torque wrench 20 - 50 Nm
• Ratchet, reconnectable DIN 3122
• Extension DIN 3123 40 - 125
• Socket spanner inserts DIN 3124, socket spanner inserts size 17, 18 and 19, min. length
80 mm
• Water level
• Lifting truck
• Reinforcing bars, roller crowbars
• Transport rollers, tubes
• Lifting rods, length 753 mm, Ø 20 mm, e.g. certified lifting rods (order number 802-9047.3,
to be procured from the regional Siemens representative)
• Lifting rods, length 1053 mm, Ø 20 mm, e.g. certified lifting rods (order number 804-
0011.3, to be procured from the regional Siemens representative)
• Technical requirements for lifting rods:
- Diameter: 20 mm
- Loading capability (yield strength): R e ≧ 780 MPa (N/mm2)
• Lint-free cleaning paper
• Wiping cloths
• Grinding sponge with corundum grit 100
• Abrasive fabric

Installation
Set of assembly facilities The "set of assembly facilities" (order no.: 802-9035.3, available at the regional Siemens
representative) is recommended. The "set of assembly facilities" comprises the following
auxiliary means:
• Certified lifting rods (crane rods) for lifting or lowering panels with panel widths of 600 mm
and 900 mm
- 2 lifting rods: Length 753 mm, Ø 20 mm
- 2 lifting rods: Length 1053 mm, Ø 20 mm
• 1 set with 4 ring eyes, washers and hexagon nuts each, for lifting low-voltage
compartments
• 1 handle for lifting or lowering voltage transformers type 4MT2 or 4MT3
• 12 supporting feet for secure standing of the panels
• 1 lever for removing the silicone insert of voltage transformers type 4MT3
• 1 voltage transformer assembly jack (scissor-type jack) for lifting or lowering voltage
transformers type 4MT3
• 3 extraction tools for the screw-type cone of the busbar
• 2 gauges for assembling the busbars
• 2 gauges for aligning panels with double busbars
• 2 tools for charging the circuit-breaker operating mechanism
• 1 adapter for emergency operation of the three-position switch
• 2 adjustment tools for aligning the switchgear vessels
13.4 Comments on electromagnetic compatibility

To achieve appropriate electromagnetic compatibility (EMC), some basic requirements must
be observed while erecting the switchgear. This applies especially to the installation and
connection of external cables and wires.
Basic measures for ensuring EMC are already taken during design and assembly of the
switchgear panels. Among other things, these measures include:
• The low-voltage compartment is an integral part of the panel, which means that the
protection and control devices with the internal wiring are metal-enclosed.
• Reliable earth connections of the frame parts via toothed contact washers or locking
washers.
• Inside the panel, wires are laid in metal ducts.
• Spatial separation of sensitive signal wires from wires with high interference voltage levels.
• Limitation of switching overvoltages of inductive loads (e.g. relay or contactor coils, motors)
by means of protective circuits with diode, varistor or RC element.
• Within the low-voltage compartment, the secondary devices are mounted in defined zones.
• Shortest possible connection between corresponding modules in subracks.
• Consideration of the magnetic leakage fields of conductor bars and cables.
• Protection of subracks and wiring backplanes against interference by perforated shielding
plates.
• Large surface bonding between all modules and devices as well as bonding to the earthing
conductor of the switchgear assembly.
These measures basically enable proper operation of the switchgear itself. The planner or
operator of the switchgear must decide whether additional measures are required depending
on the electromagnetic environment where the switchgear is installed. Such measures must
be implemented by the installation company in charge.
In an environment with heavy electromagnetic interference it may be necessary to use
shielded cables and wires for the external connections. This makes it possible to avoid
interferences in the low-voltage compartment and thus, undesired influences on the
electronic protection and control or other automation devices.
Cable shields must be electrically bonded to be able to carry high frequencies, and contacted
concentrically at the cable ends.
The shields of cables and wires are connected and earthed in the low-voltage compartment.

Installation
Connect the shields to earth potential - with high electrical conductivity and all around as far
as possible. Protect the contact surfaces from corrosion in case of humidity (regular
condensation).
When laying cables into the switchgear assembly, separate the control, signaling and data
cables and other lines with different signal and voltage levels, e.g. by laying them on separate
racks or riser cable routes.
Corresponding to the different shield designs, there is a number of methods to perform
connection. The planning department or site management determines which of the methods
will be used, taking EMC requirements into account. The preceding points should always be
taken into account.
The shield is connected to cables or wires with clamps contacting all around. If low demands
are placed on EMC, it is also possible to connect the shield directly to earth potential (combine
or twist the shield wires) or via short cable connections. Use cable lugs or wire-end ferrules at
the connecting points.
Always keep the connecting leads of the shields as short as possible (< 10 cm).
If shields are used as protective earth conductors at the same time, the connected plastic-
insulated lead must be marked green/yellow over its entire length. Non-insulated connections
are inadmissible.

Installation
14 Unloading and erecting the switchgear
14.1 Packing and transport unit
Packing The transport units can be packed as follows:

• On pallets, covered with PE protective foil
• In a seaworthy crate (switchgear is sealed with desiccant bags in PE foil)
• Other packings in special cases
NOTICE
Disposal of packing and consumables
Incorrectly disposed of packings and consumables can pollute the environment.
➭ Packing and consumable materials of the switchgear must be disposed of in an
environmentally compatible way or recycled.
➭ Observe local regulations for disposal and environmental protection.
Transport unit Transport units consist of:

• Individual panels, if applicable with separate low-voltage compartment
• Accessories including busbars
14.2 Completeness and transport damages
Checking for ➭ Check whether the delivery is complete and correct using the delivery note and packing
completeness lists.
➭ Compare the serial number of the switchgear panels on the delivery note with that on the
packing and the rating plates of the panels.
➭ Check whether the accessories are complete.
Checking for transport ➭ Temporarily open the packing in a weatherproof place to detect hidden damages. Stick the
damages PE foil together again and do not remove it totally until reaching the final mounting position
in order to keep the switchgear as clean as possible.
➭ Check the ready-for-service indicator for SF6 gas (see page 105, "Checking the ready-for-
service indicator").
➭ Inform the forwarding agent immediately about any defects or transport damages; if
required, refuse to accept the delivery.
➭ As far as possible, document larger defects and transport damages photographically;
prepare a damage report and inform your regional Siemens representative immediately.
➭ Have the transport damages repaired, otherwise you may not start installation.
➭ Refit the packing.

Installation
14.3 Unloading and transporting to place of installation
DANGER
Transport units falling down
Can cause death, serious injury, or damage the transport units.
The transport units can slip off due to mistakes during transport or while unloading from the
lifting gear.
➭ There must be no persons standing in the swinging area of lifted transport units.
➭ The ropes must not exert any forces on the panel walls under load. Attach ropes far away
on the hoisting tackle.
➭ Observe the dimensions and weights of the transport unit (delivery note).
➭ Please ensure that the lifting and transport gear used meets the requirements as regards
construction and load-bearing capacity.
➭ Observe the center of gravity of the transport units.
➭ Do not climb onto the roof of the panels.
➭ If the low-voltage compartment is removed: Do not step on the mounting plates of the
low-voltage compartment.
➭ Observe the instructions on the packing.
➭ Move the transport units in packed condition for as long as possible. Leave the transport
units packed after unloading for as long as possible.
➭ Do not damage the PE protective foil.
➭ Attach ropes to the hoisting tackle.

➭ Sling the ropes around the ends of the wooden pallet.
➭ Unload the transport units and set them down as close to the switchgear building as
possible in order to avoid unnecessary ways.
➭ Thoroughly clean the switchgear room, since extreme cleanliness is required during
installation.
➭ Move the transport units on their wooden pallets as far as possible.
➭ Move the transport units to the switchgear room in the order of installation.
➭ Move the transport units inside the building to the place of installation using a lifting truck,
fork-lift truck or rollers.
➭ Set the transport units down in the correct sequence directly in front of the place of
installation (leave a clearance for installation).
Removing from the If the panels are equipped with an interlock for the cable compartment cover or with a locking
wooden pallets device, the panels must be earthed to remove the cable compartment cover.
➭ Remove the PE film.
➭ Undo the bolted joints of the cable compartment cover.
➭ Push the lever of the locking device ① or of the interlock ② upwards and hold it.

Installation
① "Feeder earthed"
locking device
② Interlock for cable
compartment cover
➭ Lift the cable compartment cover and remove it upwards.

➭ Identify the cable compartment cover with the panel number.
➭ Take the transport bolts out and remove the metal plates placed underneath.
➭ Refit the cable compartment cover to keep the panels more rigid for further transport.
Further transport without

wooden pallets WARNING
Heavy weight.
Can cause death, serious injury or property damage.
➭ Observe all handling instructions in this manual to prevent tipping or dropping of
equipment.
CAUTION
Incorrect dimensioning of the lifting tools
Can damage the lifting eyes.
If the lifting eyes are damaged, the transport units cannot be aligned properly with other
switchgear panels.
➭ Maximum permissible angle of lifting equipment at the hook < 60°.
➭ Maximum permissible angle at the switchgear panel > 60°.
➭ Minimum permissible length of the hanging parts > 3000 mm.
INFORMATION
A transport unit standing on roller pads can only be moved straight ahead.
➭ To change the direction, the position of the roller pads must be changed.
➭ Lift the transport unit by means of a crane, hydraulic jacks or a fork-lift truck with the help of
lifting rods (before lifting, knock the boards marked at the front out of the wooden pallet by
means of a fork-lift truck).

Installation
For further information to usable lifting rods, see page 97, "Tools/auxiliary means".
Fig. 56: Craning with lifting rods (diameter of lifting rods, 20 mm)
➭ Lower the transport unit onto roller pads, reinforced rollers or tubes (approx. 30 mm
diameter). Distribute the roller pads so as to support the transport unit at the outer edges
and at the joints between the panels.
➭ Lift one side, then the other side of the transport unit with roller crowbars and slowly lower
it on the mounting position. Apply the roller crowbars only at the corners of the transport
units.
Craning end panels In the end panels there are openings for inserting the crane rods in the side walls.
Fig. 57: Openings for crane rods
➭ To insert the crane rods, undo the Torx bolts, push them upwards through the slot and
tighten them. The openings for the crane rods are released.
Fig. 58: Releasing the openings for the crane rods
➭ Insert the crane rods into the openings.

Installation
Fig. 59: Craning the end panel (schematic representation)
➭ After craning, close the openings again. Undo the Torx bolts again and push them back to
the initial position. Tighten the Torx bolts.
Installing the transport You may only start installing the transport units when
units • all transport damages have been repaired
• the base frame has been levelled (1 mm/m), see DIN 43661
• the SF6 gas filling in the vessels has been checked (see page 105, "Checking the ready-for-
service indicator").
• the accessories and the required material are complete (see page 96, "Before installation").
➭ Place the first (i.e. rearmost) transport unit as exactly as possible on its final location and
place the second one close to it, keeping a small distance so that the units can still be
aligned before bolting together.
➭ Remove packing and transport materials from the place of installation.
➭ Remove any dirt occurred during transport, as extreme cleanliness is required during
installation.
✔ Now the transport units are in the correct order for assembly.
Craning the low-voltage ➭ Mount four ring eyes with washers and hexagon nuts at the low-voltage compartment.
compartment ➭ Insert lifting rods through the ring eyes (diameter of lifting rods: 20 mm).
① Ring eye with hexagon nut

and washer
② Low-voltage compartment
Fig. 60: Craning the low-voltage compartment
➭ Mount the lifting gear.

✔ Now the low-voltage compartment can be lifted onto the panel.

Installation
14.4 Checking the ready-for-service indicator

Before starting assembly work, check the service readiness of the switchgear.
➭ Read the ready-for-service indicator, see page 189, "Ready-for-service indicator".
✔ If the pointer is in the green area, the gas filling is in order.
➭ If the pointer is in the red area, contact the Siemens Service Hotline.
Checking the signaling During transport, the signaling switch of the ready-for-service indicator can latch tight in the
switch red area due to extreme vibrations.
To put the ready-for-service indicator into operation again, the plastic part fixed at the
signaling switch must be brought to the initial position again by hand.
➭ Remove the front cover. To do this, undo 2 or 4 bolts at the bottom end of the front cover -
depending on the panel width - and take off the front cover.
➭ Push the plastic part ① at the signaling switch ② downwards with the index finger until the
ready-for-service indicator jumps back to the green area. When pushing the plastic part at
the signaling switch down from the latched position, a mechanical resistance must be
overcome. To prevent it from being damaged, the plastic part must be supported with one
finger while pushing down.
✔ Then, the pointer must return to the green area automatically. If not, please stop the
installation and contact the regional Siemens representative.
Fig. 61: Position of ready-for-service indicator for a 600 mm panel with 30000 operating
cycles
Fig. 62: 600 mm panel (zoom shows view after removal of the front plate)
Fig. 63: 900 mm panel (zoom shows view from the rear)

Installation
Fig. 64: Pointer position after operation of the plastic part at the signaling switch

Installation
15 Assembling the switchgear

In the instructions given in the following sections it is assumed that a new switchgear is being
installed which has not yet been connected to the mains, and that it is therefore not live.
DANGER
Hazardous voltage.
Will cause death, serious injury and property damage.
Always observe the Five Safety Rules:
➭ Isolate.
➭ Secure against reclosing.
➭ Verify safe isolation from supply.
➭ Earth and short-circuit.
➭ Cover or barrier adjacent live parts.
NOTICE
Functional failure due to pollution
Pollution or stepping on the switchgear can lead to functional failures during operation.
➭ Avoid any work that could pollute the switchgear (e. g. sawing, filing, painting or
plastering in the switchgear room, etc.).
➭ Do not step on the switchgear.
NOTICE
Damage to the operating mechanism
Undoing the sealed bolts can damage the Siemens high-voltage vacuum contactor.
Components inside the operating mechanism can come loose.
➭ Do not remove the bolts sealed with wax.
➭ If the sealing wax is broken, contact the regional Siemens representative.
Fig. 65: Bolts with sealing wax at the Siemens high-voltage vacuum contactor

Installation
15.1 Aligning and joining the panels
INFORMATION
Lining up the auxiliary transformer panel with lateral cable connection as an end panel
Particularities for lining up depending on the mounting direction and the position of the
auxiliary transformer panel as an end panel:
Auxiliary transformer panel as left or right end panel
• To enable working on the lateral cable connection, a wall distance of ≥ 500 mm must be
available.
Auxiliary transformer panel as right end panel
• It is recommended to line up from right to left
• Before being able to line up panels to the left, all installation work at the lateral cable
connection must have been completed.
• Lining up from left to right:
- Position the right end panel at a distance of ≥ 500 mm from the installed panels.
- Mount the cable at the lateral cable connection.
- Line up the right end panel with the existing panels.
- If work has to be executed at the lateral cable connection after lining up the right end panel,
the end panel must be removed again.
INFORMATION
To interconnect the panels (busbar interconnection of panels) more easily, already pre-
assembled low-voltage compartments can be removed for interconnecting the panels. Low-
voltage compartments on end panels may remain mounted.
➭ Remove pre-assembled low-voltage compartments.
Aligning the panels The first panel is on its mounting position and the others are placed at a small distance.
➭ Align the first panel laterally.
➭ Lay shims under the panels to align them in vertical and horizontal position.
➭ Carefully approach the next panel to the one that has already been aligned.
➭ Align the approached panel by means of the alignment brackets provided at the vessel. If
required, use shims to align the panel vertically and at the necessary height.
Mounting the sealing

strip INFORMATION
Panels that were intended for free-standing arrangement, but implemented in wall-mounting
arrangement, cannot be taken out of the switchgear assembly if the sealing strips are
mounted.
➭ Do not mount sealing strips on panels provided for wall-standing arrangement.
In case of free-standing arrangement of the switchgear, mount the sealing strips on the rear
wall of the switchgear.
➭ Mount the sealing strips on the rear wall of the switchgear. To mount the sealing strips, use
the M5x45 Torx bolts from the pressure relief duct. Take the other bolts from the
supplementary equipment.

Installation
① Sealing strips
Fig. 66: Mounting the sealing strips
Joining the panels

① Alignment bracket
② Fixing lug
③ Spacer
Fig. 67: Joining the panels
➭ Bolt the panels together at the alignment brackets ① using 2 panel connecting bolts M8x20
and nut-and-washer assemblies M8 each (tightening torque: 30 Nm). The usable fixing
points depend on the panel types.
Check the reference dimension K1 between the bushings (see page 111, "Assembling the
busbars"). If necessary, insert spacers between the alignment brackets of the panels. The
spacers are supplied with the supplementary equipment.
INFORMATION
The cable compartment covers can be coded, and the operating mechanism covers are
designed specifically for each panel. Any removed cable compartment covers and operating
mechanism covers must therefore be mounted on the same panels again.
➭ Write the corresponding panels numbers on all covers before removal.

Installation
➭ Remove the cable compartment cover and the front cover.

➭ Insert the panel connecting bolts M8x20 provided at the 4 fixing lugs ② of the right-hand
panel through the switchgear frame and bolt together with the left-hand panel (tightening
torque: 30 Nm).
➭ Check whether the bolted panels are in vertical position.
➭ Move each additional panel into position and align with the installed panels. Bolt the
alignment brackets and the frames together.
15.2 Fastening the panel to the foundation

The panel must be bolted together with the foundation rails at the fixing points in the base
frame.
➭ Bolt each panel diagonally to the foundation at 2 fixing points at least, see page 85, "Floor
openings and fixing points".
Use at least 2 fixing bolts M8 or M10 (tightening torque M8: 30 Nm, M10: 60 Nm).
➭ Resistance against shock, vibration and earthquakes: Install additional floor bracings in
every panel, see page 87, "Resistance against shock, vibration and earthquakes (option)".
Bolt each panel to the foundation at 4 fixing points.
Use 4 fixing bolts M8 or M10 (tightening torque M8: 30 Nm, M10: 60 Nm).
15.3 Removing transport braces

To assure the stability of the switchgear during transport, all panels with a pre-assembled low-
voltage compartment are equipped with transport braces. To install the switchgear, the
transport braces must be removed.
① Transport braces
➭ Remove the nuts and bolts of the transport braces.
➭ Remove the transport braces.

✔ The transport braces are removed.

Installation
15.4 Assembling the busbars

The components of the busbars are delivered separately with the accessories.
• To simplify installation, remove pre-assembled low-voltage compartments, if required.
• Before assembling the busbars, all panels must have been bolted together (see page 108,
"Aligning and joining the panels").
• Remove any current transformers pre-assembled on the busbar (for 1250 A busbar system).
• Current transformers in oval design for the twin busbar system can remain mounted.
CAUTION
Flashovers due to insufficient electrical contact, or pollution of the push-on surfaces
Damage to the busbars during operation.
➭ All busbar assembly work must be carried out with particular care.
➭ Check the contact surfaces and the silicone surfaces for damages before assembly.
➭ Observe extreme cleanliness.
➭ No smoking.
➭ Do not unpack busbars, cross adapters and end adapters until right before assembly.
➭ Brush oxidized copper surfaces bright, clean and grease them with the supplied mounting
paste before connection.
➭ Use the supplied mounting paste only.
➭ Tighten all bolted joints with correct torque. On all bolted joints, execute a torque test with
the torque wrench. Afterwards, mark the bolted joints on the nut with a waterproof pen
(perform this step only after consultation with the switchgear operator).
NOTICE
Busbars from different manufacturers
For the combination of busbars from different manufacturers, no responsibility is
assumed.
➭ Within one switchgear assembly, do only install busbars from a single manufacturer; if
necessary, contact the Siemens Hotline.
➭ Compare the manufacturers by means of the imprint on the busbars.
Fig. 68: Comparing manufacturer imprint of busbars
NOTICE
Damage to the auxiliary switch at the three-position disconnector
Can cause incorrect electrical position indications.
The load can deform the mounting plate for the low-voltage compartment and damage the
auxiliary switch in the operating mechanism compartment.
➭ Do not load the mounting plate directly.
➭ Place a board on the mounting plates in order to distribute the load evenly:
- Board with min. 1200 mm length for 600 mm wide panels
- Board with min. 1800 mm length for 900 mm wide panels

Installation
① Mounting plate of low-

voltage compartment
Phase sequence
① Phase L1
② Phase L2
③ Phase L3
Fig. 69: Phase sequence of bushings (view from the right)

Installation
Busbars (overview)
① Cap
② Contact half-shell
③ Busbar
④ Adjustment component
⑤ End adapter
⑥ Busbar insulation
⑦ Earthing cable
⑧ Bushing
⑨ Earthing connection
⑩ Cross adapter
⑪ Threaded stud M12/M16
⑫ Conical spring washer,
DIN 6796-12
⑬ Hexagon nut, ISO 4032-M 12
⑭ Screw-type cone
⑮ Coupling end adapter
Fig. 70: Busbar for busbar current up to 1250 A Copper washer, galvanized
⑯
⑰ Lock washer
⑱ Connection stud
⑲ Coupling cross adapter
⑳ Adapter lip
Fig. 71: Busbars for busbar current 1600, 2000 and 2500 A

Installation
Busbar lengths With the help of the following table, the required busbar lengths between two adjacent
panels each can be determined by means of the panel width and the arrangement of the
bushings at the vessel.
INFORMATION
If a dummy panel is installed between the switchgear panels, a busbar that is longer by the
width of a dummy panel must be mounted (+300 mm or +600 mm).
Left-hand panel Right-hand panel

Busbar lengths
Depending on the panel
type and panel width
LS, TS, TR,

RK, VS, ME,
LS LK LS, TS LK EB-T aME
EK, QK,
LKLS, LSTS
① L4 ① L4
LS ① L5 ① L5 ① L5 ① L15 ① L8
③ L1 ③ L1
LS, TS, TR,

RK, VS, ME,
① L7 ① L7
EK, QK, ① L10 ① L10 ① L10 ① L16 ① L14
LKLS, LKTS ③ L1 ③ L1
① L2
LK ① L3 ① L3 --- --- ① L11 ① L6
③ L1
① L1 ① L1
LS ① L1 ① L1 ① L1 ① L1
② L12 ② L12 ---
TS ② L13 ② L13 ② L13 ② L17
③ L1 ③ L1
① L1
① L1 ① L1 ① L1
LK --- ② L1 --- ---
② L2 ② L2 ② L9
③ L1
① L7 ① L7
EB-T ① L10 ① L10 ① L10 --- ① L14
③ L1 ③ L1
aME ① L6 ① L6 ① L6 --- --- --- ---
Busbar L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15 L16 L17

Length [mm] 236 281 326 391 436 456 541 566 581 586 626 636 681 716 736 886 981
Reference 250+2 295+2 340+2 405+2 450+2 470+2 555+2 580+2 595+2 600+2 640+2 650+2 695+2 730+2 750+2 900+2 995+2
dimension K1
[mm]
LS Circuit-breaker panel ME Metering panel EB-T Auxiliary transformer panel

TS Disconnector panel EK Incoming sectionalizer aME Air-insulated metering panel
LK Bus sectionalizer QK Bus coupler LKLS Bus sectionalizer/circuit-breaker panel
TR Switch-disconnector panel RK Ring-main panel LKTS Bus sectionalizer/disconnector panel
VS Vacuum contactor panel

Installation
Assembling the 1250 A busbar
Preparing busbar ➭ Check all supplied busbar elements for completeness, cleanliness and proper condition.
elements ➭ Apply mounting paste to the brushed copper surfaces evenly and over the whole surface.
➭ Screw the threaded stud M12/M16 ⑪ into the bushing with a screwdriver size 10x1.6 with
approx. 10 Nm (hand-tight). Important: Check reference dimension (79++2/-6 mm).
➭ Brush oxidized copper surfaces (busbar ends and bushings).

➭ Clean the push-on surfaces of the busbars (gray surfaces), cast-resin cones and outside
cones of the bushings with a lint-free wiping cloth and mounting paste.
INFORMATION
➭ Do not apply mounting paste to the push-on surfaces until right before assembly.
➭ Distribute the mounting paste evenly over the surfaces.
➭ Apply mounting paste to the lower and lateral push-on surfaces of the end adapters ⑤ and
cross adapters ⑩ .
➭ Apply mounting paste to the push-on surfaces (gray surfaces) of the busbars ③ .
➭ Lay the contact half-shells ③ on the ends of the busbar ② and hold them.

Installation
➭ In case of end adapters, add the adjustment component ④ to obtain a symmetrical

clamping.
➭ Push the end adapter ⑤ or cross adapter ⑩ onto the end of the busbar.
➭ If no busbar current transformers are mounted, perform the same assembly operations on
the other end of the busbar.
➭ Remove residual mounting paste.
✔ The busbar unit is assembled.
Mounting the current In switchgear with a busbar current of 1250 A, the current transformers are pre-assembled at
transformers the factory.
Current transformers not pre-assembled at the factory:
• Switchgear with a busbar current ≤ 1600 A
• Air-insulated metering panel
➭ If required, install the current transformers together with the busbar, see page 124,
"Installing current transformers on the busbar"
Pre-assembled current In case of pre-assembled current transformers, the bolted joint of the clamping bracket must
transformers be undone before mounting the busbar units. If required, pull the current transformer out of
the clamping bracket.
① Bolted joint of clamping bracket

② Current transformer
Fig. 72: Pre-assembled current transformers at

the busbar (1250 A)
➭ Push the busbar unit through the current transformer (observe the direction of side P1 at
the current transformer).
➭ Connect the busbar unit with the next end adapter or cross adapter.
➭ After mounting the busbar unit, mount the current transformer again.

Installation
Mounting the busbar run

NOTICE
Pollution through abrasion
Can lead to flashovers and damage the switchgear.
Abrasion can be produced by canting of the busbar units when pushing them onto the
bushings.
➭ Do not cant busbar units.
➭ Push busbar units carefully and slowly onto the bushings.
NOTICE
Damage to the end adapters or cross adapters caused by the threaded stud
Can lead to flashovers and damage the switchgear.
➭ Avoid touching the threaded stud while pushing on the end adapters or cross adapters.
➭ Apply mounting paste to the bushing.
➭ Plug the busbar section loosely over the threaded studs on the bushings of the first two
panels.
➭ Insert another busbar section into the first busbar section.
➭ Insert further busbar sections until the complete busbar run is loosely plugged on the
bushings.

Installation
➭ Press the busbar run onto the bushing.
Bolting the busbar run together

Depending on the type of busbar and the busbar level, the busbar run must be bolted
together differently.
Busbar level Busbar
1250 A 1600/2000/2500 A 2500 A (bus sectionalizer)

1 Version A Version B Version B
2 — Version A Version B
3 — — Version A
Fig. 73: Version A Fig. 74: Version B
➭ Version A: Bolt the threaded stud ⑪ together with the conical spring washer ⑫ (camber
upwards) and the hexagon nut M12 ⑬ (tightening torque: 50 Nm).
➭ Version B: Bolt the threaded stud ⑪ together with the tin-plated copper washer ⑯ , the lock
washer ⑰ and the hexagon nut M12 ⑬ (tightening torque: 50 Nm).
Inserting the ➭ Apply mounting paste to the screw-type cone ⑭ and the upper push-on surface of the cross
screw-type cone adapter or end adapter.

Installation
CAUTION
Disruptive discharges due to air inclusions
Damage to the busbar insulation.
➭ Let excess air out of the screw-type cone with a cable strap while screwing in.
➭ Verify intact condition of the cable strap. If the cable strap was damaged when it was
pulled out, remove the screw-type cone and eliminate the residues of the cable strap.
Let excess air out of the screw-type cone with a cable strap while inserting:
➭ Tighten the screw-type cone ⑭ . Pull out the cable strap ⑳ slowly at the same time.
➭ Check whether the cable strap is complete.
➭ To distribute the mounting paste, turn the screw-type cone back a quarter turn.
➭ Tighten the screw-type cone ⑭ with 30 Nm.
➭ Mount the cap ① .
Final work ➭ Mount the earthing cables of the adapters to the switchgear.
Earthing connection for circuit-breaker Earthing connection for all other panel types
panel (450 mm) and auxiliary transformer panel
Fig. 75: Earthing connection with bolts Fig. 76: Earthing connection at welded stud
① Earthing connection point at the panel ② Earthing connection point at the adapter
➭ Connect all other panels and phases in the same way.

➭ Verify that all unused capacitive taps are earthed.
➭ Mount the busbar support (only for 31.5 kA, see page 122, "Mounting the busbar support").
➭ Install the voltage transformers (option, see page 127, "Installing busbar voltage
transformers").

Installation
➭ Install the low-voltage compartments (see page 133, "Installing the low-voltage
compartment").
➭ Mount the busbar covers (see page 144, "Mounting the busbar covers").
✔ The installation of the busbar is completed.
Mounting the second busbar level for the 1600/2000/2500 A busbar

For the 1600/2000/2500 A busbar, a second busbar level must be mounted. For this purpose,
mount additional coupling cross adapters and coupling end adapters.
First busbar level ➭ Mount the first busbar level without screw-type cones and caps, see page 115, "Assembling
the 1250 A busbar".
Second busbar level ➭ Clean the upper push-on surface of the cross adapter or end adapter, and apply mounting
paste evenly.
➭ Screw the connection stud ⑱ onto the threaded stud ⑪ of the first busbar level (tightening
torque: 50 Nm; insert the hexagon socket spanner fully in the connection stud).
➭ Screw the threaded stud ⑪ into the connection stud as far as it will go (tightening torque:
10 Nm). Important: Check reference dimension 79 +2/-6 mm.
➭ Mount the busbar units including coupling cross adapters, coupling end adapters and
busbars in the same way as for the first busbar level.
NOTICE
Flashovers at the coupling adapters
The adapter lip must not get out of place or caught. The adapter lip of the coupling adapters
must be in line with the adapters of the first busbar level without any gaps.
➭ Check the seating of the adapter lip and adjust, if required.
➭ Push the busbar units on the adapters of the first busbar level.

Installation
Fig. 77: Push the busbar units onto the adapters of the first busbar level
⑳ Adapter lip
Final work ➭ Bolt the busbar run together, see page 118, "Bolting the busbar run together".
Mounting the third busbar level for the 2500 A busbar (bus sectionalizer panel)
For the 2500 A busbar (bus sectionalizer panel), a third busbar level must be mounted.
The third busbar level is limited by the coupling cross adapters on the second busbar level. The
third busbar level does not extend into an adjacent panel.
First and second busbar ➭ Mount the first and second busbar level (see page 120, "Mounting the second busbar level
level for the 1600/2000/2500 A busbar"). Do not mount screw-type cones and caps on the
adapters of the bus sectionalizer panel.
Third busbar level ➭ Mount the coupling adapters of the third busbar level analogously to the second busbar
level, see page 120, "Mounting the second busbar level for the 1600/2000/2500 A busbar".
Fig. 78: Mounting the third busbar level (bus sectionalizer panel 2500 A)

Installation
15.5 Mounting the busbar support
Busbar 1250 A Mount the busbar support:

• On panels of 31.5 kA design
• On panels with a busbar length > 700 mm.
Do not mount the busbar support:
• On panels with busbar current transformers
Circuit-breaker panel (450 mm) and auxiliary transformer panel
Fig. 79: Busbar support in the auxiliary transformer panel

All other panel types
Fig. 80: Busbar support 1250 A

① Busbar support
② Earthing connection at the busbar support
③ Earthing connection of switchgear vessel (welded stud)
④ Earthing connection at the transformer mounting plate (with bolts)
Busbar 1600 A, Mount the busbar support:

2000 A, 2500 A • On all panels of 31.5 kA design
• Mount the busbar support at the upper busbar level according to the enclosed installation
instructions
Do not mount the busbar support:
• On bus sectionalizer panels
• On right-hand end panels
• On panels with busbar current transformers

Installation
① Busbar support
② Earthing connection point at
the busbar support
③ Earthing connection point at
the switching-device vessel
Fig. 81: Busbar support for 1600 A, 2000 A, 2500 A with

earthing connection points
Mounting the busbar support

➭ Mount the busbar support centrally on the busbars.
① Hexagon head bolt M10x75

② Conical spring washer
③ Washer
④ Cable clamp (upper part)
⑤ Distance sleeve
⑥ Cable clamp (lower part)
⑦ Support
⑧ Earthing connection point
Fig. 82: Mounting the busbar support
➭ Mount the earthing cable at the earthing connections of the busbar support and the
switchgear vessel or transformer mounting plate.

Installation
15.6 Installi ng current transformers on the busbar
Installation on 1250 A ➭ Fasten the retainer on the transformer mounting plate using 4 bolts.
busbar ➭ Insert 2 clamping brackets in the openings of the retainer.
➭ Set the current transformers down onto the retainer. Bolt both clamping brackets together
at the top.
① Hexagon nut M8 (2x)

② Flat washer 8 (2x)
③ Bolt M8x35
④ Current transformer
⑤ Clamping bracket (2x)
⑥ Bolt (4x)
⑦ Retainer
Fig. 83: Installing the current transformers (busbar current 1250 A)
Wire routing ➭ Air-insulated metering panel only: Lead the connecting wires of the current transformers
laterally into the operating mechanism compartment and into the low-voltage
compartment through the right wiring duct.
① Vertical wiring duct (only for

connecting wires with steel tube)
② Low-voltage compartment
③ Right-hand wiring duct
Fig. 84: Wire routing (air-insulated metering panel)

Installation
Installation on For busbars with busbar current ≥ 1600 A, the current transformers are supplied with the
busbar ≥ 1600 A accessories.
Fig. 85: Installed busbar current transformers ( ≥ 1600 A)
➭ Cut the felt strips to size and stick 2 of them at the bottom and 1 of them on top of the
current transformers.
At the bottom At the top
➭ Place the current transformer mounting plate onto the current transformers and tighten the
nuts.
➭ Mount the current transformers on the switchgear together with the current transformer
mounting plate. While installing the current transformers, observe the direction of side P1.

Installation
➭ Mount a supporting plate to stabilize the current transformers, and tighten the nuts.
Wire routing ➭ Lead the secondary leads from the instrument transformers into the low-voltage
compartment, and connect.
① Secondary leads
② Vertical wiring duct
(only for secondary leads with
steel tube)
③ Cutout
Fig. 86: Cable routing into the low-voltage

compartment

Installation
15.7 Installing busbar voltage transformers

The voltage transformers are delivered separately. For installation, the busbars must be
mounted and accessible from the front. If required, remove any mounted low-voltage
compartments.
INFORMATION
For the following panel types, a lower voltage transformer frame (229 mm) must be mounted:
• Circuit-breaker panel (450 mm)
• Auxiliary transformer panel
Fig. 87: Voltage transformers mounted Fig. 88: Voltage transformers with lower voltage
on 1250 A busbar transformer frame
Fig. 89: Voltage transformer mounted on the busbar (view from the front)
① Voltage transformer ⑧ Centering nut (tightening torque: 10 Nm)

② Storage box ⑨ Hexagon nut M12* (tightening torque: 50 Nm)
③ Voltage transformer frame ⑩ Conical spring washer *
④ Nut-and-washer assembly M8 / bolt M6 with ⑪ Contact half-shell *
plain washer1
⑤ Plain washer (DIN EN ISO 7093-1-8) ⑫ Threaded stud M12/M16 (tightening torque: 10 Nm)*
⑥ Bolt-and-washer assembly M8x20 ⑬ End adapter/cross adapter
⑦ Cast-resin cone of voltage transformer * Component pre-assembled at the end adapter/cross
adapter
1 For panel types LS 450 mm and auxiliary transformer panel

Installation
INFORMATION
To mount the voltage transformer on the busbar, the caps and screw-type cones of the busbar
are not required.
➭ Mount the busbar according to the installation instructions (see page 111, "Assembling the
busbars"); do not mount caps and screw-type cones.
➭ If the busbar is already mounted, remove the caps and screw-type cones again.
➭ Put unneeded components into the storage box.
➭ Remove the cap and the screw-type cone of end adapter / cross adapter.
➭ Screw the centering nut ⑧ onto the threaded stud ⑫ in the end adapter / cross adapter
(tightening torque: 10 Nm).
Fig. 90: Removing the cap and the Fig. 91: Screwing on the centering
screw-type cone nut
➭ Set the voltage transformer frame ③ down on the switchgear with the protrusion aligned
to the left.
- Circuit-breaker panel of 450 mm and auxiliary transformer panel: The holes in the
frame feet must match with the holes of the switchgear.
- Other panel types: The threaded studs on the switchgear vessel must fit into the holes of
the frame feet.
➭ Depending on the panel type, fasten the voltage transformer frame ③ using nut-and-
washer assemblies or bolts ④ .

Installation
Installing the voltage transformers
DANGER
Hazardous voltage
Can cause death, injury or considerable property damage.
The metal coating on the outside of voltage transformers is connected to earth potential. If the
metal coating is damaged, the voltage transformer is not safe-to-touch anymore.
➭ Do not damage the metal coating of voltage transformers.
NOTICE
Flashovers in the adapter due air inclusions
Insufficient busbar insulation can damage the switchgear.
➭ While installing the voltage transformer, let excess air out of the adapter with a cable strap.
➭ Verify intact condition of the cable strap. If the cable strap was damaged when it was
pulled out, remove the voltage transformer and eliminate the residues of the cable strap.
INFORMATION
To be able to close the busbar in a surge-proof way again, e.g. to remove a defective voltage
transformer, keep the following objects in the storage box after installation:
• Remaining screw-type cones and caps
• Residual mounting paste (tube)
• Cable strap
INFORMATION
Recommended installation order for voltage transformers:
➭ In order to better reach the bolted joints, install the voltage transformers on phases L1 and
L3 first, and then the voltage transformer on phase L2.
INFORMATION
During installation, protect the voltage transformer bushings from damage.
➭ Plug the removed protective caps of the vessel bushings onto the voltage transformer
bushings.
Fig. 92: Protective cap
➭ Apply mounting paste to the high-quality joints of the voltage transformer and the end
adapter / cross adapter before mounting.
➭ While mounting the voltage transformer, let excess air out of the end adapter / cross adapter
with a cable strap ⑮ .

Installation
Fig. 93: Setting down the voltage transformer
➭ Set the voltage transformer ① down on the voltage transformer frame. The cast-resin cone
of the voltage transformer must penetrate into the end adapter / cross adapter.
While doing so, pull the cable strap ⑮ slowly out of the end adapter / cross adapter, and
verify intact condition.
If parts of the cable strap are missing, remove the voltage transformer again and verify that
no residuals of the cable strap remain in the end adapter / cross adapter.
➭ The voltage transformer must be correctly seated on its bolted joints.
➭ Fasten the 3 voltage transformers with 4 bolt-and-washer assemblies ⑥ and washers ⑤

each (tightening torque: 20 Nm).
Fig. 94: Bolted joints of voltage transformers

⑤ Plain washer (DIN EN ISO 7093-1-8)
⑥ Bolt-and-washer assembly M8x20
Connecting secondary Secondary leads are not pre-assembled on all voltage transformer types.
leads
➭ Connect the secondary leads that have been supplied separately to the voltage transformer.
Observe the phase sequence!
Fig. 95: Connecting secondary leads

Installation
➭ Lead the secondary leads of the instrument transformers into the low-voltage
compartment, and connect them.
Observe the phase sequence!
① Secondary leads
② Vertical wiring duct
(only for secondary leads with
steel tube)
③ Cutout
Fig. 96: Cable routing into the low-voltage compartment
➭ Connect the earthing cable of the end adapters/cross adapters.
Checking the voltage

transformer connection
① Voltage transformer
② Plug connector
③ Busbar
④ Three-position switch
⑤ Circuit-breaker
⑥ Battery box (15 – 20 V)
Fig. 97: Circuit diagram for checking

the voltage transformer
connection
➭ On one panel of the switchgear, switch the circuit-breaker and the three-position switch to
CLOSED position.
➭ Connect a voltmeter to the outgoing cable of the voltage transformer and set the mV-range.
➭ Apply 15 to 20 V DC to L1, L2, L3 to earth with the battery and observe the voltmeter.
✔ If the pointer moves a little bit, the voltage transformer connection is in good order.

Installation
15.8 Interconnecting the earthing busbars
① Earthing connection point

② Link
③ Earthing busbar
Fig. 98: Interconnecting the earthing busbars
➭ Auxiliary transformer panel only: The link for an earthing busbar connection to the left is
located in the lateral cable compartment. To connect the earthing busbar, remove the metal
cover of the lateral cable compartment.
➭ Detach the pre-assembled link provided at the joint, and push it through the opening of the
side wall.
➭ Brush oxidized copper surfaces and apply a thin film of mounting paste.
➭ Bolt the link together with the adjacent unit of the earthing busbar (tightening torque:
50 Nm).
➭ Proceed in the same way with the other joints.
15.9 Switchgear earthing

The cross-sections and materials of the earthing conductors are specified in the DIN/VDE 0101
(IEC 61936-1) standard or in the relevant country-specific standards.
The diameter of the earthing cable must be at least 70 mm 2.
NOTICE
Use of incorrect earthing connection point
Can cause property damage. The earthing connection point for earthing accessories is
not dimensioned for the earthing at the substation earth.
➭ Connect the switchgear to the substation earth exclusively at the earthing connection
points appropriate for this purpose.
➭ Connect the earthing busbar of the two end panels to the substation earthing system
through one of the earthing connection points ① (bolt M12). In addition, earth every fifth
panel.
➭ Lay the earthing cable ② through the left-hand wiring duct ③ into the cable basement.
➭ Connect the earthing cable to the substation earth.

Installation
① Earthing connection
point
② Earthing cable
③ Left-hand wiring duct
④ Earthing connection
point extended to the
front for earthing
accessories (do not use)
Fig. 99: Earthing the switchgear (example)
15.10 Installing the low-voltage compartment

➭ Place the low-voltage compartment onto the frame of the associated panel and push it to
the rear.
The 2 lugs ① at the rear of the low-voltage compartment must be pushed into the cutouts
at the panel. The front of the low-voltage compartment must be in line with the panel front.
➭ Fasten the low-voltage compartment to the frame at 2 positions at the bottom by means of
the bolted joint ② .
➭ Mount all other low-voltage compartments in the same way.
➭ Join each low-voltage compartment with the adjacent low-voltage compartment at
3 positions on the right by means of the bolted joint ③ .
➭ Thread the prefabricated cables of the switching devices through the right-hand opening at
the bottom of the low-voltage compartment.
➭ Connect the 2-pole, 4-pole and 10-pole plugs with the corresponding terminals according to
the circuit diagram (see page 169, "Connecting the STG plug with the VBSTB4 modular
terminal").
➭ Lay the bus wires in wiring ducts and connect them with the corresponding terminals
according to the circuit diagram.
➭ Connect the wires of the current transformers and voltage transformers with the
corresponding terminals according to the circuit diagram.
① Lugs
② Lower bolted joint:
• Locknut M8
• Contact washer 8
• Bolt-and-washer
assembly M8
③ Lateral bolted joint:
• Self-tapping oval head
bolt M5
• Contact washer 5
Fig. 100: Bolting the low-voltage compartment together

Installation
15.11 Installing the horizontal pressure relief duct
INFORMATION
If a horizontal pressure relief duct is installed, the busbar cover is not assembled.
➭ Install the switchgear termination, see page 143, "Installing the switchgear termination".
➭ Install the horizontal pressure relief duct.
Panel versions with horizontal pressure relief duct
Design option Panel Busbar current depending on the panel position1

width
Left end panel Intermediate Right end panel
[mm]
panel
Standard (without 600/450 - ≤ 1250 A -
ventilation)
With ventilation 600/450 ≤ 1250 A - ≤ 1250 A
2000 A 2000 A 2000 A
900
2500 A 2500 A 2500 A
Evacuation at the rear 600/450 - ≤ 1250 A2 -
1
Independently from the panel position, the panel types LS/LLK(2000 A/2500 A), EB
and aME are always equipped with ventilation.
2
Only for a panel width of 600 mm.
Modular design
The evacuation duct can be set up with modular elements from the switchgear up to the
opening in the substation wall.
The individual elements can be combined at will in order to build an evacuation duct matching
with the switchgear arrangement situation in the substation.
Fig. 101: Possible combinations of evacuation duct elements
Duct elements
Duct element Duct element
Designation Length Designation Length

Evacuation duct 1000 mm 1000 mm Evacuation duct 900 mm 900 mm
Evacuation duct 600 mm 600 mm Evacuation duct 500 mm 500 mm
Evacuation duct 450 mm 450 mm Evacuation duct, adjustable 520 to

685 mm

Installation
Duct element Duct element
Designation Length Designation Length
Evacuation duct, flap, exit 480 mm Evacuation duct termination, expanded 260 mm
metal
Angle
Type designation Angle Dimensions

Evacuation duct angle, vertical 45°
Evacuation duct angle, horizontal 45°
Supports
Type designation Illustration

Fixing lugs for evacuation duct
Fixing bracket, evacuation duct

Installation
Bolting material
Designation Size Illustration

Bolt-and-washer assembly M8
Setnut M8
Duct elements on the switchgear

For installation of the horizontal pressure relief duct on the switchgear, the following
elements are required. Here, the elements for a panel width of 600 mm are shown as an
example.
Designation Detailed designation Illustration

Side plate Connecting element, lateral
evacuation, left side (with pre-
assembled evacuation duct
element)
Side plate Connecting element, lateral

evacuation, right side (with pre-
element)
Rear wall Connecting element, rear

evacuation, (with pre-
element)
Rear wall Rear wall, closed
Top cover Top cover with ventilation

Installation
Designation Detailed designation Illustration

Top cover Top cover, closed
Front plate Front plate, closed
Side plate Side plate, closed, left side
Side plate Side plate, closed, right side
Mounting the side plates

Before the horizontal pressure relief duct can be installed, the switchgear termination must be
mounted (see page 143, "Installing the switchgear termination").
Perform the installation from the front, starting with the left end panel.
Installation with lateral evacuation to the left is shown here as an example.
INFORMATION
If a higher low-voltage compartment is mounted, it is not possible to install the horizontal
pressure relief duct from the front.
➭ Install from the top or from the side.
Or
➭ Remove the low-voltage compartment and install from the front.

Installation
➭ Place the left-hand side plate ① onto the switchgear termination ③ .
① Side plate
② Pre-assembled
evacuation
③ Switchgear termination
➭ Bolt the side plate together with the switchgear termination using 2 bolts M8x20.
➭ Bolt the side plate laterally together with the rear wall of the low-voltage compartment
using one self-tapping bolt M5 and one washer.
➭ Mount the right-hand side plate on the right end panel.

✔ The side plates of the horizontal pressure relief duct are installed.
INFORMATION
If the installation of the top cover is not possible due to the height of the switchgear room, the
rear wall and top cover must be pre-assembled.
➭ Place the top cover on the rear wall.
➭ Bolt the top cover together with the rear wall using 3 bolts M8, and place it on the
switchgear.

Installation
Mounting the rear walls

The installation of the rear evacuation is identical to the installation of a rear wall. The
installation differs depending on the individual panel type and the panel width.
For panels
• With a panel width of 600 mm Other panel types with a panel width of 900 mm
• With a panel width of 450 mm
• Air-insulated metering panel (aME)
• Auxiliary transformer panel (EB)
➭ Push the rear wall ① on the pre-assembled fixing bracket ② . ➭ Place the rear wall ① on the pressure relief duct ② .
➭ Bolt the rear wall ① together with the side plate ③ or another rear wall using ➭ Bolt the rear wall ① together with the side wall ③ or
3 bolts M8x20 and nut-and-washer assemblies (tightening torque: 20 Nm). another rear wall using 3 bolts M8x20 and nut-and-washer
assemblies (tightening torque: 20 Nm).
➭ Bolt the rear wall ① together with the fixing Number of bolted joints: ➭ Bolt the rear wall together with the rear threaded studs using
bracket ② using bolts M8x20 and nut-and-washer 600 mm panel width: 4x 5 nut-and-washer assemblies.
assemblies (tightening torque: 20 Nm). 450 mm panel width: 3x
aME: 6x
EB = 6x
➭ Mount further rear walls. ➭ Mount further rear walls.
Checking the ventilation flap

Installation
NOTICE
Pollution of the switchgear room
In case of fault, a non-functioning ventilation flap can pollute the switchgear room very
much.
➭ Check smooth operation of the ventilation flap.
➭ Open the ventilation flap after installation.
➭ Open and close the ventilation flap ② at the top cover of the pressure relief duct ① several
times.
✔ If the ventilation flap can be opened and closed easily, then it is ready for assembly.
Installing top covers

To install a top cover, the design option of the top cover is not relevant.
Before installing a top cover with ventilation, the ventilation's operability must have been
tested.
➭ Push the top cover from the front to the rear wall, and place it flush on the side plate and
the rear wall.
➭ Bolt the top cover together with the side plate from the inside to the outside using
3 bolts M8x20 and nut-and-washer assemblies (tightening torque: 20 Nm).
➭ Bolt the top cover together with the rear wall from top to bottom using bolts M8x20 and
nut-and-washer assemblies (tightening torque: 20 Nm).
Bolted joint with side

plate
Number of bolted
joints (rear wall):
Panel width 600 mm:
3x
Panel width 900 mm:
3x
Panel width 450 mm:
2x
aME: 4x
EB: 4x
➭ Mount further top covers.

Installation
Mounting front plates

➭ Place the front plate flush on the top cover, the side plate and the low-voltage
compartment.
➭ Bolt the front plate together with the side plate using 3 bolts M8x20 and nut-and-washer
assemblies.
➭ Bolt the front plate together with the top cover in the upper area using bolts M8x20 and
nut-and-washer assemblies.
➭ Bolt the front plate together with the low-voltage compartment in the lower area using bolt-
and-washer assemblies M8x20.
Bolted joint with side plate
Number of bolted joints:

Panel width 600 mm: 3x
aME: 4x
EB: 4x
➭ Mount further front plates.
Assembling the evacuation duct

In order to mount an evacuation duct matching with the corresponding switchgear
arrangement, the individual duct elements can be combined at will.
In order to guarantee its stability, the evacuation duct must be supported at regular intervals
(recommended value: every 100 cm). Fixing lugs are available for this purpose.
Possible mounting positions of the fixing lugs
Connecting the duct The installation of the duct elements shown here is illustrated as an example with a 500 mm
elements duct element and an adjustable duct element. Mount other duct elements according to the
same principle.

Installation
➭ Push the duct element ② into the joining bracket ③ of the adjustable duct element ① .
➭ Fasten the duct elements at 12 connecting points using bolt-and-washer assemblies M8x20
and washers (tightening torque: 20 Nm).

Installation
15.12 Installing the switchgear termination
INFORMATION
The end panel of the NXPLUS C switchgear is delivered as standard with pre-assembled
switchgear termination and termination angle.
If the customer ordered without pre-assembled switchgear termination and termination
angle, perform the following work operations.
➭ Bolt the switchgear termination together with the front and rear edge of the end panel
using 12 self-tapping bolts size M5 each.
➭ Mount the termination angle at the upper edge of the panel.

➭ In panels without pressure relief duct, press the end cover firmly to the wall and tighten the
bolts. If applicable, fasten to the wall.

Installation
15.13 Mounting the busbar covers
INFORMATION
On panels with a panel width of 900 mm, additional air guides must be mounted after
mounting the busbar covers, see page 151, "Mounting the air guides".
INFORMATION
The components of the busbar cover are delivered with the switchgear accessories and are
marked with a component number. With the following component tables, the component
numbers of the components required for the corresponding panel can be identified.
Fig. 102: Position of the component number (arrow)
INFORMATION
Before mounting the busbar covers, the following information must be at hand for each panel:
• Is the panel equipped with a pressure relief duct (yes or no)
• Is the panel equipped with voltage transformers at the busbar (yes or no)
• Panel width (450 mm, 600 mm or 900 mm)
• Height of low-voltage compartment (760 mm or 1160 mm)
• Degree of protection of the panel (IP3XD, IP31D, IP32D or IP34D, see single-line diagram)
• Busbar current (see single-line diagram)
• Feeder current (see single-line diagram)
• Type of installlation of the switchgear (wall-standing arrangement or free-standing
arrangement)
① Height of low-voltage compartment

② Panel width
③ Pressure relief duct
④ Voltage transformers at the busbar
⑤ Busbar cover
Preconditions • Panels are mounted and bolted together.

• Panels are fastened to the foundation.
• Voltage transformers (option) are mounted at the busbar.
• Identify the busbar cover components to be mounted for the individual panel using the
corresponding component table:

Installation
Degree of Busbar current Voltage transformers Voltage transformers at the busbar in Component table
protection at the busbar the right-hand adjacent panel
up to 1250 A not relevant see page 146, "Component table 1"
yes
1600 A yes
IP3XD no see page 148, "Component table 3"
2000 A
yes
2500 A no
no see page 146, "Component table 1"
up to 1250 A not relevant see page 146, "Component table 2"
IP31D yes
1600 A yes
IP32D no see page 148, "Component table 4"
2000 A
IP34D yes
2500 A no
no see page 146, "Component table 2"

Installation
Component table 1
Panel Components
Sealing angle2
Reinforcing plate1
Termination angle
panel width [mm]
Supporting angle
Feeder current
Pressure relief
compartment
Panel type or
low-voltage
Wall- Free-
Height of
Cover
standing standing
[A]
arrangement arrangement
Number in exemplary illustration: ① ② ③ ④ ⑤ ⑥ ⑤ ⑥

LS not not 760 -- 87 75 -- --
(450 mm) relevant relevant 1160 -- 88 76 -- --
not not 760 -- 89 -- -- --
aME
relevant relevant 1160 -- 90 -- -- --
not not 760 -- 89 75 77 --
EB-T
relevant relevant 1160 -- 90 76 78 --
760 -- 3 75 77 --
45/50
1000
1160 -- 46/51 3 76 78 --
yes
760 -- 45/523 75 77 --
1250
1160 -- 3 76 78 --
46/53
600
760 96 47/543 75 -- --
1000
1160 96 48/553 76 -- --
no
760 -- 47/543 75 -- --
1250
1160 -- 49/563 76 -- --
not not 760 -- 71/733 83 77/814 97 98 99 100

900
relevant relevant 1160 -- 72/743 76 80 97 98 99 100
1 Only to be mounted in panels of 31.5 kA design.
2
Only for end panel or if the adjacent panel has a width of 600 mm.
3
Only for bus sectionalizer panel, the cover consists of two components.
4 Only for bus sectionalizer panel.
Component table 2
Panel Components
Sealing angle 2
Reinforcing plate1
Termination angle
panel width [mm]
Supporting angle
Feeder current
Pressure relief
compartment
Panel type or
low-voltage
Wall- Free-
Height of
Cover
standing standing
[A]
arrangement arrangement
Number in exemplary illustration: ① ② ③ ④ ⑤ ⑥ ⑤ ⑥

LS not not 760 -- 87 76 -- --
(450 mm) relevant relevant 1160 -- 87 76 -- --
760 -- 46/513 76 78 --
1000
1160 -- 46/513 76 78 --
yes
760 -- 46/533 76 78 --
1250
1160 -- 46/533 76 78 --
600
760 96 48/553 76 -- --
1000
1160 96 48/553 76 -- --
no
760 -- 49/563 76 -- --
1250
1160 -- 49/563 76 -- --
not not 760 -- 72/743 76 80/824 97 98 99 100

900
relevant relevant 1160 -- 72/743 76 80/824 97 98 99 100
1
Only to be mounted in panels of 31.5 kA design.
2
Only for end panel or if the adjacent panel has a width of 600 mm.
3
Only for bus sectionalizer panel, the cover consists of two components.
4
Only for bus sectionalizer panel.

Installation
Component tables 1 and 2: Examples for busbar covers (view from the rear)
Installation for ➭ Panel without pressure relief: Bolt supporting angles ① together with the rear walls.
component tables 1 and 2
Fig. 103: Mounting the supporting angles (view from above, example)
➭ Bolt the cover ② together with the panel.

➭ The panel is an end panel: Fasten the termination angle ③ .
➭ Panel version 31.5 kA: Bolt the reinforcing plate ④ together with the covers.
➭ Mount the left-hand ⑤ or right-hand sealing angle ⑥ under the following preconditions:
- The panel has a width of 900 mm and is in free-standing arrrangement.
- The adjacent panel has a width of 600 mm.
➭ Repeat the installation of the busbar cover for all panels.
✔ The installation of the busbar cover is completed.

Installation
Component table 3
Switchgear panel Components
Sealing angle4
Supporting angle1
Angle plate
Connection plate2
Reinforcing plate
LV compartment
Pressure relief
Panel width
Side wall3
Widht of left- Width of right- Wall- Free-
Height of
Position
Cover
[mm]
hand adjacent hand adjacent standing standing

panel [mm] panel [mm] arrangement arrangement
600 900 600 900
Number in exemplary illustration: ① ② ③ ④ ⑤ ⑥ ⑥ ⑦ ⑦ ⑧ ⑨ ⑩ ⑨ ⑩

No 96 --- 03 05 24 26 25 27 10 ---
760
Intermedi Yes --- --- 01 05 12 14 13 15 08 ---
ate panel No 96 84 04 06 07 28 30 29 31 11 ---
1160
Yes --- 84 02 06 07 18 20 19 21 09 ---
No 96 --- 03 05 16 25 27 10 ---
760
Left end Yes --- --- 01 05 16 13 15 08 ---
600
panel No 96 84 04 06 07 22 29 31 11 ---
1160
Yes -- 84 02 06 07 22 19 21 09 ---
No 96 --- 03 05 --- 17 --- ---
760
Right end Yes --- --- 01 05 --- 17 --- ---
panel No 96 84 04 06 07 --- 23 --- ---
1160
Yes --- 84 02 06 07 --- 23 --- ---
No --- --- 57 05 41 10 97 98 99 100
760
Intermedi Yes --- --- 57 05 41 08 97 98 99 100
ate panel No --- 85/86 58 39 40 42 11 97 98 99 100
1160
Yes --- 85/86 58 39 40 42 09 97 98 99 100
No --- --- 57 05 41 10 97 --- 99 ---
760
Left end Yes --- --- 57 05 41 08 97 --- 99 ---
900
panel No --- 85/86 58 39 40 42 11 97 --- 99 ---
1160
Yes --- 85/86 58 39 40 42 09 97 --- 99 ---
No --- --- 36 05 --- 43 --- --- 98 --- 100
760
Right end Yes --- --- 36 05 --- 43 --- --- 98 --- 100
panel No --- 85/86 37 39 40 --- 44 --- --- 98 --- 100
1160
Yes --- 85/86 37 39 40 --- 44 --- --- 98 --- 100
1
Only for panel with feeder current ≤ 1000 A.
2
85: For voltage transformers at the busbar in the right-hand adjacent panel.
86: For panel with voltage transformers at the busbar.
3
Mount only one left-hand or right-hand side wall each.
4
Only for left-hand or right-hand adjacent panel with a panel width of 600 mm.
Component table 4
Sealing angle3
Supporting angle1
Angle plate
Reinforcing plate
LV compartment
Pressure relief
Panel width
Side wall2
Widht of left- Width of right- Type of installation of

Height of
Position
Angle
Cover
[mm]
hand adjacent hand adjacent the switchgear

panel [mm] panel [mm]
600 900 600 900 Wall Free
Number in exemplary illustration: ① ③ ④ ⑤ ⑥ ⑥ ⑦ ⑦ ⑧ ⑨ ⑩ ⑨ ⑩ ⑪

Intermedi No 96 124 05 108 110 114 116 10 --- 125
ate panel Yes --- 101 05 109 112 115 117 106 --- 125
Left end No 96 124 05 113 114 116 10 --- 125
600 760
panel Yes --- 101 05 113 115 117 106 --- 125
Right end No 96 124 05 --- 118 --- --- 125
panel Yes --- 101 05 --- 118 --- --- 125

Installation
Sealing angle3
Supporting angle1
Angle plate
Reinforcing plate
LV compartment
Pressure relief
Panel width
Side wall2
Widht of left- Width of right- Type of installation of
Height of
Position
Angle
Cover
[mm]
hand adjacent hand adjacent the switchgear

panel [mm] panel [mm]
600 900 600 900 Wall Free
Number in exemplary illustration: ① ③ ④ ⑤ ⑥ ⑥ ⑦ ⑦ ⑧ ⑨ ⑩ ⑨ ⑩ ⑪

Intermedi No --- 102 05 111 106 97 98 99 100 126
ate panel Yes --- 102 05 111 106 97 98 99 100 126
Left end No --- 102 05 111 106 97 --- 99 --- 126
900 760
panel Yes --- 102 05 111 106 97 --- 99 --- 126
Right end No --- 103 05 --- 119 --- --- 98 --- 100
127
panel Yes --- 103 05 --- 119 --- --- 98 --- 100
1
Only for panels with feeder current ≤ 1000 A.
2
Mount only one left-hand or right-hand side wall each.
3
Only for left-hand or right-hand adjacent panel with a panel width of 600 mm.
Component tables 3 and 4: Examples for busbar covers (view from the rear)

Installation
Installation for ➭ Panel without pressure relief: Bolt supporting angles ① together with the rear walls.
component tables 3 and 4
Fig. 104: Mounting the supporting angles (view from above, example)
➭ Panel with 1160 mm high low-voltage compartment: Bolt the connection plate ②
together with the rear wall of the low-voltage compartment. Bolt the connection plate ②
together with the connection plate of the adjacent panel.
Fig. 105: Mounting the connection plate (view from the rear, example)
➭ Bolt the left-hand ④ or right-hand side wall ⑤ together with the cover ③ .
➭ Panel with degree of protection IP3XD, IP31D, IP32D or IP34D: Fasten the termination
angle ⑪ .
➭ Bolt the cover ② together with the panel.
➭ Mount the left-hand ⑥ or right-hand angle plate ⑦ .
➭ Mount the reinforcing plate ⑧ onto the covers mounted before.
➭ Mount the left-hand ⑨ or right-hand sealing angle ⑩ under the following preconditions:
- The panel has a width of 900 mm and is in free-standing arrrangement.
- The adjacent panel has a width of 600 mm.
➭ Repeat the installation of the busbar cover for all panels.
✔ The installation of the busbar cover is completed.

Installation
15.14 Mounting the air guides
WARNING
Pressure wave, intense heat or escaping gases
Can cause serious injury or property damage.
On panels with a panel width of 900 mm, air guides must be mounted. Without air guides, the
internal arc classification of the switchgear is not guaranteed.
➭ Mount the air guides.
INFORMATION
The components of the air guides are delivered with the switchgear accessories and are marked
with a component number. With the following component tables, the numbers of the
components required for the corresponding panel can be identified.
Fig. 106: Position of the component number (arrow)
INFORMATION
Before mounting the air guides, the following information must be at hand for each panel:
• Is the panel equipped with voltage transformers at the busbar (yes or no)
• Height of low-voltage compartment (760 mm or 1160 mm)
• Degree of protection of the panel (IP3XD, IP31D, IP32D or IP34D, see single-line diagram)
• Type of installation of the switchgear (wall-standing arrangement or free-standing
arrangement)
Preconditions • The busbar cover is mounted.

• Identify the air guide components to be mounted in the corresponding panel using one of
the component tables. The component table to use depends on the degree of protection of
the panel.
Degree of protection Component table

IP3XD see page 152, "Component table
1"
IP31D, IP32D or IP34D see page 152, "Component table
1"

Installation
Component table 1
Panel Component number
compartment [mm]
Voltage transformers at the
Type of installation
busbar
low-voltage
Panel width
Height of
Position
[mm]
Present panel Right-hand

Front air guide Rear air guide Side wall Rear wall
adjacent
panel
Number in exemplary illustration: ① ② ③ ④

Free 60 65 66 70
yes
Wall 60 65 66 ---
760 no
Left end Free 62 65 66 70
no
panel Wall 62 65 66 ---
Free --- 65 67 70
1160 not relevant
Wall --- 65 67 ---
Free 64 65 --- 70
yes no
Wall 64 65 --- ---
Free 60 65 --- 70
900 760 yes
Intermedi Wall 60 65 --- ---
no
ate panel Free 62 65 --- 70
no
Wall 62 65 --- ---
Free --- 65 --- 70
1160 not relevant
Wall --- 65 --- ---
Free 62 65 68 70
760 no no
Right end Wall 62 65 68 ---
panel Free --- 65 69 70
1160 not relevant
Wall --- 65 69 ---
Component table 2
Panel Components
compartment [mm]
Voltage transformers at the

Type of installation
busbar
Panel width
low-voltage
Height of
Position
[mm]
Present panel Right-hand

Front air guide Rear air guide Side wall Rear wall
adjacent
panel
Number in exemplary illustration: ① ② ③ ④

Free 61 65 66 70
yes
Wall 61 65 66 ---
760 no
Left end Free 63 65 66 70
no
panel Wall 63 65 66 ---
Free --- 65 67 70
1160 not relevant
Wall --- 65 67 ---
Free 62 65 --- 70
yes no
Wall 62 65 --- ---
Free 61 65 --- 70
900 760 yes
Intermedi Wall 61 65 --- ---
no
ate panel Free 63 65 --- 70
no
Wall 63 65 --- ---
Free --- 65 --- 70
1160 not relevant
Wall --- 65 --- ---
Free 63 65 68 70
760 no no
Right end Wall 63 65 68 ---
panel Free --- 65 69 70
1160 not relevant
Wall --- 65 69 ---

Installation
Component tables 1 and 2: Examples for air guides
Mounting the air guides ➭ Panel with lower low-voltage compartment: Mount the front air guide ① .
➭ Panel in free-standing arrangement: Mount the rear wall ④ at the rear air guide ③ .
➭ Mount the rear air guide ③ .
➭ End panel: Mount the left-hand or right-hand side wall ② .

Installation
15.15 Extension with individual panels

Do always observe the Five Safety Rules if you are going to extend an existing switchgear
assembly or replace components:
DANGER
Hazardous voltage.
➭ Isolate.
➭ Remove the switchgear termination.

➭ Remove the low-voltage compartment, the busbar cover and, if required, the current or
voltage transformers of the last panel and the one before last.
➭ Approach the extension panel, align it and bolt it together (see page 108, "Aligning and
joining the panels").
➭ Fasten the extension panel to the foundation (see page 110, "Fastening the panel to the
foundation").
➭ On the last two panels, remove the cap and the screw-type cone of the busbar.
➭ Undo M12 nut and take it out.
➭ Remove the conical spring washer (do not use it again).
➭ For further installation, see page 111, "Assembling the busbars".
➭ Replace the end adapters of the former end panel by cross adapters.
➭ Grease new components with mounting paste.
➭ Do not forget to let excess air out (see page 118, "Bolting the busbar run together").
16 Electrical connections
In the instructions given in the following sections it is assumed that a new switchgear is being
installed which has not yet been connected to the mains, and is not live.
For extending or replacing parts of an existing switchgear, the Five Safety Rules must be
observed:
DANGER
Hazardous voltage.
➭ Isolate.

Installation
16.1 Installation work at the floor cover

The floor cover is pre-assembled at the factory. Before starting with the installation of cable T-
plugs, the floor cover must be removed. The floor cover is installed in the course of the
installation of the cable T-plugs.
Removing the floor cover
① Nut-and-washer
assembly
② Front floor plate
③ Bolts
④ Floor plates
⑤ Rubber sleeves
Fig. 107: Removing the floor cover (example: panel width 600 mm)
Fig. 108: Removing the floor cover (example: panel width 900 mm)
➭ Undo 2 nut-and-washer assemblies ① and the 4 bolts ③ of the front floor plate ② .
➭ Lift the front floor plate ② and pull it out.
➭ Remove all other floor plates ④ : Undo 4 bolts each and pull out the floor plate. Then pull
out the rubber sleeves ⑤ to the front.
✔ The panel is ready for connecting the cable T-plugs.

Installation
Cutting the rubber sleeves to size
INFORMATION
The rings in the rubber sleeves are not adjusted to the cable diameters, but serve only as rough
orientation.
➭ With a knife, cut an opening into the rubber sleeve that fits the diameter of the cable.
Fig. 109: Cutting the rubber sleeves to size
Mounting the floor plates

➭ Push the rubber sleeve onto the cable T-plug.
➭ Connect the cable T-plug (see page 158, "Connecting cable T-plugs").
➭ Insert the rubber sleeve into the recess of the floor plate.
Fig. 110: Example for panel width 900 mm

Installation
➭ Insert the next floor plate in the notch of the rubber sleeve.
➭ Bolt the floor plate tight.
➭ Mount further floor plates.
Mounting the termination ➭ Push the termination plate under the last floor plate and set it on the studs.
plate
➭ Bolt the floor plate and the termination plate together using 4 bolts and washers.

Installation
➭ Screw nut-and-washer assemblies onto the studs.
16.2 Connecting cable T-plugs

For NXPLUS C switchgear, only cable T-plugs shielded by means of an external semi-
conductive layer may be used as a rule. The suitable cable plugs for outside-cone bushings of
interface type C according to EN 50181 are listed in the section "Description" (see page 34,
"Cable connection"NXPLUS C).
Please select the tightening torque of the bolted joint "cable T-plug - bushing" according to the
specifications of the respective cable T-plug manufacturer.
If there are no specifications from the cable T-plug manufacturer's side, please tighten the
bolted joint with 50 Nm.
Phase sequence
Fig. 116: Phase sequence of bushings in the cable compartment
Preparations ➭ Earth the feeder.

➭ Undo the fixing bolts of the cable compartment cover.
➭ Lift the cable compartment cover and remove it to the front.
➭ Remove the floor cover (see page 155, "Removing the floor cover").
➭ Cut rubber sleeves to size (see page 156, "Cutting the rubber sleeves to size").
Mounting cable T-plugs

on cable ends DANGER
Life-endangering high voltage
Will cause death, serious injury or considerable property damage.
Do not energize the switchgear as long as no cables or surge-proof caps are mounted.
➭ If the panel has to be live without connected cables, close the outside-cone bushings in a
surge-proof way.
➭ Mount surge-proof caps onto bushings type C (with bolted contact M16).

Installation
NOTICE
Flashovers due to insufficient electrical contact, abrasion or pollution of the push-on
surfaces (high-quality joints)
Will cause damage to the bushings in operation.
➭ All assembly work at the bushings must be carried out with particular care. Avoid
damaging the contact surfaces and the silicone surfaces.
➭ Avoid damage caused by the threaded stud while pushing on.
➭ Observe extreme cleanliness.
➭ No smoking.
NOTICE
Inappropriate installation of the plug sets
Damage to the plug sets due to thermal overloading.
If the electrical contact of the surfaces of the high-quality joints is insufficient, the plug sets can
overheat.
➭ The cable T-plugs must only be mounted by instructed personnel.
➭ Do not mount cable plugs in bent or twisted manner.
NOTICE
Removed protection ring
Will cause damages at the connection of the capacitive voltage detecting system.
A white plastic protection ring may be factory-assembled on the outside-cone bushing type C.
The protection ring serves as a stop for the plug, and protects the connection of the capacitive
voltage detecting system from damages when the cable plugs are mounted.
➭ Do not remove the protection ring.
Fig. 117: Protection ring
➭ Push the rubber sleeve onto the cable.

➭ Fit the cable T-plugs on the cable ends according to the manufacturer’s instructions.
➭ Mount the cable T-plugs one after the other on the phases L1 to L3 according to the
manufacturer’s instructions.
NOTE: A too high torque can cause damage to the bushing. Tighten the cable plug
with a torque according to the manufacturer's instructions (max. 50 Nm).
Mounting the
arcing plate INFORMATION
➭ In panels with HV HRC fuses, do not mount arcing plates in the cable compartment.
After installation of the cable T-plugs of phases L1 to L3, one arcing plate each must be
mounted in the cable compartment. The arcing plates are fitted on the mounting plate below
the operating mechanism box (tightening torque for the arcing plates: 20 Nm).
The associated floor plate of the floor cover must be mounted after installation of a row of
cable T-plugs (see page 156, "Mounting the floor plates").

Installation
INFORMATION
The arcing plates in the cable compartment have been pre-assembled at the factory. For
cable installation, the arcing plates must be removed.
➭ After cable installation, position the arcing plates as close as possible to the front towards
the cables according to the cable T-plugs used.
➭ The distance between the arcing plates and the cable T-plugs must not exceed a maximum
of 15 mm.
➭ The mounted arcing plates must not touch the cable T-plugs.
➭ Do not damage the cable T-plugs while mounting the arcing plates.
① Mounting plate
② Cable T-plugs
③ Air guide
④ Fixing at the switchgear
vessel
⑤ Switchgear vessel
Fig. 118: Arcing plate at the cable connection (one cable per
phase)
➭ Mount the arcing plate on the mounting plate in the cable compartment (tightening
torque: 20 Nm).
➭ Mount the floor plate of the floor cover (see page 156, "Mounting the floor plates").
Aligning and mounting The cable bracket can be mounted in the cable compartment at two different heights:
the cable bracket • Upper position: For panels with cable-type current transformers at the panel connection
• Lower position: For panels without cable-type current transformers at the panel connection
➭ Align the cable bracket and bolt it tight.
Fig. 119: Cable bracket, type C40
➭ Mount the cable clamps. Use cable clamps made of non-magnetizable materials (plastic,
aluminum) to fasten the high-voltage cables at the cable bracket, e.g. plastic clamps make
id-Technik (cable clamp K26-38 mm, cable clamp K36-52 mm).

Installation
➭ Connect the cable shield and the earthing of the plug housing to the cable bracket.
➭ Option: Mount the insulated earthing bar ① onto the cable bracket.
The use of an insulated earthing bar ① makes the connection of the cable shields to the zero-
sequence current transformer easier. All cable shields are connected to the insulated earthing
bar. An earthing cable ② leads from the earthing bar into the cable basement to the zero-
sequence current transformer. The zero-sequence current transformer earths all cable shields
through its own electric cable and leads them back. Without the use of the insulated busbar,
each individual cable shield must be led to the zero-sequence current transformer and
earthed.
Fig. 120: Basic scheme

Installation
➭ Hook the cable compartment cover in. Refit the 4 bolts.
DANGER
Internal arcing hazard and explosion hazard
Will cause death, injury or considerable property damage.
If the cable compartment cover is not bolted tight, the switchgear is not arc-resistant.
➭ Bolt the cable compartment cover together with the switchgear frame. Use the bolts with
cutting ring supplied with the switchgear.
➭ Fasten the cable compartment cover at the lower edge using self-tapping bolts with cutting
ring size M5 (tightening torque: 7 Nm).
① Bolt with cutting ring
Fig. 121: Earthing the cable compartment cover
Connecting up to four Up to 4 cables (plugs) can be connected per phase for 600-mm-wide panels.
cables per phase
After each three-phase cable connection, another arcing plate must be mounted in the cable
compartment. In like manner, the associated floor plate of the floor cover must be mounted
after each installed row of cable T-plugs (see page 156, "Mounting the floor plates").
INFORMATION
The arcing plates in the cable compartment have been pre-assembled at the factory. For
cable installation, the arcing plates must be removed.
➭ After cable installation, position the arcing plates as close as possible to the front towards
the cables according to the cable T-plugs used.
➭ The distance between the arcing plates and the cable T-plugs must not exceed a maximum
of 15 mm.
➭ The mounted arcing plates must not touch the cable T-plugs.
➭ Do not damage the cable T-plugs while mounting the arcing plates.
Example: Installation of 3 cables per phase
① Fastening at the partition to

the operating mechanism
compartment
② Cable T-plugs
③ Air guide
④ Switchgear vessel
Fig. 122: Arcing plates at the cable connection: Three cables per
phase

Installation
Mounting first row of ➭ Push rubber sleeves onto the cables.

cables ➭ Mount first row of cable T-plugs on phases L1 to L3.
➭ Pre-assemble the coach bolts on the first arcing plate. To do this, turn the fixing nut so far
that the bolt heads can still be fitted into the mounting plate later.
➭ Hook the arcing plate into the mounting plate and push into the correct position.
Mounting second row of ➭ Push rubber sleeves onto the cables.

cables ➭ Mount second row of cable T-plugs on phases L1 to L3.
➭ Pre-assemble the coach bolts on the second arcing plate. To do this, turn the fixing nut so
far that the bolt heads can still be fitted into the mounting plate later.
➭ Hook the arcing plate into the mounting plate and push into the correct position.
➭ Tighten the fixing nuts of the arcing plate. Tightening torque: 20 Nm.
Mounting third row of ➭ Push rubber sleeves onto the cables.

cables ➭ Mount third row of cable T-plugs on phases L1 to L3.
➭ Mount the floor plate or termination plate of the floor cover (see page 156, "Mounting the
floor plates").
➭ Mount the third arcing plate in the same way as the second one.
16.3 Panels 2000 A, 2500 A with double connections

For panels with 2000 A, 2500 A with double connections, an even number of cables per phase
(2, 4, 6 or 8 cables) is provided. It is also possible to connect an uneven number of cables per
phase (1, 3, 5 or 7 cables).
Fig. 123: Double connections with identification of the phase sequence
INFORMATION
If no cable plugs are used (asymmetrical power supply), one of the following cable lug types
must be used at the cable terminations:
• Tin-plated cable lugs
• Nickel-plated cable lugs
• Silver-plated cable lugs

Installation
Mounting arcing plates in The arcing plates in 2000 A, 2500 A panels are fitted on the mounting plate provided for this
the cable compartment purpose at the bottom of the switchgear vessel.
① First arcing plate

② Second arcing
plate
③ Third arcing plate
Fig. 124: Arcing plates in the cable compartment of 2000 A, 2500 A

panels
Mounting first row of ➭ Push rubber sleeves onto the cables.

cables ➭ Mount first row of cable T-plugs on phases L1 to L3.
➭ Pre-assemble the coach bolts on the first arcing plate. To do this, turn the fixing nut so far
that the bolt heads can still be fitted into the mounting plate later.
➭ Hook the arcing plate into the mounting plate and mount it according to the given
recommendation (see page 158, "Connecting cable T-plugs").
➭ Tighten the fixing nuts of the arcing plate. Tightening torque: 20 Nm.
Mounting second and ➭ Push rubber sleeves onto the cables.

third row of cables ➭ Mount second and third row of cable T-plugs on phases L1 to L3.
➭ Mount the floor plates or termination plate of the floor cover (see page 156, "Mounting the
floor plates").
➭ Mount second and third arcing plate in the same way as the first arcing plate.
16.4 Connecting surge arresters

Suitable surge arresters are listed in the operating instructions (see page 34, "Possible
combinations of cable connection types (T-plugs, coupling inserts) and surge arresters up to
24 kV").
The surge arresters are supplied with the supplementary equipment. Depending on their
version, they are pre-assembled with a support.
INFORMATION
If a power-frequency voltage test is performed after installing the switchgear, the surge
arresters must not be mounted before the test.
➭ Mount the surge arresters according to the manufacturer's assembly instructions.

➭ Ensure earth connection of the surge arrester according to the manufacturer's assembly
instructions.

Installation
Fig. 125: Mounted surge arrester (example)
16.5 Connecting surge limiters

You can only connect the surge limiter 3EH5 ... -5BA0 of Siemens (rated voltage
Ur = 3.6 kV / 4.8 kV / 7.2 kV).
For connection at the cable connection, the following options are possible:
• Euromold
Use of the cable T-plug (coupling plug) 300PB-630A-U-BEGRENZ for connection of the surge
limiter.
• nkt cables
Use of the cable T-plug (coupling plug) CC 12-630, CC 17.5-630 or CC 24-630 in
combination with the assembly kit 26 500 33 for connection of the surge limiter.
• Tyco Electronics Raychem
Use of the cable T-plug (coupling plug) SMOE 63862 for connection of the surge limiter.
➭ Mount the surge limiters and the outside-cone plugs according to the manufacturer's
instructions.

Installation
16.6 Connecting auxiliary circuits

The circuit-breaker switchgear NXPLUS C is delivered with operating and control equipment as
ordered.
The operating and control equipment as well as the terminals in the switchgear are identified
in the same way as in the associated circuit diagrams.
If the low-voltage compartment is installed later, the connections of the auxiliary circuits are
completed on site.
Fig. 126: Auxiliary circuits in the 600 mm low-voltage compartment
Fig. 127: Auxiliary circuits in the 900 mm low-voltage compartment
Lay, fix and connect the external cables in accordance with the national standards and
specifications (conductor, shielding, earthing).
Fig. 128: Open the right-hand leaf of the 900 mm low-voltage compartment door (open the
left-hand leaf and undo two bolts on the right-hand leaf)

Installation
There are wiring ducts on the right and on the left inside the cable compartment. The left-
hand duct is left empty at the factory and can be used for external cables. The right-hand duct
contains the internal panel wiring provided at the factory. For zero-sequence current
transformers in the cable basement, their cables are lead through the right-side cable duct.
➭ Lay the external cables in the left-hand wiring duct and fix them with cable straps.
Laying the cables in the right-hand wiring duct

➭ Lay current and voltage transformer leads with excessive length in meanders, as as shown
at position ③ .
Fig. 129: Cables in the right-hand wiring duct

① Current transformer lead
② Voltage transformer lead
③ Lead of capacitive voltage detecting system

Installation
➭ Lay wire groups keeping the maximum possible distance between them, and tight on the
earthed plate.
Fig. 130: Wire groups in right-hand wiring duct

① Current transformer lead ③ Lead of capacitive voltage detecting system
② Voltage transformer lead ④ Laying wire groups keeping the maximum
possible distance between them
Laying secondary customer cables in the left-hand wiring duct

For EMC-compatible laying, the cables are divided into functional groups: e.g. group 1 (signal
wires), group 2 (control wires), etc.
➭ Lay wire groups keeping the maximum possible distance between them, and tight on the
earthed plate.
Fig. 131: Wire groups in left-hand wiring duct

① Customer cable ③ Group 2
② Group 1 ④ Maximum possible distance between wire groups
The bus wires and the cables for the circuit-breaker and the three-position switch are
pluggable. The terminals are arranged in the low-voltage compartment.
➭ Lay the cables for the three-position switch and, if required, for the current and voltage
transformers in the low-voltage compartment.

Installation
➭ Plug pre-assembled bus wires on the bus wire terminals. Observe the coding of the 2-pole,
4-pole and 10-pole plugs.
➭ Plug the cables for the circuit-breaker and the three-position switch on the associated
terminals.
➭ If required, connect the current and voltage transformer leads.
Connecting the STG plug with the VBSTB4 modular terminal

For 2-, 4- and 10-pole STG plugs make PHOENIX CONTACT, observe the instructions for
installation and removal given hereafter.
INFORMATION
The information stated herein refers to the user instructions of PHOENIX CONTACT. The user is
obliged to inform himself about the latest state of the instructions before installation or
removal of the STG plugs, and to observe the manufacturer's instructions.
➭ Manufacturer's site: https://www.phoenixcontact.com
Mounting the ➭ Hold the STG plug horizontally over the plug shaft of the VBSTB4 modular terminal.
STG plug ➭ Push the STG plug horizontally into the modular terminal until the STG plug latches in.
✔ The STG plug is latched into the modular terminal and mounted.
Removing the ➭ Push the STG plug slightly to the screwing side until the latching noses come out of the
STG plug latching slots of the modular terminal.

Installation
➭ Pull the STG plug horizontally out of the VBSTB4 modular terminal.
✔ The STG plug is removed.

Installation
17 Installation of degree of protection versions IP31D,

IP32D and IP34D
If not stated otherwise, the assembly of the protection against vertically falling water drops is
shown by the example of a switchgear version with a small low-voltage compartment.
17.1 IP31D - protection against vertically falling water drops
INFORMATION
Mount the switchgear termination and busbar cover before the protection against vertically
falling water drops is mounted.
① Connecting plate
② Sealing strap for connecting
plates
③ Roof plate
④ Angle plate
Fig. 132: Setup of a protection against vertically falling

water drops
➭ Stick sealing strap on rear side of angle plate. The sealing strap must be in line with the
angle plate on the left and on the right.
① Angle plate
② Sealing strap
Fig. 133: Mounting the sealing strap on the angle

plate (view from the rear)
➭ Mount the angle plate on the low-voltage compartment using 4 self-tapping bolts M5x16.

Installation
Fig. 134: Mounting the angle plate
➭ Align the roof plate on the low-voltage compartment, and fasten it.
Fig. 135: Fastening the roof plate (view from the rear)
➭ Stick sealing strap on connecting plates.
➭ Bolt the connecting plates together with the roof plates and the angle plates on the right
and on the left. To do this, use 4 self-tapping bolts M5x16.
Fig. 136: Fastening the connecting plates (view from the rear)

Installation
Fig. 137: Completed protection against vertically falling water drops
Mounting the protection against vertically falling water drops on end panels
INFORMATION
In end panels, the angle plate must be mounted underneath the termination angle.
➭ If the termination angle is pre-assembled, remove the termination angle in advance.
➭ After mounting the angle plate, refit the termination angle.
plate
③ Angle plate with sealing strap
④ Mounted roof plate
⑤ Low-voltage compartment
⑥ Termination angle
⑦ Busbar cover
⑧ Roof plate
⑨ Sealing strap for left end plate
⑩ Left end plate
Fig. 138: Mounting the protection against vertically falling

water drops on the left end panel

Installation
Mounting the protection against vertically falling water drops on the high low-
voltage compartment
INFORMATION
If the low-voltage compartment is pre-assembled, execute the assembly operations of the
protection against vertically falling water drops for a small low-voltage compartment.
plate
③ Left end plate
④ Sealing strap for left end
plate
⑤ Roof plate
⑥ Angle plate with sealing strap
Fig. 139: Protection against vertically falling water drops on the

left end panel (view form the rear)
Attaching the sealing ➭ Stick a sealing strap ① between the panels on the rear wall of the low-voltage
straps compartment, in line with the partition plate.
➭ Stick a sealing strap ② in line with the upper edge of the busbar cover and the rear wall of
the low-voltage compartment.
① Sealing straps between the

panels
② Sealing straps on the rear
wall of the low-voltage
compartment
Fig. 140: Positions of the sealing straps
Mounting the protection against vertically falling water drops on panels with a width
of 900 mm
➭ The assembly operations correspond to the installation of the protection against vertically
falling water drops for panels with a width of 600 mm.
➭ Additionally, fasten the angle plate at the air guide and the busbar cover using
3 bolts M5x10.

Installation
① Connecting plates
② Roof plate
③ Sealing strap for
connecting plates
④ Angle plate
⑤ Air guide
Fig. 141: Protection against vertically falling water drops on a

panel with a width of 900 mm and mounted air guides
17.2 IP32D - protection against vertically falling water drops for switchgear
inclined up to 15°
If the switchgear is inclined by 15°, an edge protection provides personal safety and prevents
the ingress of vertically falling water drops in the switchgear.
➭ The operations correspond to those of the installation of the protection against vertically
falling water drops of IP31D.
① Connecting plates
② Sealing strap for connecting plates
③ Roof plate
④ Edge protection
⑤ Angle plate
Fig. 142: Roof plates with edge protection
④ Edge protection
Fig. 143: Edge protection when the switchgear is inclined

by 15°

Installation
Protection against vertically falling water drops IP32D for high low-voltage
compartment
➭ Installation is performed in the same way as for the protection against vertically falling
water drops for the high low-voltage compartment.
➭ Additionally, bolt the roof plates together and mount connecting braces.
① Nut-and-washer
assembly M8
② Connecting brace
③ Bolted joint of roof
plates
④ Self-tapping bolt M5
Fig. 144: Installation of the roof plate for protection against vertically
falling water drops on the high low-voltage compartment
17.3 IP34D - protection against splashing water from any direction

To protect the switchgear against splashing water from any direction, an additional sealing
angle must be mounted on the end panels before assembling the roof plates.
➭ Mount the sealing angle ⑤ on the low-voltage compartment using 2 self-tapping bolts
M5x12.
➭ The further operations correspond to those of the installation of the protection against
vertically falling water drops IP31D.
② Roof plate
③ Right end plate
④ Sealing strap for right end plate
⑤ Sealing angle, right side
⑥ Low-voltage compartment
⑦ Angle plate
⑧ Sealing strap for connecting plate
Fig. 145: Mounting the sealing angle (example: right end

panel)

Installation
18 Commissioning
DANGER
Hazardous voltage.
➭ Isolate.
WARNING
High speed moving mechanical parts
Mechanical components may move quickly, even remotely controlled.
➭ Do not remove any covers from switchgear put into operation.
➭ Do not reach into openings.
18.1 Final work

➭ Check the data on the rating plate and the auxiliary voltage of the control and end devices
as against the requirements.
➭ Check ready-for-service indicator (see page 189, "Ready-for-service indicator").
➭ Check switchgear fixing.
➭ Check the earthing connections.

➭ Check the bolted joints of the low-voltage equipment at random.
➭ Check all parts of the switchgear that have been disassembled and assembled again at site
during installation or that have been installed subsequently, in order to verify correct
assembly and completeness.
Auxiliary transformer Do only put the auxiliary transformer panel into operation when the transformer is completely
panel mounted.
➭ Check whether the transformer and the connection cables are completely mounted and
connected.
➭ Check whether the transport angles of the transformer connection cables are removed.
Closing the front cover

DANGER
If the front cover is not bolted tight, the switchgear is not arc-resistant.
➭ Bolt the front cover together with the switchgear frame. Use the bolts with cutting ring
supplied with the switchgear.
➭ Hook the front cover in.

➭ Fasten the front cover at the lower edge tight using 2 bolts with cutting ring M5 (tightening
torque: 7 Nm).

Installation
Fig. 146: Fastening the front cover
Closing the cable ➭ Hook the cable compartment cover in.

compartment cover
DANGER
If the cable compartment cover is not bolted tight, the switchgear is not arc-resistant.
➭ Bolt the cable compartment cover together with the switchgear frame. Use the bolts with
cutting ring supplied with the switchgear.
➭ Fasten the cable compartment cover at the lower edge using 4 bolts with cutting ring M5
(tightening torque: 7 Nm).
Fig. 147: Fastening the cable compartment cover
Checking auxiliary cable ➭ Check correct wiring according to the circuit diagrams.
connections ➭ Check clamping and plug-in connections at random (perfect contact, labels, etc.).
Checking high-voltage ➭ Check earthing of cable terminations on all connected high-voltage cables.
connections ➭ If required, test cables (see page 266, "Cable testing").
Feeder without cables ➭ Earth and close the feeder. Cover the bushings with surge-proof caps.
Tyding up and visual ➭ Remove any attached instruction labels and documents that are not required anymore for
inspection operation.
➭ Remove any tools, materials etc. that are not required anymore from the area of switchgear.
➭ Remove any dirt from the area of the switchgear (cleaning agent ARAL 4005 or HAKU 1025
and lint-free rag/brush).
➭ Fit all covers.
➭ Put the covers on the plug-in sockets of the capacitive voltage detecting systems.
➭ Touch up scratches and impacts in the surface painting. Available kit: Touch-up set (spatula
and paint) and paint pen.

Installation
Checking protection ➭ Check the version of the firmware installed on the protection devices, and update if
devices required, see page 8, "IT security".
18.2 Checking the accessories

➭ Place the following accessories ready to hand:
• Installation and operating instructions
• Operating levers for the three-position disconnector:
- Operating lever with black ball handles for DISCONNECTING function
- Operating lever with red ball handles for EARTHING/READY-TO-EARTH function
• Hand crank for charging the circuit-breaker closing spring (with freewheel)
• Adapter for emergency operation (only for panels with a width of 900 mm and panels with
motor operating mechanism)
• Double-bit key with a diameter of 3 mm for the door of the low-voltage compartment
• Double-bit key with a diameter of 5 mm for the voltage transformer disconnector and the
door of the low-voltage compartment
• Circuit diagrams
• Torx screwdriver T25
18.3 Instructing operating personnel

➭ Instruct operating personnel in theory and practice of switchgear operation.
18.4 Function test / Test operation
WARNING
Hazardous voltage
Can cause death or injury.
➭ Perform mechanical function test with primary part de-energized and without auxiliary
voltage. Do not perform mechanical function test while energized.
➭ Do not energize switchgear until mechanical function test has been successfully
completed.
WARNING
been performed:
- Trip the MCB.
instructions:

Installation
CAUTION
Using an incorrect hand crank can cause injury.
➭ Use exclusively the hand crank provided with the switchgear accessories.
The hand crank supplied features a freewheel function. The freewheel function
disconnects an inserted hand crank from the charging system when the motor charges the
closing spring.
Mechanical function test ➭ Switch the three-position switch and the circuit-breaker several times to CLOSED and OPEN
position, observing the correct indication of the associated position indicators.
➭ Check mechanical interlocks and covers for easy operation.
Readjusting the After the mechanical function test, the freewheel of the OPEN and CLOSE pushbuttons of the
freewheel of the circuit-breaker can be readjusted. The factory-set freewheel is approx. 5...7 mm.
pushbuttons
➭ Measure the freewheel of the two pushbuttons (e.g. by means of a tape measure or vernier
caliper).
① Freewheel (approx.
7...5 mm)
➭ Remove the front cover of the circuit-breaker panel.

➭ Measure the distance from the knurled bolt to the plastic nut.
➭ Hold the housing of the pushbutton at the front.

➭ To adjust the freewheel to the requested dimension, turn the knurled bolt
(recommendation: for turning the bolt more easily, wear a glove).
➭ Refit the front cover.
➭ Test fuse tripping with test fuse.

➭ Check HV HRC fuse-links.

Installation
Unlocking the If the interlock at the control gate is equipped with an interlocking solenoid and if there is no
interlocking solenoids auxiliary voltage available, the control gate is blocked. The interlocking can be bypassed as
follows:
Fig. 148: Expanding rivet at the control gate
CAUTION
If the interlock is bypassed, switching operations are possible that can cause an arcing fault.
➭ Only bypass the interlock when the feeder is in a no load condition and not carrying
current.
Push the control gate from center position to right position:

➭ Remove left-hand expanding rivet ① . Insert the screwdriver into the left-hand opening and
push the interlocking solenoid back. Push the control gate to the right. The left-hand
interlocking solenoid is released again, blocking further movements.
Push the control gate from center position to left position:
➭ Remove right-hand expanding rivet ② . Insert the screwdriver into the right-hand opening
and push the interlocking solenoid back. Push the control gate to the left. The right-hand
interlocking solenoid is released again, blocking further movements.
✔ After work completion, insert the expanding rivet again.
Activating the
undervoltage release NOTICE
Blocked undervoltage release
Can cause property damage.
The undervoltage release will not function if its retaining bolt is inserted in position A. After test
operation without auxiliary voltage, the undervoltage release must be activated.
➭ Remove the retaining bolt from position A and insert it in position B.
The undervoltage releases mounted in the circuit-breaker must be activated for operation.
The circuit-breaker operating mechanism is located in the central part of the panel behind the
ON/OFF pushbuttons.
➭ Remove the front cover of the circuit-breaker.
➭ To activate the undervoltage release, shift the retaining bolt of the striker from position A to
position B.
➭ Refit the front cover.

✔ The circuit-breaker operating mechanism is now ready for operation with undervoltage
release.

Installation
Electrical function test Before commissioning, verify correct operation of the switchgear by test operation. Perform
test operation without high voltage.
INFORMATION
For test operation, switch the three-position disconnector to the basic position.
➭ Switch the three-position disconnector for the DISCONNECTING and EARTHING functions
to OPEN position by hand.
➭ Switch on all auxiliary voltages and control voltages and verify correct polarity.
✔ The motor of the circuit-breaker operating mechanism charges the closing spring.
➭ Test panels with electromagnetically interlocked three-position switch only with applied
auxiliary voltage.
➭ Check whether the mechanical and/or electrical interlocking conditions are fulfilled without
using excessive force.
➭ Check the position indicators of the three-position disconnector.
➭ Switch the three-position switch and the circuit-breaker several times to CLOSED and OPEN
position, both directly at the panel and from remote.
- Check whether the positions are correctly indicated on the panel and in the control room,
if applicable.
- Check whether the auxiliary switches and the position switches operate correctly.
➭ After operating the three-position switch, check whether the operating levers can be
pushed onto the operating shafts.
If not, the motor may have jumped over due to reverse polarity. Inform the regional
Siemens representative.
➭ Check the function of the closing solenoid by electrical operation.
➭ Check the function of the shunt releases, c.t.-operated releases and undervoltage releases
by electrical operation.
Faults during test • The three-position disconnector does not move to the desired position during the first
operation electrical operation. (Example: The three-position disconnector moves to the "EARTHING
SWITCH CLOSED" position instead of the "DISCONNECTOR CLOSED" position).
• The control system of the three-position disconnector has detected the incorrect execution
of the command and is in fault mode. In this condition, no further electrical switching
operations are possible.
CAUTION
High voltage and explosion hazard
Putting defective switchgear into operation can cause serious injury and property
damage.
➭ If there are any faults that cannot be cleared on site: Do not put the switchgear into
operation.
➭ Inform the regional Siemens representative.
Fault clearing ➭ Check the polarity of the auxiliary voltage and the motor connection.
➭ Switch the operating mechanism manually back to the basic position. The position
indicator for the DISCONNECTING and EARTHING functions shows OPEN (see page 192,
"Operating the three-position switch").
➭ Reset the fault mode: The fault mode can be reset in 2 different ways:
- Switch the auxiliary voltage off and on again.
- Operate the reset button (through the opening at the front of the device).
➭ The fault mode is reset by switching the auxiliary voltage off and on, or by operating the
covered reset button through the opening at the front of the device.
✔ The three-position disconnector can be put into operation again.
➭ Perform test operation of the three-position disconnector.
Completing test operation ➭ Switch all switching devices to OPEN position.

Installation
18.5 Performing the power- frequency voltage test

If required, a test with rated short-duration power-frequency withstand voltage can be
performed on site. The busbar voltage transformers are designed for a repeat test at 80% U D
and 50 Hz according to IEC 62271-200.
At the factory, the individual feeders are routine-tested by means of a rated short-duration
power-frequency voltage test.
As a rule, the test with these high power-frequency voltage test levels is performed before
connecting the cables. If the cables are already connected, power-frequency voltage test
equipment with a very high rating is necessary, and the permissible test voltage of the
connected cables would be exceeded.
For detailed information about cable tests, see page 266, "Cable testing".
NOTICE
Voltage indicators may be damaged by test voltage during cable tests.
May cause property damage.
➭ Short-circuit the voltage indicators with short-circuit plugs at the earthing points of the test
sockets.
Fig. 149: Short-circuit plug, make Kries, Fig. 150: Short-circuit plug, make
order number 2500029 Horstmann, order number
51-9904-001
Preparing the test ➭ Switch the circuit-breaker and the three-position switch of the incoming feeder to CLOSED
position to perform the power-frequency voltage test.
➭ Switch all other three-position switches to EARTHED position.
➭ Earth the voltage transformers at the feeder via the voltage transformer disconnector.
➭ If applicable, remove the surge arresters from the busbar and the incoming feeder.
➭ Cover the coupling units of the surge arresters with surge-proof caps.
➭ Apply the power-frequency test voltage in a surge-proof way at the cable connection
bushing via test adapters.
✔ Now you can carry out the test.
Performing the test ➭ Earth adjacent phases.

➭ Test phases L1, L2 and L3 consecutively for 60 seconds with the rated short-duration power-
frequency voltage.
Completing the check ➭ Switch the voltage transformer disconnector to CLOSED position.
➭ Mount the surge arresters.

Installation
18.6 Primary injection test

A primary injection test can be performed on the panels.
Performing the test To test the current transformers, switch the three-position switch of the panel to be tested to
"EARTHED" position and the circuit-breaker to "CLOSED" position.
After that, the test current is applied through the bushings of the cable connection against the
earthing busbar by means of a suitable test unit. Power supply can take place via one or three
phases.
After applying the test current, the secondary measuring devices and tripping systems can be
tested.
18.7 Correcting circuit diagrams

➭ Note any modifications which may have been made during installation or commissioning in
the supplied circuit diagrams.
➭ To have the modifications in the circuit diagrams included, send the corrected circuit
diagrams to the regional Siemens representative.
18.8 Applying operating voltage
DANGER
Hazardous voltage and internal arcing
Do not apply operating voltage before the following instructions have been executed:
➭ Observe the specifications for prevention of accidents.
➭ Observe the operating instructions and work instructions of the switchgear operator.
➭ Install the switchgear according to the installation instructions and drawings supplied.
➭ Perform electrical and mechanical and function test successfully.
➭ Instruct the operating personnel in theory and practice of switchgear operation.
➭ Fit all covers and bolt them tight.
➭ Switch all circuit-breakers and vacuum contactors to OPEN position.
➭ Switch the three-position switches in all panels to OPEN position.
➭ Earth feeders without connected cables. Close all bushings in a surge-proof way.
➭ Switch off connected consumers in all outgoing feeders.
➭ Short-circuit unused current transformers on the secondary side.
➭ Operate unused voltage transformers open on the secondary side.
➭ To assure a consistent phase sequence in the entire switchgear assembly, check the phase
sequence in all incoming and outgoing feeders before connecting them to the busbar.
Energizing incoming ➭ Energize all incoming feeders in the respective opposite substation.
feeders
Verifying correct Verify correct terminal-phase connections of all incoming feeders:

terminal-phase
connections
Preconditions • Use phase comparison test unit according to IEC 61243-5 or VDE 0682-415.
• The panel of the incoming feeder to be tested must be in OPEN position.
• The opposite substation must be de-earthed and live.
Performing the test ➭ Remove the covers of the capacitive test sockets from phase L1 on the incoming feeder to
be tested and on an already energized incoming feeder.
✔ The plug-in sockets of the capacitive voltage detecting system on phase L1 are accessible.
➭ Plug the measuring cables of the phase comparison test unit into the plug-in sockets of the
capacitive voltage detecting system according to the operating instructions.

Installation
➭ Perform phase comparison according to the operating instructions of the phase comparison
test unit and read the indication.
➭ Remove the measuring cables from the plug-in sockets.
➭ Refit the covers of the capacitive test sockets on both incoming feeders.
Checking further phases ➭ Perform phase comparison for the phases L2 and L3 in the same way.
✔ If the phase comparison test unit has shown coincidence on all 3 phases, the phase
sequence of the tested incoming feeder is correct.
✔ The incoming feeder can be energized.
Applying voltage to the If the phase sequence of all incoming feeders is correct, the incoming feeders can be
busbar connected to the busbar:
➭ Close the three-position disconnector (the three-position disconnector must be operated in
no-load condition, see page 186, "Operation").
➭ Close the circuit-breaker or superior circuit-breaker.
✔ The busbar of the switchgear is live.
Energizing consumer When all incoming feeders are connected to the busbar:
feeders
➭ One after the other, energize all consumer feeders with connected consumers.
✔ When all consumer feeders are energized, the switchgear is completely in operation.
Documenting the ➭ Document the modifications occurred during installation or commissioning.

commissioning ➭ Document the modifications in the circuit diagram.
➭ Send the modifications to the regional Siemens representative.
After commissioning ➭ Observe the Five Safety Rules for working in the switchgear:
- Isolate.
- Secure against reclosing.
- Verify safe isolation from supply.
- Earth and short-circuit.
- Cover or barrier adjacent live parts.
➭ Observe the locally applicable specifications for prevention of accidents.
➭ If after commissioning further work is required in the area of the switchgear, install warning
signs on the switchgear.
Access for working in the area of the switchgear must only be granted to the following
persons:
- Electricians and persons who have been properly instructed in electrical engineering
- Persons under the supervision of electricians and persons who have been properly
instructed in electrical engineering

Operation
Operation
DANGER
The internal arc classification of the switchgear has only been verified for the switchgear sides
qualified according to IEC 62271-200 and with closed compartments.
➭ Determine the IAC classification of the switchgear by means of the data on the rating plate.
➭ With internal arc classification IAC A FL, no persons are allowed to stay in the area behind
the switchgear.
➭ The switchgear must have been installed in accordance with the instruction manuals and
drawings.
➭ All covers of the switchgear must be closed.
➭ Regulations for access to switchgear areas without internal arc classification according to
IEC 62271-200 must be defined by the switchgear operator.
CAUTION
Switching without service readiness can cause serious injury or property damage.
➭ Check service readiness of the switchgear before performing any switching operation. The
pointer of the ready-for-service indicator must be in the green area.
➭ If the pointer of the ready-for-service indicator is in the red area:
- All panel types except circuit-breaker panels: Do not operate the switchgear.
- Contact the Siemens Service Hotline.

Operation
19 Control elements and indicators
Fig. 151: Control board of circuit-breaker Fig. 152: Control board of circuit-breaker
panel (panel width 600 mm) panel (panel width 600 mm) with
30000 operating cycles
Fig. 153: Control board of circuit-breaker panel (panel width 900 mm)
① Position indicator for three-position switch ② Position indicator for three-position switch
(DISCONNECTING function) (EARTHING/READY-TO-EARTH function)
③ Interrogation lever ④ OFF pushbutton for circuit-breaker
⑤ Sockets for voltage detecting system, feeder ⑥ "Feeder earthed" locking device
⑦ Operations counter for circuit-breaker ⑧ "Spring charged" indicator for circuit-breaker
⑨ Position indicator for circuit-breaker ⑩ Test sockets for voltage detecting system,
busbar (option)
⑪ ON pushbutton for circuit-breaker ⑫ Manual charging for circuit-breaker
⑬ Actuating opening for earthing switch (EARTHING/ ⑭ Actuating opening for disconnector
READY-TO-EARTH function) (DISCONNECTING function)
⑮ Control gate for actuating openings ⑯ Ready-for-service indicator

Operation
19.1 Position indicators
EARTHED Faulty position

Switch position CLOSED OPEN Contacts are not in
READY-TO-EARTH defined end position
Disconnector —
Earthing switch —
Circuit-breaker and
— —
vacuum contactor
19.2 "Spring charged" indicator
Closing spring charged Closing spring not charged
19.3 Operations counter

One operating cycle corresponds to one closing operation and one opening operation of the
circuit-breaker.
Number of operating
cycles

Operation
19.4 Ready-for-service indicator
CAUTION
① Switchgear ready for service (green area)

② Switchgear not ready for service (red area)
③ Pointer
Fig. 154: Ready-for-service indicator
19.5 Circuit-breaker locking device for "feeder earthed"

The circuit-breaker locking device for "feeder earthed" is operated to lock a circuit-breaker
panel with earthed feeder and secure it against de-earthing.
The operated locking device can be padlocked.
As standard, the locking device can only be operated when the three-position disconnector is
in READY-TO-EARTH position and the circuit-breaker is in CLOSED position. Operating the
locking device in other switch positions is locked as standard.
NOTICE
Maloperation of the locking device
Can cause considerable property damage.
For a panel optionally equipped without interlocking between locking device and three-
position disconnector: If the circuit-breaker and the three-position disconnector are in
CLOSED position, do not operate the locking device.
If the locking device is operated, all electrical and mechanical opening commands (e.g.
protection tripping) are ineffective.
➭ Operate the locking device only under the following conditions:
- Three-position disconnector switched to READY-TO-EARTH position.
- Circuit-breaker switched to CLOSED position.
Preconditions • Three-position disconnector in "READY-TO-EARTH" position

• Circuit-breaker in CLOSED position
• Shackle diameter of the padlock: Min. 6 mm.
Actuating the locking ➭ Push the lever of the locking device upwards.
device
Fig. 155: Circuit-breaker locking device
➭ Fit and lock the padlock.

Operation
20 Operating the circuit-breaker
20.1 Closing the circuit-breaker

If there is no block active from the mechanical interlock, the circuit-breaker can be closed
electrically (if provided) or mechanically.
Control voltage failure If the control voltage fails, the circuit-breaker must be closed mechanically (pushbutton).
Closing the circuit-breaker ➭ Operate the ON pushbutton in the mechanical or electrical control board.
✔ The circuit-breaker is closed.
20.2 Opening the circuit-breaker

The circuit-breaker can be opened electrically (if provided) or mechanically.
Control voltage failure If the control voltage fails, the circuit-breaker must be opened manually.
Locking device If the feeder is earthed through the three-position disconnector and the circuit-breaker, and if
the "feeder locking device" is fitted, all electrical opening commands are ineffective.
If the locking device is padlocked, the circuit-breaker cannot be opened mechanically either.
Opening the circuit- ➭ Operate the OFF pushbutton in the mechanical or electrical control board.
breaker ✔ The circuit-breaker is open.
20.3 Charging the closing spring
Closing spring The closing spring is charged automatically after applying control voltage. The energy
required for the operating sequence OPEN-CLOSE-OPEN (auto-reclosing) is stored in the
closing spring about 15 seconds after closing the circuit-breaker operating mechanism.
Control voltage failure If the control voltage fails, the closing spring can be charged with a hand crank. The hand
crank is equipped with a freewheel. If the control voltage returns while the hand crank is
inserted, the freewheel prevents injuries caused by the starting motor.
CAUTION
Using an incorrect hand crank can cause injury.
➭ Use exclusively the hand crank provided with the switchgear accessories.
The hand crank supplied features a freewheel function. The freewheel function
disconnects an inserted hand crank from the charging system when the motor charges the
closing spring.
➭ Remove cover from cutout.

➭ Insert hand crank.
➭ Turn hand crank clockwise approx. 30 turns.
✔ The indication "closing spring charged" appears in the inspection window.
➭ Remove hand crank.
➭ Close cutout with cover.

Operation
20.4 Circuit-breaker test operation
Without auxiliary voltage Perform the following actions to guarantee that the circuit-breaker is ready for operation:
➭ Charge the closing spring (see page 190, "Charging the closing spring").
➭ Operate the ON pushbutton in the mechanical control board.
✔ The circuit-breaker is closed.
➭ Operate the OFF pushbutton in the mechanical control board.
✔ The circuit-breaker is open.
On circuit-breakers with undervoltage release 3AX1103:
NOTICE
Blocked undervoltage release
Can cause property damage.
The undervoltage release will not function if its retaining bolt is inserted in position A. After test
operation without auxiliary voltage, the undervoltage release must be activated.
➭ Remove the retaining bolt from position A and insert it in position B.
➭ Shift the retaining screw of the striker from position A to B to activate the undervoltage
release.
With auxiliary voltage ➭ Switch on the supply voltage.

(motor operating ✔ The motor operating mechanism starts up and charges the closing spring.
mechanism)
➭ Check whether the "spring charged" indication appears.
➭ Close the circuit-breaker.

✔ The closing spring is recharged automatically.
➭ Check whether the position indication "circuit-breaker CLOSED" appears.
➭ Open the circuit-breaker.
➭ Check whether the position indication "circuit-breaker OPEN" appears.

Operation
21 Operating the three-position switch
CAUTION
INFORMATION
Operating the three-position disconnector
When the circuit-breaker is in CLOSED position, the three-position disconnector cannot be
operated.
➭ Switch the circuit-breaker to OPEN position.
INFORMATION
Switching noise of the three-position switch
• The spring-operated mechanism / spring-operated/stored-energy mechanism (turning the
operating lever by 90°) switches with a loud noise.
• The slow motion mechanism (turning the operating lever by 180°) switches almost without
any noise.
This section describes the switching operations:

• DISCONNECTING and READY-TO-EARTH with the three-position disconnector
• DISCONNECTING and EARTHING with the three-position switch-disconnector
The manual switching operations DISCONNECTING or EARTHING/READY-TO-EARTH must be
preselected. Preselection is only possible if the associated switching operation is permissible
and the interrogation lever is operated.
The operating levers for the three-position switch are coded and identified by color:
• Operating lever for DISCONNECTING operation: Black ball handles.
• Operating lever for EARTHING/READY-TO-EARTH operation: Red ball handles
• The heads of the operating levers for panels with widths of 600 and 900 mm are identified
with symbols:
Operating lever for DISCONNECTING operation Operating lever for EARTHING/READY-TO-

EARTH operation
Fig. 156: Symbols on operating lever with Fig. 157: Symbols on operating lever
black ball handles with red ball handles

Operation
Operation of spring-operated mechanism or spring-operated/stored-energy mechanism

(600 mm panel width)
Switching operation Selection of operating lever Operation OPEN position
Color Symbol
DISCONNECTING Operating lever Turn the operating
with black ball lever 90° counter-
handles clockwise.
EARTHING/READY-TO- Operating lever Turn the operating

EARTH with red ball lever 90°
handles clockwise.
Operation of slow motion mechanism (900 mm panel width)
Switching operation Selection of operating lever Operation OPEN position
Color Symbol
DISCONNECTING Operating lever Turn the operating
with black ball lever 180° counter-
handles clockwise.
EARTHING/READY-TO- Operating lever Turn the operating

EARTH with red ball lever 180°
handles clockwise.
21.1 Closing the three-position switch

➭ Check service readiness (see page 189, "Ready-for-service indicator").
➭ In circuit-breaker panels: Unlock the locking device at the circuit-breaker and open the
circuit-breaker.
➭ Push the interrogation lever downwards.
➭ Push the control gate to the left.
✔ The opening for the DISCONNECTING operation is free.
➭ Insert the operating lever for the DISCONNECTING operation (black ball handles) and,
- with spring-operated mechanism / spring-operated/stored-energy mechanism (600 mm
panel), turn 90° clockwise;
- with slow motion mechanism (900 mm panel), turn 180° clockwise.
✔ The three-position switch is closed.
➭ Remove the operating lever for the DISCONNECTING operation.
✔ The interrogation lever and the control gate return to their initial position.
21.2 Opening the three-position switch

➭ In circuit-breaker panels: Open the circuit-breaker.
➭ Push the control gate to the left.
✔ The opening for the DISCONNECTING operation is free.
➭ Insert the operating lever for the DISCONNECTING operation (black ball handles) and
panel), turn 90° counter-clockwise;
- with slow motion mechanism (900 mm panel), turn 180° counter-clockwise.

Operation
✔ The three-position switch is open.

➭ Remove the operating lever for the DISCONNECTING operation.
21.3 Earthing/ready-to-earth with the three-position switch
CAUTION
Operating the three-position disconnector under load can cause injury or property
damage.
A mechanical interlock prevents, as standard, the three-position disconnector from being
operated under load. The switchgear can optionally be equipped in accordance with a
customer-specific intrlocking and control scheme.
➭ If the customer-specific interlocking and control scheme requires that the panel be
provided without electromechanical or mechanical interlocks, the three-position
disconnector can be operated under load.
➭ Do NOT operate the three-position disconnector under load.
WARNING
Hazardous voltage
Can cause death or serious injury.
In panels with circuit-breaker, the earthing process is not completed as long as the circuit-
breaker remains open.
➭ Switch the three-position disconnector to READY-TO-EARTH position.
➭ Close the circuit-breaker.
➭ In circuit-breaker panels: Open the circuit-breaker.

➭ Push the control gate to the right.
✔ The opening for the EARTHING/READY-TO-EARTH operation is free.
➭ Insert the operating lever for the EARTHING/READY-TO-EARTH operation (red ball handles)
and,
panel), turn 90° clockwise;
- with slow motion mechanism (900 mm panel), turn 180° clockwise.
✔ The three-position switch is closed.
➭ Remove the operating lever for the EARTHING/READY-TO-EARTH operation again.
➭ In circuit-breaker panels, close and lock the circuit-breaker.
21.4 De-earthing with the three-position switch

➭ In circuit-breaker panels: Unlock the locking device at the circuit-breaker and open the
circuit-breaker.
✔ The opening for the EARTHING/READY-TO-EARTH operation is free.
➭ Insert the operating lever for the EARTHING/READY-TO-EARTH operation (red ball handles)
and,
panel), turn 90° counter-clockwise.
- with slow motion mechanism (900 mm panel), turn 180° counter-clockwise.

Operation
✔ The three-position switch is open.

➭ Remove the operating lever for the EARTHING/READY-TO-EARTH operation again.
21.5 Operating the three-position switch with motor-operating mechanism

The switching operations DISCONNECTING, EARTHING and READY-TO-EARTH of the three-
position disconnector/switch-disconnector can be performed with a motor operating
mechanism (option).
Three-position switches with motor operating mechanisms can also be controlled from
remote according to their design.
21.6 Protection tripping of the switch-fuse combination

If the switch-fuse combination was tripped by a shunt release or a fuse-link:
• The position indicator of the three-position switch-disconnector shows a black-red bar.
• The operating shaft for the DISCONNECTING operation is still in CLOSED position.
• The motor operating mechanism is out of operation.
Remedy ➭ Insert the operating lever for the DISCONNECTING operation (black ball handles) and switch
the three-position switch-disconnector to OPEN position (see page 215, "Circuit-breaker
panel: Disconnecting the feeder from the busbar").
Fig. 158: Switching the three-position switch-disconnector to OPEN position, example for
600 mm panel width

Operation
➭ Switch the three-position switch-disconnector to EARTHED position (see page 216, "Circuit-
breaker panel: Earthing the feeder ").
Fig. 159: Switching the three-position switch-disconnector to EARTHED position, example

for 600 mm panel width
✔ The opening spring is recharged.

➭ Check the HV HRC fuse-links and replace, if required (see page 208, "Replacing HV HRC fuse-
links").
➭ De-earth the three-position switch-disconnector (see page 217, "Circuit-breaker panel: De-
earthing the feeder").
➭ Switch the three-position switch-disconnector to CLOSED position (see page 214, "Circuit-
breaker panel: Connecting the feeder to the busbar").
✔ The opening spring is recharged.
21.7 Emergency operation of the three-position switch with slow motion

mechanism (900 mm panel width)
If the motor voltage fails in three-position switches with motor operating mechanism and the
three-position switch is in neither of the two end positions, the three-position switch must be
operated manually.
Fig. 160: Position indicator for DISCONNECTING function in faulty position
Fig. 161: Position indicator for EARTHING function in faulty position
To do this, the adapter for emergency operation has to be pushed on the standard operating
lever.

Operation
Adapter for emergency ➭ Push emergency operation adapter on operating lever for three-position switch.
operation
NOTICE
Incorrect alignment of the operating lever
The noses of the operating lever can damage the position indicator or the operating
mechanism of the three-position switch.
➭ Align the operating lever with pushed-on adapter by the slots of the adapter.
Fig. 162: Marking (long slot) on operating lever with pushed-on adapter
Fig. 163: Marking (short slot) on operating lever with pushed-on adapter
The noses of the operating lever are not significant for evaluating the position of the
operating mechanism.
End positions of the three-position switch while switching with the operating lever
with pushed-on adapter
NOTICE
The operating lever does not have a stop.
Switching beyond the end position of the three-position switch will damage the three-
position switch if the adapter is pushed on.
➭ Observe the markings on the adapter of the operating lever.
Insert the operating lever with pushed-on adapter in such a way that the inner slot of the
adapter fits on the pin of the operating shaft.
Fig. 164: Inserting the operating lever with pushed-on adapter

Operation
End positions of DISCONNECTOR
Adapter position Position of long Adapter position Position of long

slot: left slot: right
Position of short Position of short
slot: right slot: left
The disconnector is in CLOSED position. The disconnector is in OPEN position.
End positions of EARTHING SWITCH
Adapter position Position of long Adapter position Position of long

slot: bottom slot: top
Position of short Position of short
slot: top slot: bottom
The earthing switch is in CLOSED position. The earthing switch is in OPEN position.
Emergency operation of If the switching device does not reach its end position, e.g. due to a failure of the auxiliary
the DISCONNECTING voltage during disconnector operation, push the operating lever with pushed-on adapter onto
function the hexagonal shaft for the DISCONNECTING function in such a way that the pin of the
hexagonal shaft fits in the inner slot of the adapter.
Fig. 165: Operating lever with pushed-on adapter (DISCONNECTING function)

Operation
Initial situation Push the interrogation lever downwards and hold it
Push the control gate to the left (the interrogation To open the disconnector, insert the operating lever with
lever locks in lower position. The actuating pushed-on adapter and turn counter-clockwise until the
opening for the DISCONNECTING function opens) slots at the adapter are horizontal to the actuating opening
(the position indicator is in OPEN position)
Remove the operating lever with pushed-on End position

adapter. (The interrogation lever and the control Remove the adapter from the operating lever and lay it back
gate return to their initial position. The actuating into the service flap
opening closes)

Operation
Emergency operation of If the switching device does not reach its end position, e.g. due to a failure of the auxiliary
the EARTHING function voltage during earthing switch operation, push the operating lever with pushed-on adapter
onto the hexagonal shaft for the EARTHING function in such a way that the pin of the
hexagonal shaft fits in the inner slot of the operating adapter.
Fig. 166: Inserting the operating lever with pushed-on adapter (EARTHING function)
Initial situation Push the interrogation lever downwards and hold it
Push the control gate to the left (the interrogation lever To open the earthing switch, insert the operating lever
locks in lower position. The actuating opening for the with pushed-on adapter and turn counter-clockwise
EARTHING function opens) until the slots at the adapter are vertical to the
actuating opening (the position indicator is in OPEN
position)
Remove the operating lever with pushed-on adapter. End position

(The interrogation lever and the control gate return to Remove the adapter from the operating lever and lay it
their initial position. the actuating opening closes) back into the service flap
Switching operations Perform further manual switching operations only with the associated operating lever for the
after emergency DISCONNECTING or EARTHING functions.
operation

Operation
22 Work-in-progress earthing
Visible earthing without ➭ Earth the panel.
removing the cables ➭ Plug the adapter for work-in-progress earthing onto the cable T-plug of the connected
cables.
① Adapter for work-in-progress

earthing
➭ Earthing accessories from different manufacturers can be connected to the spherical bolts
of the adapters. Diameter of the spherical bolts: 20 or 25 mm.
Example for earthing accessories:

Operation
➭ Connect earthing accessories with the earthing busbar via one of the connection points of
the pulled-out earthing bar (option).
CAUTION
Thermal overload by too high short-circuit current at the connection point of the pulled-
out earthing bar.
Can cause serious injury or property damage.
➭ Load the pulled-out earthing bar with a short-circuit current of 25 kA 3 s as a maximum.
➭ Another connection point of the pulled-out earthing bar, which can be loaded with up to
31.5 kA 3 s, is located behind the cover of the right-hand wiring duct. To use the
connection point, remove the cover of the wiring duct.
① Earthing busbar
② Connection point (M12) for earthing
accessories (max. 25 kA 3s)
③ Connection point (M12) for earthing
accessories (max. 31.5 kA 3s)
④ Cover of right-hand wiring duct
Make Adapter for work- Diameter of For cable T-plugs

in-progress spherical bolt
earthing
3M ER 23 20 mm 93-EE 705-6
93-EE 715-6
Nexans Euromold 300GP-B-KB-20 20 mm 430TB/G; 300PB/G
300GP-B-KB-25 25 mm K430TB-630A; K300PB-630A
400GP-B-KB-20 20 mm 400TB/G; 440TB/G
400GP-B-KB-25 25 mm K400TB/G; K440TB/G
800GP-B-KB-20 20 mm 484TB/G; 804PB/G
800GP-B-KB-25 25 mm 489TB/G; 809PB/G
K484TB/G; K804PB/G
K489TB/G; K809PB/G
nkt cables E 20 20 mm CB 12-630; CC 12-630
25 mm CB 17.5-630; CC 17.5-630
CB 24-630; CC 24-630
CB 24-1250-2; CC 24-1250-2
CB 36-630(1250); CC 36-630(1250)
CB 42-1250-3; CC 42-2500-3
Südkabel ER 23 20 mm SET 12; SEHDT 13; SEHDK 13.1
SET 24; SEHDT 23; SEHDK 23.1
Tyco Electronics RSTI-68EA20 20 mm RSTI-58xx; RSTI-CC-58xx
Raychem RSTI-68EA25 25 mm RSTI-395x; RSTI-CC-395x; RSTI-595x; RSTI-CC-595x
GCA CJB10-EB Bolt CJBxx-630; CJBKxx-630
ABB Kabeldon JPB 630 Bolt CSE-A xx630-xx
Cellpack CPES 20 mm CTS 630A 24kV; CTKS 630A 24kV

Operation
23 Verification of safe isolation from supply
DANGER
Hazardous voltage
Will cause death, serious injury or considerable property damage.
Verify safe isolation from supply.
➭ Possible sources of failure:
- Defective voltage indicator (or device for function testing of the coupling section)
- Maloperation of the voltage indicator (or device for function testing of the coupling
section)
➭ Test the function of the voltage indicator and the coupling section in accordance with
national standards:
- On a live panel
- With a test unit according to IEC 61243-5/EN 61243-5
- On all phases
➭ Use only voltage indicators or devices according to EN 61243-5 / IEC 61243-5 / VDE 0682-
415 to test the function of the coupling section. The interface conditions have not changed
as against the old standard VDE 0681 Part 7; the corresponding indicators can still be used.
➭ Perform repeat test of interface conditions at the capacitive interfaces, as well as on the
indicators according to the customer's specifications or national standards.
➭ Do not use short-circuiting jumpers as separate plugs. The function of the surge arrester
installed is not provided if short-circuiting jumpers are used.
INFORMATION
The following descriptions do not substitute reading the manufacturer documentation.
➭ Before using the voltage detecting systems, read the supplied manufacturer
documentation.
23.1 LRM plug-in sockets
① LRM voltage indicator

② Plug-in socket (interface phase L2)
③ Earthing socket (interface phase L2)
④ Cover
⑤ Documentation to repeat test of interface
condition
Fig. 167: LRM plug-in sockets
➭ Remove the covers from the plug-in sockets (interfaces of phases L1, L2 and L3).
➭ Insert the LRM voltage indicator consecutively into the plug-in sockets of the phases L1, L2
and L3.
✔ If the LRM voltage indicator does not flash or light up in any of the 3 phases, the phases are
not live.

Operation
➭ Refit the covers on the plug-in sockets.
Indication of LRM voltage indicator Description of the indication

Indication flashes Phase not isolated from supply
Indication lights up Phase not isolated from supply
No lighting up or flashing of the Phase isolated from supply

indication
The marking for documentation of the repeat test of the interface condition is located next to
the LRM plug-in sockets:
Fig. 168: Documentation to repeat test of interface condition

Operation
23.2 VOIS and CAPDIS indications
DANGER
Hazardous voltage
Will cause death, injury or property damage.
Only valid for voltage indicators CAPDIS-S1+/S2+.
➭ Do not modify the factory setting of the C2 module in the voltage detecting system
CAPDIS-S1+/S2+ except with consultation with the regional Siemens representative.
➭ If the setting of the C2 module was modified by mistake, re-establish the factory setting as
follows:
- Pull out the C2 module at the rear side of CAPDIS-S1+/S2+.
ATTENTION: Open printed circuit board may be energized.
- Plug the C2 module into CAPDIS-S1+/S2+ so that the marked arrow on the housing
points to the marking on the C2 module.
① Arrow
② Marking on the C2 module
③ C2 module
Fig. 169: Marking of the factory setting on

the C2 module (example)
① LC display
② "Test" button
③ Cover
④ Short instructions
⑤ Test socket L1
⑥ Earth socket
⑦ Test socket L2
⑧ Test socket L3
⑨ Duct for signaling
cables CAPDIS-M
Fig. 170: CAPDIS-S2+: Cover Fig. 171: CAPDIS-S2+: Cover

closed opened
① LC display
② Test socket L1
③ Test socket L2
④ Earth socket
⑤ Test socket L3
Fig. 172: VOIS+: Cover opened

Operation
Indicatio VOIS+, VOIS R+ CAPDIS-S1+ CAPDIS-S2+ Description of the indication

n
L1 L2 L3 L1 L2 L3 L1 L2 L3 State of the
relay contacts1
Red Green
A0 U ≠ 0 U=0 Operating voltage not present.
A1 U ≠ 0 U=0 Operating voltage present.
A2 U ≠ 0 U=0 • Operating voltage not present.

• Auxiliary voltage not available (only CAPDIS-S2+).
A3 U ≠ 0 U=0 Failure in phase L1, operating voltage at L2 and L3 (for

CAPDIS-Sx+ also earth-fault indication).
A4 - U ≠ 0 U=0 Voltage (not operating voltage) present.
A5 - U ≠ 0 U=0 Indication: "Test" passed (lights up shortly).
A6 - U ≠ 0 U=0 Indication: "Test" not passed (lights up shortly).
A7 - U ≠ 0 U=0 Overvoltage present (lights up permanently).
A8 - - U ≠ 0 U=0 Indication: "ERROR" e.g. in case of missing auxiliary voltage.
1
LED does not light up, LED lights up

Operation
23.3 WEGA indications
① LC display (illuminated for WEGA 2.2C)

② "Display Test" button
③ Test socket L1
④ Test socket L2
⑤ Earth socket
⑥ Test socket L3
Fig. 173: Operating elements WEGA 1.2C/

2.2C
Indication WEGA 1.2C WEGA 2.2C Description of the indication
L1 L2 L3 L1 L2 L3 State of the
relay contacts1
Red Green
A1 U ≠ 0 U=0 • Operating voltage present.

• Integrated repeat test passed.
A3 U ≠ 0 U=0 • Failure of the operating voltage at phase L1

• Operating voltage present at phases L2 and L3.
• Integrated repeat test passed (L2 and L3).
A4 U ≠ 0 U=0 • Voltage present, current monitoring of coupling section below limit
value.
A5 U ≠ 0 U=0 If "Display Test" button is pressed:

• Display test passed.
A6 U ≠ 0 U=0 In operation:
• Voltage present and integrated repeat test passed.
• Voltage signal too high.
A7 U ≠ 0 U=0 • Auxiliary voltage missing.
1
LED does not light up, LED lights up

Operation
24 Replacing HV HRC fuse-links

When a fuse-link or the shunt release of the three-position switch-disconnector has tripped, a
black-red bar (see page 195, "Protection tripping of the switch-fuse combination") is shown in
the position indicator.
For data to usable HV HRC fuse-links see page 61, "Selection of HV HRC fuse-links".
DANGER
Hazardous voltage.
➭ Isolate.
NOTICE
Stressed HV HRC fuse-links
When a HV HRC fuse-link has tripped, the HV HRC fuse-links in the two other phases may
also have been stressed.
➭ Replace the HV HRC fuse-links in all 3 phases.
Cable compartment cover of a panel with fuses:
Fig. 174: View from the front Fig. 175: View from the rear
Fig. 176: View from above
CAUTION
Explosion hazard due to internal arc
Can cause injury and property damage.
If panels with fuses are equipped with an incorrect cable compartment cover, the fuse slide
located inside the fuse box can detach and slip out.
➭ In panels with fuses, use the cable compartment cover intended for this purpose.

Operation
To unlock and remove the cable compartment cover, the three-position switch-disconnector
must be in EARTHED position. When the cable compartment cover is removed, mechanical
operation of the three-position switch-disconnector is blocked. Manual de-earthing is not
possible.
Motor operating With the cable compartment cover removed, the electrical power supply of the motor
mechanism operating mechanism is interrupted by an auxiliary switch located at the cable compartment
cover (optional).
Work operations
CAUTION
Risk of burning
Hot fuse-links can cause burns during replacement.
➭ Wear gloves.
➭ Let hot fuse-links cool down before replacing.
➭ Isolate and earth the cable feeder.

➭ Push the interlocking lever ① of the cable compartment cover ② upwards, lift the cable
compartment cover, and unhinge it.
➭ Withdraw the fuse slide with the HV HRC fuse-link.
① Sliding rail

Operation
Replacing HV HRC fuse- ➭ Pull the fixing bracket upwards and pull out the fuse.
links
CAUTION
Explosion hazard due to internal arc
Can cause injury and property damage.
The striker of a fuse-link installed the other way round cannot open the three-position switch-
disconnector in case of tripping.
➭ Insert fuse-links with the contact side of the striker into the contact of the handle.
➭ Fit new HV HRC fuse-link into the contact springs. The arrow on the HV HRC fuse-link must
point towards the cover of the fuse slide.
➭ Pull the retaining bracket upwards at the fuse slide and press the HV HRC fuse-link into the
mounting clips.
➭ Insert the fuse slide with the HV HRC fuse-link in the guide slot. The sliding rail ① must point
upwards.

Operation
➭ Push the fuse slide with the HV HRC fuse-link into the fuse box as far as it will go.
➭ Push the unlocking lever of the cable compartment cover upwards and refit the cable
compartment cover.
➭ Push the interlock of the cable compartment cover downwards.
➭ Fasten the cable compartment cover using bolts with cutting ring.
➭ De-earth the feeder.

Operation
25 Operating the feeder voltage transformer
25.1 Disconnecting the feeder voltage transformer
DANGER
Internal arcing and explosion hazard
When the panel is live, switching the voltage transformer disconnector can cause an internal
arc.
➭ Operate the voltage transformer disconnector only when the feeder is earthed.
Voltage transformers can be disconnected from the feeder and earthed via the voltage
transformer disconnector. The voltage transformer disconnector is located in the cable
compartment.
➭ Earth the feeder.
➭ Remove the cable compartment cover.
① Actuating opening for double-bit key

② Opening for padlock
③ Position indicator
Fig. 177: Voltage transformer disconnector
➭ Insert the double-bit key (5 mm diameter) into the actuating opening.

➭ Remove the padlock.
➭ Turn the double-bit key swiftly and continuously 180° counter-clockwise.
Fig. 178: Switching the voltage transformer disconnector to EARTHED position
✔ The position indicator shows the EARTHED position.

➭ Refit and lock the padlock.
➭ Remove the double-bit key.
✔ The voltage transformer is isolated from high-voltage, earthed, and secured against
reclosing.

Operation
25.2 Connecting the feeder voltage transformer
DANGER
Internal arcing and explosion hazard
When the panel is live, switching the voltage transformer disconnector can cause an internal
arc.
➭ Operate the voltage transformer disconnector only when the feeder is earthed.
To reconnect an earthed voltage transformer to the feeder, close the voltage transformer
disconnector again.
➭ Earth the feeder.
➭ Insert the double-bit key (5 mm diameter) into the actuating opening of the voltage
transformer disconnector.
➭ Remove the padlock from the voltage transformer disconnector.
Fig. 179: Switching the voltage transformer disconnector to CLOSED position
➭ Turn the double-bit key swiftly and continuously 180° clockwise.

✔ The position indicator of the voltage transformer disconnector shows the CLOSED position.
➭ Refit and lock the padlock.
➭ Remove the double-bit key.
➭ Hook the cable compartment cover in and fasten it with the fixing bolts.
✔ The voltage transformer disconnector is connected to high voltage and secured against
unauthorized opening.

Operation
26 Short instructions
INFORMATION
The short instructions in this section give just an overview of the sequence of switching
operations.
➭ Read the description of the control elements, and observe the instructions for the
switching operations and the warnings specified in there (see page 186, "Operation" and
following).
26.1 Operating circuit-breaker panels (600 mm panel width)
Circuit-breaker panel: Connecting the feeder to the busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the left and hold it
hold it. (the interrogation lever locks in lower
position. The actuating opening for the
DISCONNECTING function opens).
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To connect the feeder to the busbar, close
CLOSED position (insert the operating lever interrogation lever and the control gate the circuit-breaker.
and turn 90° clockwise). return to their initial position. The actuating
opening closes).

Operation
Circuit-breaker panel: Disconnecting the feeder from the busbar
1 2 3
Initial situation ➭ To disconnect the feeder from the busbar, ➭ Push the interrogation lever downwards and hold
open the circuit-breaker. it.
4 5 6
➭ Push the control gate to the left and ➭ Switch the three-position disconnector to ➭ Remove the operating lever (the interrogation
hold it (the interrogation lever locks in OPEN position (insert the operating lever lever and the control gate return to their initial
lower position. The actuating opening and turn 90° counter-clockwise). position. The actuating opening closes).
for the DISCONNECTING function
opens).

Operation
Circuit-breaker panel: Earthing the feeder
NOTICE
1 2 3 4
Initial situation ➭ Push the interrogation lever ➭ Push the control gate to the ➭ Switch the three-position
downwards and hold it. right (the interrogation lever disconnector to READY-TO-
locks in lower position. The EARTH position (insert the
actuating opening for the operating lever and turn 90°
READY-TO-EARTH function clockwise).
opens).
5 6 7 8
➭ Remove the operating lever ➭ To earth the feeder, close the ➭ Push the locking device ➭ Fit a padlock.
(the interrogation lever and the circuit-breaker. upwards.
control gate return to their
initial position. The actuating
opening closes).

Operation
Circuit-breaker panel: De-earthing the feeder
1 2 3 4
Initial situation ➭ Remove the padlock (the ➭ To de-earth the feeder, open ➭ Push the interrogation lever
locking device goes down). the circuit-breaker. downwards and hold it.
5 6 7
➭ Push the control gate to the ➭ Switch the three-position ➭ Remove the operating lever
right and hold it (the disconnector from READY-TO- (the interrogation lever and the
interrogation lever locks in EARTH to OPEN position (insert control gate return to their
lower position. The actuating the operating lever and turn initial position).
opening for the READY-TO- 90° counter-clockwise).
EARTH function opens).

Operation
Circuit-breaker panel: Earthing the feeder with forced sequence circuit
1 2 3
Initial situation ➭ Push the control gate to the right and ➭ Switch the three-position disconnector to READY-TO-
hold it (the actuating opening for the EARTH position (insert the operating lever and turn
READY-TO-EARTH function opens). 90° clockwise).
The circuit-breaker closes automatically (time relay
adjustable; factory setting: 1 s).
The feeder is earthed.
4 5
➭ Remove the operating lever (the ➭ Push the locking device upwards and fit
control gate returns to its initial a padlock.
position).

Operation
Circuit-breaker panel: De-earthing the feeder with forced sequence circuit
1 2 3
Initial situation ➭ Remove the padlock (the locking device ➭ Push the control gate to the right and hold
goes down). it.
4 5
➭ Switch the three-position disconnector from ➭ Remove the operating lever (the control
READY-TO-EARTH to OPEN position (turn gate returns to its initial position).
operating lever 90° counter-clockwise).The
circuit-breaker opens automatically
before the three-position disconnector
opens.

Operation
26.2 Operating circuit breaker panels (900 mm panel width)
Circuit-breaker panel: Connecting the feeder to the busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the left and hold it
and hold it. (the interrogation lever locks in lower
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To connect the feeder to the busbar, close
CLOSED position (insert the operating lever interrogation lever and the control gate the circuit-breaker.
and turn 90° clockwise). return to their initial position. The actuating
opening closes).

Operation
Circuit-breaker panel: Disconnecting the feeder from the busbar
1 2 3
Initial situation ➭ To de-earth the feeder, open the circuit- ➭ Push the interrogation lever downwards
breaker. and hold it.
4 5 6
➭ Push the control gate to the left and hold it ➭ Switch the three-position disconnector to ➭ Remove the operating lever (the
(the interrogation lever locks in lower OPEN position (insert the operating lever interrogation lever and the control gate
position. The actuating opening for the and turn 180° counter-clockwise). return to their initial position. The
DISCONNECTING function opens). actuating opening closes).

Operation
Circuit-breaker panel: Earthing the feeder
NOTICE
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the right and hold
and hold it. it (the interrogation lever locks in lower
READY-TO-EARTH function opens).
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To earth the feeder, close the circuit-
READY-TO-EARTH position (insert the operating interrogation lever and the control gate breaker.
lever and turn 180° clockwise). return to their initial position. The
actuating opening closes).
7 8
➭ Push the locking device upwards. ➭ Fit a padlock.

Operation
Circuit-breaker panel: De-earthing the feeder
1 2 3
Initial situation
➭ Remove the padlock (the locking device ➭ To de-earth the feeder, open the circuit-
goes down). breaker.
4 5 6
➭ Switch the three-position disconnector

➭ Push the interrogation lever downwards. ➭ Push the control gate to the right and hold
from READY-TO-EARTH to OPEN position
it (the interrogation lever locks in lower
(insert the operating lever and turn 180°
counter-clockwise).
7
➭ Remove the operating lever (the

interrogation lever and the control gate
return to their initial position. The actuating
opening closes).

Operation
Circuit-breaker panel: Earthing the feeder with forced sequence circuit
1 2 3
Initial situation ➭ Push the control gate to the right and hold ➭ Switch the three-position disconnector to
it. READY-TO-EARTH position (insert the
operating lever and turn 180° clockwise).
The circuit-breaker closes automatically
(time relay adjustable; factory setting:
1 s). The feeder is earthed.
4 5
➭ Remove the operating lever (the control gate ➭ Push the locking device upwards and fit a
returns to its initial position). padlock.

Operation
Circuit-breaker panel: De-earthing the feeder with forced sequence circuit
1 2 3
Initial situation
➭ Remove the padlock (the locking device goes
down).
➭ Push the control gate to the right and hold it
(the actuating opening for the READY-TO-
4 5
➭ Switch the three-position disconnector ➭ Remove the operating lever (the control gate
from READY-TO-EARTH to OPEN position returns to its initial position. The actuating
(turn operating lever 180° counter- opening closes).
clockwise).
The circuit-breaker opens
automatically before the three-
position disconnector opens.

Operation
26.3 Operating vacuum contactor panels
Vacuum contactor panel: Connecting the feeder to the busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the left (the
hold it. interrogation lever locks in lower position.
The actuating opening for the
4 5 6
➭ Switch the three-position switch- ➭ Remove the operating lever (the ➭ To connect the feeder to the busbar, close
disconnector to CLOSED position (insert the interrogation lever and the control gate the contactor via a bay controller (e.g.
operating lever and turn 90° clockwise). return to their initial position. The actuating SIPROTEC).
opening closes).

Operation
Vacuum contactor panel: Disconnecting the feeder from the busbar
1 2 3
Initial situation ➭ To disconnect the feeder from the busbar, ➭ Push the interrogation lever downwards and
open the contactor with the pushbutton. hold it.
4 5 6
➭ Push the control gate to the left (the ➭ Switch the three-position switch- ➭ Remove the operating lever (the
interrogation lever locks in lower position. disconnector to OPEN position (insert the interrogation lever and the control gate
The actuating opening for the operating lever and turn 90° counter- return to their initial position. The actuating
DISCONNECTING function opens). clockwise). opening closes).

Operation
Vacuum contactor panel: Earthing the feeder
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the right (the
and hold it. interrogation lever locks in lower position.
The actuating opening for the EARTHING
function opens).
4 5
➭ Switch the three-position switch- ➭ Remove the operating lever (the

disconnector to EARTHED position (insert interrogation lever and the control gate
the operating lever and turn 90° clockwise). return to their initial position. The actuating
opening closes).

Operation
Vacuum contactor panel: De-earthing the feeder
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the right (the
function opens).
4 5

disconnector from EARTHED to OPEN interrogation lever and the control gate
position (insert the operating lever and turn return to their initial position. The actuating
90° counter-clockwise). opening closes).

Operation
26.4 Operating switch-disconnector, disconnector, ring-main and metering

panels with 600 mm panel width
Switch-disconnector, disconnector, ring-main or metering panels: Connecting the

feeder to the busbar
1 2 3
Initial situation ➭ Push the interrogation lever ➭ Push the control gate to the left.
downwards.
4 5

disconnector to CLOSED position (insert the interrogation lever and the control gate
operating lever and turn 90° clockwise). return to their initial position).

Operation
Switch-disconnector, disconnector, ring-main or metering panels: Disconnecting the

feeder from the busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the left (the
4 5

disconnector to OPEN position (insert the interrogation lever and the control gate
operating lever and turn 90° counter- return to their initial position).
clockwise).

Operation
Switch-disconnector, disconnector, ring-main or metering panels:

Earthing the feeder
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the right (the
function opens).
4 5

disconnector to EARTHED position (insert interrogation lever and the control gate
the operating lever and turn 90° clockwise). return to their initial position).

Operation
Switch-disconnector, disconnector, ring-main or metering panels:

De-earthing the feeder
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the right.
hold it.
4 5

disconnector from EARTHED to OPEN interrogation lever and the control gate
position (insert the operating lever and turn return to their initial position).
90° counter-clockwise).

Operation
26.5 Operating disconnector panels as of 2000 A (900 mm panel width)
Disconnector panel as of 2000 A: Connecting the feeder to the busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the left.
and hold it.
4 5
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the

CLOSED position (insert the operating lever and interrogation lever and the control gate
turn 180° clockwise). return to their initial position).

Operation
Disconnector panel as of 2000 A: Disconnecting the feeder from the busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the left.
hold it.
4 5
➭ Switch the three-position disconnector ➭ Remove the operating lever (the

to OPEN position (insert the operating interrogation lever and the control gate
lever and turn 180° counter-clockwise). return to their initial position).

Operation
Disconnector panel as of 2000 A: Earthing the feeder
1 2 3

Initial situation ➭ Push the interrogation lever downwards and
hold it.
4 5
➭ Switch the three-position disconnector to

EARTHED position (insert the operating lever
and turn 180° clockwise).
return to their initial position).

Operation
Disconnector panel as of 2000 A: De-earthing the feeder
1 2 3
➭ Push the interrogation lever downwards and ➭ Push the control gate to the right.
Initial situation
hold it.
4 5
➭ Switch the three-position disconnector from

EARTHED to OPEN position (insert the
operating lever and turn 90° counter-
clockwise).

Operation
26.6 Operating bus sectionalizer panels with 600 mm panel width
Bus sectionalizer panel with one three-position disconnector: Coupling the busbars
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the left and hold it
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To couple the busbars, close the circuit-
CLOSED position (insert the operating lever and interrogation lever and the control gate breaker.
turn 90° clockwise). return to their initial position).

Operation
Bus sectionalizer panel with one three-position disconnector: Decoupling the

busbars
1 2 3
Initial situation ➭ To decouple the busbars, open the circuit- ➭ Push the interrogation lever downwards
4 5 6
position. The actuating opening for the and turn 90° counter-clockwise). return to their initial position).

Operation
Bus sectionalizer panel with one three-position disconnector: Earthing the right-
hand busbar
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the right and hold it
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To earth the busbar system, close the
READY-TO-EARTH position (insert the interrogation lever and the control gate circuit-breaker.
7 8

Operation
Bus sectionalizer panel with one three-position disconnector: De-earthing the right-
hand busbar system
1 2 3
Initial situation ➭ Remove the padlock (the locking device goes ➭ To de-earth the busbar system, open the
down). circuit-breaker.
4 5 6
➭ Push the interrogation lever downwards ➭ Push the control gate to the right and hold it ➭ Switch the three-position disconnector from
and hold it. (the interrogation lever locks in lower READY-TO-EARTH to OPEN position (insert the
position. The actuating opening for the operating lever and turn 90° counter-
READY-TO-EARTH function opens). clockwise).
7


Operation
26.7 Operating bus sectionalizer panels with 900 mm panel width
Bus sectionalizer panel with one three-position disconnector: Coupling the busbars
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the control gate to the left (the
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To couple the busbars, close the circuit-
CLOSED position (insert the operating lever interrogation lever and the control gate breaker.
and turn 180° clockwise). return to their initial position).

Operation
Bus sectionalizer panel with one three-position disconnector: Decoupling the

busbars
1 2 3
Initial situation ➭ To decouple the busbars, open the circuit- ➭ Push the interrogation lever downwards
4 5 6
position and the actuating opening for the and turn 180° counter-clockwise). return to their initial position).

Operation
Bus sectionalizer panel with one three-position disconnector: Earthing the right-
hand busbar
1 2 3
➭ Initial situation ➭ Push the interrogation lever downwards and ➭ Push the control gate to the right and hold it
hold it. (the interrogation lever locks in lower
4 5 6
➭ Switch the three-position disconnector to ➭ Remove the operating lever (the ➭ To earth the busbar system, close the circuit-
READY-TO-EARTH position (insert the interrogation lever and the control gate breaker.
7 8

Operation
Bus sectionalizer panel with one three-position disconnector: De-earthing the right-
hand busbar system
1 2 3
Initial situation ➭ Remove the padlock (the locking device ➭ To de-earth the busbar system, open the
goes down). circuit-breaker.
4 5 6
➭ Push the interrogation lever downwards and ➭ Push the control gate to the right and hold it ➭ Switch the three-position disconnector from
hold it. (the interrogation lever locks in lower READY-TO-EARTH to OPEN position (insert
position. The actuating opening for the the operating lever and turn 180° counter-
READY-TO-EARTH function opens). clockwise).
7


Operation
26.8 Operating bus sectionalizer panels with two three-position disconnectors

and with 600 mm panel width
Bus sectionalizer panel with two three-position disconnectors: Coupling the busbars
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the left
and hold it. and hold it (the interrogation lever locks in
lower position. The left-hand actuating
opening for the DISCONNECTING function
opens).
4 5 6
➭ Switch the left-hand three-position ➭ Remove the operating lever (the ➭ Push the interrogation lever downwards
disconnector to CLOSED position (insert the interrogation lever and the control gate again and hold it.

Operation
7 8 9
➭ Push the right-hand control gate to the left ➭ Switch the right-hand three-position ➭ Remove the operating lever (the
(the interrogation lever locks in lower position. disconnector to CLOSED position (insert interrogation lever and the control gate
The right-hand actuating opening for the the operating lever and turn 90° return to their initial position).
DISCONNECTING function opens). clockwise).
10
➭ To couple the busbars, close the circuit-

breaker.
Bus sectionalizer panel with two three-position disconnectors: Decoupling the

busbars
1 2 3
Initial situation ➭ To decouple the busbars, open the circuit- ➭ Push the interrogation lever downwards and
breaker. hold it.
4 5 6
➭ Push the left-hand control gate to the left ➭ Switch the left-hand three-position ➭ Remove the operating lever (the
(the interrogation lever locks in lower disconnector to OPEN position (insert the interrogation lever and the control gate
position. The left-hand actuating opening operating lever and turn 90° counter- return to their initial position).
for the DISCONNECTING function opens). clockwise).

Operation
7 8 9
➭ Push the interrogation lever downwards ➭ Push the right-hand control gate to the left ➭ Switch the right-hand three-position
again and hold it. and hold it (the interrogation lever locks in disconnector to OPEN position (insert the
lower position. The right-hand actuating operating lever and turn 90° counter-
opening for the DISCONNECTING function clockwise).
opens).
10


Operation
Bus sectionalizer panel with two three-position disconnectors: Earthing the left-hand
busbar system
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the left
opens).
4 5 6
disconnector to CLOSED position (insert the interrogation lever and the control gate again and hold it.
7 8 9
➭ Push the right-hand control gate to the ➭ Switch the right-hand three-position ➭ Remove the operating lever (the
right (the interrogation lever locks in lower disconnector to READY-TO-EARTH position interrogation lever and the control gate
position. The right-hand actuating opening (insert the operating lever and turn 90° return to their initial position).
for the READY-TO-EARTH function opens). clockwise).
10 11
➭ To earth the left-hand busbar system, close ➭ Fit a padlock.

the circuit-breaker.

Operation
Bus sectionalizer panel with two three-position disconnectors: De-earthing the left-
hand busbar system
1 2 3
Initial situation ➭ Remove the padlock (the locking device goes ➭ To de-earth the busbar system, open the
down). circuit-breaker.
4 5 6
➭ Push the interrogation lever downwards ➭ Push the right-hand control gate to the right ➭ Switch the right-hand three-position
and hold it. (the interrogation lever locks in lower disconnector from READY-TO-EARTH to
position. The right-hand actuating opening OPEN position (insert the operating lever
for the READY-TO-EARTH function opens). and turn 90° counter-clockwise).
7 8 9
➭ Remove the operating lever (the ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the left
interrogation lever and the control gate again and hold it. (the interrogation lever locks in lower
return to their initial position). position. The left-hand actuating opening for
the DISCONNECTING function opens).
10 11
➭ Switch the left-hand three-position ➭ Remove the operating lever (the

disconnector to OPEN position (insert the interrogation lever and the control gate
operating lever and turn 90° counter- return to their initial position).
clockwise).

Operation
Bus sectionalizer panel with two three-position disconnectors: Earthing the right-
hand busbar system
1 2 3
Initial situation ➭ Push the interrogation lever downwards and ➭ Push the right-hand control gate to the left
hold it. and hold it (the interrogation lever locks in
lower position. The right-hand actuating
opens).
4 5 6
➭ Switch the right-hand three-position ➭ Remove the operating lever (the interrogation ➭ Push the interrogation lever downwards
disconnector to CLOSED position (insert lever and the control gate return to their initial again and hold it.
the operating lever and turn 90° position).
clockwise).
7 8 9
➭ Push the left-hand control gate to the ➭ Switch the left-hand three-position ➭ Remove the operating lever (the
right and hold it (the interrogation lever disconnector to READY-TO-EARTH position interrogation lever and the control gate
locks in lower position. The left-hand (insert the operating lever and turn 90° return to their initial position).
actuating opening for the READY-TO- clockwise).
10 11
➭ To earth the right-hand busbar system, ➭ Fit a padlock.

close the circuit-breaker.

Operation
Bus sectionalizer panel with two three-position disconnectors: De-earthing the right-
hand busbar system
1 2 3
Initial situation ➭ Remove the padlock (the locking device ➭ To de-earth the busbar system, open the
goes down). circuit-breaker.
4 5 6
➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the right ➭ Switch the left-hand three-position
and hold it. and hold it (the interrogation lever locks in disconnector from READY-TO-EARTH to OPEN
lower position. The left-hand actuating position (insert the operating lever and turn
opening for the READY-TO-EARTH function 90° counter-clockwise).
opens).
7 8 9
➭ Remove the operating lever (the ➭ Push the interrogation lever downwards ➭ Push the right-hand control gate to the left
interrogation lever and the control gate again and hold it. and hold it (the interrogation lever locks in
return to their initial position). lower position. The right-hand actuating
opens).
10 11
➭ Switch the right-hand three-position ➭ Remove the operating lever (the

disconnector to OPEN position. interrogation lever and the control gate

Operation
26.9 Operating bus sectionalizer panels with two three-position disconnectors

and with 900 mm panel width
Bus sectionalizer panel with two three-position disconnectors: Coupling the busbars
1 2
Initial situation ➭ Push the interrogation lever downwards and hold it.
3 4
➭ Push the control gate to the left and hold it (the interrogation lever ➭ Switch the left-hand three-position disconnector to CLOSED position
locks in lower position. The actuating opening for the (insert the operating lever and turn 180° clockwise).
5 6
➭ Remove the operating lever (the interrogation lever and the control ➭ Push the interrogation lever downwards and hold it.
gate return to their initial position. The actuating opening closes).

Operation
7 8
➭ Push the right-hand control gate to the left and hold it (the ➭ Switch the right-hand three-position disconnector to CLOSED position
interrogation lever locks in lower position. The actuating opening for (insert the operating lever and turn 180° clockwise).
9 10
➭ Remove the operating lever (the interrogation lever and the control ➭ To couple the busbars, close the circuit-breaker.
gate return to their initial position. The actuating opening closes).

Operation
Bus sectionalizer panel with two three-position disconnectors: Decoupling the

busbars
1 2
Initial situation ➭ To decouple the busbars, open the circuit-breaker.

3 4
➭ Push the interrogation lever downwards and hold it. ➭ Push the left-hand control gate to the left and hold it (the
interrogation lever locks in lower position. The left-hand actuating
opening for the DISCONNECTING function opens).
5 6
➭ Switch the left-hand three-position disconnector to OPEN position ➭ Remove the operating lever (the interrogation lever and the control
(insert the operating lever and turn 180° counter-clockwise). gate return to their initial position).
7 8
➭ Push the interrogation lever downwards again and hold it. ➭ Push the right-hand control gate to the left and hold it (the
interrogation lever locks in lower position. The right-hand actuating
9 10
➭ Switch the right-hand three-position disconnector to OPEN position ➭ Remove the operating lever (the interrogation lever and the control
(insert the operating lever and turn 180° counter-clockwise). gate return to their initial position).

Operation
Bus sectionalizer panel with two three-position disconnectors: Earthing the left-hand
busbar system
1 2
3 4
➭ Push the left-hand control gate to the left and hold it (the ➭ Switch the left-hand three-position disconnector to CLOSED position
interrogation lever locks in lower position. The left-hand actuating (insert the operating lever and turn 180° clockwise).
5 6
➭ Remove the operating lever (the interrogation lever and the control ➭ Push the interrogation lever downwards again and hold it.
gate return to their initial position).
7 8
➭ Push the right-hand control gate to the right and hold it (the ➭ Switch the right-hand three-position disconnector to READY-TO-
interrogation lever locks in lower position. The right-hand actuating EARTH position (insert the operating lever and turn 180° clockwise).
opening for the READY-TO-EARTH function opens).

Operation
9 10
➭ Remove the operating lever (the interrogation lever and the control ➭ To earth the left-hand busbar system, close the circuit-breaker.
11
➭ Fit a padlock.
Bus sectionalizer panel with two three-position disconnectors: De-earthing the left-
hand busbar system
1 2
Initial situation ➭ Remove the padlock (the locking device goes down).
3 4
➭ To de-earth the busbar system, open the circuit-breaker. ➭ Push the interrogation lever downwards and hold it.
5 6
➭ Push the right-hand control gate to the right and hold it (the ➭ Switch the right-hand three-position disconnector from READY-TO-
interrogation lever locks in lower position. The right-hand actuating EARTH to OPEN position (insert the operating lever and turn 180°
opening for the READY-TO-EARTH function opens). counter-clockwise).

Operation
7 8
9 10
➭ Push the left-hand control gate to the left and hold it (the ➭ Switch the left-hand three-position disconnector to OPEN position
interrogation lever locks in lower position. The left-hand actuating (insert the operating lever and turn 180° counter-clockwise).
11
➭ Remove the operating lever (the interrogation lever and the control
Bus sectionalizer panel with two three-position disconnectors: Earthing the right-
hand busbar system
1 2
3 4
➭ Push the right-hand control gate to the left and hold it (the ➭ Switch the right-hand three-position disconnector to CLOSED position
interrogation lever locks in lower position. The right-hand actuating (insert the operating lever and turn 180° clockwise).

Operation
5 6
7 8
➭ Push the left-hand control gate to the right and hold it (the ➭ Switch the left-hand three-position disconnector to READY-TO-EARTH
interrogation lever locks in lower position. The left-hand actuating position (insert the operating lever and turn 180° clockwise).
opening for the READY-TO-EARTH function opens).
9 10
➭ Remove the operating lever (the interrogation lever and the control ➭ To earth the right-hand busbar system, close the circuit-breaker.
11
➭ Fit a padlock.

Operation
Bus sectionalizer panel with two three-position disconnectors: De-earthing the right-
hand busbar system
1 2
Initial situation ➭ Remove the padlock (the locking device goes down).
3 4
➭ To de-earth the busbar system, open the circuit-breaker. ➭ Push the interrogation lever downwards and hold it.
5 6
➭ Push the left-hand control gate to the right and hold it (the ➭ Switch the left-hand three-position disconnector from READY-TO-
interrogation lever locks in lower position. The left-hand actuating EARTH to OPEN position (insert the operating lever and turn 180°
opening for the READY-TO-EARTH function opens). counter-clockwise).
7 8

Operation
9 10
➭ Push the right-hand control gate to the left and hold it (the ➭ Switch the right-hand three-position disconnector to OPEN position.
interrogation lever locks in lower position. The right-hand actuating
11
➭ Remove the operating lever (the interrogation lever and the control
26.10 Operating the circuit-breaker panel with busbar earthing switch
Earthing the busbar system
1 2 3
Initial situation ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the right
opening for the READY-TO-EARTH function
opens).
4 5 6
➭ Switch the left-hand three-position ➭ Remove the operating lever (the ➭ To earth the feeder, close the circuit-
disconnector to READY-TO-EARTH position interrogation lever and the control gate breaker.
(insert the operating lever and turn 90° return to their initial position).
clockwise).

Operation
7 8 9
➭ Push the right-hand control gate to the right ➭ Switch the right-hand three-position ➭ Remove the operating lever (the control
(the right-hand actuating opening for the disconnector to READY-TO-EARTH position gate returns to its initial position).
EARTHING function opens). (insert the operating lever and turn 90°
clockwise).
10 11 12
➭ Open the circuit-breaker (the feeder is ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the right
earthed through the right-hand three- again and hold it. and hold it (the interrogation lever locks in
position disconnector). lower position. The left-hand actuating
opens).
13 14 15
disconnector from READY-TO-EARTH to interrogation lever and the control gate again and hold it.
OPEN position (insert the operating lever return to their initial position).
and turn 90° counter-clockwise).

Operation
16 17 18
➭ Push the left-hand control gate to the left ➭ Switch the left-hand three-position ➭ Remove the operating lever (the
and hold it (the interrogation lever locks in disconnector to CLOSED position (insert the interrogation lever and the control gate
lower position. The actuating opening for operating lever and turn 90° clockwise). return to their initial position).
19 20
➭ To earth the busbar system, close the ➭ Fit a padlock.

circuit-breaker.
De-earthing the busbar system
1 2 3
Initial situation ➭ Remove the padlock. ➭ To de-earth the busbar system, open the
circuit-breaker.
4 5 6
➭ Push the interrogation lever downwards and ➭ Push the left-hand control gate to the left ➭ Switch the left-hand three-position
hold it. and hold it (the interrogation lever locks in disconnector to OPEN position (insert the
lower position. The actuating opening for operating lever and turn 90° counter-
the DISCONNECTING function opens). clockwise).

Operation
7 8 9
➭ Remove the operating lever (the ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the right
interrogation lever and the control gate again and hold it. and hold it (the interrogation lever locks in
return to their initial position). lower position. The left-hand actuating
opens).
10 11 12
➭ Switch the left-hand three-position ➭ Remove the operating lever (the ➭ Close the circuit-breaker (the feeder is
disconnector to READY-TO-EARTH position interrogation lever and the control gate earthed through the left-hand three-
(insert the operating lever and turn 90° return to their initial position). position disconnector).
clockwise).
13 14 15
➭ Push the right-hand control gate to the right ➭ Switch the right-hand three-position ➭ Remove the operating lever (the control
and hold it. disconnector from READY-TO-EARTH to gate returns to its initial position).
OPEN position (insert the operating lever
and turn 90° counter-clockwise). The feeder
remains earthed through the left-hand
three-position disconnector.

Operation
16 17 18
➭ To de-earth the feeder, open the circuit- ➭ Push the interrogation lever downwards ➭ Push the left-hand control gate to the right
breaker. again and hold it. and hold it (the interrogation lever locks in
opens).
19 20
➭ Switch the left-hand three-position ➭ Remove the operating lever (the

disconnector from READY-TO-EARTH to OPEN interrogation lever and the control gate
position (insert the operating lever and turn return to their initial position).
90° counter-clockwise).

Operation
27 Cable testing
DANGER
High voltage and explosion hazard
Will cause serious injury and damage the voltage transformer. If the voltage transformer
disconnector is closed, the test voltage can destroy the voltage transformer.
➭ Switch the voltage transformer disconnector to EARTHED position before testing the
cables, and secure it.
WARNING
Cable testing involves hazardous voltages.
Can cause death, serious injury and property damage.
Incorrect cable testing can damage the switchgear.
➭ During the cable test, keep a safety distance (min. 3 m) from the switchgear.
➭ Install barriers.
➭ Switch on warnings.
➭ When the cable test is completed, earth the test cables.
NOTICE
Voltage indicators may be damaged by test voltage during cable tests.
May cause property damage.
➭ Short-circuit the voltage indicators with short-circuit plugs at the earthing points of the test
sockets.
Short-circuit plug, make Kries, order number 2500029 Short-circuit plug, make Horstmann, order number 51-
9904-001
Preconditions • Circuit-breaker in OPEN position.

• Three-position switch in OPEN position.
• Voltage transformer disconnector in EARTHED position (see page 212, "Operating the feeder
voltage transformer").

Operation
Test voltages
Rated voltage of the DC test voltage AC test voltage VLF1 0.1 Hz

switchgear [kV]
AC DC Rectangle [kV] Sinus [kV] Test
duration
Uct [kV] Test Uct [kV] Test Mean value Maximum Mean value Maximum
[min]
duration duration value value
[min] [min]
7.2 11 1 22 15 22 22 15.6 22 60
12 19 1 38 15 38 38 26.8 38 60
15 28 1 52 15 52 52 36.8 52 60
17.5 28 1 52 15 52 52 36.8 52 60
24 38 1 72 15 72 72 51 72 60
1
Very low frequency
Test adapters Suitable test adapters must be available for performing the cable test. The following table
offers an overview of the test adapters of the individual cable T-plug manufacturers:
Make Test adapter For cable T-plugs

3M PR 23.2 93-EE 705-6
93-EE 715-6
Nexans Euromold 400TR 400TB/G; 430TB-630A; 300PB-630A; 440TB/G
K400TB/G; K430TB-630A; K300PB-630A; K440TB/G
800TR 484TB/G; 804PB/G
489TB/G; 809PB/G
K484TB/G; K804PB/G
K489TB/G; K809PB/G
nkt cables PAK 630 M12 CB 12-630; CC 12-630
CB 17.5-630; CC 17.5-630
CB 24-630; CC 24-630
CB 24-1250-2; CC 24-1250-2
PAK 630 M16 CB 36-630(1250); CC 36-630(1250)
CB 42-1250-3, CC 42-2500-3
Südkabel PR 23.1 SET 12; SEHDT 13; SEHDK 13.1
SET 24; SEHDT 23; SEHDK 23.1
Tyco Electronics Raychem RSTI-68TR RSTI-58xx; RSTI-CC-58xx
RSTI-68TRL RSTI-395x; RSTI-CC-395x; RSTI-595x; RSTI-CC-595x
GCA CJB10-TB CJBxx-630; CJBKxx-630
ABB Kabeldon PG-A 630 CSE-A xx630-xx
Cellpack CPS CTS 630A 24kV; CTKS 630A 24kV
Performing the cable test ➭ Earth the feeder (see page 194, "Earthing/ready-to-earth with the three-position switch").
➭ Verify safe isolation from supply (see page 203, "Verification of safe isolation from supply").
➭ Disconnect the feeder in the opposite substation and secure against reclosing.
➭ Verify safe isolation from supply in the opposite substation.
➭ Remove the screw insert of the connected cable T-plug according to the manufacturer's
instructions.
➭ Insert/screw the test adapter into the cable T-plug.
➭ Connect test lead.
➭ Short-circuit the voltage indicators at the earthing points of the test sockets using short-
circuit plugs.
➭ De-earth the feeder (see page 194, "De-earthing with the three-position switch").
➭ Perform voltage test. Perform the test according to the recommendations of the cable
manufacturers or the customers' specifications.
➭ Proceed in reverse order to return to the initial situation.

Service information
Service information
28 Maintenance
Under normal operating conditions, the fixed-mounted circuit-breaker switchgear NXPLUS C,
the vacuum circuit-breaker 3AH55 and the vacuum contactor 3TL7 are maintenance-free.
The switchgear vessel represents a hermetically sealed pressure system according to
IEC 62271-200. Maintenance of the insulation filling is not required.
Secondary equipment Inspection/testing of the secondary equipment such as the capacitive voltage detecting
system is done within the scope of national standards and customer-specific regulations.
Checking the dew point The dew point needs no checking throughout the entire service life.
Replacement of Due to the fact that all parts of this switchgear type have been optimized to last the normal
components service life, it is not possible to recommend particular spare parts.
Checking the gas quality The gas quality needs no checking throughout the service life.
28.1 Maintenance of circuit-breaker 3AH25 with 30000 operating cycles

The 3AH25 circuit-breaker with 30,000 operating cycles must be lubricated after 10,000 and
20,000 operating cycles.
Permissible lubricants:
• Isoflex Topas L 32
• Tellus Oil 32
For suppliers and manufacturer information of lubricants: see page 284, "Permissible
lubricants".
Auxiliary means
• Thin brush (length: min. 30 cm)
• Oil can with a thin outlet with a length of 30 cm as a minimum
• 2 cable straps
• Battery screwdriver or hexalobular socket screwdriver (Torx)
DANGER
Hazardous voltage.
➭ Isolate.

Service information
WARNING
been performed:
- Trip the MCB.
instructions:
➭ Disassemble and remove the front cover of the panel.
Removing the To reach all lubrication points, the interlocking must be removed:
interlocking
① Bolt, left side
② Bolted joint
③ Cable strap (2x)
④ Bolt, right side
➭ Undo bolts ① and ④ . Store the bolts carefully.

➭ Remove 2 cable straps ③ .
➭ Undo the bolted joint ② . Store the components carefully.
➭ Carefully remove the interlocking from the operating mechanism. Store the interlocking
protected against dirt.
✔ The operating mechanism is ready to maintenance.

Service information
Lubrication chart for 3AH25
Fig. 180: Lubrication chart overview for operating mechanism 3AH25
WARNING
Charged operating springs
To lubricate some components, the operating springs must be charged.
➭ Do not reach into the operating mechanism compartment with your hands.
➭ Apply lubricant with a long brush.
➭ The operating springs must be uncharged after lubrication.
Detail view Component Lubricants

① Apply grease to the crank pins for Isoflex Topas L32
pushbutton operation.
② Apply grease to the pushbutton Isoflex Topas L32
actuating plate.
① Apply grease to the closing and opening Isoflex Topas L32

latch.
② Apply grease to the curve contour. Isoflex Topas L32
③ Oil the bearing for the deflection lever. Shell Tellus Oil S2M32

Service information

① Apply grease to the guide of the opening Isoflex Topas L32
spring.
Precondition: Opening spring charged.
WARNING: Do not reach into the
operating mechanism compartment
with your hands when the operating
springs are charged.
② Oil the stud connections. Shell Tellus Oil S2M32
③ Oil the elongated hole. Shell Tellus Oil S2M32
④ Oil the bearing of the opening spring. Shell Tellus Oil S2M32
⑤ Oil the stud connections. Shell Tellus Oil S2M32
① Oil the shaft of the auxiliary switch on Shell Tellus Oil S2M32
both sides.
① Apply grease to the deflection of the Isoflex Topas L32

auxiliary switch.
① Apply grease to the contact surface Isoflex Topas L32

between release and bolt.
② Oil the contact surfaces between second/ Shell Tellus Oil S2M32
third release and bolt connections.
① Apply grease to the plunger at the Isoflex Topas L32

operating solenoid.

Service information

① Apply grease to the roller or latch. Isoflex Topas L32
② Oil the stud connections. Shell Tellus Oil S2M32
③ Apply grease to the opening latch. Isoflex Topas L32
④ Apply grease to the curve of the opening Isoflex Topas L32
latch.
① Oil the bearing for the operating shaft. Shell Tellus Oil S2M32
② Apply grease to the deflection of the Isoflex Topas L32
auxiliary switch.
③ Apply grease to the end stop. Isoflex Topas L32
① Oil the stud connection. Shell Tellus Oil S2M32

② Apply grease to the bearing of the Isoflex Topas L32
contact pressure spring.
① Apply grease to the dashpot. Isoflex Topas L32



Service information

① Oil the bearing for the operating shaft. Shell Tellus Oil S2M32
① Apply grease to the guide of the closing Isoflex Topas L32

spring.
Precondition: Closing spring charged.
WARNING: Do not reach into the
operating mechanism compartment
with your hands when the operating
springs are charged.
Mounting the interlock ➭ Carefully thread the interlocking into the operating mechanism. Insert the lug ③ into the
driver at the top, and the tripping rocker ④ into the slide ⑤ .
① Bolt, left side

② Bolted joint
③ Lug
④ Tripping rocker
⑤ Slide
⑥ Cable strap (2x)
⑦ Bolt, right side
➭ Fasten bolts ① and ⑦ (both M6x12 with hexalobular socket)

➭ Tighten the rocker ④ with the bolted joint ② .
➭ Fix the cables ⑥ again with 2 cable straps.
➭ Refit the front cover of the panel.
➭ Test proper functioning of the interlock according to the following table. All control
elements must be easy to operate.

Service information
Checking the interlocking conditions
Switch positions of the three- Switch position of Interlocking condition

position disconnector the circuit-breaker
DISCONNE READY-TO-EARTH
CTING function
function
• "Feeder" locking device cannot be operated.
• Cable compartment cover cannot be removed.
OPEN OPEN OPEN • "Three-position disconnector" switching operation can be selected; operating lever for
the DISCONNECTING or READY-TO-EARTH operation can be inserted; three-position
disconnector can be operated.
• Circuit-breaker can be operated.
OPEN OPEN CLOSED
• Operating lever for READY-TO-EARTH operation cannot be inserted.
CLOSED --- OPEN
CLOSED --- CLOSED
• "Three-position disconnector" switching operation cannot be selected.
• "Three-position disconnector" switching operation cannot be selected.
• "Feeder" locking device can be operated.
--- CLOSED CLOSED
• Cable compartment cover can be removed.
• Operating lever for DISCONNECTING operation cannot be inserted.
--- CLOSED OPEN
➭ Put the switchgear panel into operation according to the installation and operating
instructions.
✔ The maintenance of the operating mechanism is completed.

Service information
29 Checks and maintenance work in case of special

operating conditions
If the switchgear is used in abnormally unfavorable indoor conditions beyond the normal
operating conditions (e.g. frequent heavy condensation, dust-ridden air, etc.) it is
recommended to perform a visual inspection of the NXPLUS C switchgear at regular intervals.
DANGER
Hazardous voltage.
➭ Isolate.
DANGER
Life-endangering voltage
Can cause death, injury or property damage. If the operating mechanism cover is
removed, do not touch any live parts.
➭ Switch off auxiliary voltage.
WARNING
been performed:
- Trip the MCB.
instructions:

Service information
Necessary checks
Depending on the panel type, the checks listed in the following table must be executed:
Panel type Circuit-breaker panel Circuit-breaker panel Ring-main Bus sectionalizer

with 30,000 operating panel panel
cycles
Activity Panel width [mm]
600 900 600 600 600 900

Check galvanically plated surfaces for traces of corrosion X X X X X X
Check lubrication of sliding surfaces X X X X X X
Check firm seating of all terminal connections X X X X X X
Check smooth operation of control gate and interrogation
X X X X X X
lever
Visual check of spring-operated mechanism X - - X X -
Visual check of spring-operated/stored-energy mechanism - - - - - -
with fuse tripping
Visual check of slow motion mechanism - X X - - X
Visual check of circuit-breaker operating mechanism X X X - - -
Visual check of vacuum contactor operating mechanism - - - - - -
Check functionality and smooth operation of the cable
X X X X X X
compartment interlock
Check fuse tripping - - - - - -
Panel type Disconnector Vacuum Vacuum contactor Metering Switch-disconnector

panel contactor panel with fuse panel panel with HV HRC
panel assembly fuses
Activity Panel width [mm]
600 900 600 600 600 600

Check galvanically plated surfaces for traces of corrosion X X X X X X
Check lubrication of sliding surfaces X X X X X X
Check firm seating of all terminal connections X X X X X X
Check smooth operation of control gate and interrogation
X X X X X X
lever
Visual check of spring-operated mechanism X - - - X
Visual check of spring-operated/stored-energy mechanism - - - - -
X
with fuse tripping
Visual check of slow motion mechanism - X - - - -
Visual check of circuit-breaker operating mechanism - - - - X X
Visual check of vacuum contactor operating mechanism - - X X - -
Check functionality and smooth operation of the cable
X X X X X X
compartment interlock
Check fuse tripping - - - X X X
29.1 Visual check at the operating mechanisms and the three-position switches
• Check galvanically plated surfaces for traces of corrosion.
• Check lubrication of sliding surfaces.
• Check firm seating of all terminal connections.
29.2 Visual check of spring-operated mechanism

Refers to panel types:
• Circuit-breaker panel (panel width 600 mm)
• Bus sectionalizer panel (panel width 600 mm)
• Disconnector panel (panel width 600 mm)
• Ring-main panel (panel width 600 mm)
• Vacuum contactor panel (panel width 600 mm)
• Metering panel (panel width 600 mm)

Service information
Spring-operated ➭ Check firm seating of all terminal connections ① .

mechanism ➭ Check lubrication of sliding surfaces ② .
➭ Check smooth operation of the interrogation lever ③ .
➭ Check smooth operation of the control gate ④ .
Fig. 181: Spring-operated mechanism
Cable compartment ➭ Check functionality and smooth operation of the cable compartment interlock ① .
interlock Lift the lever of the cable compartment interlock, and release it. The lever must move down
again automatically.
Fig. 182: Cable compartment interlock
Fuse tripping Check functionality and smooth operation of the fuse tripping.
• Vacuum contactor panel with HV HRC fuse assembly (panel width 600 mm)
• Metering panel (panel width 600 mm)
➭ Check firm seating of all terminal connections ① .
➭ Check smooth operation of tripping rocker ② , lubricate if necessary.
➭ Check whether the auxiliary switch ① (option) reacts when the tripping rocker is lifted
(clicking noise).

Service information
Fig. 183: Fuse tripping
29.3 Visual check of slow motion mechanism

• Circuit-breaker panel (panel width 900 mm)
• Bus sectionalizer (panel width 900 mm)
• Disconnector panel (panel width 900 mm)
• Circuit-breaker panel with increased number of 30000 operating cycles (panel width
600 mm)
Slow motion mechanism ➭ Check smooth operation of the interrogation lever ① .

➭ Check firm seating of all terminal connections ② .
➭ Check smooth operation of the control gate ③ .
Fig. 184: Slow motion mechanism

Service information
Cable compartment ➭ Check functionality and smooth operation of the cable compartment interlock ① :
interlock Lift the lever of the cable compartment interlock, and release it. The lever must move down
again automatically.
Fig. 185: Cable compartment Fig. 186: Cable compartment interlock (circuit-
interlock breaker panel with 30000 operating cycles)
29.4 Visual check of spring-operated/stored-energy mechanism

Refers to panel type:
• Switch-disconnector panel with HV HRC fuses
Spring-operated ➭ Check firm seating of all terminal connections ① .

mechanism ➭ Check lubrication of sliding surfaces ② .
➭ Check smooth operation of the interrogation lever ③ .
➭ Check smooth operation of the control gate ④ .
Fig. 187: Spring-operated/stored-energy mechanism
Cable compartment ➭ Check functionality and smooth operation of the cable compartment interlock ① .
interlock
Fig. 188: Cable compartment interlock

Service information
Fuse tripping
DANGER
Hazardous voltage.
➭ Isolate.
DANGER
Life-endangering voltage
Can cause death, injury or property damage. If the operating mechanism cover is
removed, do not touch any live parts.
➭ Switch off auxiliary voltage.
WARNING
been performed:
- Trip the MCB.
instructions:
Check functionality and smooth operation of the fuse tripping:

➭ Check firm seating of all terminal connections ① .
➭ Check smooth operation of tripping rocker, lubricate if necessary.
➭ Check whether the auxiliary switch ① (option) reacts when the tripping rocker is lifted
(clicking noise).
➭ Switch the spring-operated/stored-energy mechanism to CLOSED position.
➭ Pull the tripping rocker ② up manually.
✔ The spring-operated/stored-energy mechanism trips.

Service information
Fig. 189: Fuse tripping
The switch-disconnector is now in OPEN position, the spring-operated/stored-energy

mechanism is in CLOSED position. The switch-disconnector indicator shows a faulty position.
Switch the spring-operated/stored-energy mechanism to the same position as the switch-
disconnector:
➭ Switch the spring-operated/stored-energy mechanism to OPEN position (see operating and
installation Instructions).
✔ The switch-disconnector indicator shows the OPEN position again.
29.5 Visual check of circuit-breaker operating mechanism
Fig. 190: Circuit-breaker operating mechanism 3AH55

Service information
Fig. 191: Circuit-breaker operating mechanism 3AH25
➭ Check firm seating of all terminal connections ① (rectangular markings).

➭ Check lubrication of all sliding surfaces ② (circular markings).
29.6 Visual check of vacuum contactor operating mechanism
NOTICE
Removing the cover of the vacuum contactor operating mechanism
Can damage the operating mechanism.
➭ Do not remove the cover ① .
➭ In case of a functional failure of the vacuum contactor operating mechanism, please
contact the Siemens Service Hotline.
Fig. 192: Vacuum contactor operating mechanism

Service information
➭ Verify intact condition of the shaft ② (cracks, damages, etc.)

➭ Verify intact condition of the retaining elements ③ .
➭ Verify intact condition of the spring ④ .
➭ Check firm seating of all terminal connections ⑤ .
29.7 Cleaning, greasing and lubricating the operating mechanisms

• Clean the external parts of the switchgear and switching devices with a lint-free wiping
cloth at regular intervals.
Cleaning agent: Mild, customary household cleaner for general degreasing work and
cleaning work (solvent-free).
• If necessary, renew the anti-corrosion protection greasing.
• If necessary, lubricate the bearings.
NOTICE
Contact by cleaning agents
Can cause property damage. Joints and bearings which cannot be dismantled may be
damaged by cleaning agents.
➭ Do not use cleaning agents to clean joints and bearings which cannot be dismantled.
Operating mechanism of Use the following auxiliary means for the spring-operated mechanism, the spring-operated/
three-position switch stored-energy mechanism and the slow motion mechanism of the three-position switch:
• For bearings, sliding surfaces: Molykote (R) MKL-N Grease
Circuit-breaker operating Use the following aids for the circuit-breaker operating mechanism:
mechanism • For bearings, sliding surfaces: Isoflex Topas L 32, Klüber
• For bearings that are inaccessible for grease: Tellus Oil 32
• For bearings of the auxiliary switches: Tellus Oil 32
For suppliers and manufacturer information of lubricants: see page 284, "Permissible
lubricants".
Vacuum contactor It is not required to clean, grease or lubricate the operating mechanism of the vacuum
operating mechanism contactor.
29.8 Test operation of the operating mechanisms
DANGER
Hazardous voltage
Can cause death, injury or considerable property damage.
➭ Always observe the Five Safety Rules of Electrical Engineering.
➭ Observe the specifications for prevention of accidents.
➭ Observe the operating instructions and work instructions of the switchgear operator.
➭ Observe the the installation and operating instructions of the switchgear.
➭ Mount the front cover of the operating mechanisms.

If one of the operating mechanisms does not operate correctly, please contact the regional
Siemens representative.
➭ Operate the operating mechanism of the three-position switch several times mechanically
by hand for test.
➭ Operate the operating mechanism of the circuit-breaker several times mechanically by hand
for test.
➭ Operate the operating mechanism of the vacuum contactor electrically 5 times for test.

Service information
30 Permissible lubricants
Lubricants Manufacturer
Molykote (R) MKL-N Grease Dow Corning GmbH
Rheingaustr. 34
D-65201 Wiesbaden
Isoflex Topas L 32 Klüber - Lubrication KG
Geisenhauer Str. 7
Postfach 70 10 47
D-81310 Munich
Tellus Oil 32 Shell Direct GmbH
Suhrenkamp 71
D-22335 Hamburg
The following lubricants can be obtained from the regional Siemens representative:
Weight Lubricants Order No.

180 g Isoflex Topas L 32 3AX1133-3H
1 kg Isoflex Topas L 32 3AX1133-3E
1 kg Tellus Oil 32 3AX1133-2D
1 kg Molykote (R) MKL-N Grease 5000000082
31 Extending the switchgear or replacing panels and

components
The individual components, such as measuring instruments, current transformers, etc. can be
replaced. For switchgear extension and replacement of components, please contact the
regional Siemens representative. Due to the busbar concept, switchgear extension or panel
replacement is possible without gas work.
Information required for spare part orders of single components and devices:
• Type and serial number of the switchgear and the circuit-breaker (see rating plates)
• Precise designation of the device or component, if applicable on the basis of the information
and illustrations in the associated instructions, a drawing, sketch or circuit diagram

Annex
Annex
32 MCU-MH (Motor Control Unit - Module Housing)
32.1 Extract from the Technical Description

The following sections are an extract from the Technical Description of the electrical motor
control unit MCU-MH.
The complete Technical Description is available under the order number 953-0071.9.
32.2 Application
The MCU-MH controls the following motor operating mechanisms for three-position switches in
medium-voltage load-break switchgear and circuit-breaker switchgear:
• Spring-operated mechanism
• Spring-operated/stored-energy mechanism
• Slow motion mechanism
The MCU-MH is mounted in the module housing on standard top-hat rails.
Application The MCU-MH is equipped with a universal wide voltage range. It can optionally be connected
to different auxiliary and motor voltages. The auxiliary and motor voltages can be combined
and do not necessarily have to be identical.
32.3 Design, function
Fig. 193: MCU-MH in module housing Fig. 194: Dimensions of MCU-MH

(data in mm)
① Identification of connections of upper plugs ⑥ Upper module plug -X1.4
② Reset pushbutton ⑦ Upper module plug -X1.3
③ LED status indicator ⑧ Lower module plug -X1.2
④ Serial number in clear text ⑨ Lower module plug -X1.1
⑤ Identification of connections of lower plugs

Annex
32.4 Technical data
Binary inputs Command input, feedback and interlocking is done through a total of 9 binary inputs (BI).
Binary input Description Type Electrical function Function

1 Command inputs Active High active Disconnector in CLOSED position1
2 Disconnector in OPEN1 position
3 Earthing switch in CLOSED1 position
4 Earthing switch in OPEN1 position
5 Interlocking inputs Passive High active Total of all interlocking conditions, release of control
unit with applied high signal
6 Passive Low active Other interlock / 2-phase switching of the disconnector
and earthing switch function
7 Feedback inputs Passive High active Disconnector and earthing switch in OPEN1 position
8 Disconnector in CLOSED1 position
9 Earthing switch in CLOSED1 position
1
Depending on the panel type and the necessary sense of rotation of the motor, the assignment of the sense of rotation of the motor can
vary.
NOTICE
Functional failure due to insufficient voltage quality
The functioning of MCU-MH may be impaired.
➭ The voltage quality of the voltages used for auxiliary and load circuits must correspond to
applicable standards.
➭ If an AC control or AC load voltage is used, which is generated directly from single-phase
inverters, earth UN2~.
NOTICE
Functional failure due to incorrect circuit of the command inputs
The functioning of MCU-MH may be impaired.
➭ For activation of the command inputs for disconnector CLOSED, disconnector OPEN,
earthing switch OPEN and earthing switch CLOSED, do not use any external switching
contacts that are equipped with capacitors > 4.7 nF connected in parallel with the contact.
NOTICE
Damage to MCU-MH due to test voltages
If the specified limits (1 kV, 1 s) are exceeded during dielectric tests according to the
standard IEC 62271-200, the MCU-MH may be damaged by too high test voltages.
➭ Before performing the dielectric test, remove the connecting plugs at the MCU-MH.
32.5 Fault signals
Output of fault signals Fault signals at the unit are displayed via a red flashing LED status indicator.
Possible causes for a fault signal:
• An incorrect sense of rotation of the motor was detected while moving the operating
mechanism from disconnector OPEN / earthing switch OPEN position to
disconnector CLOSED / earthing switch CLOSED position.
• There is an internal MCU-MH fault (watchdog).
• The feedback monitoring time (runtime monitoring of the operating mechanism) for
protecting the drive motor and the mechanical system was exceeded.
• A command for moving the operating mechanism is applied to the active command inputs
(disconnector CLOSED / disconnector OPEN / earthing switch CLOSED / earthing
switch OPEN) for more than 5 minutes, although existing interlocking conditions prevent
the execution of this command.

Annex
• A command is applied to one of the active command inputs (disconnector CLOSED /

disconnector OPEN / earthing switch CLOSED / earthing switch OPEN) for more than
5 minutes, although the associated switching operation was completed successfully.
Clearing the fault mode Options for clearing the fault mode after the cause for the fault mode was eliminated:
• Through the reset button at the device (operation of the reset button: insert a thin, pointed
object through the opening at the front side.)
• By removing and re-applying the control voltage
32.6 Terminal assignment of motor control unit
Terminal Designation
-X1.1:1 Load voltage + (for AC supply L ~)
-X1.1:2 Load voltage - (for AC supply N ~)
-X1.1:3 Output motor voltage +
-X1.1:4 Output motor voltage -
-X1.2:5 BI 7: OPEN feedback from auxiliary switch
-X1.2:6 BI 8: Disconnector feedback from auxiliary switch
-X1.2:7 BI 9: Earthing switch feedback from auxiliary switch
-X1.2:8 Control voltage - (for AC supply N ~)
-X1.2:9 Control voltage + (for AC supply L ~)
-X1.3:10 BI 1: Disconnector CLOSED (active BI)1
-X1.3:11 BI2: Disconnector OPEN (active BI)1
-X1-3:12 BI 3: Earthing switch CLOSED (active BI)1
-X1.3:13 BI 4: Earthing switch OPEN (active BI)1
-X1.4:14 BI 5: Interlocking high (passive BI)
-X1.4:15 BI 6: Interlocking low (passive BI)
-X1.4:16 Floating contact, reverse interlocking to circuit-breaker (normally closed
contact)
-X1.4:17 Floating contact, reverse interlocking to circuit-breaker (normally closed
contact)
1 Depending on the panel type and the necessary sense of rotation of the
motor, the assignment of the sense of rotation of the motor can vary.

Siemens Service Hotline
Siemens Service Hotline

• Customer Support Global
- +49 180 524 7000
- support.energy@siemens.com
- 24 hours
• Customer Support Brazil (for the Brazilian market only)
- +55 11 4585 8040
- suporte.br@siemens.com
- Local working hours
• Customer Support India (for Indian market only)
- +91 1 800 419 7477
- service.energy.in@siemens.com
- Local working hours

33 Index
A Circuit-breaker, opening ............................................... 190
Accessories..................................................................... 54 Circuit-breaker, operating ............................................. 190
Accessories, checking ................................................... 179 Circuit-breaker, test operation ...................................... 191
Air guides, mounting .................................................... 151 Circuit-breaker, vacuum interrupters ............................... 24
Annex .......................................................................... 285 Closing spring, charging with hand crank...................... 190
Application ................................................................... 285 Comments on EMC ......................................................... 98
Applying, operating voltage .......................................... 184 Commissioning............................................................. 177
Aseismic capacity............................................................ 60 Completeness of delivery .............................................. 100
Assembly, preconditions ............................................... 107 Component, replacing .................................................. 284
Auxiliary circuits, connection ........................................ 166 Components................................................................... 24
Auxiliary means, installation ........................................... 97 Constructional data, foundation...................................... 84
B Constructional stipulations.............................................. 81
Binary inputs ................................................................ 286 Control elements .......................................................... 187
Bus sectionalizer ............................................................. 19 Core drillings .................................................................. 88
Busbar covers, installation ............................................ 144 Current transformers, installation.................................. 124
Busbar support, installation .......................................... 122
D
Busbar system ................................................................ 33 Degree of protection version, IP32D.............................. 175
Busbar, energizing ........................................................ 185 Description ..................................................................... 10
Busbars, assembly ........................................................ 111 Dew point, checking ..................................................... 268
C Disconnector panel ......................................................... 17
Cable basement.............................................................. 84 Due application ................................................................ 9
Cable bracket, aligning ................................................. 160
E
Cable bracket, mounting............................................... 160 Earthing accessories ..................................................... 201
Cable connection............................................................ 34 Earthing busbar, installation ......................................... 132
Cable connection, connecting T-plugs........................... 158 Earthing system.............................................................. 84
Cable connection, double cables ................................... 162 Earthing, switchgear..................................................... 132
Cable connection, panels as of 2000 A .......................... 163 Electrical connections ................................................... 154
Cable connection, triple cables...................................... 162 Endurance classes........................................................... 77
Cables, testing .............................................................. 266 Erecting, switchgear ..................................................... 100
CAPDIS ......................................................................... 205 Evenness, straightness.................................................... 84
Checking, accessories ................................................... 179 Extension with individual panels ................................... 154
Circuit diagrams, correcting ......................................... 184
F
Circuit-breaker................................................................ 24 Fault mode, clearing ..................................................... 287
Circuit-breaker 3AH25 with 30000 operating cycles, Features ......................................................................... 10
maintenance ................................................................ 268
Feeder voltage transformer, connecting........................ 213
Circuit-breaker operating mechanism, visual check ....... 281
Feeder voltage transformer, disconnecting ................... 212
Circuit-breaker panel, readjusting the freewheel of the
pushbuttons ................................................................. 180 Final work .................................................................... 177
Circuit-breaker panels ..................................................... 13 Floor cover ................................................................... 155
Circuit-breaker tripping signal ......................................... 75 Floor openings, fixing points........................................... 85
Circuit-breaker, activating undervoltage release ............ 181 Floor, construction ......................................................... 83
Circuit-breaker, closing ................................................. 190 Floor, load-bearing capacity ............................................ 82
Circuit-breaker, design.................................................... 24 Forced sequence circuit ................................................ 219
Circuit-breaker, locking device ...................................... 189 Forced sequence circuit 600 mm .................................. 218

Forced sequence circuit 900 mm........................... 224, 225 LRM plug-in sockets, verification of safe isolation from
supply ..........................................................................203
Foundation, fastening the panel ................................... 110
Lubricants, permissible .................................................284
Function test ................................................................ 179
Function test, electrical ................................................. 182 M
Maintenance, circuit-breaker 3AH25 with 30000
Function test, mechanical ............................................. 180
operating cycles............................................................268
G Motor operating mechanism of three-position switch, fuse
Gas quality, checking .................................................... 268 protection table ............................................................. 76
H O
Hand crank, charging the closing spring ........................ 190 Operating mechanism, cleaning ....................................283
High-voltage test, power consumption per panel............. 58 Operating mechanism, greasing....................................283
Horizontal pressure relief duct, installation.................... 134 Operating mechanism, lubricating ................................283
Horizontal pressure relief duct, installing rear Operating mechanisms, three-position switch ................. 27
evacuation.................................................................... 139
Operating times .............................................................. 73
Horizontal pressure relief duct, installing rear wall......... 139
Operating voltage, applying ..........................................184
HR plug-in sockets, verification of safe isolation
Operation .....................................................................186
from supply .................................................................. 203
Operations counter .......................................................188
HV HRC fuse assembly..................................................... 32
HV HRC fuse-links, replacing.......................................... 208 P
Packing and transport unit ............................................100
HV HRC fuse-links, selection ............................................ 61
Panel versions ........................................................... 13, 17
I
Panel, fastening to the foundation ................................110
Indicators ..................................................................... 187
Panel, replacing ............................................................284
Information to Siemens before delivery ........................... 96
Panels, aligning ............................................................108
Installation ..................................................................... 81
Panels, joining ...................................................... 108, 109
Installation, auxiliary means ............................................ 97
Partition class ................................................................. 59
Installation, current transformer.................................... 124
Personal protection ........................................................... 7
Installation, earthing busbar ......................................... 132
Personal protective equipment (PPE) ................................. 7
Installation, preparing..................................................... 96
Personnel, instructing ...................................................179
Installation, switchgear termination .............................. 143
Position indicators.........................................................188
Installation, tools ............................................................ 97
Power losses ................................................................... 59
Installation, voltage transformer ................................... 127
Power-frequency voltage test on site.............................183
Installing rear evacuation, horizontal pressure
relief duct ..................................................................... 139 PPE ................................................................................... 7
Insulating gas ................................................................. 79 Primary injection test ....................................................184
Interlocking solenoids, unlocking .................................. 181 Protection against vertically falling water drops,
high low-voltage compartment .....................................174
Interlocks........................................................................ 53
Protection tripping ........................................................195
IP31D ........................................................................... 171
Protective equipment........................................................ 7
IP31D, IP32D, IP34D...................................................... 171
Pushbutton, readjusting the freewheel..........................180
IP32D, degree of protection version .............................. 175
IP34D ........................................................................... 176 Q
Qualified personnel........................................................... 9
L
Line protection of magnet coil, vacuum contactor ........... 79 R
Rated operating sequences ............................................. 73
Line protection of motor operating mechanism, vacuum
circuit-breaker ................................................................ 74 Rating plates ................................................................... 72
Locking devices............................................................... 53 Ready-for-service indicator ...................................... 52, 189
Low-voltage compartment, craning............................... 104 Ready-for-service indicator, checking ............................105
Low-voltage compartment, installation ......................... 133 Recycling ........................................................................ 80

Resistance against shock, vibration, earthquakes............. 87 Test operation, operating mechanism ........................... 283
Ring-main panel ............................................................. 23 Test voltages, busbar voltage transformers ..................... 58
Room planning ............................................................... 82 Three-position disconnector............................................ 26
S Three-position switch, closing....................................... 193

Safety instructions ............................................................ 6 Three-position switch, de-earthing................................ 194
Safety, shock and vibration ............................................. 61 Three-position switch, earthing..................................... 194
Seaworthy crate, preparing storage ................................ 96 Three-position switch, emergency operation with slow
Secondary wiring, connection ....................................... 166 motion mechanism....................................................... 196
Seismic withstand capability ........................................... 11 Three-position switch, motor operating mechanism ...... 195
Service Hotline ............................................................. 288 Three-position switch, opening ..................................... 193
Service instructions....................................................... 268 Three-position switch, operation................................... 192
Service life, end .............................................................. 80 Three-position switch, ready-to-earth............................ 194
Short instructions ......................................................... 214 Three-position switch-disconnector................................. 26
Signal terms and definitions.............................................. 6 Three-position switch-disconnector, technical data ......... 76
Slow motion mechanism, visual check .......................... 278 Three-positon disconnector, technical data ..................... 76
Splashing water from any direction ............................... 176 Tools, installation ........................................................... 97
Spring charged indicator............................................... 188 Transport...................................................................... 101
Spring-operated mechanism ........................................... 27 Transport braces, removal............................................. 110
Spring-operated mechanism, visual check ..................... 276 Transport damages ....................................................... 100
Spring-operated/stored-energy mechanism, Transport regulations ..................................................... 95

visual check .................................................................. 279 Transport unit and packing ........................................... 100
Stability braces, removal ............................................... 110 Transport units, installation .......................................... 104
Standards, electromagnetic compatibility, EMC ............... 60 Transport, without wooden pallets................................ 102
Storage room/space, preparing ....................................... 96 U
Stored-energy mechanism .............................................. 27 Undervoltage release ...................................................... 75
Surge arrester................................................................. 34 Unloading .................................................................... 101
Surge arresters, connection .......................................... 164 Unloading, switchgear .................................................. 100
Surge limiters, connection ............................................ 165 V
Switch-disconnector panel .............................................. 21 Vacuum circuit-breaker ................................................... 72
Switch-fuse combination, protection tripping................ 195 Vacuum circuit-breaker 3AH55, motor operating
mechanism..................................................................... 74
Switchgear room, preparing for installation .................... 81
Vacuum circuit-breaker 3AH55, shunt release ................. 75
Switchgear termination, installation.............................. 143
Vacuum circuit-breaker, closing solenoid......................... 75
Switchgear, assembling ................................................ 107
Vacuum contactor operating mechanism, visual check .. 282
Switchgear, extending .................................................. 284
Varistor module .............................................................. 75
T
Verification of safe isolation from supply....................... 203
Technical data ................................................................ 58
Verification of safe isolation from supply,
Technical data, complete switchgear............................... 58
HR/LRM plug-in sockets................................................. 203
Technical data, three-position switch-disconnector ......... 76
Visual check, operating mechanisms ............................. 276
Technical data, three-positon disconnector ..................... 76
Visual check, three-position switch ............................... 276
Technical data, vacuum circuit-breaker 3AH55 ................ 72
VOIS............................................................................. 205
Terminal assignment .................................................... 287
Voltage detecting systems .............................................. 54
Test adapter, voltage transformer ................................... 30
Voltage transformer, conformity ..................................... 30
Test operation .............................................................. 179
Voltage transformer, installation................................... 127
Test operation, circuit-breaker ...................................... 191
W
Test operation, faults .................................................... 182
Water drops, vertically falling ....................................... 171

WEGA ........................................................................... 207 Work-in-progress earthing.............................................201
Wooden pallets, removing ............................................ 101

Imprint
Siemens AG
Energy Management
Medium Voltage & Systems
Switchgear Factory Frankfurt
Carl-Benz-Str. 22
D-60386 Frankfurt
© Siemens AG 2018

Nxplus C

Uploaded by

Copyright:

Available Formats

Nxplus C

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nxplus C

Uploaded by

Copyright:

Available Formats

Medium-Voltage Switchgear

Type NXPLUS C Fixed-Mounted Circuit-Breaker Switchgear up to 24 kV,

M edium -Voltage S witchgear

Order No.: 802-9081.9

2/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 3/293

Operation........................................................ 186 26.6 Operating bus sectionalizer panels with 600 mm

4/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 5/293

6/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 7/293

Removing the front cover from the operating mechanism compartment

Fig. 1: "Spring not charged" indication Fig. 2: "Spring charged" indication

8/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 9/293

Personal safety • Safe-to-touch due to metal enclosure of live parts

10/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 11/293

Circuit-breaker panel Disconnector panel Switch-disconnector panel Bus sectionalizer

Metering panel Vacuum contactor panel Ring-main panel

Vacuum circuit- Three-position switch- Capacitive voltage

These components can be

HV HRC fuse Vacuum contactor

12/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

8 Examples for panel versions

8.1 Circuit-breaker panels

① Rear pressure relief duct

Fig. 3: Circuit-breaker panel (630 A)

① Rear pressure relief duct

Fig. 4: Circuit-breaker panel (1000 A)

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 13/293

① Rear pressure relief duct

* 752 mm for deep cable compartment cover

Fig. 5: Circuit-breaker panel (1250 A)

* 2650 mm for high low-voltage compartment

Fig. 6: Circuit-breaker panel (2000 A and 2500 A)

14/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

① Rear pressure relief duct

* 2650 mm for high low-voltage compartment

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 15/293

① Rear pressure relief duct / cable

* 2650 mm for high low-voltage

Fig. 8: Circuit-breaker panel with top-rear cable connection (1250 A)

Fig. 9: Circuit-breaker panel with bottom-rear cable connection (1250 A)

16/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

8.2 Disconnector panels

① Rear pressure relief duct

Fig. 10: Disconnector panel (1000 A)

① Rear pressure relief duct

Fig. 11: Disconnector panel (1250 A)

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 17/293

Fig. 12: Disconnector panel (2000 A and 2500 A)

18/293 Revision 11 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • 802-9081.9

8.3 Bus sectionalizer

① Rear pressure relief duct (option)

* 2650 mm for high low-voltage

802-9081.9 • INSTALLATION AND OPERATING INSTRUCTIONS • NXPLUS C • Revision 11 19/293

* 2650 mm for high low-

① Rear pressure relief duct (option)