742266
742266
742266
Dual Polarization X X
Half-power Beam Width 65° 65°
Adjust. Electr. Downtilt 0°–7° 0°– 6°
set by hand or by optional RCU (Remote Control Unit)
65°
125°
7.5°
1710 – 2180 824 – 960 824 – 960 1710–2180
10 10 –45° –45° +45° +45°
3
dB
dB
dB
3 3
Packing size 2815 x 302 x 192 mm
0 0
Height/width/depth 2516 / 262 / 139 mm
Horizontal Pattern Vertical Pattern
0°– 6° electrical downtilt
9
Weight Units per
Type No. Description Remarks
approx. antenna
2516
2567
2607
850 10007 1 downtilt kit Downtilt angle: 0° – 8° 5.9 kg 1
The downtilt kit can only be used in combination with the clamps
type nos. 738 546, 850 10002, 850 10003.
Wall mounting: No additional mounting kit is needed.
139
– Low temperature: –55 °C
52
Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are
obliged to point out certain risks that may arise when products are used under extraordinary operating
conditions.
Subject to alteration.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which
includes the static mechanical load imposed on an antenna by wind at maximum velocity.
Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by
oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground.
These facts must be considered during the site planning process.
The installation team must be properly qualified and also be familiar with the relevant national safety
936.2702/a
regulations.
The details given in our data sheets have to be followed carefully when installing the antennas and
accessories.
The limits for the coupling torque of RF-connectors, recommended by the connector manufacturers
must be obeyed.
1
1
2 2
➀ Adjustment wheel with ➀ Thread for fixing of the To set the downtilt angle
twist-lock function. protective cap or the RCU exactly, you must look hori-
➁ Downtilt spindle with inte- (Remote Control Unit). zontally at the scale. The
grated scale. ➁ Gearwheel for RCU-power lower edge of the gearwheel
drive. must be used for alignment
purposes.
max.° – 0°
Remove protective cap. Set downtilt angle by rotating Screw on the protective cap
the adjustment wheel. again.
Attachment of the RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
Remove the protective cap Completely remove the black Push the attachment nut of Tighten the RCU attachment
completely from the antenna. adjustement wheel by simply the RCU down towards the nut using a torque-wrench;
Check the proper functioning pulling it downwards. housing. wrench width = 41 mm,
of the phase-shifter over the min. torque = 15 Nm,
Place the RCU carefully over
entire adjustment range, by max. torque = 18 Nm.
the adjustment spindle,
Subject to alteration.
twisting the adjustment wheel observing the correct align- Please note!
in such a way that the spindle ment of the RCU with regards In cases where a mechani-
moves completely in and out.
to the antenna, i.e. the flat cal downtilt unit is installed,
Reset the downtilt to the surfaces of the attachment this downtilt must not be
previous value. fixture on the antenna side set for a downtilt of more
and those inside the RCU than 14 degrees.
housing must lie flat against
each other.
936.2702/a
Please note:
In order not to damage the interfaces, please make sure that only the right tools are used. For fixing the nut of the
connector we recommend using a common torque-wrench with a suitable wrench width.
4 3
2 1
There are four interfaces for feeding the To make the installation of the feederlines
antenna located at the bottom. and the connectors easier, the interfaces are
arranged on two levels.
Start with the rearside located interface no. 1. After feederline installation the remote control For full description of RCU installation see
Place the connector carefully and fix the nut units (RCU) can be attached. datasheet Type no. 860 10003.
using a torque-wrench (according to the
manufacturers guidelines).
The further sequence for the installation is:
feederlines no. 2, 3, 4.
Subject to alteration.
936.2702/a
Please note:
Sealing of the correctly installed connector’s cap nuts for additional weather protection is not required, nor is it
recommended by the connector manufacturers.